Can't boot to initramfs
Hello,
I currently try to deploy a single rootfs update mechanism for my embedded device. I can't boot to initramfs using either "break" or "break=premount" (without quotes...). I tried this in systemd-boot and grub-efi (always efi boot) but the boot process just continues normally. If I insert at the same point e.g. "quiet" this argument is recognised. I boot the .wic image with a separate boot partition from a USB stick. in local.conf I have set:INITRAMFS_IMAGE = "core-image-minimal-initramfs" INITRAMFS_IMAGE_BUNDLE = "1"
In order to reduce complexity I now use the standard core-image-minimal-initramfs without .bbappend. I can confirm (from seeing the task) that bitbake bundled the kernel with the initramfs.
You can find the /var/log/dmesg here: https://pastebin.com/ya7iCtq7
To my understanding the initramfs should be embedded in /boot/bzImage. However since I use an intel platform I also have a /boot/microcode.cpio which gets loaded via "initrd /microcode.cpio". Removing this line in grub does not enable me to get an initramfs prompt either (again, using break as option).
Did I forget some configuration or do I have to put the break statement at a very specific position within the "linux ..." boot command ? Do you know which bitbake variables to check ? (both set in local.conf do not get overwritten, already checked this). I got the thud branch checked out in all my meta-layers except for meta-qt which is currently on master branch.
Help is much appreciated !
Best regards
Moritz
Quoted 2 lines
INITRAMFS_IMAGE= *"core-image-minimal-initramfs"*INITRAMFS_IMAGE_BUNDLE= "1"
...
Quoted 1 line
You can find the
/var/log/dmesghere: https://pastebin.com/ya7iCtq7I
Some hints...
[1] Kernel command line: BOOT_IMAGE=/bzImage root=PARTUUID=71d1d94a-83e8-4895-98eb-35309f58119f break=premount quiet rootwait rootwait rootfstype=ext4 *console=ttyS0,115200 console=tty0*
input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input7
fbcon: inteldrmfb (fb0) is primary device
Console: switching to colour frame buffer device 128x48 *i915 0000:00:02.0: fb0: inteldrmfb frame buffer device* snd_hda_intel 0000:00:1b.0: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915])
Hmmmmm... You are using console and serial, but full i915 GFX kernel driver is still included in the build???
[2] efi: EFI v2.31 by American Megatrends
Using AMI BIOS as boot loader FW... OK?! Am I correct?
[3] smpboot: CPU0: Intel(R) Atom(TM) CPU E3825 @ 1.33GHz (family: 0x6,
model: 0x37, stepping: 0x9)
This is CPUID ID 0x30679, which uses MCU... Which MicroCodeUnit? M0130679xxx (info from AMI BIOS)?
[4] Using INTEL ATOM BYT E3825 dual core (sans Hyper-threading), implies that you are using
4GB (e820 messages) as single channel (one memory module DDR3 as 4GB)! Am I correct (important)?
[5] Dracut phase?!
Quoted 5 lines
To my understanding the initramfs should be embedded in
/boot/bzImage. However since I use an intel platform I also have a/boot/microcode.cpiowhich gets loaded via "initrd /microcode.cpio". Removing this line in grub does not enable me to get an initramfs prompt either (again, using break as option).
You are obviously stopping in boot phase called dracut. Please, try to mount by hand
/dev/sda(whatever)... You should use fdisk -l command, or do ls -al /dev | grep sda to
dig out which partition you need to mount to /tmp dir to see rootfstype=ext4 (HDD/SSD)
_______
Just thinking loud... .. .
Hope this helps (has very little to do with YOCTO build system, BTW) . ;-)
Zoran
_______
Quoted 41 lines · Moritz Porst
Hello,
I currently try to deploy a single rootfs update mechanism for my embedded device. I can't boot to initramfs using either "break" or "break=premount" (without quotes...). I tried this in systemd-boot and grub-efi (always efi boot) but the boot process just continues normally. If I insert at the same point e.g. "quiet" this argument is recognised. I boot the .wic image with a separate boot partition from a USB stick. in local.conf I have set:INITRAMFS_IMAGE= "core-image-minimal-initramfs"INITRAMFS_IMAGE_BUNDLE= "1"In order to reduce complexity I now use the standard core-image-minimal-initramfs without .bbappend. I can confirm (from seeing the task) that bitbake bundled the kernel with the initramfs.
You can find the
/var/log/dmesghere: https://pastebin.com/ya7iCtq7To my understanding the initramfs should be embedded in
/boot/bzImage. However since I use an intel platform I also have a/boot/microcode.cpiowhich gets loaded via "initrd /microcode.cpio". Removing this line in grub does not enable me to get an initramfs prompt either (again, using break as option).Did I forget some configuration or do I have to put the break statement at a very specific position within the "linux ..." boot command ? Do you know which bitbake variables to check ? (both set in local.conf do not get overwritten, already checked this). I got the thud branch checked out in all my meta-layers except for meta-qt which is currently on master branch.
Help is much appreciated !
Best regards
Moritz--
_______________________________________________
yocto mailing list
[email protected]
https://lists.yoctoproject.org/listinfo/yocto
Hello Zoran,
thanks for your answer
Quoted 21 lines · Zoran Stojsavljevic
Quoted 2 lines
INITRAMFS_IMAGE= /*"core-image-minimal-initramfs"*/INITRAMFS_IMAGE_BUNDLE= "1"...
Quoted 1 line
You can find the
/var/log/dmesghere: https://pastebin.com/ya7iCtq7ISome hints...
[1] Kernel command line: BOOT_IMAGE=/bzImage root=PARTUUID=71d1d94a-83e8-4895-98eb-35309f58119f break=premount quiet rootwait rootwait rootfstype=ext4 /*console=ttyS0,115200 console=tty0*/
/*
*/
input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input7
fbcon: inteldrmfb (fb0) is primary device
Console: switching to colour frame buffer device 128x48 /*i915 0000:00:02.0: fb0: inteldrmfb frame buffer device*/snd_hda_intel0000:00:1b.0: bound 0000:00:02.0 (opsi915_audio_component_bind_ops[i915])
Quoted 2 lines
Hmmmmm... You are using console and serial, but full i915 GFX kernel driver is still included in the build???
I started from the core-image-minimal to have a small image and extended it with the features I need, which is e.g. a graphical system. The console=[...] part in the kernel command line is probably a remnant but my image boots into the GUI. Is this a problem ?
Quoted 5 lines
/*
*/
[2] efi: EFI v2.31 by American MegatrendsUsing AMI BIOS as boot loader FW... OK?! Am I correct?
My bootloader is currently grub, the EFI is AM.
Quoted 6 lines
[3] smpboot: CPU0: Intel(R) Atom(TM) CPU E3825 @ 1.33GHz (family:
0x6, model:0x37, stepping:0x9)This is CPUID ID
0x30679, which uses MCU... Which MicroCodeUnit? M0130679xxx (info from AMI BIOS)?
Sorry but I can't find this info in the EFI
Quoted 5 lines
[4] Using INTEL ATOM BYT E3825 dual core (sans Hyper-threading), implies that you are using
4GB (e820 messages) as single channel (one memory module DDR3 as 4GB)! Am I correct (important)?
2GB, single channel.
Quoted 8 lines
[5] Dracut phase?!
Quoted 5 lines
To my understanding the initramfs should be embedded in
/boot/bzImage. However since I use an intel platform I also have a/boot/microcode.cpiowhich gets loaded via "initrd /microcode.cpio". Removing this line in grub does not enable me to get an initramfs prompt either (again, using break as option).
Quoted 6 lines
You are obviously stopping in boot phase called dracut. Please, try to mount by hand
/dev/sda(whatever)... You should use fdisk -l command, or do ls -al /dev | grep sda to
dig out which partition you need to mount to /tmp dir to see rootfstype=ext4 (HDD/SSD)
No, the boot does not stop. Even if I do issue "break=premount" I end up in my graphical interface with the rootfs mounted. This is the last message in the log:
EXT4-fs (sdb2): re-mounted. Opts: (null)
The rootfs partition is always 2, so either /dev/sda2 or /dev/sdb2 (when booting from stick)
Quoted 60 lines
_______
Just thinking loud... .. .
Hope this helps (has very little to do with YOCTO build system, BTW) . ;-)
Zoran
_______On Fri, Jun 28, 2019 at 11:22 AM Moritz Porst <[email protected] <mailto:[email protected]>> wrote:
Hello,
I currently try to deploy a single rootfs update mechanism for my embedded device. I can't boot to initramfs using either "break" or "break=premount" (without quotes...). I tried this in systemd-boot and grub-efi (always efi boot) but the boot process just continues normally.
If I insert at the same point e.g. "quiet" this argument is recognised.
I boot the .wic image with a separate boot partition from a USB stick. in local.conf I have set:
INITRAMFS_IMAGE= "core-image-minimal-initramfs"INITRAMFS_IMAGE_BUNDLE= "1"In order to reduce complexity I now use the standard core-image-minimal-initramfs without .bbappend. I can confirm (from seeing the task) that bitbake bundled the kernel with the initramfs.
You can find the
/var/log/dmesghere: https://pastebin.com/ya7iCtq7To my understanding the initramfs should be embedded in
/boot/bzImage. However since I use an intel platform I also have a/boot/microcode.cpio
which gets loaded via "initrd /microcode.cpio". Removing this line in grub does not enable me to get an initramfs prompt either (again, using
break as option).Did I forget some configuration or do I have to put the break statement
at a very specific position within the "linux ..." boot command ? Do you
know which bitbake variables to check ? (both set in local.conf do not get overwritten, already checked this). I got the thud branch checked out in all my meta-layers except for meta-qt which is currently on master branch.Help is much appreciated !
Best regards
Moritz--
_______________________________________________
yocto mailing list
[email protected] <mailto:[email protected]>
https://lists.yoctoproject.org/listinfo/yocto
Hey,
So I have proceeded a tiny bit.
What I did was to copy the core-image-minimal-initramfs.cpio.gz to my /boot partition and boot using (EFI grub):
linux /bzimage
initrd /initramfs.cpio.gz
This way the boot process starts and at some point it says "can't find rootfs.img, dropping to a shell". It doesn't drop to a shell though... (busybox is included)
Booting without the initrd (or with initrd /microcode.cpio) results in a kernel panic. This leads me to the suspicion that meta-intel overwrites my initramfs (since microcode.cpio is present in boot) Further more think I shouldn't even be required to set initrd for boot since it should be embedded into the kernel ? (INITRAMFS_IMAGE_BUNDLE="1") I got the relevant variables from bitbake -e here, maybe someone more experienced can spot an error ?
# $INITRAMFS_FSTYPES [2 operations]
# set /opt/thudPoky/meta/conf/documentation.conf:228
# [doc] "Defines the format for the output image of an initial RAM disk (initramfs), which is used during boot."
# set? /opt/thudPoky/meta/conf/bitbake.conf:770
# "cpio.gz"
# pre-expansion value:
# "cpio.gz"
INITRAMFS_FSTYPES="cpio.gz"
#
# $INITRAMFS_IMAGE
# set /opt/thudPoky/build/conf/local.conf:257
# "core-image-minimal-initramfs"
INITRAMFS_IMAGE="core-image-minimal-initramfs"
#
# $INITRAMFS_IMAGE_BUNDLE
# set /opt/thudPoky/build/conf/local.conf:258
# "1"
INITRAMFS_IMAGE_BUNDLE="1"
#
# $INITRAMFS_MAXSIZE [2 operations]
# set /opt/thudPoky/meta-ccns5/conf/machine/ccns5.conf:34
# "200000"
# set /opt/thudPoky/meta/conf/bitbake.conf:774
# [_defaultval] "131072"
# pre-expansion value:
# "200000"
INITRAMFS_MAXSIZE="200000"
#
# $INITRD
# set /opt/thudPoky/meta/conf/documentation.conf:229
# [doc] "Indicates a list of filesystem images to concatenate and
use as an initial RAM disk (initrd)."
#
# $INITRD_IMAGE_LIVE
# set? /opt/thudPoky/meta/classes/image-live.bbclass:39
# "${MLPREFIX}core-image-minimal-initramfs"
INITRD_IMAGE_LIVE="core-image-minimal-initramfs"
#
# $INITRD_LIVE [2 operations]
# _prepend /opt/thudPoky/meta-intel/conf/machine/include/meta-intel.inc:23
# "${@bb.utils.contains('MACHINE_FEATURES', 'intel-ucode',
'${DEPLOY_DIR_IMAGE}/microcode.cpio ', '', d)}"
# set? /opt/thudPoky/meta/classes/image-live.bbclass:40
# "${DEPLOY_DIR_IMAGE}/${INITRD_IMAGE_LIVE}-${MACHINE}.cpio.gz"
# pre-expansion value:
# "${@bb.utils.contains('MACHINE_FEATURES', 'intel-ucode',
'${DEPLOY_DIR_IMAGE}/microcode.cpio ', '',
d)}${DEPLOY_DIR_IMAGE}/${INITRD_IMAGE_LIVE}-${MACHINE}.cpio.gz"
INITRD_LIVE="/opt/thudPoky/build/tmp/deploy/images/ccns5/microcode.cpio
/opt/thudPoky/build/tmp/deploy/images/ccns5/core-image-minimal-initramfs-ccns5.cpio.gz"The last line seems strange to me because 2 different images are set. .cpio on it's own is not included in INITRAMFS_FSTYPES and I can not find any documentation on the variable INITRD_LIVE.
Best regards
Moritz
Quoted 138 lines · Moritz Porst
Hello Zoran,
thanks for your answerQuoted 21 lines · Zoran Stojsavljevic
Quoted 2 lines
INITRAMFS_IMAGE= /*"core-image-minimal-initramfs"*/INITRAMFS_IMAGE_BUNDLE= "1"...
Quoted 1 line
You can find the
/var/log/dmesghere: https://pastebin.com/ya7iCtq7ISome hints...
[1] Kernel command line: BOOT_IMAGE=/bzImage root=PARTUUID=71d1d94a-83e8-4895-98eb-35309f58119f break=premount quiet rootwait rootwait rootfstype=ext4 /*console=ttyS0,115200 console=tty0*/
/*
*/
input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input7
fbcon: inteldrmfb (fb0) is primary device
Console: switching to colour frame buffer device 128x48 /*i915 0000:00:02.0: fb0: inteldrmfb frame buffer device*/snd_hda_intel0000:00:1b.0: bound 0000:00:02.0 (opsi915_audio_component_bind_ops[i915])Quoted 2 lines
Hmmmmm... You are using console and serial, but full i915 GFX kernel driver is still included in the build???
I started from the core-image-minimal to have a small image and extended it with the features I need, which is e.g. a graphical system. The console=[...] part in the kernel command line is probably a remnant but my image boots into the GUI. Is this a problem ?
Quoted 5 lines
/*
*/
[2] efi: EFI v2.31 by American MegatrendsUsing AMI BIOS as boot loader FW... OK?! Am I correct?
My bootloader is currently grub, the EFI is AM.
Quoted 6 lines
[3] smpboot: CPU0: Intel(R) Atom(TM) CPU E3825 @ 1.33GHz (family:
0x6, model:0x37, stepping:0x9)This is CPUID ID
0x30679, which uses MCU... Which MicroCodeUnit? M0130679xxx (info from AMI BIOS)?Sorry but I can't find this info in the EFI
Quoted 5 lines
[4] Using INTEL ATOM BYT E3825 dual core (sans Hyper-threading), implies that you are using
4GB (e820 messages) as single channel (one memory module DDR3 as 4GB)! Am I correct (important)?2GB, single channel.
Quoted 9 lines
[5] Dracut phase?!
Quoted 2 lines
To my understanding the initramfs should be embedded in
/boot/bzImage. However since I use an intel platform I also have a
/boot/microcode.cpioQuoted 3 lines
which gets loaded via "initrd /microcode.cpio". Removing this line in grub does not enable me to get an initramfs prompt either (again, using break as option).
Quoted 6 lines
You are obviously stopping in boot phase called dracut. Please, try to mount by hand
/dev/sda(whatever)... You should use fdisk -l command, or do ls -al /dev | grep sda to
dig out which partition you need to mount to /tmp dir to see rootfstype=ext4 (HDD/SSD)No, the boot does not stop. Even if I do issue "break=premount" I end up in my graphical interface with the rootfs mounted. This is the last message in the log:
EXT4-fs (sdb2): re-mounted. Opts: (null)
The rootfs partition is always 2, so either/dev/sda2or/dev/sdb2(when booting from stick)Quoted 65 lines
_______
Just thinking loud... .. .
Hope this helps (has very little to do with YOCTO build system, BTW) . ;-)
Zoran
_______On Fri, Jun 28, 2019 at 11:22 AM Moritz Porst <[email protected] <mailto:[email protected]>> wrote:
Hello,
I currently try to deploy a single rootfs update mechanism for my embedded device. I can't boot to initramfs using either "break" or "break=premount" (without quotes...). I tried this in systemd-boot and
grub-efi (always efi boot) but the boot process just continues normally.
If I insert at the same point e.g. "quiet" this argument is recognised.
I boot the .wic image with a separate boot partition from a USB stick.
in local.conf I have set:
INITRAMFS_IMAGE= "core-image-minimal-initramfs"INITRAMFS_IMAGE_BUNDLE= "1"In order to reduce complexity I now use the standard core-image-minimal-initramfs without .bbappend. I can confirm (from seeing the task) that bitbake bundled the kernel with the initramfs.
You can find the
/var/log/dmesghere: https://pastebin.com/ya7iCtq7To my understanding the initramfs should be embedded in
/boot/bzImage.
However since I use an intel platform I also have a/boot/microcode.cpio
which gets loaded via "initrd /microcode.cpio". Removing this line in grub does not enable me to get an initramfs prompt either (again, using
break as option).Did I forget some configuration or do I have to put the break statement
at a very specific position within the "linux ..." boot command ? Do you
know which bitbake variables to check ? (both set in local.conf do not
get overwritten, already checked this). I got the thud branch checked out in all my meta-layers except for meta-qt which is currently on master branch.Help is much appreciated !
Best regards
Moritz--
_______________________________________________
yocto mailing list
[email protected] <mailto:[email protected]>
https://lists.yoctoproject.org/listinfo/yocto
Hello Moritz,
Too hot here, in Belgrade... Where I am resting for the Time being (actually, this message given to my invisible spying security "angels" on this list)... :-) Projected +38C degrees today. Too hot for this too old Siberian untouchable bobcat!
Quoted 4 lines
I started from the core-image-minimal to have a small image and extended it with the features I need, which is e.g. a graphical system. The console=[...] part in the kernel command line is probably a remnant but my image boots into the GUI. Is this a problem ?
Nope, it is not. If you need to do it correctly, you should use bitbake -k core-image-sato build command (my best educated guess). Then, I do not feel comfortable seeing in your kernel command line serial interface, do you agree? YOCTO maintainers, any additional advices?
Quoted 1 line
My bootloader is currently grub, the EFI is AM.
Nope. Eeeeeeeeek. Wrong. Currently, your boot-loader is UEFI AMI. Your OS (Linux probably, U name it) boot-loader is GRUB2. Let us keep it contained, sane and sober.
Quoted 1 line
Sorry but I can't find this info in the EFI.
Could you, please try the following command being root: dmesg | grep MCU. or grep mcu, or grep CPUID or grep cpuid?? Please, post results to this list (to me).
Could you, also, send to YOCTO list/me attached file:/boot/microcode.cpio so I can somehow (?) inspect it? ;-)
Quoted 1 line
2GB, single channel.
All Cool. E3825 by HW/silicon design could/does NOT support multiple memory channels. ONLY single... But even YOCTO primes (INTEL ones from this list) are not gonna tell this to you. Not 'cause they are nasty. They are NOT aware/they are ignorant (with the purpose)! ;-))
Quoted 5 lines
No, the boot does not stop. Even if I do issue "break=premount" I end up in my graphical interface with the rootfs mounted. This is the last message in the log: EXT4-fs (sdb2): re-mounted. Opts: (null) The rootfs partition is always 2, so either
/dev/sda2or/dev/sdb2(when booting from stick)
Yes, from https://pastebin.com/ya7iCtq7, so it is remounted rw, not read only. So, it seems that you have passed dracut phase. and mounted SD or flash rootfs. So, initramfs is NOT your true problem, is it???
Zoran
_______
Quoted 4 lines
No, the boot does not stop. Even if I do issue "break=premount" I end up in my graphical interface with the rootfs mounted. This is the last message in the log: EXT4-fs (sdb2): re-mounted. Opts: (null) The rootfs partition is always 2, so either
/dev/sda2or/dev/sdb2(when booting from stick)
Quoted 114 lines · Moritz Porst
Hello Zoran,
thanks for your answerQuoted 2 lines · Zoran Stojsavljevic
INITRAMFS_IMAGE= "core-image-minimal-initramfs"INITRAMFS_IMAGE_BUNDLE= "1"...
Quoted 1 line
You can find the
/var/log/dmesghere: https://pastebin.com/ya7iCtq7ISome hints...
[1] Kernel command line: BOOT_IMAGE=/bzImage root=PARTUUID=71d1d94a-83e8-4895-98eb-35309f58119f break=premount quiet rootwait rootwait rootfstype=ext4 console=ttyS0,115200 console=tty0
input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input7
fbcon: inteldrmfb (fb0) is primary device
Console: switching to colour frame buffer device 128x48
i915 0000:00:02.0: fb0: inteldrmfb frame buffer devicesnd_hda_intel0000:00:1b.0: bound 0000:00:02.0 (opsi915_audio_component_bind_ops[i915])Hmmmmm... You are using console and serial, but full i915 GFX kernel driver is still included in the build???
I started from the core-image-minimal to have a small image and extended it with the features I need, which is e.g. a graphical system. The console=[...] part in the kernel command line is probably a remnant but my image boots into the GUI. Is this a problem ?
[2] efi: EFI v2.31 by American Megatrends
Using AMI BIOS as boot loader FW... OK?! Am I correct?
My bootloader is currently grub, the EFI is AM.
[3] smpboot: CPU0: Intel(R) Atom(TM) CPU E3825 @ 1.33GHz (family:
0x6, model:0x37, stepping:0x9)This is CPUID ID
0x30679, which uses MCU... Which MicroCodeUnit? M0130679xxx (info from AMI BIOS)?Sorry but I can't find this info in the EFI
[4] Using INTEL ATOM BYT E3825 dual core (sans Hyper-threading), implies that you are using 4GB (e820 messages) as single channel (one memory module DDR3 as 4GB)! Am I correct (important)?
2GB, single channel.
[5] Dracut phase?!
Quoted 5 lines
To my understanding the initramfs should be embedded in
/boot/bzImage. However since I use an intel platform I also have a/boot/microcode.cpiowhich gets loaded via "initrd /microcode.cpio". Removing this line in grub does not enable me to get an initramfs prompt either (again, using break as option).You are obviously stopping in boot phase called dracut. Please, try to mount by hand /dev/sda(whatever)... You should use fdisk -l command, or do ls -al /dev | grep sda to dig out which partition you need to mount to /tmp dir to see rootfstype=ext4 (HDD/SSD)
No, the boot does not stop. Even if I do issue "break=premount" I end up in my graphical interface with the rootfs mounted. This is the last message in the log:
EXT4-fs (sdb2): re-mounted. Opts: (null)
The rootfs partition is always 2, so either/dev/sda2or/dev/sdb2(when booting from stick)_______
Just thinking loud... .. .
Hope this helps (has very little to do with YOCTO build system, BTW) . ;-)
Zoran
_______Quoted 41 lines · Moritz Porst
Hello,
I currently try to deploy a single rootfs update mechanism for my embedded device. I can't boot to initramfs using either "break" or "break=premount" (without quotes...). I tried this in systemd-boot and grub-efi (always efi boot) but the boot process just continues normally. If I insert at the same point e.g. "quiet" this argument is recognised. I boot the .wic image with a separate boot partition from a USB stick. in local.conf I have set:INITRAMFS_IMAGE= "core-image-minimal-initramfs"INITRAMFS_IMAGE_BUNDLE= "1"In order to reduce complexity I now use the standard core-image-minimal-initramfs without .bbappend. I can confirm (from seeing the task) that bitbake bundled the kernel with the initramfs.
