Skip to contentSkip to conversation

net: phy: make phy_package a separate module

PATCH Applied Heiner Kallweit 2 participants 5 messages Jun 12, 2025 – Jun 16, 2025

Subsystems (5)
lore
Share & tools
lore

Heiner Kallweit

author maintainer
#0 lore raw

cover net: phy: make phy_package a separate module

Only a handful of PHY drivers needs the PHY package functionality, therefore make it a separate module which is built only if needed.

Heiner Kallweit (3):
net: phy: move __phy_package_[read|write]_mmd to phy_package.c
net: phy: make phy_package a separate module
net: phy: add Kconfig symbol PHY_PACKAGE

 drivers/net/phy/Kconfig           |  6 +++
 drivers/net/phy/Makefile          |  3 +-
 drivers/net/phy/mediatek/Kconfig  |  1 +
 drivers/net/phy/phy-core.c        | 75 +++----------------------------
 drivers/net/phy/phy_package.c     | 71 ++++++++++++++++++++++++++++-
 drivers/net/phy/phylib-internal.h |  6 ++-
 drivers/net/phy/qcom/Kconfig      |  1 +
 7 files changed, 91 insertions(+), 72 deletions(-)
Signature · 1 line
2.49.0
author maintainer
#1 lore raw

PATCH 1/3 net: phy: move __phy_package_[read|write]_mmd to phy_package.c

Move both functions to phy_package.c, so that phy_core.c no longer has a dependency on phy_package.c (phy_package_address).

---
 drivers/net/phy/phy-core.c        | 75 +++----------------------------
 drivers/net/phy/phy_package.c     | 68 +++++++++++++++++++++++++++-
 drivers/net/phy/phylib-internal.h |  6 ++-
 3 files changed, 78 insertions(+), 71 deletions(-)
drivers/net/phy/phy-core.c +6 -69
index e177037f9..27f183356 100644
@@ -375,8 +375,8 @@ static void mmd_phy_indirect(struct mii_bus *bus, int phy_addr, int devad,
 			devad | MII_MMD_CTRL_NOINCR);
 }
 
-static int mmd_phy_read(struct mii_bus *bus, int phy_addr, bool is_c45,
-			int devad, u32 regnum)
+int mmd_phy_read(struct mii_bus *bus, int phy_addr, bool is_c45,
+		 int devad, u32 regnum)
 {
 	if (is_c45)
 		return __mdiobus_c45_read(bus, phy_addr, devad, regnum);
@@ -385,9 +385,10 @@ static int mmd_phy_read(struct mii_bus *bus, int phy_addr, bool is_c45,
 	/* Read the content of the MMD's selected register */
 	return __mdiobus_read(bus, phy_addr, MII_MMD_DATA);
 }
+EXPORT_SYMBOL_GPL(mmd_phy_read);
 
-static int mmd_phy_write(struct mii_bus *bus, int phy_addr, bool is_c45,
-			 int devad, u32 regnum, u16 val)
+int mmd_phy_write(struct mii_bus *bus, int phy_addr, bool is_c45,
+		  int devad, u32 regnum, u16 val)
 {
 	if (is_c45)
 		return __mdiobus_c45_write(bus, phy_addr, devad, regnum, val);
@@ -396,6 +397,7 @@ static int mmd_phy_write(struct mii_bus *bus, int phy_addr, bool is_c45,
 	/* Write the data into MMD's selected register */
 	return __mdiobus_write(bus, phy_addr, MII_MMD_DATA, val);
 }
+EXPORT_SYMBOL_GPL(mmd_phy_write);
 
 /**
  * __phy_read_mmd - Convenience function for reading a register
@@ -485,71 +487,6 @@ int phy_write_mmd(struct phy_device *phydev, int devad, u32 regnum, u16 val)
 }
 EXPORT_SYMBOL(phy_write_mmd);
 
