Add support for bcm4378 on Apple platforms
Subsystems (7)
v2 cover Add support for bcm4378 on Apple platforms
Hi,
This series adds support for bcm4378 found on Apple platforms, and has been tested on the Apple Mac Mini. It is a re-posting of a subset of Hector's previous 38 patch series, and it is believed that the comments from that review were addressed.
(I'm just the middle man; please don't complain if something has been missed.)
v2:
- sending for wireless-next
- fixed up %ld -> %zd for size_t
- added reviewed-bys
arch/arm64/boot/dts/apple/t8103-j274.dts | 4 + arch/arm64/boot/dts/apple/t8103-j293.dts | 4 + arch/arm64/boot/dts/apple/t8103-j313.dts | 4 + arch/arm64/boot/dts/apple/t8103-j456.dts | 4 + arch/arm64/boot/dts/apple/t8103-j457.dts | 4 + arch/arm64/boot/dts/apple/t8103-jxxx.dtsi | 2 + .../net/wireless/broadcom/brcm80211/brcmfmac/bus.h | 19 +- .../wireless/broadcom/brcm80211/brcmfmac/chip.c | 2 + .../wireless/broadcom/brcm80211/brcmfmac/common.c | 12 +- .../wireless/broadcom/brcm80211/brcmfmac/common.h | 1 + .../broadcom/brcm80211/brcmfmac/firmware.c | 115 ++++-- .../broadcom/brcm80211/brcmfmac/firmware.h | 4 +- .../wireless/broadcom/brcm80211/brcmfmac/msgbuf.h | 4 +- .../net/wireless/broadcom/brcm80211/brcmfmac/of.c | 12 +- .../wireless/broadcom/brcm80211/brcmfmac/pcie.c | 431 +++++++++++++++++++-- .../wireless/broadcom/brcm80211/brcmfmac/sdio.c | 38 +- .../wireless/broadcom/brcm80211/brcmfmac/sdio.h | 2 + .../net/wireless/broadcom/brcm80211/brcmfmac/usb.c | 23 +- .../broadcom/brcm80211/include/brcm_hw_ids.h | 2 + include/linux/bcma/bcma_driver_chipcommon.h | 1 + 21 files changed, 610 insertions(+), 117 deletions(-)
Signature · 2 lines
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/ FTTP is here! 40Mbps down 10Mbps up. Decent connectivity at last!
PATCH v2 1/12 dt-bindings: net: bcm4329-fmac: Add Apple properties & chips
From: Hector Martin <[email protected]>
This binding is currently used for SDIO devices, but these chips are also used as PCIe devices on DT platforms and may be represented in the DT. Re-use the existing binding and add chip compatibles used by Apple T2 and M1 platforms (the T2 ones are not known to be used in DT platforms, but we might as well document them).
Then, add properties required for firmware selection and calibration on M1 machines.
--- .../net/wireless/brcm,bcm4329-fmac.yaml | 39 +++++++++++++++++-- 1 file changed, 35 insertions(+), 4 deletions(-)
Documentation/devicetree/bindings/net/wireless/brcm,bcm4329-fmac.yaml +35 -4
@@ -4,7 +4,7 @@ $id: http://devicetree.org/schemas/net/wireless/brcm,bcm4329-fmac.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: Broadcom BCM4329 family fullmac wireless SDIO devices +title: Broadcom BCM4329 family fullmac wireless SDIO/PCIE devices maintainers: - Arend van Spriel <[email protected]>
@@ -41,11 +41,17 @@ title: Broadcom BCM4329 family fullmac wireless SDIO devices - cypress,cyw4373-fmac - cypress,cyw43012-fmac - const: brcm,bcm4329-fmac - - const: brcm,bcm4329-fmac + - enum: + - brcm,bcm4329-fmac + - pci14e4,43dc # BCM4355 + - pci14e4,4464 # BCM4364 + - pci14e4,4488 # BCM4377 + - pci14e4,4425 # BCM4378 + - pci14e4,4433 # BCM4387 reg: - description: SDIO function number for the device, for most cases - this will be 1. + description: SDIO function number for the device (for most cases + this will be 1) or PCI device identifier. interrupts: maxItems: 1
@@ -85,6 +91,31 @@ title: Broadcom BCM4329 family fullmac wireless SDIO devices takes precedence. type: boolean + brcm,cal-blob: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: A per-device calibration blob for the Wi-Fi radio. This + should be filled in by the bootloader from platform configuration + data, if necessary, and will be uploaded to the device if present. + + brcm,board-type: + $ref: /schemas/types.yaml#/definitions/string + description: Overrides the board type, which is normally the compatible of + the root node. This can be used to decouple the overall system board or + device name from the board type for WiFi purposes, which is used to + construct firmware and NVRAM configuration filenames, allowing for + multiple devices that share the same module or characteristics for the + WiFi subsystem to share the same firmware/NVRAM files. On Apple platforms, + this should be the Apple module-instance codename prefixed by "apple,", + e.g. "apple,honshu". + + apple,antenna-sku: + $ref: /schemas/types.yaml#/definitions/string + description: Antenna SKU used to identify a specific antenna configuration + on Apple platforms. This is use to build firmware filenames, to allow + platforms with different antenna configs to have different firmware and/or + NVRAM. This would normally be filled in by the bootloader from platform + configuration data. + required: - compatible - reg
Signature · 1 line
2.30.2
Re: [PATCH wireless-next v2 01/12] dt-bindings: net: bcm4329-fmac: Add Apple properties & chips
Quoted 55 lines · Russell King
From: Hector Martin <[email protected]>
This binding is currently used for SDIO devices, but these chips are also used as PCIe devices on DT platforms and may be represented in the DT. Re-use the existing binding and add chip compatibles used by Apple T2 and M1 platforms (the T2 ones are not known to be used in DT platforms, but we might as well document them).
Then, add properties required for firmware selection and calibration on M1 machines.
Reviewed-by Linus Walleij <[email protected]>Signed-off-by Hector Martin <[email protected]>Reviewed-by Mark Kettenis <[email protected]>Reviewed-by Rob Herring <[email protected]>Signed-off-by Russell King (Oracle) <[email protected]>--- .../net/wireless/brcm,bcm4329-fmac.yaml | 39 +++++++++++++++++-- 1 file changed, 35 insertions(+), 4 deletions(-)Documentation/devicetree/bindings/net/wireless/brcm,bcm4329-fmac.yaml +10
-4@@ -4,7 +4,7 @@ $id: http://devicetree.org/schemas/net/wireless/brcm,bcm4329-fmac.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: Broadcom BCM4329 family fullmac wireless SDIO devices +title: Broadcom BCM4329 family fullmac wireless SDIO/PCIE devices maintainers: - Arend van Spriel <[email protected]>@@ -41,11 +41,17 @@ title: Broadcom BCM4329 family fullmac wireless SDIO devices - cypress,cyw4373-fmac - cypress,cyw43012-fmac - const: brcm,bcm4329-fmac - - const: brcm,bcm4329-fmac + - enum: + - brcm,bcm4329-fmac + - pci14e4,43dc # BCM4355 + - pci14e4,4464 # BCM4364 + - pci14e4,4488 # BCM4377 + - pci14e4,4425 # BCM4378 + - pci14e4,4433 # BCM4387 reg: - description: SDIO function number for the device, for most cases - this will be 1. + description: SDIO function number for the device (for most cases + this will be 1) or PCI device identifier. interrupts: maxItems: 1
Documentation/devicetree/bindings/net/wireless/brcm,bcm4329-fmac.yaml title: Broadcom BCM4329 family fullmac wireless SDIO devices · line 98
Quoted 8 lines
Documentation/devicetree/bindings/net/wireless/brcm,bcm4329-fmac.yaml +5
-0@@ -85,6 +91,31 @@ title: Broadcom BCM4329 family fullmac wireless SDIO devices takes precedence. type: boolean + brcm,cal-blob: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: A per-device calibration blob for the Wi-Fi radio. This + should be filled in by the bootloader from platform configuration + data, if necessary, and will be uploaded to the device if present.
Is this a leftover from a previous revision of the patchset? Because as far as I can tell, the CLM blob is (still) being loaded via firmware, and no additional parsing has been added for this particular OF property. Should it be dropped?
The rest looks quite OK.
Kind regards,
Alvin
Documentation/devicetree/bindings/net/wireless/brcm,bcm4329-fmac.yaml title: Broadcom BCM4329 family fullmac wireless SDIO devices · line 109
Quoted 11 lines
Documentation/devicetree/bindings/net/wireless/brcm,bcm4329-fmac.yaml +11
-0+ + brcm,board-type: + $ref: /schemas/types.yaml#/definitions/string + description: Overrides the board type, which is normally the compatible of + the root node. This can be used to decouple the overall system board or + device name from the board type for WiFi purposes, which is used to + construct firmware and NVRAM configuration filenames, allowing for + multiple devices that share the same module or characteristics for the + WiFi subsystem to share the same firmware/NVRAM files. On Apple platforms, + this should be the Apple module-instance codename prefixed by "apple,", + e.g. "apple,honshu".
nit: s/WiFi/Wi-Fi/
Quoted 15 lines
Documentation/devicetree/bindings/net/wireless/brcm,bcm4329-fmac.yaml +9
-0+ + apple,antenna-sku: + $ref: /schemas/types.yaml#/definitions/string + description: Antenna SKU used to identify a specific antenna configuration + on Apple platforms. This is use to build firmware filenames, to allow + platforms with different antenna configs to have different firmware and/or + NVRAM. This would normally be filled in by the bootloader from platform + configuration data. + required: - compatible - regSignature · 1 line
2.30.2
Re: [PATCH wireless-next v2 01/12] dt-bindings: net: bcm4329-fmac: Add Apple properties & chips
Quoted 59 lines · Alvin Šipraga
Quoted 58 lines · Russell King
From: Hector Martin <[email protected]>
This binding is currently used for SDIO devices, but these chips are also used as PCIe devices on DT platforms and may be represented in the DT. Re-use the existing binding and add chip compatibles used by Apple T2 and M1 platforms (the T2 ones are not known to be used in DT platforms, but we might as well document them).
Then, add properties required for firmware selection and calibration on M1 machines.
Reviewed-by Linus Walleij <[email protected]>Signed-off-by Hector Martin <[email protected]>Reviewed-by Mark Kettenis <[email protected]>Reviewed-by Rob Herring <[email protected]>Signed-off-by Russell King (Oracle) <[email protected]>--- .../net/wireless/brcm,bcm4329-fmac.yaml | 39 +++++++++++++++++-- 1 file changed, 35 insertions(+), 4 deletions(-)Documentation/devicetree/bindings/net/wireless/brcm,bcm4329-fmac.yaml +10
-4@@ -4,7 +4,7 @@ $id: http://devicetree.org/schemas/net/wireless/brcm,bcm4329-fmac.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: Broadcom BCM4329 family fullmac wireless SDIO devices +title: Broadcom BCM4329 family fullmac wireless SDIO/PCIE devices maintainers: - Arend van Spriel <[email protected]>@@ -41,11 +41,17 @@ title: Broadcom BCM4329 family fullmac wireless SDIO devices - cypress,cyw4373-fmac - cypress,cyw43012-fmac - const: brcm,bcm4329-fmac - - const: brcm,bcm4329-fmac + - enum: + - brcm,bcm4329-fmac + - pci14e4,43dc # BCM4355 + - pci14e4,4464 # BCM4364 + - pci14e4,4488 # BCM4377 + - pci14e4,4425 # BCM4378 + - pci14e4,4433 # BCM4387 reg: - description: SDIO function number for the device, for most cases - this will be 1. + description: SDIO function number for the device (for most cases + this will be 1) or PCI device identifier. interrupts: maxItems: 1@@ -85,6 +91,31 @@ title: Broadcom BCM4329 family fullmac wireless SDIO devices takes precedence. type: boolean
Quoted 10 lines
Documentation/devicetree/bindings/net/wireless/brcm,bcm4329-fmac.yaml title: Broadcom BCM4329 family fullmac wireless SDIO devices · line 98
Quoted 5 lines
Documentation/devicetree/bindings/net/wireless/brcm,bcm4329-fmac.yaml +5
-0+ brcm,cal-blob: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: A per-device calibration blob for the Wi-Fi radio. This + should be filled in by the bootloader from platform configuration + data, if necessary, and will be uploaded to the device if present.Is this a leftover from a previous revision of the patchset? Because as far as I can tell, the CLM blob is (still) being loaded via firmware, and no additional parsing has been added for this particular OF property. Should it be dropped?
It does appear to be unparsed, but I don't know whether it's needed for the binding or not. I'll wait for the Asahi folk to review your comment before possibly removing it.
Thanks!
Signature · 2 lines
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/ FTTP is here! 40Mbps down 10Mbps up. Decent connectivity at last!
Re: [PATCH wireless-next v2 01/12] dt-bindings: net: bcm4329-fmac: Add Apple properties & chips
Quoted 71 lines · Russell King (Oracle)
Quoted 59 lines · Alvin Šipraga
Quoted 58 lines · Russell King
From: Hector Martin <[email protected]>
This binding is currently used for SDIO devices, but these chips are also used as PCIe devices on DT platforms and may be represented in the DT. Re-use the existing binding and add chip compatibles used by Apple T2 and M1 platforms (the T2 ones are not known to be used in DT platforms, but we might as well document them).
Then, add properties required for firmware selection and calibration on M1 machines.
Reviewed-by Linus Walleij <[email protected]>Signed-off-by Hector Martin <[email protected]>Reviewed-by Mark Kettenis <[email protected]>Reviewed-by Rob Herring <[email protected]>Signed-off-by Russell King (Oracle) <[email protected]>--- .../net/wireless/brcm,bcm4329-fmac.yaml | 39 +++++++++++++++++-- 1 file changed, 35 insertions(+), 4 deletions(-)Documentation/devicetree/bindings/net/wireless/brcm,bcm4329-fmac.yaml +10
-4@@ -4,7 +4,7 @@ $id: http://devicetree.org/schemas/net/wireless/brcm,bcm4329-fmac.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: Broadcom BCM4329 family fullmac wireless SDIO devices +title: Broadcom BCM4329 family fullmac wireless SDIO/PCIE devices maintainers: - Arend van Spriel <[email protected]>@@ -41,11 +41,17 @@ title: Broadcom BCM4329 family fullmac wireless SDIO devices - cypress,cyw4373-fmac - cypress,cyw43012-fmac - const: brcm,bcm4329-fmac - - const: brcm,bcm4329-fmac + - enum: + - brcm,bcm4329-fmac + - pci14e4,43dc # BCM4355 + - pci14e4,4464 # BCM4364 + - pci14e4,4488 # BCM4377 + - pci14e4,4425 # BCM4378 + - pci14e4,4433 # BCM4387 reg: - description: SDIO function number for the device, for most cases - this will be 1. + description: SDIO function number for the device (for most cases + this will be 1) or PCI device identifier. interrupts: maxItems: 1@@ -85,6 +91,31 @@ title: Broadcom BCM4329 family fullmac wireless SDIO devices takes precedence. type: booleanQuoted 10 lines
Documentation/devicetree/bindings/net/wireless/brcm,bcm4329-fmac.yaml title: Broadcom BCM4329 family fullmac wireless SDIO devices · line 98
Quoted 5 lines
Documentation/devicetree/bindings/net/wireless/brcm,bcm4329-fmac.yaml +5
-0+ brcm,cal-blob: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: A per-device calibration blob for the Wi-Fi radio. This + should be filled in by the bootloader from platform configuration + data, if necessary, and will be uploaded to the device if present.Is this a leftover from a previous revision of the patchset? Because as far as I can tell, the CLM blob is (still) being loaded via firmware, and no additional parsing has been added for this particular OF property. Should it be dropped?
Quoted 3 lines
It does appear to be unparsed, but I don't know whether it's needed for the binding or not. I'll wait for the Asahi folk to review your comment before possibly removing it.
Okay, the answer is, it is still very much part of the binding, and the m1n1 boot loader populates it.
This series is a subset of a larger series (remember the previous 34 or 35 patch series?), so there are things in the binding document which are not included in this series.
I don't think it makes sense to break up the binding document given that it has already been reviewed several times in its current state, should we really remove this one property and throw away all that review effort.
Signature · 2 lines
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/ FTTP is here! 40Mbps down 10Mbps up. Decent connectivity at last!
Re: [PATCH wireless-next v2 01/12] dt-bindings: net: bcm4329-fmac: Add Apple properties & chips
Quoted 82 lines
Date: Mon, 12 Sep 2022 15:01:06 +0100
From: "Russell King (Oracle)" <[email protected]>Quoted 71 lines · Russell King (Oracle)
Quoted 59 lines · Alvin Šipraga
Quoted 58 lines · Russell King
From: Hector Martin <[email protected]>
This binding is currently used for SDIO devices, but these chips are also used as PCIe devices on DT platforms and may be represented in the DT. Re-use the existing binding and add chip compatibles used by Apple T2 and M1 platforms (the T2 ones are not known to be used in DT platforms, but we might as well document them).
