Skip to contentSkip to conversation

block/xd: replace schedule_timeout() with msleep()/msleep_interruptible()

PATCH In review [email protected] 1 participant 1 message Nov 20, 2004 Block layer

lore
Share & tools
lore

[email protected]

author
#0 lore raw

PATCH 4/10 block/xd: replace schedule_timeout() with msleep()/msleep_interruptible()

Any comments would be appreciated.

Description: Use msleep() or msleep_interruptible() [as appropriate] instead of schedule_timeout() to gurantee the task delays as expected. As a result changed the units of the timeout variable from jiffies to msecs.

Signed-off-by Nishanth Aravamudan <[email protected]>
Signed-off-by Maximilian Attems <[email protected]>

---

 linux-2.6.10-rc2-bk4-max/drivers/block/xd.c |   14 +++++---------
 1 files changed, 5 insertions(+), 9 deletions(-)
drivers/block/xd.c renamed from drivers/block/xd.c~msleep-drivers_block_xd +5 -9
diff -puN drivers/block/xd.c~msleep-drivers_block_xd drivers/block/xd.c
@@ -62,7 +62,7 @@ static int xd[5] = { -1,-1,-1,-1, };
 
 #define XD_DONT_USE_DMA		0  /* Initial value. may be overriden using
 				      "nodma" module option */
-#define XD_INIT_DISK_DELAY	(30*HZ/1000)  /* 30 ms delay during disk initialization */
+#define XD_INIT_DISK_DELAY	(30)  /* 30 ms delay during disk initialization */
 
 /* Above may need to be increased if a problem with the 2nd drive detection
    (ST11M controller) or resetting a controller (WD) appears */

@@ -625,14 +625,12 @@ static u_char __init xd_initdrives (void
 	for (i = 0; i < XD_MAXDRIVES; i++) {
 		xd_build(cmdblk,CMD_TESTREADY,i,0,0,0,0,0);
 		if (!xd_command(cmdblk,PIO_MODE,NULL,NULL,NULL,XD_TIMEOUT*8)) {
-			set_current_state(TASK_INTERRUPTIBLE);
-			schedule_timeout(XD_INIT_DISK_DELAY);
+			msleep_interruptible(XD_INIT_DISK_DELAY);
 
 			init_drive(count);
 			count++;
 
-			set_current_state(TASK_INTERRUPTIBLE);
-			schedule_timeout(XD_INIT_DISK_DELAY);
+			msleep_interruptible(XD_INIT_DISK_DELAY);
 		}
 	}
 	return (count);

@@ -753,8 +751,7 @@ static void __init xd_wd_init_controller
 
 	outb(0,XD_RESET);		/* reset the controller */
 
-	set_current_state(TASK_UNINTERRUPTIBLE);
-	schedule_timeout(XD_INIT_DISK_DELAY);
+	msleep(XD_INIT_DISK_DELAY);
 }
 
 static void __init xd_wd_init_drive (u_char drive)

@@ -928,8 +925,7 @@ If you need non-standard settings use th
 	xd_maxsectors = 0x01;
 	outb(0,XD_RESET);		/* reset the controller */
 
-	set_current_state(TASK_UNINTERRUPTIBLE);
-	schedule_timeout(XD_INIT_DISK_DELAY);
+	msleep(XD_INIT_DISK_DELAY);
 }
 
 static void __init xd_xebec_init_drive (u_char drive)

_