stmmac cleanups
Subsystems (6)
Russell King (Oracle)
maintainercover stmmac cleanups
Hi,
One of the comments I had on Feiyang Chen's series was concerning the initialisation of phylink... and so I've decided to do something about it, cleaning it up a bit.
This series:
1) adds a new phylink function to limit the MAC capabilities according to a maximum speed. This allows us to greatly simplify stmmac's initialisation of phylink's mac capabilities.
2) everywhere that uses priv->plat->phylink_node first converts this to a fwnode before doing anything with it. This is silly. Let's instead store it as a fwnode to eliminate these conversions in multiple places.
3) clean up passing the fwnode to phylink - it might as well happen at the phylink_create() callsite, rather than being scattered throughout the entire function.
4) same for mdio_bus_data
5) use phylink_limit_mac_speed() to handle the priv->plat->max_speed restriction.
6) add a method to get the MAC-specific capabilities from the code dealing with the MACs, and arrange to call it at an appropriate time.
7) convert the gmac4 users to use the MAC specific method.
8) same for xgmac.
9) lastly, group all the simple phylink_config initialisations together.
While looking into all of this, this raised eyebrows:
if (priv->plat->tx_queues_to_use > 1)
priv->phylink_config.mac_capabilities &=
~(MAC_10HD | MAC_100HD | MAC_1000HD);priv->plat->tx_queues_to_use is initialised by platforms to either 1, 4 or 8, and can be controlled from userspace via the --set-channels ethtool op. The implementation of this op in this driver limits the number of channels to priv->dma_cap.number_tx_queues, which is derived from the DMA hwcap.
So, the obvious questions are:
1) what guarantees that the static initialisation of tx_queues_to_use will always be less than or equal to number_tx_queues from the DMA hw cap?
2) tx_queues_to_use starts off as 1, but number_tx_queues is larger, we will leave the half-duplex capabilities in place, but userspace can increase tx_queues_to_use above 1. Does that mean half-duplex is then not supported?
3) Should we be basing the decision whether half-duplex is supported off the DMA capabilities?
4) What about priv->dma_cap.half_duplex? Doesn't that get a say in whether half-duplex is supported or not? Why isn't this used? Why is it only reported via debugfs? If it's not being used by the driver, what's the point of reporting it via debugfs?
drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c | 8 ++++ .../net/ethernet/stmicro/stmmac/dwxgmac2_core.c | 10 ++++ drivers/net/ethernet/stmicro/stmmac/hwif.h | 4 ++ drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 53 ++++++++-------------- drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c | 3 +- .../net/ethernet/stmicro/stmmac/stmmac_platform.c | 2 +- drivers/net/phy/phylink.c | 18 ++++++++ include/linux/phylink.h | 2 + include/linux/stmmac.h | 2 +- 9 files changed, 66 insertions(+), 36 deletions(-)
Signature · 2 lines
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/ FTTP is here! 80Mbps down 10Mbps up. Decent connectivity at last!
PATCH 1/9 net: phylink: add phylink_limit_mac_speed()
Add a function which can be used to limit the phylink MAC capabilities to an upper speed limit.
--- drivers/net/phy/phylink.c | 18 ++++++++++++++++++ include/linux/phylink.h | 2 ++ 2 files changed, 20 insertions(+)
drivers/net/phy/phylink.c +18 -0
@@ -426,6 +426,24 @@ static struct { { MAC_10HD, SPEED_10, DUPLEX_HALF }, }; +/** +* phylink_limit_mac_speed - limit the phylink_config to a maximum speed +* @config: pointer to a &struct phylink_config +* @max_speed: maximum speed +* +* Mask off MAC capabilities for speeds higher than the @max_speed parameter. +* Any further motifications of config.mac_capabilities will override this. +*/ +void phylink_limit_mac_speed (struct phylink_config *config,u32 max_speed) +{ +int i; + +for (i =0 ; i <ARRAY_SIZE (phylink_caps_params) && + phylink_caps_params[i].speed > max_speed; i++) + config->mac_speed &= ~phylink_caps_params.mask; +} +EXPORT_SYMBOL_GPL (phylink_limit_mac_speed); +/** * phylink_cap_from_speed_duplex - Get mac capability from speed/duplex * @speed: the speed to search for
include/linux/phylink.h +2 -0
@@ -223,6 +223,8 @@ struct phylink_config {unsigned long mac_capabilities; }; +void phylink_limit_mac_speed (struct phylink_config *config,u32 max_speed); +/** * struct phylink_mac_ops - MAC operations structure. * @validate: Validate and update the link configuration.