Then, add properties required for firmware selection and calibration on M1 machines.
Reviewed-by Linus Walleij <[email protected]>Signed-off-by Hector Martin <[email protected]>Reviewed-by Mark Kettenis <[email protected]>Reviewed-by Rob Herring <[email protected]>Signed-off-by Russell King (Oracle) <[email protected]>--- .../net/wireless/brcm,bcm4329-fmac.yaml | 39 +++++++++++++++++-- 1 file changed, 35 insertions(+), 4 deletions(-)Documentation/devicetree/bindings/net/wireless/brcm,bcm4329-fmac.yaml +10
-4@@ -4,7 +4,7 @@ $id: http://devicetree.org/schemas/net/wireless/brcm,bcm4329-fmac.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: Broadcom BCM4329 family fullmac wireless SDIO devices +title: Broadcom BCM4329 family fullmac wireless SDIO/PCIE devices maintainers: - Arend van Spriel <[email protected]>@@ -41,11 +41,17 @@ title: Broadcom BCM4329 family fullmac wireless SDIO devices - cypress,cyw4373-fmac - cypress,cyw43012-fmac - const: brcm,bcm4329-fmac - - const: brcm,bcm4329-fmac + - enum: + - brcm,bcm4329-fmac + - pci14e4,43dc # BCM4355 + - pci14e4,4464 # BCM4364 + - pci14e4,4488 # BCM4377 + - pci14e4,4425 # BCM4378 + - pci14e4,4433 # BCM4387 reg: - description: SDIO function number for the device, for most cases - this will be 1. + description: SDIO function number for the device (for most cases + this will be 1) or PCI device identifier. interrupts: maxItems: 1@@ -85,6 +91,31 @@ title: Broadcom BCM4329 family fullmac wireless SDIO devices takes precedence. type: booleanQuoted 10 lines
Documentation/devicetree/bindings/net/wireless/brcm,bcm4329-fmac.yaml title: Broadcom BCM4329 family fullmac wireless SDIO devices · line 98
Quoted 5 lines
Documentation/devicetree/bindings/net/wireless/brcm,bcm4329-fmac.yaml +5
-0+ brcm,cal-blob: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: A per-device calibration blob for the Wi-Fi radio. This + should be filled in by the bootloader from platform configuration + data, if necessary, and will be uploaded to the device if present.Is this a leftover from a previous revision of the patchset? Because as far as I can tell, the CLM blob is (still) being loaded via firmware, and no additional parsing has been added for this particular OF property. Should it be dropped?
Quoted 3 lines
It does appear to be unparsed, but I don't know whether it's needed for the binding or not. I'll wait for the Asahi folk to review your comment before possibly removing it.
Okay, the answer is, it is still very much part of the binding, and the m1n1 boot loader populates it.
Quoted 8 lines
This series is a subset of a larger series (remember the previous 34 or 35 patch series?), so there are things in the binding document which are not included in this series.
I don't think it makes sense to break up the binding document given that it has already been reviewed several times in its current state, should we really remove this one property and throw away all that review effort.
The OpenBSD driver already uses these properties. So even if the Linux driver doesn't use this yet, there is an existing implementation that does. That should be good enough for it to be included in the binding isn't it?
Alvin Šipraga
Reviewed-byRe: [PATCH wireless-next v2 01/12] dt-bindings: net: bcm4329-fmac: Add Apple properties & chips
Hi both,
Quoted 91 lines · Mark Kettenis
Quoted 82 lines
Date: Mon, 12 Sep 2022 15:01:06 +0100
From: "Russell King (Oracle)" <[email protected]>Quoted 71 lines · Russell King (Oracle)
Quoted 59 lines · Alvin Šipraga
Quoted 58 lines · Russell King
From: Hector Martin <[email protected]>
This binding is currently used for SDIO devices, but these chips are also used as PCIe devices on DT platforms and may be represented in the DT. Re-use the existing binding and add chip compatibles used by Apple T2 and M1 platforms (the T2 ones are not known to be used in DT platforms, but we might as well document them).
Then, add properties required for firmware selection and calibration on M1 machines.
Reviewed-by Linus Walleij <[email protected]>Signed-off-by Hector Martin <[email protected]>Reviewed-by Mark Kettenis <[email protected]>Reviewed-by Rob Herring <[email protected]>Signed-off-by Russell King (Oracle) <[email protected]>--- .../net/wireless/brcm,bcm4329-fmac.yaml | 39 +++++++++++++++++-- 1 file changed, 35 insertions(+), 4 deletions(-)Documentation/devicetree/bindings/net/wireless/brcm,bcm4329-fmac.yaml +10
-4@@ -4,7 +4,7 @@ $id: http://devicetree.org/schemas/net/wireless/brcm,bcm4329-fmac.yaml $schema: http://devicetree.org/meta-schemas/core.yaml -title: Broadcom BCM4329 family fullmac wireless SDIO devices +title: Broadcom BCM4329 family fullmac wireless SDIO/PCIE devices maintainers: - Arend van Spriel <[email protected]>@@ -41,11 +41,17 @@ title: Broadcom BCM4329 family fullmac wireless SDIO devices - cypress,cyw4373-fmac - cypress,cyw43012-fmac - const: brcm,bcm4329-fmac - - const: brcm,bcm4329-fmac + - enum: + - brcm,bcm4329-fmac + - pci14e4,43dc # BCM4355 + - pci14e4,4464 # BCM4364 + - pci14e4,4488 # BCM4377 + - pci14e4,4425 # BCM4378 + - pci14e4,4433 # BCM4387 reg: - description: SDIO function number for the device, for most cases - this will be 1. + description: SDIO function number for the device (for most cases + this will be 1) or PCI device identifier. interrupts: maxItems: 1@@ -85,6 +91,31 @@ title: Broadcom BCM4329 family fullmac wireless SDIO devices takes precedence. type: booleanQuoted 10 lines
Documentation/devicetree/bindings/net/wireless/brcm,bcm4329-fmac.yaml title: Broadcom BCM4329 family fullmac wireless SDIO devices · line 98
Quoted 5 lines
Documentation/devicetree/bindings/net/wireless/brcm,bcm4329-fmac.yaml +5
-0+ brcm,cal-blob: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: A per-device calibration blob for the Wi-Fi radio. This + should be filled in by the bootloader from platform configuration + data, if necessary, and will be uploaded to the device if present.Is this a leftover from a previous revision of the patchset? Because as far as I can tell, the CLM blob is (still) being loaded via firmware, and no additional parsing has been added for this particular OF property. Should it be dropped?
Quoted 3 lines
It does appear to be unparsed, but I don't know whether it's needed for the binding or not. I'll wait for the Asahi folk to review your comment before possibly removing it.
Okay, the answer is, it is still very much part of the binding, and the m1n1 boot loader populates it.
Quoted 8 lines
This series is a subset of a larger series (remember the previous 34 or 35 patch series?), so there are things in the binding document which are not included in this series.
I don't think it makes sense to break up the binding document given that it has already been reviewed several times in its current state, should we really remove this one property and throw away all that review effort.
Quoted 4 lines
The OpenBSD driver already uses these properties. So even if the Linux driver doesn't use this yet, there is an existing implementation that does. That should be good enough for it to be included in the binding isn't it?
Yes, I suspected that might be the case too. I think it's fine.
Thanks Russel for the clarification btw. Feel free to add my
Kind regards,
Alvin
Re: [PATCH wireless-next v2 01/12] dt-bindings: net: bcm4329-fmac: Add Apple properties & chips
Quoted 99 lines · Alvin Šipraga
Hi both,
Quoted 91 lines · Mark Kettenis
Quoted 82 lines
Date: Mon, 12 Sep 2022 15:01:06 +0100
From: "Russell King (Oracle)" <[email protected]>Quoted 71 lines · Russell King (Oracle)
Quoted 59 lines · Alvin Šipraga
Quoted 58 lines · Russell King
From: Hector Martin <[email protected]>
This binding is currently used for SDIO devices, but these chips are also used as PCIe devices on DT platforms and may be represented in the DT. Re-use the existing binding and add chip compatibles used by Apple T2 and M1 platforms (the T2 ones are not known to be used in DT platforms, but we might as well document them).
Then, add properties required for firmware selection and calibration on M1 machines.
Reviewed-by Linus Walleij <[email protected]>Signed-off-by Hector Martin <[email protected]>Reviewed-by Mark Kettenis <[email protected]>Reviewed-by Rob Herring <[email protected]>Signed-off-by Russell King (Oracle) <[email protected]>--- .../net/wireless/brcm,bcm4329-fmac.yaml | 39 +++++++++++++++++-- 1 file changed, 35 insertions(+), 4 deletions(-)Documentation/devicetree/bindings/net/wireless/brcm,bcm4329-fmac.yaml +10
-4@@ -4,7 +4,7 @@ $id: http://devicetree.org/schemas/net/wireless/brcm,bcm4329-fmac.yaml $schema: http://devicetree.org/meta-schemas/core.yaml -title: Broadcom BCM4329 family fullmac wireless SDIO devices +title: Broadcom BCM4329 family fullmac wireless SDIO/PCIE devices maintainers: - Arend van Spriel <[email protected]>@@ -41,11 +41,17 @@ title: Broadcom BCM4329 family fullmac wireless SDIO devices - cypress,cyw4373-fmac - cypress,cyw43012-fmac - const: brcm,bcm4329-fmac - - const: brcm,bcm4329-fmac + - enum: + - brcm,bcm4329-fmac + - pci14e4,43dc # BCM4355 + - pci14e4,4464 # BCM4364 + - pci14e4,4488 # BCM4377 + - pci14e4,4425 # BCM4378 + - pci14e4,4433 # BCM4387 reg: - description: SDIO function number for the device, for most cases - this will be 1. + description: SDIO function number for the device (for most cases + this will be 1) or PCI device identifier. interrupts: maxItems: 1@@ -85,6 +91,31 @@ title: Broadcom BCM4329 family fullmac wireless SDIO devices takes precedence. type: booleanQuoted 10 lines
Documentation/devicetree/bindings/net/wireless/brcm,bcm4329-fmac.yaml title: Broadcom BCM4329 family fullmac wireless SDIO devices · line 98
Quoted 5 lines
Documentation/devicetree/bindings/net/wireless/brcm,bcm4329-fmac.yaml +5
-0+ brcm,cal-blob: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: A per-device calibration blob for the Wi-Fi radio. This + should be filled in by the bootloader from platform configuration + data, if necessary, and will be uploaded to the device if present.Is this a leftover from a previous revision of the patchset? Because as far as I can tell, the CLM blob is (still) being loaded via firmware, and no additional parsing has been added for this particular OF property. Should it be dropped?
Quoted 3 lines
It does appear to be unparsed, but I don't know whether it's needed for the binding or not. I'll wait for the Asahi folk to review your comment before possibly removing it.
Okay, the answer is, it is still very much part of the binding, and the m1n1 boot loader populates it.
Quoted 8 lines
This series is a subset of a larger series (remember the previous 34 or 35 patch series?), so there are things in the binding document which are not included in this series.
I don't think it makes sense to break up the binding document given that it has already been reviewed several times in its current state, should we really remove this one property and throw away all that review effort.
Quoted 4 lines
The OpenBSD driver already uses these properties. So even if the Linux driver doesn't use this yet, there is an existing implementation that does. That should be good enough for it to be included in the binding isn't it?
Quoted 5 lines
Yes, I suspected that might be the case too. I think it's fine.
Thanks Russel for the clarification btw. Feel free to add my
Reviewed-by Alvin Šipraga <[email protected]>
Thanks!
Signature · 2 lines
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/ FTTP is here! 40Mbps down 10Mbps up. Decent connectivity at last!
PATCH v2 2/12 brcmfmac: firmware: Handle per-board clm_blob files
In reply to Russell King (Oracle)From: Hector Martin <[email protected]>
Teach brcm_alt_fw_paths to correctly split off variable length extensions, and enable alt firmware lookups for the CLM blob firmware requests.
Apple platforms have per-board CLM blob files.
--- .../broadcom/brcm80211/brcmfmac/firmware.c | 33 +++++++++++-------- 1 file changed, 20 insertions(+), 13 deletions(-)
drivers/net/wireless/broadcom/brcm80211/brcmfmac/firmware.c +20 -13
@@ -587,22 +587,29 @@ static int brcmf_fw_complete_request(const struct firmware *fw,static char *brcm_alt_fw_path (const char *path,const char *board_type) { -char alt_path[BRCMF_FW_NAME_LEN ]; -char suffix[5 ]; +char base[BRCMF_FW_NAME_LEN ]; +const char *suffix; +char *ret; -strscpy (alt_path, path,BRCMF_FW_NAME_LEN ); -/* At least one character + suffix */ -if (strlen (alt_path) <5 ) +if (!board_type)return NULL ; -/* strip .txt or .bin at the end */ -strscpy (suffix, alt_path +strlen (alt_path) -4 ,5 ); - alt_path[strlen (alt_path) -4 ] =0 ; -strlcat (alt_path,"." ,BRCMF_FW_NAME_LEN ); -strlcat (alt_path, board_type,BRCMF_FW_NAME_LEN ); -strlcat (alt_path, suffix,BRCMF_FW_NAME_LEN ); + suffix =strrchr (path,'.' ); +if (!suffix || suffix == path) +return NULL ; + +/* strip extension at the end */ +strscpy (base, path,BRCMF_FW_NAME_LEN ); + base[suffix - path] =0 ; + + ret =kasprintf (GFP_KERNEL ,"%s.%s%s" , base, board_type, suffix); +if (!ret) +brcmf_err ("out of memory allocating firmware path for '%s'\n" , + path); + +brcmf_dbg (TRACE ,"FW alt path: %s\n" , ret); -return kstrdup (alt_path,GFP_KERNEL ); +return ret; } static int brcmf_fw_request_firmware(const struct firmware **fw,
@@ -612,7 +619,7 @@ static int brcmf_fw_request_firmware(const struct firmware **fw,int ret;/* Files can be board-specific, first try a board-specific path */ -if (cur->type ==BRCMF_FW_TYPE_NVRAM && fwctx->req->board_type) { +if (fwctx->req->board_type) {char *alt_path; alt_path =brcm_alt_fw_path (cur->path, fwctx->req->board_type);
Signature · 1 line
2.30.2
Re: [PATCH wireless-next v2 02/12] brcmfmac: firmware: Handle per-board clm_blob files
Quoted 6 lines · Russell King
From: Hector Martin <[email protected]>
Teach
brcm_alt_fw_pathsto correctly split off variable length extensions, and enable alt firmware lookups for the CLM blob firmware requests.
Quoted 7 lines
Apple platforms have per-board CLM blob files.
Acked-by Linus Walleij <[email protected]>Reviewed-by Arend van Spriel <[email protected]>Signed-off-by Hector Martin <[email protected]>Signed-off-by Russell King (Oracle) <[email protected]>---
PATCH v2 3/12 brcmfmac: pcie/sdio/usb: Get CLM blob via standard firmware mechanism
In reply to Russell King (Oracle)From: Hector Martin <[email protected]>
Now that the firmware fetcher can handle per-board CLM files, load the CLM blob alongside the other firmware files and change the bus API to just return the existing blob, instead of fetching the filename.
This enables per-board CLM blobs, which are required on Apple platforms.
