Skip to contentSkip to conversation

Testing Phosphor-pid-control

DISCUSSION Vijay Khemka 4 participants 8 messages Dec 20, 2018 – Jan 2, 2019

lore
Share & tools
lore
#0 lore raw

Team,
I am using phosphor-pid-control for controlling fan, how do I test this to verify if it is driving pwm correctly. Any ways to fake temperature and see if fan speeds changes.

Regards
-Vijay

#1 lore raw

Assuming you’re using dbus-sensors (which I’m pretty sure you are):

Support for overriding sensor values was recently landed in this commit:
https://gerrit.openbmc-project.xyz/#/c/openbmc/dbus-sensors/+/16177/

Overriding a sensor value with a "fake" sensor reading should be as easy as simply calling SetProperty on the dbus interface.

Example as tested on my system (your path names may vary)
dbus-send --system --print-reply --dest=xyz.openbmc_project.CPUSensor /xyz/openbmc_project/sensors/temperature/Core_1_CPU0 org.freedesktop.DBus.Properties.Set string:xyz.openbmc_project.Sensor.Value string:Value variant:double:1.0

and verify by reading it back out:

dbus-send --system --print-reply --dest=xyz.openbmc_project.CPUSensor /xyz/openbmc_project/sensors/temperature/Core_1_CPU0 org.freedesktop.DBus.Properties.GetAll string:xyz.openbmc_project.Sensor.Value

method return time=1543267812.458169 sender=:1.16 -> destination=:1.153 serial=6398 reply_serial=2
array [

      dict entry(
         string "MaxValue"
         variant             double 127
      )
      dict entry(
         string "MinValue"
         variant             double -128
      )
      dict entry(
         string "Value"
         variant             double 1
      )

]

#2 lore raw

Hi Ed,
I am able to override and read it back but not seeing any change in pwm data as well as fan speed. I have swampd running.

Regards
-Vijay

On 12/20/18, 10:14 AM, "Tanous, Ed" <[email protected]> wrote:

Assuming you’re using dbus-sensors (which I’m pretty sure you are):

Support for overriding sensor values was recently landed in this commit:
https://urldefense.proofpoint.com/v2/url?u=https-3A__gerrit.openbmc-2Dproject.xyz_-23_c_openbmc_dbus-2Dsensors_-2B_16177_&d=DwIGaQ&c=5VD0RTtNlTh3ycd41b3MUw&r=v9MU0Ki9pWnTXCWwjHPVgpnCR80vXkkcrIaqU7USl5g&m=1J-5eJl4Drc2LKcQ2SdONc02uR5cih3P68m66QcMYog&s=c9798qmI_pA3hnzB97oaYFK8yFTmwrxdpAeRrui4qkY&e=

Overriding a sensor value with a "fake" sensor reading should be as easy as simply calling SetProperty on the dbus interface.

Example as tested on my system (your path names may vary)
dbus-send --system --print-reply --dest=xyz.openbmc_project.CPUSensor /xyz/openbmc_project/sensors/temperature/Core_1_CPU0 org.freedesktop.DBus.Properties.Set string:xyz.openbmc_project.Sensor.Value string:Value variant:double:1.0

and verify by reading it back out:

dbus-send --system --print-reply --dest=xyz.openbmc_project.CPUSensor /xyz/openbmc_project/sensors/temperature/Core_1_CPU0 org.freedesktop.DBus.Properties.GetAll string:xyz.openbmc_project.Sensor.Value

#3 lore raw
Quoted 3 lines · Vijay Khemka

Hi Ed,
I am able to override and read it back but not seeing any change in pwm data as well as fan speed. I have swampd running.

You mean the dbus reads of the values aren't changing? I'm not as familiar with the dbus-sensor integration beyond run-time configuration, versus run-time state. Swampd itself doesn't expose PID information or set-point information unless that's done in the step controller (and I didn't see that aspect in that object).

Or are you saying that the fan speeds aren't changing when you read the hwmon values?

Quoted 21 lines

Regards
-Vijay

On 12/20/18, 10:14 AM, "Tanous, Ed" <[email protected]> wrote:

Assuming you’re using dbus-sensors (which I’m pretty sure you are):

Support for overriding sensor values was recently landed in this commit:
https://urldefense.proofpoint.com/v2/url?u=https-3A__gerrit.openbmc-2Dproject.xyz_-23_c_openbmc_dbus-2Dsensors_-2B_16177_&d=DwIGaQ&c=5VD0RTtNlTh3ycd41b3MUw&r=v9MU0Ki9pWnTXCWwjHPVgpnCR80vXkkcrIaqU7USl5g&m=1J-5eJl4Drc2LKcQ2SdONc02uR5cih3P68m66QcMYog&s=c9798qmI_pA3hnzB97oaYFK8yFTmwrxdpAeRrui4qkY&e=

Overriding a sensor value with a "fake" sensor reading should be as easy as simply calling SetProperty on the dbus interface.

