Skip to contentSkip to conversation

dt-bindings: sdhci-of-at91: new compatible string and update properties

PATCH Superseded Ludovic Desroches 2 participants 6 messages Oct 25, 2019 – Nov 26, 2019

Subsystems (5)

v3 of 4 Superseded Latest is v4 →

lore
Share & tools
lore
#0 lore raw

PATCH v3 1/3 dt-bindings: sdhci-of-at91: new compatible string and update properties

There is a new compatible string for the SAM9X60 sdhci device. It involves an update of the properties about the clocks stuff.

---

Changes:
- v3: rebase due to conflict with Nicolas' patch
- v2: remove the extra example and fix node label

 .../devicetree/bindings/mmc/sdhci-atmel.txt         | 13 ++++++++++---
 1 file changed, 10 insertions(+), 3 deletions(-)
Documentation/devicetree/bindings/mmc/sdhci-atmel.txt +10 -3
index 503c6dbac1b2..69edfd4d3922 100644
@@ -5,11 +5,16 @@ Documentation/devicetree/bindings/mmc/mmc.txt and the properties used by the
 sdhci-of-at91 driver.
 
 Required properties:
-- compatible:		Must be "atmel,sama5d2-sdhci".
+- compatible:		Must be "atmel,sama5d2-sdhci" or "microchip,sam9x60-sdhci".
 - clocks:		Phandlers to the clocks.
-- clock-names:		Must be "hclock", "multclk", "baseclk";
+- clock-names:		Must be "hclock", "multclk", "baseclk" for
+			"atmel,sama5d2-sdhci".
+			Must be "hclock", "multclk" for "microchip,sam9x60-sdhci".
 
 Optional properties:
+- assigned-clocks:	The same with "multclk".
+- assigned-clock-rates	The rate of "multclk" in order to not rely on the
+			gck configuration set by previous components.
 - microchip,sdcal-inverted: when present, polarity on the SDCAL SoC pin is
   inverted. The default polarity for this signal is described in the datasheet.
   For instance on SAMA5D2, the pin is usually tied to the GND with a resistor
@@ -17,10 +22,12 @@ Optional properties:
 
 Example:
 
-sdmmc0: sdio-host@a0000000 {
+mmc0: sdio-host@a0000000 {
 	compatible = "atmel,sama5d2-sdhci";
 	reg = <0xa0000000 0x300>;
 	interrupts = <31 IRQ_TYPE_LEVEL_HIGH 0>;
 	clocks = <&sdmmc0_hclk>, <&sdmmc0_gclk>, <&main>;
 	clock-names = "hclock", "multclk", "baseclk";
+	assigned-clocks = <&sdmmc0_gclk>;
+	assigned-clock-rates = <480000000>;
 };
Signature · 1 line
2.24.0.rc0
#1 lore raw

PATCH v3 2/3 mmc: sdhci-of-at91: rework clocks management to support SAM9x60 device

In the SAM9x60 SoC, there are only two clocks instead of three for the SDHCI device. The base clk is no longer provided, it is generated internally from the mult clk.

The values of the base clk and mul in the capabilities registers may not reflect the reality as the mult clk is a programmable clock which can take several rates. As we can't trust those values, take them from the clock tree and update the capabilities according to.

As we can have the same pitfall, in some cases, with the SAMA5D2 Soc, stop relying on capabilities too.

---

Changes:
- v3: none
- v2: none

 drivers/mmc/host/sdhci-of-at91.c | 105 +++++++++++++++++--------------
 1 file changed, 58 insertions(+), 47 deletions(-)
drivers/mmc/host/sdhci-of-at91.c +58 -47
index 9571c4a882a9..7477471dac00 100644
@@ -33,7 +33,14 @@
 
 #define SDHCI_AT91_PRESET_COMMON_CONF	0x400 /* drv type B, programmable clock mode */
 
+struct sdhci_at91_soc_data {
+	const struct sdhci_pltfm_data *pdata;
+	bool baseclk_is_generated_internally;
+	unsigned int divider_for_baseclk;
+};
+
 struct sdhci_at91_priv {
+	const struct sdhci_at91_soc_data *soc_data;
 	struct clk *hclock;
 	struct clk *gck;
 	struct clk *mainck;
@@ -141,12 +148,24 @@ static const struct sdhci_ops sdhci_at91_sama5d2_ops = {
 	.set_power		= sdhci_at91_set_power,
 };
 
-static const struct sdhci_pltfm_data soc_data_sama5d2 = {
+static const struct sdhci_pltfm_data sdhci_sama5d2_pdata = {
 	.ops = &sdhci_at91_sama5d2_ops,
 };
 
+static const struct sdhci_at91_soc_data soc_data_sama5d2 = {
+	.pdata = &sdhci_sama5d2_pdata,
+	.baseclk_is_generated_internally = false,
+};
+
+static const struct sdhci_at91_soc_data soc_data_sam9x60 = {
+	.pdata = &sdhci_sama5d2_pdata,
+	.baseclk_is_generated_internally = true,
+	.divider_for_baseclk = 2,
+};
+
 static const struct of_device_id sdhci_at91_dt_match[] = {
 	{ .compatible = "atmel,sama5d2-sdhci", .data = &soc_data_sama5d2 },
+	{ .compatible = "microchip,sam9x60-sdhci", .data = &soc_data_sam9x60 },
 	{}
 };
 MODULE_DEVICE_TABLE(of, sdhci_at91_dt_match);
@@ -156,50 +175,37 @@ static int sdhci_at91_set_clks_presets(struct device *dev)
 	struct sdhci_host *host = dev_get_drvdata(dev);
 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 	struct sdhci_at91_priv *priv = sdhci_pltfm_priv(pltfm_host);
-	int ret;
 	unsigned int			caps0, caps1;
 	unsigned int			clk_base, clk_mul;
-	unsigned int			gck_rate, real_gck_rate;
+	unsigned int			gck_rate, clk_base_rate;
 	unsigned int			preset_div;
 
