arm64: dts: meson: add support for ODROID-N2+
Subsystems (2)
cover arm64: dts: meson: add support for ODROID-N2+
This series splits the existing meson-g12b-odroid-n2.dts into a common dtsi and dts, and then adds new bindings and dts for the ODROID-N2+ which uses an Amlogic S922X rev.C chip that Hardkernel supports with overclock to 2.4GHz on the big cluster and 2.0GHz on the little cluster.
The series has a soft-dependency on proposed changes to N2 audio [0] from Jerome Brunet so will need a v2 rebase once they are applied (basic tests for this series on N2 and N2+ are with them applied).
[0] https://patchwork.kernel.org/project/linux-amlogic/list/?series=311099
Christian Hewitt (3):
arm64: dts: meson: convert ODROID-N2 to dtsi
dt-bindings: arm: amlogic: add support for the ODROID-N2+
arm64: dts: meson: add support for the ODROID-N2+
.../devicetree/bindings/arm/amlogic.yaml | 1 + arch/arm64/boot/dts/amlogic/Makefile | 1 + .../dts/amlogic/meson-g12b-odroid-n2-plus.dts | 53 ++ .../boot/dts/amlogic/meson-g12b-odroid-n2.dts | 493 +---------------- .../dts/amlogic/meson-g12b-odroid-n2.dtsi | 500 ++++++++++++++++++ 5 files changed, 556 insertions(+), 492 deletions(-) create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2-plus.dts create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi
Signature · 1 line
2.17.1
PATCH 1/3 arm64: dts: meson: convert ODROID-N2 to dtsi
Convert the current ODROID-N2 dts into a common dtsi in preparation for adding ODROID-N2+ support.
--- .../boot/dts/amlogic/meson-g12b-odroid-n2.dts | 493 +---------------- .../dts/amlogic/meson-g12b-odroid-n2.dtsi | 500 ++++++++++++++++++ 2 files changed, 501 insertions(+), 492 deletions(-) create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi
arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts +1 -492
@@ -6,500 +6,9 @@ /dts-v1/; -#include "meson-g12b-s922x.dtsi" -#include <dt-bindings/input/input.h> -#include <dt-bindings/gpio/meson-g12a-gpio.h> -#include <dt-bindings/sound/meson-g12a-tohdmitx.h> +#include "meson-g12b-odroid-n2.dtsi" / { compatible = "hardkernel,odroid-n2", "amlogic,s922x", "amlogic,g12b"; model = "Hardkernel ODROID-N2"; - - aliases { - serial0 = &uart_AO; - ethernet0 = ðmac; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - memory@0 { - device_type = "memory"; - reg = <0x0 0x0 0x0 0x40000000>; - }; - - emmc_pwrseq: emmc-pwrseq { - compatible = "mmc-pwrseq-emmc"; - reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>; - }; - - leds { - compatible = "gpio-leds"; - - blue { - label = "n2:blue"; - gpios = <&gpio_ao GPIOAO_11 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "heartbeat"; - }; - }; - - tflash_vdd: regulator-tflash_vdd { - compatible = "regulator-fixed"; - - regulator-name = "TFLASH_VDD"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - - gpio = <&gpio_ao GPIOAO_8 GPIO_ACTIVE_HIGH>; - enable-active-high; - regulator-always-on; - }; - - tf_io: gpio-regulator-tf_io { - compatible = "regulator-gpio"; - - regulator-name = "TF_IO"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3300000>; - - gpios = <&gpio_ao GPIOAO_9 GPIO_ACTIVE_HIGH>; - gpios-states = <0>; - - states = <3300000 0>, - <1800000 1>; - }; - - flash_1v8: regulator-flash_1v8 { - compatible = "regulator-fixed"; - regulator-name = "FLASH_1V8"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - vin-supply = <&vcc_3v3>; - regulator-always-on; - }; - - main_12v: regulator-main_12v { - compatible = "regulator-fixed"; - regulator-name = "12V"; - regulator-min-microvolt = <12000000>; - regulator-max-microvolt = <12000000>; - regulator-always-on; - }; - - vcc_5v: regulator-vcc_5v { - compatible = "regulator-fixed"; - regulator-name = "5V"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - regulator-always-on; - vin-supply = <&main_12v>; - }; - - vcc_1v8: regulator-vcc_1v8 { - compatible = "regulator-fixed"; - regulator-name = "VCC_1V8"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - vin-supply = <&vcc_3v3>; - regulator-always-on; - }; - - vcc_3v3: regulator-vcc_3v3 { - compatible = "regulator-fixed"; - regulator-name = "VCC_3V3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - vin-supply = <&vddao_3v3>; - regulator-always-on; - /* FIXME: actually controlled by VDDCPU_B_EN */ - }; - - vddcpu_a: regulator-vddcpu-a { - /* - * MP8756GD Regulator. - */ - compatible = "pwm-regulator"; - - regulator-name = "VDDCPU_A"; - regulator-min-microvolt = <721000>; - regulator-max-microvolt = <1022000>; - - vin-supply = <&main_12v>; - - pwms = <&pwm_ab 0 1250 0>; - pwm-dutycycle-range = <100 0>; - - regulator-boot-on; - regulator-always-on; - }; - - vddcpu_b: regulator-vddcpu-b { - /* - * Silergy SY8120B1ABC Regulator. - */ - compatible = "pwm-regulator"; - - regulator-name = "VDDCPU_B"; - regulator-min-microvolt = <721000>; - regulator-max-microvolt = <1022000>; - - vin-supply = <&main_12v>; - - pwms = <&pwm_AO_cd 1 1250 0>; - pwm-dutycycle-range = <100 0>; - - regulator-boot-on; - regulator-always-on; - }; - - hub_5v: regulator-hub_5v { - compatible = "regulator-fixed"; - regulator-name = "HUB_5V"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - vin-supply = <&vcc_5v>; - - /* Connected to the Hub CHIPENABLE, LOW sets low power state */ - gpio = <&gpio GPIOH_5 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; - - usb_pwr_en: regulator-usb_pwr_en { - compatible = "regulator-fixed"; - regulator-name = "USB_PWR_EN"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - vin-supply = <&vcc_5v>; - - /* Connected to the microUSB port power enable */ - gpio = <&gpio GPIOH_6 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; - - vddao_1v8: regulator-vddao_1v8 { - compatible = "regulator-fixed"; - regulator-name = "VDDAO_1V8"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - vin-supply = <&vddao_3v3>; - regulator-always-on; - }; - - vddao_3v3: regulator-vddao_3v3 { - compatible = "regulator-fixed"; - regulator-name = "VDDAO_3V3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - vin-supply = <&main_12v>; - regulator-always-on; - }; - - hdmi-connector { - compatible = "hdmi-connector"; - type = "a"; - - port { - hdmi_connector_in: endpoint { - remote-endpoint = <&hdmi_tx_tmds_out>; - }; - }; - }; - - sound { - compatible = "amlogic,axg-sound-card"; - model = "G12B-ODROID-N2"; - audio-aux-devs = <&tdmout_b>; - audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1", - "TDMOUT_B IN 1", "FRDDR_B OUT 1", - "TDMOUT_B IN 2", "FRDDR_C OUT 1", - "TDM_B Playback", "TDMOUT_B OUT"; - - assigned-clocks = <&clkc CLKID_MPLL2>, - <&clkc CLKID_MPLL0>, - <&clkc CLKID_MPLL1>; - assigned-clock-parents = <0>, <0>, <0>; - assigned-clock-rates = <294912000>, - <270950400>, - <393216000>; - status = "okay"; - - dai-link-0 { - sound-dai = <&frddr_a>; - }; - - dai-link-1 { - sound-dai = <&frddr_b>; - }; - - dai-link-2 { - sound-dai = <&frddr_c>; - }; - - /* 8ch hdmi interface */ - dai-link-3 { - sound-dai = <&tdmif_b>; - dai-format = "i2s"; - dai-tdm-slot-tx-mask-0 = <1 1>; - dai-tdm-slot-tx-mask-1 = <1 1>; - dai-tdm-slot-tx-mask-2 = <1 1>; - dai-tdm-slot-tx-mask-3 = <1 1>; - mclk-fs = <256>; - - codec { - sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>; - }; - }; - - /* hdmi glue */ - dai-link-4 { - sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>; - - codec { - sound-dai = <&hdmi_tx>; - }; - }; - }; -}; - -&arb { - status = "okay"; -}; - -&cec_AO { - pinctrl-0 = <&cec_ao_a_h_pins>; - pinctrl-names = "default"; - status = "disabled"; - hdmi-phandle = <&hdmi_tx>; -}; - -&cecb_AO { - pinctrl-0 = <&cec_ao_b_h_pins>; - pinctrl-names = "default"; - status = "okay"; - hdmi-phandle = <&hdmi_tx>; -}; - -&clkc_audio { - status = "okay"; -}; - -&cpu0 { - cpu-supply = <&vddcpu_b>; - operating-points-v2 = <&cpu_opp_table_0>; - clocks = <&clkc CLKID_CPU_CLK>; - clock-latency = <50000>; -}; - -&cpu1 { - cpu-supply = <&vddcpu_b>; - operating-points-v2 = <&cpu_opp_table_0>; - clocks = <&clkc CLKID_CPU_CLK>; - clock-latency = <50000>; -}; - -&cpu100 { - cpu-supply = <&vddcpu_a>; - operating-points-v2 = <&cpub_opp_table_1>; - clocks = <&clkc CLKID_CPUB_CLK>; - clock-latency = <50000>; -}; - -&cpu101 { - cpu-supply = <&vddcpu_a>; - operating-points-v2 = <&cpub_opp_table_1>; - clocks = <&clkc CLKID_CPUB_CLK>; - clock-latency = <50000>; -}; - -&cpu102 { - cpu-supply = <&vddcpu_a>; - operating-points-v2 = <&cpub_opp_table_1>; - clocks = <&clkc CLKID_CPUB_CLK>; - clock-latency = <50000>; -}; - -&cpu103 { - cpu-supply = <&vddcpu_a>; - operating-points-v2 = <&cpub_opp_table_1>; - clocks = <&clkc CLKID_CPUB_CLK>; - clock-latency = <50000>; -}; - -&ext_mdio { - external_phy: ethernet-phy@0 { - /* Realtek RTL8211F (0x001cc916) */ - reg = <0>; - max-speed = <1000>; - - reset-assert-us = <10000>; - reset-deassert-us = <30000>; - reset-gpios = <&gpio GPIOZ_15 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>; - - interrupt-parent = <&gpio_intc>; - /* MAC_INTR on GPIOZ_14 */ - interrupts = <26 IRQ_TYPE_LEVEL_LOW>; - }; -}; - -ðmac { - pinctrl-0 = <ð_pins>, <ð_rgmii_pins>; - pinctrl-names = "default"; - status = "okay"; - phy-mode = "rgmii"; - phy-handle = <&external_phy>; - amlogic,tx-delay-ns = <2>; -}; - -&frddr_a { - status = "okay"; -}; - -&frddr_b { - status = "okay"; -}; - -&frddr_c { - status = "okay"; -}; - -&gpio { - /* - * WARNING: The USB Hub on the Odroid-N2 needs a reset signal - * to be turned high in order to be detected by the USB Controller - * This signal should be handled by a USB specific power sequence - * in order to reset the Hub when USB bus is powered down. - */ - usb-hub { - gpio-hog; - gpios = <GPIOH_4 GPIO_ACTIVE_HIGH>; - output-high; - line-name = "usb-hub-reset"; - }; -}; - -&hdmi_tx { - status = "okay"; - pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>; - pinctrl-names = "default"; - hdmi-supply = <&vcc_5v>; -}; - -&hdmi_tx_tmds_port { - hdmi_tx_tmds_out: endpoint { - remote-endpoint = <&hdmi_connector_in>; - }; -}; - -&ir { - status = "okay"; - pinctrl-0 = <&remote_input_ao_pins>; - pinctrl-names = "default"; - linux,rc-map-name = "rc-odroid"; -}; - -&pwm_ab { - pinctrl-0 = <&pwm_a_e_pins>; - pinctrl-names = "default"; - clocks = <&xtal>; - clock-names = "clkin0"; - status = "okay"; -}; - -&pwm_AO_cd { - pinctrl-0 = <&pwm_ao_d_e_pins>; - pinctrl-names = "default"; - clocks = <&xtal>; - clock-names = "clkin1"; - status = "okay"; -}; - -/* SD card */ -&sd_emmc_b { - status = "okay"; - pinctrl-0 = <&sdcard_c_pins>; - pinctrl-1 = <&sdcard_clk_gate_c_pins>; - pinctrl-names = "default", "clk-gate"; - - bus-width = <4>; - cap-sd-highspeed; - max-frequency = <50000000>; - disable-wp; - - cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>; - vmmc-supply = <&tflash_vdd>; - vqmmc-supply = <&tf_io>; - -}; - -/* eMMC */ -&sd_emmc_c { - status = "okay"; - pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>; - pinctrl-1 = <&emmc_clk_gate_pins>; - pinctrl-names = "default", "clk-gate"; - - bus-width = <8>; - cap-mmc-highspeed; - mmc-ddr-1_8v; - mmc-hs200-1_8v; - max-frequency = <200000000>; - disable-wp; - - mmc-pwrseq = <&emmc_pwrseq>; - vmmc-supply = <&vcc_3v3>; - vqmmc-supply = <&flash_1v8>; -}; - -/* - * EMMC_D4, EMMC_D5, EMMC_D6 and EMMC_D7 pins are shared between SPI NOR pins - * and eMMC Data 4 to 7 pins. - * Replace emmc_data_8b_pins to emmc_data_4b_pins from sd_emmc_c pinctrl-0, - * and change bus-width to 4 then spifc can be enabled. - * The SW1 slide should also be set to the correct position. - */ -&spifc { - status = "disabled"; - pinctrl-0 = <&nor_pins>; - pinctrl-names = "default"; - - mx25u64: spi-flash@0 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "mxicy,mx25u6435f", "jedec,spi-nor"; - reg = <0>; - spi-max-frequency = <104000000>; - }; -}; - -&tdmif_b { - status = "okay"; -}; - -&tdmout_b { - status = "okay"; -}; - -&tohdmitx { - status = "okay"; -}; - -&uart_AO { - status = "okay"; - pinctrl-0 = <&uart_ao_a_pins>; - pinctrl-names = "default"; -}; - -&usb { - status = "okay"; - vbus-supply = <&usb_pwr_en>; -}; - -&usb2_phy0 { - phy-supply = <&vcc_5v>; -}; - -&usb2_phy1 { - /* Enable the hub which is connected to this port */ - phy-supply = <&hub_5v>; };
arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi new file +500 -0
500 lines not on this page · raw message
Signature · 1 line
2.17.1
Re: [PATCH 1/3] arm64: dts: meson: convert ODROID-N2 to dtsi
Quoted 1,013 lines · Christian Hewitt
Convert the current ODROID-N2 dts into a common dtsi in preparation for adding ODROID-N2+ support.