You can find the
/var/log/dmesghere: https://pastebin.com/ya7iCtq7To my understanding the initramfs should be embedded in
/boot/bzImage. However since I use an intel platform I also have a/boot/microcode.cpiowhich gets loaded via "initrd /microcode.cpio". Removing this line in grub does not enable me to get an initramfs prompt either (again, using break as option).Did I forget some configuration or do I have to put the break statement at a very specific position within the "linux ..." boot command ? Do you know which bitbake variables to check ? (both set in local.conf do not get overwritten, already checked this). I got the thud branch checked out in all my meta-layers except for meta-qt which is currently on master branch.
Help is much appreciated !
Best regards
Moritz--
_______________________________________________
yocto mailing list
[email protected]
https://lists.yoctoproject.org/listinfo/yocto
Hello,
I think I found the issue. ( see below )
Quoted 6 lines · Zoran Stojsavljevic
Hello Moritz,
Too hot here, in Belgrade... Where I am resting for the Time being (actually, this message given to my invisible spying security "angels" on this list)... :-) Projected +38C degrees today. Too hot for this too old Siberian untouchable bobcat!
Luckily it's a rather cold day in germany, thanks that you still take the time to answer !
Quoted 9 lines
Quoted 5 lines
I started from the core-image-minimal to have a small image and extended it with the features I need, which is e.g. a graphical system. The console=[...] part in the kernel command line is probably a remnant but my image boots into the GUI. Is this a problem ?
Nope, it is not. If you need to do it correctly, you should use bitbake -k core-image-sato build command (my best educated guess). Then, I do not feel comfortable seeing in your kernel command line serial interface, do you agree?
Yes that is true.
Quoted 4 lines
YOCTO maintainers, any additional
advices?Quoted 1 line
My bootloader is currently grub, the EFI is AM.
Quoted 8 lines
Nope. Eeeeeeeeek. Wrong. Currently, your boot-loader is UEFI AMI. Your OS (Linux probably, U name it) boot-loader is GRUB2. Let us keep it contained, sane and sober.
Quoted 1 line
Sorry but I can't find this info in the EFI.
Could you, please try the following command being root: dmesg | grep MCU. or grep mcu, or grep CPUID or grep cpuid?? Please, post results to this list (to me).
No luck unfortunately (used grep -i)
Quoted 3 lines
Could you, also, send to YOCTO list/me attached file:
/boot/microcode.cpioso I can somehow (?) inspect it? ;-)
I send it to you directly, so I don't spam the list with a large attachment.
Quoted 7 lines
Quoted 2 lines
2GB, single channel.
All Cool. E3825 by HW/silicon design could/does NOT support multiple memory channels. ONLY single... But even YOCTO primes (INTEL ones from this list) are not gonna tell this to you. Not 'cause they are nasty. They are NOT aware/they are ignorant (with the purpose)! ;-))
Quoted 8 lines
Quoted 5 lines
No, the boot does not stop. Even if I do issue "break=premount" I end up in my graphical interface with the rootfs mounted. This is the last message in the log: EXT4-fs (sdb2): re-mounted. Opts: (null) The rootfs partition is always 2, so either
/dev/sda2or/dev/sdb2(when booting from stick)Yes, from https://pastebin.com/ya7iCtq7, so it is remounted rw, not read only. So, it seems that you have passed dracut phase. and mounted SD or flash rootfs. So, initramfs is NOT your true problem, is it???
The thing is that the boot works but I want an initramfs that can be used for updating (in case the rootfs is broken). However I need to be able to intercept the boot process there because otherwise I can't deploy an update mechanism, that's what I was trying.
Quoted 11 lines
Zoran
_______Quoted 4 lines
No, the boot does not stop. Even if I do issue "break=premount" I end up in my graphical interface with the rootfs mounted. This is the last message in the log: EXT4-fs (sdb2): re-mounted. Opts: (null) The rootfs partition is always 2, so either
/dev/sda2or/dev/sdb2(when booting from stick)
So for the issue...
I expected yocto to put the bundled bzImage onto my rootfs. This was not the case. My image directory contains 2x bzImage, one bundled and one unbundled. Apparently yocto puts the >un<bundled image onto my /boot partition and uses it for boot. So of course I couldn't access initramfs in this case. Now I get to the initramfs statement "dropping to shell" if I intentionally boot with wrong rootfs.
Still I don't get the interactive shell.
On the github ostroproject site I found this:
# debug: adds debug boot parameters like 'shell' and 'debug', see # meta/recipes-core/initrdscripts/initramfs-framework/debug for details
# Could be removed in more minimal product image. PACKAGE_INSTALL += "initramfs-module-debug"
including the module-debug still does not enable me to get an interactive shell.
I was following this site: https://wiki.debian.org/InitramfsDebug
I am aware that yocto is no debian but I expected that kernel parameters (like 'break') would be independent of the distribution.
Lastly I do not really need the interactive shell, it is enough if I can deploy a custom init script in the initramfs. Still I think that getting an initramfs shell should be as simple as stating the name of the initramfs image and setting the "INITRAMFS_DO_BUNDLE" variable.
Best regards
Moritz
Quoted 111 lines · Moritz Porst
Quoted 110 lines
Hello Zoran,
thanks for your answerQuoted 2 lines · Zoran Stojsavljevic
INITRAMFS_IMAGE= "core-image-minimal-initramfs"INITRAMFS_IMAGE_BUNDLE= "1"...
Quoted 1 line
You can find the
/var/log/dmesghere: https://pastebin.com/ya7iCtq7ISome hints...
[1] Kernel command line: BOOT_IMAGE=/bzImage root=PARTUUID=71d1d94a-83e8-4895-98eb-35309f58119f break=premount quiet rootwait rootwait rootfstype=ext4 console=ttyS0,115200 console=tty0
input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input7
fbcon: inteldrmfb (fb0) is primary device
Console: switching to colour frame buffer device 128x48
i915 0000:00:02.0: fb0: inteldrmfb frame buffer devicesnd_hda_intel0000:00:1b.0: bound 0000:00:02.0 (opsi915_audio_component_bind_ops[i915])Hmmmmm... You are using console and serial, but full i915 GFX kernel driver is still included in the build???
I started from the core-image-minimal to have a small image and extended it with the features I need, which is e.g. a graphical system. The console=[...] part in the kernel command line is probably a remnant but my image boots into the GUI. Is this a problem ?
[2] efi: EFI v2.31 by American Megatrends
Using AMI BIOS as boot loader FW... OK?! Am I correct?
My bootloader is currently grub, the EFI is AM.
[3] smpboot: CPU0: Intel(R) Atom(TM) CPU E3825 @ 1.33GHz (family:
0x6, model:0x37, stepping:0x9)This is CPUID ID
0x30679, which uses MCU... Which MicroCodeUnit? M0130679xxx (info from AMI BIOS)?Sorry but I can't find this info in the EFI
[4] Using INTEL ATOM BYT E3825 dual core (sans Hyper-threading), implies that you are using 4GB (e820 messages) as single channel (one memory module DDR3 as 4GB)! Am I correct (important)?
2GB, single channel.
[5] Dracut phase?!
Quoted 5 lines
To my understanding the initramfs should be embedded in
/boot/bzImage. However since I use an intel platform I also have a/boot/microcode.cpiowhich gets loaded via "initrd /microcode.cpio". Removing this line in grub does not enable me to get an initramfs prompt either (again, using break as option).You are obviously stopping in boot phase called dracut. Please, try to mount by hand /dev/sda(whatever)... You should use fdisk -l command, or do ls -al /dev | grep sda to dig out which partition you need to mount to /tmp dir to see rootfstype=ext4 (HDD/SSD)
No, the boot does not stop. Even if I do issue "break=premount" I end up in my graphical interface with the rootfs mounted. This is the last message in the log:
EXT4-fs (sdb2): re-mounted. Opts: (null)
The rootfs partition is always 2, so either/dev/sda2or/dev/sdb2(when booting from stick)_______
Just thinking loud... .. .
Hope this helps (has very little to do with YOCTO build system, BTW) . ;-)
Zoran
_______Quoted 40 lines · Moritz Porst
Hello,
I currently try to deploy a single rootfs update mechanism for my embedded device. I can't boot to initramfs using either "break" or "break=premount" (without quotes...). I tried this in systemd-boot and grub-efi (always efi boot) but the boot process just continues normally. If I insert at the same point e.g. "quiet" this argument is recognised. I boot the .wic image with a separate boot partition from a USB stick. in local.conf I have set:INITRAMFS_IMAGE= "core-image-minimal-initramfs"INITRAMFS_IMAGE_BUNDLE= "1"In order to reduce complexity I now use the standard core-image-minimal-initramfs without .bbappend. I can confirm (from seeing the task) that bitbake bundled the kernel with the initramfs.
You can find the
/var/log/dmesghere: https://pastebin.com/ya7iCtq7To my understanding the initramfs should be embedded in
/boot/bzImage. However since I use an intel platform I also have a/boot/microcode.cpiowhich gets loaded via "initrd /microcode.cpio". Removing this line in grub does not enable me to get an initramfs prompt either (again, using break as option).Did I forget some configuration or do I have to put the break statement at a very specific position within the "linux ..." boot command ? Do you know which bitbake variables to check ? (both set in local.conf do not get overwritten, already checked this). I got the thud branch checked out in all my meta-layers except for meta-qt which is currently on master branch.
Help is much appreciated !
Best regards
Moritz--
_______________________________________________
yocto mailing list
[email protected]
https://lists.yoctoproject.org/listinfo/yocto
Hello Moritz,
I need here some help from you. I'll try to reconstruct the parts of the local.conf you are using, so I (and Jupiter) can understand what should we do to also bundle kernel image with initramfs, to end up in Dracut/rescue shell.
Here is what I anticipate after reading several YOCTO @ threads:
IMAGE_FSTYPES_append = " cpio.gz"INITRAMFS_IMAGE = "core-image-minimal-initramfs" INITRAMFS_IMAGE_BUNDLE = "1"
# debug: adds debug boot parameters like 'shell' and 'debug', see
# meta/recipes-core/initrdscripts/initramfs-framework/debug for details # Could be removed in more minimal product image PACKAGE_INSTALL += "initramfs-module-debug"
Could you, please, review these lines and fix, if something is not correct?
I what I understood, this does the magic, but you could not stop in initramfs shell? Still, this problem is not solved?
Quoted 9 lines
I was following this site: https://wiki.debian.org/InitramfsDebug
Rescue shell (also known as initramfs shell)
Read man initramfs-tools to learn about the break=something kernel parameter (where valid arguments for something are: top, modules, premount, mount, mountroot, bottom, init), which starts a debug shell. You can try, for example, break=premount. You can edit/boot/grub/grub.cfgto add this to the end of the kernel line, or you can do it interactively from the grub boot menu: "e" to edit, and "b" to boot once you've edited the kernel line.
Now, as my understanding is, you solved this problem actually adding to grub.cfg in command kernel line break=premount, and was able to stop in rescue shell?! Am I correct here?
Thank you,
Zoran
_______
Quoted 216 lines · Moritz Porst
Hello,
I think I found the issue. ( see below )On 01.07.19 15:57, Zoran Stojsavljevic wrote:
Hello Moritz,
Too hot here, in Belgrade... Where I am resting for the Time being (actually, this message given to my invisible spying security "angels" on this list)... :-) Projected +38C degrees today. Too hot for this too old Siberian untouchable bobcat!
Luckily it's a rather cold day in germany, thanks that you still take the time to answer !
I started from the core-image-minimal to have a small image and extended it with the features I need, which is e.g. a graphical system. The console=[...] part in the kernel command line is probably a remnant but my image boots into the GUI. Is this a problem ?
Nope, it is not. If you need to do it correctly, you should use bitbake -k core-image-sato build command (my best educated guess). Then, I do not feel comfortable seeing in your kernel command line serial interface, do you agree?
Yes that is true.
YOCTO maintainers, any additional
advices?My bootloader is currently grub, the EFI is AM.
Nope. Eeeeeeeeek. Wrong. Currently, your boot-loader is UEFI AMI. Your OS (Linux probably, U name it) boot-loader is GRUB2. Let us keep it contained, sane and sober.
Sorry but I can't find this info in the EFI.
Could you, please try the following command being root: dmesg | grep MCU. or grep mcu, or grep CPUID or grep cpuid?? Please, post results to this list (to me).
No luck unfortunately (used grep -i)
Could you, also, send to YOCTO list/me attached file:
/boot/microcode.cpioso I can somehow (?) inspect it? ;-)I send it to you directly, so I don't spam the list with a large attachment.
2GB, single channel.
All Cool. E3825 by HW/silicon design could/does NOT support multiple memory channels. ONLY single... But even YOCTO primes (INTEL ones from this list) are not gonna tell this to you. Not 'cause they are nasty. They are NOT aware/they are ignorant (with the purpose)! ;-))
No, the boot does not stop. Even if I do issue "break=premount" I end up in my graphical interface with the rootfs mounted. This is the last message in the log: EXT4-fs (sdb2): re-mounted. Opts: (null) The rootfs partition is always 2, so either
/dev/sda2or/dev/sdb2(when booting from stick)Yes, from https://pastebin.com/ya7iCtq7, so it is remounted rw, not read only. So, it seems that you have passed dracut phase. and mounted SD or flash rootfs. So, initramfs is NOT your true problem, is it???
The thing is that the boot works but I want an initramfs that can be used for updating (in case the rootfs is broken). However I need to be able to intercept the boot process there because otherwise I can't deploy an update mechanism, that's what I was trying.
Zoran
_______No, the boot does not stop. Even if I do issue "break=premount" I end up in my graphical interface with the rootfs mounted. This is the last message in the log: EXT4-fs (sdb2): re-mounted. Opts: (null) The rootfs partition is always 2, so either
/dev/sda2or/dev/sdb2(when booting from stick)So for the issue...
I expected yocto to put the bundled bzImage onto my rootfs. This was not the case. My image directory contains 2x bzImage, one bundled and one unbundled. Apparently yocto puts the >un<bundled image onto my /boot partition and uses it for boot. So of course I couldn't access initramfs in this case. Now I get to the initramfs statement "dropping to shell" if I intentionally boot with wrong rootfs. Still I don't get the interactive shell.
On the github ostroproject site I found this:# debug: adds debug boot parameters like 'shell' and 'debug', see
# meta/recipes-core/initrdscripts/initramfs-framework/debug for details
# Could be removed in more minimal product image.PACKAGE_INSTALL+= "initramfs-module-debug"including the module-debug still does not enable me to get an interactive shell.
I was following this site: https://wiki.debian.org/InitramfsDebug
I am aware that yocto is no debian but I expected that kernel parameters (like 'break') would be independent of the distribution.Lastly I do not really need the interactive shell, it is enough if I can deploy a custom init script in the initramfs. Still I think that getting an initramfs shell should be as simple as stating the name of the initramfs image and setting the "
INITRAMFS_DO_BUNDLE" variable.Best regards
MoritzOn Mon, Jul 1, 2019 at 11:20 AM Moritz Porst <[email protected]> wrote:
Hello Zoran,
thanks for your answerOn 28.06.19 14:26, Zoran Stojsavljevic wrote:
INITRAMFS_IMAGE= "core-image-minimal-initramfs"INITRAMFS_IMAGE_BUNDLE= "1"...
You can find the
/var/log/dmesghere: https://pastebin.com/ya7iCtq7ISome hints...
[1] Kernel command line: BOOT_IMAGE=/bzImage root=PARTUUID=71d1d94a-83e8-4895-98eb-35309f58119f break=premount quiet rootwait rootwait rootfstype=ext4 console=ttyS0,115200 console=tty0
input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input7
fbcon: inteldrmfb (fb0) is primary device
Console: switching to colour frame buffer device 128x48
i915 0000:00:02.0: fb0: inteldrmfb frame buffer devicesnd_hda_intel0000:00:1b.0: bound 0000:00:02.0 (opsi915_audio_component_bind_ops[i915])Hmmmmm... You are using console and serial, but full i915 GFX kernel driver is still included in the build???
I started from the core-image-minimal to have a small image and extended it with the features I need, which is e.g. a graphical system. The console=[...] part in the kernel command line is probably a remnant but my image boots into the GUI. Is this a problem ?
[2] efi: EFI v2.31 by American Megatrends
Using AMI BIOS as boot loader FW... OK?! Am I correct?
My bootloader is currently grub, the EFI is AM.
[3] smpboot: CPU0: Intel(R) Atom(TM) CPU E3825 @ 1.33GHz (family:
0x6, model:0x37, stepping:0x9)This is CPUID ID
0x30679, which uses MCU... Which MicroCodeUnit? M0130679xxx (info from AMI BIOS)?Sorry but I can't find this info in the EFI
[4] Using INTEL ATOM BYT E3825 dual core (sans Hyper-threading), implies that you are using 4GB (e820 messages) as single channel (one memory module DDR3 as 4GB)! Am I correct (important)?
2GB, single channel.
[5] Dracut phase?!
To my understanding the initramfs should be embedded in
/boot/bzImage. However since I use an intel platform I also have a/boot/microcode.cpiowhich gets loaded via "initrd /microcode.cpio". Removing this line in grub does not enable me to get an initramfs prompt either (again, using break as option).You are obviously stopping in boot phase called dracut. Please, try to mount by hand /dev/sda(whatever)... You should use fdisk -l command, or do ls -al /dev | grep sda to dig out which partition you need to mount to /tmp dir to see rootfstype=ext4 (HDD/SSD)
No, the boot does not stop. Even if I do issue "break=premount" I end up in my graphical interface with the rootfs mounted. This is the last message in the log:
EXT4-fs (sdb2): re-mounted. Opts: (null)
The rootfs partition is always 2, so either/dev/sda2or/dev/sdb2(when booting from stick)_______
Just thinking loud... .. .
Hope this helps (has very little to do with YOCTO build system, BTW) . ;-)
Zoran
_______On Fri, Jun 28, 2019 at 11:22 AM Moritz Porst <[email protected]> wrote:
Hello,
I currently try to deploy a single rootfs update mechanism for my embedded device. I can't boot to initramfs using either "break" or "break=premount" (without quotes...). I tried this in systemd-boot and grub-efi (always efi boot) but the boot process just continues normally. If I insert at the same point e.g. "quiet" this argument is recognised. I boot the .wic image with a separate boot partition from a USB stick. in local.conf I have set:INITRAMFS_IMAGE= "core-image-minimal-initramfs"INITRAMFS_IMAGE_BUNDLE= "1"In order to reduce complexity I now use the standard core-image-minimal-initramfs without .bbappend. I can confirm (from seeing the task) that bitbake bundled the kernel with the initramfs.
You can find the
/var/log/dmesghere: https://pastebin.com/ya7iCtq7To my understanding the initramfs should be embedded in
/boot/bzImage. However since I use an intel platform I also have a/boot/microcode.cpiowhich gets loaded via "initrd /microcode.cpio". Removing this line in grub does not enable me to get an initramfs prompt either (again, using break as option).Did I forget some configuration or do I have to put the break statement at a very specific position within the "linux ..." boot command ? Do you know which bitbake variables to check ? (both set in local.conf do not get overwritten, already checked this). I got the thud branch checked out in all my meta-layers except for meta-qt which is currently on master branch.
Help is much appreciated !
Best regards
Moritz--
_______________________________________________
yocto mailing list
[email protected]
https://lists.yoctoproject.org/listinfo/yocto
Hello Zoran, Jupiter and list
The configuration you sent seems to be correct.
As I already said initramfs seems overly complicated in yocto. the most important thing to note is that 2 kernel images are created, one is called bzImage (in my case) an the other bzImage-initramfs. However only the bzImage is written into the rootfs so you have to exchange them manually. (in /boot/bzImage). I did not find a way of including the bundled kernel right away.
What you can do is to build core-image-minimal-initramfs and delete the symbolic link "bzImage", then recreate it and let it point to bzImage-initramfs. However this is rather a hack than a solution.
An other mistake I made was to use IMAGE_INSTALL_append which is ignored. Use PACKAGE_INSTALL_append.
Also I found that "break" does not work as a kernel parameter. Use "shell" oder "debug-shell" instead. If you want to try to boot into initramfs you can remove all parameters to the booting line so you either end up in a kernel panic (initramfs doesn't work) or in the rescue shell (initramfs works).
In the end I actually managed to get a working shell, but I often ended up in initramfs telling me "dropping to shell..." but then freezing.
I don't have access to my files right now but I can tell you more on my setup tomorrow. In case the solution is not included above.
Best regards
Moritz
Quoted 256 lines · Zoran Stojsavljevic
Hello Moritz,
I need here some help from you. I'll try to reconstruct the parts of the local.conf you are using, so I (and Jupiter) can understand what should we do to also bundle kernel image with initramfs, to end up in Dracut/rescue shell.
Here is what I anticipate after reading several YOCTO @ threads:
IMAGE_FSTYPES_append= " cpio.gz"INITRAMFS_IMAGE= "core-image-minimal-initramfs"INITRAMFS_IMAGE_BUNDLE= "1"
# debug: adds debug boot parameters like 'shell' and 'debug', see# meta/recipes-core/initrdscripts/initramfs-framework/debug for details # Could be removed in more minimal product image PACKAGE_INSTALL += "initramfs-module-debug"Could you, please, review these lines and fix, if something is not correct?
I what I understood, this does the magic, but you could not stop in initramfs shell? Still, this problem is not solved?
Quoted 9 lines
I was following this site: https://wiki.debian.org/InitramfsDebug
Rescue shell (also known as initramfs shell)
Read man initramfs-tools to learn about the break=something kernel parameter (where valid arguments for something are: top, modules, premount, mount, mountroot, bottom, init), which starts a debug shell. You can try, for example, break=premount. You can edit/boot/grub/grub.cfgto add this to the end of the kernel line, or you can do it interactively from the grub boot menu: "e" to edit, and "b" to boot once you've edited the kernel line.Now, as my understanding is, you solved this problem actually adding to grub.cfg in command kernel line break=premount, and was able to stop in rescue shell?! Am I correct here?
Thank you,
Zoran
_______Quoted 215 lines · Moritz Porst
Hello,
I think I found the issue. ( see below )On 01.07.19 15:57, Zoran Stojsavljevic wrote:
Hello Moritz,
Too hot here, in Belgrade... Where I am resting for the Time being (actually, this message given to my invisible spying security "angels" on this list)... :-) Projected +38C degrees today. Too hot for this too old Siberian untouchable bobcat!
Luckily it's a rather cold day in germany, thanks that you still take the time to answer !
I started from the core-image-minimal to have a small image and extended it with the features I need, which is e.g. a graphical system. The console=[...] part in the kernel command line is probably a remnant but my image boots into the GUI. Is this a problem ?
Nope, it is not. If you need to do it correctly, you should use bitbake -k core-image-sato build command (my best educated guess). Then, I do not feel comfortable seeing in your kernel command line serial interface, do you agree?
Yes that is true.
YOCTO maintainers, any additional
advices?My bootloader is currently grub, the EFI is AM.
Nope. Eeeeeeeeek. Wrong. Currently, your boot-loader is UEFI AMI. Your OS (Linux probably, U name it) boot-loader is GRUB2. Let us keep it contained, sane and sober.
Sorry but I can't find this info in the EFI.
Could you, please try the following command being root: dmesg | grep MCU. or grep mcu, or grep CPUID or grep cpuid?? Please, post results to this list (to me).
No luck unfortunately (used grep -i)
Could you, also, send to YOCTO list/me attached file:
/boot/microcode.cpioso I can somehow (?) inspect it? ;-)I send it to you directly, so I don't spam the list with a large attachment.
2GB, single channel.
All Cool. E3825 by HW/silicon design could/does NOT support multiple memory channels. ONLY single... But even YOCTO primes (INTEL ones from this list) are not gonna tell this to you. Not 'cause they are nasty. They are NOT aware/they are ignorant (with the purpose)! ;-))
No, the boot does not stop. Even if I do issue "break=premount" I end up in my graphical interface with the rootfs mounted. This is the last message in the log: EXT4-fs (sdb2): re-mounted. Opts: (null) The rootfs partition is always 2, so either
/dev/sda2or/dev/sdb2(when booting from stick)Yes, from https://pastebin.com/ya7iCtq7, so it is remounted rw, not read only. So, it seems that you have passed dracut phase. and mounted SD or flash rootfs. So, initramfs is NOT your true problem, is it???
