Convert sa1100 serial to use mctrl gpios
Subsystems (3)
Russell King - ARM Linux admin
maintainercover Convert sa1100 serial to use mctrl gpios
This series takes the next step along the path of cleaning up and modernising the sa11x0 code, concentrating on the sa1100 serial driver. At the end of this conversion, we are left with collie being the only platform that uses the old platform data get_mctrl and set_mctrl methods. As the locomo code is also used with PXA, this is left for a future cleanup.
The first patch was previously acked quite some time ago.
I'm intending to send this to arm-soc.
arch/arm/mach-sa1100/assabet.c | 91 +++++++++++---------------------- arch/arm/mach-sa1100/badge4.c | 2 - arch/arm/mach-sa1100/h3xxx.c | 64 ++++------------------- arch/arm/mach-sa1100/hackkit.c | 48 ------------------ arch/arm/mach-sa1100/neponset.c | 109 +++++++++++----------------------------- drivers/tty/serial/Kconfig | 1 + drivers/tty/serial/sa1100.c | 42 ++++++++++++++-- 7 files changed, 106 insertions(+), 251 deletions(-)
Signature · 3 lines
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/ FTTC broadband for 0.8mile line in suburbia: sync at 12.1Mbps down 622kbps up According to speedtest.net: 11.9Mbps down 500kbps up
PATCH 1/6 serial: sa1100: add support for mctrl gpios
Add support for the generic mctrl gpio helper. This will allow us to convert several board files to use the gpiod tables to assign GPIOs to serial ports, rather than needing to have private function callbacks.
If the generic mctrl gpio helper fails, ignore the mctrl gpios rather than preventing the (possibly console) serial port from being created.
--- drivers/tty/serial/Kconfig | 1 + drivers/tty/serial/sa1100.c | 42 ++++++++++++++++++++++++++++++++++++++---- 2 files changed, 39 insertions(+), 4 deletions(-)
drivers/tty/serial/Kconfig +1 -0
@@ -511,6 +511,7 @@ config SERIAL_SA1100 bool "SA1100 serial port support" depends on ARCH_SA1100 select SERIAL_CORE + select SERIAL_MCTRL_GPIO if GPIOLIB help If you have a machine based on a SA1100/SA1110 StrongARM(R) CPU you can enable its onboard serial port by enabling this option.
drivers/tty/serial/sa1100.c +38 -4
82 lines not on this page · raw message
Signature · 1 line
2.7.4
Re: [PATCH 1/6] serial: sa1100: add support for mctrl gpios
Quoted 81 lines · Russell King
Add support for the generic mctrl gpio helper. This will allow us to convert several board files to use the gpiod tables to assign GPIOs to serial ports, rather than needing to have private function callbacks.
If the generic mctrl gpio helper fails, ignore the mctrl gpios rather than preventing the (possibly console) serial port from being created.
Acked-by Linus Walleij <[email protected]>Signed-off-by Russell King <[email protected]>--- drivers/tty/serial/Kconfig | 1 + drivers/tty/serial/sa1100.c | 42 ++++++++++++++++++++++++++++++++++++++---- 2 files changed, 39 insertions(+), 4 deletions(-)drivers/tty/serial/Kconfig +1
-0@@ -511,6 +511,7 @@ config SERIAL_SA1100 bool "SA1100 serial port support" depends on ARCH_SA1100 select SERIAL_CORE + select SERIAL_MCTRL_GPIO if GPIOLIB help If you have a machine based on a SA1100/SA1110 StrongARM(R) CPU you can enable its onboard serial port by enabling this option.drivers/tty/serial/sa1100.c +16
-1@@ -28,6 +28,8 @@#include <mach/hardware.h> #include <mach/irqs.h> +#include "serial_mctrl_gpio.h" +/* We've been assigned a range on the "Low-density serial ports" major */ #define SERIAL_SA1100_MAJOR 204#define MINOR_START 5@@ -77,6 +79,7 @@ struct sa1100_port {struct uart_port port;struct timer_list timer;unsigned int old_status; +struct mctrl_gpios *gpios; };/* @@ -174,6 +177,8 @@ static void sa1100_enable_ms(struct uart_port *port) container_of(port, struct sa1100_port, port);mod_timer (&sport->timer, jiffies); + +mctrl_gpio_enable_ms (sport->gpios); } static void@@ -322,11 +327,21 @@ static unsigned int sa1100_tx_empty(struct uart_port *port)static unsigned int sa1100_get_mctrl (struct uart_port *port) { -return TIOCM_CTS |TIOCM_DSR |TIOCM_CAR ; +struct sa1100_port *sport = + container_of(port, struct sa1100_port, port); +int ret =TIOCM_CTS |TIOCM_DSR |TIOCM_CAR ; + +mctrl_gpio_get (sport->gpios, &ret); + +return ret; }static void sa1100_set_mctrl (struct uart_port *port,unsigned int mctrl) { +struct sa1100_port *sport = + container_of(port, struct sa1100_port, port); + +mctrl_gpio_set (sport->gpios, mctrl); }/*
drivers/tty/serial/sa1100.c static int sa1100_serial_resume(struct platform_device *dev) · line 863
Quoted 7 lines
drivers/tty/serial/sa1100.c +4
-0@@ -842,6 +857,27 @@ static int sa1100_serial_resume(struct platform_device *dev)return 0 ; } +static int sa1100_serial_add_one_port (struct sa1100_port *sport,struct platform_device *dev) +{ + sport->port.dev = &dev->dev; + sport->gpios =mctrl_gpio_init_noauto (sport->port.dev,0 );
the _noauto function was only introduced to ease a transition. I think the driver would benefit to use mctrl_gpio_init() instead.