Signed-off-by Christian Hewitt <[email protected]>--- .../boot/dts/amlogic/meson-g12b-odroid-n2.dts | 493 +---------------- .../dts/amlogic/meson-g12b-odroid-n2.dtsi | 500 ++++++++++++++++++ 2 files changed, 501 insertions(+), 492 deletions(-) create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsiarch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dts +1
-492@@ -6,500 +6,9 @@ /dts-v1/; -#include "meson-g12b-s922x.dtsi" -#include <dt-bindings/input/input.h> -#include <dt-bindings/gpio/meson-g12a-gpio.h> -#include <dt-bindings/sound/meson-g12a-tohdmitx.h> +#include "meson-g12b-odroid-n2.dtsi" / { compatible = "hardkernel,odroid-n2", "amlogic,s922x", "amlogic,g12b"; model = "Hardkernel ODROID-N2"; - - aliases { - serial0 = &uart_AO; - ethernet0 = ðmac; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - memory@0 { - device_type = "memory"; - reg = <0x0 0x0 0x0 0x40000000>; - }; - - emmc_pwrseq: emmc-pwrseq { - compatible = "mmc-pwrseq-emmc"; - reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>; - }; - - leds { - compatible = "gpio-leds"; - - blue { - label = "n2:blue"; - gpios = <&gpio_ao GPIOAO_11 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "heartbeat"; - }; - }; - - tflash_vdd: regulator-tflash_vdd { - compatible = "regulator-fixed"; - - regulator-name = "TFLASH_VDD"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - - gpio = <&gpio_ao GPIOAO_8 GPIO_ACTIVE_HIGH>; - enable-active-high; - regulator-always-on; - }; - - tf_io: gpio-regulator-tf_io { - compatible = "regulator-gpio"; - - regulator-name = "TF_IO"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3300000>; - - gpios = <&gpio_ao GPIOAO_9 GPIO_ACTIVE_HIGH>; - gpios-states = <0>; - - states = <3300000 0>, - <1800000 1>; - }; - - flash_1v8: regulator-flash_1v8 { - compatible = "regulator-fixed"; - regulator-name = "FLASH_1V8"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - vin-supply = <&vcc_3v3>; - regulator-always-on; - }; - - main_12v: regulator-main_12v { - compatible = "regulator-fixed"; - regulator-name = "12V"; - regulator-min-microvolt = <12000000>; - regulator-max-microvolt = <12000000>; - regulator-always-on; - }; - - vcc_5v: regulator-vcc_5v { - compatible = "regulator-fixed"; - regulator-name = "5V"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - regulator-always-on; - vin-supply = <&main_12v>; - }; - - vcc_1v8: regulator-vcc_1v8 { - compatible = "regulator-fixed"; - regulator-name = "VCC_1V8"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - vin-supply = <&vcc_3v3>; - regulator-always-on; - }; - - vcc_3v3: regulator-vcc_3v3 { - compatible = "regulator-fixed"; - regulator-name = "VCC_3V3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - vin-supply = <&vddao_3v3>; - regulator-always-on; - /* FIXME: actually controlled by VDDCPU_B_EN */ - }; - - vddcpu_a: regulator-vddcpu-a { - /* - * MP8756GD Regulator. - */ - compatible = "pwm-regulator"; - - regulator-name = "VDDCPU_A"; - regulator-min-microvolt = <721000>; - regulator-max-microvolt = <1022000>; - - vin-supply = <&main_12v>; - - pwms = <&pwm_ab 0 1250 0>; - pwm-dutycycle-range = <100 0>; - - regulator-boot-on; - regulator-always-on; - }; - - vddcpu_b: regulator-vddcpu-b { - /* - * Silergy SY8120B1ABC Regulator. - */ - compatible = "pwm-regulator"; - - regulator-name = "VDDCPU_B"; - regulator-min-microvolt = <721000>; - regulator-max-microvolt = <1022000>; - - vin-supply = <&main_12v>; - - pwms = <&pwm_AO_cd 1 1250 0>; - pwm-dutycycle-range = <100 0>; - - regulator-boot-on; - regulator-always-on; - }; - - hub_5v: regulator-hub_5v { - compatible = "regulator-fixed"; - regulator-name = "HUB_5V"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - vin-supply = <&vcc_5v>; - - /* Connected to the Hub CHIPENABLE, LOW sets low power state */ - gpio = <&gpio GPIOH_5 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; - - usb_pwr_en: regulator-usb_pwr_en { - compatible = "regulator-fixed"; - regulator-name = "USB_PWR_EN"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - vin-supply = <&vcc_5v>; - - /* Connected to the microUSB port power enable */ - gpio = <&gpio GPIOH_6 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; - - vddao_1v8: regulator-vddao_1v8 { - compatible = "regulator-fixed"; - regulator-name = "VDDAO_1V8"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - vin-supply = <&vddao_3v3>; - regulator-always-on; - }; - - vddao_3v3: regulator-vddao_3v3 { - compatible = "regulator-fixed"; - regulator-name = "VDDAO_3V3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - vin-supply = <&main_12v>; - regulator-always-on; - }; - - hdmi-connector { - compatible = "hdmi-connector"; - type = "a"; - - port { - hdmi_connector_in: endpoint { - remote-endpoint = <&hdmi_tx_tmds_out>; - }; - }; - }; - - sound { - compatible = "amlogic,axg-sound-card"; - model = "G12B-ODROID-N2"; - audio-aux-devs = <&tdmout_b>; - audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1", - "TDMOUT_B IN 1", "FRDDR_B OUT 1", - "TDMOUT_B IN 2", "FRDDR_C OUT 1", - "TDM_B Playback", "TDMOUT_B OUT"; - - assigned-clocks = <&clkc CLKID_MPLL2>, - <&clkc CLKID_MPLL0>, - <&clkc CLKID_MPLL1>; - assigned-clock-parents = <0>, <0>, <0>; - assigned-clock-rates = <294912000>, - <270950400>, - <393216000>; - status = "okay"; - - dai-link-0 { - sound-dai = <&frddr_a>; - }; - - dai-link-1 { - sound-dai = <&frddr_b>; - }; - - dai-link-2 { - sound-dai = <&frddr_c>; - }; - - /* 8ch hdmi interface */ - dai-link-3 { - sound-dai = <&tdmif_b>; - dai-format = "i2s"; - dai-tdm-slot-tx-mask-0 = <1 1>; - dai-tdm-slot-tx-mask-1 = <1 1>; - dai-tdm-slot-tx-mask-2 = <1 1>; - dai-tdm-slot-tx-mask-3 = <1 1>; - mclk-fs = <256>; - - codec { - sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>; - }; - }; - - /* hdmi glue */ - dai-link-4 { - sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>; - - codec { - sound-dai = <&hdmi_tx>; - }; - }; - }; -}; - -&arb { - status = "okay"; -}; - -&cec_AO { - pinctrl-0 = <&cec_ao_a_h_pins>; - pinctrl-names = "default"; - status = "disabled"; - hdmi-phandle = <&hdmi_tx>; -}; - -&cecb_AO { - pinctrl-0 = <&cec_ao_b_h_pins>; - pinctrl-names = "default"; - status = "okay"; - hdmi-phandle = <&hdmi_tx>; -}; - -&clkc_audio { - status = "okay"; -}; - -&cpu0 { - cpu-supply = <&vddcpu_b>; - operating-points-v2 = <&cpu_opp_table_0>; - clocks = <&clkc CLKID_CPU_CLK>; - clock-latency = <50000>; -}; - -&cpu1 { - cpu-supply = <&vddcpu_b>; - operating-points-v2 = <&cpu_opp_table_0>; - clocks = <&clkc CLKID_CPU_CLK>; - clock-latency = <50000>; -}; - -&cpu100 { - cpu-supply = <&vddcpu_a>; - operating-points-v2 = <&cpub_opp_table_1>; - clocks = <&clkc CLKID_CPUB_CLK>; - clock-latency = <50000>; -}; - -&cpu101 { - cpu-supply = <&vddcpu_a>; - operating-points-v2 = <&cpub_opp_table_1>; - clocks = <&clkc CLKID_CPUB_CLK>; - clock-latency = <50000>; -}; - -&cpu102 { - cpu-supply = <&vddcpu_a>; - operating-points-v2 = <&cpub_opp_table_1>; - clocks = <&clkc CLKID_CPUB_CLK>; - clock-latency = <50000>; -}; - -&cpu103 { - cpu-supply = <&vddcpu_a>; - operating-points-v2 = <&cpub_opp_table_1>; - clocks = <&clkc CLKID_CPUB_CLK>; - clock-latency = <50000>; -}; - -&ext_mdio { - external_phy: ethernet-phy@0 { - /* Realtek RTL8211F (0x001cc916) */ - reg = <0>; - max-speed = <1000>; - - reset-assert-us = <10000>; - reset-deassert-us = <30000>; - reset-gpios = <&gpio GPIOZ_15 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>; - - interrupt-parent = <&gpio_intc>; - /* MAC_INTR on GPIOZ_14 */ - interrupts = <26 IRQ_TYPE_LEVEL_LOW>; - }; -}; - -ðmac { - pinctrl-0 = <ð_pins>, <ð_rgmii_pins>; - pinctrl-names = "default"; - status = "okay"; - phy-mode = "rgmii"; - phy-handle = <&external_phy>; - amlogic,tx-delay-ns = <2>; -}; - -&frddr_a { - status = "okay"; -}; - -&frddr_b { - status = "okay"; -}; - -&frddr_c { - status = "okay"; -}; - -&gpio { - /* - * WARNING: The USB Hub on the Odroid-N2 needs a reset signal - * to be turned high in order to be detected by the USB Controller - * This signal should be handled by a USB specific power sequence - * in order to reset the Hub when USB bus is powered down. - */ - usb-hub { - gpio-hog; - gpios = <GPIOH_4 GPIO_ACTIVE_HIGH>; - output-high; - line-name = "usb-hub-reset"; - }; -}; - -&hdmi_tx { - status = "okay"; - pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>; - pinctrl-names = "default"; - hdmi-supply = <&vcc_5v>; -}; - -&hdmi_tx_tmds_port { - hdmi_tx_tmds_out: endpoint { - remote-endpoint = <&hdmi_connector_in>; - }; -}; - -&ir { - status = "okay"; - pinctrl-0 = <&remote_input_ao_pins>; - pinctrl-names = "default"; - linux,rc-map-name = "rc-odroid"; -}; - -&pwm_ab { - pinctrl-0 = <&pwm_a_e_pins>; - pinctrl-names = "default"; - clocks = <&xtal>; - clock-names = "clkin0"; - status = "okay"; -}; - -&pwm_AO_cd { - pinctrl-0 = <&pwm_ao_d_e_pins>; - pinctrl-names = "default"; - clocks = <&xtal>; - clock-names = "clkin1"; - status = "okay"; -}; - -/* SD card */ -&sd_emmc_b { - status = "okay"; - pinctrl-0 = <&sdcard_c_pins>; - pinctrl-1 = <&sdcard_clk_gate_c_pins>; - pinctrl-names = "default", "clk-gate"; - - bus-width = <4>; - cap-sd-highspeed; - max-frequency = <50000000>; - disable-wp; - - cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>; - vmmc-supply = <&tflash_vdd>; - vqmmc-supply = <&tf_io>; - -}; - -/* eMMC */ -&sd_emmc_c { - status = "okay"; - pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>; - pinctrl-1 = <&emmc_clk_gate_pins>; - pinctrl-names = "default", "clk-gate"; - - bus-width = <8>; - cap-mmc-highspeed; - mmc-ddr-1_8v; - mmc-hs200-1_8v; - max-frequency = <200000000>; - disable-wp; - - mmc-pwrseq = <&emmc_pwrseq>; - vmmc-supply = <&vcc_3v3>; - vqmmc-supply = <&flash_1v8>; -}; - -/* - * EMMC_D4, EMMC_D5, EMMC_D6 and EMMC_D7 pins are shared between SPI NOR pins - * and eMMC Data 4 to 7 pins. - * Replace emmc_data_8b_pins to emmc_data_4b_pins from sd_emmc_c pinctrl-0, - * and change bus-width to 4 then spifc can be enabled. - * The SW1 slide should also be set to the correct position. - */ -&spifc { - status = "disabled"; - pinctrl-0 = <&nor_pins>; - pinctrl-names = "default"; - - mx25u64: spi-flash@0 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "mxicy,mx25u6435f", "jedec,spi-nor"; - reg = <0>; - spi-max-frequency = <104000000>; - }; -}; - -&tdmif_b { - status = "okay"; -}; - -&tdmout_b { - status = "okay"; -}; - -&tohdmitx { - status = "okay"; -}; - -&uart_AO { - status = "okay"; - pinctrl-0 = <&uart_ao_a_pins>; - pinctrl-names = "default"; -}; - -&usb { - status = "okay"; - vbus-supply = <&usb_pwr_en>; -}; - -&usb2_phy0 { - phy-supply = <&vcc_5v>; -}; - -&usb2_phy1 { - /* Enable the hub which is connected to this port */ - phy-supply = <&hub_5v>; };arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi new file +490
-0@@ -0,0 +1,500 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2019 BayLibre, SAS + * Author: Neil Armstrong <[email protected]> + */ + +#include "meson-g12b-s922x.dtsi" +#include <dt-bindings/input/input.h> +#include <dt-bindings/gpio/meson-g12a-gpio.h> +#include <dt-bindings/sound/meson-g12a-tohdmitx.h> + +/ { + aliases { + serial0 = &uart_AO; + ethernet0 = ðmac; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x0 0x0 0x40000000>; + }; + + emmc_pwrseq: emmc-pwrseq { + compatible = "mmc-pwrseq-emmc"; + reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>; + }; + + leds { + compatible = "gpio-leds"; + + blue { + label = "n2:blue"; + gpios = <&gpio_ao GPIOAO_11 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + }; + + tflash_vdd: regulator-tflash_vdd { + compatible = "regulator-fixed"; + + regulator-name = "TFLASH_VDD"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&gpio_ao GPIOAO_8 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-always-on; + }; + + tf_io: gpio-regulator-tf_io { + compatible = "regulator-gpio"; + + regulator-name = "TF_IO"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + + gpios = <&gpio_ao GPIOAO_9 GPIO_ACTIVE_HIGH>; + gpios-states = <0>; + + states = <3300000 0>, + <1800000 1>; + }; + + flash_1v8: regulator-flash_1v8 { + compatible = "regulator-fixed"; + regulator-name = "FLASH_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vcc_3v3>; + regulator-always-on; + }; + + main_12v: regulator-main_12v { + compatible = "regulator-fixed"; + regulator-name = "12V"; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; + regulator-always-on; + }; + + vcc_5v: regulator-vcc_5v { + compatible = "regulator-fixed"; + regulator-name = "5V"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + vin-supply = <&main_12v>; + }; + + vcc_1v8: regulator-vcc_1v8 { + compatible = "regulator-fixed"; + regulator-name = "VCC_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vcc_3v3>; + regulator-always-on; + }; + + vcc_3v3: regulator-vcc_3v3 { + compatible = "regulator-fixed"; + regulator-name = "VCC_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vddao_3v3>; + regulator-always-on; + /* FIXME: actually controlled by VDDCPU_B_EN */ + }; + + vddcpu_a: regulator-vddcpu-a { + /* + * MP8756GD Regulator. + */ + compatible = "pwm-regulator"; + + regulator-name = "VDDCPU_A"; + regulator-min-microvolt = <721000>; + regulator-max-microvolt = <1022000>; + + vin-supply = <&main_12v>; + + pwms = <&pwm_ab 0 1250 0>; + pwm-dutycycle-range = <100 0>; + + regulator-boot-on; + regulator-always-on; + }; + + vddcpu_b: regulator-vddcpu-b { + /* + * Silergy SY8120B1ABC Regulator. + */ + compatible = "pwm-regulator"; + + regulator-name = "VDDCPU_B"; + regulator-min-microvolt = <721000>; + regulator-max-microvolt = <1022000>; + + vin-supply = <&main_12v>; + + pwms = <&pwm_AO_cd 1 1250 0>; + pwm-dutycycle-range = <100 0>; + + regulator-boot-on; + regulator-always-on; + }; + + hub_5v: regulator-hub_5v { + compatible = "regulator-fixed"; + regulator-name = "HUB_5V"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <&vcc_5v>; + + /* Connected to the Hub CHIPENABLE, LOW sets low power state */ + gpio = <&gpio GPIOH_5 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + usb_pwr_en: regulator-usb_pwr_en { + compatible = "regulator-fixed"; + regulator-name = "USB_PWR_EN"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <&vcc_5v>; + + /* Connected to the microUSB port power enable */ + gpio = <&gpio GPIOH_6 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + vddao_1v8: regulator-vddao_1v8 { + compatible = "regulator-fixed"; + regulator-name = "VDDAO_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vddao_3v3>; + regulator-always-on; + }; + + vddao_3v3: