rk3288 (Tinkerboard) not booting
Anyone know a way to get a functional u-boot on the rk3288? (Tinkerboard, SD)
The docs seem to recommend:
$ /tmp/arm-build/tools/mkimage -n rk3288 -T rksd -d arm/tinkerboard/u-boot-spl-dtb.bin out
However, that produces:
Warning: SPL image is too large (size 0xb000) and will not boot
I saw this patch to disable I2C in the SPL to reduce its size:
https://github.com/xypron/u-boot-patches/blob/df2ceb65fb4cc433aa17304ed9d3d591c14ef5ac/0001-configs-tinker-rk3288-disable-CONFIG_SPL_I2C_SUPPORT.patch
However, that breaks the build :-|
LD spl/u-boot-spl
arm-unknown-haiku-ld.bfd: drivers/built-in.o: in function `rk8xx_write':/tmp/arm-build/drivers/power/pmic/rk8xx.c:30: undefined reference to dm_i2c_write' arm-unknown-haiku-ld.bfd: drivers/built-in.o: in function rk8xx_read':/tmp/arm-build/drivers/power/pmic/rk8xx.c:43: undefined reference to `dm_i2c_read' make[1]: *** [scripts/Makefile.spl:404: spl/u-boot-spl] Error 1
make: *** [Makefile:1762: spl/u-boot-spl] Error 2
make: Leaving directory '/tmp/arm-build'
Disabling SPL Power then results in an error compiling MMC support
Any alternative methods to getting u-boot running from SD?
Rockchip devices seem to be kind of complex to get going :-|
-- Alex
Hi
Please use the latest uboot. The fixes should be already merged
Mcihael
Quoted 30 lines · Alexander von Gluck IV
Anyone know a way to get a functional u-boot on the rk3288? (Tinkerboard, SD)
The docs seem to recommend:
$ /tmp/arm-build/tools/mkimage -n rk3288 -T rksd -d arm/tinkerboard/u-boot-spl-dtb.bin outHowever, that produces:
Warning: SPL image is too large (size0xb000) and will not bootI saw this patch to disable I2C in the SPL to reduce its size:
https://github.com/xypron/u-boot-patches/blob/df2ceb65fb4cc433aa17304ed9d3d591c14ef5ac/0001-configs-tinker-rk3288-disable-CONFIG_SPL_I2C_SUPPORT.patchHowever, that breaks the build :-|
LD spl/u-boot-spl
arm-unknown-haiku-ld.bfd:drivers/built-in.o: in function `rk8xx_write':/tmp/arm-build/drivers/power/pmic/rk8xx.c:30: undefined reference todm_i2c_write' arm-unknown-haiku-ld.bfd: drivers/built-in.o: in functionrk8xx_read':/tmp/arm-build/drivers/power/pmic/rk8xx.c:43: undefined reference to `dm_i2c_read' make[1]: *** [scripts/Makefile.spl:404: spl/u-boot-spl] Error 1
make: *** [Makefile:1762: spl/u-boot-spl] Error 2
make: Leaving directory '/tmp/arm-build'
Disabling SPL Power then results in an error compiling MMC support
Any alternative methods to getting u-boot running from SD?
Rockchip devices seem to be kind of complex to get going :-|
-- Alex
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot
Signature · 4 lines
| Michael Nazzareno Trimarchi Amarula Solutions BV | | COO - Founder Cruquiuskade 47 | | +31(0)851119172 Amsterdam 1018 AM NL | | [`as] http://www.amarulasolutions.com |
Using master from git://git.denx.de/u-boot.git
commit 390183b58179ddaf986422f4d9446c596660f7e0 (HEAD -> master, origin/master, origin/HEAD)
Merge: d6c7309f56 79907a4f84
Author: Tom Rini <[email protected]>
Date: Sat Sep 21 07:31:23 2019 -0400
Merge tag 'efi-2019-10-rc4-5' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for v2019.10-rc4 (5)
This patch set fixes errors in the UEFI sub-system and adds a function to compare u16 strings which is prerequisite for further patches.
Same error:
$ ./tools/mkimage -n rk3288 -T rksd -d spl/u-boot-spl-dtb.bin out Warning: SPL image is too large (size 0xb000) and will not boot Error: image verification failed
$ ls -lah spl/u-boot-spl-dtb.bin -rw-rw-r-- 1 kallisti5 kallisti5 43K Sep 22 16:17 spl/u-boot-spl-dtb.bin
Quoted 45 lines · Michael Nazzareno Trimarchi
Hi
Please use the latest uboot. The fixes should be already merged
Mcihael
Quoted 14 lines · Alexander von Gluck IV
Anyone know a way to get a functional u-boot on the rk3288? (Tinkerboard, SD)
The docs seem to recommend:
$ /tmp/arm-build/tools/mkimage -n rk3288 -T rksd -d arm/tinkerboard/u-boot-spl-dtb.bin outHowever, that produces:
Warning: SPL image is too large (size0xb000) and will not bootI saw this patch to disable I2C in the SPL to reduce its size:
https://github.com/xypron/u-boot-patches/blob/df2ceb65fb4cc433aa17304ed9d3d591c14ef5ac/0001-configs-
inker-rk3288-disable-CONFIG_SPL_I2C_SUPPORT.patchHowever, that breaks the build :-|
Quoted 16 lines
LD spl/u-boot-spl
arm-unknown-haiku-ld.bfd:drivers/built-in.o: in function `rk8xx_write':/tmp/arm-build/drivers/power/pmic/rk8xx.c:30: undefined reference todm_i2c_write' arm-unknown-haiku-ld.bfd: drivers/built-in.o: in functionrk8xx_read':/tmp/arm-build/drivers/power/pmic/rk8xx.c:43: undefined reference to `dm_i2c_read' make[1]: *** [scripts/Makefile.spl:404: spl/u-boot-spl] Error 1
make: *** [Makefile:1762: spl/u-boot-spl] Error 2
make: Leaving directory '/tmp/arm-build'
Disabling SPL Power then results in an error compiling MMC support
Any alternative methods to getting u-boot running from SD?