--- .../broadcom/brcm80211/brcmfmac/bus.h | 19 ++++++--- .../broadcom/brcm80211/brcmfmac/common.c | 12 +----- .../broadcom/brcm80211/brcmfmac/pcie.c | 39 ++++++++++++------- .../broadcom/brcm80211/brcmfmac/sdio.c | 36 ++++++++++------- .../broadcom/brcm80211/brcmfmac/sdio.h | 2 + .../broadcom/brcm80211/brcmfmac/usb.c | 23 +++-------- 6 files changed, 69 insertions(+), 62 deletions(-)
drivers/net/wireless/broadcom/brcm80211/brcmfmac/bus.h +13 -6
@@ -6,6 +6,8 @@#ifndef BRCMFMAC_BUS_H #define BRCMFMAC_BUS_H +#include <linux/kernel.h> +#include <linux/firmware.h> #include "debug.h" /* IDs of the 6 default common rings of msgbuf protocol */
@@ -34,6 +36,11 @@ enum brcmf_bus_protocol_type {BRCMF_PROTO_MSGBUF }; +/* Firmware blobs that may be available */ +enum brcmf_blob_type { +BRCMF_BLOB_CLM , +}; +struct brcmf_mp_device ;struct brcmf_bus_dcmd {
@@ -60,7 +67,7 @@ struct brcmf_bus_dcmd {* @wowl_config: specify if dongle is configured for wowl when going to suspend * @get_ramsize: obtain size of device memory. * @get_memdump: obtain device memory dump in provided buffer. -* @get_fwname: obtain firmware name. +* @get_blob: obtain a firmware blob. * * This structure provides an abstract interface towards the * bus specific driver. For control messages to common driver
@@ -77,8 +84,8 @@ struct brcmf_bus_ops {void (*wowl_config)(struct device *dev,bool enabled);size_t (*get_ramsize)(struct device *dev);int (*get_memdump)(struct device *dev,void *data,size_t len); -int (*get_fwname)(struct device *dev,const char *ext, -unsigned char *fw_name); +int (*get_blob)(struct device *dev,const struct firmware **fw, +enum brcmf_blob_type type);void (*debugfs_create)(struct device *dev);int (*reset)(struct device *dev); };
@@ -220,10 +227,10 @@ int brcmf_bus_get_memdump(struct brcmf_bus *bus, void *data, size_t len) }static inline -int brcmf_bus_get_fwname (struct brcmf_bus *bus,const char *ext, -unsigned char *fw_name) +int brcmf_bus_get_blob (struct brcmf_bus *bus,const struct firmware **fw, +enum brcmf_blob_type type) { -return bus->ops->get_fwname (bus->dev, ext, fw_name); +return bus->ops->get_blob (bus->dev, fw, type); } static inline
drivers/net/wireless/broadcom/brcm80211/brcmfmac/common.c +2 -10
@@ -123,7 +123,6 @@ static int brcmf_c_process_clm_blob(struct brcmf_if *ifp)struct brcmf_bus *bus = drvr->bus_if;struct brcmf_dload_data_le *chunk_buf;const struct firmware *clm =NULL ; -u8 clm_name[BRCMF_FW_NAME_LEN ];u32 chunk_len;u32 datalen;u32 cumulative_len;
@@ -133,15 +132,8 @@ static int brcmf_c_process_clm_blob(struct brcmf_if *ifp)brcmf_dbg (TRACE ,"Enter\n" ); -memset (clm_name,0 ,sizeof (clm_name)); - err =brcmf_bus_get_fwname (bus,".clm_blob" , clm_name); -if (err) { -bphy_err (drvr,"get CLM blob file name failed (%d)\n" , err); -return err; - } - - err =firmware_request_nowarn (&clm, clm_name, bus->dev); -if (err) { + err =brcmf_bus_get_blob (bus, &clm,BRCMF_BLOB_CLM ); +if (err || !clm) {brcmf_info ("no clm_blob available (err=%d), device may have limited channels available\n" , err);return 0 ;
drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c +25 -14
@@ -66,6 +66,7 @@ MODULE_FIRMWARE(BRCMF_FW_DEFAULT_PATH "brcmfmac*-pcie.*.txt");/* per-board firmware binaries */ MODULE_FIRMWARE (BRCMF_FW_DEFAULT_PATH "brcmfmac*-pcie.*.bin" ); +MODULE_FIRMWARE (BRCMF_FW_DEFAULT_PATH "brcmfmac*-pcie.*.clm_blob" );static const struct brcmf_firmware_mapping brcmf_pcie_fwnames[] = {BRCMF_FW_ENTRY (BRCM_CC_43602_CHIP_ID ,0xFFFFFFFF ,43602 ),
@@ -261,6 +262,8 @@ struct brcmf_pciedev_info {struct pci_dev *pdev;char fw_name[BRCMF_FW_NAME_LEN ];char nvram_name[BRCMF_FW_NAME_LEN ]; +char clm_name[BRCMF_FW_NAME_LEN ]; +const struct firmware *clm_fw;void __iomem *regs;void __iomem *tcm;u32 ram_base;
@@ -1382,23 +1385,25 @@ static int brcmf_pcie_get_memdump(struct device *dev, void *data, size_t len)return 0 ; } -static -int brcmf_pcie_get_fwname (struct device *dev,const char *ext,u8 *fw_name) +static int brcmf_pcie_get_blob (struct device *dev,const struct firmware **fw, +enum brcmf_blob_type type) {struct brcmf_bus *bus_if =dev_get_drvdata (dev); -struct brcmf_fw_request *fwreq; -struct brcmf_fw_name fwnames[] = { - { ext, fw_name }, - }; +struct brcmf_pciedev *buspub = bus_if->bus_priv.pcie; +struct brcmf_pciedev_info *devinfo = buspub->devinfo; - fwreq =brcmf_fw_alloc_request (bus_if->chip, bus_if->chiprev, - brcmf_pcie_fwnames, -ARRAY_SIZE (brcmf_pcie_fwnames), - fwnames,ARRAY_SIZE (fwnames)); -if (!fwreq) -return -ENOMEM ; +switch (type) { +case BRCMF_BLOB_CLM : + *fw = devinfo->clm_fw; + devinfo->clm_fw =NULL ; +break ; +default : +return -ENOENT ; + } + +if (!*fw) +return -ENOENT ; -kfree (fwreq);return 0 ; }
@@ -1445,7 +1450,7 @@ static const struct brcmf_bus_ops brcmf_pcie_bus_ops = { .wowl_config = brcmf_pcie_wowl_config, .get_ramsize = brcmf_pcie_get_ramsize, .get_memdump = brcmf_pcie_get_memdump, - .get_fwname = brcmf_pcie_get_fwname, + .get_blob = brcmf_pcie_get_blob, .reset = brcmf_pcie_reset, };
@@ -1731,6 +1736,7 @@ static const struct brcmf_buscore_ops brcmf_pcie_buscore_ops = {#define BRCMF_PCIE_FW_CODE 0#define BRCMF_PCIE_FW_NVRAM 1 +#define BRCMF_PCIE_FW_CLM 2static void brcmf_pcie_setup (struct device *dev,int ret,struct brcmf_fw_request *fwreq)
@@ -1755,6 +1761,7 @@ static void brcmf_pcie_setup(struct device *dev, int ret, fw = fwreq->items[BRCMF_PCIE_FW_CODE ].binary; nvram = fwreq->items[BRCMF_PCIE_FW_NVRAM ].nv_data.data; nvram_len = fwreq->items[BRCMF_PCIE_FW_NVRAM ].nv_data.len; + devinfo->clm_fw = fwreq->items[BRCMF_PCIE_FW_CLM ].binary;kfree (fwreq); ret =brcmf_chip_get_raminfo (devinfo->ci);
@@ -1830,6 +1837,7 @@ brcmf_pcie_prepare_fw_request(struct brcmf_pciedev_info *devinfo)struct brcmf_fw_name fwnames[] = { {".bin" , devinfo->fw_name }, {".txt" , devinfo->nvram_name }, + {".clm_blob" , devinfo->clm_name }, }; fwreq = brcmf_fw_alloc_request(devinfo->ci->chip, devinfo->ci->chiprev,
@@ -1842,6 +1850,8 @@ brcmf_pcie_prepare_fw_request(struct brcmf_pciedev_info *devinfo) fwreq->items[BRCMF_PCIE_FW_CODE ].type =BRCMF_FW_TYPE_BINARY ; fwreq->items[BRCMF_PCIE_FW_NVRAM ].type =BRCMF_FW_TYPE_NVRAM ; fwreq->items[BRCMF_PCIE_FW_NVRAM ].flags =BRCMF_FW_REQF_OPTIONAL ; + fwreq->items[BRCMF_PCIE_FW_CLM ].type =BRCMF_FW_TYPE_BINARY ; + fwreq->items[BRCMF_PCIE_FW_CLM ].flags =BRCMF_FW_REQF_OPTIONAL ; fwreq->board_type = devinfo->settings->board_type;/* NVRAM reserves PCI domain 0 for Broadcom's SDK faked bus */ fwreq->domain_nr =pci_domain_nr (devinfo->pdev->bus) +1 ;
@@ -1981,6 +1991,7 @@ brcmf_pcie_remove(struct pci_dev *pdev)brcmf_pcie_release_ringbuffers (devinfo);brcmf_pcie_reset_device (devinfo);brcmf_pcie_release_resource (devinfo); +release_firmware (devinfo->clm_fw);if (devinfo->ci)brcmf_chip_detach (devinfo->ci);
drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c +22 -14
@@ -4131,23 +4131,24 @@ brcmf_sdio_watchdog(struct timer_list *t) } } -static -int brcmf_sdio_get_fwname (struct device *dev,const char *ext,u8 *fw_name) +static int brcmf_sdio_get_blob (struct device *dev,const struct firmware **fw, +enum brcmf_blob_type type) {struct brcmf_bus *bus_if =dev_get_drvdata (dev); -struct brcmf_fw_request *fwreq; -struct brcmf_fw_name fwnames[] = { - { ext, fw_name }, - }; +struct brcmf_sdio_dev *sdiodev = bus_if->bus_priv.sdio; - fwreq =brcmf_fw_alloc_request (bus_if->chip, bus_if->chiprev, - brcmf_sdio_fwnames, -ARRAY_SIZE (brcmf_sdio_fwnames), - fwnames,ARRAY_SIZE (fwnames)); -if (!fwreq) -return -ENOMEM ; +switch (type) { +case BRCMF_BLOB_CLM : + *fw = sdiodev->clm_fw; + sdiodev->clm_fw =NULL ; +break ; +default : +return -ENOENT ; + } + +if (!*fw) +return -ENOENT ; -kfree (fwreq);return 0 ; }
@@ -4182,13 +4183,14 @@ static const struct brcmf_bus_ops brcmf_sdio_bus_ops = { .wowl_config = brcmf_sdio_wowl_config, .get_ramsize = brcmf_sdio_bus_get_ramsize, .get_memdump = brcmf_sdio_bus_get_memdump, - .get_fwname = brcmf_sdio_get_fwname, + .get_blob = brcmf_sdio_get_blob, .debugfs_create = brcmf_sdio_debugfs_create, .reset = brcmf_sdio_bus_reset };#define BRCMF_SDIO_FW_CODE 0#define BRCMF_SDIO_FW_NVRAM 1 +#define BRCMF_SDIO_FW_CLM 2static void brcmf_sdio_firmware_callback (struct device *dev,int err,struct brcmf_fw_request *fwreq)
@@ -4211,6 +4213,7 @@ static void brcmf_sdio_firmware_callback(struct device *dev, int err, code = fwreq->items[BRCMF_SDIO_FW_CODE ].binary; nvram = fwreq->items[BRCMF_SDIO_FW_NVRAM ].nv_data.data; nvram_len = fwreq->items[BRCMF_SDIO_FW_NVRAM ].nv_data.len; + sdiod->clm_fw = fwreq->items[BRCMF_SDIO_FW_CLM ].binary;kfree (fwreq);/* try to download image and nvram to the dongle */
@@ -4409,6 +4412,7 @@ brcmf_sdio_prepare_fw_request(struct brcmf_sdio *bus)struct brcmf_fw_name fwnames[] = { {".bin" , bus->sdiodev->fw_name }, {".txt" , bus->sdiodev->nvram_name }, + {".clm_blob" , bus->sdiodev->clm_name }, }; fwreq = brcmf_fw_alloc_request(bus->ci->chip, bus->ci->chiprev,
@@ -4420,6 +4424,8 @@ brcmf_sdio_prepare_fw_request(struct brcmf_sdio *bus) fwreq->items[BRCMF_SDIO_FW_CODE ].type =BRCMF_FW_TYPE_BINARY ; fwreq->items[BRCMF_SDIO_FW_NVRAM ].type =BRCMF_FW_TYPE_NVRAM ; + fwreq->items[BRCMF_SDIO_FW_CLM ].type =BRCMF_FW_TYPE_BINARY ; + fwreq->items[BRCMF_SDIO_FW_CLM ].flags =BRCMF_FW_REQF_OPTIONAL ; fwreq->board_type = bus->sdiodev->settings->board_type;return fwreq;
@@ -4576,6 +4582,8 @@ void brcmf_sdio_remove(struct brcmf_sdio *bus)if (bus->sdiodev->settings)brcmf_release_module_param (bus->sdiodev->settings); +release_firmware (bus->sdiodev->clm_fw); + bus->sdiodev->clm_fw =NULL ;kfree (bus->rxbuf);kfree (bus->hdrbuf);kfree (bus);
drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.h +2 -0
@@ -186,9 +186,11 @@ struct brcmf_sdio_dev {struct sg_table sgtable;char fw_name[BRCMF_FW_NAME_LEN ];char nvram_name[BRCMF_FW_NAME_LEN ]; +char clm_name[BRCMF_FW_NAME_LEN ];bool wowl_enabled;enum brcmf_sdiod_state state;struct brcmf_sdiod_freezer *freezer; +const struct firmware *clm_fw; };/* sdio core registers */
drivers/net/wireless/broadcom/brcm80211/brcmfmac/usb.c +5 -18
@@ -1154,24 +1154,11 @@ struct brcmf_usbdev *brcmf_usb_attach(struct brcmf_usbdev_info *devinfo,return NULL ; } -static -int brcmf_usb_get_fwname (struct device *dev,const char *ext,u8 *fw_name) +static int brcmf_usb_get_blob (struct device *dev,const struct firmware **fw, +enum brcmf_blob_type type) { -struct brcmf_bus *bus =dev_get_drvdata (dev); -struct brcmf_fw_request *fwreq; -struct brcmf_fw_name fwnames[] = { - { ext, fw_name }, - }; - - fwreq =brcmf_fw_alloc_request (bus->chip, bus->chiprev, - brcmf_usb_fwnames, -ARRAY_SIZE (brcmf_usb_fwnames), - fwnames,ARRAY_SIZE (fwnames)); -if (!fwreq) -return -ENOMEM ; - -kfree (fwreq); -return 0 ; +/* No blobs for USB devices... */ +return -ENOENT ; }static const struct brcmf_bus_ops brcmf_usb_bus_ops = {
@@ -1180,7 +1167,7 @@ static const struct brcmf_bus_ops brcmf_usb_bus_ops = { .txdata = brcmf_usb_tx, .txctl = brcmf_usb_tx_ctlpkt, .rxctl = brcmf_usb_rx_ctlpkt, - .get_fwname = brcmf_usb_get_fwname, + .get_blob = brcmf_usb_get_blob, };#define BRCMF_USB_FW_CODE 0
Signature · 1 line
2.30.2
Re: [PATCH wireless-next v2 03/12] brcmfmac: pcie/sdio/usb: Get CLM blob via standard firmware mechanism
Quoted 6 lines · Russell King
From: Hector Martin <[email protected]>
Now that the firmware fetcher can handle per-board CLM files, load the CLM blob alongside the other firmware files and change the bus API to just return the existing blob, instead of fetching the filename.
Quoted 7 lines
This enables per-board CLM blobs, which are required on Apple platforms.
Acked-by Linus Walleij <[email protected]>Reviewed-by Arend van Spriel <[email protected]>Signed-off-by Hector Martin <[email protected]>Signed-off-by Russell King (Oracle) <[email protected]>---
PATCH v2 4/12 brcmfmac: firmware: Support passing in multiple board_types
In reply to Russell King (Oracle)From: Hector Martin <[email protected]>
Apple platforms have firmware and config files identified with multiple dimensions. We want to be able to find the most specific firmware available for any given platform, progressively trying more general firmwares.
To do this, first add support for passing in multiple board_types, which will be tried in sequence.
Since this will cause more log spam due to missing firmwares, also switch the secondary firmware fecthes to use the _nowarn variant, which will not log if the firmware is not found.