The thing is that the boot works but I want an initramfs that can be used for updating (in case the rootfs is broken). However I need to be able to intercept the boot process there because otherwise I can't deploy an update mechanism, that's what I was trying.
Zoran
_______No, the boot does not stop. Even if I do issue "break=premount" I end up in my graphical interface with the rootfs mounted. This is the last message in the log: EXT4-fs (sdb2): re-mounted. Opts: (null) The rootfs partition is always 2, so either
/dev/sda2or/dev/sdb2(when booting from stick)So for the issue...
I expected yocto to put the bundled bzImage onto my rootfs. This was not the case. My image directory contains 2x bzImage, one bundled and one unbundled. Apparently yocto puts the >un<bundled image onto my /boot partition and uses it for boot. So of course I couldn't access initramfs in this case. Now I get to the initramfs statement "dropping to shell" if I intentionally boot with wrong rootfs. Still I don't get the interactive shell.
On the github ostroproject site I found this:# debug: adds debug boot parameters like 'shell' and 'debug', see
# meta/recipes-core/initrdscripts/initramfs-framework/debug for details
# Could be removed in more minimal product image.PACKAGE_INSTALL+= "initramfs-module-debug"including the module-debug still does not enable me to get an interactive shell.
I was following this site: https://wiki.debian.org/InitramfsDebug
I am aware that yocto is no debian but I expected that kernel parameters (like 'break') would be independent of the distribution.Lastly I do not really need the interactive shell, it is enough if I can deploy a custom init script in the initramfs. Still I think that getting an initramfs shell should be as simple as stating the name of the initramfs image and setting the "
INITRAMFS_DO_BUNDLE" variable.Best regards
MoritzOn Mon, Jul 1, 2019 at 11:20 AM Moritz Porst <[email protected]> wrote:
Hello Zoran,
thanks for your answerOn 28.06.19 14:26, Zoran Stojsavljevic wrote:
INITRAMFS_IMAGE= "core-image-minimal-initramfs"INITRAMFS_IMAGE_BUNDLE= "1"...
You can find the
/var/log/dmesghere: https://pastebin.com/ya7iCtq7ISome hints...
[1] Kernel command line: BOOT_IMAGE=/bzImage root=PARTUUID=71d1d94a-83e8-4895-98eb-35309f58119f break=premount quiet rootwait rootwait rootfstype=ext4 console=ttyS0,115200 console=tty0
input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input7
fbcon: inteldrmfb (fb0) is primary device
Console: switching to colour frame buffer device 128x48
i915 0000:00:02.0: fb0: inteldrmfb frame buffer devicesnd_hda_intel0000:00:1b.0: bound 0000:00:02.0 (opsi915_audio_component_bind_ops[i915])Hmmmmm... You are using console and serial, but full i915 GFX kernel driver is still included in the build???
I started from the core-image-minimal to have a small image and extended it with the features I need, which is e.g. a graphical system. The console=[...] part in the kernel command line is probably a remnant but my image boots into the GUI. Is this a problem ?
[2] efi: EFI v2.31 by American Megatrends
Using AMI BIOS as boot loader FW... OK?! Am I correct?
My bootloader is currently grub, the EFI is AM.
[3] smpboot: CPU0: Intel(R) Atom(TM) CPU E3825 @ 1.33GHz (family:
0x6, model:0x37, stepping:0x9)This is CPUID ID
0x30679, which uses MCU... Which MicroCodeUnit? M0130679xxx (info from AMI BIOS)?Sorry but I can't find this info in the EFI
[4] Using INTEL ATOM BYT E3825 dual core (sans Hyper-threading), implies that you are using 4GB (e820 messages) as single channel (one memory module DDR3 as 4GB)! Am I correct (important)?
2GB, single channel.
[5] Dracut phase?!
To my understanding the initramfs should be embedded in
/boot/bzImage. However since I use an intel platform I also have a/boot/microcode.cpiowhich gets loaded via "initrd /microcode.cpio". Removing this line in grub does not enable me to get an initramfs prompt either (again, using break as option).You are obviously stopping in boot phase called dracut. Please, try to mount by hand /dev/sda(whatever)... You should use fdisk -l command, or do ls -al /dev | grep sda to dig out which partition you need to mount to /tmp dir to see rootfstype=ext4 (HDD/SSD)
No, the boot does not stop. Even if I do issue "break=premount" I end up in my graphical interface with the rootfs mounted. This is the last message in the log:
EXT4-fs (sdb2): re-mounted. Opts: (null)
The rootfs partition is always 2, so either/dev/sda2or/dev/sdb2(when booting from stick)_______
Just thinking loud... .. .
Hope this helps (has very little to do with YOCTO build system, BTW) . ;-)
Zoran
_______On Fri, Jun 28, 2019 at 11:22 AM Moritz Porst <[email protected]> wrote:
Hello,
I currently try to deploy a single rootfs update mechanism for my embedded device. I can't boot to initramfs using either "break" or "break=premount" (without quotes...). I tried this in systemd-boot and grub-efi (always efi boot) but the boot process just continues normally. If I insert at the same point e.g. "quiet" this argument is recognised. I boot the .wic image with a separate boot partition from a USB stick. in local.conf I have set:INITRAMFS_IMAGE= "core-image-minimal-initramfs"INITRAMFS_IMAGE_BUNDLE= "1"In order to reduce complexity I now use the standard core-image-minimal-initramfs without .bbappend. I can confirm (from seeing the task) that bitbake bundled the kernel with the initramfs.
You can find the
/var/log/dmesghere: https://pastebin.com/ya7iCtq7To my understanding the initramfs should be embedded in
/boot/bzImage. However since I use an intel platform I also have a/boot/microcode.cpiowhich gets loaded via "initrd /microcode.cpio". Removing this line in grub does not enable me to get an initramfs prompt either (again, using break as option).Did I forget some configuration or do I have to put the break statement at a very specific position within the "linux ..." boot command ? Do you know which bitbake variables to check ? (both set in local.conf do not get overwritten, already checked this). I got the thud branch checked out in all my meta-layers except for meta-qt which is currently on master branch.
Help is much appreciated !
Best regards
Moritz--
_______________________________________________
yocto mailing list
[email protected]
https://lists.yoctoproject.org/listinfo/yocto
Moritz,
Thank you very much for this reply. It makes it very clear... What is the current State of Affairs for the topic.
Let us see if there will be the improvement to this topic. I'll document this on one of my private GitHubs. And archive this email.
Zoran
_______
Quoted 291 lines · Moritz Porst
Hello Zoran, Jupiter and list
The configuration you sent seems to be correct.
As I already said initramfs seems overly complicated in yocto. the most important thing to note is that 2 kernel images are created, one is called bzImage (in my case) an the other bzImage-initramfs. However only the bzImage is written into the rootfs so you have to exchange them manually. (in
/boot/bzImage). I did not find a way of including the bundled kernel right away.What you can do is to build core-image-minimal-initramfs and delete the symbolic link "bzImage", then recreate it and let it point to bzImage-initramfs. However this is rather a hack than a solution.
An other mistake I made was to use
IMAGE_INSTALL_appendwhich is ignored. UsePACKAGE_INSTALL_append.Also I found that "break" does not work as a kernel parameter. Use "shell" oder "debug-shell" instead. If you want to try to boot into initramfs you can remove all parameters to the booting line so you either end up in a kernel panic (initramfs doesn't work) or in the rescue shell (initramfs works).
In the end I actually managed to get a working shell, but I often ended up in initramfs telling me "dropping to shell..." but then freezing.
I don't have access to my files right now but I can tell you more on my setup tomorrow. In case the solution is not included above.
Best regards
MoritzQuoted 256 lines · Zoran Stojsavljevic
Hello Moritz,
I need here some help from you. I'll try to reconstruct the parts of the local.conf you are using, so I (and Jupiter) can understand what should we do to also bundle kernel image with initramfs, to end up in Dracut/rescue shell.
Here is what I anticipate after reading several YOCTO @ threads:
IMAGE_FSTYPES_append= " cpio.gz"INITRAMFS_IMAGE= "core-image-minimal-initramfs"INITRAMFS_IMAGE_BUNDLE= "1"
# debug: adds debug boot parameters like 'shell' and 'debug', see# meta/recipes-core/initrdscripts/initramfs-framework/debug for details # Could be removed in more minimal product image PACKAGE_INSTALL += "initramfs-module-debug"Could you, please, review these lines and fix, if something is not correct?
I what I understood, this does the magic, but you could not stop in initramfs shell? Still, this problem is not solved?
Quoted 9 lines
I was following this site: https://wiki.debian.org/InitramfsDebug
Rescue shell (also known as initramfs shell)
Read man initramfs-tools to learn about the break=something kernel parameter (where valid arguments for something are: top, modules, premount, mount, mountroot, bottom, init), which starts a debug shell. You can try, for example, break=premount. You can edit/boot/grub/grub.cfgto add this to the end of the kernel line, or you can do it interactively from the grub boot menu: "e" to edit, and "b" to boot once you've edited the kernel line.Now, as my understanding is, you solved this problem actually adding to grub.cfg in command kernel line break=premount, and was able to stop in rescue shell?! Am I correct here?
Thank you,
Zoran
_______Quoted 215 lines · Moritz Porst
Hello,
I think I found the issue. ( see below )On 01.07.19 15:57, Zoran Stojsavljevic wrote:
Hello Moritz,
Too hot here, in Belgrade... Where I am resting for the Time being (actually, this message given to my invisible spying security "angels" on this list)... :-) Projected +38C degrees today. Too hot for this too old Siberian untouchable bobcat!
Luckily it's a rather cold day in germany, thanks that you still take the time to answer !
I started from the core-image-minimal to have a small image and extended it with the features I need, which is e.g. a graphical system. The console=[...] part in the kernel command line is probably a remnant but my image boots into the GUI. Is this a problem ?
Nope, it is not. If you need to do it correctly, you should use bitbake -k core-image-sato build command (my best educated guess). Then, I do not feel comfortable seeing in your kernel command line serial interface, do you agree?
Yes that is true.
YOCTO maintainers, any additional
advices?My bootloader is currently grub, the EFI is AM.
Nope. Eeeeeeeeek. Wrong. Currently, your boot-loader is UEFI AMI. Your OS (Linux probably, U name it) boot-loader is GRUB2. Let us keep it contained, sane and sober.
Sorry but I can't find this info in the EFI.
Could you, please try the following command being root: dmesg | grep MCU. or grep mcu, or grep CPUID or grep cpuid?? Please, post results to this list (to me).
No luck unfortunately (used grep -i)
Could you, also, send to YOCTO list/me attached file:
/boot/microcode.cpioso I can somehow (?) inspect it? ;-)I send it to you directly, so I don't spam the list with a large attachment.
2GB, single channel.
All Cool. E3825 by HW/silicon design could/does NOT support multiple memory channels. ONLY single... But even YOCTO primes (INTEL ones from this list) are not gonna tell this to you. Not 'cause they are nasty. They are NOT aware/they are ignorant (with the purpose)! ;-))
No, the boot does not stop. Even if I do issue "break=premount" I end up in my graphical interface with the rootfs mounted. This is the last message in the log: EXT4-fs (sdb2): re-mounted. Opts: (null) The rootfs partition is always 2, so either
/dev/sda2or/dev/sdb2(when booting from stick)Yes, from https://pastebin.com/ya7iCtq7, so it is remounted rw, not read only. So, it seems that you have passed dracut phase. and mounted SD or flash rootfs. So, initramfs is NOT your true problem, is it???
The thing is that the boot works but I want an initramfs that can be used for updating (in case the rootfs is broken). However I need to be able to intercept the boot process there because otherwise I can't deploy an update mechanism, that's what I was trying.
Zoran
_______No, the boot does not stop. Even if I do issue "break=premount" I end up in my graphical interface with the rootfs mounted. This is the last message in the log: EXT4-fs (sdb2): re-mounted. Opts: (null) The rootfs partition is always 2, so either
/dev/sda2or/dev/sdb2(when booting from stick)So for the issue...
I expected yocto to put the bundled bzImage onto my rootfs. This was not the case. My image directory contains 2x bzImage, one bundled and one unbundled. Apparently yocto puts the >un<bundled image onto my /boot partition and uses it for boot. So of course I couldn't access initramfs in this case. Now I get to the initramfs statement "dropping to shell" if I intentionally boot with wrong rootfs. Still I don't get the interactive shell.
On the github ostroproject site I found this:# debug: adds debug boot parameters like 'shell' and 'debug', see
# meta/recipes-core/initrdscripts/initramfs-framework/debug for details
# Could be removed in more minimal product image.PACKAGE_INSTALL+= "initramfs-module-debug"including the module-debug still does not enable me to get an interactive shell.
I was following this site: https://wiki.debian.org/InitramfsDebug
I am aware that yocto is no debian but I expected that kernel parameters (like 'break') would be independent of the distribution.Lastly I do not really need the interactive shell, it is enough if I can deploy a custom init script in the initramfs. Still I think that getting an initramfs shell should be as simple as stating the name of the initramfs image and setting the "
INITRAMFS_DO_BUNDLE" variable.Best regards
MoritzOn Mon, Jul 1, 2019 at 11:20 AM Moritz Porst <[email protected]> wrote:
Hello Zoran,
thanks for your answerOn 28.06.19 14:26, Zoran Stojsavljevic wrote:
INITRAMFS_IMAGE= "core-image-minimal-initramfs"INITRAMFS_IMAGE_BUNDLE= "1"...
You can find the
/var/log/dmesghere: https://pastebin.com/ya7iCtq7ISome hints...
[1] Kernel command line: BOOT_IMAGE=/bzImage root=PARTUUID=71d1d94a-83e8-4895-98eb-35309f58119f break=premount quiet rootwait rootwait rootfstype=ext4 console=ttyS0,115200 console=tty0
input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input7
fbcon: inteldrmfb (fb0) is primary device
Console: switching to colour frame buffer device 128x48
i915 0000:00:02.0: fb0: inteldrmfb frame buffer devicesnd_hda_intel0000:00:1b.0: bound 0000:00:02.0 (opsi915_audio_component_bind_ops[i915])Hmmmmm... You are using console and serial, but full i915 GFX kernel driver is still included in the build???
I started from the core-image-minimal to have a small image and extended it with the features I need, which is e.g. a graphical system. The console=[...] part in the kernel command line is probably a remnant but my image boots into the GUI. Is this a problem ?
[2] efi: EFI v2.31 by American Megatrends
Using AMI BIOS as boot loader FW... OK?! Am I correct?
My bootloader is currently grub, the EFI is AM.
[3] smpboot: CPU0: Intel(R) Atom(TM) CPU E3825 @ 1.33GHz (family:
0x6, model:0x37, stepping:0x9)This is CPUID ID
0x30679, which uses MCU... Which MicroCodeUnit? M0130679xxx (info from AMI BIOS)?Sorry but I can't find this info in the EFI
[4] Using INTEL ATOM BYT E3825 dual core (sans Hyper-threading), implies that you are using 4GB (e820 messages) as single channel (one memory module DDR3 as 4GB)! Am I correct (important)?
2GB, single channel.
[5] Dracut phase?!
To my understanding the initramfs should be embedded in
/boot/bzImage. However since I use an intel platform I also have a/boot/microcode.cpiowhich gets loaded via "initrd /microcode.cpio". Removing this line in grub does not enable me to get an initramfs prompt either (again, using break as option).You are obviously stopping in boot phase called dracut. Please, try to mount by hand /dev/sda(whatever)... You should use fdisk -l command, or do ls -al /dev | grep sda to dig out which partition you need to mount to /tmp dir to see rootfstype=ext4 (HDD/SSD)
No, the boot does not stop. Even if I do issue "break=premount" I end up in my graphical interface with the rootfs mounted. This is the last message in the log:
EXT4-fs (sdb2): re-mounted. Opts: (null)
The rootfs partition is always 2, so either/dev/sda2or/dev/sdb2(when booting from stick)_______
Just thinking loud... .. .
Hope this helps (has very little to do with YOCTO build system, BTW) . ;-)
Zoran
_______On Fri, Jun 28, 2019 at 11:22 AM Moritz Porst <[email protected]> wrote:
Hello,
I currently try to deploy a single rootfs update mechanism for my embedded device. I can't boot to initramfs using either "break" or "break=premount" (without quotes...). I tried this in systemd-boot and grub-efi (always efi boot) but the boot process just continues normally. If I insert at the same point e.g. "quiet" this argument is recognised. I boot the .wic image with a separate boot partition from a USB stick. in local.conf I have set:INITRAMFS_IMAGE= "core-image-minimal-initramfs"INITRAMFS_IMAGE_BUNDLE= "1"In order to reduce complexity I now use the standard core-image-minimal-initramfs without .bbappend. I can confirm (from seeing the task) that bitbake bundled the kernel with the initramfs.
You can find the
/var/log/dmesghere: https://pastebin.com/ya7iCtq7To my understanding the initramfs should be embedded in
/boot/bzImage. However since I use an intel platform I also have a/boot/microcode.cpiowhich gets loaded via "initrd /microcode.cpio". Removing this line in grub does not enable me to get an initramfs prompt either (again, using break as option).Did I forget some configuration or do I have to put the break statement at a very specific position within the "linux ..." boot command ? Do you know which bitbake variables to check ? (both set in local.conf do not get overwritten, already checked this). I got the thud branch checked out in all my meta-layers except for meta-qt which is currently on master branch.
Help is much appreciated !
Best regards
Moritz--
_______________________________________________
yocto mailing list
[email protected]
https://lists.yoctoproject.org/listinfo/yocto
Hey,
The only thing I can add to what I already said is my "core-image-minimal-initramfs.bbappend":PACKAGE_INSTALL += "\
busybox \
base-files \
base-passwd \
bash \
util-linux-lsblk \
vim \
"
Jupiter, are you able to produce your zImage-initramfs now ? If not further do the following:
bitbake <your-image> -e > tempfile
[wait until done, then search]
grep <appropriate search word> tempfile
where <appropriate search word> may be e.g.: zImage, zImage-initramfs, INITRAMFS_IMAGE, INITRAMFS_IMAGE_BUNDLE
Especially check that all variables you set are not overwritten somewhere else
Best regards
Moritz
Quoted 302 lines · Zoran Stojsavljevic
Moritz,
Thank you very much for this reply. It makes it very clear... What is the current State of Affairs for the topic.
Let us see if there will be the improvement to this topic. I'll document this on one of my private GitHubs. And archive this email.
Zoran
_______Quoted 290 lines · Moritz Porst
Hello Zoran, Jupiter and list
The configuration you sent seems to be correct.
As I already said initramfs seems overly complicated in yocto. the most important thing to note is that 2 kernel images are created, one is called bzImage (in my case) an the other bzImage-initramfs. However only the bzImage is written into the rootfs so you have to exchange them manually. (in
/boot/bzImage). I did not find a way of including the bundled kernel right away.What you can do is to build core-image-minimal-initramfs and delete the symbolic link "bzImage", then recreate it and let it point to bzImage-initramfs. However this is rather a hack than a solution.
An other mistake I made was to use
IMAGE_INSTALL_appendwhich is ignored. UsePACKAGE_INSTALL_append.Also I found that "break" does not work as a kernel parameter. Use "shell" oder "debug-shell" instead. If you want to try to boot into initramfs you can remove all parameters to the booting line so you either end up in a kernel panic (initramfs doesn't work) or in the rescue shell (initramfs works).
In the end I actually managed to get a working shell, but I often ended up in initramfs telling me "dropping to shell..." but then freezing.
I don't have access to my files right now but I can tell you more on my setup tomorrow. In case the solution is not included above.
Best regards
MoritzQuoted 256 lines · Zoran Stojsavljevic
Hello Moritz,
I need here some help from you. I'll try to reconstruct the parts of the local.conf you are using, so I (and Jupiter) can understand what should we do to also bundle kernel image with initramfs, to end up in Dracut/rescue shell.
Here is what I anticipate after reading several YOCTO @ threads:
IMAGE_FSTYPES_append= " cpio.gz"INITRAMFS_IMAGE= "core-image-minimal-initramfs"INITRAMFS_IMAGE_BUNDLE= "1"
# debug: adds debug boot parameters like 'shell' and 'debug', see# meta/recipes-core/initrdscripts/initramfs-framework/debug for details # Could be removed in more minimal product image PACKAGE_INSTALL += "initramfs-module-debug"Could you, please, review these lines and fix, if something is not correct?
I what I understood, this does the magic, but you could not stop in initramfs shell? Still, this problem is not solved?
Quoted 9 lines
I was following this site: https://wiki.debian.org/InitramfsDebug
Rescue shell (also known as initramfs shell)
Read man initramfs-tools to learn about the break=something kernel parameter (where valid arguments for something are: top, modules, premount, mount, mountroot, bottom, init), which starts a debug shell. You can try, for example, break=premount. You can edit/boot/grub/grub.cfgto add this to the end of the kernel line, or you can do it interactively from the grub boot menu: "e" to edit, and "b" to boot once you've edited the kernel line.Now, as my understanding is, you solved this problem actually adding to grub.cfg in command kernel line break=premount, and was able to stop in rescue shell?! Am I correct here?
Thank you,
Zoran
_______Quoted 215 lines · Moritz Porst
Hello,
I think I found the issue. ( see below )On 01.07.19 15:57, Zoran Stojsavljevic wrote:
Hello Moritz,
Too hot here, in Belgrade... Where I am resting for the Time being (actually, this message given to my invisible spying security "angels" on this list)... :-) Projected +38C degrees today. Too hot for this too old Siberian untouchable bobcat!
Luckily it's a rather cold day in germany, thanks that you still take the time to answer !
I started from the core-image-minimal to have a small image and extended it with the features I need, which is e.g. a graphical system. The console=[...] part in the kernel command line is probably a remnant but my image boots into the GUI. Is this a problem ?
Nope, it is not. If you need to do it correctly, you should use bitbake -k core-image-sato build command (my best educated guess). Then, I do not feel comfortable seeing in your kernel command line serial interface, do you agree?
Yes that is true.
YOCTO maintainers, any additional
advices?My bootloader is currently grub, the EFI is AM.
Nope. Eeeeeeeeek. Wrong. Currently, your boot-loader is UEFI AMI. Your OS (Linux probably, U name it) boot-loader is GRUB2. Let us keep it contained, sane and sober.
Sorry but I can't find this info in the EFI.
Could you, please try the following command being root: dmesg | grep MCU. or grep mcu, or grep CPUID or grep cpuid?? Please, post results to this list (to me).
No luck unfortunately (used grep -i)
Could you, also, send to YOCTO list/me attached file:
/boot/microcode.cpioso I can somehow (?) inspect it? ;-)I send it to you directly, so I don't spam the list with a large attachment.
2GB, single channel.
All Cool. E3825 by HW/silicon design could/does NOT support multiple memory channels. ONLY single... But even YOCTO primes (INTEL ones from this list) are not gonna tell this to you. Not 'cause they are nasty. They are NOT aware/they are ignorant (with the purpose)! ;-))
No, the boot does not stop. Even if I do issue "break=premount" I end up in my graphical interface with the rootfs mounted. This is the last message in the log: EXT4-fs (sdb2): re-mounted. Opts: (null) The rootfs partition is always 2, so either
/dev/sda2or/dev/sdb2(when booting from stick)Yes, from https://pastebin.com/ya7iCtq7, so it is remounted rw, not read only. So, it seems that you have passed dracut phase. and mounted SD or flash rootfs. So, initramfs is NOT your true problem, is it???
The thing is that the boot works but I want an initramfs that can be used for updating (in case the rootfs is broken). However I need to be able to intercept the boot process there because otherwise I can't deploy an update mechanism, that's what I was trying.