Rockchip devices seem to be kind of complex to get going :-|
-- Alex
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot--
| Michael Nazzareno Trimarchi Amarula Solutions BV | | COO - Founder Cruquiuskade 47 | | +31(0)851119172 Amsterdam 1018 AM NL | | [`as] http://www.amarulasolutions.com |
Hi
https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip/commits/master
make idbloader.img
Michael
Quoted 76 lines · Alexander von Gluck IV
Using master from
git://git.denx.de/u-boot.gitcommit
390183b58179ddaf986422f4d9446c596660f7e0(HEAD -> master, origin/master, origin/HEAD)
Merge:d6c7309f5679907a4f84
Author: Tom Rini <[email protected]>
Date: Sat Sep 21 07:31:23 2019 -0400Merge tag 'efi-2019-10-rc4-5' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for v2019.10-rc4 (5)
This patch set fixes errors in the UEFI sub-system and adds a function to compare u16 strings which is prerequisite for further patches.
Same error:
$ ./tools/mkimage -n rk3288 -T rksd -d spl/u-boot-spl-dtb.bin out Warning: SPL image is too large (size 0xb000) and will not boot Error: image verification failed$ ls -lah spl/u-boot-spl-dtb.bin -rw-rw-r-- 1 kallisti5 kallisti5 43K Sep 22 16:17 spl/u-boot-spl-dtb.binQuoted 45 lines · Michael Nazzareno Trimarchi
Hi
Please use the latest uboot. The fixes should be already merged
Mcihael
Quoted 14 lines · Alexander von Gluck IV
Anyone know a way to get a functional u-boot on the rk3288? (Tinkerboard, SD)
The docs seem to recommend:
$ /tmp/arm-build/tools/mkimage -n rk3288 -T rksd -d arm/tinkerboard/u-boot-spl-dtb.bin outHowever, that produces:
Warning: SPL image is too large (size0xb000) and will not bootI saw this patch to disable I2C in the SPL to reduce its size:
https://github.com/xypron/u-boot-patches/blob/df2ceb65fb4cc433aa17304ed9d3d591c14ef5ac/0001-configs-
inker-rk3288-disable-CONFIG_SPL_I2C_SUPPORT.patchHowever, that breaks the build :-|
Quoted 16 lines
LD spl/u-boot-spl
arm-unknown-haiku-ld.bfd:drivers/built-in.o: in function `rk8xx_write':/tmp/arm-build/drivers/power/pmic/rk8xx.c:30: undefined reference todm_i2c_write' arm-unknown-haiku-ld.bfd: drivers/built-in.o: in functionrk8xx_read':/tmp/arm-build/drivers/power/pmic/rk8xx.c:43: undefined reference to `dm_i2c_read' make[1]: *** [scripts/Makefile.spl:404: spl/u-boot-spl] Error 1
make: *** [Makefile:1762: spl/u-boot-spl] Error 2
make: Leaving directory '/tmp/arm-build'
Disabling SPL Power then results in an error compiling MMC support
Any alternative methods to getting u-boot running from SD?
Rockchip devices seem to be kind of complex to get going :-|
-- Alex
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot--
| Michael Nazzareno Trimarchi Amarula Solutions BV | | COO - Founder Cruquiuskade 47 | | +31(0)851119172 Amsterdam 1018 AM NL | | [`as] http://www.amarulasolutions.com |
Signature · 4 lines
| Michael Nazzareno Trimarchi Amarula Solutions BV | | COO - Founder Cruquiuskade 47 | | +31(0)851119172 Amsterdam 1018 AM NL | | [`as] http://www.amarulasolutions.com |
$ sudo dd if=idbloader.img of=/dev/sdd seek=64 $ sudo dd if=u-boot-dtb.img of=/dev/sdd seek=16384
Still nothing.
Quoted 87 lines · Michael Nazzareno Trimarchi
Hi
https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip/commits/master
make idbloader.img
Michael
Quoted 65 lines · Alexander von Gluck IV
Using master from
git://git.denx.de/u-boot.gitcommit
390183b58179ddaf986422f4d9446c596660f7e0(HEAD -> master, origin/master, origin/HEAD)
Merge:d6c7309f5679907a4f84
Author: Tom Rini <[email protected]>
Date: Sat Sep 21 07:31:23 2019 -0400Merge tag 'efi-2019-10-rc4-5' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for v2019.10-rc4 (5)
This patch set fixes errors in the UEFI sub-system and adds a function to compare u16 strings which is prerequisite for further patches.
Same error:
$ ./tools/mkimage -n rk3288 -T rksd -d spl/u-boot-spl-dtb.bin out Warning: SPL image is too large (size 0xb000) and will not boot Error: image verification failed$ ls -lah spl/u-boot-spl-dtb.bin -rw-rw-r-- 1 kallisti5 kallisti5 43K Sep 22 16:17 spl/u-boot-spl-dtb.binSeptember 22, 2019 4:03 PM, "Michael Nazzareno Trimarchi" <[email protected]> wrote:
Hi
Please use the latest uboot. The fixes should be already merged
Mcihael
On Sun, Sep 22, 2019 at 10:53 PM Alexander von Gluck IV <[email protected]> wrote:
Anyone know a way to get a functional u-boot on the rk3288? (Tinkerboard, SD)
The docs seem to recommend:
$ /tmp/arm-build/tools/mkimage -n rk3288 -T rksd -d arm/tinkerboard/u-boot-spl-dtb.bin outHowever, that produces:
Warning: SPL image is too large (size0xb000) and will not bootI saw this patch to disable I2C in the SPL to reduce its size:
https://github.com/xypron/u-boot-patches/blob/df2ceb65fb4cc433aa17304ed9d3d591c14ef5ac/0001-configs-
inker-rk3288-disable-CONFIG_SPL_I2C_SUPPORT.patchHowever, that breaks the build :-|
LD spl/u-boot-spl
arm-unknown-haiku-ld.bfd:drivers/built-in.o: in function `rk8xx_write':/tmp/arm-build/drivers/power/pmic/rk8xx.c:30: undefined reference todm_i2c_write' arm-unknown-haiku-ld.bfd: drivers/built-in.o: in functionrk8xx_read':/tmp/arm-build/drivers/power/pmic/rk8xx.c:43: undefined reference to `dm_i2c_read' make[1]: *** [scripts/Makefile.spl:404: spl/u-boot-spl] Error 1
make: *** [Makefile:1762: spl/u-boot-spl] Error 2
make: Leaving directory '/tmp/arm-build'
Disabling SPL Power then results in an error compiling MMC support
Any alternative methods to getting u-boot running from SD?
