ARM: shmobile: kzm9g: add irqpin to DT
Subsystems (3)
cover ARM: shmobile: kzm9g: add irqpin to DT
These 3 patches extend irqpin DT bindings to more completely support sh73a0, add irqpin DT nodes to sh73a0.dtsi and use them to add ethernet support to kzm9g-reference.
Thanks
Guennadi
---
Guennadi Liakhovetski, Ph.D.
Freelance Open-Source Software Developer
http://www.open-technology.de/
PATCH 1/3 ARM: shmobile: irqpin: fix handling of spurious interrupts in DT case
To disable spurious interrupts, that get triggered on certain hardware, the irqpin driver masks them on the parent interrupt controller. To specify such broken devices a .control_parent parameter can be provided in the platform data. In the DT case we need a property, to do the same. However, this is not enough to correctly handle spurious interrupts in the DT case. In the non-DT case all interrupts get mapped statically during probing, therefore, if a spurious interrupt arrives, it can easily be mapped back to hardware registers and bits and handled. In the DT case interrupts are mapped only when a device, using that interrupt is instantiated from DT. So, spurious interrupts occur unmapped and thus cannot be handled properly. This patch fixes this by mapping such interrupts as they occur.
--- .../interrupt-controller/renesas,intc-irqpin.txt | 13 +++++++++++++ drivers/irqchip/irq-renesas-intc-irqpin.c | 13 +++++++++++++ 2 files changed, 26 insertions(+), 0 deletions(-) create mode 100644 Documentation/devicetree/bindings/interrupt-controller/renesas,intc-irqpin.txt
Documentation/devicetree/bindings/interrupt-controller/renesas,intc-irqpin.txt new file +13 -0
@@ -0,0 +1,13 @@ +DT bindings for the R-/SH-Mobile irqpin controller + +Required properties: + +- compatible: has to be "renesas,intc-irqpin" +- #interrupt-cells: has to be <2> + +Optional properties: + +- any properties, listed in interrupts.txt in this directory, and any standard + resource allocation properties +- control-parent: disable and enable interrupts on the parent interrupt + controller, needed for some broken implementations
drivers/irqchip/irq-renesas-intc-irqpin.c +13 -0
@@ -18,6 +18,7 @@*/ #include <linux/init.h> +#include <linux/of.h> #include <linux/platform_device.h> #include <linux/spinlock.h> #include <linux/interrupt.h>
@@ -70,6 +71,7 @@ struct intc_irqpin_priv {struct intc_irqpin_iomem iomem[INTC_IRQPIN_REG_NR ];struct intc_irqpin_irq irq[INTC_IRQPIN_MAX ];struct renesas_intc_irqpin_config config; +unsigned int min_irq;unsigned int number_of_irqs;struct platform_device *pdev;struct irq_chip irq_chip;
@@ -249,6 +251,10 @@ static irqreturn_t intc_irqpin_irq_handler(int irq, void *dev_id)struct intc_irqpin_priv *p = i->p;unsigned long bit; +if (!i->domain_irq) +/* unmapped: spurious IRQ, map it now */ +irq_create_mapping (p->irq_domain, irq - p->min_irq); +intc_irqpin_dbg (i,"demux1" ); bit =intc_irqpin_hwirq_mask (p,INTC_IRQPIN_REG_SOURCE , i->hw_irq);
@@ -321,6 +327,7 @@ static int intc_irqpin_probe(struct platform_device *pdev) } } + p->min_irq =INT_MAX ;/* allow any number of IRQs between 1 and INTC_IRQPIN_MAX */ for (k =0 ; k <INTC_IRQPIN_MAX ; k++) { irq =platform_get_resource (pdev,IORESOURCE_IRQ , k);
@@ -329,6 +336,8 @@ static int intc_irqpin_probe(struct platform_device *pdev) p->irq[k].p = p; p->irq[k].requested_irq = irq->start; +if (p->min_irq > irq->start) + p->min_irq = irq->start; } p->number_of_irqs = k;
@@ -372,6 +381,10 @@ static int intc_irqpin_probe(struct platform_device *pdev)for (k =0 ; k < p->number_of_irqs; k++)intc_irqpin_mask_unmask_prio (p, k,1 ); +if (!pdata) + p->config.control_parent =of_property_read_bool (pdev->dev.of_node, +"control-parent" ); +/* use more severe masking method if requested */ if (p->config.control_parent) { enable_fn = intc_irqpin_irq_enable_force;
Signature · 1 line
1.7.2.5
PATCH 1/3 ARM: shmobile: irqpin: fix handling of spurious interrupts in DT case
Quoted 12 lines · Guennadi Liakhovetski
To disable spurious interrupts, that get triggered on certain hardware, the irqpin driver masks them on the parent interrupt controller. To specify such broken devices a .control_parent parameter can be provided in the platform data. In the DT case we need a property, to do the same. However, this is not enough to correctly handle spurious interrupts in the DT case. In the non-DT case all interrupts get mapped statically during probing, therefore, if a spurious interrupt arrives, it can easily be mapped back to hardware registers and bits and handled. In the DT case interrupts are mapped only when a device, using that interrupt is instantiated from DT. So, spurious interrupts occur unmapped and thus cannot be handled properly. This patch fixes this by mapping such interrupts as they occur.