Zoran
_______No, the boot does not stop. Even if I do issue "break=premount" I end up in my graphical interface with the rootfs mounted. This is the last message in the log: EXT4-fs (sdb2): re-mounted. Opts: (null) The rootfs partition is always 2, so either
/dev/sda2or/dev/sdb2(when booting from stick)So for the issue...
I expected yocto to put the bundled bzImage onto my rootfs. This was not the case. My image directory contains 2x bzImage, one bundled and one unbundled. Apparently yocto puts the >un<bundled image onto my /boot partition and uses it for boot. So of course I couldn't access initramfs in this case. Now I get to the initramfs statement "dropping to shell" if I intentionally boot with wrong rootfs. Still I don't get the interactive shell.
On the github ostroproject site I found this:# debug: adds debug boot parameters like 'shell' and 'debug', see
# meta/recipes-core/initrdscripts/initramfs-framework/debug for details
# Could be removed in more minimal product image.PACKAGE_INSTALL+= "initramfs-module-debug"including the module-debug still does not enable me to get an interactive shell.
I was following this site: https://wiki.debian.org/InitramfsDebug
I am aware that yocto is no debian but I expected that kernel parameters (like 'break') would be independent of the distribution.Lastly I do not really need the interactive shell, it is enough if I can deploy a custom init script in the initramfs. Still I think that getting an initramfs shell should be as simple as stating the name of the initramfs image and setting the "
INITRAMFS_DO_BUNDLE" variable.Best regards
MoritzOn Mon, Jul 1, 2019 at 11:20 AM Moritz Porst <[email protected]> wrote:
Hello Zoran,
thanks for your answerOn 28.06.19 14:26, Zoran Stojsavljevic wrote:
INITRAMFS_IMAGE= "core-image-minimal-initramfs"INITRAMFS_IMAGE_BUNDLE= "1"...
You can find the
/var/log/dmesghere: https://pastebin.com/ya7iCtq7ISome hints...
[1] Kernel command line: BOOT_IMAGE=/bzImage root=PARTUUID=71d1d94a-83e8-4895-98eb-35309f58119f break=premount quiet rootwait rootwait rootfstype=ext4 console=ttyS0,115200 console=tty0
input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input7
fbcon: inteldrmfb (fb0) is primary device
Console: switching to colour frame buffer device 128x48
i915 0000:00:02.0: fb0: inteldrmfb frame buffer devicesnd_hda_intel0000:00:1b.0: bound 0000:00:02.0 (opsi915_audio_component_bind_ops[i915])Hmmmmm... You are using console and serial, but full i915 GFX kernel driver is still included in the build???
I started from the core-image-minimal to have a small image and extended it with the features I need, which is e.g. a graphical system. The console=[...] part in the kernel command line is probably a remnant but my image boots into the GUI. Is this a problem ?
[2] efi: EFI v2.31 by American Megatrends
Using AMI BIOS as boot loader FW... OK?! Am I correct?
My bootloader is currently grub, the EFI is AM.
[3] smpboot: CPU0: Intel(R) Atom(TM) CPU E3825 @ 1.33GHz (family:
0x6, model:0x37, stepping:0x9)This is CPUID ID
0x30679, which uses MCU... Which MicroCodeUnit? M0130679xxx (info from AMI BIOS)?Sorry but I can't find this info in the EFI
[4] Using INTEL ATOM BYT E3825 dual core (sans Hyper-threading), implies that you are using 4GB (e820 messages) as single channel (one memory module DDR3 as 4GB)! Am I correct (important)?
2GB, single channel.
[5] Dracut phase?!
To my understanding the initramfs should be embedded in
/boot/bzImage. However since I use an intel platform I also have a/boot/microcode.cpiowhich gets loaded via "initrd /microcode.cpio". Removing this line in grub does not enable me to get an initramfs prompt either (again, using break as option).You are obviously stopping in boot phase called dracut. Please, try to mount by hand /dev/sda(whatever)... You should use fdisk -l command, or do ls -al /dev | grep sda to dig out which partition you need to mount to /tmp dir to see rootfstype=ext4 (HDD/SSD)
No, the boot does not stop. Even if I do issue "break=premount" I end up in my graphical interface with the rootfs mounted. This is the last message in the log:
EXT4-fs (sdb2): re-mounted. Opts: (null)
The rootfs partition is always 2, so either/dev/sda2or/dev/sdb2(when booting from stick)_______
Just thinking loud... .. .
Hope this helps (has very little to do with YOCTO build system, BTW) . ;-)
Zoran
_______On Fri, Jun 28, 2019 at 11:22 AM Moritz Porst <[email protected]> wrote:
Hello,
I currently try to deploy a single rootfs update mechanism for my embedded device. I can't boot to initramfs using either "break" or "break=premount" (without quotes...). I tried this in systemd-boot and grub-efi (always efi boot) but the boot process just continues normally. If I insert at the same point e.g. "quiet" this argument is recognised. I boot the .wic image with a separate boot partition from a USB stick. in local.conf I have set:INITRAMFS_IMAGE= "core-image-minimal-initramfs"INITRAMFS_IMAGE_BUNDLE= "1"In order to reduce complexity I now use the standard core-image-minimal-initramfs without .bbappend. I can confirm (from seeing the task) that bitbake bundled the kernel with the initramfs.
You can find the
/var/log/dmesghere: https://pastebin.com/ya7iCtq7To my understanding the initramfs should be embedded in
/boot/bzImage. However since I use an intel platform I also have a/boot/microcode.cpiowhich gets loaded via "initrd /microcode.cpio". Removing this line in grub does not enable me to get an initramfs prompt either (again, using break as option).Did I forget some configuration or do I have to put the break statement at a very specific position within the "linux ..." boot command ? Do you know which bitbake variables to check ? (both set in local.conf do not get overwritten, already checked this). I got the thud branch checked out in all my meta-layers except for meta-qt which is currently on master branch.
Help is much appreciated !
Best regards
Moritz--
_______________________________________________
yocto mailing list
[email protected]
https://lists.yoctoproject.org/listinfo/yocto
Forgot to CC Jupiter and the most important thing:
PACKAGE_INSTALL += "initramfs-module-debug" (To my understanding this enables the rescue shell)
Quoted 401 lines · Moritz Porst
Hey,
The only thing I can add to what I already said is my "core-image-minimal-initramfs.bbappend":
PACKAGE_INSTALL+= "\
busybox \
base-files \
base-passwd \
bash \
util-linux-lsblk \
vim \
"
Jupiter, are you able to produce your zImage-initramfs now ? If not further do the following:bitbake <your-image> -e > tempfile
[wait until done, then search]
grep <appropriate search word> tempfilewhere <appropriate search word> may be e.g.: zImage, zImage-initramfs,
INITRAMFS_IMAGE,INITRAMFS_IMAGE_BUNDLE
Especially check that all variables you set are not overwritten somewhere elseBest regards
MoritzQuoted 373 lines · Zoran Stojsavljevic
Moritz,
Thank you very much for this reply. It makes it very clear... What is the current State of Affairs for the topic.
Let us see if there will be the improvement to this topic. I'll document this on one of my private GitHubs. And archive this email.
Zoran
_______Quoted 360 lines · Moritz Porst
Hello Zoran, Jupiter and list
The configuration you sent seems to be correct.
As I already said initramfs seems overly complicated in yocto. the most important thing to note is that 2 kernel images are created, one is called bzImage (in my case) an the other bzImage-initramfs. However only
the bzImage is written into the rootfs so you have to exchange them manually. (in/boot/bzImage). I did not find a way of including the bundled kernel right away.What you can do is to build core-image-minimal-initramfs and delete the symbolic link "bzImage", then recreate it and let it point to bzImage-initramfs. However this is rather a hack than a solution.
An other mistake I made was to use
IMAGE_INSTALL_appendwhich is ignored. UsePACKAGE_INSTALL_append.Also I found that "break" does not work as a kernel parameter. Use "shell" oder "debug-shell" instead. If you want to try to boot into initramfs you can remove all parameters to the booting line so you either end up in a kernel panic (initramfs doesn't work) or in the rescue shell (initramfs works).
In the end I actually managed to get a working shell, but I often ended up in initramfs telling me "dropping to shell..." but then freezing.
I don't have access to my files right now but I can tell you more on my setup tomorrow. In case the solution is not included above.
Best regards
MoritzQuoted 325 lines · Zoran Stojsavljevic
Hello Moritz,
I need here some help from you. I'll try to reconstruct the parts of the local.conf you are using, so I (and Jupiter) can understand what should we do to also bundle kernel image with initramfs, to end up in Dracut/rescue shell.
Here is what I anticipate after reading several YOCTO @ threads:
IMAGE_FSTYPES_append= " cpio.gz"INITRAMFS_IMAGE= "core-image-minimal-initramfs"INITRAMFS_IMAGE_BUNDLE= "1"
# debug: adds debug boot parameters like 'shell' and 'debug', see# meta/recipes-core/initrdscripts/initramfs-framework/debug for details # Could be removed in more minimal product image PACKAGE_INSTALL += "initramfs-module-debug"Could you, please, review these lines and fix, if something is not correct?
I what I understood, this does the magic, but you could not stop in initramfs shell? Still, this problem is not solved?
Quoted 5 lines
I was following this site: https://wiki.debian.org/InitramfsDebug
Rescue shell (also known as initramfs shell)
Read man initramfs-tools to learn about the break=something kernel parameter (where valid arguments for something are: top, modules, premount, mount, mountroot, bottom, init), which starts a debugQuoted 8 lines
shell.
You can try, for example, break=premount. You can edit/boot/grub/grub.cfg
to add this to the end of the kernel line, or you can do it interactively
from the grub boot menu: "e" to edit, and "b" to boot once you've edited
the kernel line.Now, as my understanding is, you solved this problem actually adding to grub.cfg in command kernel line break=premount, and was able to stop in rescue shell?! Am I correct here?
Thank you,
Zoran
_______Quoted 277 lines · Moritz Porst
Hello,
I think I found the issue. ( see below )On 01.07.19 15:57, Zoran Stojsavljevic wrote:
Hello Moritz,
Too hot here, in Belgrade... Where I am resting for the Time being (actually, this message given to my invisible spying security "angels"
on this list)... :-) Projected +38C degrees today. Too hot for this too old Siberian untouchable bobcat!Luckily it's a rather cold day in germany, thanks that you still take the time to answer !
I started from the core-image-minimal to have a small image and extended it with the features I need, which is e.g. a graphical system.
The console=[...] part in the kernel command line is probably a remnant but my image boots into the GUI. Is this a problem ?Nope, it is not. If you need to do it correctly, you should use bitbake -k core-image-sato build command (my best educated guess). Then, I do not feel comfortable seeing in your kernel command line serial interface, do you agree?
Yes that is true.
YOCTO maintainers, any additional
advices?My bootloader is currently grub, the EFI is AM.
Nope. Eeeeeeeeek. Wrong. Currently, your boot-loader is UEFI AMI. Your
OS (Linux probably, U name it) boot-loader is GRUB2. Let us keep it contained, sane and sober.Sorry but I can't find this info in the EFI.
Could you, please try the following command being root: dmesg | grep MCU. or grep mcu, or grep CPUID or grep cpuid?? Please, post results to this list (to me).
No luck unfortunately (used grep -i)
Could you, also, send to YOCTO list/me attached file:
/boot/microcode.cpioso I can somehow (?) inspect it? ;-)I send it to you directly, so I don't spam the list with a large attachment.
2GB, single channel.
All Cool. E3825 by HW/silicon design could/does NOT support multiple memory channels. ONLY single... But even YOCTO primes (INTEL ones from
this list) are not gonna tell this to you. Not 'cause they are nasty. They are NOT aware/they are ignorant (with the purpose)! ;-))No, the boot does not stop. Even if I do issue "break=premount" I end up in my graphical interface with the rootfs mounted. This is the last message in the log: EXT4-fs (sdb2): re-mounted. Opts: (null) The rootfs partition is always 2, so either
/dev/sda2or/dev/sdb2(when booting from stick)Yes, from https://pastebin.com/ya7iCtq7, so it is remounted rw, not read only. So, it seems that you have passed dracut phase. and mounted
SD or flash rootfs. So, initramfs is NOT your true problem, is it???The thing is that the boot works but I want an initramfs that can be used for updating (in case the rootfs is broken). However I need to be able to intercept the boot process there because otherwise I can't deploy an update mechanism, that's what I was trying.
Zoran
_______No, the boot does not stop. Even if I do issue "break=premount" I end up
in my graphical interface with the rootfs mounted. This is the last message
in the log: EXT4-fs (sdb2): re-mounted. Opts: (null) The rootfs partition is
always 2, so either/dev/sda2or/dev/sdb2(when booting from stick)So for the issue...
I expected yocto to put the bundled bzImage onto my rootfs. This was not the case. My image directory contains 2x bzImage, one bundled and one unbundled. Apparently yocto puts the >un<bundled image onto my /boot partition and uses it for boot. So of course I couldn't access initramfs in this case. Now I get to the initramfs statement "dropping to shell" if I intentionally boot with wrong rootfs.
Still I don't get the interactive shell.
On the github ostroproject site I found this:# debug: adds debug boot parameters like 'shell' and 'debug', see
# meta/recipes-core/initrdscripts/initramfs-framework/debug for details # Could be removed in more minimal product image. PACKAGE_INSTALL += "initramfs-module-debug"including the module-debug still does not enable me to get an interactive shell.
I was following this site: https://wiki.debian.org/InitramfsDebug
I am aware that yocto is no debian but I expected that kernel parameters (like 'break') would be independent of the distribution.Lastly I do not really need the interactive shell, it is enough if I can deploy a custom init script in the initramfs. Still I think that getting an initramfs shell should be as simple as stating the name of the initramfs image and setting the "
INITRAMFS_DO_BUNDLE" variable.Best regards
MoritzOn Mon, Jul 1, 2019 at 11:20 AM Moritz Porst <[email protected]> wrote:
Hello Zoran,
thanks for your answerOn 28.06.19 14:26, Zoran Stojsavljevic wrote:
INITRAMFS_IMAGE= "core-image-minimal-initramfs"INITRAMFS_IMAGE_BUNDLE= "1"...
You can find the
/var/log/dmesghere: https://pastebin.com/ya7iCtq7ISome hints...
[1] Kernel command line: BOOT_IMAGE=/bzImage root=PARTUUID=71d1d94a-83e8-4895-98eb-35309f58119f break=premount quiet rootwait rootwait rootfstype=ext4 console=ttyS0,115200 console=tty0
input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input7
fbcon: inteldrmfb (fb0) is primary device
Console: switching to colour frame buffer device 128x48 i915 0000:00:02.0: fb0: inteldrmfb frame buffer devicesnd_hda_intel0000:00:1b.0: bound 0000:00:02.0 (opsi915_audio_component_bind_ops[i915])Hmmmmm... You are using console and serial, but full i915 GFX kernel driver is still included in the build???
I started from the core-image-minimal to have a small image and extended it with the features I need, which is e.g. a graphical system. The console=[...] part in the kernel command line is probably a remnant but my image boots into the GUI. Is this a problem ?
[2] efi: EFI v2.31 by American Megatrends
Using AMI BIOS as boot loader FW... OK?! Am I correct?
My bootloader is currently grub, the EFI is AM.
[3] smpboot: CPU0: Intel(R) Atom(TM) CPU E3825 @ 1.33GHz (family:
0x6, model:0x37, stepping:0x9)This is CPUID ID
0x30679, which uses MCU... Which MicroCodeUnit? M0130679xxx (info from AMI BIOS)?Sorry but I can't find this info in the EFI
[4] Using INTEL ATOM BYT E3825 dual core (sans Hyper-threading), implies that you are using
4GB (e820 messages) as single channel (one memory module DDR3 as 4GB)! Am I correct (important)?2GB, single channel.
[5] Dracut phase?!
To my understanding the initramfs should be embedded in
/boot/bzImage.
However since I use an intel platform I also have a/boot/microcode.cpio
which gets loaded via "initrd /microcode.cpio". Removing this line in grub does not enable me to get an initramfs prompt either (again, using
break as option).You are obviously stopping in boot phase called dracut. Please, try to mount by hand
/dev/sda(whatever)... You should use fdisk -l command, or do ls -al /dev | grep sda to
dig out which partition you need to mount to /tmp dir to see rootfstype=ext4 (HDD/SSD)No, the boot does not stop. Even if I do issue "break=premount" I end up in my graphical interface with the rootfs mounted. This is the last message in the log:
EXT4-fs (sdb2): re-mounted. Opts: (null)
The rootfs partition is always 2, so either/dev/sda2or/dev/sdb2(when booting from stick)_______
Just thinking loud... .. .
Hope this helps (has very little to do with YOCTO build system, BTW) . ;-)
Zoran
_______On Fri, Jun 28, 2019 at 11:22 AM Moritz Porst
<[email protected]> wrote:Hello,
I currently try to deploy a single rootfs update mechanism for my embedded device. I can't boot to initramfs using either "break" or "break=premount" (without quotes...). I tried this in systemd-boot and
grub-efi (always efi boot) but the boot process just continues normally.
If I insert at the same point e.g. "quiet" this argument is recognised.
I boot the .wic image with a separate boot partition from a USB stick.
in local.conf I have set:INITRAMFS_IMAGE= "core-image-minimal-initramfs"INITRAMFS_IMAGE_BUNDLE= "1"In order to reduce complexity I now use the standard core-image-minimal-initramfs without .bbappend. I can confirm (from seeing the task) that bitbake bundled the kernel with the initramfs.
You can find the
/var/log/dmesghere: https://pastebin.com/ya7iCtq7To my understanding the initramfs should be embedded in
/boot/bzImage.
However since I use an intel platform I also have a/boot/microcode.cpio
which gets loaded via "initrd /microcode.cpio". Removing this line in grub does not enable me to get an initramfs prompt either (again, using
break as option).Did I forget some configuration or do I have to put the break statement
at a very specific position within the "linux ..." boot command ? Do you
know which bitbake variables to check ? (both set in local.conf do not
get overwritten, already checked this). I got the thud branch checked out in all my meta-layers except for meta-qt which is currently on master branch.Help is much appreciated !
Best regards
Moritz--
_______________________________________________
yocto mailing list
[email protected]
https://lists.yoctoproject.org/listinfo/yocto
Hi Moritz,
I could not find zImage-initramfs:
$ grep zImage tempfile
ARCH_DEFAULT_KERNELIMAGETYPE="bzImage"
KERNEL_IMAGETYPE="bzImage"
KERNEL_IMAGETYPES="bzImage"
QB_DEFAULT_KERNEL="bzImage"
$ grep zImage-initramfs tempfile
$ grep INITRAMFS_IMAGE_BUNDLE tempfile
# $INITRAMFS_IMAGE_BUNDLE
INITRAMFS_IMAGE_BUNDLE="1"
$ grep INITRAMFS_FSTYPES tempfile INITRAMFS_FSTYPES="cpio.gz"
I added PACKAGE_INSTALL += "initramfs-module-debug" and I added "core-image-minimal-initramfs.bbappend" coppied from yours:
$ cat core-image-minimal-initramfs.bbappend
PACKAGE_INSTALL += "\
busybox \
base-files \
base-passwd \
bash \
util-linux-lsblk \
vim \
"But I still have troubles to add INITRAMFS_IMAGE = "core-image-minimal-initramfs" or to run core-image-minimal-initramfs, both had errors:
$ MACHINE="solar" DISTRO="solar" bitbake core-image-minimal-initramfs
ERROR: Nothing PROVIDES 'core-image-minimal-initramfs' core-image-minimal-initramfs was skipped: incompatible with host arm-oe-linux-gnueabi (not in COMPATIBLE_HOST)
$ MACHINE="solar" DISTRO="solar" bitbake solar-image
ERROR: Nothing PROVIDES 'core-image-minimal-initramfs' core-image-minimal-initramfs was skipped: incompatible with host arm-oe-linux-gnueabi (not in COMPATIBLE_HOST)
ERROR: Required build target 'solar-image' has no buildable providers. Missing or unbuildable dependency chain was: ['solar-image', 'virtual/kernel', 'core-image-minimal-initramfs']
Sorry, still learning Yocto, what I could be missing?
Quoted 1 line
BOOT_IMAGE=/bzImage root=PARTUUID=71d1d94a-83e8-4895-98eb-35309f58119f
break=premount quiet rootwait rootwait rootfstype=ext4 console=ttyS0,115200 console=tty0
Which did you add kernel boot command for bootargs, bootcmd, etc as above? I could not find BOOT_IMAGE (I use meta-freescale)
Thank you very much.
- jupiter
Quoted 408 lines · Moritz Porst
Forgot to CC Jupiter and the most important thing:
PACKAGE_INSTALL+= "initramfs-module-debug" (To my understanding this
enables the rescue shell)Quoted 401 lines · Moritz Porst
Hey,
The only thing I can add to what I already said is my "core-image-minimal-initramfs.bbappend":
PACKAGE_INSTALL += "\ busybox \ base-files \ base-passwd \ bash \ util-linux-lsblk \ vim \ "Jupiter, are you able to produce your zImage-initramfs now ? If not further do the following:
bitbake <your-image> -e > tempfile
[wait until done, then search]
grep <appropriate search word> tempfilewhere <appropriate search word> may be e.g.: zImage, zImage-initramfs,
INITRAMFS_IMAGE,INITRAMFS_IMAGE_BUNDLE
Especially check that all variables you set are not overwritten somewhere elseBest regards
MoritzQuoted 373 lines · Zoran Stojsavljevic
Moritz,
Thank you very much for this reply. It makes it very clear... What is the current State of Affairs for the topic.
Let us see if there will be the improvement to this topic. I'll document this on one of my private GitHubs. And archive this email.
Zoran
_______Quoted 360 lines · Moritz Porst
Hello Zoran, Jupiter and list
The configuration you sent seems to be correct.
As I already said initramfs seems overly complicated in yocto. the most important thing to note is that 2 kernel images are created, one is called bzImage (in my case) an the other bzImage-initramfs. However only
the bzImage is written into the rootfs so you have to exchange them manually. (in/boot/bzImage). I did not find a way of including the bundled kernel right away.What you can do is to build core-image-minimal-initramfs and delete the symbolic link "bzImage", then recreate it and let it point to bzImage-initramfs. However this is rather a hack than a solution.
An other mistake I made was to use
IMAGE_INSTALL_appendwhich is ignored. UsePACKAGE_INSTALL_append.Also I found that "break" does not work as a kernel parameter. Use "shell" oder "debug-shell" instead. If you want to try to boot into initramfs you can remove all parameters to the booting line so you either end up in a kernel panic (initramfs doesn't work) or in the rescue shell (initramfs works).
In the end I actually managed to get a working shell, but I often ended up in initramfs telling me "dropping to shell..." but then freezing.
I don't have access to my files right now but I can tell you more on my setup tomorrow. In case the solution is not included above.
Best regards
MoritzQuoted 325 lines · Zoran Stojsavljevic
Hello Moritz,
I need here some help from you. I'll try to reconstruct the parts of the local.conf you are using, so I (and Jupiter) can understand what should we do to also bundle kernel image with initramfs, to end up in Dracut/rescue shell.
Here is what I anticipate after reading several YOCTO @ threads:
IMAGE_FSTYPES_append= " cpio.gz"INITRAMFS_IMAGE= "core-image-minimal-initramfs"INITRAMFS_IMAGE_BUNDLE= "1"
# debug: adds debug boot parameters like 'shell' and 'debug', see# meta/recipes-core/initrdscripts/initramfs-framework/debug for details # Could be removed in more minimal product image PACKAGE_INSTALL += "initramfs-module-debug"Could you, please, review these lines and fix, if something is not correct?
I what I understood, this does the magic, but you could not stop in initramfs shell? Still, this problem is not solved?
Quoted 5 lines
I was following this site: https://wiki.debian.org/InitramfsDebug
Rescue shell (also known as initramfs shell)
Read man initramfs-tools to learn about the break=something kernel parameter (where valid arguments for something are: top, modules, premount, mount, mountroot, bottom, init), which starts a debugQuoted 8 lines
shell.