-/**
- * __phy_package_read_mmd - read MMD reg relative to PHY package base addr
- * @phydev: The phy_device struct
- * @addr_offset: The offset to be added to PHY package base_addr
- * @devad: The MMD to read from
- * @regnum: The register on the MMD to read
- *
- * Convenience helper for reading a register of an MMD on a given PHY
- * using the PHY package base address. The base address is added to
- * the addr_offset value.
- *
- * Same calling rules as for __phy_read();
- *
- * NOTE: It's assumed that the entire PHY package is either C22 or C45.
- */
-int __phy_package_read_mmd(struct phy_device *phydev,
-			   unsigned int addr_offset, int devad,
-			   u32 regnum)
-{
-	int addr = phy_package_address(phydev, addr_offset);
-
-	if (addr < 0)
-		return addr;
-
-	if (regnum > (u16)~0 || devad > 32)
-		return -EINVAL;
-
-	return mmd_phy_read(phydev->mdio.bus, addr, phydev->is_c45, devad,
-			    regnum);
-}
-EXPORT_SYMBOL(__phy_package_read_mmd);
-
-/**
- * __phy_package_write_mmd - write MMD reg relative to PHY package base addr
- * @phydev: The phy_device struct
- * @addr_offset: The offset to be added to PHY package base_addr
- * @devad: The MMD to write to
- * @regnum: The register on the MMD to write
- * @val: value to write to @regnum
- *
- * Convenience helper for writing a register of an MMD on a given PHY
- * using the PHY package base address. The base address is added to
- * the addr_offset value.
- *
- * Same calling rules as for __phy_write();
- *
- * NOTE: It's assumed that the entire PHY package is either C22 or C45.
- */
-int __phy_package_write_mmd(struct phy_device *phydev,
-			    unsigned int addr_offset, int devad,
-			    u32 regnum, u16 val)
-{
-	int addr = phy_package_address(phydev, addr_offset);
-
-	if (addr < 0)
-		return addr;
-
-	if (regnum > (u16)~0 || devad > 32)
-		return -EINVAL;
-
-	return mmd_phy_write(phydev->mdio.bus, addr, phydev->is_c45, devad,
-			     regnum, val);
-}
-EXPORT_SYMBOL(__phy_package_write_mmd);
-
 /**
  * phy_modify_changed - Function for modifying a PHY register
  * @phydev: the phy_device struct
drivers/net/phy/phy_package.c +67 -1

80 lines not on this page · raw message

drivers/net/phy/phylib-internal.h +5 -1
index afac2bd15..ebda74eb6 100644
@@ -7,6 +7,7 @@
 #define __PHYLIB_INTERNAL_H
 
 struct phy_device;
+struct mii_bus;
 
 /*
  * phy_supported_speeds - return all speeds currently supported by a PHY device
@@ -20,7 +21,10 @@ void of_set_phy_timing_role(struct phy_device *phydev);
 int phy_speed_down_core(struct phy_device *phydev);
 void phy_check_downshift(struct phy_device *phydev);
 
-int phy_package_address(struct phy_device *phydev, unsigned int addr_offset);
+int mmd_phy_read(struct mii_bus *bus, int phy_addr, bool is_c45,
+		 int devad, u32 regnum);
+int mmd_phy_write(struct mii_bus *bus, int phy_addr, bool is_c45,
+		  int devad, u32 regnum, u16 val);
 
 int genphy_c45_read_eee_adv(struct phy_device *phydev, unsigned long *adv);
 
Signature · 1 line
2.49.0
author maintainer
#2 lore raw

PATCH 2/3 net: phy: make phy_package a separate module

In reply to Heiner Kallweit

Make phy_package a separate module, so that this code is only loaded if needed.

---
 drivers/net/phy/Makefile      | 3 ++-
 drivers/net/phy/phy_package.c | 3 +++
 2 files changed, 5 insertions(+), 1 deletion(-)
drivers/net/phy/Makefile +2 -1
index 7827609e9..4e69597f2 100644
@@ -3,7 +3,7 @@
 
 libphy-y			:= phy.o phy-c45.o phy-core.o phy_device.o \
 				   linkmode.o phy_link_topology.o \
-				   phy_package.o phy_caps.o mdio_bus_provider.o
+				   phy_caps.o mdio_bus_provider.o
 mdio-bus-y			+= mdio_bus.o mdio_device.o
 
 ifdef CONFIG_PHYLIB
@@ -19,6 +19,7 @@ obj-$(CONFIG_MDIO_BUS)		+= mdio-bus.o
 obj-$(CONFIG_PHYLINK)		+= phylink.o
 obj-$(CONFIG_PHYLIB)		+= libphy.o
 obj-$(CONFIG_PHYLIB)		+= mdio_devres.o
+obj-$(CONFIG_PHYLIB)		+= phy_package.o
 
 obj-$(CONFIG_NETWORK_PHY_TIMESTAMPING) += mii_timestamper.o
 
drivers/net/phy/phy_package.c +3 -0
index 5dd5db7e8..3024da0bb 100644
@@ -414,3 +414,6 @@ int devm_of_phy_package_join(struct device *dev, struct phy_device *phydev,
 	return ret;
 }
 EXPORT_SYMBOL_GPL(devm_of_phy_package_join);
+
+MODULE_DESCRIPTION("PHY package support");
+MODULE_LICENSE("GPL");
Signature · 1 line
2.49.0
author maintainer
#3 lore raw

PATCH 3/3 net: phy: add Kconfig symbol PHY_PACKAGE

In reply to Heiner Kallweit

Only a handful of PHY drivers needs the PHY package functionality, therefore build the module only if needed.