Quoted 1 line
Signed-off-by Guennadi Liakhovetski <[email protected]>
Thanks, queued up for v3.10 in the intc-external-irq branch of the renesas tree.
PATCH 1/3 ARM: shmobile: irqpin: fix handling of spurious interrupts in DT case
Quoted 13 lines · Simon Horman
Quoted 12 lines · Guennadi Liakhovetski
To disable spurious interrupts, that get triggered on certain hardware, the irqpin driver masks them on the parent interrupt controller. To specify such broken devices a .control_parent parameter can be provided in the platform data. In the DT case we need a property, to do the same. However, this is not enough to correctly handle spurious interrupts in the DT case. In the non-DT case all interrupts get mapped statically during probing, therefore, if a spurious interrupt arrives, it can easily be mapped back to hardware registers and bits and handled. In the DT case interrupts are mapped only when a device, using that interrupt is instantiated from DT. So, spurious interrupts occur unmapped and thus cannot be handled properly. This patch fixes this by mapping such interrupts as they occur.
Quoted 3 lines
Quoted 1 line
Signed-off-by Guennadi Liakhovetski <[email protected]>Thanks, queued up for v3.10 in the intc-external-irq branch of the renesas tree.
As requested by Magnus I have dropped this patch.
PATCH 1/3 ARM: shmobile: irqpin: fix handling of spurious interrupts in DT case
Quoted 15 lines · On Thursday 28 March 2013 14:30:45 Simon Horman wrote:
Quoted 14 lines · Simon Horman
Quoted 13 lines · Guennadi Liakhovetski
To disable spurious interrupts, that get triggered on certain hardware, the irqpin driver masks them on the parent interrupt controller. To specify such broken devices a .control_parent parameter can be provided in the platform data. In the DT case we need a property, to do the same. However, this is not enough to correctly handle spurious interrupts in the DT case. In the non-DT case all interrupts get mapped statically during probing, therefore, if a spurious interrupt arrives, it can easily be mapped back to hardware registers and bits and handled. In the DT case interrupts are mapped only when a device, using that interrupt is instantiated from DT. So, spurious interrupts occur unmapped and thus cannot be handled properly. This patch fixes this by mapping such interrupts as they occur.
Quoted 6 lines
Quoted 4 lines
Quoted 1 line
Signed-off-by Guennadi Liakhovetski <[email protected]>Thanks, queued up for v3.10 in the intc-external-irq branch of the renesas tree.
As requested by Magnus I have dropped this patch.
I'm running into similar spurious interrupt issues on both kzm9g-reference and marzen-reference. Magnus, you've rejected this patch, how would you like the issue to be fixed ? Could you please provide a patch ? This is blocking pinctrl DT testing, as I can't get any board to boot properly through DT with ethernet support.
Signature · 3 lines
Regards, Laurent Pinchart
PATCH 2/3 ARM: shmobile: sh73a0: add irqpin DT nodes
In reply to Guennadi LiakhovetskiAdd DT nodes for the 4 irqpin interrupt controllers on sh73a0. We add them to sh73a0.dtsi, which is also used by configurations, doing all their device instantiation from board the .c code. We rely on the fact, that such configurations don't instantiate devices from the device-tree.
