Skip to contentSkip to conversation

net: marvell: mvpp2: use mvpp2_is_xlg() helper elsewhere

PATCH Applied Russell King 3 participants 3 messages Feb 11, 2019 – Feb 12, 2019

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH 2/2 net: marvell: mvpp2: use mvpp2_is_xlg() helper elsewhere

There are several places which make the decision whether to access the XLGMAC vs GMAC that only check for PHY_INTERFACE_MODE_10GKR and not its XAUI variant. Switch these to use the new helper so that we have consistency through the driver.

---
 drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 15 ++++++---------
 1 file changed, 6 insertions(+), 9 deletions(-)
drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c +6 -9
index 03c79618bfef..94c92a49f12f 100644
@@ -1106,7 +1106,7 @@ static void mvpp22_gop_unmask_irq(struct mvpp2_port *port)
 	if (port->gop_id == 0) {
 		/* Enable the XLG/GIG irqs for this port */
 		val = readl(port->base + MVPP22_XLG_EXT_INT_MASK);
-		if (port->phy_interface == PHY_INTERFACE_MODE_10GKR)
+		if (mvpp2_is_xlg(port->phy_interface))
 			val |= MVPP22_XLG_EXT_INT_MASK_XLG;
 		else
 			val |= MVPP22_XLG_EXT_INT_MASK_GIG;
@@ -2471,8 +2471,7 @@ static irqreturn_t mvpp2_link_status_isr(int irq, void *dev_id)
 
 	mvpp22_gop_mask_irq(port);
 
-	if (port->gop_id == 0 &&
-	    port->phy_interface == PHY_INTERFACE_MODE_10GKR) {
+	if (port->gop_id == 0 && mvpp2_is_xlg(port->phy_interface)) {
 		val = readl(port->base + MVPP22_XLG_INT_STAT);
 		if (val & MVPP22_XLG_INT_STAT_LINK) {
 			event = true;
@@ -4680,7 +4679,7 @@ static void mvpp2_mac_config(struct net_device *dev, unsigned int mode,
 	bool change_interface = port->phy_interface != state->interface;
 
 	/* Check for invalid configuration */
-	if (state->interface == PHY_INTERFACE_MODE_10GKR && port->gop_id != 0) {
+	if (mvpp2_is_xlg(state->interface) && port->gop_id != 0) {
 		netdev_err(dev, "Invalid mode on %s\n", dev->name);
 		return;
 	}
@@ -4700,7 +4699,7 @@ static void mvpp2_mac_config(struct net_device *dev, unsigned int mode,
 	}
 
 	/* mac (re)configuration */
-	if (state->interface == PHY_INTERFACE_MODE_10GKR)
+	if (mvpp2_is_xlg(state->interface))
 		mvpp2_xlg_config(port, mode, state);
 	else if (phy_interface_mode_is_rgmii(state->interface) ||
 		 phy_interface_mode_is_8023z(state->interface) ||
@@ -4722,8 +4721,7 @@ static void mvpp2_mac_link_up(struct net_device *dev, unsigned int mode,
 	struct mvpp2_port *port = netdev_priv(dev);
 	u32 val;
 
-	if (!phylink_autoneg_inband(mode) &&
-	    interface != PHY_INTERFACE_MODE_10GKR) {
+	if (!phylink_autoneg_inband(mode) && !mvpp2_is_xlg(interface)) {
 		val = readl(port->base + MVPP2_GMAC_AUTONEG_CONFIG);
 		val &= ~MVPP2_GMAC_FORCE_LINK_DOWN;
 		val |= MVPP2_GMAC_FORCE_LINK_PASS;
@@ -4743,8 +4741,7 @@ static void mvpp2_mac_link_down(struct net_device *dev, unsigned int mode,
 	struct mvpp2_port *port = netdev_priv(dev);
 	u32 val;
 
-	if (!phylink_autoneg_inband(mode) &&
-	    interface != PHY_INTERFACE_MODE_10GKR) {
+	if (!phylink_autoneg_inband(mode) && !mvpp2_is_xlg(interface)) {
 		val = readl(port->base + MVPP2_GMAC_AUTONEG_CONFIG);
 		val &= ~MVPP2_GMAC_FORCE_LINK_PASS;
 		val |= MVPP2_GMAC_FORCE_LINK_DOWN;
Signature · 1 line
2.7.4
Reviewed-by on v1 2/2
#1 lore raw

Hello Russell,

Quoted 6 lines · On Mon, 11 Feb 2019 10:23:15 +0000 Russell King <[email protected]>…

There are several places which make the decision whether to access the XLGMAC vs GMAC that only check for PHY_INTERFACE_MODE_10GKR and not its XAUI variant. Switch these to use the new helper so that we have consistency through the driver.

Thanks,

Maxime