Skip to contentSkip to conversation

rawmidi problems

DISCUSSION Pedro Lopez-Cabanillas 3 participants 8 messages Jul 5, 2002 – Jul 8, 2002

lore
Share & tools
lore
#0 lore raw

Hi,

I was trying to test rawmidi on snd-usb-midi with latest patches, with no success :(

Then, as I have an sb 128 (snd-ens1371) I tryed the alsa-lib/test/rawmidi program with only that card module loaded.

$ ./rawmidi -i hw:0,0
Read midi in
Press ctrl-c to stop
(With a MIDI keyboard connected, no events received at all.)
$ ./rawmidi -i hw:0,0 -o hw:0,0 -t
(OK, input events sent to out, with a lot of delay)
$ ./rawmidi -o hw:0,0
Writing note on / note off
(OK)

With alsa-lib/test/seq program all tests OK.

Regards,
Pedro

-------------------------------------------------------
This sf.net email is sponsored by:ThinkGeek
Bringing you mounds of caffeinated joy.
http://thinkgeek.com/sf

#1 lore raw

add the flag -v to get verbose output and see what events you receive (this should be default behaviour i guess...)

-------------------------------------------------------
This sf.net email is sponsored by:ThinkGeek
Bringing you mounds of caffeinated joy.
http://thinkgeek.com/sf

#2 lore raw
Quoted 2 lines · Maarten de Boer

add the flag -v to get verbose output and see what events you receive (this should be default behaviour i guess...)

It works! (and also with snd-usb-midi)
And I agree with you, -v option should be the default :)

$ ./rawmidi  -i hw:0,0 -v
Using:
Input: device hw:0,0
Output: NONE
Read midi in
Press ctrl-c to stop
read fe
read fe
read fe
read fe
read fe
read fe
read fe
read fe
read fe
Closing

Thanks,
Pedro

-------------------------------------------------------
This sf.net email is sponsored by:ThinkGeek
Bringing you mounds of caffeinated joy.
http://thinkgeek.com/sf

#3 lore raw
In reply to Pedro Lopez-Cabanillas

At Fri, 5 Jul 2002 17:53:54 +0200,

Quoted 8 lines · Pedro Lopez-Cabanillas

Hi,

I was trying to test rawmidi on snd-usb-midi with latest patches, with no success :(

Then, as I have an sb 128 (snd-ens1371) I tryed the alsa-lib/test/rawmidi program with only that card module loaded.

there might be still bugs on virmidi codes.
i remember that it didn't work quite well on some conditions...

will check later.

ciao,

Takashi

-------------------------------------------------------
This sf.net email is sponsored by:ThinkGeek
Bringing you mounds of caffeinated joy.
http://thinkgeek.com/sf

#4 lore raw
Quoted 10 lines · Takashi Iwai
Quoted 5 lines

I was trying to test rawmidi on snd-usb-midi with latest patches, with no success :(

Then, as I have an sb 128 (snd-ens1371) I tryed the alsa-lib/test/rawmidi program with only that card module loaded.

there might be still bugs on virmidi codes.
i remember that it didn't work quite well on some conditions...

will check later.

It works, sorry. I forgave the -v flag on rawmidi program :) Thanks everybody.

Now I am trying to test the oss midi emulation. MIDI Output works, but no input at all. I'm trying:

$ cat /dev/midi00 | od -x
(nothing happens, nor with /dev/snd/midiC0D0)
$ ls -l /dev/midi*
lrwxrwxrwx    1 root     audio          10 dic  4  2001 /dev/midi -> 
/dev/midi0
crw-------    1 plc      audio     14,   2 dic  4  2001 /dev/midi0
crw-------    1 plc      audio     14,   2 ago 30  2001 /dev/midi00
crw-------    1 plc      audio     14,  18 ago 30  2001 /dev/midi01
crw-------    1 plc      audio     14,  34 ago 30  2001 /dev/midi02
crw-------    1 plc      audio     14,  50 ago 30  2001 /dev/midi03
crw-------    1 plc      audio     14,  66 abr 18 20:17 /dev/midi04