Rockchip devices seem to be kind of complex to get going :-|
-- Alex
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-bootQuoted 5 lines
--
| Michael Nazzareno Trimarchi Amarula Solutions BV | | COO - Founder Cruquiuskade 47 | | +31(0)851119172 Amsterdam 1018 AM NL | | [`as] http://www.amarulasolutions.com |--
| Michael Nazzareno Trimarchi Amarula Solutions BV | | COO - Founder Cruquiuskade 47 | | +31(0)851119172 Amsterdam 1018 AM NL | | [`as] http://www.amarulasolutions.com |
Sorry for spam, reposting with more context :-)
$ make clean $ make tinker-rk3288_defconfig $ ARCH=arm CROSS_COMPILE=$TOOLCHAIN/bin/arm-unknown-haiku- make -j2
$ sudo dd if=idbloader.img of=/dev/sdd seek=64 $ sudo dd if=u-boot-dtb.img of=/dev/sdd seek=16384
I can confirm this toolchain successfully builds working u-boots for 4 other 32-bit arm boards. (gcc version 8.3.0 (GCC))
Quoted 98 lines · Alexander von Gluck IV
$ sudo dd if=idbloader.img of=/dev/sdd seek=64 $ sudo dd if=u-boot-dtb.img of=/dev/sdd seek=16384Still nothing.
Quoted 10 lines · Michael Nazzareno Trimarchi
Hi
https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip/commits/master
make idbloader.img
Michael
On Sun, Sep 22, 2019 at 11:22 PM Alexander von Gluck IV <[email protected]> wrote:
Using master from
git://git.denx.de/u-boot.gitcommit
390183b58179ddaf986422f4d9446c596660f7e0(HEAD -> master, origin/master, origin/HEAD)
Merge:d6c7309f5679907a4f84
Author: Tom Rini <[email protected]>
Date: Sat Sep 21 07:31:23 2019 -0400Merge tag 'efi-2019-10-rc4-5' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for v2019.10-rc4 (5)
This patch set fixes errors in the UEFI sub-system and adds a function to compare u16 strings which is prerequisite for further patches.
Same error:
$ ./tools/mkimage -n rk3288 -T rksd -d spl/u-boot-spl-dtb.bin out Warning: SPL image is too large (size 0xb000) and will not boot Error: image verification failed$ ls -lah spl/u-boot-spl-dtb.bin -rw-rw-r-- 1 kallisti5 kallisti5 43K Sep 22 16:17 spl/u-boot-spl-dtb.binSeptember 22, 2019 4:03 PM, "Michael Nazzareno Trimarchi" <[email protected]> wrote:
Hi
Please use the latest uboot. The fixes should be already merged
Mcihael
On Sun, Sep 22, 2019 at 10:53 PM Alexander von Gluck IV <[email protected]> wrote:
Anyone know a way to get a functional u-boot on the rk3288? (Tinkerboard, SD)
The docs seem to recommend:
$ /tmp/arm-build/tools/mkimage -n rk3288 -T rksd -d arm/tinkerboard/u-boot-spl-dtb.bin outHowever, that produces:
Warning: SPL image is too large (size0xb000) and will not bootI saw this patch to disable I2C in the SPL to reduce its size:
https://github.com/xypron/u-boot-patches/blob/df2ceb65fb4cc433aa17304ed9d3d591c14ef5ac/0001-configs-
inker-rk3288-disable-CONFIG_SPL_I2C_SUPPORT.patchHowever, that breaks the build :-|
LD spl/u-boot-spl
arm-unknown-haiku-ld.bfd:drivers/built-in.o: in function `rk8xx_write':/tmp/arm-build/drivers/power/pmic/rk8xx.c:30: undefined reference todm_i2c_write' arm-unknown-haiku-ld.bfd: drivers/built-in.o: in functionrk8xx_read':/tmp/arm-build/drivers/power/pmic/rk8xx.c:43: undefined reference to `dm_i2c_read' make[1]: *** [scripts/Makefile.spl:404: spl/u-boot-spl] Error 1
make: *** [Makefile:1762: spl/u-boot-spl] Error 2
make: Leaving directory '/tmp/arm-build'
Disabling SPL Power then results in an error compiling MMC support
Any alternative methods to getting u-boot running from SD?
Rockchip devices seem to be kind of complex to get going :-|
-- Alex
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot--
| Michael Nazzareno Trimarchi Amarula Solutions BV | | COO - Founder Cruquiuskade 47 | | +31(0)851119172 Amsterdam 1018 AM NL | | [`as] http://www.amarulasolutions.com |Quoted 5 lines
--
| Michael Nazzareno Trimarchi Amarula Solutions BV | | COO - Founder Cruquiuskade 47 | | +31(0)851119172 Amsterdam 1018 AM NL | | [`as] http://www.amarulasolutions.com |_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot
[U-Boot] rk3288 (Tinkerboard) not booting【请注意,邮件由[email protected]代发】
In reply to Alexander von Gluck IVHi Alexander,
The tinker board already enable TPL, so it should be use TPL
instead of SPL with mkimage tool.
The idbloader should have including both, if the idbloader boot fail, could you share the boot log?
Thanks,
- Kever
Quoted 78 lines · Alexander von Gluck IV
Using master from
git://git.denx.de/u-boot.gitcommit
390183b58179ddaf986422f4d9446c596660f7e0(HEAD -> master, origin/master, origin/HEAD)
Merge:d6c7309f5679907a4f84
Author: Tom Rini <[email protected]>
Date: Sat Sep 21 07:31:23 2019 -0400Merge tag 'efi-2019-10-rc4-5' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for v2019.10-rc4 (5)
This patch set fixes errors in the UEFI sub-system and adds a function to compare u16 strings which is prerequisite for further patches.
