Could you please help me in resolving the "arch/arm/lib/vectors.S:87: Error: no such instruction: `b reset' ?"
Sir/Madam,
Could you please help me in resolving the "arch/arm/lib/vectors.S:87: Error: no such instruction: `b reset' ?"
Sincerely,
Liu Wang
liuw@liuw-SYS-E100-12T-H:~/Downloads/u-boot$ make cse_ptjob_cb3_r102_defconfig
#
# configuration written to .config
#
liuw@liuw-SYS-E100-12T-H:~/Downloads/u-boot$ make all
scripts/kconfig/conf --syncconfig Kconfig
CFG u-boot.cfg
GEN include/autoconf.mk
GEN include/autoconf.mk.dep
UPD include/generated/timestamp_autogenerated.h
HOSTCC tools/mkenvimage.o
HOSTLD tools/mkenvimage
HOSTCC tools/dumpimage.o
HOSTLD tools/dumpimage
HOSTCC tools/mkimage.o
HOSTLD tools/mkimage
LD arch/arm/cpu/built-in.o
LD arch/arm/cpu//built-in.o
AS arch/arm/lib/vectors.o
arch/arm/lib/vectors.S: Assembler messages:
arch/arm/lib/vectors.S:87: Error: no such instruction: `b reset'
arch/arm/lib/vectors.S:87: Error: no such instruction: `ldr pc,_undefined_instruction'
arch/arm/lib/vectors.S:87: Error: no such instruction: `ldr pc,_software_interrupt'
arch/arm/lib/vectors.S:87: Error: no such instruction: `ldr pc,_prefetch_abort'
arch/arm/lib/vectors.S:87: Error: no such instruction: `ldr pc,_data_abort'
arch/arm/lib/vectors.S:87: Error: no such instruction: `ldr pc,_not_used'
arch/arm/lib/vectors.S:87: Error: no such instruction: `ldr pc,_irq'
arch/arm/lib/vectors.S:87: Error: no such instruction: `ldr pc,_fiq'
arch/arm/lib/vectors.S:153: Warning: value 0x000000000badc0de truncated to 0x000000000000c0de
arch/arm/lib/vectors.S:156: Error: junk at end of line, first unrecognized character is `@'
arch/arm/lib/vectors.S:157: Error: junk at end of line, first unrecognized character is `@'
arch/arm/lib/vectors.S:158: Error: junk at end of line, first unrecognized character is `@'
arch/arm/lib/vectors.S:237: Error: Bad parameter list for macro `get_irq_stack'
arch/arm/lib/vectors.S:241: Error: Bad parameter list for macro `get_fiq_stack'
arch/arm/lib/vectors.S:249: Error: alignment not a power of 2
arch/arm/lib/vectors.S:251: Error: no such instruction: `ldr r13,IRQ_STACK_START_IN@setup our mode stack'
arch/arm/lib/vectors.S:251: Error: too many memory references for `str'
arch/arm/lib/vectors.S:251: Error: no such instruction: `mrs lr,spsr@get the spsr'
arch/arm/lib/vectors.S:251: Error: too many memory references for `str'
arch/arm/lib/vectors.S:251: Error: expecting operand after ','; got nothing
arch/arm/lib/vectors.S:251: Error: junk at end of line, first unrecognized character is `@'
arch/arm/lib/vectors.S:251: Error: no such instruction: `msr spsr,r13@switch modes,make sure moves will execute'
arch/arm/lib/vectors.S:251: Error: too many memory references for `mov'
arch/arm/lib/vectors.S:251: Warning: `pc' is not valid here (expected `(%rsi)')
arch/arm/lib/vectors.S:251: Error: junk `@jump to next instruction&switch modes.' after expression
arch/arm/lib/vectors.S:251: Warning: `lr@jump to next instruction&switch modes.' is not valid here (expected `(%rdi)')
arch/arm/lib/vectors.S:251: Warning: no instruction mnemonic suffix given and no register operands; using default for `movs'
arch/arm/lib/vectors.S:252: Error: junk at end of line, first unrecognized character is `@'
arch/arm/lib/vectors.S:252: Error: too many memory references for `sub'
arch/arm/lib/vectors.S:252: Error: no such instruction: `stmia sp,{r0 - r12}@Save user registers (now in svc mode)r0-r12'
arch/arm/lib/vectors.S:252: Error: no such instruction: `ldr r2,IRQ_STACK_START_IN'
arch/arm/lib/vectors.S:252: Error: junk at end of line, first unrecognized character is `@'
arch/arm/lib/vectors.S:252: Error: no such instruction: `ldmia r2,{r2 - r3}'
arch/arm/lib/vectors.S:252: Error: too many memory references for `add'
arch/arm/lib/vectors.S:252: Error: too many memory references for `add'
arch/arm/lib/vectors.S:252: Error: too many memory references for `mov'
arch/arm/lib/vectors.S:252: Error: no such instruction: `stmia r5,{r0 - r3}@save sp_SVC,lr_SVC,pc,cpsr'
arch/arm/lib/vectors.S:252: Error: too many memory references for `mov'
arch/arm/lib/vectors.S:253: Error: no such instruction: `bl do_undefined_instruction'
arch/arm/lib/vectors.S:255: Error: alignment not a power of 2
arch/arm/lib/vectors.S:257: Error: no such instruction: `ldr r13,IRQ_STACK_START_IN@setup our mode stack'
arch/arm/lib/vectors.S:257: Error: too many memory references for `str'
arch/arm/lib/vectors.S:257: Error: no such instruction: `mrs lr,spsr@get the spsr'
arch/arm/lib/vectors.S:257: Error: too many memory references for `str'
arch/arm/lib/vectors.S:257: Error: expecting operand after ','; got nothing
arch/arm/lib/vectors.S:257: Error: junk at end of line, first unrecognized character is `@'
arch/arm/lib/vectors.S:257: Error: no such instruction: `msr spsr,r13@switch modes,make sure moves will execute'
arch/arm/lib/vectors.S:257: Error: too many memory references for `mov'
arch/arm/lib/vectors.S:257: Warning: `pc' is not valid here (expected `(%rsi)')
arch/arm/lib/vectors.S:257: Error: junk `@jump to next instruction&switch modes.' after expression
arch/arm/lib/vectors.S:257: Warning: `lr@jump to next instruction&switch modes.' is not valid here (expected `(%rdi)')
arch/arm/lib/vectors.S:257: Warning: no instruction mnemonic suffix given and no register operands; using default for `movs'
arch/arm/lib/vectors.S:258: Error: junk at end of line, first unrecognized character is `@'
arch/arm/lib/vectors.S:258: Error: too many memory references for `sub'
arch/arm/lib/vectors.S:258: Error: no such instruction: `stmia sp,{r0 - r12}@Save user registers (now in svc mode)r0-r12'
arch/arm/lib/vectors.S:258: Error: no such instruction: `ldr r2,IRQ_STACK_START_IN'
arch/arm/lib/vectors.S:258: Error: junk at end of line, first unrecognized character is `@'
arch/arm/lib/vectors.S:258: Error: no such instruction: `ldmia r2,{r2 - r3}'
arch/arm/lib/vectors.S:258: Error: too many memory references for `add'
arch/arm/lib/vectors.S:258: Error: too many memory references for `add'
arch/arm/lib/vectors.S:258: Error: too many memory references for `mov'
arch/arm/lib/vectors.S:258: Error: no such instruction: `stmia r5,{r0 - r3}@save sp_SVC,lr_SVC,pc,cpsr'
arch/arm/lib/vectors.S:258: Error: too many memory references for `mov'
arch/arm/lib/vectors.S:259: Error: no such instruction: `bl do_software_interrupt'
arch/arm/lib/vectors.S:261: Error: alignment not a power of 2