regulator-vddao_3v3 { + compatible = "regulator-fixed"; + regulator-name = "VDDAO_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&main_12v>; + regulator-always-on; + }; + + hdmi-connector { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_connector_in: endpoint { + remote-endpoint = <&hdmi_tx_tmds_out>; + }; + }; + }; + + sound { + compatible = "amlogic,axg-sound-card"; + model = "G12B-ODROID-N2"; + audio-aux-devs = <&tdmout_b>; + audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1", + "TDMOUT_B IN 1", "FRDDR_B OUT 1", + "TDMOUT_B IN 2", "FRDDR_C OUT 1", + "TDM_B Playback", "TDMOUT_B OUT"; + + assigned-clocks = <&clkc CLKID_MPLL2>, + <&clkc CLKID_MPLL0>, + <&clkc CLKID_MPLL1>; + assigned-clock-parents = <0>, <0>, <0>; + assigned-clock-rates = <294912000>, + <270950400>, + <393216000>; + status = "okay"; + + dai-link-0 { + sound-dai = <&frddr_a>; + }; + + dai-link-1 { + sound-dai = <&frddr_b>; + }; + + dai-link-2 { + sound-dai = <&frddr_c>; + }; + + /* 8ch hdmi interface */ + dai-link-3 { + sound-dai = <&tdmif_b>; + dai-format = "i2s"; + dai-tdm-slot-tx-mask-0 = <1 1>; + dai-tdm-slot-tx-mask-1 = <1 1>; + dai-tdm-slot-tx-mask-2 = <1 1>; + dai-tdm-slot-tx-mask-3 = <1 1>; + mclk-fs = <256>; + + codec { + sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>; + }; + }; + + /* hdmi glue */ + dai-link-4 { + sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>; + + codec { + sound-dai = <&hdmi_tx>; + }; + }; + }; +}; + +&arb { + status = "okay"; +}; + +&cec_AO { + pinctrl-0 = <&cec_ao_a_h_pins>; + pinctrl-names = "default"; + status = "disabled"; + hdmi-phandle = <&hdmi_tx>; +}; + +&cecb_AO { + pinctrl-0 = <&cec_ao_b_h_pins>; + pinctrl-names = "default"; + status = "okay"; + hdmi-phandle = <&hdmi_tx>; +}; + +&clkc_audio { + status = "okay"; +}; + +&cpu0 { + cpu-supply = <&vddcpu_b>; + operating-points-v2 = <&cpu_opp_table_0>; + clocks = <&clkc CLKID_CPU_CLK>; + clock-latency = <50000>; +}; + +&cpu1 { + cpu-supply = <&vddcpu_b>; + operating-points-v2 = <&cpu_opp_table_0>; + clocks = <&clkc CLKID_CPU_CLK>; + clock-latency = <50000>; +}; + +&cpu100 { + cpu-supply = <&vddcpu_a>; + operating-points-v2 = <&cpub_opp_table_1>; + clocks = <&clkc CLKID_CPUB_CLK>; + clock-latency = <50000>; +}; + +&cpu101 { + cpu-supply = <&vddcpu_a>; + operating-points-v2 = <&cpub_opp_table_1>; + clocks = <&clkc CLKID_CPUB_CLK>; + clock-latency = <50000>; +}; + +&cpu102 { + cpu-supply = <&vddcpu_a>; + operating-points-v2 = <&cpub_opp_table_1>; + clocks = <&clkc CLKID_CPUB_CLK>; + clock-latency = <50000>; +}; + +&cpu103 { + cpu-supply = <&vddcpu_a>; + operating-points-v2 = <&cpub_opp_table_1>; + clocks = <&clkc CLKID_CPUB_CLK>; + clock-latency = <50000>; +}; + +&ext_mdio { + external_phy: ethernet-phy@0 { + /* Realtek RTL8211F (0x001cc916) */ + reg = <0>; + max-speed = <1000>; + + reset-assert-us = <10000>; + reset-deassert-us = <30000>; + reset-gpios = <&gpio GPIOZ_15 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>; + + interrupt-parent = <&gpio_intc>; + /* MAC_INTR on GPIOZ_14 */ + interrupts = <26 IRQ_TYPE_LEVEL_LOW>; + }; +}; + +ðmac { + pinctrl-0 = <ð_pins>, <ð_rgmii_pins>; + pinctrl-names = "default"; + status = "okay"; + phy-mode = "rgmii"; + phy-handle = <&external_phy>; + amlogic,tx-delay-ns = <2>; +}; + +&frddr_a { + status = "okay"; +}; + +&frddr_b { + status = "okay"; +}; + +&frddr_c { + status = "okay"; +}; + +&gpio { + /* + * WARNING: The USB Hub on the Odroid-N2 needs a reset signal + * to be turned high in order to be detected by the USB Controller + * This signal should be handled by a USB specific power sequence + * in order to reset the Hub when USB bus is powered down. + */ + usb-hub { + gpio-hog; + gpios = <GPIOH_4 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "usb-hub-reset"; + }; +}; + +&hdmi_tx { + status = "okay"; + pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>; + pinctrl-names = "default"; + hdmi-supply = <&vcc_5v>; +}; + +&hdmi_tx_tmds_port { + hdmi_tx_tmds_out: endpoint { + remote-endpoint = <&hdmi_connector_in>; + }; +}; + +&ir { + status = "okay"; + pinctrl-0 = <&remote_input_ao_pins>; + pinctrl-names = "default"; + linux,rc-map-name = "rc-odroid"; +}; + +&pwm_ab { + pinctrl-0 = <&pwm_a_e_pins>; + pinctrl-names = "default"; + clocks = <&xtal>; + clock-names = "clkin0"; + status = "okay"; +}; + +&pwm_AO_cd { + pinctrl-0 = <&pwm_ao_d_e_pins>; + pinctrl-names = "default"; + clocks = <&xtal>; + clock-names = "clkin1"; + status = "okay"; +}; + +/* SD card */ +&sd_emmc_b { + status = "okay"; + pinctrl-0 = <&sdcard_c_pins>; + pinctrl-1 = <&sdcard_clk_gate_c_pins>; + pinctrl-names = "default", "clk-gate"; + + bus-width = <4>; + cap-sd-highspeed; + max-frequency = <50000000>; + disable-wp; + + cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>; + vmmc-supply = <&tflash_vdd>; + vqmmc-supply = <&tf_io>; + +}; + +/* eMMC */ +&sd_emmc_c { + status = "okay"; + pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>; + pinctrl-1 = <&emmc_clk_gate_pins>; + pinctrl-names = "default", "clk-gate"; + + bus-width = <8>; + cap-mmc-highspeed; + mmc-ddr-1_8v; + mmc-hs200-1_8v; + max-frequency = <200000000>; + disable-wp; + + mmc-pwrseq = <&emmc_pwrseq>; + vmmc-supply = <&vcc_3v3>; + vqmmc-supply = <&flash_1v8>; +}; + +/* + * EMMC_D4, EMMC_D5, EMMC_D6 and EMMC_D7 pins are shared between SPI NOR pins + * and eMMC Data 4 to 7 pins. + * Replace emmc_data_8b_pins to emmc_data_4b_pins from sd_emmc_c pinctrl-0, + * and change bus-width to 4 then spifc can be enabled. + * The SW1 slide should also be set to the correct position. + */ +&spifc { + status = "disabled"; + pinctrl-0 = <&nor_pins>; + pinctrl-names = "default"; + + mx25u64: spi-flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "mxicy,mx25u6435f", "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <104000000>; + }; +}; + +&tdmif_b { + status = "okay"; +}; + +&tdmout_b { + status = "okay"; +}; + +&tohdmitx { + status = "okay"; +}; + +&uart_AO { + status = "okay"; + pinctrl-0 = <&uart_ao_a_pins>; + pinctrl-names = "default"; +}; + +&usb { + status = "okay"; + vbus-supply = <&usb_pwr_en>;
arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi line 500
Quoted 10 lines
arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi new file +10
-0+}; + +&usb2_phy0 { + phy-supply = <&vcc_5v>; +}; + +&usb2_phy1 { + /* Enable the hub which is connected to this port */ + phy-supply = <&hub_5v>; +};
PATCH 2/3 dt-bindings: arm: amlogic: add support for the ODROID-N2+
In reply to Christian HewittHardKernel ODROID-N2+ uses a revised Amlogic S922X v2 chip that supports higher cpu clock speeds than the original ODROID-N2.
--- Documentation/devicetree/bindings/arm/amlogic.yaml | 1 + 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/arm/amlogic.yaml +1 -0
@@ -152,6 +152,7 @@ properties: - azw,gtking - azw,gtking-pro - hardkernel,odroid-n2 + - hardkernel,odroid-n2-plus - khadas,vim3 - ugoos,am6 - const: amlogic,s922x
Signature · 1 line
2.17.1
Re: [PATCH 2/3] dt-bindings: arm: amlogic: add support for the ODROID-N2+
Quoted 8 lines · Christian Hewitt
HardKernel ODROID-N2+ uses a revised Amlogic S922X v2 chip that supports higher cpu clock speeds than the original ODROID-N2.