Getting rid of mctrl_gpio_init_noauto() was on my todo list for some time, but it was pushed down too far :-|
Best regards
Uwe
Signature · 2 lines
Pengutronix e.K. | Uwe Kleine-König | Industrial Linux Solutions | http://www.pengutronix.de/ |
Russell King - ARM Linux admin
maintainerRe: [PATCH 1/6] serial: sa1100: add support for mctrl gpios
Quoted 85 lines · Uwe Kleine-König
Quoted 84 lines · Russell King
Add support for the generic mctrl gpio helper. This will allow us to convert several board files to use the gpiod tables to assign GPIOs to serial ports, rather than needing to have private function callbacks.
If the generic mctrl gpio helper fails, ignore the mctrl gpios rather than preventing the (possibly console) serial port from being created.
Acked-by Linus Walleij <[email protected]>Signed-off-by Russell King <[email protected]>--- drivers/tty/serial/Kconfig | 1 + drivers/tty/serial/sa1100.c | 42 ++++++++++++++++++++++++++++++++++++++---- 2 files changed, 39 insertions(+), 4 deletions(-)drivers/tty/serial/Kconfig +1
-0@@ -511,6 +511,7 @@ config SERIAL_SA1100 bool "SA1100 serial port support" depends on ARCH_SA1100 select SERIAL_CORE + select SERIAL_MCTRL_GPIO if GPIOLIB help If you have a machine based on a SA1100/SA1110 StrongARM(R) CPU you can enable its onboard serial port by enabling this option.drivers/tty/serial/sa1100.c +16
-1@@ -28,6 +28,8 @@#include <mach/hardware.h> #include <mach/irqs.h> +#include "serial_mctrl_gpio.h" +/* We've been assigned a range on the "Low-density serial ports" major */ #define SERIAL_SA1100_MAJOR 204#define MINOR_START 5@@ -77,6 +79,7 @@ struct sa1100_port {struct uart_port port;struct timer_list timer;unsigned int old_status; +struct mctrl_gpios *gpios; };/* @@ -174,6 +177,8 @@ static void sa1100_enable_ms(struct uart_port *port) container_of(port, struct sa1100_port, port);mod_timer (&sport->timer, jiffies); + +mctrl_gpio_enable_ms (sport->gpios); } static void@@ -322,11 +327,21 @@ static unsigned int sa1100_tx_empty(struct uart_port *port)static unsigned int sa1100_get_mctrl (struct uart_port *port) { -return TIOCM_CTS |TIOCM_DSR |TIOCM_CAR ; +struct sa1100_port *sport = + container_of(port, struct sa1100_port, port); +int ret =TIOCM_CTS |TIOCM_DSR |TIOCM_CAR ; + +mctrl_gpio_get (sport->gpios, &ret); + +return ret; }static void sa1100_set_mctrl (struct uart_port *port,unsigned int mctrl) { +struct sa1100_port *sport = + container_of(port, struct sa1100_port, port); + +mctrl_gpio_set (sport->gpios, mctrl); }/* @@ -842,6 +857,27 @@ static int sa1100_serial_resume(struct platform_device *dev)return 0 ; }
Quoted 7 lines
drivers/tty/serial/sa1100.c static int sa1100_serial_resume(struct platform_device *dev) · line 863
Quoted 4 lines
drivers/tty/serial/sa1100.c +4
-0+static int sa1100_serial_add_one_port (struct sa1100_port *sport,struct platform_device *dev) +{ + sport->port.dev = &dev->dev; + sport->gpios =mctrl_gpio_init_noauto (sport->port.dev,0 );the
_noautofunction was only introduced to ease a transition. I think the driver would benefit to usemctrl_gpio_init()instead.
In what way would the driver benefit? mctrl_gpio_init() requires that there are IRQs for each input GPIO. This is not the case with most SA11x0 platforms, where the GPIO controls are implemented using simple latches, hence that interface is entirely unsuitable.
Signature · 3 lines
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/ FTTC broadband for 0.8mile line in suburbia: sync at 12.1Mbps down 622kbps up According to speedtest.net: 11.9Mbps down 500kbps up
Re: [PATCH 1/6] serial: sa1100: add support for mctrl gpios
Quoted 10 lines · Russell King - ARM Linux admin
Quoted 8 lines · Uwe Kleine-König
drivers/tty/serial/sa1100.c static int sa1100_serial_resume(struct platform_device *dev) · line 863
Quoted 4 lines · Russell King
drivers/tty/serial/sa1100.c +4
-0+static int sa1100_serial_add_one_port (struct sa1100_port *sport,struct platform_device *dev) +{ + sport->port.dev = &dev->dev; + sport->gpios =mctrl_gpio_init_noauto (sport->port.dev,0 );the
_noautofunction was only introduced to ease a transition. I think the driver would benefit to usemctrl_gpio_init()instead.
Quoted 4 lines
In what way would the driver benefit?
mctrl_gpio_init()requires that there are IRQs for each input GPIO. This is not the case with most SA11x0 platforms, where the GPIO controls are implemented using simple latches, hence that interface is entirely unsuitable.
Ah, but then you can only use the outputs reliably here as an edge on (say) CTS stays unnoticed with both mctrl_gpio_init() and mctrl_gpio_init_noauto().
Unless I miss something (which is quite possible given that it's quite some time ago I looked into mctrl_gpio) with mctrl_gpio_init_noauto() having a CTS-gpio is just ignored unless the modem ctrl lines are explicitely requestet while with mctrl_gpio_init() it results in an error. Isn't the error the better alternative?