arch/arm/lib/vectors.S:263: Error: no such instruction: `ldr r13,IRQ_STACK_START_IN@setup our mode stack'
arch/arm/lib/vectors.S:263: Error: too many memory references for `str'
arch/arm/lib/vectors.S:263: Error: no such instruction: `mrs lr,spsr@get the spsr'
arch/arm/lib/vectors.S:263: Error: too many memory references for `str'
arch/arm/lib/vectors.S:263: Error: expecting operand after ','; got nothing
arch/arm/lib/vectors.S:263: Error: junk at end of line, first unrecognized character is `@'
arch/arm/lib/vectors.S:263: Error: no such instruction: `msr spsr,r13@switch modes,make sure moves will execute'
arch/arm/lib/vectors.S:263: Error: too many memory references for `mov'
arch/arm/lib/vectors.S:263: Warning: `pc' is not valid here (expected `(%rsi)')
arch/arm/lib/vectors.S:263: Error: junk `@jump to next instruction&switch modes.' after expression
arch/arm/lib/vectors.S:263: Warning: `lr@jump to next instruction&switch modes.' is not valid here (expected `(%rdi)')
arch/arm/lib/vectors.S:263: Warning: no instruction mnemonic suffix given and no register operands; using default for `movs'
arch/arm/lib/vectors.S:264: Error: junk at end of line, first unrecognized character is `@'
arch/arm/lib/vectors.S:264: Error: too many memory references for `sub'
arch/arm/lib/vectors.S:264: Error: no such instruction: `stmia sp,{r0 - r12}@Save user registers (now in svc mode)r0-r12'
arch/arm/lib/vectors.S:264: Error: no such instruction: `ldr r2,IRQ_STACK_START_IN'
arch/arm/lib/vectors.S:264: Error: junk at end of line, first unrecognized character is `@'
arch/arm/lib/vectors.S:264: Error: no such instruction: `ldmia r2,{r2 - r3}'
arch/arm/lib/vectors.S:264: Error: too many memory references for `add'
arch/arm/lib/vectors.S:264: Error: too many memory references for `add'
arch/arm/lib/vectors.S:264: Error: too many memory references for `mov'
arch/arm/lib/vectors.S:264: Error: no such instruction: `stmia r5,{r0 - r3}@save sp_SVC,lr_SVC,pc,cpsr'
arch/arm/lib/vectors.S:264: Error: too many memory references for `mov'
arch/arm/lib/vectors.S:265: Error: no such instruction: `bl do_prefetch_abort'
arch/arm/lib/vectors.S:267: Error: alignment not a power of 2
arch/arm/lib/vectors.S:269: Error: no such instruction: `ldr r13,IRQ_STACK_START_IN@setup our mode stack'
arch/arm/lib/vectors.S:269: Error: too many memory references for `str'
arch/arm/lib/vectors.S:269: Error: no such instruction: `mrs lr,spsr@get the spsr'
arch/arm/lib/vectors.S:269: Error: too many memory references for `str'
arch/arm/lib/vectors.S:269: Error: expecting operand after ','; got nothing
arch/arm/lib/vectors.S:269: Error: junk at end of line, first unrecognized character is `@'
arch/arm/lib/vectors.S:269: Error: no such instruction: `msr spsr,r13@switch modes,make sure moves will execute'
arch/arm/lib/vectors.S:269: Error: too many memory references for `mov'
arch/arm/lib/vectors.S:269: Warning: `pc' is not valid here (expected `(%rsi)')
arch/arm/lib/vectors.S:269: Error: junk `@jump to next instruction&switch modes.' after expression
arch/arm/lib/vectors.S:269: Warning: `lr@jump to next instruction&switch modes.' is not valid here (expected `(%rdi)')
arch/arm/lib/vectors.S:269: Warning: no instruction mnemonic suffix given and no register operands; using default for `movs'
arch/arm/lib/vectors.S:270: Error: junk at end of line, first unrecognized character is `@'
arch/arm/lib/vectors.S:270: Error: too many memory references for `sub'
arch/arm/lib/vectors.S:270: Error: no such instruction: `stmia sp,{r0 - r12}@Save user registers (now in svc mode)r0-r12'
arch/arm/lib/vectors.S:270: Error: no such instruction: `ldr r2,IRQ_STACK_START_IN'
arch/arm/lib/vectors.S:270: Error: junk at end of line, first unrecognized character is `@'
arch/arm/lib/vectors.S:270: Error: no such instruction: `ldmia r2,{r2 - r3}'
arch/arm/lib/vectors.S:270: Error: too many memory references for `add'
arch/arm/lib/vectors.S:270: Error: too many memory references for `add'
arch/arm/lib/vectors.S:270: Error: too many memory references for `mov'
arch/arm/lib/vectors.S:270: Error: no such instruction: `stmia r5,{r0 - r3}@save sp_SVC,lr_SVC,pc,cpsr'
arch/arm/lib/vectors.S:270: Error: too many memory references for `mov'
arch/arm/lib/vectors.S:271: Error: no such instruction: `bl do_data_abort'
arch/arm/lib/vectors.S:273: Error: alignment not a power of 2
arch/arm/lib/vectors.S:275: Error: no such instruction: `ldr r13,IRQ_STACK_START_IN@setup our mode stack'
arch/arm/lib/vectors.S:275: Error: too many memory references for `str'
arch/arm/lib/vectors.S:275: Error: no such instruction: `mrs lr,spsr@get the spsr'
arch/arm/lib/vectors.S:275: Error: too many memory references for `str'
arch/arm/lib/vectors.S:275: Error: expecting operand after ','; got nothing
arch/arm/lib/vectors.S:275: Error: junk at end of line, first unrecognized character is `@'
arch/arm/lib/vectors.S:275: Error: no such instruction: `msr spsr,r13@switch modes,make sure moves will execute'
arch/arm/lib/vectors.S:275: Error: too many memory references for `mov'
arch/arm/lib/vectors.S:275: Warning: `pc' is not valid here (expected `(%rsi)')
arch/arm/lib/vectors.S:275: Error: junk `@jump to next instruction&switch modes.' after expression
arch/arm/lib/vectors.S:275: Warning: `lr@jump to next instruction&switch modes.' is not valid here (expected `(%rdi)')
arch/arm/lib/vectors.S:275: Warning: no instruction mnemonic suffix given and no register operands; using default for `movs'
arch/arm/lib/vectors.S:276: Error: junk at end of line, first unrecognized character is `@'
arch/arm/lib/vectors.S:276: Error: too many memory references for `sub'
arch/arm/lib/vectors.S:276: Error: no such instruction: `stmia sp,{r0 - r12}@Save user registers (now in svc mode)r0-r12'
arch/arm/lib/vectors.S:276: Error: no such instruction: `ldr r2,IRQ_STACK_START_IN'
arch/arm/lib/vectors.S:276: Error: junk at end of line, first unrecognized character is `@'
arch/arm/lib/vectors.S:276: Error: no such instruction: `ldmia r2,{r2 - r3}'
arch/arm/lib/vectors.S:276: Error: too many memory references for `add'
arch/arm/lib/vectors.S:276: Error: too many memory references for `add'
arch/arm/lib/vectors.S:276: Error: too many memory references for `mov'
arch/arm/lib/vectors.S:276: Error: no such instruction: `stmia r5,{r0 - r3}@save sp_SVC,lr_SVC,pc,cpsr'
arch/arm/lib/vectors.S:276: Error: too many memory references for `mov'
arch/arm/lib/vectors.S:277: Error: no such instruction: `bl do_not_used'
