Skip to contentSkip to conversation

arm64: dts: rockchip: Update eMMC for NanoPi R5 series

PATCH Applied Peter Robinson 3 participants 3 messages May 6, 2025 – May 8, 2025

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 arm64: dts: rockchip: Update eMMC for NanoPi R5 series

Add the 3.3v and 1.8v regulators that are connected to the eMMC on the R5 series devices, as well as adding the eMMC data strobe, and enable eMMC HS200 mode as the Foresee FEMDNN0xxG-A3A55 modules support it.

Fixes c8ec73b05a95d ("arm64: dts: rockchip: create common dtsi for NanoPi R5 series")

---

I had reports from some Fedora users that their eMMC didn't work on the R5C and this fixes it, the schematic of the eMMC is the same across all of the R5 series of devices.

 arch/arm64/boot/dts/rockchip/rk3568-nanopi-r5s.dtsi | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)
arch/arm64/boot/dts/rockchip/rk3568-nanopi-r5s.dtsi +4 -1
index 00c479aa18711..a28b4af10d13a 100644
@@ -486,9 +486,12 @@ &saradc {
 &sdhci {
 	bus-width = <8>;
 	max-frequency = <200000000>;
+	mmc-hs200-1_8v;
 	non-removable;
 	pinctrl-names = "default";
-	pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd>;
+	pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd &emmc_datastrobe>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vcc_1v8>;
 	status = "okay";
 };
 
Signature · 1 line
2.49.0
Reviewed-by on v1 1/1
#1 lore raw
Quoted 4 lines · Peter Robinson

Add the 3.3v and 1.8v regulators that are connected to the eMMC on the R5 series devices, as well as adding the eMMC data strobe, and enable eMMC HS200 mode as the Foresee FEMDNN0xxG-A3A55 modules support it.

Foresee eMMC FEMDNN032G-A3A55 datasheet version 1.2 dd 2021-05-17 mentions on page 4 that it supports HS400 and HS200.
It also mentions in paragraph 5.2 "Power Consumption" on page 6 that ``Vcc`` uses 3.3V and ``Vccq`` uses 1.8V.

In chapter 6 "Pin Assignment" on page 7 we can see the following pin assignments in "FBGA153 - Ball Array":

Vcc: E6+F5+J10+K9
Vccq: C6+M4+N4+P3+P5
Data Strobe(DS): H5

In the NanoPi R5S schematic version 2204 on page 23 we can see eMMC_153FBGA/U9501 described.

Pins E6+F5+J10+K9 are all labeled ``VDDF`` and those are connected to ``VCC3V3_FLASH`` which is connected to ``VCC_3V3``.

Pins C6+M4+N4+P3+P5 are all labeled ``VDD`` and those are connected to ``VCCIO_FLASH`` which is connected to ``VCC_1V8``.

Pin H5 is labeled ``Data Strobe`` and is connected to ``eMMC_DATA_STROBE/FLASH_CLE`` which is connected to GPIO1_C6 which corresponds to ``emmc_datastrobe`` in ``rk3568-pinctrl.dtsi``.

In the NanoPi R5C schematic version 2209 on page 22 we see the same pins labeled ``VDDF`` and also for ``VDD``, but here they are (directly) connected to ``VCC_3V3`` and ``VCC_1V8`` respectively.

Quoted 16 lines
Fixes c8ec73b05a95d ("arm64: dts: rockchip: create common dtsi for NanoPi R5 series")

---

I had reports from some Fedora users that their eMMC didn't work on the R5C and this fixes it, the schematic of the eMMC is the same across all of the R5 series of devices.

 arch/arm64/boot/dts/rockchip/rk3568-nanopi-r5s.dtsi | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)
arch/arm64/boot/dts/rockchip/rk3568-nanopi-r5s.dtsi +0 -0
index 00c479aa18711..a28b4af10d13a 100644

arch/arm64/boot/dts/rockchip/rk3568-nanopi-r5s.dtsi &saradc { · line 494

Quoted 10 lines
arch/arm64/boot/dts/rockchip/rk3568-nanopi-r5s.dtsi +4 -1
@@ -486,9 +486,12 @@ &saradc {
 &sdhci {
 	bus-width = <8>;
 	max-frequency = <200000000>;
+	mmc-hs200-1_8v;
 	non-removable;
 	pinctrl-names = "default";
-	pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd>;
+	pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd &emmc_datastrobe>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vcc_1v8>;

The above is correctly describe in the dtsi file, so

Quoted 3 lines
arch/arm64/boot/dts/rockchip/rk3568-nanopi-r5s.dtsi +0 -0
 	status = "okay";
 };
 
maintainer Applied
#2 lore raw
In reply to Peter Robinson
Quoted 6 lines · Peter Robinson

Add the 3.3v and 1.8v regulators that are connected to the eMMC on the R5 series devices, as well as adding the eMMC data strobe, and enable eMMC HS200 mode as the Foresee FEMDNN0xxG-A3A55 modules support it.

Applied, thanks!

[1/1] arm64: dts: rockchip: Update eMMC for NanoPi R5 series

      commit: 8eca9e979a1efbcc3d090f6eb3f4da621e7c87e0

Best regards,

Signature · 1 line
Heiko Stuebner <[email protected]>