Best regards
Uwe
Signature · 2 lines
Pengutronix e.K. | Uwe Kleine-König | Industrial Linux Solutions | http://www.pengutronix.de/ |
Russell King - ARM Linux admin
maintainerRe: [PATCH 1/6] serial: sa1100: add support for mctrl gpios
Quoted 11 lines · Uwe Kleine-König
Quoted 10 lines · Russell King - ARM Linux admin
Quoted 8 lines · Uwe Kleine-König
drivers/tty/serial/sa1100.c static int sa1100_serial_resume(struct platform_device *dev) · line 863
Quoted 4 lines · Russell King
drivers/tty/serial/sa1100.c +4
-0+static int sa1100_serial_add_one_port (struct sa1100_port *sport,struct platform_device *dev) +{ + sport->port.dev = &dev->dev; + sport->gpios =mctrl_gpio_init_noauto (sport->port.dev,0 );the
_noautofunction was only introduced to ease a transition. I think the driver would benefit to usemctrl_gpio_init()instead.
Quoted 8 lines
Quoted 4 lines
In what way would the driver benefit?
mctrl_gpio_init()requires that there are IRQs for each input GPIO. This is not the case with most SA11x0 platforms, where the GPIO controls are implemented using simple latches, hence that interface is entirely unsuitable.Ah, but then you can only use the outputs reliably here as an edge on (say) CTS stays unnoticed with both
mctrl_gpio_init()andmctrl_gpio_init_noauto().
Right that is a risk with a polled approach, but that is the approach that the SA1100 serial driver has taken ever since it was written almost twenty years ago, and no one has raised any concerns about that until now.
Quoted 5 lines
Unless I miss something (which is quite possible given that it's quite some time ago I looked into
mctrl_gpio) withmctrl_gpio_init_noauto()having a CTS-gpio is just ignored unless the modem ctrl lines are explicitely requestet while withmctrl_gpio_init()it results in an error. Isn't the error the better alternative?
Unless the serial driver polls the modem control line status, which the SA1100 driver continues to do in exactly the same way after this conversion.
Do you suggest that we just regress the driver by ripping out this support that no one has had any problems with, and that is known to work sufficiently in its day, just because we now don't like it?
Signature · 3 lines
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/ FTTC broadband for 0.8mile line in suburbia: sync at 12.1Mbps down 622kbps up According to speedtest.net: 11.9Mbps down 500kbps up
Re: [PATCH 1/6] serial: sa1100: add support for mctrl gpios
Quoted 7 lines · Russell King - ARM Linux admin
Quoted 5 lines · Uwe Kleine-König
Unless I miss something (which is quite possible given that it's quite some time ago I looked into
mctrl_gpio) withmctrl_gpio_init_noauto()having a CTS-gpio is just ignored unless the modem ctrl lines are explicitely requestet while withmctrl_gpio_init()it results in an error. Isn't the error the better alternative?
Quoted 7 lines
Unless the serial driver polls the modem control line status, which the SA1100 driver continues to do in exactly the same way after this conversion.
Do you suggest that we just regress the driver by ripping out this support that no one has had any problems with, and that is known to work sufficiently in its day, just because we now don't like it?
No, of course not. A nice improvement would be to teach gpio_mctrl (or serial core?) about polling. But this is of course out of scope for this patch, so I suggest to stay with mctrl_gpio_init_noauto and document the lack of irq-capability somewhere prominently such that someone who picks up converting mctrl_gpio_init_noauto to mctrl_gpio_init notices this problem before actually hitting it.
Best regards
Uwe
Signature · 2 lines
Pengutronix e.K. | Uwe Kleine-König | Industrial Linux Solutions | http://www.pengutronix.de/ |
PATCH 1/1 serial: sa1100: add note about modem control signals
As suggested by Uwe, add a note indicating that the modem control signals do not support interrupts, which precludes the driver from using mctrl_gpio_init().
---
Uwe, something like this?
drivers/tty/serial/sa1100.c | 3 +++ 1 file changed, 3 insertions(+)
drivers/tty/serial/sa1100.c +3 -0
@@ -949,6 +949,9 @@ static int sa1100_serial_resume(struct platform_device *dev)static int sa1100_serial_add_one_port (struct sa1100_port *sport,struct platform_device *dev) { sport->port.dev = &dev->dev; + +// GPIO driver does not support interrupts for these modem +// control signals, so the serial driver polls them. sport->gpios =mctrl_gpio_init_noauto (sport->port.dev,0 );if (IS_ERR (sport->gpios)) {int err =PTR_ERR (sport->gpios);
Signature · 7 lines
2.7.4 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Re: [PATCH] serial: sa1100: add note about modem control signals
Hello Russell,
Quoted 18 lines · Russell King
As suggested by Uwe, add a note indicating that the modem control signals do not support interrupts, which precludes the driver from using
mctrl_gpio_init().Suggested-by Uwe Kleine-König <[email protected]>Signed-off-by Russell King <[email protected]>---
Uwe, something like this?
drivers/tty/serial/sa1100.c | 3 +++ 1 file changed, 3 insertions(+)drivers/tty/serial/sa1100.c +0
-0
drivers/tty/serial/sa1100.c static int sa1100_serial_resume(struct platform_device *dev) · line 957
Quoted 9 lines
drivers/tty/serial/sa1100.c +3
-0@@ -949,6 +949,9 @@ static int sa1100_serial_resume(struct platform_device *dev)static int sa1100_serial_add_one_port (struct sa1100_port *sport,struct platform_device *dev) { sport->port.dev = &dev->dev; + +// GPIO driver does not support interrupts for these modem +// control signals, so the serial driver polls them. sport->gpios =mctrl_gpio_init_noauto (sport->port.dev,0 );if (IS_ERR (sport->gpios)) {int err =PTR_ERR (sport->gpios);
I would mention that because of this mctrl_gpio_init cannot be used. (And I would have expected C-like comments).