arch/arm/lib/vectors.S:280: Error: alignment not a power of 2
arch/arm/lib/vectors.S:282: Error: no such instruction: `ldr r13,IRQ_STACK_START_IN@setup our mode stack'
arch/arm/lib/vectors.S:282: Error: too many memory references for `str'
arch/arm/lib/vectors.S:282: Error: no such instruction: `mrs lr,spsr@get the spsr'
arch/arm/lib/vectors.S:282: Error: too many memory references for `str'
arch/arm/lib/vectors.S:282: Error: expecting operand after ','; got nothing
arch/arm/lib/vectors.S:282: Error: junk at end of line, first unrecognized character is `@'
arch/arm/lib/vectors.S:282: Error: no such instruction: `msr spsr,r13@switch modes,make sure moves will execute'
arch/arm/lib/vectors.S:282: Error: too many memory references for `mov'
arch/arm/lib/vectors.S:282: Warning: `pc' is not valid here (expected `(%rsi)')
arch/arm/lib/vectors.S:282: Error: junk `@jump to next instruction&switch modes.' after expression
arch/arm/lib/vectors.S:282: Warning: `lr@jump to next instruction&switch modes.' is not valid here (expected `(%rdi)')
arch/arm/lib/vectors.S:282: Warning: no instruction mnemonic suffix given and no register operands; using default for `movs'
arch/arm/lib/vectors.S:283: Error: junk at end of line, first unrecognized character is `@'
arch/arm/lib/vectors.S:283: Error: too many memory references for `sub'
arch/arm/lib/vectors.S:283: Error: no such instruction: `stmia sp,{r0 - r12}@Save user registers (now in svc mode)r0-r12'
arch/arm/lib/vectors.S:283: Error: no such instruction: `ldr r2,IRQ_STACK_START_IN'
arch/arm/lib/vectors.S:283: Error: junk at end of line, first unrecognized character is `@'
arch/arm/lib/vectors.S:283: Error: no such instruction: `ldmia r2,{r2 - r3}'
arch/arm/lib/vectors.S:283: Error: too many memory references for `add'
arch/arm/lib/vectors.S:283: Error: too many memory references for `add'
arch/arm/lib/vectors.S:283: Error: too many memory references for `mov'
arch/arm/lib/vectors.S:283: Error: no such instruction: `stmia r5,{r0 - r3}@save sp_SVC,lr_SVC,pc,cpsr'
arch/arm/lib/vectors.S:283: Error: too many memory references for `mov'
arch/arm/lib/vectors.S:284: Error: no such instruction: `bl do_irq'
arch/arm/lib/vectors.S:286: Error: alignment not a power of 2
arch/arm/lib/vectors.S:288: Error: no such instruction: `ldr r13,IRQ_STACK_START_IN@setup our mode stack'
arch/arm/lib/vectors.S:288: Error: too many memory references for `str'
arch/arm/lib/vectors.S:288: Error: no such instruction: `mrs lr,spsr@get the spsr'
arch/arm/lib/vectors.S:288: Error: too many memory references for `str'
arch/arm/lib/vectors.S:288: Error: expecting operand after ','; got nothing
arch/arm/lib/vectors.S:288: Error: junk at end of line, first unrecognized character is `@'
arch/arm/lib/vectors.S:288: Error: no such instruction: `msr spsr,r13@switch modes,make sure moves will execute'
arch/arm/lib/vectors.S:288: Error: too many memory references for `mov'
arch/arm/lib/vectors.S:288: Warning: `pc' is not valid here (expected `(%rsi)')
arch/arm/lib/vectors.S:288: Error: junk `@jump to next instruction&switch modes.' after expression
arch/arm/lib/vectors.S:288: Warning: `lr@jump to next instruction&switch modes.' is not valid here (expected `(%rdi)')
arch/arm/lib/vectors.S:288: Warning: no instruction mnemonic suffix given and no register operands; using default for `movs'
arch/arm/lib/vectors.S:289: Error: junk at end of line, first unrecognized character is `@'
arch/arm/lib/vectors.S:289: Error: too many memory references for `sub'
arch/arm/lib/vectors.S:289: Error: no such instruction: `stmia sp,{r0 - r12}@Save user registers (now in svc mode)r0-r12'
arch/arm/lib/vectors.S:289: Error: no such instruction: `ldr r2,IRQ_STACK_START_IN'
arch/arm/lib/vectors.S:289: Error: junk at end of line, first unrecognized character is `@'
arch/arm/lib/vectors.S:289: Error: no such instruction: `ldmia r2,{r2 - r3}'
arch/arm/lib/vectors.S:289: Error: too many memory references for `add'
arch/arm/lib/vectors.S:289: Error: too many memory references for `add'
arch/arm/lib/vectors.S:289: Error: too many memory references for `mov'
arch/arm/lib/vectors.S:289: Error: no such instruction: `stmia r5,{r0 - r3}@save sp_SVC,lr_SVC,pc,cpsr'
arch/arm/lib/vectors.S:289: Error: too many memory references for `mov'
arch/arm/lib/vectors.S:290: Error: no such instruction: `bl do_fiq'
arch/arm/lib/vectors.S:120: Error: alignment padding (2 bytes) not a multiple of 4
arch/arm/lib/vectors.S:120: Error: alignment padding (2 bytes) not a multiple of 4
make[1]: *** [scripts/Makefile.build:301: arch/arm/lib/vectors.o] Error 1
make: *** [Makefile:1780: arch/arm/lib] Error 2
liuw@liuw-SYS-E100-12T-H:~/Downloads/u-bootQuoted 8 lines · Liu Wang
Sir/Madam,
Could you please help me in resolving the "
arch/arm/lib/vectors.S:87: Error: no such instruction: `b reset' ?"Sincerely,
Liu Wangliuw@liuw-SYS-E100-12T-H:~/Downloads/u-boot$ make cse_ptjob_cb3_r102_defconfig
This is not a configuration supported by U-Boot mainline.
Quoted 12 lines
#
# configuration written to .config # liuw@liuw-SYS-E100-12T-H:~/Downloads/u-boot$ make all scripts/kconfig/conf --syncconfig Kconfig CFG u-boot.cfg GEN include/autoconf.mk GEN include/autoconf.mk.dep UPD include/generated/timestamp_autogenerated.h HOSTCC tools/mkenvimage.o HOSTLD tools/mkenvimage HOSTCC tools/dumpimage.o
Quoted 8 lines
HOSTLD tools/dumpimage HOSTCC tools/mkimage.o HOSTLD tools/mkimage LD arch/arm/cpu/built-in.o LD arch/arm/cpu//built-in.o AS arch/arm/lib/vectors.o arch/arm/lib/vectors.S: Assembler messages: arch/arm/lib/vectors.S:87: Error: no such instruction: `b reset'
Have you exported the toolchain?
Hi Fabio,
Thank you for your help.
1. You are right. It is not an U-boot mainline configuration.
I am porting U-boot to our company's hardware platform https://www.supermicro.com/manuals/other/CSE-PTJBOD-CB3.pdf with SoC AST2400 from Aspeed embedded with an ARM core ARM926EJ 32-bit RISC CPU.
2. You are right. I have not exported the tool chain.
Could you please share me a link to a readme in setting up the tool chain for Ubuntu cross build environment ?
Sincerely,
Liu Wang
-----Original Message-----
From: Fabio Estevam <[email protected]>
Sent: Wednesday, January 17, 2024 6:06 AM
To: Liu Wang (HW) <[email protected]>
Cc: [email protected]
Subject: Re: Could you please help me in resolving the "arch/arm/lib/vectors.S:87: Error: no such instruction: `b reset' ?"