Same error:
$ ./tools/mkimage -n rk3288 -T rksd -d spl/u-boot-spl-dtb.bin out Warning: SPL image is too large (size 0xb000) and will not boot Error: image verification failed$ ls -lah spl/u-boot-spl-dtb.bin -rw-rw-r-- 1 kallisti5 kallisti5 43K Sep 22 16:17 spl/u-boot-spl-dtb.binQuoted 39 lines · Michael Nazzareno Trimarchi
Hi
Please use the latest uboot. The fixes should be already merged
Mcihael
Quoted 14 lines · Alexander von Gluck IV
Anyone know a way to get a functional u-boot on the rk3288? (Tinkerboard, SD)
The docs seem to recommend:
$ /tmp/arm-build/tools/mkimage -n rk3288 -T rksd -d arm/tinkerboard/u-boot-spl-dtb.bin outHowever, that produces:
Warning: SPL image is too large (size0xb000) and will not bootI saw this patch to disable I2C in the SPL to reduce its size:
https://github.com/xypron/u-boot-patches/blob/df2ceb65fb4cc433aa17304ed9d3d591c14ef5ac/0001-configs-
inker-rk3288-disable-CONFIG_SPL_I2C_SUPPORT.patchHowever, that breaks the build :-|
Quoted 16 lines
LD spl/u-boot-spl
arm-unknown-haiku-ld.bfd:drivers/built-in.o: in function `rk8xx_write':/tmp/arm-build/drivers/power/pmic/rk8xx.c:30: undefined reference todm_i2c_write' arm-unknown-haiku-ld.bfd: drivers/built-in.o: in functionrk8xx_read':/tmp/arm-build/drivers/power/pmic/rk8xx.c:43: undefined reference to `dm_i2c_read' make[1]: *** [scripts/Makefile.spl:404: spl/u-boot-spl] Error 1
make: *** [Makefile:1762: spl/u-boot-spl] Error 2
make: Leaving directory '/tmp/arm-build'
Disabling SPL Power then results in an error compiling MMC support
Any alternative methods to getting u-boot running from SD?
Rockchip devices seem to be kind of complex to get going :-|
-- Alex
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-bootQuoted 5 lines
--
| Michael Nazzareno Trimarchi Amarula Solutions BV | | COO - Founder Cruquiuskade 47 | | +31(0)851119172 Amsterdam 1018 AM NL | | [`as] http://www.amarulasolutions.com |_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot
[U-Boot] rk3288 (Tinkerboard) not booting【请注意,邮件由[email protected]代发】
Hello!
There is no uart output and no video with u-boot master. The board works as expected booting the Asus Armbian image on an SD.
At this point i'd be happy to get some u-boot uart output :-)
-- Alex
Quoted 82 lines · Kever Yang
Hi Alexander,
The tinker board already enable TPL, so it should be use TPL instead of SPL with mkimage tool.
The idbloader should have including both, if the idbloader boot fail, could you share the boot log?
Thanks,
- KeverQuoted 72 lines · Alexander von Gluck IV
Using master from
git://git.denx.de/u-boot.gitcommit
390183b58179ddaf986422f4d9446c596660f7e0(HEAD -> master, origin/master, origin/HEAD)
Merge:d6c7309f5679907a4f84
Author: Tom Rini <[email protected]>
Date: Sat Sep 21 07:31:23 2019 -0400Merge tag 'efi-2019-10-rc4-5' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Quoted 2 lines
Pull request for UEFI sub-system for v2019.10-rc4 (5)
This patch set fixes errors in the UEFI sub-system and adds a function tocompare u16 strings which is prerequisite for further patches.
Same error:
$ ./tools/mkimage -n rk3288 -T rksd -d spl/u-boot-spl-dtb.bin out Warning: SPL image is too large (size 0xb000) and will not boot Error: image verification failed$ ls -lah spl/u-boot-spl-dtb.bin -rw-rw-r-- 1 kallisti5 kallisti5 43K Sep 22 16:17 spl/u-boot-spl-dtb.binQuoted 8 lines · Michael Nazzareno Trimarchi
Hi
Please use the latest uboot. The fixes should be already merged
Mcihael
On Sun, Sep 22, 2019 at 10:53 PM Alexander von Gluck IV <[email protected]> wrote:
Anyone know a way to get a functional u-boot on the rk3288? (Tinkerboard, SD)
The docs seem to recommend:
$ /tmp/arm-build/tools/mkimage -n rk3288 -T rksd -d arm/tinkerboard/u-boot-spl-dtb.bin outHowever, that produces:
Warning: SPL image is too large (size0xb000) and will not bootI saw this patch to disable I2C in the SPL to reduce its size:
https://github.com/xypron/u-boot-patches/blob/df2ceb65fb4cc433aa17304ed9d3d591c14ef5ac/0001-configs-
inker-rk3288-disable-CONFIG_SPL_I2C_SUPPORT.patchHowever, that breaks the build :-|
LD spl/u-boot-spl
arm-unknown-haiku-ld.bfd:drivers/built-in.o: in function `rk8xx_write':/tmp/arm-build/drivers/power/pmic/rk8xx.c:30: undefined reference todm_i2c_write' arm-unknown-haiku-ld.bfd: drivers/built-in.o: in functionrk8xx_read':/tmp/arm-build/drivers/power/pmic/rk8xx.c:43: undefined reference to `dm_i2c_read' make[1]: *** [scripts/Makefile.spl:404: spl/u-boot-spl] Error 1
make: *** [Makefile:1762: spl/u-boot-spl] Error 2
make: Leaving directory '/tmp/arm-build'
Disabling SPL Power then results in an error compiling MMC support
Any alternative methods to getting u-boot running from SD?
Rockchip devices seem to be kind of complex to get going :-|
-- Alex
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-bootQuoted 5 lines
--
| Michael Nazzareno Trimarchi Amarula Solutions BV | | COO - Founder Cruquiuskade 47 | | +31(0)851119172 Amsterdam 1018 AM NL | | [`as] http://www.amarulasolutions.com |_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot
[U-Boot] rk3288 (Tinkerboard) not booting【请注意,邮件由[email protected]代发】
Quoted 8 lines · Alexander von Gluck IV
Hello!
There is no uart output and no video with u-boot master. The board works as expected booting the Asus Armbian image on an SD.
At this point i'd be happy to get some u-boot uart output :-)
-- Alex
uart output works here with the latest master
(780a17e814503f71d1b51d578b32bc9c89933183)
U-Boot TPL 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20) Trying to boot from BOOTROM
Returning to boot ROM...
U-Boot SPL 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20 +1000) Trying to boot from MMC1
U-Boot 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20 +1000)
Model: Tinker-RK3288 DRAM: 2 GiB MMC: dwmmc at ff0c0000: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environment
In: serial Out: serial Err: serial Model: Tinker-RK3288 rockchip_dnl_key_pressed: adc_channel_single_shot fail! Net: eth0: ethernet at ff290000 Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc1 is current device
Scanning mmc 1:1...
Found EFI removable media binary efi/boot/bootarm.efi libfdt fdt_check_header(): FDT_ERR_BADMAGIC Scanning disk dwmmc at ff0c0000.blk...
Found 3 disks
BootOrder not defined
EFI boot manager: Cannot load any image
88176 bytes read in 9 ms (9.3 MiB/s)
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
Quoted 1 line
Quoted 1 line
OpenBSD/armv7 BOOTARM 1.6
boot>
[U-Boot] rk3288 (Tinkerboard) not booting【请注意,邮件由[email protected]代发】
Ok, looking for differences now..