---
 drivers/net/phy/Kconfig          | 6 ++++++
 drivers/net/phy/Makefile         | 2 +-
 drivers/net/phy/mediatek/Kconfig | 1 +
 drivers/net/phy/qcom/Kconfig     | 1 +
 4 files changed, 9 insertions(+), 1 deletion(-)
drivers/net/phy/Kconfig +6 -0
index 53dad2482..28acc6392 100644
@@ -25,6 +25,9 @@ if PHYLIB
 config SWPHY
 	bool
 
+config PHY_PACKAGE
+	 tristate
+
 config LED_TRIGGER_PHY
 	bool "Support LED triggers for tracking link state"
 	depends on LEDS_TRIGGERS
@@ -157,6 +160,7 @@ config BCM54140_PHY
 	tristate "Broadcom BCM54140 PHY"
 	depends on HWMON || HWMON=n
 	select BCM_NET_PHYLIB
+	select PHY_PACKAGE
 	help
 	  Support the Broadcom BCM54140 Quad SGMII/QSGMII PHY.
 
@@ -292,6 +296,7 @@ source "drivers/net/phy/mediatek/Kconfig"
 config MICREL_PHY
 	tristate "Micrel PHYs"
 	depends on PTP_1588_CLOCK_OPTIONAL
+	select PHY_PACKAGE
 	help
 	  Supports the KSZ9021, VSC8201, KS8001 PHYs.
 
@@ -323,6 +328,7 @@ config MICROSEMI_PHY
 	depends on MACSEC || MACSEC=n
 	depends on PTP_1588_CLOCK_OPTIONAL || !NETWORK_PHY_TIMESTAMPING
 	select CRYPTO_LIB_AES if MACSEC
+	select PHY_PACKAGE
 	help
 	  Currently supports VSC8514, VSC8530, VSC8531, VSC8540 and VSC8541 PHYs
 
drivers/net/phy/Makefile +1 -1
index 4e69597f2..b4795aaf9 100644
@@ -19,7 +19,7 @@ obj-$(CONFIG_MDIO_BUS)		+= mdio-bus.o
 obj-$(CONFIG_PHYLINK)		+= phylink.o
 obj-$(CONFIG_PHYLIB)		+= libphy.o
 obj-$(CONFIG_PHYLIB)		+= mdio_devres.o
-obj-$(CONFIG_PHYLIB)		+= phy_package.o
+obj-$(CONFIG_PHY_PACKAGE)	+= phy_package.o
 
 obj-$(CONFIG_NETWORK_PHY_TIMESTAMPING) += mii_timestamper.o
 
drivers/net/phy/mediatek/Kconfig +1 -0
index 9f30a91be..bb7dc8762 100644
@@ -27,6 +27,7 @@ config MEDIATEK_GE_SOC_PHY
 	depends on ARCH_AIROHA || (ARCH_MEDIATEK && NVMEM_MTK_EFUSE) || \
 		   COMPILE_TEST
 	select MTK_NET_PHYLIB
+	select PHY_PACKAGE
 	help
 	  Supports MediaTek SoC built-in Gigabit Ethernet PHYs.
 
drivers/net/phy/qcom/Kconfig +1 -0
index 570626cc8..bba14be8d 100644
@@ -24,6 +24,7 @@ config QCA808X_PHY
 config QCA807X_PHY
 	tristate "Qualcomm QCA807x PHYs"
 	select QCOM_NET_PHYLIB
+	select PHY_PACKAGE
 	depends on OF_MDIO
 	help
 	  Currently supports the Qualcomm QCA8072, QCA8075 and the PSGMII
Signature · 1 line
2.49.0
#4 lore raw
In reply to Heiner Kallweit
This series was applied to netdev/net-next.git (main) by Jakub Kicinski <[email protected]>:

Hello:

This series was applied to netdev/net-next.git (main) by Jakub Kicinski <[email protected]>:

Quoted 9 lines · On Thu, 12 Jun 2025 23:25:00 +0200 you wrote:

Only a handful of PHY drivers needs the PHY package functionality, therefore make it a separate module which is built only if needed.

Heiner Kallweit (3):
net: phy: move __phy_package_[read|write]_mmd to phy_package.c
net: phy: make phy_package a separate module
net: phy: add Kconfig symbol PHY_PACKAGE

[...]

Here is the summary with links:
- [net-next,1/3] net: phy: move __phy_package_[read|write]_mmd to phy_package.c

    https://git.kernel.org/netdev/net-next/c/cbd1ab0ce8f6
  - [net-next,2/3] net: phy: make phy_package a separate module
    https://git.kernel.org/netdev/net-next/c/a1acde1e1bcf
  - [net-next,3/3] net: phy: add Kconfig symbol PHY_PACKAGE
    https://git.kernel.org/netdev/net-next/c/7d57386905d4

You are awesome, thank you!

Signature · 2 lines
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html