[CAUTION: External Mail]
Quoted 8 lines · Liu Wang
Sir/Madam,
Could you please help me in resolving the "
arch/arm/lib/vectors.S:87: Error: no such instruction: `b reset' ?"Sincerely,
Liu Wangliuw@liuw-SYS-E100-12T-H:~/Downloads/u-boot$ make cse_ptjob_cb3_r102_defconfig
This is not a configuration supported by U-Boot mainline.
Quoted 12 lines
#
# configuration written to .config # liuw@liuw-SYS-E100-12T-H:~/Downloads/u-boot$ make all scripts/kconfig/conf --syncconfig Kconfig CFG u-boot.cfg GEN include/autoconf.mk GEN include/autoconf.mk.dep UPD include/generated/timestamp_autogenerated.h HOSTCC tools/mkenvimage.o HOSTLD tools/mkenvimage HOSTCC tools/dumpimage.o
Quoted 8 lines
HOSTLD tools/dumpimage HOSTCC tools/mkimage.o HOSTLD tools/mkimage LD arch/arm/cpu/built-in.o LD arch/arm/cpu//built-in.o AS arch/arm/lib/vectors.o arch/arm/lib/vectors.S: Assembler messages: arch/arm/lib/vectors.S:87: Error: no such instruction: `b reset'
Have you exported the toolchain?
Quoted 2 lines · Liu Wang
2. You are right. I have not exported the tool chain.
Could you please share me a link to a readme in setting up the tool chain for Ubuntu cross build environment ?
You can do like this:
export ARCH=arm
export CROSS_COMPILE=/usr/bin/arm-linux-gnueabihf-
make cse_ptjob_cb3_r102_defconfig
make
Hi Fabio,
Appreciate!
Sincerely,
Liu Wang
Quoted 16 lines · Fabio Estevam
[CAUTION: External Mail]
Quoted 4 lines · Liu Wang
2. You are right. I have not exported the tool chain.
Could you please share me a link to a readme in setting up the tool chain for Ubuntu cross build environment ?You can do like this:
export ARCH=arm
export CROSS_COMPILE=/usr/bin/arm-linux-gnueabihf-make
cse_ptjob_cb3_r102_defconfig
make
Hi Fabio,
Thank you again for your help.
Run into format error after export tool chain:
...gnueabihf-gcc: cannot execute binary file: Exec format error...
Could you please share more ?
Sincerely,
Liu Wang
--------------------/bin/sh: line 1: /home/liuw/armgnutoolchain132Rel1aarch64armnonelinuxgnueabihf/arm-gnu-toolchain-13.2.Rel1-aarch64-arm-none-linux-gnueabihf/bin/arm-none-linux-gnueabihf-gcc: cannot execute binary file: Exec format error /home/liuw/armgnutoolchain132Rel1aarch64armnonelinuxgnueabihf/arm-gnu-toolchain-13.2.Rel1-aarch64-arm-none-linux-gnueabihf/bin/arm-none-linux-gnueabihf-gcc: /home/liuw/armgnutoolchain132Rel1aarch64armnonelinuxgnueabihf/arm-gnu-toolchain-13.2.Rel1-aarch64-arm-none-linux-gnueabihf/bin/arm-none-linux-gnueabihf-gcc: cannot execute binary file /bin/sh: line 1: /home/liuw/armgnutoolchain132Rel1aarch64armnonelinuxgnueabihf/arm-gnu-toolchain-13.2.Rel1-aarch64-arm-none-linux-gnueabihf/bin/arm-none-linux-gnueabihf-gcc: cannot execute binary file: Exec format error
dirname: missing operand
Try 'dirname --help' for more information./bin/sh: line 1: /home/liuw/armgnutoolchain132Rel1aarch64armnonelinuxgnueabihf/arm-gnu-toolchain-13.2.Rel1-aarch64-arm-none-linux-gnueabihf/bin/arm-none-linux-gnueabihf-gcc: cannot execute binary file: Exec format errorscripts/kconfig/conf --syncconfig Kconfig./scripts/gcc-version.sh: line 25: /home/liuw/armgnutoolchain132Rel1aarch64armnonelinuxgnueabihf/arm-gnu-toolchain-13.2.Rel1-aarch64-arm-none-linux-gnueabihf/bin/arm-none-linux-gnueabihf-gcc: cannot execute binary file: Exec format error./scripts/gcc-version.sh: line 26: /home/liuw/armgnutoolchain132Rel1aarch64armnonelinuxgnueabihf/arm-gnu-toolchain-13.2.Rel1-aarch64-arm-none-linux-gnueabihf/bin/arm-none-linux-gnueabihf-gcc: cannot execute binary file: Exec format error./scripts/gcc-version.sh: line 28: /home/liuw/armgnutoolchain132Rel1aarch64armnonelinuxgnueabihf/arm-gnu-toolchain-13.2.Rel1-aarch64-arm-none-linux-gnueabihf/bin/arm-none-linux-gnueabihf-gcc: cannot execute binary file: Exec format error
CFG u-boot.cfg/bin/sh: line 1: /home/liuw/armgnutoolchain132Rel1aarch64armnonelinuxgnueabihf/arm-gnu-toolchain-13.2.Rel1-aarch64-arm-none-linux-gnueabihf/bin/arm-none-linux-gnueabihf-gcc: cannot execute binary file: Exec format error
make[1]: *** [scripts/Makefile.autoconf:77: u-boot.cfg] Error 1
make: *** No rule to make target 'include/config/auto.conf', needed by 'include/config/uboot.release'. Stop.
-----Original Message-----
From: Liu Wang (HW) <[email protected]>
Sent: Wednesday, January 17, 2024 12:08 PM
To: Fabio Estevam <[email protected]>
Cc: [email protected]
Subject: Re: Could you please help me in resolving the "arch/arm/lib/vectors.S:87: Error: no such instruction: `b reset' ?"
Hi Fabio,
Appreciate!
Sincerely,
Liu Wang
Quoted 16 lines · Fabio Estevam
[CAUTION: External Mail]
Quoted 4 lines · Liu Wang
2. You are right. I have not exported the tool chain.
Could you please share me a link to a readme in setting up the tool chain for Ubuntu cross build environment ?You can do like this:
export ARCH=arm
export CROSS_COMPILE=/usr/bin/arm-linux-gnueabihf-make
cse_ptjob_cb3_r102_defconfig
make
Hi Fabio,
Thank you for your help.
Switching to "arm-gnu-toolchain-13.2.Rel1-x86-64-arm-none-eabi" seems a fix for :
...gnueabihf-gcc: cannot execute binary file: Exec format error...