-	/*
-	 * The mult clock is provided by as a generated clock by the PMC
-	 * controller. In order to set the rate of gck, we have to get the
-	 * base clock rate and the clock mult from capabilities.
-	 */
 	clk_prepare_enable(priv->hclock);
 	caps0 = readl(host->ioaddr + SDHCI_CAPABILITIES);
 	caps1 = readl(host->ioaddr + SDHCI_CAPABILITIES_1);
-	clk_base = (caps0 & SDHCI_CLOCK_V3_BASE_MASK) >> SDHCI_CLOCK_BASE_SHIFT;
-	clk_mul = (caps1 & SDHCI_CLOCK_MUL_MASK) >> SDHCI_CLOCK_MUL_SHIFT;
-	gck_rate = clk_base * 1000000 * (clk_mul + 1);
-	ret = clk_set_rate(priv->gck, gck_rate);
-	if (ret < 0) {
-		dev_err(dev, "failed to set gck");
-		clk_disable_unprepare(priv->hclock);
-		return ret;
-	}
-	/*
-	 * We need to check if we have the requested rate for gck because in
-	 * some cases this rate could be not supported. If it happens, the rate
-	 * is the closest one gck can provide. We have to update the value
-	 * of clk mul.
-	 */
-	real_gck_rate = clk_get_rate(priv->gck);
-	if (real_gck_rate != gck_rate) {
-		clk_mul = real_gck_rate / (clk_base * 1000000) - 1;
-		caps1 &= (~SDHCI_CLOCK_MUL_MASK);
-		caps1 |= ((clk_mul << SDHCI_CLOCK_MUL_SHIFT) &
-			  SDHCI_CLOCK_MUL_MASK);
-		/* Set capabilities in r/w mode. */
-		writel(SDMMC_CACR_KEY | SDMMC_CACR_CAPWREN,
-		       host->ioaddr + SDMMC_CACR);
-		writel(caps1, host->ioaddr + SDHCI_CAPABILITIES_1);
-		/* Set capabilities in ro mode. */
-		writel(0, host->ioaddr + SDMMC_CACR);
-		dev_info(dev, "update clk mul to %u as gck rate is %u Hz\n",
-			 clk_mul, real_gck_rate);
-	}
+
+	gck_rate = clk_get_rate(priv->gck);
+	if (priv->soc_data->baseclk_is_generated_internally)
+		clk_base_rate = gck_rate / priv->soc_data->divider_for_baseclk;
+	else
+		clk_base_rate = clk_get_rate(priv->mainck);
+
+	clk_base = clk_base_rate / 1000000;
+	clk_mul = gck_rate / clk_base_rate - 1;
+
+	caps0 &= (~SDHCI_CLOCK_V3_BASE_MASK);
+	caps0 |= ((clk_base << SDHCI_CLOCK_BASE_SHIFT) & SDHCI_CLOCK_V3_BASE_MASK);
+	caps1 &= (~SDHCI_CLOCK_MUL_MASK);
+	caps1 |= ((clk_mul << SDHCI_CLOCK_MUL_SHIFT) & SDHCI_CLOCK_MUL_MASK);
+	/* Set capabilities in r/w mode. */
+	writel(SDMMC_CACR_KEY | SDMMC_CACR_CAPWREN, host->ioaddr + SDMMC_CACR);
+	writel(caps0, host->ioaddr + SDHCI_CAPABILITIES_1);
+	writel(caps1, host->ioaddr + SDHCI_CAPABILITIES_1);
+	/* Set capabilities in ro mode. */
+	writel(0, host->ioaddr + SDMMC_CACR);
+
+	dev_info(dev, "update clk mul to %u as gck rate is %u Hz and clk base is %u Hz\n",
+		 clk_mul, gck_rate, clk_base_rate);
 
 	/*
 	 * We have to set preset values because it depends on the clk_mul
@@ -207,19 +213,19 @@ static int sdhci_at91_set_clks_presets(struct device *dev)
 	 * maximum sd clock value is 120 MHz instead of 208 MHz. For that
 	 * reason, we need to use presets to support SDR104.
 	 */
-	preset_div = DIV_ROUND_UP(real_gck_rate, 24000000) - 1;
+	preset_div = DIV_ROUND_UP(gck_rate, 24000000) - 1;
 	writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
 	       host->ioaddr + SDHCI_PRESET_FOR_SDR12);
-	preset_div = DIV_ROUND_UP(real_gck_rate, 50000000) - 1;
+	preset_div = DIV_ROUND_UP(gck_rate, 50000000) - 1;
 	writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
 	       host->ioaddr + SDHCI_PRESET_FOR_SDR25);
-	preset_div = DIV_ROUND_UP(real_gck_rate, 100000000) - 1;
+	preset_div = DIV_ROUND_UP(gck_rate, 100000000) - 1;
 	writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
 	       host->ioaddr + SDHCI_PRESET_FOR_SDR50);
-	preset_div = DIV_ROUND_UP(real_gck_rate, 120000000) - 1;
+	preset_div = DIV_ROUND_UP(gck_rate, 120000000) - 1;
 	writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
 	       host->ioaddr + SDHCI_PRESET_FOR_SDR104);
-	preset_div = DIV_ROUND_UP(real_gck_rate, 50000000) - 1;
+	preset_div = DIV_ROUND_UP(gck_rate, 50000000) - 1;
 	writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
 	       host->ioaddr + SDHCI_PRESET_FOR_DDR50);
 
@@ -314,7 +320,7 @@ static const struct dev_pm_ops sdhci_at91_dev_pm_ops = {
 static int sdhci_at91_probe(struct platform_device *pdev)
 {
 	const struct of_device_id	*match;
-	const struct sdhci_pltfm_data	*soc_data;
+	const struct sdhci_at91_soc_data	*soc_data;
 	struct sdhci_host		*host;
 	struct sdhci_pltfm_host		*pltfm_host;
 	struct sdhci_at91_priv		*priv;
@@ -325,17 +331,22 @@ static int sdhci_at91_probe(struct platform_device *pdev)
 		return -EINVAL;
 	soc_data = match->data;
 
