Skip to contentSkip to conversation

staging: iio: accel: Move header file content to source file

PATCH Superseded simran singhal 3 participants 6 messages Feb 28, 2017

Subsystems (4)

v2 of 3 Superseded Latest is v3 →

lore
Share & tools
lore
#0 lore raw

PATCH v2 1/1 staging: iio: accel: Move header file content to source file

The contents of the header file are used only by this single source file. Move content into .c and remove .h.

---

v2:
-Removing ifndef and define

 drivers/staging/iio/accel/adis16201.h      | 144 -----------------------------
 drivers/staging/iio/accel/adis16201_core.c | 142 +++++++++++++++++++++++++++-
 2 files changed, 141 insertions(+), 145 deletions(-)
 delete mode 100644 drivers/staging/iio/accel/adis16201.h
drivers/staging/iio/accel/adis16201.h deleted +0 -144
deleted file mode 100644
index 64844ad..0000000
@@ -1,144 +0,0 @@
-#ifndef SPI_ADIS16201_H_
-#define SPI_ADIS16201_H_
-
-#define ADIS16201_STARTUP_DELAY	220 /* ms */
-
-/* Flash memory write count */
-#define ADIS16201_FLASH_CNT      0x00
-
-/* Output, power supply */
-#define ADIS16201_SUPPLY_OUT     0x02
-
-/* Output, x-axis accelerometer */
-#define ADIS16201_XACCL_OUT      0x04
-
-/* Output, y-axis accelerometer */
-#define ADIS16201_YACCL_OUT      0x06
-
-/* Output, auxiliary ADC input */
-#define ADIS16201_AUX_ADC        0x08
-
-/* Output, temperature */
-#define ADIS16201_TEMP_OUT       0x0A
-
-/* Output, x-axis inclination */
-#define ADIS16201_XINCL_OUT      0x0C
-
-/* Output, y-axis inclination */
-#define ADIS16201_YINCL_OUT      0x0E
-
-/* Calibration, x-axis acceleration offset */
-#define ADIS16201_XACCL_OFFS     0x10
-
-/* Calibration, y-axis acceleration offset */
-#define ADIS16201_YACCL_OFFS     0x12
-
-/* x-axis acceleration scale factor */
-#define ADIS16201_XACCL_SCALE    0x14
-
-/* y-axis acceleration scale factor */
-#define ADIS16201_YACCL_SCALE    0x16
-
-/* Calibration, x-axis inclination offset */
-#define ADIS16201_XINCL_OFFS     0x18
-
-/* Calibration, y-axis inclination offset */
-#define ADIS16201_YINCL_OFFS     0x1A
-
-/* x-axis inclination scale factor */
-#define ADIS16201_XINCL_SCALE    0x1C
-
-/* y-axis inclination scale factor */
-#define ADIS16201_YINCL_SCALE    0x1E
-
-/* Alarm 1 amplitude threshold */
-#define ADIS16201_ALM_MAG1       0x20
-
-/* Alarm 2 amplitude threshold */
-#define ADIS16201_ALM_MAG2       0x22
-
-/* Alarm 1, sample period */
-#define ADIS16201_ALM_SMPL1      0x24
-
-/* Alarm 2, sample period */
-#define ADIS16201_ALM_SMPL2      0x26
-
-/* Alarm control */
-#define ADIS16201_ALM_CTRL       0x28
-
-/* Auxiliary DAC data */
-#define ADIS16201_AUX_DAC        0x30
-
-/* General-purpose digital input/output control */
-#define ADIS16201_GPIO_CTRL      0x32
-
-/* Miscellaneous control */
-#define ADIS16201_MSC_CTRL       0x34
-
-/* Internal sample period (rate) control */
-#define ADIS16201_SMPL_PRD       0x36
-
-/* Operation, filter configuration */
-#define ADIS16201_AVG_CNT        0x38
-
-/* Operation, sleep mode control */
-#define ADIS16201_SLP_CNT        0x3A
-
-/* Diagnostics, system status register */
-#define ADIS16201_DIAG_STAT      0x3C
-
-/* Operation, system command register */
-#define ADIS16201_GLOB_CMD       0x3E
-
-/* MSC_CTRL */
-
-/* Self-test enable */
-#define ADIS16201_MSC_CTRL_SELF_TEST_EN	        BIT(8)
-
-/* Data-ready enable: 1 = enabled, 0 = disabled */
-#define ADIS16201_MSC_CTRL_DATA_RDY_EN	        BIT(2)
-
-/* Data-ready polarity: 1 = active high, 0 = active low */
-#define ADIS16201_MSC_CTRL_ACTIVE_HIGH	        BIT(1)
-
-/* Data-ready line selection: 1 = DIO1, 0 = DIO0 */
-#define ADIS16201_MSC_CTRL_DATA_RDY_DIO1	BIT(0)
-
-/* DIAG_STAT */
-
-/* Alarm 2 status: 1 = alarm active, 0 = alarm inactive */
-#define ADIS16201_DIAG_STAT_ALARM2        BIT(9)
-
-/* Alarm 1 status: 1 = alarm active, 0 = alarm inactive */
-#define ADIS16201_DIAG_STAT_ALARM1        BIT(8)
-
-/* SPI communications failure */
-#define ADIS16201_DIAG_STAT_SPI_FAIL_BIT   3
-
-/* Flash update failure */
-#define ADIS16201_DIAG_STAT_FLASH_UPT_BIT  2
-
-/* Power supply above 3.625 V */
-#define ADIS16201_DIAG_STAT_POWER_HIGH_BIT 1
-
-/* Power supply below 3.15 V */
-#define ADIS16201_DIAG_STAT_POWER_LOW_BIT  0
-
-/* GLOB_CMD */
-
-#define ADIS16201_GLOB_CMD_SW_RESET	BIT(7)
-#define ADIS16201_GLOB_CMD_FACTORY_CAL	BIT(1)
-
-#define ADIS16201_ERROR_ACTIVE          BIT(14)
-
-enum adis16201_scan {
-	ADIS16201_SCAN_ACC_X,
-	ADIS16201_SCAN_ACC_Y,
-	ADIS16201_SCAN_INCLI_X,
-	ADIS16201_SCAN_INCLI_Y,
-	ADIS16201_SCAN_SUPPLY,
-	ADIS16201_SCAN_AUX_ADC,
-	ADIS16201_SCAN_TEMP,
-};
-
-#endif /* SPI_ADIS16201_H_ */
drivers/staging/iio/accel/adis16201_core.c +141 -1