Signed-off-by Christian Hewitt <[email protected]>--- Documentation/devicetree/bindings/arm/amlogic.yaml | 1 + 1 file changed, 1 insertion(+)
PATCH 3/3 arm64: dts: meson: add support for the ODROID-N2+
In reply to Christian HewittHardKernel ODROID-N2+ uses an Amlogic S922X rev. C chip capable of higher clock speeds than the original ODROID-N2. Hardkernel supports the big cpu cluster at 2.4GHz and the little cpu cluster at 2.0GHz. Opp points and regulator changess are from the HardKernel Linux kernel sources.
--- arch/arm64/boot/dts/amlogic/Makefile | 1 + .../dts/amlogic/meson-g12b-odroid-n2-plus.dts | 53 +++++++++++++++++++ 2 files changed, 54 insertions(+) create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2-plus.dts
arch/arm64/boot/dts/amlogic/Makefile +1 -0
@@ -8,6 +8,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-g12b-gtking-pro.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12b-a311d-khadas-vim3.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12b-s922x-khadas-vim3.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2.dtb +dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2-plus.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12b-ugoos-am6.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-kii-pro.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nanopi-k2.dtb
arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2-plus.dts new file +53 -0
53 lines not on this page · raw message
Signature · 1 line
2.17.1
Re: [PATCH 3/3] arm64: dts: meson: add support for the ODROID-N2+
Quoted 75 lines · Christian Hewitt
HardKernel ODROID-N2+ uses an Amlogic S922X rev. C chip capable of higher clock speeds than the original ODROID-N2. Hardkernel supports the big cpu cluster at 2.4GHz and the little cpu cluster at 2.0GHz. Opp points and regulator changess are from the HardKernel Linux kernel sources.
Suggested-by Dongjin Kim <[email protected]>Signed-off-by Christian Hewitt <[email protected]>--- arch/arm64/boot/dts/amlogic/Makefile | 1 + .../dts/amlogic/meson-g12b-odroid-n2-plus.dts | 53 +++++++++++++++++++ 2 files changed, 54 insertions(+) create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2-plus.dtsarch/arm64/boot/dts/amlogic/Makefile +1
-0@@ -8,6 +8,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-g12b-gtking-pro.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12b-a311d-khadas-vim3.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12b-s922x-khadas-vim3.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2.dtb +dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2-plus.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12b-ugoos-am6.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-kii-pro.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nanopi-k2.dtbarch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2-plus.dts new file +43
-0@@ -0,0 +1,53 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2019 BayLibre, SAS + * Author: Neil Armstrong <[email protected]> + */ + +/dts-v1/; + +#include "meson-g12b-odroid-n2.dtsi" + +/ { + compatible = "hardkernel,odroid-n2-plus", "amlogic,s922x", "amlogic,g12b"; + model = "Hardkernel ODROID-N2+"; + + vddcpu_a: regulator-vddcpu-a { + regulator-min-microvolt = <680000>; + regulator-max-microvolt = <1040000>; + + pwms = <&pwm_ab 0 1500 0>; + }; + + vddcpu_b: regulator-vddcpu-b { + regulator-min-microvolt = <680000>; + regulator-max-microvolt = <1040000>; + + pwms = <&pwm_AO_cd 1 1500 0>; + }; + + cpu_opp_table_0: opp-table-0 { + opp-1908000000 { + opp-hz = /bits/ 64 <1908000000>; + opp-microvolt = <1030000>; + }; + + opp-2016000000 { + opp-hz = /bits/ 64 <2016000000>; + opp-microvolt = <1040000>; + }; + }; + + cpub_opp_table_1: opp-table-1 { + opp-2304000000 { + opp-hz = /bits/ 64 <2304000000>;
arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2-plus.dts line 53
Quoted 10 lines
arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2-plus.dts new file +10
-0+ opp-microvolt = <1030000>; + }; + + opp-2400000000 { + opp-hz = /bits/ 64 <2400000000>; + opp-microvolt = <1040000>; + }; + }; +}; +
Re: [PATCH 3/3] arm64: dts: meson: add support for the ODROID-N2+
Quoted 79 lines · Neil Armstrong
Quoted 78 lines · Christian Hewitt
HardKernel ODROID-N2+ uses an Amlogic S922X rev. C chip capable of higher clock speeds than the original ODROID-N2. Hardkernel supports the big cpu cluster at 2.4GHz and the little cpu cluster at 2.0GHz. Opp points and regulator changess are from the HardKernel Linux kernel sources.
Suggested-by Dongjin Kim <[email protected]>Signed-off-by Christian Hewitt <[email protected]>--- arch/arm64/boot/dts/amlogic/Makefile | 1 + .../dts/amlogic/meson-g12b-odroid-n2-plus.dts | 53 +++++++++++++++++++ 2 files changed, 54 insertions(+) create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2-plus.dtsarch/arm64/boot/dts/amlogic/Makefile +1
-0@@ -8,6 +8,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-g12b-gtking-pro.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12b-a311d-khadas-vim3.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12b-s922x-khadas-vim3.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2.dtb +dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2-plus.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12b-ugoos-am6.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-kii-pro.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nanopi-k2.dtbarch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2-plus.dts new file +47
-0@@ -0,0 +1,53 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2019 BayLibre, SAS + * Author: Neil Armstrong <[email protected]> + */ + +/dts-v1/; + +#include "meson-g12b-odroid-n2.dtsi" + +/ { + compatible = "hardkernel,odroid-n2-plus", "amlogic,s922x", "amlogic,g12b"; + model = "Hardkernel ODROID-N2+"; + + vddcpu_a: regulator-vddcpu-a { + regulator-min-microvolt = <680000>; + regulator-max-microvolt = <1040000>; + + pwms = <&pwm_ab 0 1500 0>; + }; + + vddcpu_b: regulator-vddcpu-b { + regulator-min-microvolt = <680000>; + regulator-max-microvolt = <1040000>; + + pwms = <&pwm_AO_cd 1 1500 0>; + }; + + cpu_opp_table_0: opp-table-0 { + opp-1908000000 { + opp-hz = /bits/ 64 <1908000000>; + opp-microvolt = <1030000>; + }; + + opp-2016000000 { + opp-hz = /bits/ 64 <2016000000>; + opp-microvolt = <1040000>; + }; + }; + + cpub_opp_table_1: opp-table-1 { + opp-2304000000 { + opp-hz = /bits/ 64 <2304000000>; + opp-microvolt = <1030000>; + }; + + opp-2400000000 {
Quoted 9 lines
arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2-plus.dts line 53
Quoted 7 lines
arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2-plus.dts new file +6
-0+ opp-hz = /bits/ 64 <2400000000>; + opp-microvolt = <1040000>; + }; + }; +}; +Reviewed-by Neil Armstrong <[email protected]>
Wait no, it should be:
/ {
compatible = "hardkernel,odroid-n2-plus", "amlogic,s922x", "amlogic,g12b";
model = "Hardkernel ODROID-N2+";
};&vddcpu_a {
regulator-min-microvolt = <680000>;
regulator-max-microvolt = <1040000>;
pwms = <&pwm_ab 0 1500 0>;
};&vddcpu_b {
regulator-min-microvolt = <680000>;
regulator-max-microvolt = <1040000>;
pwms = <&pwm_AO_cd 1 1500 0>;
};&cpu_opp_table_0 {
opp-1908000000 {
opp-hz = /bits/ 64 <1908000000>;
opp-microvolt = <1030000>;
};
opp-2016000000 {
opp-hz = /bits/ 64 <2016000000>;
opp-microvolt = <1040000>;
};
};&cpub_opp_table_1 {
opp-2304000000 {
opp-hz = /bits/ 64 <2304000000>;
opp-microvolt = <1030000>;
};
opp-2400000000 {
opp-hz = /bits/ 64 <2400000000>;
opp-microvolt = <1040000>;
};
};Neil
Re: [PATCH 3/3] arm64: dts: meson: add support for the ODROID-N2+
Can we use "Hardkernel ODROID-N2Plus" instead of "Hardkernel ODROID-N2+"?
Thanks,
Dongjin.
Quoted 142 lines · Neil Armstrong
Quoted 79 lines · Neil Armstrong
Quoted 78 lines · Christian Hewitt
HardKernel ODROID-N2+ uses an Amlogic S922X rev. C chip capable of higher clock speeds than the original ODROID-N2. Hardkernel supports the big cpu cluster at 2.4GHz and the little cpu cluster at 2.0GHz. Opp points and regulator changess are from the HardKernel Linux kernel sources.