You can try, for example, break=premount. You can edit/boot/grub/grub.cfg
to add this to the end of the kernel line, or you can do it interactively
from the grub boot menu: "e" to edit, and "b" to boot once you've edited
the kernel line.Now, as my understanding is, you solved this problem actually adding to grub.cfg in command kernel line break=premount, and was able to stop in rescue shell?! Am I correct here?
Thank you,
Zoran
_______Quoted 277 lines · Moritz Porst
Hello,
I think I found the issue. ( see below )On 01.07.19 15:57, Zoran Stojsavljevic wrote:
Hello Moritz,
Too hot here, in Belgrade... Where I am resting for the Time being (actually, this message given to my invisible spying security "angels"
on this list)... :-) Projected +38C degrees today. Too hot for this too old Siberian untouchable bobcat!Luckily it's a rather cold day in germany, thanks that you still take the time to answer !
I started from the core-image-minimal to have a small image and extended it with the features I need, which is e.g. a graphical system.
The console=[...] part in the kernel command line is probably a remnant but my image boots into the GUI. Is this a problem ?Nope, it is not. If you need to do it correctly, you should use bitbake -k core-image-sato build command (my best educated guess). Then, I do not feel comfortable seeing in your kernel command line serial interface, do you agree?
Yes that is true.
YOCTO maintainers, any additional
advices?My bootloader is currently grub, the EFI is AM.
Nope. Eeeeeeeeek. Wrong. Currently, your boot-loader is UEFI AMI. Your
OS (Linux probably, U name it) boot-loader is GRUB2. Let us keep it contained, sane and sober.Sorry but I can't find this info in the EFI.
Could you, please try the following command being root: dmesg | grep MCU. or grep mcu, or grep CPUID or grep cpuid?? Please, post results to this list (to me).
No luck unfortunately (used grep -i)
Could you, also, send to YOCTO list/me attached file:
/boot/microcode.cpioso I can somehow (?) inspect it? ;-)I send it to you directly, so I don't spam the list with a large attachment.
2GB, single channel.
All Cool. E3825 by HW/silicon design could/does NOT support multiple memory channels. ONLY single... But even YOCTO primes (INTEL ones from
this list) are not gonna tell this to you. Not 'cause they are nasty. They are NOT aware/they are ignorant (with the purpose)! ;-))No, the boot does not stop. Even if I do issue "break=premount" I end up in my graphical interface with the rootfs mounted. This is the last message in the log: EXT4-fs (sdb2): re-mounted. Opts: (null) The rootfs partition is always 2, so either
/dev/sda2or/dev/sdb2(when booting from stick)Yes, from https://pastebin.com/ya7iCtq7, so it is remounted rw, not read only. So, it seems that you have passed dracut phase. and mounted
SD or flash rootfs. So, initramfs is NOT your true problem, is it???The thing is that the boot works but I want an initramfs that can be used for updating (in case the rootfs is broken). However I need to be able to intercept the boot process there because otherwise I can't deploy an update mechanism, that's what I was trying.
Zoran
_______No, the boot does not stop. Even if I do issue "break=premount" I end up
in my graphical interface with the rootfs mounted. This is the last message
in the log: EXT4-fs (sdb2): re-mounted. Opts: (null) The rootfs partition is
always 2, so either/dev/sda2or/dev/sdb2(when booting from stick)So for the issue...
I expected yocto to put the bundled bzImage onto my rootfs. This was not the case. My image directory contains 2x bzImage, one bundled and one unbundled. Apparently yocto puts the >un<bundled image onto my /boot partition and uses it for boot. So of course I couldn't access initramfs in this case. Now I get to the initramfs statement "dropping to shell" if I intentionally boot with wrong rootfs.
Still I don't get the interactive shell.
On the github ostroproject site I found this:# debug: adds debug boot parameters like 'shell' and 'debug', see
# meta/recipes-core/initrdscripts/initramfs-framework/debug for details # Could be removed in more minimal product image. PACKAGE_INSTALL += "initramfs-module-debug"including the module-debug still does not enable me to get an interactive shell.
I was following this site: https://wiki.debian.org/InitramfsDebug
I am aware that yocto is no debian but I expected that kernel parameters (like 'break') would be independent of the distribution.Lastly I do not really need the interactive shell, it is enough if I can deploy a custom init script in the initramfs. Still I think that getting an initramfs shell should be as simple as stating the name of the initramfs image and setting the "
INITRAMFS_DO_BUNDLE" variable.Best regards
MoritzOn Mon, Jul 1, 2019 at 11:20 AM Moritz Porst <[email protected]> wrote:
Hello Zoran,
thanks for your answerOn 28.06.19 14:26, Zoran Stojsavljevic wrote:
INITRAMFS_IMAGE= "core-image-minimal-initramfs"INITRAMFS_IMAGE_BUNDLE= "1"...
You can find the
/var/log/dmesghere: https://pastebin.com/ya7iCtq7ISome hints...
[1] Kernel command line: BOOT_IMAGE=/bzImage root=PARTUUID=71d1d94a-83e8-4895-98eb-35309f58119f break=premount quiet rootwait rootwait rootfstype=ext4 console=ttyS0,115200 console=tty0
input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input7
fbcon: inteldrmfb (fb0) is primary device
Console: switching to colour frame buffer device 128x48 i915 0000:00:02.0: fb0: inteldrmfb frame buffer devicesnd_hda_intel0000:00:1b.0: bound 0000:00:02.0 (opsi915_audio_component_bind_ops[i915])Hmmmmm... You are using console and serial, but full i915 GFX kernel driver is still included in the build???
I started from the core-image-minimal to have a small image and extended it with the features I need, which is e.g. a graphical system. The console=[...] part in the kernel command line is probably a remnant but my image boots into the GUI. Is this a problem ?
[2] efi: EFI v2.31 by American Megatrends
Using AMI BIOS as boot loader FW... OK?! Am I correct?
My bootloader is currently grub, the EFI is AM.
[3] smpboot: CPU0: Intel(R) Atom(TM) CPU E3825 @ 1.33GHz (family:
0x6, model:0x37, stepping:0x9)This is CPUID ID
0x30679, which uses MCU... Which MicroCodeUnit? M0130679xxx (info from AMI BIOS)?Sorry but I can't find this info in the EFI
[4] Using INTEL ATOM BYT E3825 dual core (sans Hyper-threading), implies that you are using
4GB (e820 messages) as single channel (one memory module DDR3 as 4GB)! Am I correct (important)?2GB, single channel.
[5] Dracut phase?!
To my understanding the initramfs should be embedded in
/boot/bzImage.
However since I use an intel platform I also have a/boot/microcode.cpio
which gets loaded via "initrd /microcode.cpio". Removing this line in grub does not enable me to get an initramfs prompt either (again, using
break as option).You are obviously stopping in boot phase called dracut. Please, try to mount by hand
/dev/sda(whatever)... You should use fdisk -l command, or do ls -al /dev | grep sda to
dig out which partition you need to mount to /tmp dir to see rootfstype=ext4 (HDD/SSD)No, the boot does not stop. Even if I do issue "break=premount" I end up in my graphical interface with the rootfs mounted. This is the last message in the log:
EXT4-fs (sdb2): re-mounted. Opts: (null)
The rootfs partition is always 2, so either/dev/sda2or/dev/sdb2(when booting from stick)_______
Just thinking loud... .. .
Hope this helps (has very little to do with YOCTO build system, BTW) . ;-)
Zoran
_______On Fri, Jun 28, 2019 at 11:22 AM Moritz Porst
<[email protected]> wrote:Hello,
I currently try to deploy a single rootfs update mechanism for my embedded device. I can't boot to initramfs using either "break" or "break=premount" (without quotes...). I tried this in systemd-boot and
grub-efi (always efi boot) but the boot process just continues normally.
If I insert at the same point e.g. "quiet" this argument is recognised.
I boot the .wic image with a separate boot partition from a USB stick.
in local.conf I have set:INITRAMFS_IMAGE= "core-image-minimal-initramfs"INITRAMFS_IMAGE_BUNDLE= "1"In order to reduce complexity I now use the standard core-image-minimal-initramfs without .bbappend. I can confirm (from seeing the task) that bitbake bundled the kernel with the initramfs.
You can find the
/var/log/dmesghere: https://pastebin.com/ya7iCtq7To my understanding the initramfs should be embedded in
/boot/bzImage.
However since I use an intel platform I also have a/boot/microcode.cpio
which gets loaded via "initrd /microcode.cpio". Removing this line in grub does not enable me to get an initramfs prompt either (again, using
break as option).Did I forget some configuration or do I have to put the break statement
at a very specific position within the "linux ..." boot command ? Do you
know which bitbake variables to check ? (both set in local.conf do not
get overwritten, already checked this). I got the thud branch checked out in all my meta-layers except for meta-qt which is currently on master branch.Help is much appreciated !
Best regards
Moritz--
_______________________________________________
yocto mailing list
[email protected]
https://lists.yoctoproject.org/listinfo/yocto
Quoted 1 line
BOOT_IMAGE=/bzImage root=PARTUUID=71d1d94a-83e8-4895-98eb-35309f58119f
break=premount quiet rootwait rootwait rootfstype=ext4 console=ttyS0,115200 console=tty0
Which file did you add kernel boot command for bootargs, bootcmd, etc?
I use meta-freescale, but I could not find BOOT_IMAGE is defined.
Thank you
Quoted 486 lines · JH
Hi Moritz,
I could not find zImage-initramfs:
$ grep zImage tempfileARCH_DEFAULT_KERNELIMAGETYPE="bzImage"
KERNEL_IMAGETYPE="bzImage"
KERNEL_IMAGETYPES="bzImage"
QB_DEFAULT_KERNEL="bzImage"$ grep zImage-initramfs tempfile$ grep INITRAMFS_IMAGE_BUNDLE tempfile# $INITRAMFS_IMAGE_BUNDLE
INITRAMFS_IMAGE_BUNDLE="1"$ grep INITRAMFS_FSTYPES tempfile INITRAMFS_FSTYPES="cpio.gz"I added
PACKAGE_INSTALL+= "initramfs-module-debug" and I added "core-image-minimal-initramfs.bbappend" coppied from yours:$ cat core-image-minimal-initramfs.bbappendPACKAGE_INSTALL += "\ busybox \ base-files \ base-passwd \ bash \ util-linux-lsblk \ vim \ "But I still have troubles to add
INITRAMFS_IMAGE= "core-image-minimal-initramfs" or to run core-image-minimal-initramfs, both had errors:$ MACHINE="solar" DISTRO="solar" bitbake core-image-minimal-initramfsERROR: Nothing PROVIDES 'core-image-minimal-initramfs' core-image-minimal-initramfs was skipped: incompatible with host arm-oe-linux-gnueabi (not in
COMPATIBLE_HOST)$ MACHINE="solar" DISTRO="solar" bitbake solar-imageERROR: Nothing PROVIDES 'core-image-minimal-initramfs' core-image-minimal-initramfs was skipped: incompatible with host arm-oe-linux-gnueabi (not in
COMPATIBLE_HOST)
ERROR: Required build target 'solar-image' has no buildable providers. Missing or unbuildable dependency chain was: ['solar-image', 'virtual/kernel', 'core-image-minimal-initramfs']Sorry, still learning Yocto, what I could be missing?
Quoted 1 line
BOOT_IMAGE=/bzImage root=PARTUUID=71d1d94a-83e8-4895-98eb-35309f58119f
break=premount quiet rootwait rootwait rootfstype=ext4 console=ttyS0,115200 console=tty0
Which did you add kernel boot command for bootargs, bootcmd, etc as above? I could not find
BOOT_IMAGE(I use meta-freescale)Thank you very much.
- jupiter
Quoted 417 lines · Moritz Porst
Forgot to CC Jupiter and the most important thing:
PACKAGE_INSTALL+= "initramfs-module-debug" (To my understanding this
enables the rescue shell)Quoted 410 lines · Moritz Porst
Hey,
The only thing I can add to what I already said is my "core-image-minimal-initramfs.bbappend":
PACKAGE_INSTALL += "\ busybox \ base-files \ base-passwd \ bash \ util-linux-lsblk \ vim \ "Jupiter, are you able to produce your zImage-initramfs now ? If not further do the following:
bitbake <your-image> -e > tempfile
[wait until done, then search]
grep <appropriate search word> tempfilewhere <appropriate search word> may be e.g.: zImage, zImage-initramfs,
INITRAMFS_IMAGE,INITRAMFS_IMAGE_BUNDLE
Especially check that all variables you set are not overwritten somewhere elseBest regards
MoritzQuoted 382 lines · Zoran Stojsavljevic
Moritz,
Thank you very much for this reply. It makes it very clear... What is the current State of Affairs for the topic.
Let us see if there will be the improvement to this topic. I'll document this on one of my private GitHubs. And archive this email.
Zoran
_______Quoted 369 lines · Moritz Porst
Hello Zoran, Jupiter and list
The configuration you sent seems to be correct.
As I already said initramfs seems overly complicated in yocto. the most
important thing to note is that 2 kernel images are created, one is called bzImage (in my case) an the other bzImage-initramfs. However only
the bzImage is written into the rootfs so you have to exchange them manually. (in/boot/bzImage). I did not find a way of including the bundled kernel right away.What you can do is to build core-image-minimal-initramfs and delete the
symbolic link "bzImage", then recreate it and let it point to bzImage-initramfs. However this is rather a hack than a solution.An other mistake I made was to use
IMAGE_INSTALL_appendwhich is ignored. UsePACKAGE_INSTALL_append.Also I found that "break" does not work as a kernel parameter. Use "shell" oder "debug-shell" instead. If you want to try to boot into initramfs you can remove all parameters to the booting line so you either end up in a kernel panic (initramfs doesn't work) or in the rescue shell (initramfs works).
In the end I actually managed to get a working shell, but I often ended
up in initramfs telling me "dropping to shell..." but then freezing.I don't have access to my files right now but I can tell you more on my
setup tomorrow. In case the solution is not included above.Best regards
MoritzQuoted 330 lines · Zoran Stojsavljevic
Hello Moritz,
I need here some help from you. I'll try to reconstruct the parts of the local.conf you are using, so I (and Jupiter) can understand what should we do to also bundle kernel image with initramfs, to end up in Dracut/rescue shell.
Here is what I anticipate after reading several YOCTO @ threads:
IMAGE_FSTYPES_append= " cpio.gz"INITRAMFS_IMAGE= "core-image-minimal-initramfs"INITRAMFS_IMAGE_BUNDLE= "1"
# debug: adds debug boot parameters like 'shell' and 'debug', see# meta/recipes-core/initrdscripts/initramfs-framework/debug for details # Could be removed in more minimal product image PACKAGE_INSTALL += "initramfs-module-debug"Could you, please, review these lines and fix, if something is not correct?
I what I understood, this does the magic, but you could not stop in initramfs shell? Still, this problem is not solved?
Quoted 5 lines
I was following this site: https://wiki.debian.org/InitramfsDebug
Rescue shell (also known as initramfs shell)
Read man initramfs-tools to learn about the break=something kernel parameter (where valid arguments for something are: top, modules, premount, mount, mountroot, bottom, init), which starts a debugQuoted 8 lines
shell.
You can try, for example, break=premount. You can edit/boot/grub/grub.cfg
to add this to the end of the kernel line, or you can do it interactively
from the grub boot menu: "e" to edit, and "b" to boot once you've edited
the kernel line.Now, as my understanding is, you solved this problem actually adding to grub.cfg in command kernel line break=premount, and was able to stop in rescue shell?! Am I correct here?
Thank you,
Zoran
_______Quoted 282 lines · Moritz Porst
Hello,
I think I found the issue. ( see below )On 01.07.19 15:57, Zoran Stojsavljevic wrote:
Hello Moritz,
Too hot here, in Belgrade... Where I am resting for the Time being (actually, this message given to my invisible spying security "angels"
on this list)... :-) Projected +38C degrees today. Too hot for this too old Siberian untouchable bobcat!Luckily it's a rather cold day in germany, thanks that you still take the time to answer !
I started from the core-image-minimal to have a small image and extended it with the features I need, which is e.g. a graphical system.
The console=[...] part in the kernel command line is probably a remnant but my image boots into the GUI. Is this a problem ?Nope, it is not. If you need to do it correctly, you should use bitbake -k core-image-sato build command (my best educated guess). Then, I do not feel comfortable seeing in your kernel command line serial interface, do you agree?
Yes that is true.
YOCTO maintainers, any additional
advices?My bootloader is currently grub, the EFI is AM.
Nope. Eeeeeeeeek. Wrong. Currently, your boot-loader is UEFI AMI. Your
OS (Linux probably, U name it) boot-loader is GRUB2. Let us keep it contained, sane and sober.Sorry but I can't find this info in the EFI.
Could you, please try the following command being root: dmesg | grep MCU. or grep mcu, or grep CPUID or grep cpuid?? Please, post results to this list (to me).
No luck unfortunately (used grep -i)
Could you, also, send to YOCTO list/me attached file:
/boot/microcode.cpioso I can somehow (?) inspect it? ;-)I send it to you directly, so I don't spam the list with a large attachment.
2GB, single channel.
All Cool. E3825 by HW/silicon design could/does NOT support multiple memory channels. ONLY single... But even YOCTO primes (INTEL ones from
this list) are not gonna tell this to you. Not 'cause they are nasty.
They are NOT aware/they are ignorant (with the purpose)! ;-))No, the boot does not stop. Even if I do issue "break=premount" I end up in my graphical interface with the rootfs mounted. This is the
last message in the log: EXT4-fs (sdb2): re-mounted. Opts: (null) The rootfs partition is always 2, so either/dev/sda2or/dev/sdb2(when booting from stick)Yes, from https://pastebin.com/ya7iCtq7, so it is remounted rw, not read only. So, it seems that you have passed dracut phase. and mounted
SD or flash rootfs. So, initramfs is NOT your true problem, is it???The thing is that the boot works but I want an initramfs that can be used for updating (in case the rootfs is broken). However I need to be able to intercept the boot process there because otherwise I can't deploy an update mechanism, that's what I was trying.
Zoran
_______No, the boot does not stop. Even if I do issue "break=premount" I end up
in my graphical interface with the rootfs mounted. This is the last message
in the log: EXT4-fs (sdb2): re-mounted. Opts: (null) The rootfs partition is
always 2, so either/dev/sda2or/dev/sdb2(when booting from stick)So for the issue...
I expected yocto to put the bundled bzImage onto my rootfs. This was not the case. My image directory contains 2x bzImage, one bundled and one unbundled. Apparently yocto puts the >un<bundled image onto my /boot partition and uses it for boot. So of course I couldn't access initramfs in this case. Now I get to the initramfs statement "dropping to shell" if I intentionally boot with wrong rootfs.
Still I don't get the interactive shell.
On the github ostroproject site I found this:# debug: adds debug boot parameters like 'shell' and 'debug', see
# meta/recipes-core/initrdscripts/initramfs-framework/debug for details # Could be removed in more minimal product image. PACKAGE_INSTALL += "initramfs-module-debug"including the module-debug still does not enable me to get an interactive shell.
I was following this site: https://wiki.debian.org/InitramfsDebug
I am aware that yocto is no debian but I expected that kernel parameters (like 'break') would be independent of the distribution.Lastly I do not really need the interactive shell, it is enough if I can deploy a custom init script in the initramfs. Still I think that getting an initramfs shell should be as simple as stating the name of the initramfs image and setting the "
INITRAMFS_DO_BUNDLE" variable.Best regards
MoritzOn Mon, Jul 1, 2019 at 11:20 AM Moritz Porst <[email protected]> wrote:
Hello Zoran,
thanks for your answerOn 28.06.19 14:26, Zoran Stojsavljevic wrote:
INITRAMFS_IMAGE= "core-image-minimal-initramfs"INITRAMFS_IMAGE_BUNDLE= "1"...
You can find the
/var/log/dmesghere: https://pastebin.com/ya7iCtq7ISome hints...
[1] Kernel command line: BOOT_IMAGE=/bzImage root=PARTUUID=71d1d94a-83e8-4895-98eb-35309f58119f break=premount quiet rootwait rootwait rootfstype=ext4 console=ttyS0,115200 console=tty0
input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input7
fbcon: inteldrmfb (fb0) is primary device
Console: switching to colour frame buffer device 128x48 i915 0000:00:02.0: fb0: inteldrmfb frame buffer devicesnd_hda_intel0000:00:1b.0: bound 0000:00:02.0 (opsi915_audio_component_bind_ops[i915])Hmmmmm... You are using console and serial, but full i915 GFX kernel driver is still included in the build???
I started from the core-image-minimal to have a small image and extended it with the features I need, which is e.g. a graphical system. The console=[...] part in the kernel command line is probably a remnant but my image boots into the GUI. Is this a problem ?
[2] efi: EFI v2.31 by American Megatrends
Using AMI BIOS as boot loader FW... OK?! Am I correct?
My bootloader is currently grub, the EFI is AM.
[3] smpboot: CPU0: Intel(R) Atom(TM) CPU E3825 @ 1.33GHz (family:
0x6, model:0x37, stepping:0x9)This is CPUID ID
0x30679, which uses MCU... Which MicroCodeUnit? M0130679xxx (info from AMI BIOS)?Sorry but I can't find this info in the EFI
[4] Using INTEL ATOM BYT E3825 dual core (sans Hyper-threading), implies that you are using
4GB (e820 messages) as single channel (one memory module DDR3 as 4GB)! Am I correct (important)?2GB, single channel.
[5] Dracut phase?!
To my understanding the initramfs should be embedded in
/boot/bzImage.
However since I use an intel platform I also have a/boot/microcode.cpio
which gets loaded via "initrd /microcode.cpio". Removing this line in
grub does not enable me to get an initramfs prompt either (again, using
break as option).You are obviously stopping in boot phase called dracut. Please, try to mount by hand
/dev/sda(whatever)... You should use fdisk -l command, or do ls -al /dev | grep sda to
dig out which partition you need to mount to /tmp dir to see rootfstype=ext4 (HDD/SSD)No, the boot does not stop. Even if I do issue "break=premount" I end up in my graphical interface with the rootfs mounted. This is the last message in the log:
EXT4-fs (sdb2): re-mounted. Opts: (null)
The rootfs partition is always 2, so either/dev/sda2or/dev/sdb2(when booting from stick)_______
Just thinking loud... .. .
Hope this helps (has very little to do with YOCTO build system, BTW) . ;-)
Zoran
_______On Fri, Jun 28, 2019 at 11:22 AM Moritz Porst
<[email protected]> wrote:Hello,
I currently try to deploy a single rootfs update mechanism for my embedded device. I can't boot to initramfs using either "break" or "break=premount" (without quotes...). I tried this in systemd-boot and
grub-efi (always efi boot) but the boot process just continues normally.
If I insert at the same point e.g. "quiet" this argument is recognised.
I boot the .wic image with a separate boot partition from a USB stick.
in local.conf I have set:INITRAMFS_IMAGE= "core-image-minimal-initramfs"INITRAMFS_IMAGE_BUNDLE= "1"In order to reduce complexity I now use the standard core-image-minimal-initramfs without .bbappend. I can confirm (from seeing the task) that bitbake bundled the kernel with the initramfs.
You can find the
/var/log/dmesghere: https://pastebin.com/ya7iCtq7To my understanding the initramfs should be embedded in
/boot/bzImage.
However since I use an intel platform I also have a/boot/microcode.cpio
which gets loaded via "initrd /microcode.cpio". Removing this line in
grub does not enable me to get an initramfs prompt either (again, using
break as option).Did I forget some configuration or do I have to put the break statement
at a very specific position within the "linux ..." boot command ? Do you
know which bitbake variables to check ? (both set in local.conf do not
get overwritten, already checked this). I got the thud branch checked
out in all my meta-layers except for meta-qt which is currently on master branch.Help is much appreciated !
Best regards
Moritz--
_______________________________________________
yocto mailing list
[email protected]
https://lists.yoctoproject.org/listinfo/yocto
Hey
Quoted 7 lines · JH
Quoted 1 line
BOOT_IMAGE=/bzImage root=PARTUUID=71d1d94a-83e8-4895-98eb-35309f58119f
break=premount quiet rootwait rootwait rootfstype=ext4 console=ttyS0,115200 console=tty0
Which file did you add kernel boot command for bootargs, bootcmd, etc?