* Older Tinker Board? (I'm not using the Tinker Board S)
* Same steps?
* Same config? tinker-rk3288_defconfig?
* Uart 115200?
* Any HDMI Video output?
* GCC version?
Quoted 49 lines · Jonathan Gray
Quoted 8 lines · Alexander von Gluck IV
Hello!
There is no uart output and no video with u-boot master. The board works as expected booting the Asus Armbian image on an SD.
At this point i'd be happy to get some u-boot uart output :-)
-- Alex
uart output works here with the latest master
(780a17e814503f71d1b51d578b32bc9c89933183)U-Boot TPL 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20) Trying to boot from BOOTROM
Returning to boot ROM...U-Boot SPL 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20 +1000) Trying to boot from MMC1
U-Boot 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20 +1000)
Model: Tinker-RK3288
DRAM: 2 GiB
MMC: dwmmc atff0c0000: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environmentIn: serial
Out: serial
Err: serial
Model: Tinker-RK3288rockchip_dnl_key_pressed:adc_channel_single_shotfail!
Net: eth0: ethernet atff290000
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc1 is current device
Scanning mmc 1:1...
Found EFI removable media binary efi/boot/bootarm.efi libfdtfdt_check_header():FDT_ERR_BADMAGICScanning disk dwmmc at ff0c0000.blk...
Found 3 disks
BootOrder not defined
EFI boot manager: Cannot load any image
88176 bytes read in 9 ms (9.3 MiB/s)
libfdtfdt_check_header():FDT_ERR_BADMAGICQuoted 1 line
Quoted 1 line
OpenBSD/armv7 BOOTARM 1.6
boot>
[U-Boot] rk3288 (Tinkerboard) not booting【请注意,邮件由[email protected]代发】
Quoted 3 lines · Alexander von Gluck IV
Ok, looking for differences now..
* Older Tinker Board? (I'm not using the Tinker Board S)
yes, the original one
Quoted 1 line
* Same steps?
along the lines of
gmake CROSS_COMPILE="arm-none-eabi-" tinker-rk3288_defconfig gmake CROSS_COMPILE="arm-none-eabi-" alltools/mkimage -n rk3288 -T rksd -d tpl/u-boot-tpl.bin idbloader.img && \
cat spl/u-boot-spl-dtb.bin >> idbloader.img
Quoted 1 line
* Same config? tinker-rk3288_defconfig?
yes
Quoted 1 line
* Uart 115200?
yes
Quoted 1 line
* Any HDMI Video output?
no hdmi connected only serial
Quoted 1 line
* GCC version?
gcc-linaro-6.3.2017.02 binutils 2.27 arm-none-eabi target
Quoted 56 lines
Quoted 46 lines · Jonathan Gray
Quoted 8 lines · Alexander von Gluck IV
Hello!
There is no uart output and no video with u-boot master. The board works as expected booting the Asus Armbian image on an SD.
At this point i'd be happy to get some u-boot uart output :-)
-- Alex
uart output works here with the latest master
(780a17e814503f71d1b51d578b32bc9c89933183)U-Boot TPL 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20) Trying to boot from BOOTROM
Returning to boot ROM...U-Boot SPL 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20 +1000) Trying to boot from MMC1
U-Boot 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20 +1000)
Model: Tinker-RK3288
DRAM: 2 GiB
MMC: dwmmc atff0c0000: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environmentIn: serial
Out: serial
Err: serial
Model: Tinker-RK3288rockchip_dnl_key_pressed:adc_channel_single_shotfail!
Net: eth0: ethernet atff290000
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc1 is current device
Scanning mmc 1:1...
Found EFI removable media binary efi/boot/bootarm.efi libfdtfdt_check_header():FDT_ERR_BADMAGICScanning disk dwmmc at ff0c0000.blk...
Found 3 disks
BootOrder not defined
EFI boot manager: Cannot load any image
88176 bytes read in 9 ms (9.3 MiB/s)
libfdtfdt_check_header():FDT_ERR_BADMAGICQuoted 3 lines
Quoted 1 line
Quoted 1 line
OpenBSD/armv7 BOOTARM 1.6
boot>
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot
[U-Boot] rk3288 (Tinkerboard) not booting【请注意,邮件由[email protected]代发】
Oh, a difference:
$ tools/mkimage -n rk3288 -T rksd -d tpl/u-boot-tpl.bin idbloader.img && \
cat spl/u-boot-spl-dtb.bin >> idbloader.imgI'm using the idbloader.img that u-boot automatically spits out.
$ tools/mkimage -n rk3288 -T rksd -d tpl/u-boot-tpl.bin idbloader-manual.img Image Type: Rockchip RK32 (SD/MMC) boot image Data Size: 20480 bytes $ cat spl/u-boot-spl-dtb.bin >> idbloader-manual.img
However.. the generated idbloader-manual.img from the commands above is identical to idbloader.img that u-boot produces compared with md5sum.
Are you writing the following?
sudo dd if=idbloader.img of=/dev/sdd seek=64 sudo dd if=u-boot-dtb.img of=/dev/sdd seek=16384
(where /dev/sdd is a MicroSD card)
These should be enough to get into u-boot at startup... correct?
I'm not missing some requirement of u-boot.bin on a FAT32 partition or something?
-- Alex
Quoted 88 lines · Jonathan Gray
Quoted 3 lines · Alexander von Gluck IV
Ok, looking for differences now..
* Older Tinker Board? (I'm not using the Tinker Board S)
yes, the original one
Quoted 1 line
* Same steps?
along the lines of
gmake CROSS_COMPILE="arm-none-eabi-" tinker-rk3288_defconfig gmake CROSS_COMPILE="arm-none-eabi-" all
tools/mkimage-n rk3288 -T rksd -d tpl/u-boot-tpl.bin idbloader.img && \
cat spl/u-boot-spl-dtb.bin >> idbloader.imgQuoted 1 line
* Same config? tinker-rk3288_defconfig?
yes
Quoted 1 line
* Uart 115200?
yes
Quoted 1 line
* Any HDMI Video output?
no hdmi connected only serial
Quoted 1 line
* GCC version?
gcc-linaro-6.3.2017.02 binutils 2.27 arm-none-eabi target
Quoted 55 lines
September 23, 2019 12:34 AM, "Jonathan Gray" <[email protected]> wrote:
On Mon, Sep 23, 2019 at 01:17:40AM +0000, Alexander von Gluck IV wrote:
Hello!
