Skip to contentSkip to conversation

USB mass storage device problem

DISCUSSION jim beam 2 participants 2 messages Nov 12, 2003

lore
Share & tools
lore

jim beam

author
#0 lore raw

Hello,

I am attempting to get a CompactFlash reader to work (Soyo SB-K7VXBP). The device sits in a 3.5" bay and plugs directly into a USB1 connector on my motherboard. It also provides two USB ports, which work.

The CompactFlash reader almost works. At bootup, I get this message:

hub 3-0:1.0: new USB device on port 1, assigned address 2 scsi0 : SCSI emulation for USB Mass Storage devices
Vendor: SOYO Model: USB Storage-SMC Rev: 0214
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
WARNING: USB Mass Storage data integrity not assured USB Mass Storage device found at 2

The device shows up in /sys/block/sda and in /sys/bus/usb/drivers/usb-storage. Also, /dev/sda is created as a symlink to /dev/scsi/host0/bus0/target0/lun0/disc (I am using devfs).

However, when try to mount /dev/sda, I get an error saying "No medium found". I have tried inserting the card after booting and also before booting, with the same result. I am using the 2.6.0-test9 kernel, but I have had this device since early 2.4 and it has never worked. It is not damaged hardware because Windows detects it as a drive.

Trying to run fdisk on /dev/sda gives the message "Unable to open /dev/sda".
Is there something else I need to do, or any more information I can
provide to debug this problem?

Thanks,
Jim

_________________________________________________________________
Is your computer infected with a virus? Find out with a FREE computer virus scan from McAfee. Take the FreeScan now! http://clinic.mcafee.com/clinic/ibuy/campaign.asp?cid=3963

#1 lore raw

You're talking to the first (and wrong) LUN of a multi-LUN device.

You can:
(1) Use a SCSI module option to set the number of LUNs higher
(2) Do an echo "scsi add-single-device 0 0 0 1" > /proc/scsi/scsi

Matt

Quoted 43 lines · jim beam

Hello,

I am attempting to get a CompactFlash reader to work (Soyo SB-K7VXBP). The device sits in a 3.5" bay and plugs directly into a USB1 connector on my motherboard. It also provides two USB ports, which work.

The CompactFlash reader almost works. At bootup, I get this message:

hub 3-0:1.0: new USB device on port 1, assigned address 2 scsi0 : SCSI emulation for USB Mass Storage devices
Vendor: SOYO Model: USB Storage-SMC Rev: 0214
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
WARNING: USB Mass Storage data integrity not assured USB Mass Storage device found at 2

The device shows up in /sys/block/sda and in /sys/bus/usb/drivers/usb-storage. Also, /dev/sda is created as a symlink to /dev/scsi/host0/bus0/target0/lun0/disc (I am using devfs).

However, when try to mount /dev/sda, I get an error saying "No medium found". I have tried inserting the card after booting and also before booting, with the same result. I am using the 2.6.0-test9 kernel, but I have had this device since early 2.4 and it has never worked. It is not damaged hardware because Windows detects it as a drive.

Trying to run fdisk on /dev/sda gives the message "Unable to open /dev/sda".
Is there something else I need to do, or any more information I can
provide to debug this problem?

Thanks,
Jim

_________________________________________________________________
Is your computer infected with a virus? Find out with a FREE computer virus scan from McAfee. Take the FreeScan now!
http://clinic.mcafee.com/clinic/ibuy/campaign.asp?cid=3963

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

Signature · 6 lines
Matthew Dharm                              Home: [email protected] 
Maintainer, Linux USB Mass Storage Driver

It's monday.  It must be monday.
					-- Greg
User Friendly, 5/4/1998