Skip to contentSkip to conversation

phy: qualcomm: phy-qcom-eusb2-repeater: fix override properties

PATCH Applied Pengyu Luo 4 participants 4 messages Aug 12, 2025

Subsystems (2)
lore
Share & tools
lore

Pengyu Luo

author
#0 lore raw

PATCH 1/1 phy: qualcomm: phy-qcom-eusb2-repeater: fix override properties

property "qcom,tune-usb2-preem" is for EUSB2_TUNE_USB2_PREEM property "qcom,tune-usb2-amplitude" is for EUSB2_TUNE_IUSB2

The downstream correspondence is as follows:
EUSB2_TUNE_USB2_PREEM: Tx pre-emphasis tuning
EUSB2_TUNE_IUSB2: HS trasmit amplitude
EUSB2_TUNE_SQUELCH_U: Squelch detection threshold
EUSB2_TUNE_HSDISC: HS disconnect threshold
EUSB2_TUNE_EUSB_SLEW: slew rate

Fixes 31bc94de7602 ("phy: qualcomm: phy-qcom-eusb2-repeater: Don't zero-out registers")
---
 drivers/phy/qualcomm/phy-qcom-eusb2-repeater.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/phy/qualcomm/phy-qcom-eusb2-repeater.c +2 -2
index d7493c229..3709fba42 100644
@@ -127,13 +127,13 @@ static int eusb2_repeater_init(struct phy *phy)
 			     rptr->cfg->init_tbl[i].value);
 
 	/* Override registers from devicetree values */
-	if (!of_property_read_u8(np, "qcom,tune-usb2-amplitude", &val))
+	if (!of_property_read_u8(np, "qcom,tune-usb2-preem", &val))
 		regmap_write(regmap, base + EUSB2_TUNE_USB2_PREEM, val);
 
 	if (!of_property_read_u8(np, "qcom,tune-usb2-disc-thres", &val))
 		regmap_write(regmap, base + EUSB2_TUNE_HSDISC, val);
 
-	if (!of_property_read_u8(np, "qcom,tune-usb2-preem", &val))
+	if (!of_property_read_u8(np, "qcom,tune-usb2-amplitude", &val))
 		regmap_write(regmap, base + EUSB2_TUNE_IUSB2, val);
 
 	/* Wait for status OK */
Signature · 1 line
2.50.1
Reviewed-by on v1 1/1
#1 lore raw
Quoted 9 lines · Pengyu Luo

property "qcom,tune-usb2-preem" is for EUSB2_TUNE_USB2_PREEM property "qcom,tune-usb2-amplitude" is for EUSB2_TUNE_IUSB2

The downstream correspondence is as follows:
EUSB2_TUNE_USB2_PREEM: Tx pre-emphasis tuning
EUSB2_TUNE_IUSB2: HS trasmit amplitude
EUSB2_TUNE_SQUELCH_U: Squelch detection threshold
EUSB2_TUNE_HSDISC: HS disconnect threshold
EUSB2_TUNE_EUSB_SLEW: slew rate

The commit message is a bit.. dry.. but I suppose it conveys what the problem is

Quoted 4 lines
Fixes 31bc94de7602 ("phy: qualcomm: phy-qcom-eusb2-repeater: Don't zero-out registers")

---

Konrad

Reviewed-by on v1 1/1
#2 lore raw
In reply to Pengyu Luo
Quoted 11 lines · Pengyu Luo

property "qcom,tune-usb2-preem" is for EUSB2_TUNE_USB2_PREEM property "qcom,tune-usb2-amplitude" is for EUSB2_TUNE_IUSB2

The downstream correspondence is as follows:
EUSB2_TUNE_USB2_PREEM: Tx pre-emphasis tuning
EUSB2_TUNE_IUSB2: HS trasmit amplitude
EUSB2_TUNE_SQUELCH_U: Squelch detection threshold
EUSB2_TUNE_HSDISC: HS disconnect threshold
EUSB2_TUNE_EUSB_SLEW: slew rate

Fixes 31bc94de7602 ("phy: qualcomm: phy-qcom-eusb2-repeater: Don't zero-out registers")

Oh, not sure how this happened. Thanks for catching this, I do see the problem in my original commit.

Regards
Luca

Quoted 25 lines
---
 drivers/phy/qualcomm/phy-qcom-eusb2-repeater.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/phy/qualcomm/phy-qcom-eusb2-repeater.c +2 -2
index d7493c229..3709fba42 100644
@@ -127,13 +127,13 @@ static int eusb2_repeater_init(struct phy *phy)
 			     rptr->cfg->init_tbl[i].value);
 
 	/* Override registers from devicetree values */
-	if (!of_property_read_u8(np, "qcom,tune-usb2-amplitude", &val))
+	if (!of_property_read_u8(np, "qcom,tune-usb2-preem", &val))
 		regmap_write(regmap, base + EUSB2_TUNE_USB2_PREEM, val);
 
 	if (!of_property_read_u8(np, "qcom,tune-usb2-disc-thres", &val))
 		regmap_write(regmap, base + EUSB2_TUNE_HSDISC, val);
 
-	if (!of_property_read_u8(np, "qcom,tune-usb2-preem", &val))
+	if (!of_property_read_u8(np, "qcom,tune-usb2-amplitude", &val))
 		regmap_write(regmap, base + EUSB2_TUNE_IUSB2, val);
 
 	/* Wait for status OK */
maintainer Applied
#3 lore raw
In reply to Pengyu Luo
Quoted 11 lines · Pengyu Luo

property "qcom,tune-usb2-preem" is for EUSB2_TUNE_USB2_PREEM property "qcom,tune-usb2-amplitude" is for EUSB2_TUNE_IUSB2

The downstream correspondence is as follows:
EUSB2_TUNE_USB2_PREEM: Tx pre-emphasis tuning
EUSB2_TUNE_IUSB2: HS trasmit amplitude
EUSB2_TUNE_SQUELCH_U: Squelch detection threshold
EUSB2_TUNE_HSDISC: HS disconnect threshold
EUSB2_TUNE_EUSB_SLEW: slew rate

[...]

Applied, thanks!

[1/1] phy: qualcomm: phy-qcom-eusb2-repeater: fix override properties

      commit: 942e47ab228c7dd27c2ae043c17e7aab2028082c

Best regards,

Signature · 1 line
~Vinod