There is no uart output and no video with u-boot master. The board works as expected booting the Asus Armbian image on an SD.
At this point i'd be happy to get some u-boot uart output :-)
-- Alex
uart output works here with the latest master
(780a17e814503f71d1b51d578b32bc9c89933183)U-Boot TPL 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20) Trying to boot from BOOTROM
Returning to boot ROM...U-Boot SPL 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20 +1000) Trying to boot from MMC1
U-Boot 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20 +1000)
Model: Tinker-RK3288
DRAM: 2 GiB
MMC: dwmmc atff0c0000: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environmentIn: serial
Out: serial
Err: serial
Model: Tinker-RK3288rockchip_dnl_key_pressed:adc_channel_single_shotfail!
Net: eth0: ethernet atff290000
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc1 is current device
Scanning mmc 1:1...
Found EFI removable media binary efi/boot/bootarm.efi libfdtfdt_check_header():FDT_ERR_BADMAGICScanning disk dwmmc at ff0c0000.blk...
Found 3 disks
BootOrder not defined
EFI boot manager: Cannot load any image
88176 bytes read in 9 ms (9.3 MiB/s)
libfdtfdt_check_header():FDT_ERR_BADMAGICOpenBSD/armv7 BOOTARM 1.6boot>
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot
[U-Boot] rk3288 (Tinkerboard) not booting【请注意,邮件由[email protected]代发】
Quoted 12 lines · Alexander von Gluck IV
Oh, a difference:
$ tools/mkimage -n rk3288 -T rksd -d tpl/u-boot-tpl.bin idbloader.img && \ cat spl/u-boot-spl-dtb.bin >> idbloader.imgI'm using the idbloader.img that u-boot automatically spits out.
$ tools/mkimage -n rk3288 -T rksd -d tpl/u-boot-tpl.bin idbloader-manual.img Image Type: Rockchip RK32 (SD/MMC) boot image Data Size: 20480 bytes $ cat spl/u-boot-spl-dtb.bin >> idbloader-manual.img
Quoted 8 lines
However.. the generated idbloader-manual.img from the commands above is identical to idbloader.img that u-boot produces compared with md5sum.
Are you writing the following?
sudo dd if=idbloader.img of=/dev/sdd seek=64 sudo dd if=u-boot-dtb.img of=/dev/sdd seek=16384
those files/offsets yes
Quoted 4 lines
(where
/dev/sddis a MicroSD card)These should be enough to get into u-boot at startup... correct?
yes
I am using uart2
https://www.asus.com/us/Single-Board-Computer/Tinker-Board/
32 UART2TX_PWM3
33 UART2RX_PWM2
and 30 for ground
Quoted 2 lines
I'm not missing some requirement of u-boot.bin on a FAT32 partition or something?
the tpl/spl and u-boot proper are at raw offsets in this case
Quoted 93 lines
-- Alex
Quoted 88 lines · Jonathan Gray
Quoted 3 lines · Alexander von Gluck IV
Ok, looking for differences now..
* Older Tinker Board? (I'm not using the Tinker Board S)
yes, the original one
Quoted 1 line
* Same steps?
along the lines of
gmake CROSS_COMPILE="arm-none-eabi-" tinker-rk3288_defconfig gmake CROSS_COMPILE="arm-none-eabi-" all
tools/mkimage-n rk3288 -T rksd -d tpl/u-boot-tpl.bin idbloader.img && \
cat spl/u-boot-spl-dtb.bin >> idbloader.imgQuoted 1 line
* Same config? tinker-rk3288_defconfig?
yes
Quoted 1 line
* Uart 115200?
yes
Quoted 1 line
* Any HDMI Video output?
no hdmi connected only serial
Quoted 1 line
* GCC version?
gcc-linaro-6.3.2017.02 binutils 2.27 arm-none-eabi target
Quoted 55 lines
September 23, 2019 12:34 AM, "Jonathan Gray" <[email protected]> wrote:
On Mon, Sep 23, 2019 at 01:17:40AM +0000, Alexander von Gluck IV wrote:
Hello!
There is no uart output and no video with u-boot master. The board works as expected booting the Asus Armbian image on an SD.
At this point i'd be happy to get some u-boot uart output :-)
-- Alex
uart output works here with the latest master
(780a17e814503f71d1b51d578b32bc9c89933183)U-Boot TPL 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20) Trying to boot from BOOTROM
Returning to boot ROM...U-Boot SPL 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20 +1000) Trying to boot from MMC1
U-Boot 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20 +1000)
Model: Tinker-RK3288
DRAM: 2 GiB
MMC: dwmmc atff0c0000: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environmentIn: serial
Out: serial
Err: serial
Model: Tinker-RK3288rockchip_dnl_key_pressed:adc_channel_single_shotfail!
Net: eth0: ethernet atff290000
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc1 is current device
Scanning mmc 1:1...
Found EFI removable media binary efi/boot/bootarm.efi libfdtfdt_check_header():FDT_ERR_BADMAGICScanning disk dwmmc at ff0c0000.blk...
Found 3 disks
BootOrder not defined
EFI boot manager: Cannot load any image
88176 bytes read in 9 ms (9.3 MiB/s)
libfdtfdt_check_header():FDT_ERR_BADMAGICOpenBSD/armv7 BOOTARM 1.6boot>
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot
[U-Boot] rk3288 (Tinkerboard) not booting【请注意,邮件由[email protected]代发】
ACK! I'm on UART1. Mix that with video potentially not working in u-boot and I think I have my answer.
I'll test this afternoon.
(PS, since the Tinker is supposed to be "Raspberry Pi like", why would u-boot present on UART2 on it while the Raspberry Pi u-boot uses UART1?)
Thanks for the help!
-- Alex
Quoted 132 lines · Jonathan Gray
Quoted 12 lines · Alexander von Gluck IV
Oh, a difference:
$ tools/mkimage -n rk3288 -T rksd -d tpl/u-boot-tpl.bin idbloader.img && \ cat spl/u-boot-spl-dtb.bin >> idbloader.imgI'm using the idbloader.img that u-boot automatically spits out.
$ tools/mkimage -n rk3288 -T rksd -d tpl/u-boot-tpl.bin idbloader-manual.img Image Type: Rockchip RK32 (SD/MMC) boot image Data Size: 20480 bytes $ cat spl/u-boot-spl-dtb.bin >> idbloader-manual.imgQuoted 7 lines
However.. the generated idbloader-manual.img from the commands above is identical to idbloader.img that u-boot produces compared with md5sum.