--- .../broadcom/brcm80211/brcmfmac/firmware.c | 53 +++++++++++++++---- .../broadcom/brcm80211/brcmfmac/firmware.h | 4 +- .../broadcom/brcm80211/brcmfmac/pcie.c | 4 +- .../broadcom/brcm80211/brcmfmac/sdio.c | 2 +- 4 files changed, 49 insertions(+), 14 deletions(-)
drivers/net/wireless/broadcom/brcm80211/brcmfmac/firmware.c +42 -11
@@ -430,6 +430,7 @@ struct brcmf_fw {struct device *dev;struct brcmf_fw_request *req;u32 curpos; +unsigned int board_index;void (*done)(struct device *dev,int err,struct brcmf_fw_request *req); };
@@ -616,17 +617,21 @@ static int brcmf_fw_request_firmware(const struct firmware **fw, struct brcmf_fw *fwctx) {struct brcmf_fw_item *cur = &fwctx->req->items[fwctx->curpos]; +unsigned int i;int ret; -/* Files can be board-specific, first try a board-specific path */ -if (fwctx->req->board_type) { +/* Files can be board-specific, first try board-specific paths */ +for (i =0 ; i <ARRAY_SIZE (fwctx->req->board_types); i++) {char *alt_path; - alt_path =brcm_alt_fw_path (cur->path, fwctx->req->board_type); +if (!fwctx->req->board_types[i]) + goto fallback; + alt_path =brcm_alt_fw_path (cur->path, + fwctx->req->board_types[i]);if (!alt_path) goto fallback; - ret =request_firmware (fw, alt_path, fwctx->dev); + ret =firmware_request_nowarn (fw, alt_path, fwctx->dev);kfree (alt_path);if (ret ==0 )return ret;
@@ -660,15 +665,40 @@ static void brcmf_fw_request_done_alt_path(const struct firmware *fw, void *ctx) {struct brcmf_fw *fwctx = ctx;struct brcmf_fw_item *first = &fwctx->req->items[0 ]; +const char *board_type, *alt_path;int ret =0 ; -/* Fall back to canonical path if board firmware not found */ -if (!fw) - ret =request_firmware_nowait (THIS_MODULE , true, first->path, +if (fw) { +brcmf_fw_request_done (fw, ctx); +return ; + } + +/* Try next board firmware */ +if (fwctx->board_index <ARRAY_SIZE (fwctx->req->board_types)) { + board_type = fwctx->req->board_types[fwctx->board_index++]; +if (!board_type) + goto fallback; + alt_path =brcm_alt_fw_path (first->path, board_type); +if (!alt_path) + goto fallback; + + ret =request_firmware_nowait (THIS_MODULE , true, alt_path, fwctx->dev,GFP_KERNEL , fwctx, - brcmf_fw_request_done); + brcmf_fw_request_done_alt_path); +kfree (alt_path); -if (fw || ret <0 ) +if (ret <0 ) +brcmf_fw_request_done (fw, ctx); +return ; + } + +fallback: +/* Fall back to canonical path if board firmware not found */ + ret =request_firmware_nowait (THIS_MODULE , true, first->path, + fwctx->dev,GFP_KERNEL , fwctx, + brcmf_fw_request_done); + +if (ret <0 )brcmf_fw_request_done (fw, ctx); }
@@ -712,10 +742,11 @@ int brcmf_fw_get_firmwares(struct device *dev, struct brcmf_fw_request *req, fwctx->done = fw_cb;/* First try alternative board-specific path if any */ -if (fwctx->req->board_type) +if (fwctx->req->board_types[0 ]) alt_path =brcm_alt_fw_path (first->path, - fwctx->req->board_type); + fwctx->req->board_types[0 ]);if (alt_path) { + fwctx->board_index++; ret =request_firmware_nowait (THIS_MODULE , true, alt_path, fwctx->dev,GFP_KERNEL , fwctx, brcmf_fw_request_done_alt_path);
drivers/net/wireless/broadcom/brcm80211/brcmfmac/firmware.h +3 -1
@@ -11,6 +11,8 @@#define BRCMF_FW_DEFAULT_PATH "brcm/" +#define BRCMF_FW_MAX_BOARD_TYPES 8 +/** * struct brcmf_firmware_mapping - Used to map chipid/revmask to firmware * filename and nvram filename. Each bus type implementation should create
@@ -66,7 +68,7 @@ struct brcmf_fw_request {u16 domain_nr;u16 bus_nr;u32 n_items; -const char *board_type; +const char *board_types[BRCMF_FW_MAX_BOARD_TYPES ];struct brcmf_fw_item items[]; };
drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c +3 -1
@@ -1852,11 +1852,13 @@ brcmf_pcie_prepare_fw_request(struct brcmf_pciedev_info *devinfo) fwreq->items[BRCMF_PCIE_FW_NVRAM ].flags =BRCMF_FW_REQF_OPTIONAL ; fwreq->items[BRCMF_PCIE_FW_CLM ].type =BRCMF_FW_TYPE_BINARY ; fwreq->items[BRCMF_PCIE_FW_CLM ].flags =BRCMF_FW_REQF_OPTIONAL ; - fwreq->board_type = devinfo->settings->board_type;/* NVRAM reserves PCI domain 0 for Broadcom's SDK faked bus */ fwreq->domain_nr =pci_domain_nr (devinfo->pdev->bus) +1 ; fwreq->bus_nr = devinfo->pdev->bus->number; +brcmf_dbg (PCIE ,"Board: %s\n" , devinfo->settings->board_type); + fwreq->board_types[0 ] = devinfo->settings->board_type; +return fwreq; }
drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c +1 -1
@@ -4426,7 +4426,7 @@ brcmf_sdio_prepare_fw_request(struct brcmf_sdio *bus) fwreq->items[BRCMF_SDIO_FW_NVRAM ].type =BRCMF_FW_TYPE_NVRAM ; fwreq->items[BRCMF_SDIO_FW_CLM ].type =BRCMF_FW_TYPE_BINARY ; fwreq->items[BRCMF_SDIO_FW_CLM ].flags =BRCMF_FW_REQF_OPTIONAL ; - fwreq->board_type = bus->sdiodev->settings->board_type; + fwreq->board_types[0 ] = bus->sdiodev->settings->board_type;return fwreq; }
Signature · 1 line
2.30.2
Re: [PATCH wireless-next v2 04/12] brcmfmac: firmware: Support passing in multiple board_types
Quoted 10 lines · Russell King
From: Hector Martin <[email protected]>
Apple platforms have firmware and config files identified with multiple dimensions. We want to be able to find the most specific firmware available for any given platform, progressively trying more general firmwares.
To do this, first add support for passing in multiple
board_types, which will be tried in sequence.
Quoted 7 lines
Since this will cause more log spam due to missing firmwares, also switch the secondary firmware fecthes to use the
_nowarnvariant, which will not log if the firmware is not found.Signed-off-by Hector Martin <[email protected]>Signed-off-by Russell King (Oracle) <[email protected]>---
PATCH v2 5/12 brcmfmac: pcie: Read Apple OTP information
In reply to Russell King (Oracle)From: Hector Martin <[email protected]>
On Apple platforms, the One Time Programmable ROM in the Broadcom chips contains information about the specific board design (module, vendor, version) that is required to select the correct NVRAM file. Parse this OTP ROM and extract the required strings.
Note that the user OTP offset/size is per-chip. This patch does not add any chips yet.
--- .../broadcom/brcm80211/brcmfmac/pcie.c | 218 ++++++++++++++++++ include/linux/bcma/bcma_driver_chipcommon.h | 1 + 2 files changed, 219 insertions(+)
drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c +218 -0
@@ -256,6 +256,15 @@ struct brcmf_pcie_core_info {u32 wrapbase; }; +#define BRCMF_OTP_MAX_PARAM_LEN 16 + +struct brcmf_otp_params { +char module[BRCMF_OTP_MAX_PARAM_LEN ]; +char vendor[BRCMF_OTP_MAX_PARAM_LEN ]; +char version[BRCMF_OTP_MAX_PARAM_LEN ]; +bool valid; +}; +struct brcmf_pciedev_info {enum brcmf_pcie_state state;bool in_irq;
@@ -283,6 +292,7 @@ struct brcmf_pciedev_info {void (*write_ptr)(struct brcmf_pciedev_info *devinfo,u32 mem_offset,u16 value);struct brcmf_mp_device *settings; +struct brcmf_otp_params otp; };struct brcmf_pcie_ringbuf {
@@ -354,6 +364,14 @@ static void brcmf_pcie_setup(struct device *dev, int ret,static struct brcmf_fw_request *brcmf_pcie_prepare_fw_request (struct brcmf_pciedev_info *devinfo); +static u16 +brcmf_pcie_read_reg16 (struct brcmf_pciedev_info *devinfo,u32 reg_offset) +{ +void __iomem *address = devinfo->regs + reg_offset; + +return ioread16 (address); +} +static u32 brcmf_pcie_read_reg32 (struct brcmf_pciedev_info *devinfo,u32 reg_offset) {
@@ -499,6 +517,8 @@ brcmf_pcie_copy_dev_tomem(struct brcmf_pciedev_info *devinfo, u32 mem_offset, } +#define READCC32 (devinfo, reg) brcmf_pcie_read_reg32(devinfo, \ + CHIPCREGOFFS(reg))#define WRITECC32 (devinfo, reg, value) brcmf_pcie_write_reg32(devinfo, \ CHIPCREGOFFS(reg), value)
@@ -1734,6 +1754,198 @@ static const struct brcmf_buscore_ops brcmf_pcie_buscore_ops = { .write32 = brcmf_pcie_buscore_write32, }; +#define BRCMF_OTP_SYS_VENDOR 0x15 +#define BRCMF_OTP_BRCM_CIS 0x80 + +#define BRCMF_OTP_VENDOR_HDR 0x00000008 + +static int +brcmf_pcie_parse_otp_sys_vendor (struct brcmf_pciedev_info *devinfo, +u8 *data,size_t size) +{ +int idx =4 ; +const char *chip_params; +const char *board_params; +const char *p; + +/* 4-byte header and two empty strings */ +if (size <6 ) +return -EINVAL ; + +if (get_unaligned_le32 (data) !=BRCMF_OTP_VENDOR_HDR ) +return -EINVAL ; + + chip_params = &data[idx]; + +/* Skip first string, including terminator */ + idx +=strnlen (chip_params, size - idx) +1 ; +if (idx >= size) +return -EINVAL ; + + board_params = &data[idx]; + +/* Skip to terminator of second string */ + idx +=strnlen (board_params, size - idx); +if (idx >= size) +return -EINVAL ; + +/* At this point both strings are guaranteed NUL-terminated */ +brcmf_dbg (PCIE ,"OTP: chip_params='%s' board_params='%s'\n" , + chip_params, board_params); + + p =skip_spaces (board_params); +while (*p) { +char tag = *p++; +const char *end; +size_t len; + +if (*p++ !='=' )/* implicit NUL check */ +return -EINVAL ; + +/* *p might be NUL here, if so end == p and len == 0 */ + end =strchrnul (p,' ' ); + len = end - p; + +/* leave 1 byte for NUL in destination string */ +if (len > (BRCMF_OTP_MAX_PARAM_LEN -1 )) +return -EINVAL ; + +/* Copy len characters plus a NUL terminator */ +switch (tag) { +case 'M' : +strscpy (devinfo->otp.module, p, len +1 ); +break ; +case 'V' : +strscpy (devinfo->otp.vendor, p, len +1 ); +break ; +case 'm' : +strscpy (devinfo->otp.version, p, len +1 ); +break ; + } + +/* Skip to next arg, if any */ + p =skip_spaces (end); + } + +brcmf_dbg (PCIE ,"OTP: module=%s vendor=%s version=%s\n" , + devinfo->otp.module, devinfo->otp.vendor, + devinfo->otp.version); + +if (!devinfo->otp.module[0 ] || + !devinfo->otp.vendor[0 ] || + !devinfo->otp.version[0 ]) +return -EINVAL ; + + devinfo->otp.valid = true; +return 0 ; +} + +static int +brcmf_pcie_parse_otp (struct brcmf_pciedev_info *devinfo,u8 *otp,size_t size) +{ +int p =0 ; +int ret = -EINVAL ; + +brcmf_dbg (PCIE ,"parse_otp size=%zd\n" , size); + +while (p < (size -1 )) { +u8 type = otp[p]; +u8 length = otp[p +1 ]; + +if (type ==0 ) +break ; + +if ((p +2 + length) > size) +break ; + +switch (type) { +case BRCMF_OTP_SYS_VENDOR : +brcmf_dbg (PCIE ,"OTP @ 0x%x (%d): SYS_VENDOR\n" , + p, length); + ret =brcmf_pcie_parse_otp_sys_vendor (devinfo, + &otp[p +2 ], + length); +break ; +case BRCMF_OTP_BRCM_CIS : +brcmf_dbg (PCIE ,"OTP @ 0x%x (%d): BRCM_CIS\n" , + p, length); +break ; +default : +brcmf_dbg (PCIE ,"OTP @ 0x%x (%d): Unknown type 0x%x\n" , + p, length, type); +break ; + } + + p +=2 + length; + } + +return ret; +} + +static int brcmf_pcie_read_otp (struct brcmf_pciedev_info *devinfo) +{ +const struct pci_dev *pdev = devinfo->pdev; +struct brcmf_bus *bus =dev_get_drvdata (&pdev->dev); +u32 coreid, base, words, idx, sromctl; +u16 *otp; +struct brcmf_core *core; +int ret; + +switch (devinfo->ci->chip) { +default : +/* OTP not supported on this chip */ +return 0 ; + } + + core =brcmf_chip_get_core (devinfo->ci, coreid); +if (!core) { +brcmf_err (bus,"No OTP core\n" ); +return -ENODEV ; + } + +if (coreid ==BCMA_CORE_CHIPCOMMON ) { +/* Chips with OTP accessed via ChipCommon need additional +* handling to access the OTP +*/ +brcmf_pcie_select_core (devinfo, coreid); + sromctl =READCC32 (devinfo, sromcontrol); + +if (!(sromctl &BCMA_CC_SROM_CONTROL_OTP_PRESENT )) { +/* Chip lacks OTP, try without it... */ +brcmf_err (bus, +"OTP unavailable, using default firmware\n" ); +return 0 ; + } + +/* Map OTP to shadow area */ +WRITECC32 (devinfo, sromcontrol, + sromctl |BCMA_CC_SROM_CONTROL_OTPSEL ); + } + + otp =kcalloc (words,sizeof (u16),GFP_KERNEL ); +if (!otp) +return -ENOMEM ; + +/* Map bus window to SROM/OTP shadow area in core */ + base =brcmf_pcie_buscore_prep_addr (devinfo->pdev, base + core->base); + +brcmf_dbg (PCIE ,"OTP data:\n" ); +for (idx =0 ; idx < words; idx++) { + otp[idx] =brcmf_pcie_read_reg16 (devinfo, base +2 * idx); +brcmf_dbg (PCIE ,"[%8x] 0x%04x\n" , base +2 * idx, otp[idx]); + } + +if (coreid ==BCMA_CORE_CHIPCOMMON ) { +brcmf_pcie_select_core (devinfo, coreid); +WRITECC32 (devinfo, sromcontrol, sromctl); + } + + ret =brcmf_pcie_parse_otp (devinfo, (u8 *)otp,2 * words); +kfree (otp); + +return ret; +} +#define BRCMF_PCIE_FW_CODE 0#define BRCMF_PCIE_FW_NVRAM 1#define BRCMF_PCIE_FW_CLM 2
@@ -1930,6 +2142,12 @@ brcmf_pcie_probe(struct pci_dev *pdev, const struct pci_device_id *id)if (ret) goto fail_bus; + ret =brcmf_pcie_read_otp (devinfo); +if (ret) { +brcmf_err (bus,"failed to parse OTP\n" ); + goto fail_brcmf; + } + fwreq =brcmf_pcie_prepare_fw_request (devinfo);if (!fwreq) { ret = -ENOMEM ;
include/linux/bcma/bcma_driver_chipcommon.h +1 -0
@@ -271,6 +271,7 @@#define BCMA_CC_SROM_CONTROL_OP_WRDIS 0x40000000#define BCMA_CC_SROM_CONTROL_OP_WREN 0x60000000#define BCMA_CC_SROM_CONTROL_OTPSEL 0x00000010 +#define BCMA_CC_SROM_CONTROL_OTP_PRESENT 0x00000020#define BCMA_CC_SROM_CONTROL_LOCK 0x00000008#define BCMA_CC_SROM_CONTROL_SIZE_MASK 0x00000006#define BCMA_CC_SROM_CONTROL_SIZE_1K 0x00000000
Signature · 1 line
2.30.2
PATCH v2 6/12 brcmfmac: of: Fetch Apple properties
In reply to Russell King (Oracle)From: Hector Martin <[email protected]>
On Apple ARM64 platforms, firmware selection requires two properties that come from system firmware: the module-instance (aka "island", a codename representing a given hardware platform) and the antenna-sku. We map Apple's module codenames to board_types in the form "apple,<module-instance>".
The mapped board_type is added to the DTS file in that form, while the antenna-sku is forwarded by our bootloader from the Apple Device Tree into the FDT. Grab them from the DT so firmware selection can use them.
--- .../wireless/broadcom/brcm80211/brcmfmac/common.h | 1 + .../net/wireless/broadcom/brcm80211/brcmfmac/of.c | 12 +++++++++++- 2 files changed, 12 insertions(+), 1 deletion(-)
drivers/net/wireless/broadcom/brcm80211/brcmfmac/common.h +1 -0
@@ -53,6 +53,7 @@ struct brcmf_mp_device {struct brcmfmac_pd_cc *country_codes;const char *board_type;unsigned char mac[ETH_ALEN ]; +const char *antenna_sku;union {struct brcmfmac_sdio_pd sdio; } bus;
drivers/net/wireless/broadcom/brcm80211/brcmfmac/of.c +11 -1
@@ -70,14 +70,24 @@ void brcmf_of_probe(struct device *dev, enum brcmf_bus_type bus_type, {struct brcmfmac_sdio_pd *sdio = &settings->bus.sdio;struct device_node *root, *np = dev->of_node; +const char *prop;int irq;int err;u32 irqf;u32 val; +/* Apple ARM64 platforms have their own idea of board type, passed in +* via the device tree. They also have an antenna SKU parameter +*/ +if (!of_property_read_string (np,"brcm,board-type" , &prop)) + settings->board_type = prop; + +if (!of_property_read_string (np,"apple,antenna-sku" , &prop)) + settings->antenna_sku = prop; +/* Set board-type to the first string of the machine compatible prop */ root =of_find_node_by_path ("/" ); -if (root) { +if (root && !settings->board_type) {char *board_type;const char *tmp;
Signature · 1 line
2.30.2
Re: [PATCH wireless-next v2 06/12] brcmfmac: of: Fetch Apple properties
Quoted 13 lines · Russell King
From: Hector Martin <[email protected]>
On Apple ARM64 platforms, firmware selection requires two properties that come from system firmware: the module-instance (aka "island", a codename representing a given hardware platform) and the antenna-sku. We map Apple's module codenames to
board_typesin the form "apple,<module-instance>".The mapped
board_typeis added to the DTS file in that form, while the antenna-sku is forwarded by our bootloader from the Apple Device Tree into the FDT. Grab them from the DT so firmware selection can use them.