148 lines not on this page · raw message

Signature · 1 line
2.7.4
maintainer
#1 lore raw
Quoted 4 lines · simran singhal

The contents of the header file are used only by this single source file. Move content into .c and remove .h.

Applied to the togreg branch of iio.git and pushed out as testing for the autobuilders to play with it.

Thanks,

Jonathan

Quoted 314 lines

---

v2:
-Removing ifndef and define

 drivers/staging/iio/accel/adis16201.h      | 144 -----------------------------
 drivers/staging/iio/accel/adis16201_core.c | 142 +++++++++++++++++++++++++++-
 2 files changed, 141 insertions(+), 145 deletions(-)
 delete mode 100644 drivers/staging/iio/accel/adis16201.h
drivers/staging/iio/accel/adis16201.h deleted +0 -144
deleted file mode 100644
index 64844ad..0000000
@@ -1,144 +0,0 @@
-#ifndef SPI_ADIS16201_H_
-#define SPI_ADIS16201_H_
-
-#define ADIS16201_STARTUP_DELAY	220 /* ms */
-
-/* Flash memory write count */
-#define ADIS16201_FLASH_CNT      0x00
-
-/* Output, power supply */
-#define ADIS16201_SUPPLY_OUT     0x02
-
-/* Output, x-axis accelerometer */
-#define ADIS16201_XACCL_OUT      0x04
-
-/* Output, y-axis accelerometer */
-#define ADIS16201_YACCL_OUT      0x06
-
-/* Output, auxiliary ADC input */
-#define ADIS16201_AUX_ADC        0x08
-
-/* Output, temperature */
-#define ADIS16201_TEMP_OUT       0x0A
-
-/* Output, x-axis inclination */
-#define ADIS16201_XINCL_OUT      0x0C
-
-/* Output, y-axis inclination */
-#define ADIS16201_YINCL_OUT      0x0E
-
-/* Calibration, x-axis acceleration offset */
-#define ADIS16201_XACCL_OFFS     0x10
-
-/* Calibration, y-axis acceleration offset */
-#define ADIS16201_YACCL_OFFS     0x12
-
-/* x-axis acceleration scale factor */
-#define ADIS16201_XACCL_SCALE    0x14
-
-/* y-axis acceleration scale factor */
-#define ADIS16201_YACCL_SCALE    0x16
-
-/* Calibration, x-axis inclination offset */
-#define ADIS16201_XINCL_OFFS     0x18
-
-/* Calibration, y-axis inclination offset */
-#define ADIS16201_YINCL_OFFS     0x1A
-
-/* x-axis inclination scale factor */
-#define ADIS16201_XINCL_SCALE    0x1C
-
-/* y-axis inclination scale factor */
-#define ADIS16201_YINCL_SCALE    0x1E
-
-/* Alarm 1 amplitude threshold */
-#define ADIS16201_ALM_MAG1       0x20
-
-/* Alarm 2 amplitude threshold */
-#define ADIS16201_ALM_MAG2       0x22
-
-/* Alarm 1, sample period */
-#define ADIS16201_ALM_SMPL1      0x24
-
-/* Alarm 2, sample period */
-#define ADIS16201_ALM_SMPL2      0x26
-
-/* Alarm control */
-#define ADIS16201_ALM_CTRL       0x28
-
-/* Auxiliary DAC data */
-#define ADIS16201_AUX_DAC        0x30
-
-/* General-purpose digital input/output control */
-#define ADIS16201_GPIO_CTRL      0x32
-
-/* Miscellaneous control */
-#define ADIS16201_MSC_CTRL       0x34
-
-/* Internal sample period (rate) control */
-#define ADIS16201_SMPL_PRD       0x36
-
-/* Operation, filter configuration */
-#define ADIS16201_AVG_CNT        0x38
-
-/* Operation, sleep mode control */
-#define ADIS16201_SLP_CNT        0x3A
-
-/* Diagnostics, system status register */
-#define ADIS16201_DIAG_STAT      0x3C
-
-/* Operation, system command register */
-#define ADIS16201_GLOB_CMD       0x3E
-
-/* MSC_CTRL */
-
-/* Self-test enable */
-#define ADIS16201_MSC_CTRL_SELF_TEST_EN	        BIT(8)
-
-/* Data-ready enable: 1 = enabled, 0 = disabled */
-#define ADIS16201_MSC_CTRL_DATA_RDY_EN	        BIT(2)
-
-/* Data-ready polarity: 1 = active high, 0 = active low */
-#define ADIS16201_MSC_CTRL_ACTIVE_HIGH	        BIT(1)
-
-/* Data-ready line selection: 1 = DIO1, 0 = DIO0 */
-#define ADIS16201_MSC_CTRL_DATA_RDY_DIO1	BIT(0)
-
-/* DIAG_STAT */
-
-/* Alarm 2 status: 1 = alarm active, 0 = alarm inactive */
-#define ADIS16201_DIAG_STAT_ALARM2        BIT(9)
-
-/* Alarm 1 status: 1 = alarm active, 0 = alarm inactive */
-#define ADIS16201_DIAG_STAT_ALARM1        BIT(8)
-
-/* SPI communications failure */
-#define ADIS16201_DIAG_STAT_SPI_FAIL_BIT   3
-
-/* Flash update failure */
-#define ADIS16201_DIAG_STAT_FLASH_UPT_BIT  2
-
-/* Power supply above 3.625 V */
-#define ADIS16201_DIAG_STAT_POWER_HIGH_BIT 1
-
-/* Power supply below 3.15 V */
-#define ADIS16201_DIAG_STAT_POWER_LOW_BIT  0
-
-/* GLOB_CMD */
-
-#define ADIS16201_GLOB_CMD_SW_RESET	BIT(7)
-#define ADIS16201_GLOB_CMD_FACTORY_CAL	BIT(1)
-
-#define ADIS16201_ERROR_ACTIVE          BIT(14)
-
-enum adis16201_scan {
-	ADIS16201_SCAN_ACC_X,
-	ADIS16201_SCAN_ACC_Y,
-	ADIS16201_SCAN_INCLI_X,
-	ADIS16201_SCAN_INCLI_Y,
-	ADIS16201_SCAN_SUPPLY,
-	ADIS16201_SCAN_AUX_ADC,
-	ADIS16201_SCAN_TEMP,
-};
-
-#endif /* SPI_ADIS16201_H_ */
drivers/staging/iio/accel/adis16201_core.c +141 -1
index 7963d4a..dcf8463 100644
@@ -20,7 +20,147 @@
 #include <linux/iio/buffer.h>
 #include <linux/iio/imu/adis.h>
 