-	host = sdhci_pltfm_init(pdev, soc_data, sizeof(*priv));
+	host = sdhci_pltfm_init(pdev, soc_data->pdata, sizeof(*priv));
 	if (IS_ERR(host))
 		return PTR_ERR(host);
 
 	pltfm_host = sdhci_priv(host);
 	priv = sdhci_pltfm_priv(pltfm_host);
+	priv->soc_data = soc_data;
 
 	priv->mainck = devm_clk_get(&pdev->dev, "baseclk");
 	if (IS_ERR(priv->mainck)) {
-		dev_err(&pdev->dev, "failed to get baseclk\n");
-		return PTR_ERR(priv->mainck);
+		if (soc_data->baseclk_is_generated_internally) {
+			priv->mainck = NULL;
+		} else {
+			dev_err(&pdev->dev, "failed to get baseclk\n");
+			return PTR_ERR(priv->mainck);
+		}
 	}
 
 	priv->hclock = devm_clk_get(&pdev->dev, "hclock");
Signature · 1 line
2.24.0.rc0
maintainer
#2 lore raw

Re: [PATCH v3 2/3] mmc: sdhci-of-at91: rework clocks management to support SAM9x60 device

Quoted 123 lines · Ludovic Desroches

In the SAM9x60 SoC, there are only two clocks instead of three for the SDHCI device. The base clk is no longer provided, it is generated internally from the mult clk.

The values of the base clk and mul in the capabilities registers may not reflect the reality as the mult clk is a programmable clock which can take several rates. As we can't trust those values, take them from the clock tree and update the capabilities according to.

As we can have the same pitfall, in some cases, with the SAMA5D2 Soc, stop relying on capabilities too.

---

Changes:
- v3: none
- v2: none

 drivers/mmc/host/sdhci-of-at91.c | 105 +++++++++++++++++--------------
 1 file changed, 58 insertions(+), 47 deletions(-)
drivers/mmc/host/sdhci-of-at91.c +28 -38
index 9571c4a882a9..7477471dac00 100644
@@ -33,7 +33,14 @@
 
 #define SDHCI_AT91_PRESET_COMMON_CONF	0x400 /* drv type B, programmable clock mode */
 
+struct sdhci_at91_soc_data {
+	const struct sdhci_pltfm_data *pdata;
+	bool baseclk_is_generated_internally;
+	unsigned int divider_for_baseclk;
+};
+
 struct sdhci_at91_priv {
+	const struct sdhci_at91_soc_data *soc_data;
 	struct clk *hclock;
 	struct clk *gck;
 	struct clk *mainck;
@@ -141,12 +148,24 @@ static const struct sdhci_ops sdhci_at91_sama5d2_ops = {
 	.set_power		= sdhci_at91_set_power,
 };
 
-static const struct sdhci_pltfm_data soc_data_sama5d2 = {
+static const struct sdhci_pltfm_data sdhci_sama5d2_pdata = {
 	.ops = &sdhci_at91_sama5d2_ops,
 };
 
+static const struct sdhci_at91_soc_data soc_data_sama5d2 = {
+	.pdata = &sdhci_sama5d2_pdata,
+	.baseclk_is_generated_internally = false,
+};
+
+static const struct sdhci_at91_soc_data soc_data_sam9x60 = {
+	.pdata = &sdhci_sama5d2_pdata,
+	.baseclk_is_generated_internally = true,
+	.divider_for_baseclk = 2,
+};
+
 static const struct of_device_id sdhci_at91_dt_match[] = {
 	{ .compatible = "atmel,sama5d2-sdhci", .data = &soc_data_sama5d2 },
+	{ .compatible = "microchip,sam9x60-sdhci", .data = &soc_data_sam9x60 },
 	{}
 };
 MODULE_DEVICE_TABLE(of, sdhci_at91_dt_match);
@@ -156,50 +175,37 @@ static int sdhci_at91_set_clks_presets(struct device *dev)
 	struct sdhci_host *host = dev_get_drvdata(dev);
 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 	struct sdhci_at91_priv *priv = sdhci_pltfm_priv(pltfm_host);
-	int ret;
 	unsigned int			caps0, caps1;
 	unsigned int			clk_base, clk_mul;
-	unsigned int			gck_rate, real_gck_rate;
+	unsigned int			gck_rate, clk_base_rate;
 	unsigned int			preset_div;
 
-	/*
-	 * The mult clock is provided by as a generated clock by the PMC
-	 * controller. In order to set the rate of gck, we have to get the
-	 * base clock rate and the clock mult from capabilities.
-	 */
 	clk_prepare_enable(priv->hclock);
 	caps0 = readl(host->ioaddr + SDHCI_CAPABILITIES);
 	caps1 = readl(host->ioaddr + SDHCI_CAPABILITIES_1);
-	clk_base = (caps0 & SDHCI_CLOCK_V3_BASE_MASK) >> SDHCI_CLOCK_BASE_SHIFT;
-	clk_mul = (caps1 & SDHCI_CLOCK_MUL_MASK) >> SDHCI_CLOCK_MUL_SHIFT;
-	gck_rate = clk_base * 1000000 * (clk_mul + 1);
-	ret = clk_set_rate(priv->gck, gck_rate);
-	if (ret < 0) {
-		dev_err(dev, "failed to set gck");
-		clk_disable_unprepare(priv->hclock);
-		return ret;
-	}
-	/*
-	 * We need to check if we have the requested rate for gck because in
-	 * some cases this rate could be not supported. If it happens, the rate
-	 * is the closest one gck can provide. We have to update the value
-	 * of clk mul.
-	 */
-	real_gck_rate = clk_get_rate(priv->gck);
-	if (real_gck_rate != gck_rate) {
-		clk_mul = real_gck_rate / (clk_base * 1000000) - 1;
-		caps1 &= (~SDHCI_CLOCK_MUL_MASK);
-		caps1 |= ((clk_mul << SDHCI_CLOCK_MUL_SHIFT) &
-			  SDHCI_CLOCK_MUL_MASK);
-		/* Set capabilities in r/w mode. */
-		writel(SDMMC_CACR_KEY | SDMMC_CACR_CAPWREN,
-		       host->ioaddr + SDMMC_CACR);
-		writel(caps1, host->ioaddr + SDHCI_CAPABILITIES_1);
-		/* Set capabilities in ro mode. */
-		writel(0, host->ioaddr + SDMMC_CACR);
-		dev_info(dev, "update clk mul to %u as gck rate is %u Hz\n",
-			 clk_mul, real_gck_rate);
-	}
+
+	gck_rate = clk_get_rate(priv->gck);
+	if (priv->soc_data->baseclk_is_generated_internally)
+		clk_base_rate = gck_rate / priv->soc_data->divider_for_baseclk;
+	else
+		clk_base_rate = clk_get_rate(priv->mainck);
+