Best regards
Uwe
Signature · 2 lines
Pengutronix e.K. | Uwe Kleine-König | Industrial Linux Solutions | http://www.pengutronix.de/ |
Russell King - ARM Linux admin
maintainerRe: [PATCH] serial: sa1100: add note about modem control signals
Quoted 16 lines · Uwe Kleine-König
Hello Russell,
Quoted 13 lines · Russell King
As suggested by Uwe, add a note indicating that the modem control signals do not support interrupts, which precludes the driver from using
mctrl_gpio_init().Suggested-by Uwe Kleine-König <[email protected]>Signed-off-by Russell King <[email protected]>---
Uwe, something like this?
drivers/tty/serial/sa1100.c | 3 +++ 1 file changed, 3 insertions(+)
Quoted 16 lines
Quoted 5 lines
drivers/tty/serial/sa1100.c +0
-0drivers/tty/serial/sa1100.c static int sa1100_serial_resume(struct platform_device *dev) · line 957
Quoted 9 lines
drivers/tty/serial/sa1100.c +3
-0@@ -949,6 +949,9 @@ static int sa1100_serial_resume(struct platform_device *dev)static int sa1100_serial_add_one_port (struct sa1100_port *sport,struct platform_device *dev) { sport->port.dev = &dev->dev; + +// GPIO driver does not support interrupts for these modem +// control signals, so the serial driver polls them. sport->gpios =mctrl_gpio_init_noauto (sport->port.dev,0 );if (IS_ERR (sport->gpios)) {int err =PTR_ERR (sport->gpios);I would mention that because of this
mctrl_gpio_initcannot be used.
Ok.
Quoted 1 line
(And I would have expected C-like comments).
It seems that Linus has changed his opinion on C99 commenting style, from "it's not real C" to "I prefer it":
https://lore.kernel.org/patchwork/patch/852060/
Yes, this is mostly about the SPDX commenting style, but Linus seems to be expressing a general preference towards "//" style comments over "/* */" comments, especially for new comments.
Specifically see replies #14 and #18, especially #18 where the discussion moves towards trailing-line comments for structure members.
Signature · 3 lines
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/ FTTC broadband for 0.8mile line in suburbia: sync at 12.1Mbps down 622kbps up According to speedtest.net: 11.9Mbps down 500kbps up
PATCH v2 1/1 serial: sa1100: add note about modem control signals
As suggested by Uwe, add a note indicating that the modem control signals do not support interrupts, which precludes the driver from using mctrl_gpio_init().
--- drivers/tty/serial/sa1100.c | 4 ++++ 1 file changed, 4 insertions(+)
drivers/tty/serial/sa1100.c +4 -0
@@ -860,6 +860,10 @@ static int sa1100_serial_resume(struct platform_device *dev)static int sa1100_serial_add_one_port (struct sa1100_port *sport,struct platform_device *dev) { sport->port.dev = &dev->dev; + +// mctrl_gpio_init() requires that the GPIO driver supports interrupts, +// but we need to support GPIO drivers for hardware that has no such +// interrupts. Use mctrl_gpio_init_noauto() instead. sport->gpios =mctrl_gpio_init_noauto (sport->port.dev,0 );if (IS_ERR (sport->gpios)) {int err =PTR_ERR (sport->gpios);
Signature · 7 lines
2.7.4 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Re: [PATCH v2] serial: sa1100: add note about modem control signals
Hello Russell,
Quoted 15 lines · Russell King
As suggested by Uwe, add a note indicating that the modem control signals do not support interrupts, which precludes the driver from using
mctrl_gpio_init().Suggested-by Uwe Kleine-König <[email protected]>Signed-off-by Russell King <[email protected]>--- drivers/tty/serial/sa1100.c | 4 ++++ 1 file changed, 4 insertions(+)drivers/tty/serial/sa1100.c +0
-0
drivers/tty/serial/sa1100.c static int sa1100_serial_resume(struct platform_device *dev) · line 866
Quoted 7 lines
drivers/tty/serial/sa1100.c +4
-0@@ -860,6 +860,10 @@ static int sa1100_serial_resume(struct platform_device *dev)static int sa1100_serial_add_one_port (struct sa1100_port *sport,struct platform_device *dev) { sport->port.dev = &dev->dev; + +// mctrl_gpio_init() requires that the GPIO driver supports interrupts, +// but we need to support GPIO drivers for hardware that has no such +// interrupts. Use mctrl_gpio_init_noauto() instead.
I hope it's not an impostor who claimed to be Linus to spread deviance from K&R :-)
If you want to, squash this in the commit that introduced mctrl_gpio_init_noauto while keeping my Ack on the resulting patch.
