xen/arm: Restrict "p2m_ipa_bits" according to the IOMMU requirements
RFC PATCH v3 1/1 xen/arm: Restrict "p2m_ipa_bits" according to the IOMMU requirements
From: Oleksandr Tyshchenko <[email protected]>
There is a strict requirement for the IOMMU which wants to share the P2M table with the CPU. The IOMMU's Stage-2 input size must be equal to the P2M IPA size. It is not a problem when the IOMMU can support all values the CPU supports. In that case, the IOMMU driver would just use any "p2m_ipa_bits" value as is. But, there are cases when not.
In order to make P2M sharing possible on the platforms which IOMMUs have a limitation in maximum Stage-2 input size introduce the following logic.
First initialize the IOMMU subsystem and gather requirements regarding the maximum IPA bits supported by each IOMMU device to figure out the minimum value among them. In the P2M code, take into the account the IOMMU requirements and choose suitable "pa_range" according to the restricted "p2m_ipa_bits".
---
Still RFC:
1. Patch assumes that IPMMU support is already in.
2. Not checked for the SMMU.
Changes RFC V2 [2] -> RFC V3:
- Check in setup_virt_paging() that the "restricted" P2M IPA size is at least 40-bit
- Modify logic in setup_virt_paging() a bit to make it "IOMMU-agnostic"
- Clarify comments in code, add some explanations
- Avoid using the term "IOMMU" in P2M code where possible
Changes RFC V1 [1] -> RFC V2 [2]:
- Don't update p2m_ipa_bits by the IOMMU drivers directly, introduce p2m_restrict_ipa_bits()
- Clarify patch subject/description
- Add more comments to code
- Check for equivalent "pabits" in setup_virt_paging()
- Remove ASSERTs from the SMMU and IPMMU drivers
[1] https://lists.xenproject.org/archives/html/xen-devel/2019-08/msg02078.html
[2] https://lists.xenproject.org/archives/html/xen-devel/2019-08/msg02237.html
--- xen/arch/arm/p2m.c | 41 ++++++++++++++++++++++++++++---- xen/arch/arm/setup.c | 9 +++++-- xen/drivers/passthrough/arm/ipmmu-vmsa.c | 18 ++------------ xen/drivers/passthrough/arm/smmu.c | 11 +++------ xen/include/asm-arm/p2m.h | 9 +++++++ 5 files changed, 58 insertions(+), 30 deletions(-)
xen/arch/arm/p2m.c +37 -4
@@ -34,7 +34,11 @@ static unsigned int __read_mostly max_vmid = MAX_VMID_8_BIT;#define P2M_ROOT_PAGES (1<<P2M_ROOT_ORDER) -unsigned int __read_mostly p2m_ipa_bits; +/* +* Set larger than any possible value, so the number of IPA bits can be +* restricted by external entity (e.g. IOMMU). +*/ +unsigned int __read_mostly p2m_ipa_bits =64 ;/* Helpers to lookup the properties of each level */ static const paddr_t level_masks[] =
@@ -1912,6 +1916,16 @@ struct page_info *get_page_from_gva(struct vcpu *v, vaddr_t va,return page; } +void __init p2m_restrict_ipa_bits (unsigned int ipa_bits) +{ +/* +* Calculate the minimum of the maximum IPA bits that any external entity +* can support. +*/ +if ( ipa_bits < p2m_ipa_bits ) + p2m_ipa_bits = ipa_bits; +} +/* VTCR value to be configured by all CPUs. Set only once by the boot CPU */ static uint32_t __read_mostly vtcr;
@@ -1966,15 +1980,24 @@ void __init setup_virt_paging(void) [7] = { 0 } /* Invalid */ }; -unsigned int cpu; +unsigned int i, cpu;unsigned int pa_range =0x10 ;/* Larger than any possible value */ bool vmid_8_bit = false; +if ( p2m_ipa_bits <40 ) +panic ("P2M IPA size must be at least 40-bit (p2m_ipa_bits=%u)\n" , + p2m_ipa_bits); +for_each_online_cpu ( cpu ) {const struct cpuinfo_arm *info = &cpu_data[cpu]; -if ( info->mm64.pa_range < pa_range ) - pa_range = info->mm64.pa_range; + +/* +* Restrict "p2m_ipa_bits" if needed. As P2M table is always configured +* with IPA bits == PA bits, compare against "pabits". +*/ +if ( pa_range_info[info->mm64.pa_range].pabits < p2m_ipa_bits ) + p2m_ipa_bits = pa_range_info[info->mm64.pa_range].pabits;/* Set a flag if the current cpu does not support 16 bit VMIDs. */ if ( info->mm64.vmid_bits !=MM64_VMID_16_BITS_SUPPORT )
@@ -1988,6 +2011,16 @@ void __init setup_virt_paging(void)if ( !vmid_8_bit ) max_vmid =MAX_VMID_16_BIT ; +/* Choose suitable "pa_range" according to the resulted "p2m_ipa_bits". */ +for ( i =0 ; i <ARRAY_SIZE (pa_range_info); i++ ) + { +if ( p2m_ipa_bits == pa_range_info[i].pabits ) + { + pa_range = i; +break ; + } + } +/* pa_range is 4 bits, but the defined encodings are only 3 bits */ if ( pa_range >=ARRAY_SIZE (pa_range_info) || !pa_range_info[pa_range].pabits )panic ("Unknown encoding of ID_AA64MMFR0_EL1.PARange %x\n" , pa_range);
xen/arch/arm/setup.c +7 -2