drivers/mmc/host/sdhci-of-at91.c static int sdhci_at91_set_clks_presets(struct device *dev) · line 202

Quoted 10 lines
drivers/mmc/host/sdhci-of-at91.c +10 -0
+	clk_base = clk_base_rate / 1000000;
+	clk_mul = gck_rate / clk_base_rate - 1;
+
+	caps0 &= (~SDHCI_CLOCK_V3_BASE_MASK);
+	caps0 |= ((clk_base << SDHCI_CLOCK_BASE_SHIFT) & SDHCI_CLOCK_V3_BASE_MASK);
+	caps1 &= (~SDHCI_CLOCK_MUL_MASK);
+	caps1 |= ((clk_mul << SDHCI_CLOCK_MUL_SHIFT) & SDHCI_CLOCK_MUL_MASK);
+	/* Set capabilities in r/w mode. */
+	writel(SDMMC_CACR_KEY | SDMMC_CACR_CAPWREN, host->ioaddr + SDMMC_CACR);
+	writel(caps0, host->ioaddr + SDHCI_CAPABILITIES_1);

Shouldn't that be:

	writel(caps0, host->ioaddr + SDHCI_CAPABILITIES);
Quoted 70 lines
drivers/mmc/host/sdhci-of-at91.c +20 -9
+	writel(caps1, host->ioaddr + SDHCI_CAPABILITIES_1);
+	/* Set capabilities in ro mode. */
+	writel(0, host->ioaddr + SDMMC_CACR);
+
+	dev_info(dev, "update clk mul to %u as gck rate is %u Hz and clk base is %u Hz\n",
+		 clk_mul, gck_rate, clk_base_rate);
 
 	/*
 	 * We have to set preset values because it depends on the clk_mul
@@ -207,19 +213,19 @@ static int sdhci_at91_set_clks_presets(struct device *dev)
 	 * maximum sd clock value is 120 MHz instead of 208 MHz. For that
 	 * reason, we need to use presets to support SDR104.
 	 */
-	preset_div = DIV_ROUND_UP(real_gck_rate, 24000000) - 1;
+	preset_div = DIV_ROUND_UP(gck_rate, 24000000) - 1;
 	writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
 	       host->ioaddr + SDHCI_PRESET_FOR_SDR12);
-	preset_div = DIV_ROUND_UP(real_gck_rate, 50000000) - 1;
+	preset_div = DIV_ROUND_UP(gck_rate, 50000000) - 1;
 	writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
 	       host->ioaddr + SDHCI_PRESET_FOR_SDR25);
-	preset_div = DIV_ROUND_UP(real_gck_rate, 100000000) - 1;
+	preset_div = DIV_ROUND_UP(gck_rate, 100000000) - 1;
 	writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
 	       host->ioaddr + SDHCI_PRESET_FOR_SDR50);
-	preset_div = DIV_ROUND_UP(real_gck_rate, 120000000) - 1;
+	preset_div = DIV_ROUND_UP(gck_rate, 120000000) - 1;
 	writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
 	       host->ioaddr + SDHCI_PRESET_FOR_SDR104);
-	preset_div = DIV_ROUND_UP(real_gck_rate, 50000000) - 1;
+	preset_div = DIV_ROUND_UP(gck_rate, 50000000) - 1;
 	writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
 	       host->ioaddr + SDHCI_PRESET_FOR_DDR50);
 
@@ -314,7 +320,7 @@ static const struct dev_pm_ops sdhci_at91_dev_pm_ops = {
 static int sdhci_at91_probe(struct platform_device *pdev)
 {
 	const struct of_device_id	*match;
-	const struct sdhci_pltfm_data	*soc_data;
+	const struct sdhci_at91_soc_data	*soc_data;
 	struct sdhci_host		*host;
 	struct sdhci_pltfm_host		*pltfm_host;
 	struct sdhci_at91_priv		*priv;
@@ -325,17 +331,22 @@ static int sdhci_at91_probe(struct platform_device *pdev)
 		return -EINVAL;
 	soc_data = match->data;
 
-	host = sdhci_pltfm_init(pdev, soc_data, sizeof(*priv));
+	host = sdhci_pltfm_init(pdev, soc_data->pdata, sizeof(*priv));
 	if (IS_ERR(host))
 		return PTR_ERR(host);
 
 	pltfm_host = sdhci_priv(host);
 	priv = sdhci_pltfm_priv(pltfm_host);
+	priv->soc_data = soc_data;
 
 	priv->mainck = devm_clk_get(&pdev->dev, "baseclk");
 	if (IS_ERR(priv->mainck)) {
-		dev_err(&pdev->dev, "failed to get baseclk\n");
-		return PTR_ERR(priv->mainck);
+		if (soc_data->baseclk_is_generated_internally) {
+			priv->mainck = NULL;
+		} else {
+			dev_err(&pdev->dev, "failed to get baseclk\n");
+			return PTR_ERR(priv->mainck);
+		}
 	}
 
 	priv->hclock = devm_clk_get(&pdev->dev, "hclock");
#3 lore raw

PATCH v4 2/3 mmc: sdhci-of-at91: rework clocks management to support SAM9x60 device

In the SAM9x60 SoC, there are only two clocks instead of three for the SDHCI device. The base clk is no longer provided, it is generated internally from the mult clk.