Quoted 4 lines
Reviewed-by Linus Walleij <[email protected]>Signed-off-by Hector Martin <[email protected]>Signed-off-by Russell King (Oracle) <[email protected]>---
PATCH v2 7/12 brcmfmac: pcie: Perform firmware selection for Apple platforms
In reply to Russell King (Oracle)From: Hector Martin <[email protected]>
On Apple platforms, firmware selection uses the following elements:
Property Example Source ============== ======= ======================== * Chip name 4378 Device ID * Chip revision B1 OTP * Platform shikoku DT (ARM64) or ACPI (x86) * Module type RASP OTP * Module vendor m OTP * Module version 6.11 OTP * Antenna SKU X3 DT (ARM64) or ACPI (x86)
In macOS, these firmwares are stored using filenames in this format under /usr/share/firmware/wifi:
C-4378__s-B1/P-shikoku-X3_M-RASP_V-m__m-6.11.txt
To prepare firmwares for Linux, we rename these to a scheme following the existing brcmfmac convention:
brcmfmac<chip><lower(rev)>-pcie.apple,<platform>-<mod_type>-\ <mod_vendor>-<mod_version>-<antenna_sku>.txt
The NVRAM uses all the components, while the firmware and CLM blob only use the chip/revision/platform/antenna_sku:
brcmfmac<chip><lower(rev)>-pcie.apple,<platform>-<antenna_sku>.bin
e.g.
brcm/brcmfmac4378b1-pcie.apple,shikoku-RASP-m-6.11-X3.txt
brcm/brcmfmac4378b1-pcie.apple,shikoku-X3.binIn addition, since there are over 1000 files in total, many of which are symlinks or outright duplicates, we deduplicate and prune the firmware tree to reduce firmware filenames to fewer dimensions. For example, the shikoku platform (MacBook Air M1 2020) simplifies to just 4 files:
brcm/brcmfmac4378b1-pcie.apple,shikoku.clm_blob brcm/brcmfmac4378b1-pcie.apple,shikoku.bin brcm/brcmfmac4378b1-pcie.apple,shikoku-RASP-m.txt brcm/brcmfmac4378b1-pcie.apple,shikoku-RASP-u.txt
This reduces the total file count to around 170, of which 75 are symlinks and 95 are regular files: 7 firmware blobs, 27 CLM blobs, and 61 NVRAM config files. We also slightly process NVRAM files to correct some formatting issues.
To handle this, the driver must try the following path formats when looking for firmware files:
brcm/brcmfmac4378b1-pcie.apple,shikoku-RASP-m-6.11-X3.txt
brcm/brcmfmac4378b1-pcie.apple,shikoku-RASP-m-6.11.txt
brcm/brcmfmac4378b1-pcie.apple,shikoku-RASP-m.txt
brcm/brcmfmac4378b1-pcie.apple,shikoku-RASP.txt
brcm/brcmfmac4378b1-pcie.apple,shikoku-X3.txt *
brcm/brcmfmac4378b1-pcie.apple,shikoku.txt* Not relevant for NVRAM, only for firmware/CLM.
The chip revision nominally comes from OTP on Apple platforms, but it can be mapped to the PCI revision number, so we ignore the OTP revision and continue to use the existing PCI revision mechanism to identify chip revisions, as the driver already does for other chips. Unfortunately, the mapping is not consistent between different chip types, so this has to be determined experimentally.
--- .../broadcom/brcm80211/brcmfmac/pcie.c | 41 ++++++++++++++++++- 1 file changed, 39 insertions(+), 2 deletions(-)
drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c +39 -2
@@ -2068,8 +2068,45 @@ brcmf_pcie_prepare_fw_request(struct brcmf_pciedev_info *devinfo) fwreq->domain_nr =pci_domain_nr (devinfo->pdev->bus) +1 ; fwreq->bus_nr = devinfo->pdev->bus->number; -brcmf_dbg (PCIE ,"Board: %s\n" , devinfo->settings->board_type); - fwreq->board_types[0 ] = devinfo->settings->board_type; +/* Apple platforms with fancy firmware/NVRAM selection */ +if (devinfo->settings->board_type && + devinfo->settings->antenna_sku && + devinfo->otp.valid) { +const struct brcmf_otp_params *otp = &devinfo->otp; +struct device *dev = &devinfo->pdev->dev; +const char **bt = fwreq->board_types; + +brcmf_dbg (PCIE ,"Apple board: %s\n" , + devinfo->settings->board_type); + +/* Example: apple,shikoku-RASP-m-6.11-X3 */ + bt[0 ] =devm_kasprintf (dev,GFP_KERNEL ,"%s-%s-%s-%s-%s" , + devinfo->settings->board_type, + otp->module, otp->vendor, otp->version, + devinfo->settings->antenna_sku); + bt[1 ] =devm_kasprintf (dev,GFP_KERNEL ,"%s-%s-%s-%s" , + devinfo->settings->board_type, + otp->module, otp->vendor, otp->version); + bt[2 ] =devm_kasprintf (dev,GFP_KERNEL ,"%s-%s-%s" , + devinfo->settings->board_type, + otp->module, otp->vendor); + bt[3 ] =devm_kasprintf (dev,GFP_KERNEL ,"%s-%s" , + devinfo->settings->board_type, + otp->module); + bt[4 ] =devm_kasprintf (dev,GFP_KERNEL ,"%s-%s" , + devinfo->settings->board_type, + devinfo->settings->antenna_sku); + bt[5 ] = devinfo->settings->board_type; + +if (!bt[0 ] || !bt[1 ] || !bt[2 ] || !bt[3 ] || !bt[4 ]) { +kfree (fwreq); +return NULL ; + } + + }else { +brcmf_dbg (PCIE ,"Board: %s\n" , devinfo->settings->board_type); + fwreq->board_types[0 ] = devinfo->settings->board_type; + }return fwreq; }
Signature · 1 line
2.30.2
Re: [PATCH wireless-next v2 07/12] brcmfmac: pcie: Perform firmware selection for Apple platforms
Quoted 69 lines · Russell King
From: Hector Martin <[email protected]>
On Apple platforms, firmware selection uses the following elements:
Property Example Source ============== ======= ======================== * Chip name 4378 Device ID * Chip revision B1 OTP * Platform shikoku DT (ARM64) or ACPI (x86) * Module type RASP OTP * Module vendor m OTP * Module version 6.11 OTP * Antenna SKU X3 DT (ARM64) or ACPI (x86)In macOS, these firmwares are stored using filenames in this format under
/usr/share/firmware/wifi:C-4378__s-B1/P-shikoku-X3_M-RASP_V-m__m-6.11.txtTo prepare firmwares for Linux, we rename these to a scheme following the existing brcmfmac convention:
brcmfmac<chip><lower(rev)>-pcie.apple,<platform>-<mod_type>-\ <mod_vendor>-<mod_version>-<antenna_sku>.txtThe NVRAM uses all the components, while the firmware and CLM blob only use the chip/revision/platform/antenna_sku:
brcmfmac<chip><lower(rev)>-pcie.apple,<platform>-<antenna_sku>.bin
e.g.
brcm/brcmfmac4378b1-pcie.apple,shikoku-RASP-m-6.11-X3.txt brcm/brcmfmac4378b1-pcie.apple,shikoku-X3.binIn addition, since there are over 1000 files in total, many of which are symlinks or outright duplicates, we deduplicate and prune the firmware tree to reduce firmware filenames to fewer dimensions. For example, the shikoku platform (MacBook Air M1 2020) simplifies to just 4 files:
brcm/brcmfmac4378b1-pcie.apple,shikoku.clm_blob brcm/brcmfmac4378b1-pcie.apple,shikoku.bin
brcm/brcmfmac4378b1-pcie.apple,shikoku-RASP-m.txtbrcm/brcmfmac4378b1-pcie.apple,shikoku-RASP-u.txtThis reduces the total file count to around 170, of which 75 are symlinks and 95 are regular files: 7 firmware blobs, 27 CLM blobs, and 61 NVRAM config files. We also slightly process NVRAM files to correct some formatting issues.
To handle this, the driver must try the following path formats when looking for firmware files:
brcm/brcmfmac4378b1-pcie.apple,shikoku-RASP-m-6.11-X3.txt brcm/brcmfmac4378b1-pcie.apple,shikoku-RASP-m-6.11.txt brcm/brcmfmac4378b1-pcie.apple,shikoku-RASP-m.txt brcm/brcmfmac4378b1-pcie.apple,shikoku-RASP.txt brcm/brcmfmac4378b1-pcie.apple,shikoku-X3.txt * brcm/brcmfmac4378b1-pcie.apple,shikoku.txt* Not relevant for NVRAM, only for
firmware/CLM.The chip revision nominally comes from OTP on Apple platforms, but it can be mapped to the PCI revision number, so we ignore the OTP revision and continue to use the existing PCI revision mechanism to identify chip revisions, as the driver already does for other chips. Unfortunately, the mapping is not consistent between different chip types, so this has to be determined experimentally.
Quoted 4 lines
Reviewed-by Linus Walleij <[email protected]>Signed-off-by Hector Martin <[email protected]>Signed-off-by Russell King (Oracle) <[email protected]>---
Quoted 38 lines
.../broadcom/brcm80211/brcmfmac/pcie.c | 41 ++++++++++++++++++- 1 file changed, 39 insertions(+), 2 deletions(-)drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c +25
-2@@ -2068,8 +2068,45 @@ brcmf_pcie_prepare_fw_request(struct brcmf_pciedev_info *devinfo) fwreq->domain_nr =pci_domain_nr (devinfo->pdev->bus) +1 ; fwreq->bus_nr = devinfo->pdev->bus->number; -brcmf_dbg (PCIE ,"Board: %s\n" , devinfo->settings->board_type); - fwreq->board_types[0 ] = devinfo->settings->board_type; +/* Apple platforms with fancy firmware/NVRAM selection */ +if (devinfo->settings->board_type && + devinfo->settings->antenna_sku && + devinfo->otp.valid) { +const struct brcmf_otp_params *otp = &devinfo->otp; +struct device *dev = &devinfo->pdev->dev; +const char **bt = fwreq->board_types; + +brcmf_dbg (PCIE ,"Apple board: %s\n" , + devinfo->settings->board_type); + +/* Example: apple,shikoku-RASP-m-6.11-X3 */ + bt[0 ] =devm_kasprintf (dev,GFP_KERNEL ,"%s-%s-%s-%s-%s" , + devinfo->settings->board_type, + otp->module, otp->vendor, otp->version, + devinfo->settings->antenna_sku); + bt[1 ] =devm_kasprintf (dev,GFP_KERNEL ,"%s-%s-%s-%s" , + devinfo->settings->board_type, + otp->module, otp->vendor, otp->version); + bt[2 ] =devm_kasprintf (dev,GFP_KERNEL ,"%s-%s-%s" , + devinfo->settings->board_type, + otp->module, otp->vendor); + bt[3 ] =devm_kasprintf (dev,GFP_KERNEL ,"%s-%s" , + devinfo->settings->board_type, + otp->module);
drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c brcmf_pcie_prepare_fw_request(struct brcmf_pciedev_info *devinfo) · line 2105
Quoted 10 lines
drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c +10
-0+ bt[4 ] =devm_kasprintf (dev,GFP_KERNEL ,"%s-%s" , + devinfo->settings->board_type, + devinfo->settings->antenna_sku); + bt[5 ] = devinfo->settings->board_type; + +if (!bt[0 ] || !bt[1 ] || !bt[2 ] || !bt[3 ] || !bt[4 ]) { +kfree (fwreq); +return NULL ; + } +
Spurious newline?
Quoted 10 lines
drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c +4
-0+ }else { +brcmf_dbg (PCIE ,"Board: %s\n" , devinfo->settings->board_type); + fwreq->board_types[0 ] = devinfo->settings->board_type; + }return fwreq; }Signature · 1 line
2.30.2
PATCH v2 8/12 brcmfmac: firmware: Allow platform to override macaddr
In reply to Russell King (Oracle)From: Hector Martin <[email protected]>
On Device Tree platforms, it is customary to be able to set the MAC address via the Device Tree, as it is often stored in system firmware. This is particularly relevant for Apple ARM64 platforms, where this information comes from system configuration and passed through by the bootloader into the DT.
Implement support for this by fetching the platform MAC address and adding or replacing the macaddr= property in nvram. This becomes the dongle's default MAC address.
On platforms with an SROM MAC address, this overrides it. On platforms without one, such as Apple ARM64 devices, this is required for the firmware to boot (it will fail if it does not have a valid MAC at all).
--- .../broadcom/brcm80211/brcmfmac/firmware.c | 31 +++++++++++++++++-- 1 file changed, 29 insertions(+), 2 deletions(-)
drivers/net/wireless/broadcom/brcm80211/brcmfmac/firmware.c +29 -2
@@ -21,6 +21,8 @@#define BRCMF_FW_NVRAM_DEVPATH_LEN 19/* devpath0=pcie/1/4/ */ #define BRCMF_FW_NVRAM_PCIEDEV_LEN 10/* pcie/1/4/ + \0 */ #define BRCMF_FW_DEFAULT_BOARDREV "boardrev=0xff" +#define BRCMF_FW_MACADDR_FMT "macaddr=%pM" +#define BRCMF_FW_MACADDR_LEN (7 + ETH_ALEN * 3)enum nvram_parser_state {IDLE ,
@@ -57,6 +59,7 @@ struct nvram_parser {bool multi_dev_v1;bool multi_dev_v2;bool boardrev_found; +bool strip_mac; };/*
@@ -121,6 +124,10 @@ static enum nvram_parser_state brcmf_nvram_handle_key(struct nvram_parser *nvp) nvp->multi_dev_v2 = true;if (strncmp (&nvp->data[nvp->entry],"boardrev" ,8 ) ==0 ) nvp->boardrev_found = true; +/* strip macaddr if platform MAC overrides */ +if (nvp->strip_mac && +strncmp (&nvp->data[nvp->entry],"macaddr" ,7 ) ==0 ) + st =COMMENT ; }else if (!is_nvram_char (c) || c ==' ' ) {brcmf_dbg (INFO ,"warning: ln=%d:col=%d: '=' expected, skip invalid key entry\n" , nvp->line, nvp->column);
@@ -209,6 +216,7 @@ static int brcmf_init_nvram_parser(struct nvram_parser *nvp, size = data_len;/* Add space for properties we may add */ size +=strlen (BRCMF_FW_DEFAULT_BOARDREV ) +1 ; + size +=BRCMF_FW_MACADDR_LEN +1 ;/* Alloc for extra 0 byte + roundup by 4 + length field */ size +=1 +3 +sizeof (u32); nvp->nvram =kzalloc (size,GFP_KERNEL );
@@ -368,22 +376,37 @@ static void brcmf_fw_add_defaults(struct nvram_parser *nvp) nvp->nvram_len++; } +static void brcmf_fw_add_macaddr (struct nvram_parser *nvp,u8 *mac) +{ +int len; + + len =scnprintf (&nvp->nvram[nvp->nvram_len],BRCMF_FW_MACADDR_LEN +1 , +BRCMF_FW_MACADDR_FMT , mac); +WARN_ON (len !=BRCMF_FW_MACADDR_LEN ); + nvp->nvram_len += len +1 ; +} +/* brcmf_nvram_strip :Takes a buffer of "<var>=<value>\n" lines read from a fil * and ending in a NUL. Removes carriage returns, empty lines, comment lines, * and converts newlines to NULs. Shortens buffer as needed and pads with NULs. * End of buffer is completed with token identifying length of buffer. */ static void *brcmf_fw_nvram_strip (const u8 *data,size_t data_len, -u32 *new_length,u16 domain_nr,u16 bus_nr) +u32 *new_length,u16 domain_nr,u16 bus_nr, +struct device *dev) {struct nvram_parser nvp;u32 pad;u32 token;__le32 token_le; +u8 mac[ETH_ALEN ];if (brcmf_init_nvram_parser (&nvp, data, data_len) <0 )return NULL ; +if (eth_platform_get_mac_address (dev, mac) ==0 ) + nvp.strip_mac = true; +while (nvp.pos < data_len) { nvp.state = nv_parser_states[nvp.state](&nvp);if (nvp.state ==END )
@@ -404,6 +427,9 @@ static void *brcmf_fw_nvram_strip(const u8 *data, size_t data_len,brcmf_fw_add_defaults (&nvp); +if (nvp.strip_mac) +brcmf_fw_add_macaddr (&nvp, mac); + pad = nvp.nvram_len; *new_length =roundup (nvp.nvram_len +1 ,4 );while (pad != *new_length) {
@@ -538,7 +564,8 @@ static int brcmf_fw_request_nvram_done(const struct firmware *fw, void *ctx)if (data) nvram =brcmf_fw_nvram_strip (data, data_len, &nvram_length, fwctx->req->domain_nr, - fwctx->req->bus_nr); + fwctx->req->bus_nr, + fwctx->dev);if (free_bcm47xx_nvram)bcm47xx_nvram_release_contents (data);
Signature · 1 line
2.30.2
Re: [PATCH wireless-next v2 08/12] brcmfmac: firmware: Allow platform to override macaddr
Quoted 37 lines · Russell King
From: Hector Martin <[email protected]>
On Device Tree platforms, it is customary to be able to set the MAC address via the Device Tree, as it is often stored in system firmware. This is particularly relevant for Apple ARM64 platforms, where this information comes from system configuration and passed through by the bootloader into the DT.