--- arch/arm/boot/dts/sh73a0.dtsi | 81 +++++++++++++++++++++++++++++++++++++++++ 1 files changed, 81 insertions(+), 0 deletions(-)
arch/arm/boot/dts/sh73a0.dtsi +81 -0
@@ -38,6 +38,87 @@ <0xf0000100 0x100>; }; + irqpin0: irqpin at e6900000 { + compatible = "renesas,intc-irqpin"; + #interrupt-cells = <2>; + interrupt-controller; + reg = <0xe6900000 4>, + <0xe6900010 4>, + <0xe6900020 1>, + <0xe6900040 1>, + <0xe6900060 1>; + interrupt-parent = <&gic>; + interrupts = <0 1 0x4 + 0 2 0x4 + 0 3 0x4 + 0 4 0x4 + 0 5 0x4 + 0 6 0x4 + 0 7 0x4 + 0 8 0x4>; + }; + + irqpin1: irqpin at e6900004 { + compatible = "renesas,intc-irqpin"; + #interrupt-cells = <2>; + interrupt-controller; + reg = <0xe6900004 4>, + <0xe6900014 4>, + <0xe6900024 1>, + <0xe6900044 1>, + <0xe6900064 1>; + interrupt-parent = <&gic>; + interrupts = <0 9 0x4 + 0 10 0x4 + 0 11 0x4 + 0 12 0x4 + 0 13 0x4 + 0 14 0x4 + 0 15 0x4 + 0 16 0x4>; + control-parent; + }; + + irqpin2: irqpin at e6900008 { + compatible = "renesas,intc-irqpin"; + #interrupt-cells = <2>; + interrupt-controller; + reg = <0xe6900008 4>, + <0xe6900018 4>, + <0xe6900028 1>, + <0xe6900048 1>, + <0xe6900068 1>; + interrupt-parent = <&gic>; + interrupts = <0 17 0x4 + 0 18 0x4 + 0 19 0x4 + 0 20 0x4 + 0 21 0x4 + 0 22 0x4 + 0 23 0x4 + 0 24 0x4>; + }; + + irqpin3: irqpin at e690000c { + compatible = "renesas,intc-irqpin"; + #interrupt-cells = <2>; + interrupt-controller; + reg = <0xe690000c 4>, + <0xe690001c 4>, + <0xe690002c 1>, + <0xe690004c 1>, + <0xe690006c 1>; + interrupt-parent = <&gic>; + interrupts = <0 25 0x4 + 0 26 0x4 + 0 27 0x4 + 0 28 0x4 + 0 29 0x4 + 0 30 0x4 + 0 31 0x4 + 0 32 0x4>; + }; + i2c0: i2c at 0xe6820000 { #address-cells = <1>; #size-cells = <0>;
Signature · 1 line
1.7.2.5
PATCH 2/3 ARM: shmobile: sh73a0: add irqpin DT nodes
Quoted 4 lines · Guennadi Liakhovetski
Add DT nodes for the 4 irqpin interrupt controllers on sh73a0. We add them to
sh73a0.dtsi, which is also used by configurations, doing all their device instantiation from board the .c code. We rely on the fact, that such configurations don't instantiate devices from the device-tree.
Thanks, queued up for v3.10 in the soc branch of the renesas tree.
PATCH 3/3 ARM: shmobile: kzm9g-reference: add ethernet support
In reply to Guennadi LiakhovetskiAdd a DT node for the SMSC 9221 ethernet chip, found on kzm9g, to its reference implementation.
--- arch/arm/boot/dts/sh73a0-kzm9g-reference.dts | 13 +++++++++++++ 1 files changed, 13 insertions(+), 0 deletions(-)
arch/arm/boot/dts/sh73a0-kzm9g-reference.dts +13 -0
@@ -44,6 +44,19 @@ regulator-always-on; regulator-boot-on; }; + + lan9220 at 10000000 { + compatible = "smsc,lan9220", "smsc,lan9115"; + reg = <0x10000000 0x100>; + phy-mode = "mii"; + interrupt-parent = <&irqpin0>; + interrupts = <3 0>; /* active low */ + reg-io-width = <4>; + smsc,irq-push-pull; + smsc,save-mac-address; + vddvario-supply = <®_1p8v>; + vdd33a-supply = <®_3p3v>; + }; }; &mmcif {
Signature · 1 line
1.7.2.5
PATCH 3/3 ARM: shmobile: kzm9g-reference: add ethernet support
Quoted 2 lines · Guennadi Liakhovetski
Add a DT node for the SMSC 9221 ethernet chip, found on kzm9g, to its reference implementation.
Thanks, queued up for v3.10 in the boards branch of the renesas tree.
cover ARM: shmobile: kzm9g: add irqpin to DT
In reply to Guennadi LiakhovetskiQuoted 3 lines · Guennadi Liakhovetski
These 3 patches extend irqpin DT bindings to more completely support sh73a0, add irqpin DT nodes to
sh73a0.dtsiand use them to add ethernet support to kzm9g-reference.
Hi Guennadi,
thanks for this. I am really happy to see this change.
I wonder if it might be possible for you to wire up similar changes for the r8a7779/marzen. reference-marzen claims to support the SMSC LAN in its dts file, however it doesn't work due to missing irqpin setup.
If so I can test any patches you make.
Or I can give you remote access to a marzen.
Whichever works best for you.