Sincerely,
Liu Wang
---------------------------
liuw@liuw-SYS-E100-12T-H:~/Downloads/u-boot$ make
scripts/kconfig/conf
--syncconfig Kconfig
CFG u-boot.cfg
GEN
include/autoconf.mk
GEN
include/autoconf.mk.dep
UPD
include/generated/version_autogenerated.h
UPD
include/generated/timestamp_autogenerated.h
CC
lib/asm-offsets.s
UPD
include/generated/generic-asm-offsets.h
CC
arch/arm/lib/asm-offsets.s
HOSTCC
tools/mkenvimage.o
HOSTLD
tools/mkenvimage
HOSTCC
tools/aisimage.o
HOSTCC
tools/atmelimage.o
HOSTCC
tools/common/fdt_region.o
HOSTCC
tools/common/bootm.o
HOSTCC
tools/default_image.o
HOSTCC
tools/lib/fdtdec_common.o
HOSTCC
tools/lib/fdtdec.o
HOSTCC
tools/common/image.o
HOSTCC
tools/imagetool.o
HOSTCC
tools/imximage.o
HOSTCC
tools/imx8image.o
tools/imx8image.c:
In function ‘copy_file.constprop’:
tools/imx8image.c:414:21:
warning: ‘write’ reading 5 bytes from a region of size 4
[-Wstringop-overread]
414 |
if (write(ifd, (char *)&zero, 4 - tail) != 4 - tail) {
|
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
tools/imx8image.c:368:13:
note: source object ‘zero’ of size 4
368 | int
zero = 0;
|
^~~~
In file included
from ./tools/imagetool.h:21,from include/imx8image.h:13,
from tools/imx8image.c:8:/usr/include/unistd.h:378:16:
note: in a call to function ‘write’ declared with attribute ‘access (read_only, 2, 3)’
378 | externssize_t write (int __fd, const void *__buf, size_t __n) __wur
|
^~~~~
HOSTCCtools/imx8mimage.otools/imx8mimage.c:
In function ‘copy_file.constprop’:tools/imx8mimage.c:291:21:
warning: ‘write’ reading 5 bytes from a region of size 4 [-Wstringop-overread]
291 |
if (write(ifd, (char *)&zero, 4 - tail) != 4 - tail) {
|
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
tools/imx8mimage.c:249:13:
note: source object ‘zero’ of size 4
249 | int
zero = 0;
| ^~~~
In file included
from tools/imagetool.h:21,
from tools/imx8mimage.c:9:/usr/include/unistd.h:378:16:
note: in a call to function ‘write’ declared with attribute ‘access (read_only, 2, 3)’
378 | externssize_t write (int __fd, const void *__buf, size_t __n) __wur
|
^~~~~
HOSTCCtools/kwbimage.o
HOSTCCtools/lpc32xximage.o
HOSTCCtools/omapimage.o
HOSTCCtools/pblimage.o
HOSTCCtools/vybridimage.o
HOSTCCtools/stm32image.o
HOSTCCtools/rkcommon.o
HOSTCCtools/rkimage.o
HOSTCCtools/rksd.o
HOSTCCtools/rkspi.o
HOSTCCtools/socfpgaimage.o
HOSTCCtools/common/hash.o
HOSTCCtools/ublimage.o
HOSTCCtools/zynqimage.o
HOSTCCtools/zynqmpimage.o
HOSTCCtools/zynqmpbif.o
HOSTCCtools/libfdt/fdt.o
HOSTCCtools/libfdt/fdt_ro.o
HOSTCCtools/libfdt/fdt_wip.o
HOSTCCtools/libfdt/fdt_sw.o
HOSTCCtools/libfdt/fdt_rw.o
HOSTCCtools/libfdt/fdt_strerror.o
HOSTCCtools/libfdt/fdt_empty_tree.o
HOSTCCtools/libfdt/fdt_addresses.o
HOSTCCtools/libfdt/fdt_overlay.o
HOSTCCtools/gpimage.o
HOSTCCtools/gpimage-common.o
HOSTCCtools/mtk_image.o
HOSTCCtools/dumpimage.o
HOSTLDtools/dumpimage
HOSTCCtools/mkimage.o
HOSTLDtools/mkimage
HOSTCCtools/fdtgrep.o
HOSTLDtools/fdtgrep
HOSTCCtools/spl_size_limit
LDarch/arm/cpu/built-in.o
LD
arch/arm/cpu//built-in.o
ASarch/arm/lib/vectors.o
ASarch/arm/lib/crt0.o
ASarch/arm/lib/setjmp.o
ASarch/arm/lib/relocate.o
CCarch/arm/lib/bootm-fdt.o
CCarch/arm/lib/bootm.o
In file included
from ./arch/arm/include/asm/system.h:5,
from ./arch/arm/include/asm/cache.h:11,
from arch/arm/lib/bootm.c:35:./arch/arm/include/asm/barriers.h:32:24:
error: operator '>=' has no left operand
32 | #if__LINUX_ARM_ARCH__ >= 7
|
^~./arch/arm/include/asm/barriers.h:36:26:
error: operator '==' has no left operand
36 | #elif__LINUX_ARM_ARCH__ == 6
|
^~make[1]: ***
[scripts/Makefile.build:266: arch/arm/lib/bootm.o] Error 1
make: ***
[Makefile:1780: arch/arm/lib] Error 2 liuw@liuw-SYS-E100-12T-H:~/Downloads/u-boot$
-----Original Message-----
From: Liu Wang (HW)
Sent: Wednesday, January 17, 2024 4:08 PM
To: Fabio Estevam <[email protected]>
Cc: [email protected]
Subject: RE: Could you please help me in resolving the "arch/arm/lib/vectors.S:87: Error: no such instruction: `b reset' ?"
Hi Fabio,
Thank you again for your help.
Run into format error after export tool chain:
...gnueabihf-gcc: cannot execute binary file: Exec format error...
Could you please share more ?
Sincerely,
Liu Wang
--------------------/bin/sh: line 1: /home/liuw/armgnutoolchain132Rel1aarch64armnonelinuxgnueabihf/arm-gnu-toolchain-13.2.Rel1-aarch64-arm-none-linux-gnueabihf/bin/arm-none-linux-gnueabihf-gcc: cannot execute binary file: Exec format error /home/liuw/armgnutoolchain132Rel1aarch64armnonelinuxgnueabihf/arm-gnu-toolchain-13.2.Rel1-aarch64-arm-none-linux-gnueabihf/bin/arm-none-linux-gnueabihf-gcc: /home/liuw/armgnutoolchain132Rel1aarch64armnonelinuxgnueabihf/arm-gnu-toolchain-13.2.Rel1-aarch64-arm-none-linux-gnueabihf/bin/arm-none-linux-gnueabihf-gcc: cannot execute binary file /bin/sh: line 1: /home/liuw/armgnutoolchain132Rel1aarch64armnonelinuxgnueabihf/arm-gnu-toolchain-13.2.Rel1-aarch64-arm-none-linux-gnueabihf/bin/arm-none-linux-gnueabihf-gcc: cannot execute binary file: Exec format error
dirname: missing operand
Try 'dirname --help' for more information./bin/sh: line 1: /home/liuw/armgnutoolchain132Rel1aarch64armnonelinuxgnueabihf/arm-gnu-toolchain-13.2.Rel1-aarch64-arm-none-linux-gnueabihf/bin/arm-none-linux-gnueabihf-gcc: cannot execute binary file: Exec format errorscripts/kconfig/conf --syncconfig Kconfig./scripts/gcc-version.sh: line 25: /home/liuw/armgnutoolchain132Rel1aarch64armnonelinuxgnueabihf/arm-gnu-toolchain-13.2.Rel1-aarch64-arm-none-linux-gnueabihf/bin/arm-none-linux-gnueabihf-gcc: cannot execute binary file: Exec format error./scripts/gcc-version.sh: line 26: /home/liuw/armgnutoolchain132Rel1aarch64armnonelinuxgnueabihf/arm-gnu-toolchain-13.2.Rel1-aarch64-arm-none-linux-gnueabihf/bin/arm-none-linux-gnueabihf-gcc: cannot execute binary file: Exec format error./scripts/gcc-version.sh: line 28: /home/liuw/armgnutoolchain132Rel1aarch64armnonelinuxgnueabihf/arm-gnu-toolchain-13.2.Rel1-aarch64-arm-none-linux-gnueabihf/bin/arm-none-linux-gnueabihf-gcc: cannot execute binary file: Exec format error
CFG u-boot.cfg/bin/sh: line 1: /home/liuw/armgnutoolchain132Rel1aarch64armnonelinuxgnueabihf/arm-gnu-toolchain-13.2.Rel1-aarch64-arm-none-linux-gnueabihf/bin/arm-none-linux-gnueabihf-gcc: cannot execute binary file: Exec format error
make[1]: *** [scripts/Makefile.autoconf:77: u-boot.cfg] Error 1
make: *** No rule to make target 'include/config/auto.conf', needed by 'include/config/uboot.release'. Stop.