Best regards
Uwe
Quoted 7 lines
drivers/tty/serial/sa1100.c +0
-0sport->gpios =mctrl_gpio_init_noauto (sport->port.dev,0 );if (IS_ERR (sport->gpios)) {int err =PTR_ERR (sport->gpios);Signature · 1 line
2.7.4
Signature · 2 lines
Pengutronix e.K. | Uwe Kleine-König | Industrial Linux Solutions | http://www.pengutronix.de/ |
Russell King - ARM Linux admin
maintainerRe: [PATCH v2] serial: sa1100: add note about modem control signals
Quoted 29 lines · Uwe Kleine-König
Hello Russell,
Quoted 15 lines · Russell King
As suggested by Uwe, add a note indicating that the modem control signals do not support interrupts, which precludes the driver from using
mctrl_gpio_init().Suggested-by Uwe Kleine-König <[email protected]>Signed-off-by Russell King <[email protected]>--- drivers/tty/serial/sa1100.c | 4 ++++ 1 file changed, 4 insertions(+)drivers/tty/serial/sa1100.c +0
-0drivers/tty/serial/sa1100.c static int sa1100_serial_resume(struct platform_device *dev) · line 866
Quoted 7 lines
drivers/tty/serial/sa1100.c +4
-0@@ -860,6 +860,10 @@ static int sa1100_serial_resume(struct platform_device *dev)static int sa1100_serial_add_one_port (struct sa1100_port *sport,struct platform_device *dev) { sport->port.dev = &dev->dev; + +// mctrl_gpio_init() requires that the GPIO driver supports interrupts, +// but we need to support GPIO drivers for hardware that has no such +// interrupts. Use mctrl_gpio_init_noauto() instead. I hope it's not an impostor who claimed to be Linus to spread deviance from K&R :-)
Quoted 4 lines
Acked-by Uwe Kleine-König <[email protected]>If you want to, squash this in the commit that introduced
mctrl_gpio_init_noautowhile keeping my Ack on the resulting patch.
I'd prefer to keep it separate to avoid invalidating the acks that I already have on the first patch.
Signature · 3 lines
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/ FTTC broadband for 0.8mile line in suburbia: sync at 12.1Mbps down 622kbps up According to speedtest.net: 11.9Mbps down 500kbps up
PATCH 2/6 ARM: sa1100/assabet: convert serial to gpiod APIs
In reply to Russell King - ARM Linux adminConvert the Assabet serial modem control signals to use the gpiod APIs rather than custom callbacks into platform code.
--- arch/arm/mach-sa1100/assabet.c | 91 +++++++++++++----------------------------- 1 file changed, 28 insertions(+), 63 deletions(-)
arch/arm/mach-sa1100/assabet.c +28 -63
@@ -522,6 +522,29 @@ static const struct gpio_keys_platform_data assabet_keys_pdata = { .rep = 0, }; +static struct gpiod_lookup_table assabet_uart1_gpio_table = { + .dev_id ="sa11x0-uart.1" , + .table = { +GPIO_LOOKUP ("assabet" ,16 ,"dtr" ,GPIO_ACTIVE_LOW ), +GPIO_LOOKUP ("assabet" ,17 ,"rts" ,GPIO_ACTIVE_LOW ), +GPIO_LOOKUP ("assabet" ,25 ,"dcd" ,GPIO_ACTIVE_LOW ), +GPIO_LOOKUP ("assabet" ,26 ,"cts" ,GPIO_ACTIVE_LOW ), +GPIO_LOOKUP ("assabet" ,27 ,"dsr" ,GPIO_ACTIVE_LOW ), + { }, + }, +}; + +static struct gpiod_lookup_table assabet_uart3_gpio_table = { + .dev_id ="sa11x0-uart.3" , + .table = { +GPIO_LOOKUP ("assabet" ,28 ,"cts" ,GPIO_ACTIVE_LOW ), +GPIO_LOOKUP ("assabet" ,29 ,"dsr" ,GPIO_ACTIVE_LOW ), +GPIO_LOOKUP ("assabet" ,30 ,"dcd" ,GPIO_ACTIVE_LOW ), +GPIO_LOOKUP ("assabet" ,31 ,"rng" ,GPIO_ACTIVE_LOW ), + { }, + }, +}; +static void __init assabet_init (void ) {/*
@@ -568,7 +591,10 @@ static void __init assabet_init(void) neponset_resources, ARRAY_SIZE(neponset_resources));#endif }else { +gpiod_add_lookup_table (&assabet_uart1_gpio_table); +gpiod_add_lookup_table (&assabet_uart3_gpio_table);gpiod_add_lookup_table (&assabet_cf_vcc_gpio_table); + sa11x0_register_fixed_regulator(0, &assabet_cf_vcc_pdata, assabet_cf_vcc_consumers, ARRAY_SIZE(assabet_cf_vcc_consumers),
