Skip to contentSkip to conversation

VIA IDE driver status ?

DISCUSSION Frédéric L. W. Meunier 2 participants 4 messages Mar 31, 2001

lore
Share & tools
lore
#0 lore raw

Hi. I really can't get UDMA66 with the VIA driver. I tried everything, also a new motherboard (ASUS A7Pro) with a ATA100/ATA66 cable (using both ends...)!

All I get are the usual CRC error messages.

So, there's no UDMA66 for any vt82c686a ? I'm using 2.4.3.

If there's no UDMA66, what are the advantages using this driver ?

TIA.

Signature · 1 line
0@pervalidus.{net, {dyndns.}org} Tel: 55-21-717-2399 (Niterói-RJ BR)
#1 lore raw

I am not sure if this applies in your case, but I was getting problems such as this on my Abit KT7-RAID and had the correct cables, also. One day, on a hunch after reading a post from Alan about overclocking, I took my Athlon 750 down to 850 from 1.05 GHz and all is working great now. If your overclocking, I would suggest not doing so (at least not so much), based on my experience. I am also using the v4.0 driver.

Chris

Quoted 20 lines · Frédéric L. W. Meunier

Hi. I really can't get UDMA66 with the VIA driver. I tried everything, also a new motherboard (ASUS A7Pro) with a ATA100/ATA66 cable (using both ends...)!

All I get are the usual CRC error messages.

So, there's no UDMA66 for any vt82c686a ? I'm using 2.4.3.

If there's no UDMA66, what are the advantages using this driver ?

TIA.

Signature · 6 lines
0@pervalidus.{net, {dyndns.}org} Tel: 55-21-717-2399 (Niterói-RJ BR)
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/
#2 lore raw
In reply to Frédéric L. W. Meunier

I'm not overclocking. It's an ASUS A7Pro with Athlon 1000. I had the same problem with an ASUS K7V with Athlon 700. But the processor died after my cooler failed for 20 minutes!

BTW, how do I know if my cable is ATA100/ATA66, not only ATA66 ? The manual from the A7Pro says it supports both, but at the site it says the cable shipped with this motherboard is ATA66.

Quoted 22 lines · Glenn C. Hofmann

I am not sure if this applies in your case, but I was getting problems such as this on my Abit KT7-RAID and had the correct cables, also. One day, on a hunch after reading a post from Alan about overclocking, I took my Athlon 750 down to 850 from 1.05 GHz and all is working great now. If your overclocking, I would suggest not doing so (at least not so much), based on my experience. I am also using the v4.0 driver.

Chris

Quoted 12 lines · Frédéric L. W. Meunier

Hi. I really can't get UDMA66 with the VIA driver. I tried everything, also a new motherboard (ASUS A7Pro) with a ATA100/ATA66 cable (using both ends...)!

All I get are the usual CRC error messages.

So, there's no UDMA66 for any vt82c686a ? I'm using 2.4.3.

If there's no UDMA66, what are the advantages using this driver ?

TIA.

Signature · 1 line
0@pervalidus.{net, {dyndns.}org} Tel: 55-21-717-2399 (Niterói-RJ BR)
#3 lore raw

It should support both, to my knowledge (which is very limited, mind you). I also went out to the store and purchased a new cable, which made the driver recognize the cable correctly, whereas it did not before. I wonder if there is not a serious deficiency in the cables sent out with motherboards, which is contributing to the problems a lot of people are having in this area. Hope this helps some.

Chris

Quoted 39 lines · Frédéric L. W. Meunier

I'm not overclocking. It's an ASUS A7Pro with Athlon 1000. I had the same problem with an ASUS K7V with Athlon 700. But the processor died after my cooler failed for 20 minutes!

BTW, how do I know if my cable is ATA100/ATA66, not only ATA66 ? The manual from the A7Pro says it supports both, but at the site it says the cable shipped with this motherboard is ATA66.

Quoted 22 lines · Glenn C. Hofmann

I am not sure if this applies in your case, but I was getting problems such as this on my Abit KT7-RAID and had the correct cables, also. One day, on a hunch after reading a post from Alan about overclocking, I took my Athlon 750 down to 850 from 1.05 GHz and all is working great now. If your overclocking, I would suggest not doing so (at least not so much), based on my experience. I am also using the v4.0 driver.

Chris

Quoted 12 lines · Frédéric L. W. Meunier

Hi. I really can't get UDMA66 with the VIA driver. I tried everything, also a new motherboard (ASUS A7Pro) with a ATA100/ATA66 cable (using both ends...)!

All I get are the usual CRC error messages.

So, there's no UDMA66 for any vt82c686a ? I'm using 2.4.3.

If there's no UDMA66, what are the advantages using this driver ?

TIA.

Signature · 6 lines
0@pervalidus.{net, {dyndns.}org} Tel: 55-21-717-2399 (Niterói-RJ BR)
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/