-----Original Message-----
From: Liu Wang (HW) <[email protected]>
Sent: Wednesday, January 17, 2024 12:08 PM
To: Fabio Estevam <[email protected]>
Cc: [email protected]
Subject: Re: Could you please help me in resolving the "arch/arm/lib/vectors.S:87: Error: no such instruction: `b reset' ?"
Hi Fabio,
Appreciate!
Sincerely,
Liu Wang
Quoted 16 lines · Fabio Estevam
[CAUTION: External Mail]
Quoted 4 lines · Liu Wang
2. You are right. I have not exported the tool chain.
Could you please share me a link to a readme in setting up the tool chain for Ubuntu cross build environment ?You can do like this:
export ARCH=arm
export CROSS_COMPILE=/usr/bin/arm-linux-gnueabihf-make
cse_ptjob_cb3_r102_defconfig
make
Quoted 7 lines · Liu Wang
Hi Fabio,
Thank you for your help.
Switching to "arm-gnu-toolchain-13.2.Rel1-x86-64-arm-none-eabi" seems a fix for :
...gnueabihf-gcc: cannot execute binary file: Exec format error...
I would suggest installing the default arm toolchain from Ubuntu.
As for the build error, you would need to ask to whoever provided you with the code.
Since this is not a mainline U-Boot, we cannot help.
Hi Fabio,
Thank you.
Will do.
Sincerely,
Liu Wang
Quoted 19 lines · Fabio Estevam
[CAUTION: External Mail]
Quoted 8 lines · Liu Wang
Hi Fabio,
Thank you for your help.
Switching to "arm-gnu-toolchain-13.2.Rel1-x86-64-arm-none-eabi" seems a fix for :
...gnueabihf-gcc: cannot execute binary file: Exec format error...I would suggest installing the default arm toolchain from Ubuntu.
As for the build error, you would need to ask to whoever provided you with the code.
Since this is not a mainline U-Boot, we cannot help.
Could you please help me in resolving the " /reset.c:42:(.text.do_reset+0x20): undefined reference to `reset_cpu'?"
Hi Fabio,
Could you please help me in resolving the " /reset.c:42:(.text.do_reset+0x20): undefined reference to `reset_cpu'?" from: u-boot$make all:
Sincerely,
Liu Wang
----------------------------------------------------------------------
...$make all
UPD include/generated/timestamp_autogenerated.h HOSTCC tools/mkenvimage.o HOSTLD tools/mkenvimage HOSTCC tools/dumpimage.o HOSTLD tools/dumpimage HOSTCC tools/mkimage.o HOSTLD tools/mkimage CC cmd/version.o LD cmd/built-in.o CC common/main.o LD common/built-in.o CC lib/display_options.o LD lib/built-in.o LD u-boot
/home/liuw/armgnutoolchain132rel1x8664armnoneeabi/arm-gnu-toolchain-13.2.Rel1-x86_64-arm-none-eabi/bin/arm-none-eabi-ld.bfd: warning: u-boot has a LOAD segment with RWX permissions /home/liuw/armgnutoolchain132rel1x8664armnoneeabi/arm-gnu-toolchain-13.2.Rel1-x86_64-arm-none-eabi/bin/arm-none-eabi-ld.bfd: arch/arm/lib/built-in.o: in function `do_reset':
/home/liuw/Downloads/u-boot/arch/arm/lib/reset.c:42:(.text.do_reset+0x20): undefined reference to `reset_cpu'/home/liuw/armgnutoolchain132rel1x8664armnoneeabi/arm-gnu-toolchain-13.2.Rel1-x86_64-arm-none-eabi/bin/arm-none-eabi-ld.bfd: arch/arm/mach-aspeed/built-in.o: in function `dram_init':
/home/liuw/Downloads/u-boot/arch/arm/mach-aspeed/ast2500/board_common.c:50:(.text.dram_init+0x24): undefined reference to ram_get_info' /home/liuw/armgnutoolchain132rel1x8664armnoneeabi/arm-gnu-toolchain-13.2.Rel1-x86_64-arm-none-eabi/bin/arm-none-eabi-ld.bfd: arch/arm/mach-aspeed/built-in.o: in function ast2500_sdrammc_ofdata_to_platdata':
/home/liuw/Downloads/u-boot/arch/arm/mach-aspeed/ast2500/sdram_ast2500.c:395:(.text.ast2500_sdrammc_ofdata_to_platdata+0x18): undefined reference to `regmap_init_mem' /home/liuw/armgnutoolchain132rel1x8664armnoneeabi/arm-gnu-toolchain-13.2.Rel1-x86_64-arm-none-eabi/bin/arm-none-eabi-ld.bfd: /home/liuw/Downloads/u-boot/arch/arm/mach-aspeed/ast2500/sdram_ast2500.c:399:(.text.ast2500_sdrammc_ofdata_to_platdata+0x2c): undefined reference to `regmap_get_range' /home/liuw/armgnutoolchain132rel1x8664armnoneeabi/arm-gnu-toolchain-13.2.Rel1-x86_64-arm-none-eabi/bin/arm-none-eabi-ld.bfd: /home/liuw/Downloads/u-boot/arch/arm/mach-aspeed/ast2500/sdram_ast2500.c:400:(.text.ast2500_sdrammc_ofdata_to_platdata+0x3c): undefined reference to regmap_get_range' /home/liuw/armgnutoolchain132rel1x8664armnoneeabi/arm-gnu-toolchain-13.2.Rel1-x86_64-arm-none-eabi/bin/arm-none-eabi-ld.bfd: cmd/built-in.o: in function do_imls_nor':
/home/liuw/Downloads/u-boot/cmd/bootm.c:390:(.text.do_imls+0x9c): undefined reference to `flash_info'/home/liuw/armgnutoolchain132rel1x8664armnoneeabi/arm-gnu-toolchain-13.2.Rel1-x86_64-arm-none-eabi/bin/arm-none-eabi-ld.bfd: cmd/built-in.o: in function `do_i2c_reset':
/home/liuw/Downloads/u-boot/cmd/i2c.c:1960:(.text.do_i2c_reset+0xc): undefined reference to `i2c_init'/home/liuw/armgnutoolchain132rel1x8664armnoneeabi/arm-gnu-toolchain-13.2.Rel1-x86_64-arm-none-eabi/bin/arm-none-eabi-ld.bfd: cmd/built-in.o: in function `do_i2c_probe':
/home/liuw/Downloads/u-boot/cmd/i2c.c:999:(.text.do_i2c_probe+0x5c): undefined reference to `i2c_probe'/home/liuw/armgnutoolchain132rel1x8664armnoneeabi/arm-gnu-toolchain-13.2.Rel1-x86_64-arm-none-eabi/bin/arm-none-eabi-ld.bfd: cmd/built-in.o: in function `do_i2c_md':
/home/liuw/Downloads/u-boot/cmd/i2c.c:592:(.text.do_i2c_md+0xd0): undefined reference to `i2c_read'/home/liuw/armgnutoolchain132rel1x8664armnoneeabi/arm-gnu-toolchain-13.2.Rel1-x86_64-arm-none-eabi/bin/arm-none-eabi-ld.bfd: cmd/built-in.o: in function `do_i2c_read':
/home/liuw/Downloads/u-boot/cmd/i2c.c:342:(.text.do_i2c_read+0x90): undefined reference to `i2c_read'/home/liuw/armgnutoolchain132rel1x8664armnoneeabi/arm-gnu-toolchain-13.2.Rel1-x86_64-arm-none-eabi/bin/arm-none-eabi-ld.bfd: cmd/built-in.o: in function `do_i2c_mw':
/home/liuw/Downloads/u-boot/cmd/i2c.c:691:(.text.do_i2c_mw+0xc8): undefined reference to `i2c_write'/home/liuw/armgnutoolchain132rel1x8664armnoneeabi/arm-gnu-toolchain-13.2.Rel1-x86_64-arm-none-eabi/bin/arm-none-eabi-ld.bfd: cmd/built-in.o: in function `do_i2c_write':