The values of the base clk and mul in the capabilities registers may not reflect the reality as the mult clk is a programmable clock which can take several rates. As we can't trust those values, take them from the clock tree and update the capabilities according to.

As we can have the same pitfall, in some cases, with the SAMA5D2 Soc, stop relying on capabilities too.

---

Thanks Adrian for pointing out the typo. It's fixed and re-tested.

Let me know if you want to me to resend the full serie or if it's ok.

Regards

Ludovic

 drivers/mmc/host/sdhci-of-at91.c | 105 +++++++++++++++++--------------
 1 file changed, 58 insertions(+), 47 deletions(-)
drivers/mmc/host/sdhci-of-at91.c +58 -47
index 5959e394b416..b95ac4b27f22 100644
@@ -33,7 +33,14 @@
 
 #define SDHCI_AT91_PRESET_COMMON_CONF	0x400 /* drv type B, programmable clock mode */
 
+struct sdhci_at91_soc_data {
+	const struct sdhci_pltfm_data *pdata;
+	bool baseclk_is_generated_internally;
+	unsigned int divider_for_baseclk;
+};
+
 struct sdhci_at91_priv {
+	const struct sdhci_at91_soc_data *soc_data;
 	struct clk *hclock;
 	struct clk *gck;
 	struct clk *mainck;
@@ -141,12 +148,24 @@ static const struct sdhci_ops sdhci_at91_sama5d2_ops = {
 	.set_power		= sdhci_at91_set_power,
 };
 
-static const struct sdhci_pltfm_data soc_data_sama5d2 = {
+static const struct sdhci_pltfm_data sdhci_sama5d2_pdata = {
 	.ops = &sdhci_at91_sama5d2_ops,
 };
 
+static const struct sdhci_at91_soc_data soc_data_sama5d2 = {
+	.pdata = &sdhci_sama5d2_pdata,
+	.baseclk_is_generated_internally = false,
+};
+
+static const struct sdhci_at91_soc_data soc_data_sam9x60 = {
+	.pdata = &sdhci_sama5d2_pdata,
+	.baseclk_is_generated_internally = true,
+	.divider_for_baseclk = 2,
+};
+
 static const struct of_device_id sdhci_at91_dt_match[] = {
 	{ .compatible = "atmel,sama5d2-sdhci", .data = &soc_data_sama5d2 },
+	{ .compatible = "microchip,sam9x60-sdhci", .data = &soc_data_sam9x60 },
 	{}
 };
 MODULE_DEVICE_TABLE(of, sdhci_at91_dt_match);
@@ -156,50 +175,37 @@ static int sdhci_at91_set_clks_presets(struct device *dev)
 	struct sdhci_host *host = dev_get_drvdata(dev);
 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 	struct sdhci_at91_priv *priv = sdhci_pltfm_priv(pltfm_host);
-	int ret;
 	unsigned int			caps0, caps1;
 	unsigned int			clk_base, clk_mul;
-	unsigned int			gck_rate, real_gck_rate;
+	unsigned int			gck_rate, clk_base_rate;
 	unsigned int			preset_div;
 
-	/*
-	 * The mult clock is provided by as a generated clock by the PMC
-	 * controller. In order to set the rate of gck, we have to get the
-	 * base clock rate and the clock mult from capabilities.
-	 */
 	clk_prepare_enable(priv->hclock);
 	caps0 = readl(host->ioaddr + SDHCI_CAPABILITIES);
 	caps1 = readl(host->ioaddr + SDHCI_CAPABILITIES_1);
-	clk_base = (caps0 & SDHCI_CLOCK_V3_BASE_MASK) >> SDHCI_CLOCK_BASE_SHIFT;
-	clk_mul = (caps1 & SDHCI_CLOCK_MUL_MASK) >> SDHCI_CLOCK_MUL_SHIFT;
-	gck_rate = clk_base * 1000000 * (clk_mul + 1);
-	ret = clk_set_rate(priv->gck, gck_rate);
-	if (ret < 0) {
-		dev_err(dev, "failed to set gck");
-		clk_disable_unprepare(priv->hclock);
-		return ret;
-	}
-	/*
-	 * We need to check if we have the requested rate for gck because in
-	 * some cases this rate could be not supported. If it happens, the rate
-	 * is the closest one gck can provide. We have to update the value
-	 * of clk mul.
-	 */
-	real_gck_rate = clk_get_rate(priv->gck);
-	if (real_gck_rate != gck_rate) {
-		clk_mul = real_gck_rate / (clk_base * 1000000) - 1;
-		caps1 &= (~SDHCI_CLOCK_MUL_MASK);
-		caps1 |= ((clk_mul << SDHCI_CLOCK_MUL_SHIFT) &
-			  SDHCI_CLOCK_MUL_MASK);
-		/* Set capabilities in r/w mode. */
-		writel(SDMMC_CACR_KEY | SDMMC_CACR_CAPWREN,
-		       host->ioaddr + SDMMC_CACR);
-		writel(caps1, host->ioaddr + SDHCI_CAPABILITIES_1);
-		/* Set capabilities in ro mode. */
-		writel(0, host->ioaddr + SDMMC_CACR);
-		dev_info(dev, "update clk mul to %u as gck rate is %u Hz\n",
-			 clk_mul, real_gck_rate);
-	}
+
+	gck_rate = clk_get_rate(priv->gck);
+	if (priv->soc_data->baseclk_is_generated_internally)
+		clk_base_rate = gck_rate / priv->soc_data->divider_for_baseclk;
+	else
+		clk_base_rate = clk_get_rate(priv->mainck);
+
+	clk_base = clk_base_rate / 1000000;
+	clk_mul = gck_rate / clk_base_rate - 1;
+
+	caps0 &= (~SDHCI_CLOCK_V3_BASE_MASK);
+	caps0 |= ((clk_base << SDHCI_CLOCK_BASE_SHIFT) & SDHCI_CLOCK_V3_BASE_MASK);
+	caps1 &= (~SDHCI_CLOCK_MUL_MASK);
+	caps1 |= ((clk_mul << SDHCI_CLOCK_MUL_SHIFT) & SDHCI_CLOCK_MUL_MASK);
+	/* Set capabilities in r/w mode. */
+	writel(SDMMC_CACR_KEY | SDMMC_CACR_CAPWREN, host->ioaddr + SDMMC_CACR);
+	writel(caps0, host->ioaddr + SDHCI_CAPABILITIES);
+	writel(caps1, host->ioaddr + SDHCI_CAPABILITIES_1);
+	/* Set capabilities in ro mode. */
+	writel(0, host->ioaddr + SDMMC_CACR);
+
+	dev_info(dev, "update clk mul to %u as gck rate is %u Hz and clk base is %u Hz\n",
+		 clk_mul, gck_rate, clk_base_rate);
 