Implement support for this by fetching the platform MAC address and adding or replacing the macaddr= property in nvram. This becomes the dongle's default MAC address.
On platforms with an SROM MAC address, this overrides it. On platforms without one, such as Apple ARM64 devices, this is required for the firmware to boot (it will fail if it does not have a valid MAC at all).
Reviewed-by Linus Walleij <[email protected]>Signed-off-by Hector Martin <[email protected]>Signed-off-by Russell King (Oracle) <[email protected]>--- .../broadcom/brcm80211/brcmfmac/firmware.c | 31 +++++++++++++++++-- 1 file changed, 29 insertions(+), 2 deletions(-)drivers/net/wireless/broadcom/brcm80211/brcmfmac/firmware.c +2
-0@@ -21,6 +21,8 @@#define BRCMF_FW_NVRAM_DEVPATH_LEN 19/* devpath0=pcie/1/4/ */ #define BRCMF_FW_NVRAM_PCIEDEV_LEN 10/* pcie/1/4/ + \0 */ #define BRCMF_FW_DEFAULT_BOARDREV "boardrev=0xff" +#define BRCMF_FW_MACADDR_FMT "macaddr=%pM" +#define BRCMF_FW_MACADDR_LEN (7 + ETH_ALEN * 3)enum nvram_parser_state {IDLE ,
drivers/net/wireless/broadcom/brcm80211/brcmfmac/firmware.c struct nvram_parser { · line 62
Quoted 4 lines
drivers/net/wireless/broadcom/brcm80211/brcmfmac/firmware.c +1
-0@@ -57,6 +59,7 @@ struct nvram_parser {bool multi_dev_v1;bool multi_dev_v2;bool boardrev_found; +bool strip_mac;
CC [M] drivers/net/wireless/broadcom/brcm80211/brcmfmac/firmware.odrivers/net/wireless/broadcom/brcm80211/brcmfmac/firmware.c:63: warning: Function parameter or member 'strip_mac' not described in 'nvram_parser'
Otherwise looks OK and you can add
Quoted 84 lines
drivers/net/wireless/broadcom/brcm80211/brcmfmac/firmware.c +26
-2};/* @@ -121,6 +124,10 @@ static enum nvram_parser_state brcmf_nvram_handle_key(struct nvram_parser *nvp) nvp->multi_dev_v2 = true;if (strncmp (&nvp->data[nvp->entry],"boardrev" ,8 ) ==0 ) nvp->boardrev_found = true; +/* strip macaddr if platform MAC overrides */ +if (nvp->strip_mac && +strncmp (&nvp->data[nvp->entry],"macaddr" ,7 ) ==0 ) + st =COMMENT ; }else if (!is_nvram_char (c) || c ==' ' ) {brcmf_dbg (INFO ,"warning: ln=%d:col=%d: '=' expected, skip invalid key entry\n" , nvp->line, nvp->column);@@ -209,6 +216,7 @@ static int brcmf_init_nvram_parser(struct nvram_parser *nvp, size = data_len;/* Add space for properties we may add */ size +=strlen (BRCMF_FW_DEFAULT_BOARDREV ) +1 ; + size +=BRCMF_FW_MACADDR_LEN +1 ;/* Alloc for extra 0 byte + roundup by 4 + length field */ size +=1 +3 +sizeof (u32); nvp->nvram =kzalloc (size,GFP_KERNEL );@@ -368,22 +376,37 @@ static void brcmf_fw_add_defaults(struct nvram_parser *nvp) nvp->nvram_len++; } +static void brcmf_fw_add_macaddr (struct nvram_parser *nvp,u8 *mac) +{ +int len; + + len =scnprintf (&nvp->nvram[nvp->nvram_len],BRCMF_FW_MACADDR_LEN +1 , +BRCMF_FW_MACADDR_FMT , mac); +WARN_ON (len !=BRCMF_FW_MACADDR_LEN ); + nvp->nvram_len += len +1 ; +} +/* brcmf_nvram_strip :Takes a buffer of "<var>=<value>\n" lines read from a fil * and ending in a NUL. Removes carriage returns, empty lines, comment lines, * and converts newlines to NULs. Shortens buffer as needed and pads with NULs. * End of buffer is completed with token identifying length of buffer. */ static void *brcmf_fw_nvram_strip (const u8 *data,size_t data_len, -u32 *new_length,u16 domain_nr,u16 bus_nr) +u32 *new_length,u16 domain_nr,u16 bus_nr, +struct device *dev) {struct nvram_parser nvp;u32 pad;u32 token;__le32 token_le; +u8 mac[ETH_ALEN ];if (brcmf_init_nvram_parser (&nvp, data, data_len) <0 )return NULL ; +if (eth_platform_get_mac_address (dev, mac) ==0 ) + nvp.strip_mac = true; +while (nvp.pos < data_len) { nvp.state = nv_parser_states[nvp.state](&nvp);if (nvp.state ==END )@@ -404,6 +427,9 @@ static void *brcmf_fw_nvram_strip(const u8 *data, size_t data_len,brcmf_fw_add_defaults (&nvp); +if (nvp.strip_mac) +brcmf_fw_add_macaddr (&nvp, mac); + pad = nvp.nvram_len; *new_length =roundup (nvp.nvram_len +1 ,4 );while (pad != *new_length) {@@ -538,7 +564,8 @@ static int brcmf_fw_request_nvram_done(const struct firmware *fw, void *ctx)if (data) nvram =brcmf_fw_nvram_strip (data, data_len, &nvram_length, fwctx->req->domain_nr, - fwctx->req->bus_nr); + fwctx->req->bus_nr, + fwctx->dev);if (free_bcm47xx_nvram)bcm47xx_nvram_release_contents (data);Signature · 1 line
2.30.2
PATCH v2 9/12 brcmfmac: msgbuf: Increase RX ring sizes to 1024
In reply to Russell King (Oracle)From: Hector Martin <[email protected]>
Newer chips used on Apple platforms have a max_rxbufpost greater than 512, which causes warnings when brcmf_msgbuf_rxbuf_data_fill tries to put more entries in the ring than will fit. Increase the ring sizes to 1024.
--- drivers/net/wireless/broadcom/brcm80211/brcmfmac/msgbuf.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/net/wireless/broadcom/brcm80211/brcmfmac/msgbuf.h +2 -2
@@ -8,10 +8,10 @@#ifdef CONFIG_BRCMFMAC_PROTO_MSGBUF #define BRCMF_H2D_MSGRING_CONTROL_SUBMIT_MAX_ITEM 64 -#define BRCMF_H2D_MSGRING_RXPOST_SUBMIT_MAX_ITEM 512 +#define BRCMF_H2D_MSGRING_RXPOST_SUBMIT_MAX_ITEM 1024#define BRCMF_D2H_MSGRING_CONTROL_COMPLETE_MAX_ITEM 64#define BRCMF_D2H_MSGRING_TX_COMPLETE_MAX_ITEM 1024 -#define BRCMF_D2H_MSGRING_RX_COMPLETE_MAX_ITEM 512 +#define BRCMF_D2H_MSGRING_RX_COMPLETE_MAX_ITEM 1024#define BRCMF_H2D_TXFLOWRING_MAX_ITEM 512#define BRCMF_H2D_MSGRING_CONTROL_SUBMIT_ITEMSIZE 40
Signature · 1 line
2.30.2
Re: [PATCH wireless-next v2 09/12] brcmfmac: msgbuf: Increase RX ring sizes to 1024
Quoted 11 lines · Russell King
From: Hector Martin <[email protected]>
Newer chips used on Apple platforms have a
max_rxbufpostgreater than 512, which causes warnings whenbrcmf_msgbuf_rxbuf_data_filltries to put more entries in the ring than will fit. Increase the ring sizes to 1024.Reviewed-by Linus Walleij <[email protected]>Signed-off-by Hector Martin <[email protected]>Signed-off-by Russell King (Oracle) <[email protected]>---
PATCH v2 10/12 brcmfmac: pcie: Support PCIe core revisions >= 64
In reply to Russell King (Oracle)From: Hector Martin <[email protected]>
These newer PCIe core revisions include new sets of registers that must be used instead of the legacy ones. Introduce a brcmf_pcie_reginfo to hold the specific register offsets and values to use for a given platform, and change all the register accesses to indirect through it.
--- .../broadcom/brcm80211/brcmfmac/pcie.c | 125 +++++++++++++++--- 1 file changed, 105 insertions(+), 20 deletions(-)
drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c +105 -20
@@ -119,6 +119,12 @@ static const struct brcmf_firmware_mapping brcmf_pcie_fwnames[] = {#define BRCMF_PCIE_PCIE2REG_H2D_MAILBOX_0 0x140#define BRCMF_PCIE_PCIE2REG_H2D_MAILBOX_1 0x144 +#define BRCMF_PCIE_64_PCIE2REG_INTMASK 0xC14 +#define BRCMF_PCIE_64_PCIE2REG_MAILBOXINT 0xC30 +#define BRCMF_PCIE_64_PCIE2REG_MAILBOXMASK 0xC34 +#define BRCMF_PCIE_64_PCIE2REG_H2D_MAILBOX_0 0xA20 +#define BRCMF_PCIE_64_PCIE2REG_H2D_MAILBOX_1 0xA24 +#define BRCMF_PCIE2_INTA 0x01#define BRCMF_PCIE2_INTB 0x02
@@ -138,6 +144,8 @@ static const struct brcmf_firmware_mapping brcmf_pcie_fwnames[] = {#define BRCMF_PCIE_MB_INT_D2H3_DB0 0x400000#define BRCMF_PCIE_MB_INT_D2H3_DB1 0x800000 +#define BRCMF_PCIE_MB_INT_FN0 (BRCMF_PCIE_MB_INT_FN0_0 | \ + BRCMF_PCIE_MB_INT_FN0_1)#define BRCMF_PCIE_MB_INT_D2H_DB (BRCMF_PCIE_MB_INT_D2H0_DB0 | \ BRCMF_PCIE_MB_INT_D2H0_DB1 | \ BRCMF_PCIE_MB_INT_D2H1_DB0 | \
@@ -147,6 +155,40 @@ static const struct brcmf_firmware_mapping brcmf_pcie_fwnames[] = { BRCMF_PCIE_MB_INT_D2H3_DB0 | \ BRCMF_PCIE_MB_INT_D2H3_DB1) +#define BRCMF_PCIE_64_MB_INT_D2H0_DB0 0x1 +#define BRCMF_PCIE_64_MB_INT_D2H0_DB1 0x2 +#define BRCMF_PCIE_64_MB_INT_D2H1_DB0 0x4 +#define BRCMF_PCIE_64_MB_INT_D2H1_DB1 0x8 +#define BRCMF_PCIE_64_MB_INT_D2H2_DB0 0x10 +#define BRCMF_PCIE_64_MB_INT_D2H2_DB1 0x20 +#define BRCMF_PCIE_64_MB_INT_D2H3_DB0 0x40 +#define BRCMF_PCIE_64_MB_INT_D2H3_DB1 0x80 +#define BRCMF_PCIE_64_MB_INT_D2H4_DB0 0x100 +#define BRCMF_PCIE_64_MB_INT_D2H4_DB1 0x200 +#define BRCMF_PCIE_64_MB_INT_D2H5_DB0 0x400 +#define BRCMF_PCIE_64_MB_INT_D2H5_DB1 0x800 +#define BRCMF_PCIE_64_MB_INT_D2H6_DB0 0x1000 +#define BRCMF_PCIE_64_MB_INT_D2H6_DB1 0x2000 +#define BRCMF_PCIE_64_MB_INT_D2H7_DB0 0x4000 +#define BRCMF_PCIE_64_MB_INT_D2H7_DB1 0x8000 + +#define BRCMF_PCIE_64_MB_INT_D2H_DB (BRCMF_PCIE_64_MB_INT_D2H0_DB0 | \ + BRCMF_PCIE_64_MB_INT_D2H0_DB1 | \ + BRCMF_PCIE_64_MB_INT_D2H1_DB0 | \ + BRCMF_PCIE_64_MB_INT_D2H1_DB1 | \ + BRCMF_PCIE_64_MB_INT_D2H2_DB0 | \ + BRCMF_PCIE_64_MB_INT_D2H2_DB1 | \ + BRCMF_PCIE_64_MB_INT_D2H3_DB0 | \ + BRCMF_PCIE_64_MB_INT_D2H3_DB1 | \ + BRCMF_PCIE_64_MB_INT_D2H4_DB0 | \ + BRCMF_PCIE_64_MB_INT_D2H4_DB1 | \ + BRCMF_PCIE_64_MB_INT_D2H5_DB0 | \ + BRCMF_PCIE_64_MB_INT_D2H5_DB1 | \ + BRCMF_PCIE_64_MB_INT_D2H6_DB0 | \ + BRCMF_PCIE_64_MB_INT_D2H6_DB1 | \ + BRCMF_PCIE_64_MB_INT_D2H7_DB0 | \ + BRCMF_PCIE_64_MB_INT_D2H7_DB1) +#define BRCMF_PCIE_SHARED_VERSION_7 7#define BRCMF_PCIE_MIN_SHARED_VERSION 5#define BRCMF_PCIE_MAX_SHARED_VERSION BRCMF_PCIE_SHARED_VERSION_7
@@ -273,6 +315,7 @@ struct brcmf_pciedev_info {char nvram_name[BRCMF_FW_NAME_LEN ];char clm_name[BRCMF_FW_NAME_LEN ];const struct firmware *clm_fw; +const struct brcmf_pcie_reginfo *reginfo;void __iomem *regs;void __iomem *tcm;u32 ram_base;
@@ -359,6 +402,36 @@ static const u32 brcmf_ring_itemsize[BRCMF_NROF_COMMON_MSGRINGS] = {BRCMF_D2H_MSGRING_RX_COMPLETE_ITEMSIZE }; +struct brcmf_pcie_reginfo { +u32 intmask; +u32 mailboxint; +u32 mailboxmask; +u32 h2d_mailbox_0; +u32 h2d_mailbox_1; +u32 int_d2h_db; +u32 int_fn0; +}; + +static const struct brcmf_pcie_reginfo brcmf_reginfo_default = { + .intmask =BRCMF_PCIE_PCIE2REG_INTMASK , + .mailboxint =BRCMF_PCIE_PCIE2REG_MAILBOXINT , + .mailboxmask =BRCMF_PCIE_PCIE2REG_MAILBOXMASK , + .h2d_mailbox_0 =BRCMF_PCIE_PCIE2REG_H2D_MAILBOX_0 , + .h2d_mailbox_1 =BRCMF_PCIE_PCIE2REG_H2D_MAILBOX_1 , + .int_d2h_db =BRCMF_PCIE_MB_INT_D2H_DB , + .int_fn0 =BRCMF_PCIE_MB_INT_FN0 , +}; + +static const struct brcmf_pcie_reginfo brcmf_reginfo_64 = { + .intmask =BRCMF_PCIE_64_PCIE2REG_INTMASK , + .mailboxint =BRCMF_PCIE_64_PCIE2REG_MAILBOXINT , + .mailboxmask =BRCMF_PCIE_64_PCIE2REG_MAILBOXMASK , + .h2d_mailbox_0 =BRCMF_PCIE_64_PCIE2REG_H2D_MAILBOX_0 , + .h2d_mailbox_1 =BRCMF_PCIE_64_PCIE2REG_H2D_MAILBOX_1 , + .int_d2h_db =BRCMF_PCIE_64_MB_INT_D2H_DB , + .int_fn0 =0 , +}; +static void brcmf_pcie_setup (struct device *dev,int ret,struct brcmf_fw_request *fwreq); static struct brcmf_fw_request *
@@ -802,30 +875,29 @@ static void brcmf_pcie_bus_console_read(struct brcmf_pciedev_info *devinfo,static void brcmf_pcie_intr_disable (struct brcmf_pciedev_info *devinfo) { -brcmf_pcie_write_reg32 (devinfo,BRCMF_PCIE_PCIE2REG_MAILBOXMASK ,0 ); +brcmf_pcie_write_reg32 (devinfo, devinfo->reginfo->mailboxmask,0 ); }static void brcmf_pcie_intr_enable (struct brcmf_pciedev_info *devinfo) { -brcmf_pcie_write_reg32 (devinfo,BRCMF_PCIE_PCIE2REG_MAILBOXMASK , -BRCMF_PCIE_MB_INT_D2H_DB | -BRCMF_PCIE_MB_INT_FN0_0 | -BRCMF_PCIE_MB_INT_FN0_1 ); +brcmf_pcie_write_reg32 (devinfo, devinfo->reginfo->mailboxmask, + devinfo->reginfo->int_d2h_db | + devinfo->reginfo->int_fn0); }static void brcmf_pcie_hostready (struct brcmf_pciedev_info *devinfo) {if (devinfo->shared.flags &BRCMF_PCIE_SHARED_HOSTRDY_DB1 )brcmf_pcie_write_reg32 (devinfo, -BRCMF_PCIE_PCIE2REG_H2D_MAILBOX_1 ,1 ); + devinfo->reginfo->h2d_mailbox_1,1 ); }static irqreturn_t brcmf_pcie_quick_check_isr (int irq,void *arg) {struct brcmf_pciedev_info *devinfo = (struct brcmf_pciedev_info *)arg; -if (brcmf_pcie_read_reg32 (devinfo,BRCMF_PCIE_PCIE2REG_MAILBOXINT )) { +if (brcmf_pcie_read_reg32 (devinfo, devinfo->reginfo->mailboxint)) {brcmf_pcie_intr_disable (devinfo);brcmf_dbg (PCIE ,"Enter\n" );return IRQ_WAKE_THREAD ;