/home/liuw/Downloads/u-boot/cmd/i2c.c:426:(.text.do_i2c_write+0xc8): undefined reference to `i2c_write'/home/liuw/armgnutoolchain132rel1x8664armnoneeabi/arm-gnu-toolchain-13.2.Rel1-x86_64-arm-none-eabi/bin/arm-none-eabi-ld.bfd: /home/liuw/Downloads/u-boot/cmd/i2c.c:412:(.text.do_i2c_write+0x110): undefined reference to i2c_write' /home/liuw/armgnutoolchain132rel1x8664armnoneeabi/arm-gnu-toolchain-13.2.Rel1-x86_64-arm-none-eabi/bin/arm-none-eabi-ld.bfd: cmd/built-in.o: in function do_i2c_crc':
/home/liuw/Downloads/u-boot/cmd/i2c.c:779:(.text.do_i2c_crc+0xd4): undefined reference to `i2c_read'/home/liuw/armgnutoolchain132rel1x8664armnoneeabi/arm-gnu-toolchain-13.2.Rel1-x86_64-arm-none-eabi/bin/arm-none-eabi-ld.bfd: cmd/built-in.o: in function `mod_i2c_mem':
/home/liuw/Downloads/u-boot/cmd/i2c.c:874:(.text.mod_i2c_mem.isra.0+0xbc): undefined reference to `i2c_read'/home/liuw/armgnutoolchain132rel1x8664armnoneeabi/arm-gnu-toolchain-13.2.Rel1-x86_64-arm-none-eabi/bin/arm-none-eabi-ld.bfd: /home/liuw/Downloads/u-boot/cmd/i2c.c:922:(.text.mod_i2c_mem.isra.0+0x1d0): undefined reference to i2c_write' /home/liuw/armgnutoolchain132rel1x8664armnoneeabi/arm-gnu-toolchain-13.2.Rel1-x86_64-arm-none-eabi/bin/arm-none-eabi-ld.bfd: cmd/built-in.o: in function do_i2c_loop':
/home/liuw/Downloads/u-boot/cmd/i2c.c:1093:(.text.do_i2c_loop+0xac): undefined reference to `i2c_read'/home/liuw/armgnutoolchain132rel1x8664armnoneeabi/arm-gnu-toolchain-13.2.Rel1-x86_64-arm-none-eabi/bin/arm-none-eabi-ld.bfd: common/built-in.o: in function `jumptable_init':
/home/liuw/Downloads/u-boot/common/exports.c:32:(.text.jumptable_init+0x1cc): undefined reference to `i2c_write'/home/liuw/armgnutoolchain132rel1x8664armnoneeabi/arm-gnu-toolchain-13.2.Rel1-x86_64-arm-none-eabi/bin/arm-none-eabi-ld.bfd: /home/liuw/Downloads/u-boot/common/exports.c:32:(.text.jumptable_init+0x1d0): undefined reference to i2c_read' /home/liuw/armgnutoolchain132rel1x8664armnoneeabi/arm-gnu-toolchain-13.2.Rel1-x86_64-arm-none-eabi/bin/arm-none-eabi-ld.bfd: common/built-in.o: in function cread_line':
/home/liuw/Downloads/u-boot/common/cli_readline.c:266:(.text.cli_readline_into_buffer+0xd8): undefined reference to `get_tbclk' /home/liuw/armgnutoolchain132rel1x8664armnoneeabi/arm-gnu-toolchain-13.2.Rel1-x86_64-arm-none-eabi/bin/arm-none-eabi-ld.bfd: common/built-in.o:(.rodata.init_sequence_f+0x4c): undefined reference to print_cpuinfo' /home/liuw/armgnutoolchain132rel1x8664armnoneeabi/arm-gnu-toolchain-13.2.Rel1-x86_64-arm-none-eabi/bin/arm-none-eabi-ld.bfd: drivers/built-in.o: in function spi_flash_probe':
/home/liuw/Downloads/u-boot/drivers/mtd/spi/sf_probe.c:63:(.text.spi_flash_probe+0x4): undefined reference to spi_setup_slave' /home/liuw/armgnutoolchain132rel1x8664armnoneeabi/arm-gnu-toolchain-13.2.Rel1-x86_64-arm-none-eabi/bin/arm-none-eabi-ld.bfd: drivers/built-in.o: in function spi_flash_probe_slave':
/home/liuw/Downloads/u-boot/drivers/mtd/spi/sf_probe.c:38:(.text.spi_flash_probe+0x2c): undefined reference to spi_claim_bus' /home/liuw/armgnutoolchain132rel1x8664armnoneeabi/arm-gnu-toolchain-13.2.Rel1-x86_64-arm-none-eabi/bin/arm-none-eabi-ld.bfd: drivers/built-in.o: in function spi_flash_probe':
/home/liuw/Downloads/u-boot/drivers/mtd/spi/sf_probe.c:76:(.text.spi_flash_probe+0x3c): undefined reference to spi_free_slave' /home/liuw/armgnutoolchain132rel1x8664armnoneeabi/arm-gnu-toolchain-13.2.Rel1-x86_64-arm-none-eabi/bin/arm-none-eabi-ld.bfd: drivers/built-in.o: in function spi_flash_probe_slave':
/home/liuw/Downloads/u-boot/drivers/mtd/spi/sf_probe.c:52:(.text.spi_flash_probe+0x64): undefined reference to spi_release_bus' /home/liuw/armgnutoolchain132rel1x8664armnoneeabi/arm-gnu-toolchain-13.2.Rel1-x86_64-arm-none-eabi/bin/arm-none-eabi-ld.bfd: drivers/built-in.o: in function spi_flash_free':
/home/liuw/Downloads/u-boot/drivers/mtd/spi/sf_probe.c:89:(.text.spi_flash_free+0xc): undefined reference to spi_free_slave' /home/liuw/armgnutoolchain132rel1x8664armnoneeabi/arm-gnu-toolchain-13.2.Rel1-x86_64-arm-none-eabi/bin/arm-none-eabi-ld.bfd: drivers/serial/built-in.o: in function get_current':
/home/liuw/Downloads/u-boot/drivers/serial/serial.c:324:(.text.get_current+0x10): undefined reference to default_serial_console' /home/liuw/armgnutoolchain132rel1x8664armnoneeabi/arm-gnu-toolchain-13.2.Rel1-x86_64-arm-none-eabi/bin/arm-none-eabi-ld.bfd: drivers/serial/built-in.o: in function serial_initialize':
/home/liuw/Downloads/u-boot/drivers/serial/serial.c:185:(.text.serial_initialize+0x28): undefined reference to default_serial_console' /home/liuw/armgnutoolchain132rel1x8664armnoneeabi/arm-gnu-toolchain-13.2.Rel1-x86_64-arm-none-eabi/bin/arm-none-eabi-ld.bfd: drivers/spi/built-in.o: in function spi_mem_exec_op':
/home/liuw/Downloads/u-boot/drivers/spi/spi-mem-nodm.c:33:(.text.spi_mem_exec_op+0x58): undefined reference to `spi_claim_bus' /home/liuw/armgnutoolchain132rel1x8664armnoneeabi/arm-gnu-toolchain-13.2.Rel1-x86_64-arm-none-eabi/bin/arm-none-eabi-ld.bfd: /home/liuw/Downloads/u-boot/drivers/spi/spi-mem-nodm.c:56:(.text.spi_mem_exec_op+0x104): undefined reference to `spi_xfer' /home/liuw/armgnutoolchain132rel1x8664armnoneeabi/arm-gnu-toolchain-13.2.Rel1-x86_64-arm-none-eabi/bin/arm-none-eabi-ld.bfd: /home/liuw/Downloads/u-boot/drivers/spi/spi-mem-nodm.c:68:(.text.spi_mem_exec_op+0x120): undefined reference to `spi_release_bus' /home/liuw/armgnutoolchain132rel1x8664armnoneeabi/arm-gnu-toolchain-13.2.Rel1-x86_64-arm-none-eabi/bin/arm-none-eabi-ld.bfd: /home/liuw/Downloads/u-boot/drivers/spi/spi-mem-nodm.c:62:(.text.spi_mem_exec_op+0x154): undefined reference to spi_xfer' /home/liuw/armgnutoolchain132rel1x8664armnoneeabi/arm-gnu-toolchain-13.2.Rel1-x86_64-arm-none-eabi/bin/arm-none-eabi-ld.bfd: lib/built-in.o: in function tick_to_time':
/home/liuw/Downloads/u-boot/lib/time.c:123:(.text.tick_to_time+0x8): undefined reference to `get_tbclk'/home/liuw/armgnutoolchain132rel1x8664armnoneeabi/arm-gnu-toolchain-13.2.Rel1-x86_64-arm-none-eabi/bin/arm-none-eabi-ld.bfd: lib/built-in.o: in function `usec_to_tick':
/home/liuw/Downloads/u-boot/lib/time.c:168:(.text.usec_to_tick+0x8): undefined reference to `get_tbclk'
make: *** [Makefile:1753: u-boot] Error 1
Re: Could you please help me in resolving the " /reset.c:42:(.text.do_reset+0x20): undefined reference to `reset_cpu'?"