 	/*
 	 * We have to set preset values because it depends on the clk_mul
@@ -207,19 +213,19 @@ static int sdhci_at91_set_clks_presets(struct device *dev)
 	 * maximum sd clock value is 120 MHz instead of 208 MHz. For that
 	 * reason, we need to use presets to support SDR104.
 	 */
-	preset_div = DIV_ROUND_UP(real_gck_rate, 24000000) - 1;
+	preset_div = DIV_ROUND_UP(gck_rate, 24000000) - 1;
 	writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
 	       host->ioaddr + SDHCI_PRESET_FOR_SDR12);
-	preset_div = DIV_ROUND_UP(real_gck_rate, 50000000) - 1;
+	preset_div = DIV_ROUND_UP(gck_rate, 50000000) - 1;
 	writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
 	       host->ioaddr + SDHCI_PRESET_FOR_SDR25);
-	preset_div = DIV_ROUND_UP(real_gck_rate, 100000000) - 1;
+	preset_div = DIV_ROUND_UP(gck_rate, 100000000) - 1;
 	writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
 	       host->ioaddr + SDHCI_PRESET_FOR_SDR50);
-	preset_div = DIV_ROUND_UP(real_gck_rate, 120000000) - 1;
+	preset_div = DIV_ROUND_UP(gck_rate, 120000000) - 1;
 	writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
 	       host->ioaddr + SDHCI_PRESET_FOR_SDR104);
-	preset_div = DIV_ROUND_UP(real_gck_rate, 50000000) - 1;
+	preset_div = DIV_ROUND_UP(gck_rate, 50000000) - 1;
 	writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
 	       host->ioaddr + SDHCI_PRESET_FOR_DDR50);
 
@@ -314,7 +320,7 @@ static const struct dev_pm_ops sdhci_at91_dev_pm_ops = {
 static int sdhci_at91_probe(struct platform_device *pdev)
 {
 	const struct of_device_id	*match;
-	const struct sdhci_pltfm_data	*soc_data;
+	const struct sdhci_at91_soc_data	*soc_data;
 	struct sdhci_host		*host;
 	struct sdhci_pltfm_host		*pltfm_host;
 	struct sdhci_at91_priv		*priv;
@@ -325,17 +331,22 @@ static int sdhci_at91_probe(struct platform_device *pdev)
 		return -EINVAL;
 	soc_data = match->data;
 
-	host = sdhci_pltfm_init(pdev, soc_data, sizeof(*priv));
+	host = sdhci_pltfm_init(pdev, soc_data->pdata, sizeof(*priv));
 	if (IS_ERR(host))
 		return PTR_ERR(host);
 
 	pltfm_host = sdhci_priv(host);
 	priv = sdhci_pltfm_priv(pltfm_host);
+	priv->soc_data = soc_data;
 
 	priv->mainck = devm_clk_get(&pdev->dev, "baseclk");
 	if (IS_ERR(priv->mainck)) {
-		dev_err(&pdev->dev, "failed to get baseclk\n");
-		return PTR_ERR(priv->mainck);
+		if (soc_data->baseclk_is_generated_internally) {
+			priv->mainck = NULL;
+		} else {
+			dev_err(&pdev->dev, "failed to get baseclk\n");
+			return PTR_ERR(priv->mainck);
+		}
 	}
 
 	priv->hclock = devm_clk_get(&pdev->dev, "hclock");
Signature · 1 line
2.24.0
maintainer Acked-by on v4 2/3
#4 lore raw

Re: [PATCH v4 2/3] mmc: sdhci-of-at91: rework clocks management to support SAM9x60 device

Quoted 12 lines · Ludovic Desroches

In the SAM9x60 SoC, there are only two clocks instead of three for the SDHCI device. The base clk is no longer provided, it is generated internally from the mult clk.

The values of the base clk and mul in the capabilities registers may not reflect the reality as the mult clk is a programmable clock which can take several rates. As we can't trust those values, take them from the clock tree and update the capabilities according to.

As we can have the same pitfall, in some cases, with the SAMA5D2 Soc, stop relying on capabilities too.

Quoted 6 lines

---

Thanks Adrian for pointing out the typo. It's fixed and re-tested.

Let me know if you want to me to resend the full serie or if it's ok.