-#include "adis16201.h"
+#define ADIS16201_STARTUP_DELAY	220 /* ms */
+
+/* Flash memory write count */
+#define ADIS16201_FLASH_CNT      0x00
+
+/* Output, power supply */
+#define ADIS16201_SUPPLY_OUT     0x02
+
+/* Output, x-axis accelerometer */
+#define ADIS16201_XACCL_OUT      0x04
+
+/* Output, y-axis accelerometer */
+#define ADIS16201_YACCL_OUT      0x06
+
+/* Output, auxiliary ADC input */
+#define ADIS16201_AUX_ADC        0x08
+
+/* Output, temperature */
+#define ADIS16201_TEMP_OUT       0x0A
+
+/* Output, x-axis inclination */
+#define ADIS16201_XINCL_OUT      0x0C
+
+/* Output, y-axis inclination */
+#define ADIS16201_YINCL_OUT      0x0E
+
+/* Calibration, x-axis acceleration offset */
+#define ADIS16201_XACCL_OFFS     0x10
+
+/* Calibration, y-axis acceleration offset */
+#define ADIS16201_YACCL_OFFS     0x12
+
+/* x-axis acceleration scale factor */
+#define ADIS16201_XACCL_SCALE    0x14
+
+/* y-axis acceleration scale factor */
+#define ADIS16201_YACCL_SCALE    0x16
+
+/* Calibration, x-axis inclination offset */
+#define ADIS16201_XINCL_OFFS     0x18
+
+/* Calibration, y-axis inclination offset */
+#define ADIS16201_YINCL_OFFS     0x1A
+
+/* x-axis inclination scale factor */
+#define ADIS16201_XINCL_SCALE    0x1C
+
+/* y-axis inclination scale factor */
+#define ADIS16201_YINCL_SCALE    0x1E
+
+/* Alarm 1 amplitude threshold */
+#define ADIS16201_ALM_MAG1       0x20
+
+/* Alarm 2 amplitude threshold */
+#define ADIS16201_ALM_MAG2       0x22
+
+/* Alarm 1, sample period */
+#define ADIS16201_ALM_SMPL1      0x24
+
+/* Alarm 2, sample period */
+#define ADIS16201_ALM_SMPL2      0x26
+
+/* Alarm control */
+#define ADIS16201_ALM_CTRL       0x28
+
+/* Auxiliary DAC data */
+#define ADIS16201_AUX_DAC        0x30
+
+/* General-purpose digital input/output control */
+#define ADIS16201_GPIO_CTRL      0x32
+
+/* Miscellaneous control */
+#define ADIS16201_MSC_CTRL       0x34
+
+/* Internal sample period (rate) control */
+#define ADIS16201_SMPL_PRD       0x36
+
+/* Operation, filter configuration */
+#define ADIS16201_AVG_CNT        0x38
+
+/* Operation, sleep mode control */
+#define ADIS16201_SLP_CNT        0x3A
+
+/* Diagnostics, system status register */
+#define ADIS16201_DIAG_STAT      0x3C
+
+/* Operation, system command register */
+#define ADIS16201_GLOB_CMD       0x3E
+
+/* MSC_CTRL */
+
+/* Self-test enable */
+#define ADIS16201_MSC_CTRL_SELF_TEST_EN	        BIT(8)
+
+/* Data-ready enable: 1 = enabled, 0 = disabled */
+#define ADIS16201_MSC_CTRL_DATA_RDY_EN	        BIT(2)
+
+/* Data-ready polarity: 1 = active high, 0 = active low */
+#define ADIS16201_MSC_CTRL_ACTIVE_HIGH	        BIT(1)
+
+/* Data-ready line selection: 1 = DIO1, 0 = DIO0 */
+#define ADIS16201_MSC_CTRL_DATA_RDY_DIO1	BIT(0)
+
+/* DIAG_STAT */
+
+/* Alarm 2 status: 1 = alarm active, 0 = alarm inactive */
+#define ADIS16201_DIAG_STAT_ALARM2        BIT(9)
+
+/* Alarm 1 status: 1 = alarm active, 0 = alarm inactive */
+#define ADIS16201_DIAG_STAT_ALARM1        BIT(8)
+
+/* SPI communications failure */
+#define ADIS16201_DIAG_STAT_SPI_FAIL_BIT   3
+
+/* Flash update failure */
+#define ADIS16201_DIAG_STAT_FLASH_UPT_BIT  2
+
+/* Power supply above 3.625 V */
+#define ADIS16201_DIAG_STAT_POWER_HIGH_BIT 1
+
+/* Power supply below 3.15 V */
+#define ADIS16201_DIAG_STAT_POWER_LOW_BIT  0
+
+/* GLOB_CMD */
+
+#define ADIS16201_GLOB_CMD_SW_RESET	BIT(7)
+#define ADIS16201_GLOB_CMD_FACTORY_CAL	BIT(1)
+
+#define ADIS16201_ERROR_ACTIVE          BIT(14)
+
+enum adis16201_scan {
+	ADIS16201_SCAN_ACC_X,
+	ADIS16201_SCAN_ACC_Y,
+	ADIS16201_SCAN_INCLI_X,
+	ADIS16201_SCAN_INCLI_Y,
+	ADIS16201_SCAN_SUPPLY,
+	ADIS16201_SCAN_AUX_ADC,
+	ADIS16201_SCAN_TEMP,
+};
+
+#endif /* SPI_ADIS16201_H_ */
 