@@ -936,12 +936,17 @@ void __init start_xen(unsigned long boot_phys_offset,printk ("Brought up %ld CPUs\n" , (long )num_online_cpus ());/* TODO: smp_cpus_done(); */ -setup_virt_paging (); - +/* +* The IOMMU subsystem must be initialized before P2M as we need +* to gather requirements regarding the maximum IPA bits supported by +* each IOMMU device. +*/ rc =iommu_setup ();if ( !iommu_enabled && rc != -ENODEV )panic ("Couldn't configure correctly all the IOMMUs." ); +setup_virt_paging (); +do_initcalls ();/*
xen/drivers/passthrough/arm/ipmmu-vmsa.c +2 -16
@@ -844,22 +844,8 @@ static int ipmmu_probe(struct dt_device_node *node) goto out; } -/* -* As 4-level translation table is not supported in IPMMU, we need -* to check IPA size used for P2M table beforehand to be sure it is -* 3-level and the IPMMU will be able to use it. -* -* TODO: First initialize the IOMMU and gather the requirements and -* then initialize the P2M. In the P2M code, take into the account -* the IOMMU requirements and restrict "pa_range" if necessary. -*/ -if (IPMMU_MAX_P2M_IPA_BITS < p2m_ipa_bits ) - { -printk (XENLOG_ERR "ipmmu: P2M IPA size is not supported (P2M=%u IPMMU=%u)!\n" , - p2m_ipa_bits,IPMMU_MAX_P2M_IPA_BITS ); - ret = -ENODEV ; - goto out; - } +/* Set maximum Stage-2 input size supported by the IPMMU. */ +p2m_restrict_ipa_bits (IPMMU_MAX_P2M_IPA_BITS ); irq =platform_get_irq (node,0 );if ( irq <0 )
xen/drivers/passthrough/arm/smmu.c +3 -8
@@ -2198,14 +2198,9 @@ static int arm_smmu_device_cfg_probe(struct arm_smmu_device *smmu) size =arm_smmu_id_size_to_bits ((id >>ID2_IAS_SHIFT ) &ID2_IAS_MASK ); smmu->s1_output_size = min_t(unsigned long, PHYS_MASK_SHIFT, size); -/* Xen: Stage-2 input size has to match p2m_ipa_bits. */ -if (size < p2m_ipa_bits) { -dev_err (smmu->dev, -"P2M IPA size not supported (P2M=%u SMMU=%lu)!\n" , - p2m_ipa_bits, size); -return -ENODEV ; - } - smmu->s2_input_size = p2m_ipa_bits; +/* Xen: Set maximum Stage-2 input size supported by the SMMU. */ +p2m_restrict_ipa_bits (size); + smmu->s2_input_size = size;#if 0 /* Stage-2 input size limited due to pgd allocation (PTRS_PER_PGD) */ #ifdef CONFIG_64BIT
xen/include/asm-arm/p2m.h +9 -0
@@ -165,6 +165,15 @@ void p2m_altp2m_check(struct vcpu *v, uint16_t idx)/* Not supported on ARM. */ } +/* +* Helper to restrict "p2m_ipa_bits" according the external entity +* (e.g. IOMMU) requirements. +* +* Each corresponding driver should report the maximum IPA bits +* (Stage-2 input size) it can support. +*/ +void p2m_restrict_ipa_bits (unsigned int ipa_bits); +/* Second stage paging setup, to be called on all CPUs */ void setup_virt_paging (void );
Signature · 7 lines
2.7.4 _______________________________________________ Xen-devel mailing list [email protected] https://lists.xenproject.org/mailman/listinfo/xen-devel
Hi,
Quoted 44 lines · Oleksandr Tyshchenko
--- xen/arch/arm/p2m.c | 41 ++++++++++++++++++++++++++++---- xen/arch/arm/setup.c | 9 +++++-- xen/drivers/passthrough/arm/ipmmu-vmsa.c | 18 ++------------ xen/drivers/passthrough/arm/smmu.c | 11 +++------ xen/include/asm-arm/p2m.h | 9 +++++++ 5 files changed, 58 insertions(+), 30 deletions(-)xen/arch/arm/p2m.c +15
-1@@ -34,7 +34,11 @@ static unsigned int __read_mostly max_vmid = MAX_VMID_8_BIT;#define P2M_ROOT_PAGES (1<<P2M_ROOT_ORDER) -unsigned int __read_mostly p2m_ipa_bits; +/* +* Set larger than any possible value, so the number of IPA bits can be +* restricted by external entity (e.g. IOMMU). +*/ +unsigned int __read_mostly p2m_ipa_bits =64 ;/* Helpers to lookup the properties of each level */ static const paddr_t level_masks[] =@@ -1912,6 +1916,16 @@ struct page_info *get_page_from_gva(struct vcpu *v, vaddr_t va,return page; } +void __init p2m_restrict_ipa_bits (unsigned int ipa_bits) +{ +/* +* Calculate the minimum of the maximum IPA bits that any external entity +* can support. +*/ +if ( ipa_bits < p2m_ipa_bits ) + p2m_ipa_bits = ipa_bits; +} +/* VTCR value to be configured by all CPUs. Set only once by the boot CPU */ static uint32_t __read_mostly vtcr;@@ -1966,15 +1980,24 @@ void __init setup_virt_paging(void) [7 ] = {0 }/* Invalid */
xen/arch/arm/p2m.c void __init setup_virt_paging(void) · line 1989
Quoted 10 lines
xen/arch/arm/p2m.c +4
-1}; -unsigned int cpu; +unsigned int i, cpu;unsigned int pa_range =0x10 ;/* Larger than any possible value */ bool vmid_8_bit = false; +if ( p2m_ipa_bits <40 ) +panic ("P2M IPA size must be at least 40-bit (p2m_ipa_bits=%u)\n" , + p2m_ipa_bits);
Isn't this check meant to be for Arm32? If so, this path is not called by arm32. See the #ifdef CONFIG_ARM_32 above.