Example as tested on my system (your path names may vary)
dbus-send --system --print-reply --dest=xyz.openbmc_project.CPUSensor /xyz/openbmc_project/sensors/temperature/Core_1_CPU0 org.freedesktop.DBus.Properties.Set string:xyz.openbmc_project.Sensor.Value string:Value variant:double:1.0

and verify by reading it back out:

dbus-send --system --print-reply --dest=xyz.openbmc_project.CPUSensor /xyz/openbmc_project/sensors/temperature/Core_1_CPU0 org.freedesktop.DBus.Properties.GetAll string:xyz.openbmc_project.Sensor.Value

#4 lore raw

Hi Patrick,
I am not seeing any change in fan speed when I read hwmon values. Can you please give me any formula how it is using data to change speed. Because I tried faking several temperatures and finally could make this change when I bring temperature below 10 but it doesn't change when I take temperature to more than max value.

Regards
-Vijay

On 12/28/18, 1:50 AM, "Patrick Venture" <[email protected]> wrote:

On Thu, Dec 20, 2018 at 12:57 PM Vijay Khemka <[email protected]> wrote:
>
> Hi Ed,
> I am able to override and read it back but not seeing any change in pwm data as well as fan speed. I have swampd running.

You mean the dbus reads of the values aren't changing? I'm not as familiar with the dbus-sensor integration beyond run-time configuration, versus run-time state. Swampd itself doesn't expose PID information or set-point information unless that's done in the step controller (and I didn't see that aspect in that object).

Or are you saying that the fan speeds aren't changing when you read the hwmon values?

>
> Regards
> -Vijay
>
> On 12/20/18, 10:14 AM, "Tanous, Ed" <[email protected]> wrote:
>
> Assuming you’re using dbus-sensors (which I’m pretty sure you are):
>
> Support for overriding sensor values was recently landed in this commit:
> https://urldefense.proofpoint.com/v2/url?u=https-3A__gerrit.openbmc-2Dproject.xyz_-23_c_openbmc_dbus-2Dsensors_-2B_16177_&d=DwIGaQ&c=5VD0RTtNlTh3ycd41b3MUw&r=v9MU0Ki9pWnTXCWwjHPVgpnCR80vXkkcrIaqU7USl5g&m=1J-5eJl4Drc2LKcQ2SdONc02uR5cih3P68m66QcMYog&s=c9798qmI_pA3hnzB97oaYFK8yFTmwrxdpAeRrui4qkY&e=
>
> Overriding a sensor value with a "fake" sensor reading should be as easy as simply calling SetProperty on the dbus interface.
>
> Example as tested on my system (your path names may vary)
> dbus-send --system --print-reply --dest=xyz.openbmc_project.CPUSensor /xyz/openbmc_project/sensors/temperature/Core_1_CPU0 org.freedesktop.DBus.Properties.Set string:xyz.openbmc_project.Sensor.Value string:Value variant:double:1.0
>
> and verify by reading it back out:
>
> dbus-send --system --print-reply --dest=xyz.openbmc_project.CPUSensor /xyz/openbmc_project/sensors/temperature/Core_1_CPU0 org.freedesktop.DBus.Properties.GetAll string:xyz.openbmc_project.Sensor.Value
>
>

#5 lore raw
Quoted 3 lines · Vijay Khemka

Hi Patrick,
I am not seeing any change in fan speed when I read hwmon values. Can you please give me any formula how it is using data to change speed. Because I tried faking several temperatures and finally could make this change when I bring temperature below 10 but it doesn't change when I take temperature to more than max value.

Which PID controller are you using? If you only have sensors configured then there's nothing to push the changes, presumably you have a PID added. Depending on which you chose, depends on what's happening with it -- that's why I'm asking for more. The formula for the "normal" pid controller is such that it tries to reduce the "error" between the set-point and the real fan speeds.

https://github.com/openbmc/phosphor-pid-control/blob/master/pid/ec/pid.cpp#L43

There's also a step-wise controller option, which is why I'm asking.

Quoted 43 lines

Regards
-Vijay

On 12/28/18, 1:50 AM, "Patrick Venture" <[email protected]> wrote:

On Thu, Dec 20, 2018 at 12:57 PM Vijay Khemka <[email protected]> wrote:
>
> Hi Ed,
> I am able to override and read it back but not seeing any change in pwm data as well as fan speed. I have swampd running.

You mean the dbus reads of the values aren't changing? I'm not as familiar with the dbus-sensor integration beyond run-time configuration, versus run-time state. Swampd itself doesn't expose PID information or set-point information unless that's done in the step controller (and I didn't see that aspect in that object).

Or are you saying that the fan speeds aren't changing when you read the hwmon values?