 static const u8 adis16201_addresses[] = {
 	[ADIS16201_SCAN_ACC_X] = ADIS16201_XACCL_OFFS,
maintainer
#2 lore raw
Quoted 11 lines · Jonathan Cameron
Quoted 4 lines · simran singhal

The contents of the header file are used only by this single source file. Move content into .c and remove .h.

Applied to the togreg branch of iio.git and pushed out as testing for the autobuilders to play with it.

Thanks,

Jonathan

One quick note:

The title should include the name of the driver being modified as this is probably the bit interested people are most likely to pick up on in a long list of patches.

I fixed this up. Thanks,

Jonathan

Quoted 315 lines
Quoted 314 lines

---

v2:
-Removing ifndef and define

 drivers/staging/iio/accel/adis16201.h      | 144 -----------------------------
 drivers/staging/iio/accel/adis16201_core.c | 142 +++++++++++++++++++++++++++-
 2 files changed, 141 insertions(+), 145 deletions(-)
 delete mode 100644 drivers/staging/iio/accel/adis16201.h
drivers/staging/iio/accel/adis16201.h deleted +0 -144
deleted file mode 100644
index 64844ad..0000000
@@ -1,144 +0,0 @@
-#ifndef SPI_ADIS16201_H_
-#define SPI_ADIS16201_H_
-
-#define ADIS16201_STARTUP_DELAY	220 /* ms */
-
-/* Flash memory write count */
-#define ADIS16201_FLASH_CNT      0x00
-
-/* Output, power supply */
-#define ADIS16201_SUPPLY_OUT     0x02
-
-/* Output, x-axis accelerometer */
-#define ADIS16201_XACCL_OUT      0x04
-
-/* Output, y-axis accelerometer */
-#define ADIS16201_YACCL_OUT      0x06
-
-/* Output, auxiliary ADC input */
-#define ADIS16201_AUX_ADC        0x08
-
-/* Output, temperature */
-#define ADIS16201_TEMP_OUT       0x0A
-
-/* Output, x-axis inclination */
-#define ADIS16201_XINCL_OUT      0x0C
-
-/* Output, y-axis inclination */
-#define ADIS16201_YINCL_OUT      0x0E
-
-/* Calibration, x-axis acceleration offset */
-#define ADIS16201_XACCL_OFFS     0x10
-
-/* Calibration, y-axis acceleration offset */
-#define ADIS16201_YACCL_OFFS     0x12
-
-/* x-axis acceleration scale factor */
-#define ADIS16201_XACCL_SCALE    0x14
-
-/* y-axis acceleration scale factor */
-#define ADIS16201_YACCL_SCALE    0x16
-
-/* Calibration, x-axis inclination offset */
-#define ADIS16201_XINCL_OFFS     0x18
-
-/* Calibration, y-axis inclination offset */
-#define ADIS16201_YINCL_OFFS     0x1A
-
-/* x-axis inclination scale factor */
-#define ADIS16201_XINCL_SCALE    0x1C
-
-/* y-axis inclination scale factor */
-#define ADIS16201_YINCL_SCALE    0x1E
-
-/* Alarm 1 amplitude threshold */
-#define ADIS16201_ALM_MAG1       0x20
-
-/* Alarm 2 amplitude threshold */
-#define ADIS16201_ALM_MAG2       0x22
-
-/* Alarm 1, sample period */
-#define ADIS16201_ALM_SMPL1      0x24
-
-/* Alarm 2, sample period */
-#define ADIS16201_ALM_SMPL2      0x26
-
-/* Alarm control */
-#define ADIS16201_ALM_CTRL       0x28
-
-/* Auxiliary DAC data */
-#define ADIS16201_AUX_DAC        0x30
-
-/* General-purpose digital input/output control */
-#define ADIS16201_GPIO_CTRL      0x32
-
-/* Miscellaneous control */
-#define ADIS16201_MSC_CTRL       0x34
-
-/* Internal sample period (rate) control */
-#define ADIS16201_SMPL_PRD       0x36
-
-/* Operation, filter configuration */
-#define ADIS16201_AVG_CNT        0x38
-
-/* Operation, sleep mode control */
-#define ADIS16201_SLP_CNT        0x3A
-
-/* Diagnostics, system status register */
-#define ADIS16201_DIAG_STAT      0x3C
-
-/* Operation, system command register */
-#define ADIS16201_GLOB_CMD       0x3E
-
-/* MSC_CTRL */
-
-/* Self-test enable */
-#define ADIS16201_MSC_CTRL_SELF_TEST_EN	        BIT(8)
-
-/* Data-ready enable: 1 = enabled, 0 = disabled */
-#define ADIS16201_MSC_CTRL_DATA_RDY_EN	        BIT(2)
-
-/* Data-ready polarity: 1 = active high, 0 = active low */
-#define ADIS16201_MSC_CTRL_ACTIVE_HIGH	        BIT(1)
-
-/* Data-ready line selection: 1 = DIO1, 0 = DIO0 */
-#define ADIS16201_MSC_CTRL_DATA_RDY_DIO1	BIT(0)
-
-/* DIAG_STAT */
-
-/* Alarm 2 status: 1 = alarm active, 0 = alarm inactive */
-#define ADIS16201_DIAG_STAT_ALARM2        BIT(9)
-
-/* Alarm 1 status: 1 = alarm active, 0 = alarm inactive */
-#define ADIS16201_DIAG_STAT_ALARM1        BIT(8)
-
-/* SPI communications failure */
-#define ADIS16201_DIAG_STAT_SPI_FAIL_BIT   3
-
-/* Flash update failure */
-#define ADIS16201_DIAG_STAT_FLASH_UPT_BIT  2
-
-/* Power supply above 3.625 V */
-#define ADIS16201_DIAG_STAT_POWER_HIGH_BIT 1
-
-/* Power supply below 3.15 V */
-#define ADIS16201_DIAG_STAT_POWER_LOW_BIT  0
-
-/* GLOB_CMD */
-
-#define ADIS16201_GLOB_CMD_SW_RESET	BIT(7)
-#define ADIS16201_GLOB_CMD_FACTORY_CAL	BIT(1)
-
-#define ADIS16201_ERROR_ACTIVE          BIT(14)
-
-enum adis16201_scan {
-	ADIS16201_SCAN_ACC_X,
-	ADIS16201_SCAN_ACC_Y,
-	ADIS16201_SCAN_INCLI_X,
-	ADIS16201_SCAN_INCLI_Y,
-	ADIS16201_SCAN_SUPPLY,
-	ADIS16201_SCAN_AUX_ADC,
-	ADIS16201_SCAN_TEMP,
-};
-
-#endif /* SPI_ADIS16201_H_ */
drivers/staging/iio/accel/adis16201_core.c +141 -1
index 7963d4a..dcf8463 100644
@@ -20,7 +20,147 @@
 #include <linux/iio/buffer.h>
 #include <linux/iio/imu/adis.h>
 