@@ -840,15 +912,14 @@ static irqreturn_t brcmf_pcie_isr_thread(int irq, void *arg)u32 status; devinfo->in_irq = true; - status =brcmf_pcie_read_reg32 (devinfo,BRCMF_PCIE_PCIE2REG_MAILBOXINT ); + status =brcmf_pcie_read_reg32 (devinfo, devinfo->reginfo->mailboxint);brcmf_dbg (PCIE ,"Enter %x\n" , status);if (status) { -brcmf_pcie_write_reg32 (devinfo,BRCMF_PCIE_PCIE2REG_MAILBOXINT , +brcmf_pcie_write_reg32 (devinfo, devinfo->reginfo->mailboxint, status); -if (status & (BRCMF_PCIE_MB_INT_FN0_0 | -BRCMF_PCIE_MB_INT_FN0_1 )) +if (status & devinfo->reginfo->int_fn0)brcmf_pcie_handle_mb_data (devinfo); -if (status &BRCMF_PCIE_MB_INT_D2H_DB ) { +if (status & devinfo->reginfo->int_d2h_db) {if (devinfo->state ==BRCMFMAC_PCIE_STATE_UP )brcmf_proto_msgbuf_rx_trigger ( &devinfo->pdev->dev);
@@ -907,8 +978,8 @@ static void brcmf_pcie_release_irq(struct brcmf_pciedev_info *devinfo)if (devinfo->in_irq)brcmf_err (bus,"Still in IRQ (processing) !!!\n" ); - status =brcmf_pcie_read_reg32 (devinfo,BRCMF_PCIE_PCIE2REG_MAILBOXINT ); -brcmf_pcie_write_reg32 (devinfo,BRCMF_PCIE_PCIE2REG_MAILBOXINT , status); + status =brcmf_pcie_read_reg32 (devinfo, devinfo->reginfo->mailboxint); +brcmf_pcie_write_reg32 (devinfo, devinfo->reginfo->mailboxint, status); devinfo->irq_allocated = false; }
@@ -960,7 +1031,7 @@ static int brcmf_pcie_ring_mb_ring_bell(void *ctx)brcmf_dbg (PCIE ,"RING !\n" );/* Any arbitrary value will do, lets use 1 */ -brcmf_pcie_write_reg32 (devinfo,BRCMF_PCIE_PCIE2REG_H2D_MAILBOX_0 ,1 ); +brcmf_pcie_write_reg32 (devinfo, devinfo->reginfo->h2d_mailbox_0,1 );return 0 ; }
@@ -1723,15 +1794,22 @@ static int brcmf_pcie_buscoreprep(void *ctx)static int brcmf_pcie_buscore_reset (void *ctx,struct brcmf_chip *chip) {struct brcmf_pciedev_info *devinfo = (struct brcmf_pciedev_info *)ctx; -u32 val; +struct brcmf_core *core; +u32 val, reg; devinfo->ci = chip;brcmf_pcie_reset_device (devinfo); - val =brcmf_pcie_read_reg32 (devinfo,BRCMF_PCIE_PCIE2REG_MAILBOXINT ); +/* reginfo is not ready yet */ + core =brcmf_chip_get_core (chip,BCMA_CORE_PCIE2 ); +if (core->rev >=64 ) + reg =BRCMF_PCIE_64_PCIE2REG_MAILBOXINT ; +else + reg =BRCMF_PCIE_PCIE2REG_MAILBOXINT ; + + val =brcmf_pcie_read_reg32 (devinfo, reg);if (val !=0xffffffff ) -brcmf_pcie_write_reg32 (devinfo,BRCMF_PCIE_PCIE2REG_MAILBOXINT , - val); +brcmf_pcie_write_reg32 (devinfo, reg, val);return 0 ; }
@@ -2118,6 +2196,7 @@ brcmf_pcie_probe(struct pci_dev *pdev, const struct pci_device_id *id)struct brcmf_fw_request *fwreq;struct brcmf_pciedev_info *devinfo;struct brcmf_pciedev *pcie_bus_dev; +struct brcmf_core *core;struct brcmf_bus *bus;brcmf_dbg (PCIE ,"Enter %x:%x\n" , pdev->vendor, pdev->device);
@@ -2137,6 +2216,12 @@ brcmf_pcie_probe(struct pci_dev *pdev, const struct pci_device_id *id) goto fail; } + core =brcmf_chip_get_core (devinfo->ci,BCMA_CORE_PCIE2 ); +if (core->rev >=64 ) + devinfo->reginfo = &brcmf_reginfo_64; +else + devinfo->reginfo = &brcmf_reginfo_default; + pcie_bus_dev =kzalloc (sizeof (*pcie_bus_dev),GFP_KERNEL );if (pcie_bus_dev ==NULL ) { ret = -ENOMEM ;
@@ -2306,7 +2391,7 @@ static int brcmf_pcie_pm_leave_D3(struct device *dev)brcmf_dbg (PCIE ,"Enter, dev=%p, bus=%p\n" , dev, bus);/* Check if device is still up and running, if so we are ready */ -if (brcmf_pcie_read_reg32 (devinfo,BRCMF_PCIE_PCIE2REG_INTMASK ) !=0 ) { +if (brcmf_pcie_read_reg32 (devinfo, devinfo->reginfo->intmask) !=0 ) {brcmf_dbg (PCIE ,"Try to wakeup device....\n" );if (brcmf_pcie_send_mb_data (devinfo,BRCMF_H2D_HOST_D0_INFORM )) goto cleanup;
Signature · 1 line
2.30.2
PATCH v2 11/12 brcmfmac: pcie: Add IDs/properties for BCM4378
In reply to Russell King (Oracle)From: Hector Martin <[email protected]>
This chip is present on Apple M1 (t8103) platforms:
* atlantisb (apple,j274): Mac mini (M1, 2020)
* honshu (apple,j293): MacBook Pro (13-inch, M1, 2020) * shikoku (apple,j313): MacBook Air (M1, 2020) * capri (apple,j456): iMac (24-inch, 4x USB-C, M1, 2020)
* santorini (apple,j457): iMac (24-inch, 2x USB-C, M1, 2020)
--- drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c | 2 ++ drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c | 8 ++++++++ .../net/wireless/broadcom/brcm80211/include/brcm_hw_ids.h | 2 ++ 3 files changed, 12 insertions(+)
drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c +2 -0
@@ -733,6 +733,8 @@ static u32 brcmf_chip_tcm_rambase(struct brcmf_chip_priv *ci)return 0x160000 ;case CY_CC_43752_CHIP_ID :return 0x170000 ; +case BRCM_CC_4378_CHIP_ID : +return 0x352000 ;default :brcmf_err ("unknown chip: %s\n" , ci->pub.name);break ;
drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c +8 -0
@@ -59,6 +59,7 @@ BRCMF_FW_DEF(4365C, "brcmfmac4365c-pcie");BRCMF_FW_DEF (4366B ,"brcmfmac4366b-pcie" ); BRCMF_FW_DEF(4366C, "brcmfmac4366c-pcie");BRCMF_FW_DEF (4371 ,"brcmfmac4371-pcie" ); +BRCMF_FW_CLM_DEF(4378B1, "brcmfmac4378b1-pcie");/* firmware config files */ MODULE_FIRMWARE (BRCMF_FW_DEFAULT_PATH "brcmfmac*-pcie.txt" );
@@ -88,6 +89,7 @@ static const struct brcmf_firmware_mapping brcmf_pcie_fwnames[] = { BRCMF_FW_ENTRY(BRCM_CC_43664_CHIP_ID, 0xFFFFFFF0, 4366C), BRCMF_FW_ENTRY(BRCM_CC_43666_CHIP_ID, 0xFFFFFFF0, 4366C),BRCMF_FW_ENTRY (BRCM_CC_4371_CHIP_ID ,0xFFFFFFFF ,4371 ), + BRCMF_FW_ENTRY(BRCM_CC_4378_CHIP_ID, 0xFFFFFFFF, 4378B1), /* 3 */ };#define BRCMF_PCIE_FW_UP_TIMEOUT 5000/* msec */
@@ -1970,6 +1972,11 @@ static int brcmf_pcie_read_otp(struct brcmf_pciedev_info *devinfo)int ret;switch (devinfo->ci->chip) { +case BRCM_CC_4378_CHIP_ID : + coreid =BCMA_CORE_GCI ; + base =0x1120 ; + words =0x170 ; +break ;default :/* OTP not supported on this chip */ return 0 ;
@@ -2458,6 +2465,7 @@ static const struct pci_device_id brcmf_pcie_devid_table[] = {BRCMF_PCIE_DEVICE (BRCM_PCIE_4366_2G_DEVICE_ID ),BRCMF_PCIE_DEVICE (BRCM_PCIE_4366_5G_DEVICE_ID ),BRCMF_PCIE_DEVICE (BRCM_PCIE_4371_DEVICE_ID ), + BRCMF_PCIE_DEVICE(BRCM_PCIE_4378_DEVICE_ID), { /* end: all zeroes */ } };
drivers/net/wireless/broadcom/brcm80211/include/brcm_hw_ids.h +2 -0
@@ -51,6 +51,7 @@#define BRCM_CC_43664_CHIP_ID 43664#define BRCM_CC_43666_CHIP_ID 43666#define BRCM_CC_4371_CHIP_ID 0x4371 +#define BRCM_CC_4378_CHIP_ID 0x4378#define CY_CC_4373_CHIP_ID 0x4373#define CY_CC_43012_CHIP_ID 43012#define CY_CC_43439_CHIP_ID 43439
@@ -88,6 +89,7 @@#define BRCM_PCIE_4366_2G_DEVICE_ID 0x43c4#define BRCM_PCIE_4366_5G_DEVICE_ID 0x43c5#define BRCM_PCIE_4371_DEVICE_ID 0x440d +#define BRCM_PCIE_4378_DEVICE_ID 0x4425/* brcmsmac IDs */
Signature · 1 line
2.30.2
Re: [PATCH wireless-next v2 11/12] brcmfmac: pcie: Add IDs/properties for BCM4378
Quoted 8 lines · Russell King
From: Hector Martin <[email protected]>
This chip is present on Apple M1 (t8103) platforms:
* atlantisb (apple,j274): Mac mini (M1, 2020)
* honshu (apple,j293): MacBook Pro (13-inch, M1, 2020) * shikoku (apple,j313): MacBook Air (M1, 2020) * capri (apple,j456): iMac (24-inch, 4x USB-C, M1, 2020)
Quoted 6 lines
* santorini (apple,j457): iMac (24-inch, 2x USB-C, M1, 2020)
Reviewed-by Linus Walleij <[email protected]>Signed-off-by Hector Martin <[email protected]>Signed-off-by Russell King (Oracle) <[email protected]>---
Quoted 31 lines
drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c | 2 ++ drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c | 8 ++++++++ .../net/wireless/broadcom/brcm80211/include/brcm_hw_ids.h | 2 ++ 3 files changed, 12 insertions(+)drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c +2
-0@@ -733,6 +733,8 @@ static u32 brcmf_chip_tcm_rambase(struct brcmf_chip_priv *ci)return 0x160000 ;case CY_CC_43752_CHIP_ID :return 0x170000 ; +case BRCM_CC_4378_CHIP_ID : +return 0x352000 ;default :brcmf_err ("unknown chip: %s\n" , ci->pub.name);break ;drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c +1
-0@@ -59,6 +59,7 @@ BRCMF_FW_DEF(4365C, "brcmfmac4365c-pcie");BRCMF_FW_DEF (4366B ,"brcmfmac4366b-pcie" ); BRCMF_FW_DEF(4366C, "brcmfmac4366c-pcie");BRCMF_FW_DEF (4371 ,"brcmfmac4371-pcie" ); +BRCMF_FW_CLM_DEF(4378B1, "brcmfmac4378b1-pcie");/* firmware config files */ MODULE_FIRMWARE (BRCMF_FW_DEFAULT_PATH "brcmfmac*-pcie.txt" );
drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c static const struct brcmf_firmware_mapping brcmf_pcie_fwnames[] = { · line 92
Quoted 4 lines
drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c +1
-0@@ -88,6 +89,7 @@ static const struct brcmf_firmware_mapping brcmf_pcie_fwnames[] = { BRCMF_FW_ENTRY(BRCM_CC_43664_CHIP_ID, 0xFFFFFFF0, 4366C), BRCMF_FW_ENTRY(BRCM_CC_43666_CHIP_ID, 0xFFFFFFF0, 4366C),BRCMF_FW_ENTRY (BRCM_CC_4371_CHIP_ID ,0xFFFFFFFF ,4371 ), + BRCMF_FW_ENTRY(BRCM_CC_4378_CHIP_ID, 0xFFFFFFFF, 4378B1), /* 3 */
What is /* 3 */?
Quoted 46 lines
drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c +6
-0};#define BRCMF_PCIE_FW_UP_TIMEOUT 5000/* msec */ @@ -1970,6 +1972,11 @@ static int brcmf_pcie_read_otp(struct brcmf_pciedev_info *devinfo)int ret;switch (devinfo->ci->chip) { +case BRCM_CC_4378_CHIP_ID : + coreid =BCMA_CORE_GCI ; + base =0x1120 ; + words =0x170 ; +break ;default :/* OTP not supported on this chip */ return 0 ;@@ -2458,6 +2465,7 @@ static const struct pci_device_id brcmf_pcie_devid_table[] = {BRCMF_PCIE_DEVICE (BRCM_PCIE_4366_2G_DEVICE_ID ),BRCMF_PCIE_DEVICE (BRCM_PCIE_4366_5G_DEVICE_ID ),BRCMF_PCIE_DEVICE (BRCM_PCIE_4371_DEVICE_ID ), + BRCMF_PCIE_DEVICE(BRCM_PCIE_4378_DEVICE_ID), { /* end: all zeroes */ } };drivers/net/wireless/broadcom/brcm80211/include/brcm_hw_ids.h +2
-0@@ -51,6 +51,7 @@#define BRCM_CC_43664_CHIP_ID 43664#define BRCM_CC_43666_CHIP_ID 43666#define BRCM_CC_4371_CHIP_ID 0x4371 +#define BRCM_CC_4378_CHIP_ID 0x4378#define CY_CC_4373_CHIP_ID 0x4373#define CY_CC_43012_CHIP_ID 43012#define CY_CC_43439_CHIP_ID 43439@@ -88,6 +89,7 @@#define BRCM_PCIE_4366_2G_DEVICE_ID 0x43c4#define BRCM_PCIE_4366_5G_DEVICE_ID 0x43c5#define BRCM_PCIE_4371_DEVICE_ID 0x440d +#define BRCM_PCIE_4378_DEVICE_ID 0x4425/* brcmsmac IDs */ Signature · 1 line
2.30.2
Re: [PATCH wireless-next v2 11/12] brcmfmac: pcie: Add IDs/properties for BCM4378
Quoted 46 lines · Alvin Šipraga
Quoted 8 lines · Russell King
From: Hector Martin <[email protected]>
This chip is present on Apple M1 (t8103) platforms:
* atlantisb (apple,j274): Mac mini (M1, 2020)
* honshu (apple,j293): MacBook Pro (13-inch, M1, 2020) * shikoku (apple,j313): MacBook Air (M1, 2020) * capri (apple,j456): iMac (24-inch, 4x USB-C, M1, 2020)Quoted 6 lines
* santorini (apple,j457): iMac (24-inch, 2x USB-C, M1, 2020)
Reviewed-by Linus Walleij <[email protected]>Signed-off-by Hector Martin <[email protected]>Signed-off-by Russell King (Oracle) <[email protected]>---
Reviewed-by Alvin Šipraga <[email protected]>Quoted 28 lines
drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c | 2 ++ drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c | 8 ++++++++ .../net/wireless/broadcom/brcm80211/include/brcm_hw_ids.h | 2 ++ 3 files changed, 12 insertions(+)drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c +2
-0@@ -733,6 +733,8 @@ static u32 brcmf_chip_tcm_rambase(struct brcmf_chip_priv *ci)return 0x160000 ;case CY_CC_43752_CHIP_ID :return 0x170000 ; +case BRCM_CC_4378_CHIP_ID : +return 0x352000 ;default :brcmf_err ("unknown chip: %s\n" , ci->pub.name);break ;drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c +1
-0@@ -59,6 +59,7 @@ BRCMF_FW_DEF(4365C, "brcmfmac4365c-pcie");BRCMF_FW_DEF (4366B ,"brcmfmac4366b-pcie" ); BRCMF_FW_DEF(4366C, "brcmfmac4366c-pcie");BRCMF_FW_DEF (4371 ,"brcmfmac4371-pcie" ); +BRCMF_FW_CLM_DEF(4378B1, "brcmfmac4378b1-pcie");
Quoted 9 lines
drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c static const struct brcmf_firmware_mapping brcmf_pcie_fwnames[] = { · line 92
Quoted 7 lines
drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c +1
-0/* firmware config files */ MODULE_FIRMWARE (BRCMF_FW_DEFAULT_PATH "brcmfmac*-pcie.txt" );@@ -88,6 +89,7 @@ static const struct brcmf_firmware_mapping brcmf_pcie_fwnames[] = { BRCMF_FW_ENTRY(BRCM_CC_43664_CHIP_ID, 0xFFFFFFF0, 4366C), BRCMF_FW_ENTRY(BRCM_CC_43666_CHIP_ID, 0xFFFFFFF0, 4366C),BRCMF_FW_ENTRY (BRCM_CC_4371_CHIP_ID ,0xFFFFFFFF ,4371 ), + BRCMF_FW_ENTRY(BRCM_CC_4378_CHIP_ID, 0xFFFFFFFF, 4378B1), /* 3 */What is /* 3 */?