Also, I would suggest to reword the message to:
"P2M: Not able to support %⁻bit IPA at the moment.\n"
The rest of the code looks good to me.
Cheers,
Signature · 6 lines
Julien Grall _______________________________________________ Xen-devel mailing list [email protected] https://lists.xenproject.org/mailman/listinfo/xen-devel
Quoted 1 line · Julien Grall
Hi,
Hi, Julien
Quoted 48 lines · Oleksandr Tyshchenko
Quoted 46 lines
---
xen/arch/arm/p2m.c | 41
++++++++++++++++++++++++++++----
xen/arch/arm/setup.c | 9 +++++--xen/drivers/passthrough/arm/ipmmu-vmsa.c| 18 ++------------ xen/drivers/passthrough/arm/smmu.c | 11 +++------ xen/include/asm-arm/p2m.h | 9 +++++++5 files changed, 58 insertions(+), 30 deletions(-)xen/arch/arm/p2m.c +5
-0@@ -34,7 +34,11 @@ static unsigned int __read_mostly max_vmid =MAX_VMID_8_BIT ; #define P2M_ROOT_PAGES (1<<P2M_ROOT_ORDER) -unsigned int __read_mostly p2m_ipa_bits; +/* +* Set larger than any possible value, so the number of IPA bits can be +* restricted by external entity (e.g. IOMMU). +*/ +unsigned int __read_mostly p2m_ipa_bits =64 ; /* Helpers to lookup the properties of each level */static const
paddr_tlevel_masks[] =xen/arch/arm/p2m.c +3
-0@@ -1912,6 +1916,16 @@ struct page_info *get_page_from_gva(struct vcpu *v, vaddr_t va, return page; } +void __init p2m_restrict_ipa_bits(unsigned int ipa_bits) +{ + /* +* Calculate the minimum of the maximum IPA bits that any external entity
+ * can support.
+ */
+ if (ipa_bits<p2m_ipa_bits)
+p2m_ipa_bits=ipa_bits;xen/arch/arm/p2m.c +2
-0+} +/* VTCR value to be configured by all CPUs. Set only once by the boot CPU */ static
uint32_t__read_mostlyvtcr;
@@ -1966,15 +1980,24 @@ void__initsetup_virt_paging(void)
[7] = { 0 } /* Invalid */
};
- unsigned int cpu;
+ unsigned int i, cpu;
Quoted 8 lines
Quoted 6 lines
unsigned int
pa_range=0x10; /* Larger than any possible value */ boolvmid_8_bit= false;
+ if (p2m_ipa_bits< 40 )
+ panic("P2M IPA size must be at least 40-bit (p2m_ipa_bits=%u)\n",
+p2m_ipa_bits);Isn't this check meant to be for Arm32? If so, this path is not called by arm32. See the #ifdef
CONFIG_ARM_32above.
I will move under #ifdef CONFIG_ARM_32
Quoted 5 lines
Also, I would suggest to reword the message to:
"P2M: Not able to support %⁻bit IPA at the moment.\n"
ok
Quoted 2 lines
The rest of the code looks good to me.
Shall the non-RFC patch be split into "adding possibility to restrict" and "restrict by the IOMMU drivers"?
Signature · 9 lines
Regards, Oleksandr Tyshchenko _______________________________________________ Xen-devel mailing list [email protected] https://lists.xenproject.org/mailman/listinfo/xen-devel
Hi,
Quoted 5 lines · Oleksandr
Quoted 1 line · Julien Grall
The rest of the code looks good to me.
Shall the non-RFC patch be split into "adding possibility to restrict" and "restrict by the IOMMU drivers"?
The patch is fine as it is. No need to split further :).
Cheers,
Signature · 6 lines
Julien Grall _______________________________________________ Xen-devel mailing list [email protected] https://lists.xenproject.org/mailman/listinfo/xen-devel