-#include "adis16201.h"
+#define ADIS16201_STARTUP_DELAY	220 /* ms */
+
+/* Flash memory write count */
+#define ADIS16201_FLASH_CNT      0x00
+
+/* Output, power supply */
+#define ADIS16201_SUPPLY_OUT     0x02
+
+/* Output, x-axis accelerometer */
+#define ADIS16201_XACCL_OUT      0x04
+
+/* Output, y-axis accelerometer */
+#define ADIS16201_YACCL_OUT      0x06
+
+/* Output, auxiliary ADC input */
+#define ADIS16201_AUX_ADC        0x08
+
+/* Output, temperature */
+#define ADIS16201_TEMP_OUT       0x0A
+
+/* Output, x-axis inclination */
+#define ADIS16201_XINCL_OUT      0x0C
+
+/* Output, y-axis inclination */
+#define ADIS16201_YINCL_OUT      0x0E
+
+/* Calibration, x-axis acceleration offset */
+#define ADIS16201_XACCL_OFFS     0x10
+
+/* Calibration, y-axis acceleration offset */
+#define ADIS16201_YACCL_OFFS     0x12
+
+/* x-axis acceleration scale factor */
+#define ADIS16201_XACCL_SCALE    0x14
+
+/* y-axis acceleration scale factor */
+#define ADIS16201_YACCL_SCALE    0x16
+
+/* Calibration, x-axis inclination offset */
+#define ADIS16201_XINCL_OFFS     0x18
+
+/* Calibration, y-axis inclination offset */
+#define ADIS16201_YINCL_OFFS     0x1A
+
+/* x-axis inclination scale factor */
+#define ADIS16201_XINCL_SCALE    0x1C
+
+/* y-axis inclination scale factor */
+#define ADIS16201_YINCL_SCALE    0x1E
+
+/* Alarm 1 amplitude threshold */
+#define ADIS16201_ALM_MAG1       0x20
+
+/* Alarm 2 amplitude threshold */
+#define ADIS16201_ALM_MAG2       0x22
+
+/* Alarm 1, sample period */
+#define ADIS16201_ALM_SMPL1      0x24
+
+/* Alarm 2, sample period */
+#define ADIS16201_ALM_SMPL2      0x26
+
+/* Alarm control */
+#define ADIS16201_ALM_CTRL       0x28
+
+/* Auxiliary DAC data */
+#define ADIS16201_AUX_DAC        0x30
+
+/* General-purpose digital input/output control */
+#define ADIS16201_GPIO_CTRL      0x32
+
+/* Miscellaneous control */
+#define ADIS16201_MSC_CTRL       0x34
+
+/* Internal sample period (rate) control */
+#define ADIS16201_SMPL_PRD       0x36
+
+/* Operation, filter configuration */
+#define ADIS16201_AVG_CNT        0x38
+
+/* Operation, sleep mode control */
+#define ADIS16201_SLP_CNT        0x3A
+
+/* Diagnostics, system status register */
+#define ADIS16201_DIAG_STAT      0x3C
+
+/* Operation, system command register */
+#define ADIS16201_GLOB_CMD       0x3E
+
+/* MSC_CTRL */
+
+/* Self-test enable */
+#define ADIS16201_MSC_CTRL_SELF_TEST_EN	        BIT(8)
+
+/* Data-ready enable: 1 = enabled, 0 = disabled */
+#define ADIS16201_MSC_CTRL_DATA_RDY_EN	        BIT(2)
+
+/* Data-ready polarity: 1 = active high, 0 = active low */
+#define ADIS16201_MSC_CTRL_ACTIVE_HIGH	        BIT(1)
+
+/* Data-ready line selection: 1 = DIO1, 0 = DIO0 */
+#define ADIS16201_MSC_CTRL_DATA_RDY_DIO1	BIT(0)
+
+/* DIAG_STAT */
+
+/* Alarm 2 status: 1 = alarm active, 0 = alarm inactive */
+#define ADIS16201_DIAG_STAT_ALARM2        BIT(9)
+
+/* Alarm 1 status: 1 = alarm active, 0 = alarm inactive */
+#define ADIS16201_DIAG_STAT_ALARM1        BIT(8)
+
+/* SPI communications failure */
+#define ADIS16201_DIAG_STAT_SPI_FAIL_BIT   3
+
+/* Flash update failure */
+#define ADIS16201_DIAG_STAT_FLASH_UPT_BIT  2
+
+/* Power supply above 3.625 V */
+#define ADIS16201_DIAG_STAT_POWER_HIGH_BIT 1
+
+/* Power supply below 3.15 V */
+#define ADIS16201_DIAG_STAT_POWER_LOW_BIT  0
+
+/* GLOB_CMD */
+
+#define ADIS16201_GLOB_CMD_SW_RESET	BIT(7)
+#define ADIS16201_GLOB_CMD_FACTORY_CAL	BIT(1)
+
+#define ADIS16201_ERROR_ACTIVE          BIT(14)
+
+enum adis16201_scan {
+	ADIS16201_SCAN_ACC_X,
+	ADIS16201_SCAN_ACC_Y,
+	ADIS16201_SCAN_INCLI_X,
+	ADIS16201_SCAN_INCLI_Y,
+	ADIS16201_SCAN_SUPPLY,
+	ADIS16201_SCAN_AUX_ADC,
+	ADIS16201_SCAN_TEMP,
+};
+
+#endif /* SPI_ADIS16201_H_ */
 