This is fine for me, although one more very minor comment below. If you fix that you can add my ack:

Quoted 106 lines

Regards

Ludovic

 drivers/mmc/host/sdhci-of-at91.c | 105 +++++++++++++++++--------------
 1 file changed, 58 insertions(+), 47 deletions(-)
drivers/mmc/host/sdhci-of-at91.c +25 -38
index 5959e394b416..b95ac4b27f22 100644
@@ -33,7 +33,14 @@
 
 #define SDHCI_AT91_PRESET_COMMON_CONF	0x400 /* drv type B, programmable clock mode */
 
+struct sdhci_at91_soc_data {
+	const struct sdhci_pltfm_data *pdata;
+	bool baseclk_is_generated_internally;
+	unsigned int divider_for_baseclk;
+};
+
 struct sdhci_at91_priv {
+	const struct sdhci_at91_soc_data *soc_data;
 	struct clk *hclock;
 	struct clk *gck;
 	struct clk *mainck;
@@ -141,12 +148,24 @@ static const struct sdhci_ops sdhci_at91_sama5d2_ops = {
 	.set_power		= sdhci_at91_set_power,
 };
 
-static const struct sdhci_pltfm_data soc_data_sama5d2 = {
+static const struct sdhci_pltfm_data sdhci_sama5d2_pdata = {
 	.ops = &sdhci_at91_sama5d2_ops,
 };
 
+static const struct sdhci_at91_soc_data soc_data_sama5d2 = {
+	.pdata = &sdhci_sama5d2_pdata,
+	.baseclk_is_generated_internally = false,
+};
+
+static const struct sdhci_at91_soc_data soc_data_sam9x60 = {
+	.pdata = &sdhci_sama5d2_pdata,
+	.baseclk_is_generated_internally = true,
+	.divider_for_baseclk = 2,
+};
+
 static const struct of_device_id sdhci_at91_dt_match[] = {
 	{ .compatible = "atmel,sama5d2-sdhci", .data = &soc_data_sama5d2 },
+	{ .compatible = "microchip,sam9x60-sdhci", .data = &soc_data_sam9x60 },
 	{}
 };
 MODULE_DEVICE_TABLE(of, sdhci_at91_dt_match);
@@ -156,50 +175,37 @@ static int sdhci_at91_set_clks_presets(struct device *dev)
 	struct sdhci_host *host = dev_get_drvdata(dev);
 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 	struct sdhci_at91_priv *priv = sdhci_pltfm_priv(pltfm_host);
-	int ret;
 	unsigned int			caps0, caps1;
 	unsigned int			clk_base, clk_mul;
-	unsigned int			gck_rate, real_gck_rate;
+	unsigned int			gck_rate, clk_base_rate;
 	unsigned int			preset_div;
 
-	/*
-	 * The mult clock is provided by as a generated clock by the PMC
-	 * controller. In order to set the rate of gck, we have to get the
-	 * base clock rate and the clock mult from capabilities.
-	 */
 	clk_prepare_enable(priv->hclock);
 	caps0 = readl(host->ioaddr + SDHCI_CAPABILITIES);
 	caps1 = readl(host->ioaddr + SDHCI_CAPABILITIES_1);
-	clk_base = (caps0 & SDHCI_CLOCK_V3_BASE_MASK) >> SDHCI_CLOCK_BASE_SHIFT;
-	clk_mul = (caps1 & SDHCI_CLOCK_MUL_MASK) >> SDHCI_CLOCK_MUL_SHIFT;
-	gck_rate = clk_base * 1000000 * (clk_mul + 1);
-	ret = clk_set_rate(priv->gck, gck_rate);
-	if (ret < 0) {
-		dev_err(dev, "failed to set gck");
-		clk_disable_unprepare(priv->hclock);
-		return ret;
-	}
-	/*
-	 * We need to check if we have the requested rate for gck because in
-	 * some cases this rate could be not supported. If it happens, the rate
-	 * is the closest one gck can provide. We have to update the value
-	 * of clk mul.
-	 */
-	real_gck_rate = clk_get_rate(priv->gck);
-	if (real_gck_rate != gck_rate) {
-		clk_mul = real_gck_rate / (clk_base * 1000000) - 1;
-		caps1 &= (~SDHCI_CLOCK_MUL_MASK);
-		caps1 |= ((clk_mul << SDHCI_CLOCK_MUL_SHIFT) &
-			  SDHCI_CLOCK_MUL_MASK);
-		/* Set capabilities in r/w mode. */
-		writel(SDMMC_CACR_KEY | SDMMC_CACR_CAPWREN,
-		       host->ioaddr + SDMMC_CACR);
-		writel(caps1, host->ioaddr + SDHCI_CAPABILITIES_1);
-		/* Set capabilities in ro mode. */
-		writel(0, host->ioaddr + SDMMC_CACR);
-		dev_info(dev, "update clk mul to %u as gck rate is %u Hz\n",
-			 clk_mul, real_gck_rate);
-	}
+
+	gck_rate = clk_get_rate(priv->gck);
+	if (priv->soc_data->baseclk_is_generated_internally)
+		clk_base_rate = gck_rate / priv->soc_data->divider_for_baseclk;

drivers/mmc/host/sdhci-of-at91.c static int sdhci_at91_set_clks_presets(struct device *dev) · line 199

Quoted 10 lines
drivers/mmc/host/sdhci-of-at91.c +10 -0
+	else
+		clk_base_rate = clk_get_rate(priv->mainck);
+
+	clk_base = clk_base_rate / 1000000;
+	clk_mul = gck_rate / clk_base_rate - 1;
+
+	caps0 &= (~SDHCI_CLOCK_V3_BASE_MASK);
+	caps0 |= ((clk_base << SDHCI_CLOCK_BASE_SHIFT) & SDHCI_CLOCK_V3_BASE_MASK);
+	caps1 &= (~SDHCI_CLOCK_MUL_MASK);
+	caps1 |= ((clk_mul << SDHCI_CLOCK_MUL_SHIFT) & SDHCI_CLOCK_MUL_MASK);

The 4 assignments above do not need extra parentheses i.e.