@@ -658,74 +684,13 @@ static void assabet_uart_pm(struct uart_port *port, u_int state, u_int oldstate) {if (port->mapbase == _Ser1UTCR0) {if (state) -ASSABET_BCR_clear (ASSABET_BCR_RS232EN | -ASSABET_BCR_COM_RTS | -ASSABET_BCR_COM_DTR ); -else -ASSABET_BCR_set (ASSABET_BCR_RS232EN | -ASSABET_BCR_COM_RTS | -ASSABET_BCR_COM_DTR ); - } -} - -/* -* Assabet uses COM_RTS and COM_DTR for both UART1 (com port) -* and UART3 (radio module). We only handle them for UART1 here. -*/ -static void assabet_set_mctrl (struct uart_port *port,u_int mctrl) -{ -if (port->mapbase == _Ser1UTCR0) { -u_int set =0 , clear =0 ; - -if (mctrl &TIOCM_RTS ) - clear |=ASSABET_BCR_COM_RTS ; +ASSABET_BCR_clear (ASSABET_BCR_RS232EN );else - set |=ASSABET_BCR_COM_RTS ; - -if (mctrl &TIOCM_DTR ) - clear |=ASSABET_BCR_COM_DTR ; -else - set |=ASSABET_BCR_COM_DTR ; - -ASSABET_BCR_clear (clear); -ASSABET_BCR_set (set); - } -} - -static u_int assabet_get_mctrl (struct uart_port *port) -{ -u_int ret =0 ; -u_int bsr =ASSABET_BSR ; - -/* need 2 reads to read current value */ - bsr =ASSABET_BSR ; - -if (port->mapbase == _Ser1UTCR0) { -if (bsr &ASSABET_BSR_COM_DCD ) - ret |=TIOCM_CD ; -if (bsr &ASSABET_BSR_COM_CTS ) - ret |=TIOCM_CTS ; -if (bsr &ASSABET_BSR_COM_DSR ) - ret |=TIOCM_DSR ; - }else if (port->mapbase == _Ser3UTCR0) { -if (bsr &ASSABET_BSR_RAD_DCD ) - ret |=TIOCM_CD ; -if (bsr &ASSABET_BSR_RAD_CTS ) - ret |=TIOCM_CTS ; -if (bsr &ASSABET_BSR_RAD_DSR ) - ret |=TIOCM_DSR ; -if (bsr &ASSABET_BSR_RAD_RI ) - ret |=TIOCM_RI ; - }else { - ret =TIOCM_CD |TIOCM_CTS |TIOCM_DSR ; +ASSABET_BCR_set (ASSABET_BCR_RS232EN ); } - -return ret; }static struct sa1100_port_fns assabet_port_fns__initdata = { - .set_mctrl = assabet_set_mctrl, - .get_mctrl = assabet_get_mctrl, .pm = assabet_uart_pm, };
Signature · 1 line
2.7.4
PATCH 3/6 ARM: sa1100/h3xxx: convert serial to gpiod APIs
In reply to Russell King - ARM Linux adminConvert the iPAQ H3xxx serial modem control signals to use the gpiod APIs rather than custom callbacks into platform code.
--- arch/arm/mach-sa1100/h3xxx.c | 64 ++++++++------------------------------------ 1 file changed, 11 insertions(+), 53 deletions(-)
arch/arm/mach-sa1100/h3xxx.c +11 -53
@@ -87,57 +87,6 @@ static struct resource h3xxx_flash_resource =/* * H3xxx uart support */ -static struct gpio h3xxx_uart_gpio[] = { - {H3XXX_GPIO_COM_DCD ,GPIOF_IN ,"COM DCD" }, - {H3XXX_GPIO_COM_CTS ,GPIOF_IN ,"COM CTS" }, - {H3XXX_GPIO_COM_RTS ,GPIOF_OUT_INIT_LOW ,"COM RTS" }, -}; - -static bool h3xxx_uart_request_gpios (void ) -{ -static bool h3xxx_uart_gpio_ok; -int rc; - -if (h3xxx_uart_gpio_ok) -return true; - - rc =gpio_request_array (h3xxx_uart_gpio,ARRAY_SIZE (h3xxx_uart_gpio)); -if (rc) -pr_err ("h3xxx_uart_request_gpios: error %d\n" , rc); -else - h3xxx_uart_gpio_ok = true; - -return h3xxx_uart_gpio_ok; -} - -static void h3xxx_uart_set_mctrl (struct uart_port *port,u_int mctrl) -{ -if (port->mapbase == _Ser3UTCR0) { -if (!h3xxx_uart_request_gpios ()) -return ; -gpio_set_value (H3XXX_GPIO_COM_RTS , !(mctrl &TIOCM_RTS )); - } -} - -static u_int h3xxx_uart_get_mctrl (struct uart_port *port) -{ -u_int ret =TIOCM_CD |TIOCM_CTS |TIOCM_DSR ; - -if (port->mapbase == _Ser3UTCR0) { -if (!h3xxx_uart_request_gpios ()) -return ret; -/* -* DCD and CTS bits are inverted in GPLR by RS232 transceiver -*/ -if (gpio_get_value (H3XXX_GPIO_COM_DCD )) - ret &= ~TIOCM_CD ; -if (gpio_get_value (H3XXX_GPIO_COM_CTS )) - ret &= ~TIOCM_CTS ; - } - -return ret; -} -static void h3xxx_uart_pm (struct uart_port *port,u_int state,u_int oldstate) {if (port->mapbase == _Ser3UTCR0) {
@@ -170,12 +119,20 @@ static int h3xxx_uart_set_wake(struct uart_port *port, u_int enable) }static struct sa1100_port_fns h3xxx_port_fns__initdata = { - .set_mctrl = h3xxx_uart_set_mctrl, - .get_mctrl = h3xxx_uart_get_mctrl, .pm = h3xxx_uart_pm, .set_wake = h3xxx_uart_set_wake, }; +static struct gpiod_lookup_table h3xxx_uart3_gpio_table = { + .dev_id ="sa11x0-uart.3" , + .table = { +GPIO_LOOKUP ("gpio" ,H3XXX_GPIO_COM_DCD ,"dcd" ,GPIO_ACTIVE_LOW ), +GPIO_LOOKUP ("gpio" ,H3XXX_GPIO_COM_CTS ,"cts" ,GPIO_ACTIVE_LOW ), +GPIO_LOOKUP ("gpio" ,H3XXX_GPIO_COM_RTS ,"rts" ,GPIO_ACTIVE_LOW ), + { }, + }, +}; +/* * EGPIO */
@@ -283,6 +240,7 @@ static struct gpiod_lookup_table h3xxx_pcmcia_gpio_table = {void __init h3xxx_mach_init (void ) {gpiod_add_lookup_table (&h3xxx_pcmcia_gpio_table); +gpiod_add_lookup_table (&h3xxx_uart3_gpio_table);sa1100_register_uart_fns (&h3xxx_port_fns);sa11x0_register_mtd (&h3xxx_flash_data, &h3xxx_flash_resource,1 );platform_add_devices (h3xxx_devices,ARRAY_SIZE (h3xxx_devices));
Signature · 1 line
2.7.4
PATCH 4/6 ARM: sa1100/badge4: remove commented out modem control initialisers
In reply to Russell King - ARM Linux adminRemove the commented out modem control initialisers. These are doing nothing useful.