 static const u8 adis16201_addresses[] = {
 	[ADIS16201_SCAN_ACC_X] = ADIS16201_XACCL_OFFS,
#3 lore raw
Quoted 15 lines · Jonathan Cameron
Quoted 11 lines · Jonathan Cameron
Quoted 4 lines · simran singhal

The contents of the header file are used only by this single source file. Move content into .c and remove .h.

Applied to the togreg branch of iio.git and pushed out as testing for the autobuilders to play with it.

Thanks,

Jonathan

One quick note:

Quoted 7 lines

The title should include the name of the driver being modified as this is probably the bit interested people are most likely to pick up on in a long list of patches.

I fixed this up. Thanks,

Jonathan

I have included the name of driver being modified. Due to want me to include the name of file i.e adis16201_core.c

Quoted 316 lines
Quoted 315 lines
Quoted 314 lines

---

v2:
-Removing ifndef and define

 drivers/staging/iio/accel/adis16201.h      | 144 -----------------------------
 drivers/staging/iio/accel/adis16201_core.c | 142 +++++++++++++++++++++++++++-
 2 files changed, 141 insertions(+), 145 deletions(-)
 delete mode 100644 drivers/staging/iio/accel/adis16201.h
drivers/staging/iio/accel/adis16201.h deleted +0 -144
deleted file mode 100644
index 64844ad..0000000
@@ -1,144 +0,0 @@
-#ifndef SPI_ADIS16201_H_
-#define SPI_ADIS16201_H_
-
-#define ADIS16201_STARTUP_DELAY     220 /* ms */
-
-/* Flash memory write count */
-#define ADIS16201_FLASH_CNT      0x00
-
-/* Output, power supply */
-#define ADIS16201_SUPPLY_OUT     0x02
-
-/* Output, x-axis accelerometer */
-#define ADIS16201_XACCL_OUT      0x04
-
-/* Output, y-axis accelerometer */
-#define ADIS16201_YACCL_OUT      0x06
-
-/* Output, auxiliary ADC input */
-#define ADIS16201_AUX_ADC        0x08
-
-/* Output, temperature */
-#define ADIS16201_TEMP_OUT       0x0A
-
-/* Output, x-axis inclination */
-#define ADIS16201_XINCL_OUT      0x0C
-
-/* Output, y-axis inclination */
-#define ADIS16201_YINCL_OUT      0x0E
-
-/* Calibration, x-axis acceleration offset */
-#define ADIS16201_XACCL_OFFS     0x10
-
-/* Calibration, y-axis acceleration offset */
-#define ADIS16201_YACCL_OFFS     0x12
-
-/* x-axis acceleration scale factor */
-#define ADIS16201_XACCL_SCALE    0x14
-
-/* y-axis acceleration scale factor */
-#define ADIS16201_YACCL_SCALE    0x16
-
-/* Calibration, x-axis inclination offset */
-#define ADIS16201_XINCL_OFFS     0x18
-
-/* Calibration, y-axis inclination offset */
-#define ADIS16201_YINCL_OFFS     0x1A
-
-/* x-axis inclination scale factor */
-#define ADIS16201_XINCL_SCALE    0x1C
-
-/* y-axis inclination scale factor */
-#define ADIS16201_YINCL_SCALE    0x1E
-
-/* Alarm 1 amplitude threshold */
-#define ADIS16201_ALM_MAG1       0x20
-
-/* Alarm 2 amplitude threshold */
-#define ADIS16201_ALM_MAG2       0x22
-
-/* Alarm 1, sample period */
-#define ADIS16201_ALM_SMPL1      0x24
-
-/* Alarm 2, sample period */
-#define ADIS16201_ALM_SMPL2      0x26
-
-/* Alarm control */
-#define ADIS16201_ALM_CTRL       0x28
-
-/* Auxiliary DAC data */
-#define ADIS16201_AUX_DAC        0x30
-
-/* General-purpose digital input/output control */
-#define ADIS16201_GPIO_CTRL      0x32
-
-/* Miscellaneous control */
-#define ADIS16201_MSC_CTRL       0x34
-
-/* Internal sample period (rate) control */
-#define ADIS16201_SMPL_PRD       0x36
-
-/* Operation, filter configuration */
-#define ADIS16201_AVG_CNT        0x38
-
-/* Operation, sleep mode control */
-#define ADIS16201_SLP_CNT        0x3A
-
-/* Diagnostics, system status register */
-#define ADIS16201_DIAG_STAT      0x3C
-
-/* Operation, system command register */
-#define ADIS16201_GLOB_CMD       0x3E
-
-/* MSC_CTRL */
-
-/* Self-test enable */
-#define ADIS16201_MSC_CTRL_SELF_TEST_EN             BIT(8)
-
-/* Data-ready enable: 1 = enabled, 0 = disabled */
-#define ADIS16201_MSC_CTRL_DATA_RDY_EN              BIT(2)
-
-/* Data-ready polarity: 1 = active high, 0 = active low */
-#define ADIS16201_MSC_CTRL_ACTIVE_HIGH              BIT(1)
-
-/* Data-ready line selection: 1 = DIO1, 0 = DIO0 */
-#define ADIS16201_MSC_CTRL_DATA_RDY_DIO1    BIT(0)
-
-/* DIAG_STAT */
-
-/* Alarm 2 status: 1 = alarm active, 0 = alarm inactive */
-#define ADIS16201_DIAG_STAT_ALARM2        BIT(9)
-
-/* Alarm 1 status: 1 = alarm active, 0 = alarm inactive */
-#define ADIS16201_DIAG_STAT_ALARM1        BIT(8)
-
-/* SPI communications failure */
-#define ADIS16201_DIAG_STAT_SPI_FAIL_BIT   3
-
-/* Flash update failure */
-#define ADIS16201_DIAG_STAT_FLASH_UPT_BIT  2
-
-/* Power supply above 3.625 V */
-#define ADIS16201_DIAG_STAT_POWER_HIGH_BIT 1
-
-/* Power supply below 3.15 V */
-#define ADIS16201_DIAG_STAT_POWER_LOW_BIT  0
-
-/* GLOB_CMD */
-
-#define ADIS16201_GLOB_CMD_SW_RESET BIT(7)
-#define ADIS16201_GLOB_CMD_FACTORY_CAL      BIT(1)
-
-#define ADIS16201_ERROR_ACTIVE          BIT(14)
-
-enum adis16201_scan {
-    ADIS16201_SCAN_ACC_X,
-    ADIS16201_SCAN_ACC_Y,
-    ADIS16201_SCAN_INCLI_X,
-    ADIS16201_SCAN_INCLI_Y,
-    ADIS16201_SCAN_SUPPLY,
-    ADIS16201_SCAN_AUX_ADC,
-    ADIS16201_SCAN_TEMP,
-};
-
-#endif /* SPI_ADIS16201_H_ */
drivers/staging/iio/accel/adis16201_core.c +141 -1
index 7963d4a..dcf8463 100644
@@ -20,7 +20,147 @@
 #include <linux/iio/buffer.h>
 #include <linux/iio/imu/adis.h>
 