Suggested-by Dongjin Kim <[email protected]>Signed-off-by Christian Hewitt <[email protected]>--- arch/arm64/boot/dts/amlogic/Makefile | 1 + .../dts/amlogic/meson-g12b-odroid-n2-plus.dts | 53 +++++++++++++++++++ 2 files changed, 54 insertions(+) create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2-plus.dtsarch/arm64/boot/dts/amlogic/Makefile +1
-0@@ -8,6 +8,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-g12b-gtking-pro.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12b-a311d-khadas-vim3.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12b-s922x-khadas-vim3.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2.dtb +dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2-plus.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12b-ugoos-am6.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-kii-pro.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nanopi-k2.dtbarch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2-plus.dts new file +47
-0@@ -0,0 +1,53 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2019 BayLibre, SAS + * Author: Neil Armstrong <[email protected]> + */ + +/dts-v1/; + +#include "meson-g12b-odroid-n2.dtsi" + +/ { + compatible = "hardkernel,odroid-n2-plus", "amlogic,s922x", "amlogic,g12b"; + model = "Hardkernel ODROID-N2+"; + + vddcpu_a: regulator-vddcpu-a { + regulator-min-microvolt = <680000>; + regulator-max-microvolt = <1040000>; + + pwms = <&pwm_ab 0 1500 0>; + }; + + vddcpu_b: regulator-vddcpu-b { + regulator-min-microvolt = <680000>; + regulator-max-microvolt = <1040000>; + + pwms = <&pwm_AO_cd 1 1500 0>; + }; + + cpu_opp_table_0: opp-table-0 { + opp-1908000000 { + opp-hz = /bits/ 64 <1908000000>; + opp-microvolt = <1030000>; + }; + + opp-2016000000 { + opp-hz = /bits/ 64 <2016000000>; + opp-microvolt = <1040000>; + }; + }; + + cpub_opp_table_1: opp-table-1 { + opp-2304000000 { + opp-hz = /bits/ 64 <2304000000>; + opp-microvolt = <1030000>; + }; + + opp-2400000000 {Quoted 9 lines
arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2-plus.dts line 53
Quoted 7 lines
arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2-plus.dts new file +6
-0+ opp-hz = /bits/ 64 <2400000000>; + opp-microvolt = <1040000>; + }; + }; +}; +Reviewed-by Neil Armstrong <[email protected]>Wait no, it should be:
/ { compatible = "hardkernel,odroid-n2-plus", "amlogic,s922x", "amlogic,g12b"; model = "Hardkernel ODROID-N2+"; };&vddcpu_a { regulator-min-microvolt = <680000>; regulator-max-microvolt = <1040000>; pwms = <&pwm_ab 0 1500 0>; };&vddcpu_b { regulator-min-microvolt = <680000>; regulator-max-microvolt = <1040000>; pwms = <&pwm_AO_cd 1 1500 0>; };&cpu_opp_table_0 { opp-1908000000 { opp-hz = /bits/ 64 <1908000000>; opp-microvolt = <1030000>; }; opp-2016000000 { opp-hz = /bits/ 64 <2016000000>; opp-microvolt = <1040000>; }; };&cpub_opp_table_1 { opp-2304000000 { opp-hz = /bits/ 64 <2304000000>; opp-microvolt = <1030000>; }; opp-2400000000 { opp-hz = /bits/ 64 <2400000000>; opp-microvolt = <1040000>; }; };Neil
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Re: [PATCH 3/3] arm64: dts: meson: add support for the ODROID-N2+
In reply to Neil ArmstrongQuoted 138 lines · Neil Armstrong
Quoted 79 lines · Neil Armstrong
Quoted 78 lines · Christian Hewitt
HardKernel ODROID-N2+ uses an Amlogic S922X rev. C chip capable of higher clock speeds than the original ODROID-N2. Hardkernel supports the big cpu cluster at 2.4GHz and the little cpu cluster at 2.0GHz. Opp points and regulator changess are from the HardKernel Linux kernel sources.
Suggested-by Dongjin Kim <[email protected]>Signed-off-by Christian Hewitt <[email protected]>---
arch/arm64/boot/dts/amlogic/Makefile| 1 +.../dts/amlogic/meson-g12b-odroid-n2-plus.dts| 53 +++++++++++++++++++2 files changed, 54 insertions(+)create mode 100644
arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2-plus.dtsarch/arm64/boot/dts/amlogic/Makefile +0
-0@@ -8,6 +8,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-g12b-gtking-pro.dtbdtb-$(CONFIG_ARCH_MESON) += meson-g12b-a311d-khadas-vim3.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12b-s922x-khadas-vim3.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2.dtb +dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2-plus.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12b-ugoos-am6.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-kii-pro.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nanopi-k2.dtb
arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2-plus.dts new file +47
-0@@ -0,0 +1,53 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2019 BayLibre, SAS + * Author: Neil Armstrong <[email protected]> + */ + +/dts-v1/; + +#include "meson-g12b-odroid-n2.dtsi" + +/ { + compatible = "hardkernel,odroid-n2-plus", "amlogic,s922x", "amlogic,g12b"; + model = "Hardkernel ODROID-N2+"; + + vddcpu_a: regulator-vddcpu-a { + regulator-min-microvolt = <680000>; + regulator-max-microvolt = <1040000>; + + pwms = <&pwm_ab 0 1500 0>; + }; + + vddcpu_b: regulator-vddcpu-b { + regulator-min-microvolt = <680000>; + regulator-max-microvolt = <1040000>; + + pwms = <&pwm_AO_cd 1 1500 0>; + }; + + cpu_opp_table_0: opp-table-0 { + opp-1908000000 { + opp-hz = /bits/ 64 <1908000000>; + opp-microvolt = <1030000>; + }; + + opp-2016000000 { + opp-hz = /bits/ 64 <2016000000>; + opp-microvolt = <1040000>; + }; + }; + + cpub_opp_table_1: opp-table-1 { + opp-2304000000 { + opp-hz = /bits/ 64 <2304000000>; + opp-microvolt = <1030000>; + }; + + opp-2400000000 {Quoted 9 lines
arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2-plus.dts line 53
Quoted 7 lines
arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2-plus.dts new file +6
-0+ opp-hz = /bits/ 64 <2400000000>; + opp-microvolt = <1040000>; + }; + }; +}; +Reviewed-by Neil Armstrong <[email protected]>Wait no, it should be:
/ { compatible = "hardkernel,odroid-n2-plus", "amlogic,s922x", "amlogic,g12b"; model = "Hardkernel ODROID-N2+"; };&vddcpu_a { regulator-min-microvolt = <680000>; regulator-max-microvolt = <1040000>; pwms = <&pwm_ab 0 1500 0>; };&vddcpu_b { regulator-min-microvolt = <680000>; regulator-max-microvolt = <1040000>; pwms = <&pwm_AO_cd 1 1500 0>; };&cpu_opp_table_0 { opp-1908000000 { opp-hz = /bits/ 64 <1908000000>; opp-microvolt = <1030000>; }; opp-2016000000 { opp-hz = /bits/ 64 <2016000000>; opp-microvolt = <1040000>; }; };&cpub_opp_table_1 { opp-2304000000 { opp-hz = /bits/ 64 <2304000000>; opp-microvolt = <1030000>; }; opp-2400000000 { opp-hz = /bits/ 64 <2400000000>; opp-microvolt = <1040000>; }; };
Quoted 1 line
Neil
Okay, I will send corrected v2 and with model name changed.
Christian
Jerome Brunet
reviewerRe: [PATCH 3/3] arm64: dts: meson: add support for the ODROID-N2+
In reply to Christian HewittQuoted 72 lines · Christian Hewitt
HardKernel ODROID-N2+ uses an Amlogic S922X rev. C chip capable of higher clock speeds than the original ODROID-N2. Hardkernel supports the big cpu cluster at 2.4GHz and the little cpu cluster at 2.0GHz. Opp points and regulator changess are from the HardKernel Linux kernel sources.