I use meta-freescale, but I could not find
BOOT_IMAGEis defined.
Ways I know to add boot arguments:
If you use .wic image via --append in the .wks file Otherwise in your machine config via the variable "APPEND", e.g. APPEND += "quiet shell"
the "BOOT_IMAGE" is not a yocto variable, it is the bootloader syntax. Thus this depends on which bootloader you use, but yocto abstracts this. However for all bootloaders I know before boot you can hit "e" to edit the boot line manually.
Quoted 48 lines
Thank you
Quoted 44 lines · JH
Hi Moritz,
I could not find zImage-initramfs:
$ grep zImage tempfileARCH_DEFAULT_KERNELIMAGETYPE="bzImage"
KERNEL_IMAGETYPE="bzImage"
KERNEL_IMAGETYPES="bzImage"
QB_DEFAULT_KERNEL="bzImage"$ grep zImage-initramfs tempfile$ grep INITRAMFS_IMAGE_BUNDLE tempfile# $INITRAMFS_IMAGE_BUNDLE
INITRAMFS_IMAGE_BUNDLE="1"$ grep INITRAMFS_FSTYPES tempfile INITRAMFS_FSTYPES="cpio.gz"I added
PACKAGE_INSTALL+= "initramfs-module-debug" and I added "core-image-minimal-initramfs.bbappend" coppied from yours:$ cat core-image-minimal-initramfs.bbappendPACKAGE_INSTALL += "\ busybox \ base-files \ base-passwd \ bash \ util-linux-lsblk \ vim \ "But I still have troubles to add
INITRAMFS_IMAGE= "core-image-minimal-initramfs" or to run core-image-minimal-initramfs, both had errors:$ MACHINE="solar" DISTRO="solar" bitbake core-image-minimal-initramfsERROR: Nothing PROVIDES 'core-image-minimal-initramfs' core-image-minimal-initramfs was skipped: incompatible with host arm-oe-linux-gnueabi (not in
COMPATIBLE_HOST)
in meta/recipes-core/images/core-image-minimal-initramfs.bb there is the following line:COMPATIBLE_HOST = "(i.86|x86_64).*-linux"
You could try to overwrite it in your .bbappend to the value "*-linux" but I guess there is a reason for this line.
Quoted 440 lines
Quoted 440 lines
$ MACHINE="solar" DISTRO="solar" bitbake solar-imageERROR: Nothing PROVIDES 'core-image-minimal-initramfs' core-image-minimal-initramfs was skipped: incompatible with host arm-oe-linux-gnueabi (not in
COMPATIBLE_HOST)
ERROR: Required build target 'solar-image' has no buildable providers. Missing or unbuildable dependency chain was: ['solar-image', 'virtual/kernel', 'core-image-minimal-initramfs']Sorry, still learning Yocto, what I could be missing?
Quoted 1 line
BOOT_IMAGE=/bzImage root=PARTUUID=71d1d94a-83e8-4895-98eb-35309f58119f
break=premount quiet rootwait rootwait rootfstype=ext4 console=ttyS0,115200 console=tty0
Which did you add kernel boot command for bootargs, bootcmd, etc as above? I could not find
BOOT_IMAGE(I use meta-freescale)Thank you very much.
- jupiter
Quoted 416 lines · Moritz Porst
Forgot to CC Jupiter and the most important thing:
PACKAGE_INSTALL+= "initramfs-module-debug" (To my understanding this
enables the rescue shell)Quoted 410 lines · Moritz Porst
Hey,
The only thing I can add to what I already said is my "core-image-minimal-initramfs.bbappend":
PACKAGE_INSTALL += "\ busybox \ base-files \ base-passwd \ bash \ util-linux-lsblk \ vim \ "Jupiter, are you able to produce your zImage-initramfs now ? If not further do the following:
bitbake <your-image> -e > tempfile
[wait until done, then search]
grep <appropriate search word> tempfilewhere <appropriate search word> may be e.g.: zImage, zImage-initramfs,
INITRAMFS_IMAGE,INITRAMFS_IMAGE_BUNDLE
Especially check that all variables you set are not overwritten somewhere elseBest regards
MoritzQuoted 382 lines · Zoran Stojsavljevic
Moritz,
Thank you very much for this reply. It makes it very clear... What is the current State of Affairs for the topic.
Let us see if there will be the improvement to this topic. I'll document this on one of my private GitHubs. And archive this email.
Zoran
_______Quoted 369 lines · Moritz Porst
Hello Zoran, Jupiter and list
The configuration you sent seems to be correct.
As I already said initramfs seems overly complicated in yocto. the most
important thing to note is that 2 kernel images are created, one is called bzImage (in my case) an the other bzImage-initramfs. However only
the bzImage is written into the rootfs so you have to exchange them manually. (in/boot/bzImage). I did not find a way of including the bundled kernel right away.What you can do is to build core-image-minimal-initramfs and delete the
symbolic link "bzImage", then recreate it and let it point to bzImage-initramfs. However this is rather a hack than a solution.An other mistake I made was to use
IMAGE_INSTALL_appendwhich is ignored. UsePACKAGE_INSTALL_append.Also I found that "break" does not work as a kernel parameter. Use "shell" oder "debug-shell" instead. If you want to try to boot into initramfs you can remove all parameters to the booting line so you either end up in a kernel panic (initramfs doesn't work) or in the rescue shell (initramfs works).
In the end I actually managed to get a working shell, but I often ended
up in initramfs telling me "dropping to shell..." but then freezing.I don't have access to my files right now but I can tell you more on my
setup tomorrow. In case the solution is not included above.Best regards
MoritzQuoted 330 lines · Zoran Stojsavljevic
Hello Moritz,
I need here some help from you. I'll try to reconstruct the parts of the local.conf you are using, so I (and Jupiter) can understand what should we do to also bundle kernel image with initramfs, to end up in Dracut/rescue shell.
Here is what I anticipate after reading several YOCTO @ threads:
IMAGE_FSTYPES_append= " cpio.gz"INITRAMFS_IMAGE= "core-image-minimal-initramfs"INITRAMFS_IMAGE_BUNDLE= "1"
# debug: adds debug boot parameters like 'shell' and 'debug', see# meta/recipes-core/initrdscripts/initramfs-framework/debug for details # Could be removed in more minimal product image PACKAGE_INSTALL += "initramfs-module-debug"Could you, please, review these lines and fix, if something is not correct?
I what I understood, this does the magic, but you could not stop in initramfs shell? Still, this problem is not solved?
Quoted 5 lines
I was following this site: https://wiki.debian.org/InitramfsDebug
Rescue shell (also known as initramfs shell)
Read man initramfs-tools to learn about the break=something kernel parameter (where valid arguments for something are: top, modules, premount, mount, mountroot, bottom, init), which starts a debugQuoted 8 lines
shell.
You can try, for example, break=premount. You can edit/boot/grub/grub.cfg
to add this to the end of the kernel line, or you can do it interactively
from the grub boot menu: "e" to edit, and "b" to boot once you've edited
the kernel line.Now, as my understanding is, you solved this problem actually adding to grub.cfg in command kernel line break=premount, and was able to stop in rescue shell?! Am I correct here?
Thank you,
Zoran
_______Quoted 282 lines · Moritz Porst
Hello,
I think I found the issue. ( see below )On 01.07.19 15:57, Zoran Stojsavljevic wrote:
Hello Moritz,
Too hot here, in Belgrade... Where I am resting for the Time being (actually, this message given to my invisible spying security "angels"
on this list)... :-) Projected +38C degrees today. Too hot for this too old Siberian untouchable bobcat!Luckily it's a rather cold day in germany, thanks that you still take the time to answer !
I started from the core-image-minimal to have a small image and extended it with the features I need, which is e.g. a graphical system.
The console=[...] part in the kernel command line is probably a remnant but my image boots into the GUI. Is this a problem ?Nope, it is not. If you need to do it correctly, you should use bitbake -k core-image-sato build command (my best educated guess). Then, I do not feel comfortable seeing in your kernel command line serial interface, do you agree?
Yes that is true.
YOCTO maintainers, any additional
advices?My bootloader is currently grub, the EFI is AM.
Nope. Eeeeeeeeek. Wrong. Currently, your boot-loader is UEFI AMI. Your
OS (Linux probably, U name it) boot-loader is GRUB2. Let us keep it contained, sane and sober.Sorry but I can't find this info in the EFI.
Could you, please try the following command being root: dmesg | grep MCU. or grep mcu, or grep CPUID or grep cpuid?? Please, post results to this list (to me).
No luck unfortunately (used grep -i)
Could you, also, send to YOCTO list/me attached file:
/boot/microcode.cpioso I can somehow (?) inspect it? ;-)I send it to you directly, so I don't spam the list with a large attachment.
2GB, single channel.
All Cool. E3825 by HW/silicon design could/does NOT support multiple memory channels. ONLY single... But even YOCTO primes (INTEL ones from
this list) are not gonna tell this to you. Not 'cause they are nasty.
They are NOT aware/they are ignorant (with the purpose)! ;-))No, the boot does not stop. Even if I do issue "break=premount" I end up in my graphical interface with the rootfs mounted. This is the
last message in the log: EXT4-fs (sdb2): re-mounted. Opts: (null) The rootfs partition is always 2, so either/dev/sda2or/dev/sdb2(when booting from stick)Yes, from https://pastebin.com/ya7iCtq7, so it is remounted rw, not read only. So, it seems that you have passed dracut phase. and mounted
SD or flash rootfs. So, initramfs is NOT your true problem, is it???The thing is that the boot works but I want an initramfs that can be used for updating (in case the rootfs is broken). However I need to be able to intercept the boot process there because otherwise I can't deploy an update mechanism, that's what I was trying.
Zoran
_______No, the boot does not stop. Even if I do issue "break=premount" I end up
in my graphical interface with the rootfs mounted. This is the last message
in the log: EXT4-fs (sdb2): re-mounted. Opts: (null) The rootfs partition is
always 2, so either/dev/sda2or/dev/sdb2(when booting from stick)So for the issue...
I expected yocto to put the bundled bzImage onto my rootfs. This was not the case. My image directory contains 2x bzImage, one bundled and one unbundled. Apparently yocto puts the >un<bundled image onto my /boot partition and uses it for boot. So of course I couldn't access initramfs in this case. Now I get to the initramfs statement "dropping to shell" if I intentionally boot with wrong rootfs.
Still I don't get the interactive shell.
On the github ostroproject site I found this:# debug: adds debug boot parameters like 'shell' and 'debug', see
# meta/recipes-core/initrdscripts/initramfs-framework/debug for details # Could be removed in more minimal product image. PACKAGE_INSTALL += "initramfs-module-debug"including the module-debug still does not enable me to get an interactive shell.
I was following this site: https://wiki.debian.org/InitramfsDebug
I am aware that yocto is no debian but I expected that kernel parameters (like 'break') would be independent of the distribution.Lastly I do not really need the interactive shell, it is enough if I can deploy a custom init script in the initramfs. Still I think that getting an initramfs shell should be as simple as stating the name of the initramfs image and setting the "
INITRAMFS_DO_BUNDLE" variable.Best regards
MoritzOn Mon, Jul 1, 2019 at 11:20 AM Moritz Porst <[email protected]> wrote:
Hello Zoran,
thanks for your answerOn 28.06.19 14:26, Zoran Stojsavljevic wrote:
INITRAMFS_IMAGE= "core-image-minimal-initramfs"INITRAMFS_IMAGE_BUNDLE= "1"...
You can find the
/var/log/dmesghere: https://pastebin.com/ya7iCtq7ISome hints...
[1] Kernel command line: BOOT_IMAGE=/bzImage root=PARTUUID=71d1d94a-83e8-4895-98eb-35309f58119f break=premount quiet rootwait rootwait rootfstype=ext4 console=ttyS0,115200 console=tty0
input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input7
fbcon: inteldrmfb (fb0) is primary device
Console: switching to colour frame buffer device 128x48 i915 0000:00:02.0: fb0: inteldrmfb frame buffer devicesnd_hda_intel0000:00:1b.0: bound 0000:00:02.0 (opsi915_audio_component_bind_ops[i915])Hmmmmm... You are using console and serial, but full i915 GFX kernel driver is still included in the build???
I started from the core-image-minimal to have a small image and extended it with the features I need, which is e.g. a graphical system. The console=[...] part in the kernel command line is probably a remnant but my image boots into the GUI. Is this a problem ?
[2] efi: EFI v2.31 by American Megatrends
Using AMI BIOS as boot loader FW... OK?! Am I correct?
My bootloader is currently grub, the EFI is AM.
[3] smpboot: CPU0: Intel(R) Atom(TM) CPU E3825 @ 1.33GHz (family:
0x6, model:0x37, stepping:0x9)This is CPUID ID
0x30679, which uses MCU... Which MicroCodeUnit? M0130679xxx (info from AMI BIOS)?Sorry but I can't find this info in the EFI
[4] Using INTEL ATOM BYT E3825 dual core (sans Hyper-threading), implies that you are using
4GB (e820 messages) as single channel (one memory module DDR3 as 4GB)! Am I correct (important)?2GB, single channel.
[5] Dracut phase?!
To my understanding the initramfs should be embedded in
/boot/bzImage.
However since I use an intel platform I also have a/boot/microcode.cpio
which gets loaded via "initrd /microcode.cpio". Removing this line in
grub does not enable me to get an initramfs prompt either (again, using
break as option).You are obviously stopping in boot phase called dracut. Please, try to mount by hand
/dev/sda(whatever)... You should use fdisk -l command, or do ls -al /dev | grep sda to
dig out which partition you need to mount to /tmp dir to see rootfstype=ext4 (HDD/SSD)No, the boot does not stop. Even if I do issue "break=premount" I end up in my graphical interface with the rootfs mounted. This is the last message in the log:
EXT4-fs (sdb2): re-mounted. Opts: (null)
The rootfs partition is always 2, so either/dev/sda2or/dev/sdb2(when booting from stick)_______
Just thinking loud... .. .
Hope this helps (has very little to do with YOCTO build system, BTW) . ;-)
Zoran
_______On Fri, Jun 28, 2019 at 11:22 AM Moritz Porst
<[email protected]> wrote:Hello,
I currently try to deploy a single rootfs update mechanism for my embedded device. I can't boot to initramfs using either "break" or "break=premount" (without quotes...). I tried this in systemd-boot and
grub-efi (always efi boot) but the boot process just continues normally.
If I insert at the same point e.g. "quiet" this argument is recognised.
I boot the .wic image with a separate boot partition from a USB stick.
in local.conf I have set:INITRAMFS_IMAGE= "core-image-minimal-initramfs"INITRAMFS_IMAGE_BUNDLE= "1"In order to reduce complexity I now use the standard core-image-minimal-initramfs without .bbappend. I can confirm (from seeing the task) that bitbake bundled the kernel with the initramfs.
You can find the
/var/log/dmesghere: https://pastebin.com/ya7iCtq7To my understanding the initramfs should be embedded in
/boot/bzImage.
However since I use an intel platform I also have a/boot/microcode.cpio
which gets loaded via "initrd /microcode.cpio". Removing this line in
grub does not enable me to get an initramfs prompt either (again, using
break as option).Did I forget some configuration or do I have to put the break statement
at a very specific position within the "linux ..." boot command ? Do you
know which bitbake variables to check ? (both set in local.conf do not
get overwritten, already checked this). I got the thud branch checked
out in all my meta-layers except for meta-qt which is currently on master branch.Help is much appreciated !
Best regards
Moritz--
_______________________________________________
yocto mailing list
[email protected]
https://lists.yoctoproject.org/listinfo/yocto
Hello Scott (Rifenbark),
Could you, please, document somewhere (YOCTO-Mega-Manual for example) this topic (booting to YOCTO initramfs rescue shell), as we are discussing it?
It would be very beneficial to YOCTO WWW audience, don't you agree?
Thank you,
Zoran
_______
Quoted 512 lines · Moritz Porst
Hey
Quoted 7 lines · JH
Quoted 1 line
BOOT_IMAGE=/bzImage root=PARTUUID=71d1d94a-83e8-4895-98eb-35309f58119f
break=premount quiet rootwait rootwait rootfstype=ext4 console=ttyS0,115200 console=tty0
Which file did you add kernel boot command for bootargs, bootcmd, etc?
I use meta-freescale, but I could not find
BOOT_IMAGEis defined.Ways I know to add boot arguments:
If you use .wic image via --append in the .wks file Otherwise in your machine config via the variable "APPEND", e.g. APPEND += "quiet shell"
the "BOOT_IMAGE" is not a yocto variable, it is the bootloader syntax. Thus this depends on which bootloader you use, but yocto abstracts this. However for all bootloaders I know before boot you can hit "e" to edit the boot line manually.Quoted 48 lines
Thank you
Quoted 44 lines · JH
Hi Moritz,
I could not find zImage-initramfs:
$ grep zImage tempfileARCH_DEFAULT_KERNELIMAGETYPE="bzImage"
KERNEL_IMAGETYPE="bzImage"
KERNEL_IMAGETYPES="bzImage"
QB_DEFAULT_KERNEL="bzImage"$ grep zImage-initramfs tempfile$ grep INITRAMFS_IMAGE_BUNDLE tempfile# $INITRAMFS_IMAGE_BUNDLE
INITRAMFS_IMAGE_BUNDLE="1"$ grep INITRAMFS_FSTYPES tempfile INITRAMFS_FSTYPES="cpio.gz"I added
PACKAGE_INSTALL+= "initramfs-module-debug" and I added "core-image-minimal-initramfs.bbappend" coppied from yours:$ cat core-image-minimal-initramfs.bbappendPACKAGE_INSTALL += "\ busybox \ base-files \ base-passwd \ bash \ util-linux-lsblk \ vim \ "But I still have troubles to add
INITRAMFS_IMAGE= "core-image-minimal-initramfs" or to run core-image-minimal-initramfs, both had errors:$ MACHINE="solar" DISTRO="solar" bitbake core-image-minimal-initramfsERROR: Nothing PROVIDES 'core-image-minimal-initramfs' core-image-minimal-initramfs was skipped: incompatible with host arm-oe-linux-gnueabi (not in
COMPATIBLE_HOST)in meta/recipes-core/images/core-image-minimal-initramfs.bb there is the following line:
COMPATIBLE_HOST= "(i.86|x86_64).*-linux"
You could try to overwrite it in your .bbappend to the value "*-linux" but I guess there is a reason for this line.Quoted 440 lines
Quoted 440 lines
$ MACHINE="solar" DISTRO="solar" bitbake solar-imageERROR: Nothing PROVIDES 'core-image-minimal-initramfs' core-image-minimal-initramfs was skipped: incompatible with host arm-oe-linux-gnueabi (not in
COMPATIBLE_HOST)
ERROR: Required build target 'solar-image' has no buildable providers. Missing or unbuildable dependency chain was: ['solar-image', 'virtual/kernel', 'core-image-minimal-initramfs']Sorry, still learning Yocto, what I could be missing?
Quoted 1 line
BOOT_IMAGE=/bzImage root=PARTUUID=71d1d94a-83e8-4895-98eb-35309f58119f
break=premount quiet rootwait rootwait rootfstype=ext4 console=ttyS0,115200 console=tty0
Which did you add kernel boot command for bootargs, bootcmd, etc as above? I could not find
BOOT_IMAGE(I use meta-freescale)Thank you very much.
- jupiter
Quoted 416 lines · Moritz Porst
Forgot to CC Jupiter and the most important thing:
PACKAGE_INSTALL+= "initramfs-module-debug" (To my understanding this
enables the rescue shell)Quoted 410 lines · Moritz Porst
Hey,
The only thing I can add to what I already said is my "core-image-minimal-initramfs.bbappend":
PACKAGE_INSTALL += "\ busybox \ base-files \ base-passwd \ bash \ util-linux-lsblk \ vim \ "Jupiter, are you able to produce your zImage-initramfs now ? If not further do the following:
bitbake <your-image> -e > tempfile
[wait until done, then search]
grep <appropriate search word> tempfilewhere <appropriate search word> may be e.g.: zImage, zImage-initramfs,
INITRAMFS_IMAGE,INITRAMFS_IMAGE_BUNDLE
Especially check that all variables you set are not overwritten somewhere elseBest regards
MoritzQuoted 382 lines · Zoran Stojsavljevic
Moritz,
Thank you very much for this reply. It makes it very clear... What is the current State of Affairs for the topic.
Let us see if there will be the improvement to this topic. I'll document this on one of my private GitHubs. And archive this email.
Zoran
_______Quoted 369 lines · Moritz Porst
Hello Zoran, Jupiter and list
The configuration you sent seems to be correct.
As I already said initramfs seems overly complicated in yocto. the most
important thing to note is that 2 kernel images are created, one is called bzImage (in my case) an the other bzImage-initramfs. However only
the bzImage is written into the rootfs so you have to exchange them manually. (in/boot/bzImage). I did not find a way of including the bundled kernel right away.What you can do is to build core-image-minimal-initramfs and delete the
symbolic link "bzImage", then recreate it and let it point to bzImage-initramfs. However this is rather a hack than a solution.An other mistake I made was to use
IMAGE_INSTALL_appendwhich is ignored. UsePACKAGE_INSTALL_append.Also I found that "break" does not work as a kernel parameter. Use "shell" oder "debug-shell" instead. If you want to try to boot into initramfs you can remove all parameters to the booting line so you either end up in a kernel panic (initramfs doesn't work) or in the rescue shell (initramfs works).
In the end I actually managed to get a working shell, but I often ended
up in initramfs telling me "dropping to shell..." but then freezing.I don't have access to my files right now but I can tell you more on my
setup tomorrow. In case the solution is not included above.Best regards
MoritzQuoted 330 lines · Zoran Stojsavljevic
Hello Moritz,
I need here some help from you. I'll try to reconstruct the parts of the local.conf you are using, so I (and Jupiter) can understand what should we do to also bundle kernel image with initramfs, to end up in Dracut/rescue shell.
Here is what I anticipate after reading several YOCTO @ threads:
IMAGE_FSTYPES_append= " cpio.gz"INITRAMFS_IMAGE= "core-image-minimal-initramfs"INITRAMFS_IMAGE_BUNDLE= "1"
# debug: adds debug boot parameters like 'shell' and 'debug', see# meta/recipes-core/initrdscripts/initramfs-framework/debug for details # Could be removed in more minimal product image PACKAGE_INSTALL += "initramfs-module-debug"Could you, please, review these lines and fix, if something is not correct?
I what I understood, this does the magic, but you could not stop in initramfs shell? Still, this problem is not solved?
Quoted 5 lines
I was following this site: https://wiki.debian.org/InitramfsDebug
Rescue shell (also known as initramfs shell)
Read man initramfs-tools to learn about the break=something kernel parameter (where valid arguments for something are: top, modules, premount, mount, mountroot, bottom, init), which starts a debugQuoted 8 lines
shell.
You can try, for example, break=premount. You can edit/boot/grub/grub.cfg
to add this to the end of the kernel line, or you can do it interactively
from the grub boot menu: "e" to edit, and "b" to boot once you've edited
the kernel line.Now, as my understanding is, you solved this problem actually adding to grub.cfg in command kernel line break=premount, and was able to stop in rescue shell?! Am I correct here?
Thank you,
Zoran
_______Quoted 282 lines · Moritz Porst
Hello,
I think I found the issue. ( see below )On 01.07.19 15:57, Zoran Stojsavljevic wrote:
Hello Moritz,
Too hot here, in Belgrade... Where I am resting for the Time being (actually, this message given to my invisible spying security "angels"
on this list)... :-) Projected +38C degrees today. Too hot for this too old Siberian untouchable bobcat!Luckily it's a rather cold day in germany, thanks that you still take the time to answer !
I started from the core-image-minimal to have a small image and extended it with the features I need, which is e.g. a graphical system.
The console=[...] part in the kernel command line is probably a remnant but my image boots into the GUI. Is this a problem ?Nope, it is not. If you need to do it correctly, you should use bitbake -k core-image-sato build command (my best educated guess). Then, I do not feel comfortable seeing in your kernel command line serial interface, do you agree?
