Skip to contentSkip to conversation

SNES gamepad doesn't work with kernel 2.6.x

DISCUSSION Alexander Fieroch 2 participants 7 messages Nov 11, 2004 – Nov 18, 2004

lore
Share & tools
lore
#0 lore raw

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Hello,

I'm using a SNES gamepad at my parallel port. With kernel 2.4.x it works, but with kernel 2.6.x I get following error while inserting the module:

# modprobe gamecon gc=0,1,0,0,0,0
FATAL: Error inserting gamecon
(/lib/modules/2.6.9/kernel/drivers/input/joystick/gamecon.ko): No such
device
# modprobe gamecon gamecon.map=0,1,0,0,0,0
FATAL: Error inserting gamecon
(/lib/modules/2.6.9/kernel/drivers/input/joystick/gamecon.ko): No such
device

The module lp is not loaded while parport is. With kernel 2.4.x there are no problems - so is it a bug?

Thanks in advance,
Alexander
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.2.5 (GNU/Linux)

iD8DBQFBk5PLlLqZutoTiOMRAu+IAJ9wzegM5+BB7prIRZi626qqHAsVnQCeK/G/ 7LhnIybXM/ogsY5AqC3kMQc=
=BiN9
-----END PGP SIGNATURE-----

#1 lore raw

Hi,

Quoted 1 line

With kernel 2.4.x there are no problems - so is it a bug?

it works for me without problems. are you sure that you loaded parport_pc as well?

--
Aristeu

#2 lore raw

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Aristeu Sergio Rozanski Filho wrote:
| it works for me without problems. are you sure that you loaded | parport_pc as well?

Yes, the modules parport and parport_pc are loaded. So what else is important and could cause this conflict?

Thanks in advance,
Alexander Fieroch
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.2.5 (GNU/Linux)

iD8DBQFBk+s8lLqZutoTiOMRAgw3AJ4rvshTCJEt0/02CISC6GkRwoo7cgCfX+9F 5hrNg/yKv/+0J5PNgxOUubw=
=qZ1a
-----END PGP SIGNATURE-----

#3 lore raw

Hi!

Quoted 2 lines

Yes, the modules parport and parport_pc are loaded. So what else is important and could cause this conflict?

could you send the output of 'dmesg' command? it may give a hint of what's going on.
thanks,

Signature · 1 line
Aristeu
#4 lore raw

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Aristeu Sergio Rozanski Filho wrote:
| could you send the output of 'dmesg' command? it may give a hint of | what's going on.

hm, when I try to start the module with

# modprobe gamecon gamecon.map=0,1,0,0,0,0

or

# modprobe gamecon gc=0,1,0,0,0,0

I get "gamecon: Unknown parameter `gamecon.map'" in /var/log/syslog and dmesg.
Just trying to load it with

# modprobe gamecon

returns the error again and no message in /var/log/syslog or dmesg.

# modprobe gamecon
FATAL: Error inserting gamecon
(/lib/modules/2.6.9/kernel/drivers/input/joystick/gamecon.ko): No such
device

So there are no further hints... :-/
How do you load the module? just with "modprobe gamecon" or any parameters?

Greetings,
Alexander

-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.2.5 (GNU/Linux)

iD8DBQFBlP+WlLqZutoTiOMRAi0/AKCL0LfSeWZRZcSD58oUbwgP6IhYxgCfUAdz /oYUH19Oyd9RVKTEhm/lzhg=
=kf+m
-----END PGP SIGNATURE-----

#5 lore raw

Hi!

Quoted 8 lines
# modprobe gamecon gamecon.map=0,1,0,0,0,0

or

# modprobe gamecon gc=0,1,0,0,0,0

I get "gamecon: Unknown parameter `gamecon.map'" in /var/log/syslog and dmesg.

maybe I'm wrong but the format foo.bar= is only used when it's compiled as built-in, not as module

then, try do:
modprobe gamecon map=0,1

it should work

Signature · 1 line
Aristeu
#6 lore raw

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Aristeu Sergio Rozanski Filho wrote:

| maybe I'm wrong but the format foo.bar= is only used when it's
| compiled as built-in, not as module
|
| then, try do:
|    modprobe gamecon map=0,1
|
| it should work

Yes thanks, it works! Now I can load the module gamecon but the gamepad does not respond for example with jstest or jscalibrator.
So doesn't my parallel port supply the gameport with enough power?

Thanks,
Alexander
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.2.5 (GNU/Linux)

iD8DBQFBnTBtlLqZutoTiOMRAsQfAJ9QI5ZAZHQ0VvQrsNfCHbe1UjuXSACdFfHG akhsG0A630nNovd0Al/TY/w=
=JjMp
-----END PGP SIGNATURE-----