Hector says that it was mentioned in the prior review round as well. It's the revision ID. The mask allows all IDs for chips where no split has been seen, but if a new one comes up that comment is there so we know where to split the mask.
Signature · 2 lines
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/ FTTP is here! 40Mbps down 10Mbps up. Decent connectivity at last!
Re: [PATCH wireless-next v2 11/12] brcmfmac: pcie: Add IDs/properties for BCM4378
Quoted 57 lines · Russell King (Oracle)
Quoted 46 lines · Alvin Šipraga
Quoted 8 lines · Russell King
From: Hector Martin <[email protected]>
This chip is present on Apple M1 (t8103) platforms:
* atlantisb (apple,j274): Mac mini (M1, 2020)
* honshu (apple,j293): MacBook Pro (13-inch, M1, 2020) * shikoku (apple,j313): MacBook Air (M1, 2020) * capri (apple,j456): iMac (24-inch, 4x USB-C, M1, 2020)Quoted 6 lines
* santorini (apple,j457): iMac (24-inch, 2x USB-C, M1, 2020)
Reviewed-by Linus Walleij <[email protected]>Signed-off-by Hector Martin <[email protected]>Signed-off-by Russell King (Oracle) <[email protected]>---
Reviewed-by Alvin Šipraga <[email protected]>Quoted 28 lines
drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c | 2 ++ drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c | 8 ++++++++ .../net/wireless/broadcom/brcm80211/include/brcm_hw_ids.h | 2 ++ 3 files changed, 12 insertions(+)drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c +2
-0@@ -733,6 +733,8 @@ static u32 brcmf_chip_tcm_rambase(struct brcmf_chip_priv *ci)return 0x160000 ;case CY_CC_43752_CHIP_ID :return 0x170000 ; +case BRCM_CC_4378_CHIP_ID : +return 0x352000 ;default :brcmf_err ("unknown chip: %s\n" , ci->pub.name);break ;drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c +1
-0@@ -59,6 +59,7 @@ BRCMF_FW_DEF(4365C, "brcmfmac4365c-pcie");BRCMF_FW_DEF (4366B ,"brcmfmac4366b-pcie" ); BRCMF_FW_DEF(4366C, "brcmfmac4366c-pcie");BRCMF_FW_DEF (4371 ,"brcmfmac4371-pcie" ); +BRCMF_FW_CLM_DEF(4378B1, "brcmfmac4378b1-pcie");Quoted 9 lines
drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c static const struct brcmf_firmware_mapping brcmf_pcie_fwnames[] = { · line 92
Quoted 7 lines
drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c +1
-0/* firmware config files */ MODULE_FIRMWARE (BRCMF_FW_DEFAULT_PATH "brcmfmac*-pcie.txt" );@@ -88,6 +89,7 @@ static const struct brcmf_firmware_mapping brcmf_pcie_fwnames[] = { BRCMF_FW_ENTRY(BRCM_CC_43664_CHIP_ID, 0xFFFFFFF0, 4366C), BRCMF_FW_ENTRY(BRCM_CC_43666_CHIP_ID, 0xFFFFFFF0, 4366C),BRCMF_FW_ENTRY (BRCM_CC_4371_CHIP_ID ,0xFFFFFFFF ,4371 ), + BRCMF_FW_ENTRY(BRCM_CC_4378_CHIP_ID, 0xFFFFFFFF, 4378B1), /* 3 */What is /* 3 */?
Quoted 4 lines
Hector says that it was mentioned in the prior review round as well. It's the revision ID. The mask allows all IDs for chips where no split has been seen, but if a new one comes up that comment is there so we know where to split the mask.
Alright, makes sense. If you happen to re-spin the series then it would be nice to include this info in the commit message.
Kind regards,
Alvin
Re: [PATCH wireless-next v2 11/12] brcmfmac: pcie: Add IDs/properties for BCM4378
Quoted 58 lines · Alvin Šipraga
Quoted 57 lines · Russell King (Oracle)
Quoted 55 lines · Alvin Šipraga
Quoted 8 lines · Russell King
From: Hector Martin <[email protected]>
This chip is present on Apple M1 (t8103) platforms:
* atlantisb (apple,j274): Mac mini (M1, 2020)
* honshu (apple,j293): MacBook Pro (13-inch, M1, 2020) * shikoku (apple,j313): MacBook Air (M1, 2020) * capri (apple,j456): iMac (24-inch, 4x USB-C, M1, 2020)Quoted 6 lines
* santorini (apple,j457): iMac (24-inch, 2x USB-C, M1, 2020)
Reviewed-by Linus Walleij <[email protected]>Signed-off-by Hector Martin <[email protected]>Signed-off-by Russell King (Oracle) <[email protected]>---
Reviewed-by Alvin Šipraga <[email protected]>Quoted 31 lines
drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c | 2 ++ drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c | 8 ++++++++ .../net/wireless/broadcom/brcm80211/include/brcm_hw_ids.h | 2 ++ 3 files changed, 12 insertions(+)drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c +2
-0@@ -733,6 +733,8 @@ static u32 brcmf_chip_tcm_rambase(struct brcmf_chip_priv *ci)return 0x160000 ;case CY_CC_43752_CHIP_ID :return 0x170000 ; +case BRCM_CC_4378_CHIP_ID : +return 0x352000 ;default :brcmf_err ("unknown chip: %s\n" , ci->pub.name);break ;drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c +1
-0@@ -59,6 +59,7 @@ BRCMF_FW_DEF(4365C, "brcmfmac4365c-pcie");BRCMF_FW_DEF (4366B ,"brcmfmac4366b-pcie" ); BRCMF_FW_DEF(4366C, "brcmfmac4366c-pcie");BRCMF_FW_DEF (4371 ,"brcmfmac4371-pcie" ); +BRCMF_FW_CLM_DEF(4378B1, "brcmfmac4378b1-pcie");/* firmware config files */ MODULE_FIRMWARE (BRCMF_FW_DEFAULT_PATH "brcmfmac*-pcie.txt" );drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c static const struct brcmf_firmware_mapping brcmf_pcie_fwnames[] = { · line 92
Quoted 4 lines
drivers/net/wireless/broadcom/brcm80211/brcmfmac/pcie.c +1
-0@@ -88,6 +89,7 @@ static const struct brcmf_firmware_mapping brcmf_pcie_fwnames[] = { BRCMF_FW_ENTRY(BRCM_CC_43664_CHIP_ID, 0xFFFFFFF0, 4366C), BRCMF_FW_ENTRY(BRCM_CC_43666_CHIP_ID, 0xFFFFFFF0, 4366C),BRCMF_FW_ENTRY (BRCM_CC_4371_CHIP_ID ,0xFFFFFFFF ,4371 ), + BRCMF_FW_ENTRY(BRCM_CC_4378_CHIP_ID, 0xFFFFFFFF, 4378B1), /* 3 */What is /* 3 */?
Quoted 7 lines
Quoted 4 lines
Hector says that it was mentioned in the prior review round as well. It's the revision ID. The mask allows all IDs for chips where no split has been seen, but if a new one comes up that comment is there so we know where to split the mask.
Alright, makes sense. If you happen to re-spin the series then it would be nice to include this info in the commit message.
And maybe even change the comment to something like:
/* revision ID 3 */
Signature · 3 lines
https://patchwork.kernel.org/project/linux-wireless/list/ https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches
PATCH v2 12/12 arm64: dts: apple: Add WiFi module and antenna properties
In reply to Russell King (Oracle)From: Hector Martin <[email protected]>
Add the new module-instance/antenna-sku properties required to select WiFi firmwares properly to all board device trees.
--- arch/arm64/boot/dts/apple/t8103-j274.dts | 4 ++++ arch/arm64/boot/dts/apple/t8103-j293.dts | 4 ++++ arch/arm64/boot/dts/apple/t8103-j313.dts | 4 ++++ arch/arm64/boot/dts/apple/t8103-j456.dts | 4 ++++ arch/arm64/boot/dts/apple/t8103-j457.dts | 4 ++++ arch/arm64/boot/dts/apple/t8103-jxxx.dtsi | 2 ++ 6 files changed, 22 insertions(+)
arch/arm64/boot/dts/apple/t8103-j274.dts +4 -0
@@ -21,6 +21,10 @@ aliases { }; }; +&wifi0 { + brcm,board-type = "apple,atlantisb"; +}; + /* * Force the bus number assignments so that we can declare some of the * on-board devices and properties that are populated by the bootloader
arch/arm64/boot/dts/apple/t8103-j293.dts +4 -0
@@ -17,6 +17,10 @@ / { model = "Apple MacBook Pro (13-inch, M1, 2020)"; }; +&wifi0 { + brcm,board-type = "apple,honshu"; +}; + /* * Remove unused PCIe ports and disable the associated DARTs. */
arch/arm64/boot/dts/apple/t8103-j313.dts +4 -0
@@ -17,6 +17,10 @@ / { model = "Apple MacBook Air (M1, 2020)"; }; +&wifi0 { + brcm,board-type = "apple,shikoku"; +}; + /* * Remove unused PCIe ports and disable the associated DARTs. */
arch/arm64/boot/dts/apple/t8103-j456.dts +4 -0
@@ -21,6 +21,10 @@ aliases { }; }; +&wifi0 { + brcm,board-type = "apple,capri"; +}; + &i2c0 { hpm2: usb-pd@3b { compatible = "apple,cd321x";
arch/arm64/boot/dts/apple/t8103-j457.dts +4 -0
@@ -21,6 +21,10 @@ aliases { }; }; +&wifi0 { + brcm,board-type = "apple,santorini"; +}; + /* * Force the bus number assignments so that we can declare some of the * on-board devices and properties that are populated by the bootloader
arch/arm64/boot/dts/apple/t8103-jxxx.dtsi +2 -0
@@ -71,8 +71,10 @@ hpm1: usb-pd@3f { &port00 { bus-range = <1 1>; wifi0: network@0,0 { + compatible = "pci14e4,4425"; reg = <0x10000 0x0 0x0 0x0 0x0>; /* To be filled by the loader */ local-mac-address = [00 00 00 00 00 00]; + apple,antenna-sku = "XX"; }; };
Signature · 1 line
2.30.2
Re: [PATCH wireless-next v2 12/12] arm64: dts: apple: Add WiFi module and antenna properties
Quoted 8 lines · Russell King (Oracle)
From: Hector Martin <[email protected]>
Add the new module-instance/antenna-sku properties required to select WiFi firmwares properly to all board device trees.
Signed-off-by Hector Martin <[email protected]>Reviewed-by Mark Kettenis <[email protected]>Signed-off-by Russell King (Oracle) <[email protected]>
Quoted 8 lines
--- arch/arm64/boot/dts/apple/t8103-j274.dts | 4 ++++ arch/arm64/boot/dts/apple/t8103-j293.dts | 4 ++++ arch/arm64/boot/dts/apple/t8103-j313.dts | 4 ++++ arch/arm64/boot/dts/apple/t8103-j456.dts | 4 ++++ arch/arm64/boot/dts/apple/t8103-j457.dts | 4 ++++ arch/arm64/boot/dts/apple/t8103-jxxx.dtsi | 2 ++ 6 files changed, 22 insertions(+)
I didn't get any reply to my question in v1 so I assume this patch 12 is ok to take to wireless-next. ARM folks, if this is not ok please let me know.
Signature · 3 lines
https://patchwork.kernel.org/project/linux-wireless/list/ https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches
Hector Martin
Acked-byRe: [PATCH wireless-next v2 12/12] arm64: dts: apple: Add WiFi module and antenna properties
Quoted 19 lines · Kalle Valo
Quoted 8 lines · Russell King (Oracle)
From: Hector Martin <[email protected]>
Add the new module-instance/antenna-sku properties required to select WiFi firmwares properly to all board device trees.
Signed-off-by Hector Martin <[email protected]>Reviewed-by Mark Kettenis <[email protected]>Signed-off-by Russell King (Oracle) <[email protected]>Quoted 8 lines
--- arch/arm64/boot/dts/apple/t8103-j274.dts | 4 ++++ arch/arm64/boot/dts/apple/t8103-j293.dts | 4 ++++ arch/arm64/boot/dts/apple/t8103-j313.dts | 4 ++++ arch/arm64/boot/dts/apple/t8103-j456.dts | 4 ++++ arch/arm64/boot/dts/apple/t8103-j457.dts | 4 ++++ arch/arm64/boot/dts/apple/t8103-jxxx.dtsi | 2 ++ 6 files changed, 22 insertions(+)
Quoted 3 lines
I didn't get any reply to my question in v1 so I assume this patch 12 is ok to take to wireless-next. ARM folks, if this is not ok please let me know.
Yup, this is OK to merge via wireless-next. In case you need it,
- Hector
Re: [PATCH wireless-next v2 12/12] arm64: dts: apple: Add WiFi module and antenna properties
Quoted 20 lines · Hector Martin
Quoted 19 lines · Kalle Valo
Quoted 16 lines · Russell King (Oracle)
From: Hector Martin <[email protected]>
Add the new module-instance/antenna-sku properties required to select WiFi firmwares properly to all board device trees.
Signed-off-by Hector Martin <[email protected]>Reviewed-by Mark Kettenis <[email protected]>Signed-off-by Russell King (Oracle) <[email protected]>--- arch/arm64/boot/dts/apple/t8103-j274.dts | 4 ++++ arch/arm64/boot/dts/apple/t8103-j293.dts | 4 ++++ arch/arm64/boot/dts/apple/t8103-j313.dts | 4 ++++ arch/arm64/boot/dts/apple/t8103-j456.dts | 4 ++++ arch/arm64/boot/dts/apple/t8103-j457.dts | 4 ++++ arch/arm64/boot/dts/apple/t8103-jxxx.dtsi | 2 ++ 6 files changed, 22 insertions(+)
Quoted 7 lines
Quoted 3 lines
I didn't get any reply to my question in v1 so I assume this patch 12 is ok to take to wireless-next. ARM folks, if this is not ok please let me know.
Yup, this is OK to merge via wireless-next. In case you need it,
Acked-by Hector Martin <[email protected]>
Perfect, thanks.
Signature · 3 lines
https://patchwork.kernel.org/project/linux-wireless/list/ https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches
Quoted 9 lines · Russell King (Oracle)
Hi,
This series adds support for bcm4378 found on Apple platforms, and has been tested on the Apple Mac Mini. It is a re-posting of a subset of Hector's previous 38 patch series, and it is believed that the comments from that review were addressed.
(I'm just the middle man; please don't complain if something has been missed.)
Hi Russell,
I reviewed this series (or actually the 30+ series) a couple of times and actually thought it was already applied. Anyway, I will go over these once more.
Regards,
Arend