Yes that is true.
YOCTO maintainers, any additional
advices?My bootloader is currently grub, the EFI is AM.
Nope. Eeeeeeeeek. Wrong. Currently, your boot-loader is UEFI AMI. Your
OS (Linux probably, U name it) boot-loader is GRUB2. Let us keep it contained, sane and sober.Sorry but I can't find this info in the EFI.
Could you, please try the following command being root: dmesg | grep MCU. or grep mcu, or grep CPUID or grep cpuid?? Please, post results to this list (to me).
No luck unfortunately (used grep -i)
Could you, also, send to YOCTO list/me attached file:
/boot/microcode.cpioso I can somehow (?) inspect it? ;-)I send it to you directly, so I don't spam the list with a large attachment.
2GB, single channel.
All Cool. E3825 by HW/silicon design could/does NOT support multiple memory channels. ONLY single... But even YOCTO primes (INTEL ones from
this list) are not gonna tell this to you. Not 'cause they are nasty.
They are NOT aware/they are ignorant (with the purpose)! ;-))No, the boot does not stop. Even if I do issue "break=premount" I end up in my graphical interface with the rootfs mounted. This is the
last message in the log: EXT4-fs (sdb2): re-mounted. Opts: (null) The rootfs partition is always 2, so either/dev/sda2or/dev/sdb2(when booting from stick)Yes, from https://pastebin.com/ya7iCtq7, so it is remounted rw, not read only. So, it seems that you have passed dracut phase. and mounted
SD or flash rootfs. So, initramfs is NOT your true problem, is it???The thing is that the boot works but I want an initramfs that can be used for updating (in case the rootfs is broken). However I need to be able to intercept the boot process there because otherwise I can't deploy an update mechanism, that's what I was trying.
Zoran
_______No, the boot does not stop. Even if I do issue "break=premount" I end up
in my graphical interface with the rootfs mounted. This is the last message
in the log: EXT4-fs (sdb2): re-mounted. Opts: (null) The rootfs partition is
always 2, so either/dev/sda2or/dev/sdb2(when booting from stick)So for the issue...
I expected yocto to put the bundled bzImage onto my rootfs. This was not the case. My image directory contains 2x bzImage, one bundled and one unbundled. Apparently yocto puts the >un<bundled image onto my /boot partition and uses it for boot. So of course I couldn't access initramfs in this case. Now I get to the initramfs statement "dropping to shell" if I intentionally boot with wrong rootfs.
Still I don't get the interactive shell.
On the github ostroproject site I found this:# debug: adds debug boot parameters like 'shell' and 'debug', see
# meta/recipes-core/initrdscripts/initramfs-framework/debug for details # Could be removed in more minimal product image. PACKAGE_INSTALL += "initramfs-module-debug"including the module-debug still does not enable me to get an interactive shell.
I was following this site: https://wiki.debian.org/InitramfsDebug
I am aware that yocto is no debian but I expected that kernel parameters (like 'break') would be independent of the distribution.Lastly I do not really need the interactive shell, it is enough if I can deploy a custom init script in the initramfs. Still I think that getting an initramfs shell should be as simple as stating the name of the initramfs image and setting the "
INITRAMFS_DO_BUNDLE" variable.Best regards
MoritzOn Mon, Jul 1, 2019 at 11:20 AM Moritz Porst <[email protected]> wrote:
Hello Zoran,
thanks for your answerOn 28.06.19 14:26, Zoran Stojsavljevic wrote:
INITRAMFS_IMAGE= "core-image-minimal-initramfs"INITRAMFS_IMAGE_BUNDLE= "1"...
You can find the
/var/log/dmesghere: https://pastebin.com/ya7iCtq7ISome hints...
[1] Kernel command line: BOOT_IMAGE=/bzImage root=PARTUUID=71d1d94a-83e8-4895-98eb-35309f58119f break=premount quiet rootwait rootwait rootfstype=ext4 console=ttyS0,115200 console=tty0
input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input7
fbcon: inteldrmfb (fb0) is primary device
Console: switching to colour frame buffer device 128x48 i915 0000:00:02.0: fb0: inteldrmfb frame buffer devicesnd_hda_intel0000:00:1b.0: bound 0000:00:02.0 (opsi915_audio_component_bind_ops[i915])Hmmmmm... You are using console and serial, but full i915 GFX kernel driver is still included in the build???
I started from the core-image-minimal to have a small image and extended it with the features I need, which is e.g. a graphical system. The console=[...] part in the kernel command line is probably a remnant but my image boots into the GUI. Is this a problem ?
[2] efi: EFI v2.31 by American Megatrends
Using AMI BIOS as boot loader FW... OK?! Am I correct?
My bootloader is currently grub, the EFI is AM.
[3] smpboot: CPU0: Intel(R) Atom(TM) CPU E3825 @ 1.33GHz (family:
0x6, model:0x37, stepping:0x9)This is CPUID ID
0x30679, which uses MCU... Which MicroCodeUnit? M0130679xxx (info from AMI BIOS)?Sorry but I can't find this info in the EFI
[4] Using INTEL ATOM BYT E3825 dual core (sans Hyper-threading), implies that you are using
4GB (e820 messages) as single channel (one memory module DDR3 as 4GB)! Am I correct (important)?2GB, single channel.
[5] Dracut phase?!
To my understanding the initramfs should be embedded in
/boot/bzImage.
However since I use an intel platform I also have a/boot/microcode.cpio
which gets loaded via "initrd /microcode.cpio". Removing this line in
grub does not enable me to get an initramfs prompt either (again, using
break as option).You are obviously stopping in boot phase called dracut. Please, try to mount by hand
/dev/sda(whatever)... You should use fdisk -l command, or do ls -al /dev | grep sda to
dig out which partition you need to mount to /tmp dir to see rootfstype=ext4 (HDD/SSD)No, the boot does not stop. Even if I do issue "break=premount" I end up in my graphical interface with the rootfs mounted. This is the last message in the log:
EXT4-fs (sdb2): re-mounted. Opts: (null)
The rootfs partition is always 2, so either/dev/sda2or/dev/sdb2(when booting from stick)_______
Just thinking loud... .. .
Hope this helps (has very little to do with YOCTO build system, BTW) . ;-)
Zoran
_______On Fri, Jun 28, 2019 at 11:22 AM Moritz Porst
<[email protected]> wrote:Hello,
I currently try to deploy a single rootfs update mechanism for my embedded device. I can't boot to initramfs using either "break" or "break=premount" (without quotes...). I tried this in systemd-boot and
grub-efi (always efi boot) but the boot process just continues normally.
If I insert at the same point e.g. "quiet" this argument is recognised.
I boot the .wic image with a separate boot partition from a USB stick.
in local.conf I have set:INITRAMFS_IMAGE= "core-image-minimal-initramfs"INITRAMFS_IMAGE_BUNDLE= "1"In order to reduce complexity I now use the standard core-image-minimal-initramfs without .bbappend. I can confirm (from seeing the task) that bitbake bundled the kernel with the initramfs.
You can find the
/var/log/dmesghere: https://pastebin.com/ya7iCtq7To my understanding the initramfs should be embedded in
/boot/bzImage.
However since I use an intel platform I also have a/boot/microcode.cpio
which gets loaded via "initrd /microcode.cpio". Removing this line in
grub does not enable me to get an initramfs prompt either (again, using
break as option).Did I forget some configuration or do I have to put the break statement
at a very specific position within the "linux ..." boot command ? Do you
know which bitbake variables to check ? (both set in local.conf do not
get overwritten, already checked this). I got the thud branch checked
out in all my meta-layers except for meta-qt which is currently on master branch.Help is much appreciated !
Best regards
Moritz--
_______________________________________________
yocto mailing list
[email protected]
https://lists.yoctoproject.org/listinfo/yocto
Hi Moritz,
Quoted 4 lines · Moritz Porst
Hey
Quoted 1 line · JH
Quoted 1 line
BOOT_IMAGE=/bzImage root=PARTUUID=71d1d94a-83e8-4895-98eb-35309f58119f
Quoted 8 lines
Quoted 6 lines
break=premount quiet rootwait rootwait rootfstype=ext4 console=ttyS0,115200 console=tty0
Which file did you add kernel boot command for bootargs, bootcmd, etc?
I use meta-freescale, but I could not find
BOOT_IMAGEis defined.Ways I know to add boot arguments:
If you use .wic image via --append in the .wks file
Right, I use .wic image.
Quoted 2 lines
Otherwise in your machine config via the variable "APPEND", e.g. APPEND += "quiet shell"
OK, I added APPEND += "quiet shell" to my machine config file solar.conf.
Quoted 4 lines
the "
BOOT_IMAGE" is not a yocto variable, it is the bootloader syntax. Thus this depends on which bootloader you use, but yocto abstracts this. However for all bootloaders I know before boot you can hit "e" to edit the boot line manually.
I use u-boot, I am currently running zImage-initramfs built from OpenWrt defined kernel boot arguement bootargs, bootcmd, console, etc. Although I can edit the u-boot kernel arguments during bootload running on imx6 ram, I really want to configure those arguments in Yocto to build a Yoctor zImage-initramfs.
I guess there must be some ways to configure it for zImage-initramfs, but the meta-freescale/wic/imx-uboot-bootpart.wks and other wks files are all used for creating SD card image which I guess that cannot be used to build an initramfs image for running on RAM, but correct me I could be wrong.
Here are kernel arguments when I run zImage-initramfs on imx6 ram:
....
printenv
baudrate=115200
board_name=ULZ-EVK
board_rev=14X14
bootargs=console=ttymxc0,115200 earlycon init=/init ......
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
But I still have troubles to add
INITRAMFS_IMAGE= "core-image-minimal-initramfs" or to run core-image-minimal-initramfs, both had errors:$ MACHINE="solar" DISTRO="solar" bitbake core-image-minimal-initramfs
Quoted 8 lines
Quoted 3 lines
Quoted 3 lines
ERROR: Nothing PROVIDES 'core-image-minimal-initramfs' core-image-minimal-initramfs was skipped: incompatible with host arm-oe-linux-gnueabi (not in
COMPATIBLE_HOST)in meta/recipes-core/images/core-image-minimal-initramfs.bb there is the following line:
COMPATIBLE_HOST= "(i.86|x86_64).*-linux"
You could try to overwrite it in your .bbappend to the value "*-linux" but I guess there is a reason for this line.
Is the following core-image-minimal-initramfs.bbappend correct? I still got errors to build core-image-minimal-initramfs, I must misplace things here:
$ cat core-image-minimal-initramfs.bbappend PACKAGE_INSTALL += "\ busybox \ base-files \ base-passwd \ bash \ util-linux-lsblk \ vim \ "
COMPATIBLE_HOST = "(arm|arm-oe-linux-gnueabi).*-linux"
$ MACHINE="solar" DISTRO="solar" bitbake core-image-minimal-initramfs ERROR: Nothing RPROVIDES 'initramfs-module-install' initramfs-module-install was skipped: incompatible with host arm-oe-linux-gnueabi (not in COMPATIBLE_HOST)
Thank you very much.
- jupiter
Quoted 29 lines
Quoted 29 lines
Quoted 29 lines
$ MACHINE="solar" DISTRO="solar" bitbake solar-imageERROR: Nothing PROVIDES 'core-image-minimal-initramfs' core-image-minimal-initramfs was skipped: incompatible with host arm-oe-linux-gnueabi (not in
COMPATIBLE_HOST)
ERROR: Required build target 'solar-image' has no buildable providers. Missing or unbuildable dependency chain was: ['solar-image', 'virtual/kernel', 'core-image-minimal-initramfs']Sorry, still learning Yocto, what I could be missing?
Quoted 1 line
BOOT_IMAGE=/bzImage root=PARTUUID=71d1d94a-83e8-4895-98eb-35309f58119f
break=premount quiet rootwait rootwait rootfstype=ext4 console=ttyS0,115200 console=tty0
Which did you add kernel boot command for bootargs, bootcmd, etc as above? I could not find
BOOT_IMAGE(I use meta-freescale)Thank you very much.
- jupiter
Quoted 5 lines · Moritz Porst
Forgot to CC Jupiter and the most important thing:
PACKAGE_INSTALL+= "initramfs-module-debug" (To my understanding this
enables the rescue shell)
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines · Moritz Porst
Quoted 6 lines
Hey,
The only thing I can add to what I already said is my "core-image-minimal-initramfs.bbappend":
PACKAGE_INSTALL += "\ busybox \printenv
baudrate=115200
board_name=ULZ-EVK
board_rev=14X14> base-files \
Quoted 421 lines
Quoted 420 lines
Quoted 420 lines
Quoted 420 lines
Quoted 420 lines
base-passwd \ bash \ util-linux-lsblk \ vim \ "Jupiter, are you able to produce your zImage-initramfs now ? If not further do the following:
bitbake <your-image> -e > tempfile
[wait until done, then search]
grep <appropriate search word> tempfilewhere <appropriate search word> may be e.g.: zImage, zImage-initramfs,
INITRAMFS_IMAGE,INITRAMFS_IMAGE_BUNDLE
Especially check that all variables you set are not overwritten somewhere elseBest regards
MoritzQuoted 399 lines · Zoran Stojsavljevic
Moritz,
Thank you very much for this reply. It makes it very clear... What is the current State of Affairs for the topic.
Let us see if there will be the improvement to this topic. I'll document this on one of my private GitHubs. And archive this email.
Zoran
_______Quoted 386 lines · Moritz Porst
Hello Zoran, Jupiter and list
The configuration you sent seems to be correct.
As I already said initramfs seems overly complicated in yocto. the most
important thing to note is that 2 kernel images are created, one is called bzImage (in my case) an the other bzImage-initramfs. However only
the bzImage is written into the rootfs so you have to exchange them manually. (in/boot/bzImage). I did not find a way of including the bundled kernel right away.What you can do is to build core-image-minimal-initramfs and delete the
symbolic link "bzImage", then recreate it and let it point to bzImage-initramfs. However this is rather a hack than a solution.An other mistake I made was to use
IMAGE_INSTALL_appendwhich is ignored. UsePACKAGE_INSTALL_append.Also I found that "break" does not work as a kernel parameter. Use "shell" oder "debug-shell" instead. If you want to try to boot into initramfs you can remove all parameters to the booting line so you either end up in a kernel panic (initramfs doesn't work) or in the rescue shell (initramfs works).
In the end I actually managed to get a working shell, but I often ended
up in initramfs telling me "dropping to shell..." but then freezing.I don't have access to my files right now but I can tell you more on my
setup tomorrow. In case the solution is not included above.Best regards
MoritzQuoted 347 lines · Zoran Stojsavljevic
Hello Moritz,
I need here some help from you. I'll try to reconstruct the parts of
the local.conf you are using, so I (and Jupiter) can understand what
should we do to also bundle kernel image with initramfs, to end up in
Dracut/rescue shell.Here is what I anticipate after reading several YOCTO @ threads:
IMAGE_FSTYPES_append= " cpio.gz"INITRAMFS_IMAGE= "core-image-minimal-initramfs"INITRAMFS_IMAGE_BUNDLE= "1"
# debug: adds debug boot parameters like 'shell' and 'debug', see# meta/recipes-core/initrdscripts/initramfs-framework/debug for details # Could be removed in more minimal product image PACKAGE_INSTALL += "initramfs-module-debug"Could you, please, review these lines and fix, if something is not correct?
I what I understood, this does the magic, but you could not stop in initramfs shell? Still, this problem is not solved?
Quoted 5 lines
I was following this site: https://wiki.debian.org/InitramfsDebug
Rescue shell (also known as initramfs shell)
Read man initramfs-tools to learn about the break=something kernel parameter (where valid arguments for something are: top, modules, premount, mount, mountroot, bottom, init), which starts a debugQuoted 8 lines
shell.
You can try, for example, break=premount. You can edit/boot/grub/grub.cfg
to add this to the end of the kernel line, or you can do it interactively
from the grub boot menu: "e" to edit, and "b" to boot once you've edited
the kernel line.Now, as my understanding is, you solved this problem actually adding
to grub.cfg in command kernel line break=premount, and was able to stop in rescue shell?! Am I correct here?Thank you,
Zoran
_______Quoted 295 lines · Moritz Porst
Hello,
I think I found the issue. ( see below )On 01.07.19 15:57, Zoran Stojsavljevic wrote:
Hello Moritz,
Too hot here, in Belgrade... Where I am resting for the Time being (actually, this message given to my invisible spying security "angels"
on this list)... :-) Projected +38C degrees today. Too hot for this
too old Siberian untouchable bobcat!Luckily it's a rather cold day in germany, thanks that you still take the time to answer !
I started from the core-image-minimal to have a small image and extended it with the features I need, which is e.g. a graphical system.
The console=[...] part in the kernel command line is probably a remnant but my image boots into the GUI. Is this a problem ?Nope, it is not. If you need to do it correctly, you should use bitbake -k core-image-sato build command (my best educated guess). Then, I do not feel comfortable seeing in your kernel command line serial interface, do you agree?
Yes that is true.
YOCTO maintainers, any additional
advices?My bootloader is currently grub, the EFI is AM.
Nope. Eeeeeeeeek. Wrong. Currently, your boot-loader is UEFI AMI. Your
OS (Linux probably, U name it) boot-loader is GRUB2. Let us keep it
contained, sane and sober.Sorry but I can't find this info in the EFI.
Could you, please try the following command being root: dmesg | grep
MCU. or grep mcu, or grep CPUID or grep cpuid?? Please, post results
to this list (to me).No luck unfortunately (used grep -i)
Could you, also, send to YOCTO list/me attached file:
/boot/microcode.cpioso I can somehow (?) inspect it? ;-)I send it to you directly, so I don't spam the list with a large attachment.
2GB, single channel.
All Cool. E3825 by HW/silicon design could/does NOT support multiple
memory channels. ONLY single... But even YOCTO primes (INTEL ones from
this list) are not gonna tell this to you. Not 'cause they are nasty.
They are NOT aware/they are ignorant (with the purpose)! ;-))No, the boot does not stop. Even if I do issue "break=premount" I end up in my graphical interface with the rootfs mounted. This is the
last message in the log: EXT4-fs (sdb2): re-mounted. Opts: (null) The rootfs partition is always 2, so either/dev/sda2or/dev/sdb2(when booting from stick)Yes, from https://pastebin.com/ya7iCtq7, so it is remounted rw, not
read only. So, it seems that you have passed dracut phase. and mounted
SD or flash rootfs. So, initramfs is NOT your true problem, is it???The thing is that the boot works but I want an initramfs that can be used for updating (in case the rootfs is broken). However I need to be able to intercept the boot process there because otherwise I can't deploy an update mechanism, that's what I was trying.
Zoran
_______No, the boot does not stop. Even if I do issue "break=premount" I end up
in my graphical interface with the rootfs mounted. This is the last message
in the log: EXT4-fs (sdb2): re-mounted. Opts: (null) The rootfs partition is
always 2, so either/dev/sda2or/dev/sdb2(when booting from stick)So for the issue...
I expected yocto to put the bundled bzImage onto my rootfs. This was not the case. My image directory contains 2x bzImage, one bundled and one unbundled. Apparently yocto puts the >un<bundled image onto my /boot partition and uses it for boot. So of course I couldn't access initramfs in this case. Now I get to the initramfs statement "dropping to shell" if I intentionally boot with wrong rootfs.
Still I don't get the interactive shell.
On the github ostroproject site I found this:# debug: adds debug boot parameters like 'shell' and 'debug', see
# meta/recipes-core/initrdscripts/initramfs-framework/debug for details # Could be removed in more minimal product image. PACKAGE_INSTALL += "initramfs-module-debug"including the module-debug still does not enable me to get an interactive shell.
I was following this site: https://wiki.debian.org/InitramfsDebug
I am aware that yocto is no debian but I expected that kernel parameters (like 'break') would be independent of the distribution.Lastly I do not really need the interactive shell, it is enough if I can deploy a custom init script in the initramfs. Still I think that getting an initramfs shell should be as simple as stating the name of the initramfs image and setting the "
INITRAMFS_DO_BUNDLE" variable.Best regards
MoritzOn Mon, Jul 1, 2019 at 11:20 AM Moritz Porst <[email protected]> wrote:
Hello Zoran,
thanks for your answerOn 28.06.19 14:26, Zoran Stojsavljevic wrote:
INITRAMFS_IMAGE= "core-image-minimal-initramfs"INITRAMFS_IMAGE_BUNDLE= "1"...
You can find the
/var/log/dmesghere:
https://pastebin.com/ya7iCtq7ISome hints...
[1] Kernel command line: BOOT_IMAGE=/bzImage root=PARTUUID=71d1d94a-83e8-4895-98eb-35309f58119f break=premount quiet rootwait rootwait rootfstype=ext4 console=ttyS0,115200 console=tty0
input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input7
fbcon: inteldrmfb (fb0) is primary device
Console: switching to colour frame buffer device 128x48 i915 0000:00:02.0: fb0: inteldrmfb frame buffer devicesnd_hda_intel0000:00:1b.0: bound 0000:00:02.0 (opsi915_audio_component_bind_ops[i915])Hmmmmm... You are using console and serial, but full i915 GFX kernel driver is still included in the build???
I started from the core-image-minimal to have a small image and extended it with the features I need, which is e.g. a graphical system. The console=[...] part in the kernel command line is probably a remnant but my image boots into the GUI. Is this a problem ?
[2] efi: EFI v2.31 by American Megatrends
Using AMI BIOS as boot loader FW... OK?! Am I correct?
My bootloader is currently grub, the EFI is AM.
[3] smpboot: CPU0: Intel(R) Atom(TM) CPU E3825 @ 1.33GHz (family:
0x6, model:0x37, stepping:0x9)This is CPUID ID
0x30679, which uses MCU... Which MicroCodeUnit? M0130679xxx (info from AMI BIOS)?Sorry but I can't find this info in the EFI
[4] Using INTEL ATOM BYT E3825 dual core (sans Hyper-threading), implies that you are using
4GB (e820 messages) as single channel (one memory module DDR3 as 4GB)! Am I correct (important)?2GB, single channel.
[5] Dracut phase?!
To my understanding the initramfs should be embedded in
/boot/bzImage.
However since I use an intel platform I also have a/boot/microcode.cpio
which gets loaded via "initrd /microcode.cpio". Removing this line in
grub does not enable me to get an initramfs prompt either (again, using
break as option).You are obviously stopping in boot phase called dracut. Please, try to mount by hand
/dev/sda(whatever)... You should use fdisk -l command, or do ls -al /dev | grep sda to
dig out which partition you need to mount to /tmp dir to see rootfstype=ext4 (HDD/SSD)No, the boot does not stop. Even if I do issue "break=premount" I end up in my graphical interface with the rootfs mounted. This is the last message in the log:
EXT4-fs (sdb2): re-mounted. Opts: (null)
The rootfs partition is always 2, so either/dev/sda2or/dev/sdb2(when booting from stick)_______
Just thinking loud... .. .
Hope this helps (has very little to do with YOCTO build system, BTW) . ;-)
Zoran
_______On Fri, Jun 28, 2019 at 11:22 AM Moritz Porst
<[email protected]> wrote:Hello,
I currently try to deploy a single rootfs update mechanism for my embedded device. I can't boot to initramfs using either "break" or "break=premount" (without quotes...). I tried this in systemd-boot and
grub-efi (always efi boot) but the boot process just continues normally.
If I insert at the same point e.g. "quiet" this argument is recognised.
I boot the .wic image with a separate boot partition from a USB stick.
in local.conf I have set:INITRAMFS_IMAGE= "core-image-minimal-initramfs"INITRAMFS_IMAGE_BUNDLE= "1"In order to reduce complexity I now use the standard core-image-minimal-initramfs without .bbappend. I can confirm (from
seeing the task) that bitbake bundled the kernel with the initramfs.You can find the
/var/log/dmesghere:
https://pastebin.com/ya7iCtq7To my understanding the initramfs should be embedded in
/boot/bzImage.
