fdisk: "File size limit exceeded on fdisk" 2.4.10 to 2.4.13-pre6
Hi everybody
When I try to create a partition of 2GB using fdisk or parted, I get the error "File size limit exceeded (core dumped)". I already read about this error on the mailing list, but sadly not of any solution.
Has anybody got one?
Btw: If happend with fdisk from util-linux-2.10f until util-linux-2.11l.
P.S. I'm not subscribed to the list bla bla bla (but read it rather often).
Bye
Tim
Quoted 3 lines
When I try to create a partition of 2GB using fdisk or parted, I get the error "File size limit exceeded (core dumped)". I already read about this error on the mailing list, but sadly not of any solution.
Make sure you have limits set right and a new enough glibc.
Quoted 1 line · On Wed, 24 Oct 2001 16:27:44 +0100 (BST) Alan Cox <[email protected]>…
Quoted 1 line
When I try to create a partition of 2GB using fdisk or parted, I get
the
Quoted 1 line
Quoted 1 line
error "File size limit exceeded (core dumped)". I already read about
this
Quoted 3 lines
Quoted 1 line
error on the mailing list, but sadly not of any solution.
Make sure you have limits set right and a new enough glibc.
I'm using a Red Hat 6.2 system with glibc 2.1.3 (glibc-2.1.3-22), the latest for Red Hat 6.2. Switching to 7.x would mean to upgrade the whole system, I guess I can't just take the glibc rpm out of 7.x and everything still runs fine?
So that means I'm really fucked?
Bye
Tim
Quoted 6 lines
I'm using a Red Hat 6.2 system with glibc 2.1.3 (glibc-2.1.3-22), the latest for Red Hat 6.2. Switching to 7.x would mean to upgrade the whole system, I guess I can't just take the glibc rpm out of 7.x and everything still runs fine?
So that means I'm really fucked?
glibc 2.1.x has minimal support for 64bit file size handling. You probably need to build 64bit aware tools. You might also be hitting a device bug that seems to be in Linus kernel where devices are inheriting the file size limit of the underlying fs the /dev node is on. However I thought that was long fixed.
Quoted 1 line · On Wed, 24 Oct 2001 17:01:37 +0100 (BST) Alan Cox <[email protected]>…
glibc 2.1.x has minimal support for 64bit file size handling. You
probably
Quoted 1 line
need to build 64bit aware tools. You might also be hitting a device bug
that
Quoted 1 line
seems to be in Linus kernel where devices are inheriting the file size
limit
Quoted 1 line
of the underlying fs the /dev node is on. However I thought that was
long
Quoted 2 lines
fixed.
The latter seems to be the case because Vita Samel (hope I got this right) just reported that "Booting into 2.4.10-ac10" fixed the problem. Perhaps it once was fixed and later defixed?
Bye
Tim
Quoted 3 lines
The latter seems to be the case because Vita Samel (hope I got this right) just reported that "Booting into 2.4.10-ac10" fixed the problem. Perhaps it once was fixed and later defixed?
Sounds like it. I'll have a look some point next week to see if I can see what is up
Quoted 6 lines · Alan Cox
Quoted 3 lines
The latter seems to be the case because Vita Samel (hope I got this right) just reported that "Booting into 2.4.10-ac10" fixed the problem. Perhaps it once was fixed and later defixed?
Sounds like it. I'll have a look some point next week to see if I can see what is up
I'm able fdisk/mke2fs with 2.4.13-pre6 without the error so long as I don't touch the device with hdparm.
Signature · 8 lines
=====================================================================
Mohammad A. Haque http://www.haque.net/
[email protected]
"Alcohol and calculus don't mix. Developer/Project Lead
Don't drink and derive." --Unknown http://wm.themes.org/
[email protected]
=====================================================================Quoted 3 lines · On Wed, 24 Oct 2001 12:28:05 -0400 (EDT) "Mohammad A. Haque"…
Quoted 1 line · Alan Cox
Quoted 1 line
The latter seems to be the case because Vita Samel (hope I got this
right)
Quoted 1 line
Quoted 1 line
Quoted 1 line
just reported that "Booting into 2.4.10-ac10" fixed the problem.
Perhaps
Quoted 3 lines
Quoted 3 lines
Quoted 1 line
it once was fixed and later defixed?
Sounds like it. I'll have a look some point next week to see if I can
see
Quoted 4 lines
Quoted 1 line
what is up
I'm able fdisk/mke2fs with 2.4.13-pre6 without the error so long as I don't touch the device with hdparm.
Well I do use hdparm -d 1 /dev/hda in init to set dma to 1. I know called hdparm -d 0 /dev/hda and tried again, but it still fails. Do you mean hdparm should not touch the device at all and a reboot without the hdparm -d 1 /dev/hda would do the job? I could live with that for the moment, as I don't have to repartition my drive very often...
Bye
Tim
Quoted 12 lines
Signature · 10 lines
-- ===================================================================== Mohammad A. Haque http://www.haque.net/ [email protected] "Alcohol and calculus don't mix. Developer/Project Lead Don't drink and derive." --Unknown http://wm.themes.org/ [email protected] =====================================================================
Quoted 8 lines · Tim Tassonis
Quoted 2 lines
I'm able fdisk/mke2fs with 2.4.13-pre6 without the error so long as I don't touch the device with hdparm.