-#include "adis16201.h"
+#define ADIS16201_STARTUP_DELAY     220 /* ms */
+
+/* Flash memory write count */
+#define ADIS16201_FLASH_CNT      0x00
+
+/* Output, power supply */
+#define ADIS16201_SUPPLY_OUT     0x02
+
+/* Output, x-axis accelerometer */
+#define ADIS16201_XACCL_OUT      0x04
+
+/* Output, y-axis accelerometer */
+#define ADIS16201_YACCL_OUT      0x06
+
+/* Output, auxiliary ADC input */
+#define ADIS16201_AUX_ADC        0x08
+
+/* Output, temperature */
+#define ADIS16201_TEMP_OUT       0x0A
+
+/* Output, x-axis inclination */
+#define ADIS16201_XINCL_OUT      0x0C
+
+/* Output, y-axis inclination */
+#define ADIS16201_YINCL_OUT      0x0E
+
+/* Calibration, x-axis acceleration offset */
+#define ADIS16201_XACCL_OFFS     0x10
+
+/* Calibration, y-axis acceleration offset */
+#define ADIS16201_YACCL_OFFS     0x12
+
+/* x-axis acceleration scale factor */
+#define ADIS16201_XACCL_SCALE    0x14
+
+/* y-axis acceleration scale factor */
+#define ADIS16201_YACCL_SCALE    0x16
+
+/* Calibration, x-axis inclination offset */
+#define ADIS16201_XINCL_OFFS     0x18
+
+/* Calibration, y-axis inclination offset */
+#define ADIS16201_YINCL_OFFS     0x1A
+
+/* x-axis inclination scale factor */
+#define ADIS16201_XINCL_SCALE    0x1C
+
+/* y-axis inclination scale factor */
+#define ADIS16201_YINCL_SCALE    0x1E
+
+/* Alarm 1 amplitude threshold */
+#define ADIS16201_ALM_MAG1       0x20
+
+/* Alarm 2 amplitude threshold */
+#define ADIS16201_ALM_MAG2       0x22
+
+/* Alarm 1, sample period */
+#define ADIS16201_ALM_SMPL1      0x24
+
+/* Alarm 2, sample period */
+#define ADIS16201_ALM_SMPL2      0x26
+
+/* Alarm control */
+#define ADIS16201_ALM_CTRL       0x28
+
+/* Auxiliary DAC data */
+#define ADIS16201_AUX_DAC        0x30
+
+/* General-purpose digital input/output control */
+#define ADIS16201_GPIO_CTRL      0x32
+
+/* Miscellaneous control */
+#define ADIS16201_MSC_CTRL       0x34
+
+/* Internal sample period (rate) control */
+#define ADIS16201_SMPL_PRD       0x36
+
+/* Operation, filter configuration */
+#define ADIS16201_AVG_CNT        0x38
+
+/* Operation, sleep mode control */
+#define ADIS16201_SLP_CNT        0x3A
+
+/* Diagnostics, system status register */
+#define ADIS16201_DIAG_STAT      0x3C
+
+/* Operation, system command register */
+#define ADIS16201_GLOB_CMD       0x3E
+
+/* MSC_CTRL */
+
+/* Self-test enable */
+#define ADIS16201_MSC_CTRL_SELF_TEST_EN             BIT(8)
+
+/* Data-ready enable: 1 = enabled, 0 = disabled */
+#define ADIS16201_MSC_CTRL_DATA_RDY_EN              BIT(2)
+
+/* Data-ready polarity: 1 = active high, 0 = active low */
+#define ADIS16201_MSC_CTRL_ACTIVE_HIGH              BIT(1)
+
+/* Data-ready line selection: 1 = DIO1, 0 = DIO0 */
+#define ADIS16201_MSC_CTRL_DATA_RDY_DIO1    BIT(0)
+
+/* DIAG_STAT */
+
