net: phylink: fix PHY validation with rate adaption
Subsystems (4)
PATCH 1/1 net: phylink: fix PHY validation with rate adaption
Tim Harvey reports that link modes which he does not expect to be supported are being advertised, and this is because of the workaround we have for PHYs that switch interface modes.
Fix this up by checking whether rate matching will be used for the requested interface mode, and if rate matching will be used, perform validation only with the requested interface mode, rather than invoking this workaround.
---
I think Sean agreed that this patch was a good idea, but Tim never tested it. It would be good to get it tested.
drivers/net/phy/phylink.c | 22 ++++++++++++++++------ 1 file changed, 16 insertions(+), 6 deletions(-)
drivers/net/phy/phylink.c +16 -6
@@ -1603,19 +1603,29 @@ static int phylink_bringup_phy(struct phylink *pl, struct phy_device *phy,linkmode_copy (supported, phy->supported);linkmode_copy (config.advertising, phy->advertising); -/* Clause 45 PHYs switch their Serdes lane between several different -* modes, normally 10GBASE-R, SGMII. Some use 2500BASE-X for 2.5G -* speeds. We really need to know which interface modes the PHY and -* MAC supports to properly work out which linkmodes can be supported. +/* Check whether we would use rate matching for the proposed interface +* mode. */ -if (phy->is_c45 && + config.rate_matching =phy_get_rate_matching (phy, interface); + +/* Clause 45 PHYs may switch their Serdes lane between, e.g. 10GBASE-R, +* 5GBASE-R, 2500BASE-X and SGMII if they are not using rate matching. +* For some interface modes (e.g. RXAUI, XAUI and USXGMII) switching +* their Serdes is either unnecessary or not reasonable. +* +* For these which switch interface modes, we really need to know which +* interface modes the PHY supports to properly work out which ethtool +* linkmodes can be supported. For now, as a work-around, we validate +* against all interface modes, which may lead to more ethtool link +* modes being advertised than are actually supported. +*/ +if (phy->is_c45 && config.rate_matching ==RATE_MATCH_NONE && interface !=PHY_INTERFACE_MODE_RXAUI && interface !=PHY_INTERFACE_MODE_XAUI && interface !=PHY_INTERFACE_MODE_USXGMII ) config.interface =PHY_INTERFACE_MODE_NA ;else config.interface = interface; - config.rate_matching =phy_get_rate_matching (phy, config.interface); ret =phylink_validate (pl, supported, &config);if (ret) {
Signature · 1 line
2.30.2
This patch was applied to netdev/net.git (master) by David S. Miller <[email protected]>:
Hello:
This patch was applied to netdev/net.git (master)
by David S. Miller <[email protected]>:
Quoted 10 lines · On Thu, 24 Nov 2022 09:06:48 +0000 you wrote:
Tim Harvey reports that link modes which he does not expect to be supported are being advertised, and this is because of the workaround we have for PHYs that switch interface modes.
Fix this up by checking whether rate matching will be used for the requested interface mode, and if rate matching will be used, perform validation only with the requested interface mode, rather than invoking this workaround.
[...]
Here is the summary with links:
- [net] net: phylink: fix PHY validation with rate adaption
https://git.kernel.org/netdev/net/c/7642cc28fd37
You are awesome, thank you!
Signature · 2 lines
Deet-doot-dot, I am a bot. https://korg.docs.kernel.org/patchwork/pwbot.html