Well I do use hdparm -d 1
/dev/hdain init to set dma to 1. I know called hdparm -d 0/dev/hdaand tried again, but it still fails. Do you mean hdparm should not touch the device at all and a reboot without the hdparm -d 1/dev/hdawould do the job? I could live with that for the moment, as I don't have to repartition my drive very often...
Exactly. At least that's what I'm seeing here.
Signature · 8 lines
=====================================================================
Mohammad A. Haque http://www.haque.net/
[email protected]
"Alcohol and calculus don't mix. Developer/Project Lead
Don't drink and derive." --Unknown http://wm.themes.org/
[email protected]
=====================================================================Quoted 6 lines · Tim Tassonis
Well I do use hdparm -d 1
/dev/hdain init to set dma to 1. I know called hdparm -d 0/dev/hdaand tried again, but it still fails. Do you mean hdparm should not touch the device at all and a reboot without the hdparm -d 1/dev/hdawould do the job? I could live with that for the moment, as I don't have to repartition my drive very often...
Woops. hit send too fast.
You can use hdparm once you've repartitioned though it seems. Still won't be able create any files >2GB once you've touched it with hdparm again but at least you'll be up and running with whatever size partitions you want and have dma enabled. Dunno if that's an issue.
Signature · 8 lines
=====================================================================
Mohammad A. Haque http://www.haque.net/
[email protected]
"Alcohol and calculus don't mix. Developer/Project Lead
Don't drink and derive." --Unknown http://wm.themes.org/
[email protected]
=====================================================================Quoted 3 lines · On Wed, 24 Oct 2001 12:42:27 -0400 (EDT) "Mohammad A. Haque"…
Quoted 1 line · Tim Tassonis
Well I do use hdparm -d 1
/dev/hdain init to set dma to 1. I know
called
Quoted 2 lines
Quoted 2 lines
hdparm -d 0
/dev/hdaand tried again, but it still fails. Do you mean hdparm should not touch the device at all and a reboot without the
hdparm
Quoted 1 line
Quoted 1 line
-d 1
/dev/hdawould do the job? I could live with that for the moment,
as
Quoted 9 lines
Quoted 2 lines
I don't have to repartition my drive very often...
Woops. hit send too fast.
You can use hdparm once you've repartitioned though it seems. Still won't be able create any files >2GB once you've touched it with hdparm again but at least you'll be up and running with whatever size partitions you want and have dma enabled. Dunno if that's an issue.
I'm quite suprised, but this actually worked for me. Rebooted without using hdparm, created the partintion (3GB) and everything seems ok. Looks as if hdparm is doing something wrong here (v3.6).
Bye
Tim
Quoted 4 lines · Tim Tassonis
I'm quite suprised, but this actually worked for me. Rebooted without using hdparm, created the partintion (3GB) and everything seems ok. Looks as if hdparm is doing something wrong here (v3.6).
More than likely it's just triggering something that causes the problem.
Signature · 8 lines
=====================================================================
Mohammad A. Haque http://www.haque.net/
[email protected]
"Alcohol and calculus don't mix. Developer/Project Lead
Don't drink and derive." --Unknown http://wm.themes.org/
[email protected]
=====================================================================In article <[email protected]>, Mohammad A. Haque <[email protected]> wrote:
| On Thu, 25 Oct 2001, Tim Tassonis wrote: | | > I'm quite suprised, but this actually worked for me. Rebooted without | > using hdparm, created the partintion (3GB) and everything seems ok. Looks | > as if hdparm is doing something wrong here (v3.6). | > | | More than likely it's just triggering something that causes the problem.
I haven't seen any problem, either. Certainly not with fdisk, this is what I see:
================================================================
bilbo:root> hdparm -V
hdparm v3.9
bilbo:root> df
Filesystem 1k-blocks Used Available Use% Mounted on
/dev/hda3 995896 849248 95240 90% / /dev/hda4 4597818 2727382 1639502 62% /extra /extra/u_local 193687 74214 109473 40% /usr/local /dev/hde1 4079656 3611952 262908 93% /extra2
bilbo:root> fdisk /dev/hde
The number of cylinders for this disk is set to 39770. There is nothing wrong with that, but this is larger than 1024, and could in certain setups cause problems with:
1) software that runs at boot time (e.g., old versions of LILO)
2) booting and partitioning software from other OSs (e.g., DOS FDISK, OS/2 FDISK)
Command (m for help): p
Disk /dev/hde: 16 heads, 63 sectors, 39770 cylinders Units = cylinders of 1008 * 512 bytes
Device Boot Start End Blocks Id System /dev/hde1 1 8127 4095976+ 83 Linux native /dev/hde2 8128 28445 10240272 83 Linux native
Command (m for help): q
================================================================
I certainly have used hdparm on that drive, my controller comes up in ATA33 by default, and I run
# enable the ATA/66 hard drive(s) # experiment with -u1 after backup hdparm -d1 -X66 /dev/hde out of rc.local to get it going. BP6 m/b, dual Celeron500, Linux bilbo 2.4.10-ac7-2 #5 SMP Sun Oct 7 08:03:37 EDT 2001 i686 unknown from the uname. This is NOT a preempt kernel, the patch against this one blew up on SMP, although it booted "nosmp" just fine. I have trying again with 2.4.13-pre6 this weekend.