However since I use an intel platform I also have a/boot/microcode.cpio
which gets loaded via "initrd /microcode.cpio". Removing this line in
grub does not enable me to get an initramfs prompt either (again, using
break as option).Did I forget some configuration or do I have to put the break statement
at a very specific position within the "linux ..." boot command ? Do you
know which bitbake variables to check ? (both set in local.conf do not
get overwritten, already checked this). I got the thud branch checked
out in all my meta-layers except for meta-qt which is currently on master branch.Help is much appreciated !
Best regards
Moritz--
_______________________________________________
yocto mailing list
[email protected]
https://lists.yoctoproject.org/listinfo/yocto
Hey Jupiter,
you seem to confuse a few concepts, at least as far as I understand
Am 12.07.2019 um 14:53 schrieb JH:
Quoted 12 lines
Hi Moritz,
Quoted 9 lines · Moritz Porst
Hey
Quoted 6 lines · JH
Quoted 1 line
BOOT_IMAGE=/bzImage root=PARTUUID=71d1d94a-83e8-4895-98eb-35309f58119f
break=premount quiet rootwait rootwait rootfstype=ext4 console=ttyS0,115200 console=tty0
Which file did you add kernel boot command for bootargs, bootcmd, etc?
Quoted 8 lines
Quoted 3 lines
Quoted 1 line
I use meta-freescale, but I could not find
BOOT_IMAGEis defined.Ways I know to add boot arguments:
If you use .wic image via --append in the .wks fileRight, I use .wic image.
Quoted 2 lines
Otherwise in your machine config via the variable "APPEND", e.g. APPEND += "quiet shell"
OK, I added APPEND += "quiet shell" to my machine config file solar.conf.
First of all this was only an example. If you don't need these arguments don't add them. However you can check on boot if the arguments "quiet shell" were actually appended to your kernel arguments.
If I use the .wic image, APPEND is ignored. You need to write your own kickstart file for this and include --append option. This usually means copy what you need from existing files (check license compliance) and add what you need. See the yocto manual on kickstart files:
https://www.yoctoproject.org/docs/latest/mega-manual/mega-manual.html#ref-kickstart
Quoted 10 lines
Quoted 5 lines
the "
BOOT_IMAGE" is not a yocto variable, it is the bootloader syntax. Thus this depends on which bootloader you use, but yocto abstracts this. However for all bootloaders I know before boot you can hit "e" to edit the boot line manually.I use u-boot, I am currently running zImage-initramfs built from OpenWrt defined kernel boot arguement bootargs, bootcmd, console, etc. Although I can edit the u-boot kernel arguments during bootload running on imx6 ram, I really want to configure those arguments in Yocto to build a Yoctor zImage-initramfs.
Wait, this makes no sense to me. I take my core-image-minimal-<machine>.wic and deploy it on my machine. On boot, having the correct (bundled) kernel in /boot directory, I then boot through initramfs into rootfs or - using "shell" or "shell-debug" kernel parameter - boot into initramfs.
However these are the parameters to the kernel ON BOOT, not to build. The way you talk it seems that you expect these arguments to build you an initramfs inside yocto. This is not the case.
Quoted 6 lines
I guess there must be some ways to configure it for zImage-initramfs, but the meta-freescale/wic/imx-uboot-bootpart.wks and other wks files are all used for creating SD card image which I guess that cannot be used to build an initramfs image for running on RAM, but correct me I could be wrong.
The .wks file defines how the .wic image is partitioned on the disk. Your initramfs is your "initial ram filesystem", it is not partitioned since it gets loaded entirely into ram.
Quoted 27 lines
Here are kernel arguments when I run zImage-initramfs on imx6 ram:
....
printenv
baudrate=115200
board_name=ULZ-EVK
board_rev=14X14
bootargs=console=ttymxc0,115200 earlycon init=/init ......Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
But I still have troubles to add
INITRAMFS_IMAGE= "core-image-minimal-initramfs" or to run core-image-minimal-initramfs, both had errors:$ MACHINE="solar" DISTRO="solar" bitbake core-image-minimal-initramfsQuoted 8 lines
Quoted 3 lines
Quoted 3 lines
ERROR: Nothing PROVIDES 'core-image-minimal-initramfs' core-image-minimal-initramfs was skipped: incompatible with host arm-oe-linux-gnueabi (not in
COMPATIBLE_HOST)in meta/recipes-core/images/core-image-minimal-initramfs.bb there is the following line:
COMPATIBLE_HOST= "(i.86|x86_64).*-linux"
You could try to overwrite it in your .bbappend to the value "*-linux" but I guess there is a reason for this line.Is the following core-image-minimal-initramfs.bbappend correct? I still got errors to build core-image-minimal-initramfs, I must misplace things here:
Quoted 9 lines
$ cat core-image-minimal-initramfs.bbappend PACKAGE_INSTALL += "\ busybox \ base-files \ base-passwd \ bash \ util-linux-lsblk \ vim \ "
Note: bash, util-linux-lsblk and vim are just my preferences, you can remove them.
Quoted 7 lines
COMPATIBLE_HOST= "(arm|arm-oe-linux-gnueabi).*-linux"$ MACHINE="solar" DISTRO="solar" bitbake core-image-minimal-initramfs ERROR: Nothing RPROVIDES 'initramfs-module-install' initramfs-module-install was skipped: incompatible with host arm-oe-linux-gnueabi (not in COMPATIBLE_HOST)
This is what I was saying. There seems to be a reason that arm architectures were not chosen as compatible with initramfs. You can pursue this problem further however (check what's initramfs-module-install) You may also look into Raspberry Pi yocto project. The community is larger and I doubt they have no functioning initramfs.
However at this point I can't give you any better advice.
Best regards and good luck
Moritz
Quoted 464 lines
Thank you very much.
- jupiter
Quoted 28 lines
Quoted 28 lines
Quoted 28 lines
$ MACHINE="solar" DISTRO="solar" bitbake solar-imageERROR: Nothing PROVIDES 'core-image-minimal-initramfs' core-image-minimal-initramfs was skipped: incompatible with host arm-oe-linux-gnueabi (not in
COMPATIBLE_HOST)
ERROR: Required build target 'solar-image' has no buildable providers. Missing or unbuildable dependency chain was: ['solar-image', 'virtual/kernel', 'core-image-minimal-initramfs']Sorry, still learning Yocto, what I could be missing?
Quoted 1 line
BOOT_IMAGE=/bzImage root=PARTUUID=71d1d94a-83e8-4895-98eb-35309f58119f
break=premount quiet rootwait rootwait rootfstype=ext4 console=ttyS0,115200 console=tty0
Which did you add kernel boot command for bootargs, bootcmd, etc as above? I could not find
BOOT_IMAGE(I use meta-freescale)Thank you very much.
- jupiter
Quoted 5 lines · Moritz Porst
Forgot to CC Jupiter and the most important thing:
PACKAGE_INSTALL+= "initramfs-module-debug" (To my understanding this
enables the rescue shell)Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines · Moritz Porst
Quoted 6 lines
Hey,
The only thing I can add to what I already said is my "core-image-minimal-initramfs.bbappend":
PACKAGE_INSTALL += "\ busybox \printenv
baudrate=115200
board_name=ULZ-EVK
board_rev=14X14> base-files \Quoted 420 lines
Quoted 420 lines
Quoted 420 lines
Quoted 420 lines
Quoted 420 lines
base-passwd \ bash \ util-linux-lsblk \ vim \ "Jupiter, are you able to produce your zImage-initramfs now ? If not further do the following:
bitbake <your-image> -e > tempfile
[wait until done, then search]
grep <appropriate search word> tempfilewhere <appropriate search word> may be e.g.: zImage, zImage-initramfs,
INITRAMFS_IMAGE,INITRAMFS_IMAGE_BUNDLE
Especially check that all variables you set are not overwritten somewhere elseBest regards
MoritzQuoted 399 lines · Zoran Stojsavljevic
Moritz,
Thank you very much for this reply. It makes it very clear... What is the current State of Affairs for the topic.
Let us see if there will be the improvement to this topic. I'll document this on one of my private GitHubs. And archive this email.
Zoran
_______Quoted 386 lines · Moritz Porst
Hello Zoran, Jupiter and list
The configuration you sent seems to be correct.
As I already said initramfs seems overly complicated in yocto. the most
important thing to note is that 2 kernel images are created, one is called bzImage (in my case) an the other bzImage-initramfs. However only
the bzImage is written into the rootfs so you have to exchange them manually. (in/boot/bzImage). I did not find a way of including the bundled kernel right away.What you can do is to build core-image-minimal-initramfs and delete the
symbolic link "bzImage", then recreate it and let it point to bzImage-initramfs. However this is rather a hack than a solution.An other mistake I made was to use
IMAGE_INSTALL_appendwhich is ignored. UsePACKAGE_INSTALL_append.Also I found that "break" does not work as a kernel parameter. Use "shell" oder "debug-shell" instead. If you want to try to boot into initramfs you can remove all parameters to the booting line so you either end up in a kernel panic (initramfs doesn't work) or in the rescue shell (initramfs works).
In the end I actually managed to get a working shell, but I often ended
up in initramfs telling me "dropping to shell..." but then freezing.I don't have access to my files right now but I can tell you more on my
setup tomorrow. In case the solution is not included above.Best regards
MoritzQuoted 347 lines · Zoran Stojsavljevic
Hello Moritz,
I need here some help from you. I'll try to reconstruct the parts of
the local.conf you are using, so I (and Jupiter) can understand what
should we do to also bundle kernel image with initramfs, to end up in
Dracut/rescue shell.Here is what I anticipate after reading several YOCTO @ threads:
IMAGE_FSTYPES_append= " cpio.gz"INITRAMFS_IMAGE= "core-image-minimal-initramfs"INITRAMFS_IMAGE_BUNDLE= "1"
# debug: adds debug boot parameters like 'shell' and 'debug', see# meta/recipes-core/initrdscripts/initramfs-framework/debug for details # Could be removed in more minimal product image PACKAGE_INSTALL += "initramfs-module-debug"Could you, please, review these lines and fix, if something is not correct?
I what I understood, this does the magic, but you could not stop in initramfs shell? Still, this problem is not solved?
Quoted 5 lines
I was following this site: https://wiki.debian.org/InitramfsDebug
Rescue shell (also known as initramfs shell)
Read man initramfs-tools to learn about the break=something kernel parameter (where valid arguments for something are: top, modules, premount, mount, mountroot, bottom, init), which starts a debugQuoted 8 lines
shell.
You can try, for example, break=premount. You can edit/boot/grub/grub.cfg
to add this to the end of the kernel line, or you can do it interactively
from the grub boot menu: "e" to edit, and "b" to boot once you've edited
the kernel line.Now, as my understanding is, you solved this problem actually adding
to grub.cfg in command kernel line break=premount, and was able to stop in rescue shell?! Am I correct here?Thank you,
Zoran
_______Quoted 295 lines · Moritz Porst
Hello,
I think I found the issue. ( see below )On 01.07.19 15:57, Zoran Stojsavljevic wrote:
Hello Moritz,
Too hot here, in Belgrade... Where I am resting for the Time being (actually, this message given to my invisible spying security "angels"
on this list)... :-) Projected +38C degrees today. Too hot for this
too old Siberian untouchable bobcat!Luckily it's a rather cold day in germany, thanks that you still take the time to answer !
I started from the core-image-minimal to have a small image and extended it with the features I need, which is e.g. a graphical system.
The console=[...] part in the kernel command line is probably a remnant but my image boots into the GUI. Is this a problem ?Nope, it is not. If you need to do it correctly, you should use bitbake -k core-image-sato build command (my best educated guess). Then, I do not feel comfortable seeing in your kernel command line serial interface, do you agree?
Yes that is true.
YOCTO maintainers, any additional
advices?My bootloader is currently grub, the EFI is AM.
Nope. Eeeeeeeeek. Wrong. Currently, your boot-loader is UEFI AMI. Your
OS (Linux probably, U name it) boot-loader is GRUB2. Let us keep it
contained, sane and sober.Sorry but I can't find this info in the EFI.
Could you, please try the following command being root: dmesg | grep
MCU. or grep mcu, or grep CPUID or grep cpuid?? Please, post results
to this list (to me).No luck unfortunately (used grep -i)
Could you, also, send to YOCTO list/me attached file:
/boot/microcode.cpioso I can somehow (?) inspect it? ;-)I send it to you directly, so I don't spam the list with a large attachment.
2GB, single channel.
All Cool. E3825 by HW/silicon design could/does NOT support multiple
memory channels. ONLY single... But even YOCTO primes (INTEL ones from
this list) are not gonna tell this to you. Not 'cause they are nasty.
They are NOT aware/they are ignorant (with the purpose)! ;-))No, the boot does not stop. Even if I do issue "break=premount" I end up in my graphical interface with the rootfs mounted. This is the
last message in the log: EXT4-fs (sdb2): re-mounted. Opts: (null) The rootfs partition is always 2, so either/dev/sda2or/dev/sdb2(when booting from stick)Yes, from https://pastebin.com/ya7iCtq7, so it is remounted rw, not
read only. So, it seems that you have passed dracut phase. and mounted
SD or flash rootfs. So, initramfs is NOT your true problem, is it???The thing is that the boot works but I want an initramfs that can be used for updating (in case the rootfs is broken). However I need to be able to intercept the boot process there because otherwise I can't deploy an update mechanism, that's what I was trying.
Zoran
_______No, the boot does not stop. Even if I do issue "break=premount" I end up
in my graphical interface with the rootfs mounted. This is the last message
in the log: EXT4-fs (sdb2): re-mounted. Opts: (null) The rootfs partition is
always 2, so either/dev/sda2or/dev/sdb2(when booting from stick)So for the issue...
I expected yocto to put the bundled bzImage onto my rootfs. This was not the case. My image directory contains 2x bzImage, one bundled and one unbundled. Apparently yocto puts the >un<bundled image onto my /boot partition and uses it for boot. So of course I couldn't access initramfs in this case. Now I get to the initramfs statement "dropping to shell" if I intentionally boot with wrong rootfs.
Still I don't get the interactive shell.
On the github ostroproject site I found this:# debug: adds debug boot parameters like 'shell' and 'debug', see
# meta/recipes-core/initrdscripts/initramfs-framework/debug for details # Could be removed in more minimal product image. PACKAGE_INSTALL += "initramfs-module-debug"including the module-debug still does not enable me to get an interactive shell.
I was following this site: https://wiki.debian.org/InitramfsDebug
I am aware that yocto is no debian but I expected that kernel parameters (like 'break') would be independent of the distribution.Lastly I do not really need the interactive shell, it is enough if I can deploy a custom init script in the initramfs. Still I think that getting an initramfs shell should be as simple as stating the name of the initramfs image and setting the "
INITRAMFS_DO_BUNDLE" variable.Best regards
MoritzOn Mon, Jul 1, 2019 at 11:20 AM Moritz Porst <[email protected]> wrote:
Hello Zoran,
thanks for your answerOn 28.06.19 14:26, Zoran Stojsavljevic wrote:
INITRAMFS_IMAGE= "core-image-minimal-initramfs"INITRAMFS_IMAGE_BUNDLE= "1"...
You can find the
/var/log/dmesghere:
https://pastebin.com/ya7iCtq7ISome hints...
[1] Kernel command line: BOOT_IMAGE=/bzImage root=PARTUUID=71d1d94a-83e8-4895-98eb-35309f58119f break=premount quiet rootwait rootwait rootfstype=ext4 console=ttyS0,115200 console=tty0
input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input7
fbcon: inteldrmfb (fb0) is primary device
Console: switching to colour frame buffer device 128x48 i915 0000:00:02.0: fb0: inteldrmfb frame buffer devicesnd_hda_intel0000:00:1b.0: bound 0000:00:02.0 (opsi915_audio_component_bind_ops[i915])Hmmmmm... You are using console and serial, but full i915 GFX kernel driver is still included in the build???
I started from the core-image-minimal to have a small image and extended it with the features I need, which is e.g. a graphical system. The console=[...] part in the kernel command line is probably a remnant but my image boots into the GUI. Is this a problem ?
[2] efi: EFI v2.31 by American Megatrends
Using AMI BIOS as boot loader FW... OK?! Am I correct?
My bootloader is currently grub, the EFI is AM.
[3] smpboot: CPU0: Intel(R) Atom(TM) CPU E3825 @ 1.33GHz (family:
0x6, model:0x37, stepping:0x9)This is CPUID ID
0x30679, which uses MCU... Which MicroCodeUnit? M0130679xxx (info from AMI BIOS)?Sorry but I can't find this info in the EFI
[4] Using INTEL ATOM BYT E3825 dual core (sans Hyper-threading), implies that you are using
4GB (e820 messages) as single channel (one memory module DDR3 as 4GB)! Am I correct (important)?2GB, single channel.
[5] Dracut phase?!
To my understanding the initramfs should be embedded in
/boot/bzImage.
However since I use an intel platform I also have a/boot/microcode.cpio
which gets loaded via "initrd /microcode.cpio". Removing this line in
grub does not enable me to get an initramfs prompt either (again, using
break as option).You are obviously stopping in boot phase called dracut. Please, try to mount by hand
/dev/sda(whatever)... You should use fdisk -l command, or do ls -al /dev | grep sda to
dig out which partition you need to mount to /tmp dir to see rootfstype=ext4 (HDD/SSD)No, the boot does not stop. Even if I do issue "break=premount" I end up in my graphical interface with the rootfs mounted. This is the last message in the log:
EXT4-fs (sdb2): re-mounted. Opts: (null)
The rootfs partition is always 2, so either/dev/sda2or/dev/sdb2(when booting from stick)_______
Just thinking loud... .. .
Hope this helps (has very little to do with YOCTO build system, BTW) . ;-)
Zoran
_______On Fri, Jun 28, 2019 at 11:22 AM Moritz Porst
<[email protected]> wrote:Hello,
I currently try to deploy a single rootfs update mechanism for my embedded device. I can't boot to initramfs using either "break" or "break=premount" (without quotes...). I tried this in systemd-boot and
grub-efi (always efi boot) but the boot process just continues normally.
If I insert at the same point e.g. "quiet" this argument is recognised.
I boot the .wic image with a separate boot partition from a USB stick.
in local.conf I have set:INITRAMFS_IMAGE= "core-image-minimal-initramfs"INITRAMFS_IMAGE_BUNDLE= "1"In order to reduce complexity I now use the standard core-image-minimal-initramfs without .bbappend. I can confirm (from
seeing the task) that bitbake bundled the kernel with the initramfs.You can find the
/var/log/dmesghere:
https://pastebin.com/ya7iCtq7To my understanding the initramfs should be embedded in
/boot/bzImage.
However since I use an intel platform I also have a/boot/microcode.cpio
which gets loaded via "initrd /microcode.cpio". Removing this line in
grub does not enable me to get an initramfs prompt either (again, using
break as option).Did I forget some configuration or do I have to put the break statement
at a very specific position within the "linux ..." boot command ? Do you
know which bitbake variables to check ? (both set in local.conf do not
get overwritten, already checked this). I got the thud branch checked
out in all my meta-layers except for meta-qt which is currently on master branch.Help is much appreciated !
Best regards
Moritz--
_______________________________________________
yocto mailing list
[email protected]
https://lists.yoctoproject.org/listinfo/yocto
Quoted 5 lines · Moritz Porst
If I use the .wic image, APPEND is ignored. You need to write your own kickstart file for this and include --append option. This usually means copy what you need from existing files (check license compliance) and add what you need. See the yocto manual on kickstart files:
https://www.yoctoproject.org/docs/latest/mega-manual/mega-manual.html#ref-kickstart
This is a bug in the wic files, and if they're still broken in master then please send a patch.
Notably this was the fix I did for the wic files in meta-intel:
wic/systemd-bootdisk-microcode.wks.in renamed from wic/systemd-bootdisk-microcode.wks +0 -2
@@ -10,4 +10,4 @@ part / --source rootfs --ondisk sda --fstype=ext4 --label platform --align 1024 -bootloader --ptable gpt --timeout=5 --append="rootwait
rootfstype=ext4 console=ttyS0,115200 console=tty0" +bootloader --ptable gpt --timeout=5 --append="rootfstype=ext4 ${APPEND}"
Easy! :)
Ross
Hi Moritz,
Thanks for your explanation, I know the copy from your script is for an example, Did you get the zImage-initramfs? I'll double check to follow your and Zoran documents.
Thank you.
- jupiter
Hey,
Quoted 5 lines · JH
Hi Moritz,
Thanks for your explanation, I know the copy from your script is for an example, Did you get the zImage-initramfs? I'll double check to follow your and Zoran documents.
Yes I have a working initramfs now. As I said the main problem for me was that I did not understand that the yocto build system puts the unbundled kernel into the rootfs. However I use x86 architecture. For you there seems to be a problem because of the architecture of your target. You will have to track the yocto recipes for initramfs back to understand why there is this limitation to architecture (and eventually adapt it). A shortcut could be to look at what the raspberry pi people did as I guess someone should have solved this problem. (Since raspberry pi is also ARM)
Quoted 4 lines
Thank you.
- jupiter
Good luck
Moritz
Hi Zoran,
Quoted 7 lines · Zoran Stojsavljevic
Moritz,
Thank you very much for this reply. It makes it very clear... What is the current State of Affairs for the topic.
Let us see if there will be the improvement to this topic. I'll document this on one of my private GitHubs. And archive this email.
Any chance to access your documents?
Thank you.
- jupiter
Hello Jupiter,
I actually continued this topic initiated by Moritz, to find out how you and me and somebody else also can build the yocto build system with bundled rescue kernel into the rootfs.
My target architecture I am playing with is armv7 A8 (BBB), since I am experimenting with it.
I actually built the armv7 A8 (BBB) with the unbundled initramfs, where the BSP actually ends up for the testing purposes. All this how I did it is described here:
https://lists.yoctoproject.org/pipermail/yocto/2018-July/041696.html
Here is also latest local.conf for warrior (how I am buillding it):
https://github.com/ZoranStojsavljevic/bbb-yocto/blob/master/bbb-releases/bbb-warrior/local.conf_full
I never built such a system with rescue initramfs, ending with/in rootfs on mtd/flash, or SD card, YOCTO wise, so I actually continued this topic to find out exactly the same what you asked me above.
You can go over this email thread, and try while building with what we all put as collection of patchworks.
I have no time to do this, since I need very urgently to do some other important for me stuff on BBB.
Zoran
_______
Quoted 17 lines · JH
Hi Zoran,
Quoted 7 lines · Zoran Stojsavljevic
Moritz,
Thank you very much for this reply. It makes it very clear... What is the current State of Affairs for the topic.
Let us see if there will be the improvement to this topic. I'll document this on one of my private GitHubs. And archive this email.
Any chance to access your documents?
Thank you.
- jupiter
Thanks Zoran, I have tools to test it, I'll try it, it will be a long journey though.
Thank you.
- jupter
Quoted 52 lines · Zoran Stojsavljevic
Hello Jupiter,
I actually continued this topic initiated by Moritz, to find out how you and me and somebody else also can build the yocto build system with bundled rescue kernel into the rootfs.
My target architecture I am playing with is armv7 A8 (BBB), since I am experimenting with it.
I actually built the armv7 A8 (BBB) with the unbundled initramfs, where the BSP actually ends up for the testing purposes. All this how I did it is described here:
https://lists.yoctoproject.org/pipermail/yocto/2018-July/041696.htmlHere is also latest local.conf for warrior (how I am buillding it):
https://github.com/ZoranStojsavljevic/bbb-yocto/blob/master/bbb-releases/bbb-warrior/local.conf_fullI never built such a system with rescue initramfs, ending with/in rootfs on mtd/flash, or SD card, YOCTO wise, so I actually continued this topic to find out exactly the same what you asked me above.
You can go over this email thread, and try while building with what we all put as collection of patchworks.
I have no time to do this, since I need very urgently to do some other important for me stuff on BBB.
Zoran
_______Quoted 17 lines · JH
Hi Zoran,
Quoted 7 lines · Zoran Stojsavljevic
Moritz,
Thank you very much for this reply. It makes it very clear... What is the current State of Affairs for the topic.
Let us see if there will be the improvement to this topic. I'll document this on one of my private GitHubs. And archive this email.
Any chance to access your documents?
Thank you.
- jupiter