Are you writing the following?
sudo dd if=idbloader.img of=/dev/sdd seek=64
sudo dd if=u-boot-dtb.img of=/dev/sdd seek=16384those files/offsets yes
Quoted 3 lines
(where
/dev/sddis a MicroSD card)These should be enough to get into u-boot at startup... correct?
yes
I am using uart2
https://www.asus.com/us/Single-Board-Computer/Tinker-Board
32UART2TX_PWM3
33UART2RX_PWM2
and 30 for groundQuoted 1 line
I'm not missing some requirement of u-boot.bin on a FAT32 partition or something?
the tpl/spl and u-boot proper are at raw offsets in this case
Quoted 92 lines
-- Alex
September 23, 2019 8:31 AM, "Jonathan Gray" <[email protected]> wrote:
On Mon, Sep 23, 2019 at 01:06:35PM +0000, Alexander von Gluck IV wrote:
Ok, looking for differences now..
* Older Tinker Board? (I'm not using the Tinker Board S)
yes, the original one
* Same steps?
along the lines of
gmake CROSS_COMPILE="arm-none-eabi-" tinker-rk3288_defconfig gmake CROSS_COMPILE="arm-none-eabi-" all
tools/mkimage-n rk3288 -T rksd -d tpl/u-boot-tpl.bin idbloader.img && \
cat spl/u-boot-spl-dtb.bin >> idbloader.img* Same config? tinker-rk3288_defconfig?
yes
* Uart 115200?
yes
* Any HDMI Video output?
no hdmi connected only serial
* GCC version?
gcc-linaro-6.3.2017.02 binutils 2.27 arm-none-eabi target
September 23, 2019 12:34 AM, "Jonathan Gray" <[email protected]> wrote:
On Mon, Sep 23, 2019 at 01:17:40AM +0000, Alexander von Gluck IV wrote:
Hello!
There is no uart output and no video with u-boot master. The board works as expected booting the Asus Armbian image on an SD.
At this point i'd be happy to get some u-boot uart output :-)
-- Alex
uart output works here with the latest master
(780a17e814503f71d1b51d578b32bc9c89933183)U-Boot TPL 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20) Trying to boot from BOOTROM
Returning to boot ROM...U-Boot SPL 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20 +1000) Trying to boot from MMC1
U-Boot 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20 +1000)
Model: Tinker-RK3288
DRAM: 2 GiB
MMC: dwmmc atff0c0000: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environmentIn: serial
Out: serial
Err: serial
Model: Tinker-RK3288rockchip_dnl_key_pressed:adc_channel_single_shotfail!
Net: eth0: ethernet atff290000
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc1 is current device
Scanning mmc 1:1...
Found EFI removable media binary efi/boot/bootarm.efi libfdtfdt_check_header():FDT_ERR_BADMAGICScanning disk dwmmc at ff0c0000.blk...
Found 3 disks
BootOrder not defined
EFI boot manager: Cannot load any image
88176 bytes read in 9 ms (9.3 MiB/s)
libfdtfdt_check_header():FDT_ERR_BADMAGICOpenBSD/armv7 BOOTARM 1.6boot>
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot
[U-Boot] rk3288 (Tinkerboard) not booting【请注意,邮件由[email protected]代发】
Just rounding this one out.. I was definitely looking at the wrong uart. After moving to uart2, things are working as expected (minus hdmi output from u-boot)
Thanks!
-- Alex
Quoted 151 lines · Alexander von Gluck IV
ACK! I'm on UART1. Mix that with video potentially not working in u-boot and I think I have my answer.
I'll test this afternoon.
(PS, since the Tinker is supposed to be "Raspberry Pi like", why would u-boot present on UART2 on it while the Raspberry Pi u-boot uses UART1?)
Thanks for the help!
-- Alex
Quoted 36 lines · Jonathan Gray
Quoted 12 lines · Alexander von Gluck IV
Oh, a difference:
$ tools/mkimage -n rk3288 -T rksd -d tpl/u-boot-tpl.bin idbloader.img && \ cat spl/u-boot-spl-dtb.bin >> idbloader.imgI'm using the idbloader.img that u-boot automatically spits out.
$ tools/mkimage -n rk3288 -T rksd -d tpl/u-boot-tpl.bin idbloader-manual.img Image Type: Rockchip RK32 (SD/MMC) boot image Data Size: 20480 bytes $ cat spl/u-boot-spl-dtb.bin >> idbloader-manual.imgQuoted 7 lines
However.. the generated idbloader-manual.img from the commands above is identical to idbloader.img that u-boot produces compared with md5sum.
Are you writing the following?
sudo dd if=idbloader.img of=/dev/sdd seek=64
sudo dd if=u-boot-dtb.img of=/dev/sdd seek=16384those files/offsets yes
Quoted 3 lines
(where
/dev/sddis a MicroSD card)These should be enough to get into u-boot at startup... correct?
yes
I am using uart2
https://www.asus.com/us/Single-Board-Computer/Tinker-Board
32UART2TX_PWM3
33UART2RX_PWM2
and 30 for groundQuoted 96 lines
Quoted 1 line
I'm not missing some requirement of u-boot.bin on a FAT32 partition or something?
the tpl/spl and u-boot proper are at raw offsets in this case
Quoted 92 lines
-- Alex
September 23, 2019 8:31 AM, "Jonathan Gray" <[email protected]> wrote:
On Mon, Sep 23, 2019 at 01:06:35PM +0000, Alexander von Gluck IV wrote:
Ok, looking for differences now..
* Older Tinker Board? (I'm not using the Tinker Board S)
yes, the original one
* Same steps?
along the lines of
gmake CROSS_COMPILE="arm-none-eabi-" tinker-rk3288_defconfig gmake CROSS_COMPILE="arm-none-eabi-" all
tools/mkimage-n rk3288 -T rksd -d tpl/u-boot-tpl.bin idbloader.img && \
cat spl/u-boot-spl-dtb.bin >> idbloader.img* Same config? tinker-rk3288_defconfig?
yes
* Uart 115200?
yes
* Any HDMI Video output?
no hdmi connected only serial
* GCC version?
gcc-linaro-6.3.2017.02 binutils 2.27 arm-none-eabi target
September 23, 2019 12:34 AM, "Jonathan Gray" <[email protected]> wrote:
On Mon, Sep 23, 2019 at 01:17:40AM +0000, Alexander von Gluck IV wrote:
Hello!