Suggested-by Dongjin Kim <[email protected]>Signed-off-by Christian Hewitt <[email protected]>--- arch/arm64/boot/dts/amlogic/Makefile | 1 + .../dts/amlogic/meson-g12b-odroid-n2-plus.dts | 53 +++++++++++++++++++ 2 files changed, 54 insertions(+) create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2-plus.dtsarch/arm64/boot/dts/amlogic/Makefile +1
-0@@ -8,6 +8,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-g12b-gtking-pro.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12b-a311d-khadas-vim3.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12b-s922x-khadas-vim3.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2.dtb +dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2-plus.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12b-ugoos-am6.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-kii-pro.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nanopi-k2.dtbarch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2-plus.dts new file +41
-0@@ -0,0 +1,53 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2019 BayLibre, SAS + * Author: Neil Armstrong <[email protected]> + */ + +/dts-v1/; + +#include "meson-g12b-odroid-n2.dtsi" + +/ { + compatible = "hardkernel,odroid-n2-plus", "amlogic,s922x", "amlogic,g12b"; + model = "Hardkernel ODROID-N2+"; + + vddcpu_a: regulator-vddcpu-a { + regulator-min-microvolt = <680000>; + regulator-max-microvolt = <1040000>; + + pwms = <&pwm_ab 0 1500 0>; + }; + + vddcpu_b: regulator-vddcpu-b { + regulator-min-microvolt = <680000>; + regulator-max-microvolt = <1040000>; + + pwms = <&pwm_AO_cd 1 1500 0>; + }; + + cpu_opp_table_0: opp-table-0 { + opp-1908000000 { + opp-hz = /bits/ 64 <1908000000>; + opp-microvolt = <1030000>; + }; + + opp-2016000000 { + opp-hz = /bits/ 64 <2016000000>; + opp-microvolt = <1040000>; + }; + }; + + cpub_opp_table_1: opp-table-1 {
arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2-plus.dts line 51
Quoted 10 lines
arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2-plus.dts new file +10
-0+ opp-2304000000 { + opp-hz = /bits/ 64 <2304000000>; + opp-microvolt = <1030000>; + }; + + opp-2400000000 { + opp-hz = /bits/ 64 <2400000000>; + opp-microvolt = <1040000>; + }; + };
Are this opp specific to the N2+ or S922x rev C ? If it is the latter, shouldn't these be in s922x-revC dtsi ?
Quoted 2 lines
arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2-plus.dts new file +2
-0+}; +
Re: [PATCH 3/3] arm64: dts: meson: add support for the ODROID-N2+
Quoted 82 lines · Jerome Brunet
Quoted 77 lines · Christian Hewitt
HardKernel ODROID-N2+ uses an Amlogic S922X rev. C chip capable of higher clock speeds than the original ODROID-N2. Hardkernel supports the big cpu cluster at 2.4GHz and the little cpu cluster at 2.0GHz. Opp points and regulator changess are from the HardKernel Linux kernel sources.
Suggested-by Dongjin Kim <[email protected]>Signed-off-by Christian Hewitt <[email protected]>---
arch/arm64/boot/dts/amlogic/Makefile| 1 +.../dts/amlogic/meson-g12b-odroid-n2-plus.dts| 53 +++++++++++++++++++2 files changed, 54 insertions(+)create mode 100644
arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2-plus.dtsarch/arm64/boot/dts/amlogic/Makefile +0
-0@@ -8,6 +8,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-g12b-gtking-pro.dtbdtb-$(CONFIG_ARCH_MESON) += meson-g12b-a311d-khadas-vim3.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12b-s922x-khadas-vim3.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2.dtb +dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2-plus.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12b-ugoos-am6.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-kii-pro.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nanopi-k2.dtb
arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2-plus.dts new file +46
-0@@ -0,0 +1,53 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2019 BayLibre, SAS + * Author: Neil Armstrong <[email protected]> + */ + +/dts-v1/; + +#include "meson-g12b-odroid-n2.dtsi" + +/ { + compatible = "hardkernel,odroid-n2-plus", "amlogic,s922x", "amlogic,g12b"; + model = "Hardkernel ODROID-N2+"; + + vddcpu_a: regulator-vddcpu-a { + regulator-min-microvolt = <680000>; + regulator-max-microvolt = <1040000>; + + pwms = <&pwm_ab 0 1500 0>; + }; + + vddcpu_b: regulator-vddcpu-b { + regulator-min-microvolt = <680000>; + regulator-max-microvolt = <1040000>; + + pwms = <&pwm_AO_cd 1 1500 0>; + }; + + cpu_opp_table_0: opp-table-0 { + opp-1908000000 { + opp-hz = /bits/ 64 <1908000000>; + opp-microvolt = <1030000>; + }; + + opp-2016000000 { + opp-hz = /bits/ 64 <2016000000>; + opp-microvolt = <1040000>; + }; + }; + + cpub_opp_table_1: opp-table-1 { + opp-2304000000 { + opp-hz = /bits/ 64 <2304000000>; + opp-microvolt = <1030000>; + }; +
Quoted 8 lines
arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2-plus.dts line 51
Quoted 5 lines
arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2-plus.dts new file +5
-0+ opp-2400000000 { + opp-hz = /bits/ 64 <2400000000>; + opp-microvolt = <1040000>; + }; + };Are this opp specific to the N2+ or S922x rev C ? If it is the latter, shouldn't these be in s922x-revC dtsi ?
N2+ is currently the only known device with RevC chip (and shipping with a huge heatsink) so we don’t know. I prefer to to put them in the board dts for now and move to a common dtsi in the future once we’ve seen more devices in the wild and proven they can handle the overclock.
Christian
Re: [PATCH 3/3] arm64: dts: meson: add support for the ODROID-N2+
In reply to Christian HewittHi Christian,
Quoted 4 lines · Christian Hewitt
HardKernel ODROID-N2+ uses an Amlogic S922X rev. C chip capable of higher clock speeds than the original ODROID-N2. Hardkernel supports the big cpu cluster at 2.4GHz and the little cpu cluster at 2.0GHz. Opp points and regulator changess are from the HardKernel Linux kernel sources.
According to the ODROID wiki those values are already in the overclocking range:
https://wiki.odroid.com/odroid-n2/hardware/overclocking
From what I can tell, for ODROID-N2 upstream Linux so far used defaults from meson-g12b-s922x.dtsi, which were 1896MHz for the A53 and 1704MHz for the A73 (so it seems currently the A73 running even 100MHz below "Stock").
I guess we should pick either Stock or Overclock for the two models. Unless there is another good reason not to?
--
Stefan
Quoted 82 lines
Suggested-by Dongjin Kim <[email protected]>Signed-off-by Christian Hewitt <[email protected]>--- arch/arm64/boot/dts/amlogic/Makefile | 1 + .../dts/amlogic/meson-g12b-odroid-n2-plus.dts | 53 +++++++++++++++++++ 2 files changed, 54 insertions(+) create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2-plus.dtsarch/arm64/boot/dts/amlogic/Makefile +1
-0@@ -8,6 +8,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-g12b-gtking-pro.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12b-a311d-khadas-vim3.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12b-s922x-khadas-vim3.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2.dtb +dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2-plus.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12b-ugoos-am6.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-kii-pro.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nanopi-k2.dtbarch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2-plus.dts new file +53
-0@@ -0,0 +1,53 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2019 BayLibre, SAS + * Author: Neil Armstrong <[email protected]> + */ + +/dts-v1/; + +#include "meson-g12b-odroid-n2.dtsi" + +/ { + compatible = "hardkernel,odroid-n2-plus", "amlogic,s922x", "amlogic,g12b"; + model = "Hardkernel ODROID-N2+"; + + vddcpu_a: regulator-vddcpu-a { + regulator-min-microvolt = <680000>; + regulator-max-microvolt = <1040000>; + + pwms = <&pwm_ab 0 1500 0>; + }; + + vddcpu_b: regulator-vddcpu-b { + regulator-min-microvolt = <680000>; + regulator-max-microvolt = <1040000>; + + pwms = <&pwm_AO_cd 1 1500 0>; + }; + + cpu_opp_table_0: opp-table-0 { + opp-1908000000 { + opp-hz = /bits/ 64 <1908000000>; + opp-microvolt = <1030000>; + }; + + opp-2016000000 { + opp-hz = /bits/ 64 <2016000000>; + opp-microvolt = <1040000>; + }; + }; + + cpub_opp_table_1: opp-table-1 { + opp-2304000000 { + opp-hz = /bits/ 64 <2304000000>; + opp-microvolt = <1030000>; + }; + + opp-2400000000 { + opp-hz = /bits/ 64 <2400000000>; + opp-microvolt = <1040000>; + }; + }; +}; +