Don't know if this sheds light on the topic, I certainly do run fdisk on "drives" my RAID controller creates which have 600GB or so broken into little 100GB files.
Signature · 3 lines
bill davidsen <[email protected]> His first management concern is not solving the problem, but covering his ass. If he lived in the middle ages he'd wear his codpiece backward.
Quoted 6 lines · bill davidsen
I haven't seen any problem, either. Certainly not with fdisk, this is what I see:
================================================================
bilbo:root> hdparm -V
hdparm v3.9
Quoted 6 lines
bilbo:root> df
....Don't know if this sheds light on the topic, I certainly do run fdisk on "drives" my RAID controller creates which have 600GB or so broken into little 100GB files.
I guess it was unclear at first. You'll only get the error when you run mke2fs.
Signature · 8 lines
=====================================================================
Mohammad A. Haque http://www.haque.net/
[email protected]
"Alcohol and calculus don't mix. Developer/Project Lead
Don't drink and derive." --Unknown http://wm.themes.org/
[email protected]
=====================================================================Quoted 11 lines · Mohammad A. Haque
Quoted 9 lines · bill davidsen
I haven't seen any problem, either. Certainly not with fdisk, this is what I see:
================================================================
bilbo:root> hdparm -V
hdparm v3.9bilbo:root> df
....
Quoted 6 lines
Quoted 3 lines
Don't know if this sheds light on the topic, I certainly do run fdisk on "drives" my RAID controller creates which have 600GB or so broken into little 100GB files.
I guess it was unclear at first. You'll only get the error when you run mke2fs.
I still am missing this, obviously after I partition the drive I do mke2fs so I can use the partition. I don't see what sequence you follow which triggers this, can you clarify?
Signature · 3 lines
bill davidsen <[email protected]> CTO, TMR Associates, Inc Doing interesting things with little computers since 1979.
Quoted 3 lines · Bill Davidsen
I still am missing this, obviously after I partition the drive I do mke2fs so I can use the partition. I don't see what sequence you follow which triggers this, can you clarify?
I thought i already sent you (maybe it was to someone else in private email) the steps/cases that succeed/fail. I'll dig up the email if not.
What version of glibc are you compiled against? I've got 2.1.3. it could also be controller specific. I tried it on a HPT366. Haven't tried it on my onboard (440bx motherboard).
I've only seen one confirmation on the list that duplicates what I'm seeing.
More info later.
Signature · 8 lines
=====================================================================
Mohammad A. Haque http://www.haque.net/
[email protected]
"Alcohol and calculus don't mix. Developer/Project Lead
Don't drink and derive." --Unknown http://www.themes.org/
[email protected]
=====================================================================Quoted 9 lines
Quoted 6 lines
Quoted 3 lines
The latter seems to be the case because Vita Samel (hope I got this right) just reported that "Booting into 2.4.10-ac10" fixed the problem. Perhaps it once was fixed and later defixed?
Sounds like it. I'll have a look some point next week to see if I can see what is up
I'm able fdisk/mke2fs with 2.4.13-pre6 without the error so long as I don't touch the device with hdparm.
I have SCSI only system. My problems were with mke2fs >2GiB, but no
problems with fdisk (tried to fdisk/mke2fs my shiny new 40GiB Seagate SCSI disk).
Vita Samel
Hi!
This is MeToo(tm) message. Limits set to unlimited, glibc-2.2.2 compiled
against 2.4.0 headers.
Booting into 2.4.10-ac10 kernel problem "solved".
Quoted 7 lines
When I try to create a partition of 2GB using fdisk or parted, I get the error "File size limit exceeded (core dumped)". I already read about this error on the mailing list, but sadly not of any solution.
Has anybody got one?
Btw: If happend with fdisk from util-linux-2.10f until util-linux-2.11l.
Looking forward to proper fix.
Cheers,
Vita
Works here, I just created a 130GB partition using 2.4.12. glibc-2.2.4 running on debian.
Gerhard
Quoted 16 lines · Vitezslav Samel
Hi!This is MeToo(tm) message. Limits set to unlimited, glibc-2.2.2 compiled
against 2.4.0 headers.
Booting into 2.4.10-ac10 kernel problem "solved".Quoted 7 lines
When I try to create a partition of 2GB using fdisk or parted, I get the error "File size limit exceeded (core dumped)". I already read about this error on the mailing list, but sadly not of any solution.
Has anybody got one?
Btw: If happend with fdisk from util-linux-2.10f until util-linux-2.11l.
Looking forward to proper fix.
Quoted 8 lines
Cheers,
Vita
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
--
Gerhard Mack
<>< As a computer I find your faith in technology amusing.