	caps0 &= ~SDHCI_CLOCK_V3_BASE_MASK;
	caps0 |= (clk_base << SDHCI_CLOCK_BASE_SHIFT) & SDHCI_CLOCK_V3_BASE_MASK;
	caps1 &= ~SDHCI_CLOCK_MUL_MASK;
	caps1 |= (clk_mul << SDHCI_CLOCK_MUL_SHIFT) & SDHCI_CLOCK_MUL_MASK;
Quoted 73 lines
drivers/mmc/host/sdhci-of-at91.c +23 -9
+	/* Set capabilities in r/w mode. */
+	writel(SDMMC_CACR_KEY | SDMMC_CACR_CAPWREN, host->ioaddr + SDMMC_CACR);
+	writel(caps0, host->ioaddr + SDHCI_CAPABILITIES);
+	writel(caps1, host->ioaddr + SDHCI_CAPABILITIES_1);
+	/* Set capabilities in ro mode. */
+	writel(0, host->ioaddr + SDMMC_CACR);
+
+	dev_info(dev, "update clk mul to %u as gck rate is %u Hz and clk base is %u Hz\n",
+		 clk_mul, gck_rate, clk_base_rate);
 
 	/*
 	 * We have to set preset values because it depends on the clk_mul
@@ -207,19 +213,19 @@ static int sdhci_at91_set_clks_presets(struct device *dev)
 	 * maximum sd clock value is 120 MHz instead of 208 MHz. For that
 	 * reason, we need to use presets to support SDR104.
 	 */
-	preset_div = DIV_ROUND_UP(real_gck_rate, 24000000) - 1;
+	preset_div = DIV_ROUND_UP(gck_rate, 24000000) - 1;
 	writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
 	       host->ioaddr + SDHCI_PRESET_FOR_SDR12);
-	preset_div = DIV_ROUND_UP(real_gck_rate, 50000000) - 1;
+	preset_div = DIV_ROUND_UP(gck_rate, 50000000) - 1;
 	writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
 	       host->ioaddr + SDHCI_PRESET_FOR_SDR25);
-	preset_div = DIV_ROUND_UP(real_gck_rate, 100000000) - 1;
+	preset_div = DIV_ROUND_UP(gck_rate, 100000000) - 1;
 	writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
 	       host->ioaddr + SDHCI_PRESET_FOR_SDR50);
-	preset_div = DIV_ROUND_UP(real_gck_rate, 120000000) - 1;
+	preset_div = DIV_ROUND_UP(gck_rate, 120000000) - 1;
 	writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
 	       host->ioaddr + SDHCI_PRESET_FOR_SDR104);
-	preset_div = DIV_ROUND_UP(real_gck_rate, 50000000) - 1;
+	preset_div = DIV_ROUND_UP(gck_rate, 50000000) - 1;
 	writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
 	       host->ioaddr + SDHCI_PRESET_FOR_DDR50);
 
@@ -314,7 +320,7 @@ static const struct dev_pm_ops sdhci_at91_dev_pm_ops = {
 static int sdhci_at91_probe(struct platform_device *pdev)
 {
 	const struct of_device_id	*match;
-	const struct sdhci_pltfm_data	*soc_data;
+	const struct sdhci_at91_soc_data	*soc_data;
 	struct sdhci_host		*host;
 	struct sdhci_pltfm_host		*pltfm_host;
 	struct sdhci_at91_priv		*priv;
@@ -325,17 +331,22 @@ static int sdhci_at91_probe(struct platform_device *pdev)
 		return -EINVAL;
 	soc_data = match->data;
 
-	host = sdhci_pltfm_init(pdev, soc_data, sizeof(*priv));
+	host = sdhci_pltfm_init(pdev, soc_data->pdata, sizeof(*priv));
 	if (IS_ERR(host))
 		return PTR_ERR(host);
 
 	pltfm_host = sdhci_priv(host);
 	priv = sdhci_pltfm_priv(pltfm_host);
+	priv->soc_data = soc_data;
 
 	priv->mainck = devm_clk_get(&pdev->dev, "baseclk");
 	if (IS_ERR(priv->mainck)) {
-		dev_err(&pdev->dev, "failed to get baseclk\n");
-		return PTR_ERR(priv->mainck);
+		if (soc_data->baseclk_is_generated_internally) {
+			priv->mainck = NULL;
+		} else {
+			dev_err(&pdev->dev, "failed to get baseclk\n");
+			return PTR_ERR(priv->mainck);
+		}
 	}
 
 	priv->hclock = devm_clk_get(&pdev->dev, "hclock");
#5 lore raw

PATCH v3 3/3 ARM: dts: at91: sama5d2: set the sdmmc gclk frequency

In reply to Ludovic Desroches

Set the frequency of the generated clock used by sdmmc devices in order to not rely on the configuration done by previous components.

---

Changes:
- v3: none
- v2: none

 arch/arm/boot/dts/sama5d2.dtsi | 4 ++++
 1 file changed, 4 insertions(+)
arch/arm/boot/dts/sama5d2.dtsi +4 -0
index fa3b9c30a63a..f013c3562724 100644
@@ -300,6 +300,8 @@ sdmmc0: sdio-host@a0000000 {
 			interrupts = <31 IRQ_TYPE_LEVEL_HIGH 0>;
 			clocks = <&pmc PMC_TYPE_PERIPHERAL 31>, <&pmc PMC_TYPE_GCK 31>, <&pmc PMC_TYPE_CORE PMC_MAIN>;
 			clock-names = "hclock", "multclk", "baseclk";
+			assigned-clocks = <&pmc PMC_TYPE_GCK 31>;
+			assigned-clock-rates = <480000000>;
 			status = "disabled";
 		};
 
@@ -309,6 +311,8 @@ sdmmc1: sdio-host@b0000000 {
 			interrupts = <32 IRQ_TYPE_LEVEL_HIGH 0>;
 			clocks = <&pmc PMC_TYPE_PERIPHERAL 32>, <&pmc PMC_TYPE_GCK 32>, <&pmc PMC_TYPE_CORE PMC_MAIN>;
 			clock-names = "hclock", "multclk", "baseclk";
+			assigned-clocks = <&pmc PMC_TYPE_GCK 32>;
+			assigned-clock-rates = <480000000>;
 			status = "disabled";
 		};
 
Signature · 1 line
2.24.0.rc0