Another question: I have a snd-ens1371 and two snd-usb-midi: a Roland/Edirol UM-2 and a Midiman Midisport 2x2. These are my modules.conf settings:

alias char-major-116 snd
alias char-major-14 soundcore
options snd snd_major=116 snd_cards_limit=3
alias snd-card-0 snd-ens1371
alias sound-slot-0 snd-card-0
alias sound-service-0-0 snd-mixer-oss
alias sound-service-0-1 snd-seq-oss
alias sound-service-0-3 snd-pcm-oss
alias sound-service-0-8 snd-seq-oss
alias sound-service-0-12 snd-pcm-oss
# ------------- USB MIDI ------------
alias snd-card-1 snd-usb-midi
alias sound-slot-1 snd-card-1
alias sound-service-1-1 snd-seq-oss
alias sound-service-1-8 snd-seq-oss
alias snd-card-2 snd-usb-midi
alias sound-slot-2 snd-card-2
alias sound-service-2-1 snd-seq-oss
alias sound-service-2-8 snd-seq-oss

with /dev/midi00 ouput goes to ens-1371, /dev/midi01 goes to the first usb midi device, and /dev/midi02 goes to the second, but both usb devices have 2 inputs ans 2 outputs. Can I get all my five midi ports work with oss midi emulation?

Thanks,
Pedro

-------------------------------------------------------
This sf.net email is sponsored by:ThinkGeek
Bringing you mounds of caffeinated joy.
http://thinkgeek.com/sf

#5 lore raw

At Fri, 5 Jul 2002 19:30:42 +0200,

Quoted 24 lines · Pedro Lopez-Cabanillas

Another question: I have a snd-ens1371 and two snd-usb-midi: a Roland/Edirol UM-2 and a Midiman Midisport 2x2. These are my modules.conf settings:

alias char-major-116 snd
alias char-major-14 soundcore
options snd snd_major=116 snd_cards_limit=3
alias snd-card-0 snd-ens1371
alias sound-slot-0 snd-card-0
alias sound-service-0-0 snd-mixer-oss
alias sound-service-0-1 snd-seq-oss
alias sound-service-0-3 snd-pcm-oss
alias sound-service-0-8 snd-seq-oss
alias sound-service-0-12 snd-pcm-oss
# ------------- USB MIDI ------------
alias snd-card-1 snd-usb-midi
alias sound-slot-1 snd-card-1
alias sound-service-1-1 snd-seq-oss
alias sound-service-1-8 snd-seq-oss
alias snd-card-2 snd-usb-midi
alias sound-slot-2 snd-card-2
alias sound-service-2-1 snd-seq-oss
alias sound-service-2-8 snd-seq-oss

Quoted 4 lines

with /dev/midi00 ouput goes to ens-1371, /dev/midi01 goes to the first usb midi device, and /dev/midi02 goes to the second, but both usb devices have 2 inputs ans 2 outputs. Can I get all my five midi ports work with oss midi emulation?

do you really need to use oss midi devices?
as long as you only reading/writing midi byte streams (i.e. no ioctls), you can use simply alsa rawmidi devices, /dev/snd/midiCxDx, instead of /dev/midiXX.

Takashi

-------------------------------------------------------
This sf.net email is sponsored by:ThinkGeek
Oh, it's good to be a geek.
http://thinkgeek.com/sf

#6 lore raw
Quoted 11 lines · Takashi Iwai

At Fri, 5 Jul 2002 19:30:42 +0200,

Quoted 4 lines · Pedro Lopez-Cabanillas

with /dev/midi00 ouput goes to ens-1371, /dev/midi01 goes to the first usb midi device, and /dev/midi02 goes to the second, but both usb devices have 2 inputs ans 2 outputs. Can I get all my five midi ports work with oss midi emulation?

do you really need to use oss midi devices?
as long as you only reading/writing midi byte streams (i.e. no ioctls), you can use simply alsa rawmidi devices, /dev/snd/midiCxDx, instead of /dev/midiXX.

No, I agree with you. In fact, I don't need the raw midi devices at all, as the sequencer API can do all and more.