--- arch/arm/mach-sa1100/badge4.c | 2 -- 1 file changed, 2 deletions(-)
arch/arm/mach-sa1100/badge4.c +0 -2
@@ -315,8 +315,6 @@ badge4_uart_pm(struct uart_port *port, u_int state, u_int oldstate) }static struct sa1100_port_fns badge4_port_fns__initdata = { -//.get_mctrl = badge4_get_mctrl, -//.set_mctrl = badge4_set_mctrl, .pm = badge4_uart_pm, };
Signature · 1 line
2.7.4
PATCH 5/6 ARM: sa1100/hackkit: remove empty serial mctrl functions
In reply to Russell King - ARM Linux adminRemove the empty serial modem control signal functions from hackkit as these are unnecessary - the core code can copes fine without these.
--- arch/arm/mach-sa1100/hackkit.c | 48 ------------------------------------------ 1 file changed, 48 deletions(-)
arch/arm/mach-sa1100/hackkit.c +0 -48
@@ -49,8 +49,6 @@/* init funcs */ static void __init hackkit_map_io (void ); -static u_int hackkit_get_mctrl (struct uart_port *port); -static void hackkit_set_mctrl (struct uart_port *port,u_int mctrl);static void hackkit_uart_pm (struct uart_port *port,u_int state,u_int oldstate);/**********************************************************************
@@ -71,8 +69,6 @@ static struct map_desc hackkit_io_desc[] __initdata = { };static struct sa1100_port_fns hackkit_port_fns__initdata = { - .set_mctrl = hackkit_set_mctrl, - .get_mctrl = hackkit_get_mctrl, .pm = hackkit_uart_pm, };
@@ -105,50 +101,6 @@ static void hackkit_uart_pm(struct uart_port *port, u_int state, u_int oldstate)/* TODO: switch on/off uart in powersave mode */ } -/* -* Note! this can be called from IRQ context. -* FIXME: No modem ctrl lines yet. -*/ -static void hackkit_set_mctrl (struct uart_port *port,u_int mctrl) -{ -#if 0 -if (port->mapbase == _Ser1UTCR0) { -u_int set =0 , clear =0 ; - -if (mctrl &TIOCM_RTS ) - set |=PT_CTRL2_RS1_RTS ; -else - clear |=PT_CTRL2_RS1_RTS ; - -if (mctrl &TIOCM_DTR ) - set |=PT_CTRL2_RS1_DTR ; -else - clear |=PT_CTRL2_RS1_DTR ; - -PTCTRL2_clear (clear); -PTCTRL2_set (set); - } -#endif -} - -static u_int hackkit_get_mctrl (struct uart_port *port) -{ -u_int ret =0 ; -#if 0 -u_int irqsr =PT_IRQSR ; - -/* need 2 reads to read current value */ - irqsr =PT_IRQSR ; - -/* TODO: check IRQ source register for modem/com -status lines and set them correctly. */ -#endif - - ret =TIOCM_CD |TIOCM_CTS |TIOCM_DSR ; - -return ret; -} -static struct mtd_partition hackkit_partitions[] = { { .name ="BLOB" ,
Signature · 1 line
2.7.4
PATCH 6/6 ARM: sa1100/neponset: convert serial to use gpiod APIs
In reply to Russell King - ARM Linux adminConvert the serial modem control signals to use the gpiod APIs rather than the private platform callbacks.
--- arch/arm/mach-sa1100/neponset.c | 109 +++++++++++----------------------------- 1 file changed, 28 insertions(+), 81 deletions(-)
arch/arm/mach-sa1100/neponset.c +28 -81
@@ -11,7 +11,6 @@#include <linux/irq.h> #include <linux/kernel.h> #include <linux/module.h> -#include <linux/platform_data/sa11x0-serial.h> #include <linux/platform_device.h> #include <linux/pm.h> #include <linux/serial_core.h>
@@ -49,23 +48,8 @@#define IRR_SA1111 (1 << 2)#define NCR_NGPIO 7 - -#define MDM_CTL0_RTS1 (1 << 0) -#define MDM_CTL0_DTR1 (1 << 1) -#define MDM_CTL0_RTS2 (1 << 2) -#define MDM_CTL0_DTR2 (1 << 3)#define MDM_CTL0_NGPIO 4 - -#define MDM_CTL1_CTS1 (1 << 0) -#define MDM_CTL1_DSR1 (1 << 1) -#define MDM_CTL1_DCD1 (1 << 2) -#define MDM_CTL1_CTS2 (1 << 3) -#define MDM_CTL1_DSR2 (1 << 4) -#define MDM_CTL1_DCD2 (1 << 5)#define MDM_CTL1_NGPIO 6 - -#define AUD_SEL_1341 (1 << 0) -#define AUD_MUTE_1341 (1 << 1)#define AUD_NGPIO 2extern void sa1110_mb_disable (void );