There is no uart output and no video with u-boot master. The board works as expected booting the Asus Armbian image on an SD.
At this point i'd be happy to get some u-boot uart output :-)
-- Alex
uart output works here with the latest master
(780a17e814503f71d1b51d578b32bc9c89933183)U-Boot TPL 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20) Trying to boot from BOOTROM
Returning to boot ROM...U-Boot SPL 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20 +1000) Trying to boot from MMC1
U-Boot 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20 +1000)
Model: Tinker-RK3288
DRAM: 2 GiB
MMC: dwmmc atff0c0000: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environmentIn: serial
Out: serial
Err: serial
Model: Tinker-RK3288rockchip_dnl_key_pressed:adc_channel_single_shotfail!
Net: eth0: ethernet atff290000
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc1 is current device
Scanning mmc 1:1...
Found EFI removable media binary efi/boot/bootarm.efi libfdtfdt_check_header():FDT_ERR_BADMAGICScanning disk dwmmc at ff0c0000.blk...
Found 3 disks
BootOrder not defined
EFI boot manager: Cannot load any image
88176 bytes read in 9 ms (9.3 MiB/s)
libfdtfdt_check_header():FDT_ERR_BADMAGICOpenBSD/armv7 BOOTARM 1.6boot>
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot
[U-Boot] rk3288 (Tinkerboard) not booting【请注意,邮件由[email protected]代发】
Hi
Quoted 3 lines · Alexander von Gluck IV
Just rounding this one out.. I was definitely looking at the wrong uart. After moving to uart2, things are working as expected (minus hdmi output from u-boot)
This can be enabled, but it's not the default on tinker
Michael
Quoted 161 lines
Thanks!
-- Alex
Quoted 147 lines · Alexander von Gluck IV
ACK! I'm on UART1. Mix that with video potentially not working in u-boot and I think I have my answer.
I'll test this afternoon.
(PS, since the Tinker is supposed to be "Raspberry Pi like", why would u-boot present on UART2 on it while the Raspberry Pi u-boot uses UART1?)
Thanks for the help!
-- Alex
Quoted 36 lines · Jonathan Gray
Quoted 12 lines · Alexander von Gluck IV
Oh, a difference:
$ tools/mkimage -n rk3288 -T rksd -d tpl/u-boot-tpl.bin idbloader.img && \ cat spl/u-boot-spl-dtb.bin >> idbloader.imgI'm using the idbloader.img that u-boot automatically spits out.
$ tools/mkimage -n rk3288 -T rksd -d tpl/u-boot-tpl.bin idbloader-manual.img Image Type: Rockchip RK32 (SD/MMC) boot image Data Size: 20480 bytes $ cat spl/u-boot-spl-dtb.bin >> idbloader-manual.imgQuoted 7 lines
However.. the generated idbloader-manual.img from the commands above is identical to idbloader.img that u-boot produces compared with md5sum.
Are you writing the following?
sudo dd if=idbloader.img of=/dev/sdd seek=64
sudo dd if=u-boot-dtb.img of=/dev/sdd seek=16384those files/offsets yes
Quoted 3 lines
(where
/dev/sddis a MicroSD card)These should be enough to get into u-boot at startup... correct?
yes
I am using uart2
https://www.asus.com/us/Single-Board-Computer/Tinker-Board
32UART2TX_PWM3
33UART2RX_PWM2
and 30 for groundQuoted 96 lines
Quoted 1 line
I'm not missing some requirement of u-boot.bin on a FAT32 partition or something?
the tpl/spl and u-boot proper are at raw offsets in this case
Quoted 92 lines
-- Alex
September 23, 2019 8:31 AM, "Jonathan Gray" <[email protected]> wrote:
On Mon, Sep 23, 2019 at 01:06:35PM +0000, Alexander von Gluck IV wrote:
Ok, looking for differences now..
* Older Tinker Board? (I'm not using the Tinker Board S)
yes, the original one
* Same steps?
along the lines of
gmake CROSS_COMPILE="arm-none-eabi-" tinker-rk3288_defconfig gmake CROSS_COMPILE="arm-none-eabi-" all
tools/mkimage-n rk3288 -T rksd -d tpl/u-boot-tpl.bin idbloader.img && \
cat spl/u-boot-spl-dtb.bin >> idbloader.img* Same config? tinker-rk3288_defconfig?
yes
* Uart 115200?
yes
* Any HDMI Video output?
no hdmi connected only serial
* GCC version?
gcc-linaro-6.3.2017.02 binutils 2.27 arm-none-eabi target
September 23, 2019 12:34 AM, "Jonathan Gray" <[email protected]> wrote:
On Mon, Sep 23, 2019 at 01:17:40AM +0000, Alexander von Gluck IV wrote:
Hello!
There is no uart output and no video with u-boot master. The board works as expected booting the Asus Armbian image on an SD.
At this point i'd be happy to get some u-boot uart output :-)
-- Alex
uart output works here with the latest master
(780a17e814503f71d1b51d578b32bc9c89933183)U-Boot TPL 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20) Trying to boot from BOOTROM
Returning to boot ROM...U-Boot SPL 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20 +1000) Trying to boot from MMC1
U-Boot 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20 +1000)
Model: Tinker-RK3288
DRAM: 2 GiB
MMC: dwmmc atff0c0000: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environmentIn: serial
Out: serial
Err: serial
Model: Tinker-RK3288rockchip_dnl_key_pressed:adc_channel_single_shotfail!
Net: eth0: ethernet atff290000
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc1 is current device
Scanning mmc 1:1...
Found EFI removable media binary efi/boot/bootarm.efi libfdtfdt_check_header():FDT_ERR_BADMAGICScanning disk dwmmc at ff0c0000.blk...
Found 3 disks
BootOrder not defined
EFI boot manager: Cannot load any image
88176 bytes read in 9 ms (9.3 MiB/s)
libfdtfdt_check_header():FDT_ERR_BADMAGICOpenBSD/armv7 BOOTARM 1.6boot>
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-bootQuoted 4 lines
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
https://lists.denx.de/listinfo/u-boot
Signature · 4 lines
| Michael Nazzareno Trimarchi Amarula Solutions BV | | COO - Founder Cruquiuskade 47 | | +31(0)851119172 Amsterdam 1018 AM NL | | [`as] http://www.amarulasolutions.com |