Hi Liu Wang,
Quoted 4 lines · Liu Wang
Hi Fabio,
Could you please help me in resolving the " /reset.c:42:(.text.do_reset+0x20): undefined reference to `reset_cpu'?" from: u-boot$make all:
Looking at the errors below, there are several errors besides the reset_cpu one.
As you are using an out-of-tree U-Boot, there is not much the U-Boot community can do to help you, sorry.
You need to get assistance from the U-Boot provider that you are using.
RE: Could you please help me in resolving the " /reset.c:42:(.text.do_reset+0x20): undefined reference to `reset_cpu'?"
Hi Fabio,
Thank you for your help.
Attached is the 'git status' and 'git log' in my porting u-boot to my cse_ptjob_cb3_r102 control board by following README in u-boot and being blocked with the hurdle of "undefined reference to `reset_cpu'" in hope you spot something familiar and shed a light in my building effort.
Sincerely,
Liu Wang
-----------------------------------------------------------------------------------------------------
liuw@liuw-SYS-E100-12T-H:~/Downloads/u-boot$ git log commit 050acee119b3757fee3bd128f55d720fdd9bb890 (HEAD, tag: v2020.10, list) Author: Tom Rini <[email protected]> Date: Mon Oct 5 11:15:32 2020 -0400
Prepare v2020.10
commit 0f3e2942c9e01b5dfc01f3dabe0e2f2ab8fd8b84
Author: Soeren Moch <[email protected]> Date: Thu Aug 27 21:52:46 2020 +0200
board: tbs2910: Use recommended distroboot addresses
According to doc/README.distro fdt_addr must not be set when DTB is not available from hardware. So remove this entry.
Use address 32MB above the start of DRAM for kernel_addr_r. This way we likely can avoid the self-relocation of the compressed kernel image before it decompresses to offset 0x8000 from start of DRAM.
Use address 128MB above the start of DRAM for fdt_addr_r, since this is the maximum location for the end of the kernel. So we avoid overwriting the DTB.
Use 512k above that for ramdisk_addr_r. This should be enough for the DTB, rest of DRAM can be used for initrd.
liuw@liuw-SYS-E100-12T-H:~/Downloads/u-boot$
-----------------------------------------------------------------------------
liuw@liuw-SYS-E100-12T-H:~/Downloads/u-boot$ git status HEAD detached at v2020.10 Changes not staged for commit: (use "git add <file>..." to update what will be committed) (use "git restore <file>..." to discard changes in working directory) modified: arch/arm/Kconfig modified: arch/arm/include/asm/arch-aspeed/platform.h modified: arch/arm/include/asm/global_data.h modified: cmd/bootm.c modified: cmd/i2c.c modified: cmd/load.c modified: cmd/source.c modified: common/image.c modified: fs/fs.c modified: include/command.h modified: include/ns16550.h
Untracked files:
(use "git add <file>..." to include in what will be committed)
board/supermicro/ configs/cse_ptjob_cb3_r102_defconfig include/configs/cast_common.h include/configs/cse_ptjob_cb3_r102.h listBin log2024011616makeAll.yml logmakeall2024012218 makelog
no changes added to commit (use "git add" and/or "git commit -a") liuw@liuw-SYS-E100-12T-H:~/Downloads/u-boot$
-----Original Message-----
From: Fabio Estevam <[email protected]>
Sent: Monday, January 22, 2024 6:44 PM
To: Liu Wang (HW) <[email protected]>
Cc: [email protected]
Subject: Re: Could you please help me in resolving the " /reset.c:42:(.text.do_reset+0x20): undefined reference to `reset_cpu'?"
[CAUTION: External Mail]
Hi Liu Wang,
Quoted 4 lines · Liu Wang
Hi Fabio,
Could you please help me in resolving the " /reset.c:42:(.text.do_reset+0x20): undefined reference to `reset_cpu'?" from: u-boot$make all:
Looking at the errors below, there are several errors besides the reset_cpu one.
As you are using an out-of-tree U-Boot, there is not much the U-Boot community can do to help you, sorry.
You need to get assistance from the U-Boot provider that you are using.
Re: Could you please help me in resolving the " /reset.c:42:(.text.do_reset+0x20): undefined reference to `reset_cpu'?"
Quoted 6 lines · Liu Wang
Hi Fabio,
Thank you for your help.
Attached is the 'git status' and 'git log' in my porting u-boot to my
cse_ptjob_cb3_r102control board by following README in u-boot and being blocked with the hurdle of "undefined reference to `reset_cpu'" in hope you spot something familiar and shed a light in my building effort.
I don't have any insight into the problem, unfortunately.
Also, v2020.10 is too old.
You should use mainline U-Boot and upstream your board (or hire someone to do it for you).
Re: Could you please help me in resolving the " /reset.c:42:(.text.do_reset+0x20): undefined reference to `reset_cpu'?"
Hi Fabio,
Thank you you review.
Sincerely,
Liu Wang
Quoted 18 lines · Fabio Estevam
[CAUTION: External Mail]
Quoted 7 lines · Liu Wang
Hi Fabio,
Thank you for your help.
Attached is the 'git status' and 'git log' in my porting u-boot to my
cse_ptjob_cb3_r102control board by following README in u-boot and being blocked with the hurdle of "undefined reference to `reset_cpu'" in hope you spot something familiar and shed a light in my building effort.I don't have any insight into the problem, unfortunately.
Also, v2020.10 is too old.
You should use mainline U-Boot and upstream your board (or hire someone to do it for you).