@@ -97,6 +81,30 @@ struct neponset_drvdata {struct gpio_chip *gpio[4 ]; }; +static struct gpiod_lookup_table neponset_uart1_gpio_table = { + .dev_id ="sa11x0-uart.1" , + .table = { +GPIO_LOOKUP ("neponset-mdm-ctl0" ,2 ,"rts" ,GPIO_ACTIVE_LOW ), +GPIO_LOOKUP ("neponset-mdm-ctl0" ,3 ,"dtr" ,GPIO_ACTIVE_LOW ), +GPIO_LOOKUP ("neponset-mdm-ctl1" ,3 ,"cts" ,GPIO_ACTIVE_LOW ), +GPIO_LOOKUP ("neponset-mdm-ctl1" ,4 ,"dsr" ,GPIO_ACTIVE_LOW ), +GPIO_LOOKUP ("neponset-mdm-ctl1" ,5 ,"dcd" ,GPIO_ACTIVE_LOW ), + { }, + }, +}; + +static struct gpiod_lookup_table neponset_uart3_gpio_table = { + .dev_id ="sa11x0-uart.3" , + .table = { +GPIO_LOOKUP ("neponset-mdm-ctl0" ,0 ,"rts" ,GPIO_ACTIVE_LOW ), +GPIO_LOOKUP ("neponset-mdm-ctl0" ,1 ,"dtr" ,GPIO_ACTIVE_LOW ), +GPIO_LOOKUP ("neponset-mdm-ctl1" ,0 ,"cts" ,GPIO_ACTIVE_LOW ), +GPIO_LOOKUP ("neponset-mdm-ctl1" ,1 ,"dsr" ,GPIO_ACTIVE_LOW ), +GPIO_LOOKUP ("neponset-mdm-ctl1" ,2 ,"dcd" ,GPIO_ACTIVE_LOW ), + { }, + }, +}; +static struct gpiod_lookup_table neponset_pcmcia_table = { .dev_id ="1800" , .table = {
@@ -124,69 +132,6 @@ void neponset_ncr_frob(unsigned int mask, unsigned int val) }EXPORT_SYMBOL (neponset_ncr_frob); -static void neponset_set_mctrl (struct uart_port *port,u_int mctrl) -{ -struct neponset_drvdata *n = nep; -unsigned long mask, val =0 ; - -if (!n) -return ; - -if (port->mapbase == _Ser1UTCR0) { - mask =MDM_CTL0_RTS2 |MDM_CTL0_DTR2 ; - -if (!(mctrl &TIOCM_RTS )) - val |=MDM_CTL0_RTS2 ; - -if (!(mctrl &TIOCM_DTR )) - val |=MDM_CTL0_DTR2 ; - }else if (port->mapbase == _Ser3UTCR0) { - mask =MDM_CTL0_RTS1 |MDM_CTL0_DTR1 ; - -if (!(mctrl &TIOCM_RTS )) - val |=MDM_CTL0_RTS1 ; - -if (!(mctrl &TIOCM_DTR )) - val |=MDM_CTL0_DTR1 ; - } - - n->gpio[1 ]->set_multiple (n->gpio[1 ], &mask, &val); -} - -static u_int neponset_get_mctrl (struct uart_port *port) -{ -void __iomem *base = nep->base; -u_int ret =TIOCM_CD |TIOCM_CTS |TIOCM_DSR ; -u_int mdm_ctl1; - -if (!base) -return ret; - - mdm_ctl1 =readb_relaxed (base +MDM_CTL_1 ); -if (port->mapbase == _Ser1UTCR0) { -if (mdm_ctl1 &MDM_CTL1_DCD2 ) - ret &= ~TIOCM_CD ; -if (mdm_ctl1 &MDM_CTL1_CTS2 ) - ret &= ~TIOCM_CTS ; -if (mdm_ctl1 &MDM_CTL1_DSR2 ) - ret &= ~TIOCM_DSR ; - }else if (port->mapbase == _Ser3UTCR0) { -if (mdm_ctl1 &MDM_CTL1_DCD1 ) - ret &= ~TIOCM_CD ; -if (mdm_ctl1 &MDM_CTL1_CTS1 ) - ret &= ~TIOCM_CTS ; -if (mdm_ctl1 &MDM_CTL1_DSR1 ) - ret &= ~TIOCM_DSR ; - } - -return ret; -} - -static struct sa1100_port_fns neponset_port_fns = { - .set_mctrl = neponset_set_mctrl, - .get_mctrl = neponset_get_mctrl, -}; -/* * Install handler for Neponset IRQ. Note that we have to loop here * since the ETHERNET and USAR IRQs are level based, and we need to
@@ -388,6 +333,8 @@ static int neponset_probe(struct platform_device *dev) d->base +AUD_CTL ,AUD_NGPIO , false, neponset_aud_names); +gpiod_add_lookup_table (&neponset_uart1_gpio_table); +gpiod_add_lookup_table (&neponset_uart3_gpio_table);gpiod_add_lookup_table (&neponset_pcmcia_table);/*
@@ -402,8 +349,6 @@ static int neponset_probe(struct platform_device *dev) d->irq_base, d->irq_base + NEP_IRQ_NR - 1); nep = d; -sa1100_register_uart_fns (&neponset_port_fns); -/* Ensure that the memory bus request/grant signals are setup */ sa1110_mb_disable ();
@@ -442,6 +387,8 @@ static int neponset_remove(struct platform_device *dev)platform_device_unregister (d->smc91x);gpiod_remove_lookup_table (&neponset_pcmcia_table); +gpiod_remove_lookup_table (&neponset_uart3_gpio_table); +gpiod_remove_lookup_table (&neponset_uart1_gpio_table);irq_set_chained_handler (irq,NULL );irq_free_descs (d->irq_base,NEP_IRQ_NR );
Signature · 1 line
2.7.4