>
> Regards
> -Vijay
>
> On 12/20/18, 10:14 AM, "Tanous, Ed" <[email protected]> wrote:
>
> Assuming you’re using dbus-sensors (which I’m pretty sure you are):
>
> Support for overriding sensor values was recently landed in this commit:
> https://urldefense.proofpoint.com/v2/url?u=https-3A__gerrit.openbmc-2Dproject.xyz_-23_c_openbmc_dbus-2Dsensors_-2B_16177_&d=DwIGaQ&c=5VD0RTtNlTh3ycd41b3MUw&r=v9MU0Ki9pWnTXCWwjHPVgpnCR80vXkkcrIaqU7USl5g&m=1J-5eJl4Drc2LKcQ2SdONc02uR5cih3P68m66QcMYog&s=c9798qmI_pA3hnzB97oaYFK8yFTmwrxdpAeRrui4qkY&e=
>
> Overriding a sensor value with a "fake" sensor reading should be as easy as simply calling SetProperty on the dbus interface.
>
> Example as tested on my system (your path names may vary)
> dbus-send --system --print-reply --dest=xyz.openbmc_project.CPUSensor /xyz/openbmc_project/sensors/temperature/Core_1_CPU0 org.freedesktop.DBus.Properties.Set string:xyz.openbmc_project.Sensor.Value string:Value variant:double:1.0
>
> and verify by reading it back out:
>
> dbus-send --system --print-reply --dest=xyz.openbmc_project.CPUSensor /xyz/openbmc_project/sensors/temperature/Core_1_CPU0 org.freedesktop.DBus.Properties.GetAll string:xyz.openbmc_project.Sensor.Value
>
>

#6 lore raw

On 1/2/19, 11:05 AM, "Patrick Venture" <[email protected]> wrote:

On Wed, Jan 2, 2019 at 11:00 AM Vijay Khemka <[email protected]> wrote:
>
> Hi Patrick,
> I am not seeing any change in fan speed when I read hwmon values. Can you please give me any formula how it is using data to change speed. Because I tried faking several temperatures and finally could make this change when I bring temperature below 10 but it doesn't change when I take temperature to more than max value.

Which PID controller are you using? If you only have sensors configured then there's nothing to push the changes, presumably you have a PID added. Depending on which you chose, depends on what's happening with it -- that's why I'm asking for more. The formula for the "normal" pid controller is such that it tries to reduce the "error" between the set-point and the real fan speeds.

I am using basic configuration for pid as below. I may have to revisit these data, please advise if I am missing anything here.

        {   
            "Class": "fan",
            "FFGainCoefficient": 0.01,
            "FFOffCoefficient": 0.0,
            "ICoefficient": 0.0,
            "ILimitMax": 0.0,
            "ILimitMin": 0.0,
            "Inputs": [
                "MB_FAN0_TACH"
            ],  
            "Name": "MB_FAN0_TACH",
            "OutLimitMax": 100.0,
            "OutLimitMin": 30.0,
            "Outputs": [
                "Pwm 1"
            ],
            "PCoefficient": 0.0,
            "SlewNeg": 0.0,
            "SlewPos": 0.0,
            "Type": "Pid",
            "Zones": [
                "Pid 1"
            ]
        },  

    
    https://github.com/openbmc/phosphor-pid-control/blob/master/pid/ec/pid.cpp#L43
    
    There's also a step-wise controller option, which is why I'm asking.

How to configure step-wise controller as we need for linear configuration as well.

Quoted 43 lines

Regards
-Vijay

On 12/28/18, 1:50 AM, "Patrick Venture" <[email protected]> wrote:

On Thu, Dec 20, 2018 at 12:57 PM Vijay Khemka <[email protected]> wrote:
>
> Hi Ed,
> I am able to override and read it back but not seeing any change in pwm data as well as fan speed. I have swampd running.

You mean the dbus reads of the values aren't changing? I'm not as familiar with the dbus-sensor integration beyond run-time configuration, versus run-time state. Swampd itself doesn't expose PID information or set-point information unless that's done in the step controller (and I didn't see that aspect in that object).

Or are you saying that the fan speeds aren't changing when you read the hwmon values?

>
> Regards
> -Vijay
>
> On 12/20/18, 10:14 AM, "Tanous, Ed" <[email protected]> wrote:
>
> Assuming you’re using dbus-sensors (which I’m pretty sure you are):
>
> Support for overriding sensor values was recently landed in this commit:
> https://urldefense.proofpoint.com/v2/url?u=https-3A__gerrit.openbmc-2Dproject.xyz_-23_c_openbmc_dbus-2Dsensors_-2B_16177_&d=DwIGaQ&c=5VD0RTtNlTh3ycd41b3MUw&r=v9MU0Ki9pWnTXCWwjHPVgpnCR80vXkkcrIaqU7USl5g&m=1J-5eJl4Drc2LKcQ2SdONc02uR5cih3P68m66QcMYog&s=c9798qmI_pA3hnzB97oaYFK8yFTmwrxdpAeRrui4qkY&e=
>
> Overriding a sensor value with a "fake" sensor reading should be as easy as simply calling SetProperty on the dbus interface.
>
> Example as tested on my system (your path names may vary)
> dbus-send --system --print-reply --dest=xyz.openbmc_project.CPUSensor /xyz/openbmc_project/sensors/temperature/Core_1_CPU0 org.freedesktop.DBus.Properties.Set string:xyz.openbmc_project.Sensor.Value string:Value variant:double:1.0
>
> and verify by reading it back out:
>
> dbus-send --system --print-reply --dest=xyz.openbmc_project.CPUSensor /xyz/openbmc_project/sensors/temperature/Core_1_CPU0 org.freedesktop.DBus.Properties.GetAll string:xyz.openbmc_project.Sensor.Value
>
>