My question was if I made a mistake or I am forgiving something, or if it is a limitation on ALSA OSS emulation. Only trying to deeply test the new snd-usb-midi driver. And for the fun of doing the things in several different ways.

As an example, and only for fun, this is a bash script for cron (hourly, of course) that plays thru raw midi devices without any special program.

Best regards,
Pedro

#!/bin/bash
#
# London Tower Big Ben tune as a simple bash script
# Copyright (C) 2002 Pedro Lopez-Cabanillas
#
# This program is free software; you can redistribute it and/or modify

# it under the terms of the GNU General Public License as published by
# the Free Software Foundation; either version 2 of the License, or
# (at your option) any later version.
#
# This program is distributed in the hope that it will be useful,
# but WITHOUT ANY WARRANTY; without even the implied warranty of
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
# GNU General Public License for more details.
#
# You should have received a copy of the GNU General Public License
# along with this program; if not, write to the Free Software
# Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
#
tune="C 4, E 4, D 4, g 2, C 4, D 4, E 4, C 2, \
      E 4, C 4, D 4, g 2, g 4, D 4, E 4, C 2,"

mididev="/dev/midi03"
tempo=80 # quarters per minute

function playnote() {
	let "ms = 240000 / ($2 * $tempo)"
	echo -ne '\x90' >&3
	echo -ne "$1\144" >&3
	sleep $ms'e-3s'
	echo -ne '\x80' >&3
	echo -ne "$1\000" >&3
}

function playtune() {
echo $1 | tr "cdefgabCDEFGAB" "<>@ACEGHJLMOQS" | \
while read -rd, note length; do
playnote $note $length
done
}

function playhour() {
	h=`date +%l`
	while [ $h -gt 0 ]; do
	    playnote $'\x37' 2
	    let "h--"
	done
}

if [ -c $mididev -a -w $mididev ]; then

	exec 3>$mididev
	echo -ne '\xb0\x07\x7f' >&3	# volume = 127
	echo -ne '\xc0\x0e' >&3		# instrument = bells
	playtune "$tune"
	sleep 2
	playhour
	exec 3<&-

else
echo "basename $0 : invalid MIDI device ( $mididev )"
fi

-------------------------------------------------------
This sf.net email is sponsored by:ThinkGeek
Oh, it's good to be a geek.
http://thinkgeek.com/sf

#7 lore raw

At Mon, 8 Jul 2002 17:41:46 +0200,

Quoted 14 lines · Pedro Lopez-Cabanillas
Quoted 11 lines · Takashi Iwai

At Fri, 5 Jul 2002 19:30:42 +0200,

Quoted 4 lines · Pedro Lopez-Cabanillas

with /dev/midi00 ouput goes to ens-1371, /dev/midi01 goes to the first usb midi device, and /dev/midi02 goes to the second, but both usb devices have 2 inputs ans 2 outputs. Can I get all my five midi ports work with oss midi emulation?

do you really need to use oss midi devices?
as long as you only reading/writing midi byte streams (i.e. no ioctls), you can use simply alsa rawmidi devices, /dev/snd/midiCxDx, instead of /dev/midiXX.

Quoted 7 lines

No, I agree with you. In fact, I don't need the raw midi devices at all, as the sequencer API can do all and more.

My question was if I made a mistake or I am forgiving something, or if it is a limitation on ALSA OSS emulation. Only trying to deeply test the new snd-usb-midi driver. And for the fun of doing the things in several different ways.

ok, point taken.

on OSS emulation, only up to two devices can be assigned per card. one is assigned to /dev/midiXX and another to /dev/amidiXX. which device is mapped can be changed via snd_midi_map and snd_amidi_map options for snd-rawmidi module.
as default, they are specified as 0 and 1, respectively.

Quoted 2 lines

As an example, and only for fun, this is a bash script for cron (hourly, of course) that plays thru raw midi devices without any special program.

cool :)

ciao,

Takashi

-------------------------------------------------------
This sf.net email is sponsored by:ThinkGeek
Oh, it's good to be a geek.
http://thinkgeek.com/sf