+/* Alarm 2 status: 1 = alarm active, 0 = alarm inactive */
+#define ADIS16201_DIAG_STAT_ALARM2        BIT(9)
+
+/* Alarm 1 status: 1 = alarm active, 0 = alarm inactive */
+#define ADIS16201_DIAG_STAT_ALARM1        BIT(8)
+
+/* SPI communications failure */
+#define ADIS16201_DIAG_STAT_SPI_FAIL_BIT   3
+
+/* Flash update failure */
+#define ADIS16201_DIAG_STAT_FLASH_UPT_BIT  2
+
+/* Power supply above 3.625 V */
+#define ADIS16201_DIAG_STAT_POWER_HIGH_BIT 1
+
+/* Power supply below 3.15 V */
+#define ADIS16201_DIAG_STAT_POWER_LOW_BIT  0
+
+/* GLOB_CMD */
+
+#define ADIS16201_GLOB_CMD_SW_RESET BIT(7)
+#define ADIS16201_GLOB_CMD_FACTORY_CAL      BIT(1)
+
+#define ADIS16201_ERROR_ACTIVE          BIT(14)
+
+enum adis16201_scan {
+    ADIS16201_SCAN_ACC_X,
+    ADIS16201_SCAN_ACC_Y,
+    ADIS16201_SCAN_INCLI_X,
+    ADIS16201_SCAN_INCLI_Y,
+    ADIS16201_SCAN_SUPPLY,
+    ADIS16201_SCAN_AUX_ADC,
+    ADIS16201_SCAN_TEMP,
+};
+
+#endif /* SPI_ADIS16201_H_ */
 
 static const u8 adis16201_addresses[] = {
     [ADIS16201_SCAN_ACC_X] = ADIS16201_XACCL_OFFS,
#4 lore raw
Quoted 20 lines · SIMRAN SINGHAL
Quoted 19 lines · Jonathan Cameron
Quoted 11 lines · Jonathan Cameron
Quoted 4 lines · simran singhal

The contents of the header file are used only by this single source file. Move content into .c and remove .h.

Applied to the togreg branch of iio.git and pushed out as testing for the autobuilders to play with it.

Thanks,

Jonathan

One quick note:

The title should include the name of the driver being modified as this is probably the bit interested people are most likely to pick up on in a long list of patches.

Quoted 6 lines
Quoted 3 lines

I fixed this up. Thanks,

Jonathan

I have included the name of driver being modified. Due to want me to include the name of file i.e adis16201_core.c

Not the full filename, but the partnumber. E.g.

	'staging: iio: adis16201: ...'
#5 lore raw
Quoted 23 lines · Lars-Peter Clausen
Quoted 22 lines · SIMRAN SINGHAL
Quoted 21 lines · Jonathan Cameron
Quoted 11 lines · Jonathan Cameron
Quoted 4 lines · simran singhal

The contents of the header file are used only by this single source file. Move content into .c and remove .h.

Applied to the togreg branch of iio.git and pushed out as testing for the autobuilders to play with it.

Thanks,

Jonathan

One quick note:

The title should include the name of the driver being modified as this is probably the bit interested people are most likely to pick up on in a long list of patches.

I fixed this up. Thanks,

Quoted 9 lines
Quoted 4 lines
Quoted 1 line

Jonathan

I have included the name of driver being modified. Due to want me to include the name of file i.e adis16201_core.c

Not the full filename, but the partnumber. E.g.

        'staging: iio: adis16201: ...'

Lars-Peter, I got it.

Jonathan, I got my mistake should I send v3.