Signature · 1 line
2.30.2
PATCH 2/9 net: stmmac: convert plat->phylink_node to fwnode
In reply to Russell King (Oracle)All users of plat->phylink_node first convert it to a fwnode. Rather than repeatedly convert to a fwnode, store it as a fwnode. To reflect this change, call it plat->port_node instead - it is used for more than just phylink.
--- drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 4 ++-- drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c | 3 ++- drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c | 2 +- include/linux/stmmac.h | 2 +- 4 files changed, 6 insertions(+), 5 deletions(-)
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +2 -2
@@ -1153,7 +1153,7 @@ static int stmmac_init_phy(struct net_device *dev)if (!phylink_expects_phy (priv->phylink))return 0 ; - fwnode =of_fwnode_handle (priv->plat->phylink_node); + fwnode = priv->plat->port_node;if (!fwnode) fwnode =dev_fwnode (priv->device);
@@ -1200,7 +1200,7 @@ static int stmmac_init_phy(struct net_device *dev)static int stmmac_phy_setup (struct stmmac_priv *priv) {struct stmmac_mdio_bus_data *mdio_bus_data = priv->plat->mdio_bus_data; -struct fwnode_handle *fwnode =of_fwnode_handle (priv->plat->phylink_node); +struct fwnode_handle *fwnode = priv->plat->port_node;int max_speed = priv->plat->max_speed;int mode = priv->plat->phy_interface;struct phylink *phylink;
drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c +2 -1
@@ -533,11 +533,11 @@ int stmmac_mdio_register(struct net_device *ndev)int err =0 ;struct mii_bus *new_bus;struct stmmac_priv *priv =netdev_priv (ndev); -struct fwnode_handle *fwnode =of_fwnode_handle (priv->plat->phylink_node);struct stmmac_mdio_bus_data *mdio_bus_data = priv->plat->mdio_bus_data;struct device_node *mdio_node = priv->plat->mdio_node;struct device *dev = ndev->dev.parent;struct fwnode_handle *fixed_node; +struct fwnode_handle *fwnode;int addr, found, max_addr;if (!mdio_bus_data)
@@ -601,6 +601,7 @@ int stmmac_mdio_register(struct net_device *ndev)stmmac_xgmac2_mdio_read_c45 (new_bus,0 ,0 ,0 );/* If fixed-link is set, skip PHY scanning */ + fwnode = priv->plat->port_node;if (!fwnode) fwnode =dev_fwnode (priv->device);
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c +1 -1
@@ -428,7 +428,7 @@ stmmac_probe_config_dt(struct platform_device *pdev, u8 *mac) plat->phy_node =of_parse_phandle (np,"phy-handle" ,0 );/* PHYLINK automatically parses the phy-handle property */ - plat->phylink_node = np; + plat->port_node =of_fwnode_handle (np);/* Get max speed of operation from device tree */ of_property_read_u32 (np,"max-speed" , &plat->max_speed);
include/linux/stmmac.h +1 -1
@@ -227,7 +227,7 @@ struct plat_stmmacenet_data {phy_interface_t phy_interface;struct stmmac_mdio_bus_data *mdio_bus_data;struct device_node *phy_node; -struct device_node *phylink_node; +struct fwnode_handle *port_node;struct device_node *mdio_node;struct stmmac_dma_cfg *dma_cfg;struct stmmac_est *est;
Signature · 1 line
2.30.2
PATCH 3/9 net: stmmac: clean up passing fwnode to phylink
In reply to Russell King (Oracle)Move the initialisation of the fwnode variable closer to its use site, rather than scattered throughout stmmac_phy_setup().
--- drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 9 +++++---- 1 file changed, 5 insertions(+), 4 deletions(-)
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +5 -4
@@ -1200,9 +1200,9 @@ static int stmmac_init_phy(struct net_device *dev)static int stmmac_phy_setup (struct stmmac_priv *priv) {struct stmmac_mdio_bus_data *mdio_bus_data = priv->plat->mdio_bus_data; -struct fwnode_handle *fwnode = priv->plat->port_node;int max_speed = priv->plat->max_speed;int mode = priv->plat->phy_interface; +struct fwnode_handle *fwnode;struct phylink *phylink; priv->phylink_config.dev = &priv->dev->dev;
@@ -1211,9 +1211,6 @@ static int stmmac_phy_setup(struct stmmac_priv *priv) priv->phylink_config.ovr_an_inband = mdio_bus_data->xpcs_an_inband; -if (!fwnode) - fwnode =dev_fwnode (priv->device); -/* Set the platform/firmware specified interface mode */ __set_bit (mode, priv->phylink_config.supported_interfaces);
@@ -1254,6 +1251,10 @@ static int stmmac_phy_setup(struct stmmac_priv *priv) ~(MAC_10HD |MAC_100HD |MAC_1000HD ); priv->phylink_config.mac_managed_pm = true; + fwnode = priv->plat->port_node; +if (!fwnode) + fwnode =dev_fwnode (priv->device); + phylink =phylink_create (&priv->phylink_config, fwnode, mode, &stmmac_phylink_mac_ops);if (IS_ERR (phylink))
Signature · 1 line
2.30.2
PATCH 4/9 net: stmmac: use "mdio_bus_data" local variable
In reply to Russell King (Oracle)We have a local variable for priv->plat->mdio_bus_data, which we use later in the conditional if() block, but we evaluate the above within the conditional expression. Use mdio_bus_data instead. Since these will be the only two users of this local variable, move its assignment just before the if().
--- drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-)
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +4 -2
@@ -1199,7 +1199,7 @@ static int stmmac_init_phy(struct net_device *dev)static int stmmac_phy_setup (struct stmmac_priv *priv) { -struct stmmac_mdio_bus_data *mdio_bus_data = priv->plat->mdio_bus_data; +struct stmmac_mdio_bus_data *mdio_bus_data;int max_speed = priv->plat->max_speed;int mode = priv->plat->phy_interface;struct fwnode_handle *fwnode;
@@ -1207,7 +1207,9 @@ static int stmmac_phy_setup(struct stmmac_priv *priv) priv->phylink_config.dev = &priv->dev->dev; priv->phylink_config.type =PHYLINK_NETDEV ; -if (priv->plat->mdio_bus_data) + + mdio_bus_data = priv->plat->mdio_bus_data; +if (mdio_bus_data) priv->phylink_config.ovr_an_inband = mdio_bus_data->xpcs_an_inband;
Signature · 1 line
2.30.2
PATCH 5/9 net: stmmac: use phylink_limit_mac_speed()
In reply to Russell King (Oracle)Use phylink_limit_mac_speed() to limit the MAC capabilities rather than coding this for each speed.
--- .../net/ethernet/stmicro/stmmac/stmmac_main.c | 35 ++++++++----------- drivers/net/phy/phylink.c | 2 +- 2 files changed, 15 insertions(+), 22 deletions(-)
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +14 -21
@@ -1200,10 +1200,10 @@ static int stmmac_init_phy(struct net_device *dev)static int stmmac_phy_setup (struct stmmac_priv *priv) {struct stmmac_mdio_bus_data *mdio_bus_data; -int max_speed = priv->plat->max_speed;int mode = priv->plat->phy_interface;struct fwnode_handle *fwnode;struct phylink *phylink; +int max_speed; priv->phylink_config.dev = &priv->dev->dev; priv->phylink_config.type =PHYLINK_NETDEV ;
@@ -1222,29 +1222,18 @@ static int stmmac_phy_setup(struct stmmac_priv *priv) priv->phylink_config.supported_interfaces); priv->phylink_config.mac_capabilities =MAC_ASYM_PAUSE |MAC_SYM_PAUSE | -MAC_10 |MAC_100 ; - -if (!max_speed || max_speed >=1000 ) - priv->phylink_config.mac_capabilities |=MAC_1000 ; +MAC_10 |MAC_100 |MAC_1000 ;if (priv->plat->has_gmac4) { -if (!max_speed || max_speed >=2500 ) - priv->phylink_config.mac_capabilities |=MAC_2500FD ; + priv->phylink_config.mac_capabilities |=MAC_2500FD ; }else if (priv->plat->has_xgmac) { -if (!max_speed || max_speed >=2500 ) - priv->phylink_config.mac_capabilities |=MAC_2500FD ; -if (!max_speed || max_speed >=5000 ) - priv->phylink_config.mac_capabilities |=MAC_5000FD ; -if (!max_speed || max_speed >=10000 ) - priv->phylink_config.mac_capabilities |=MAC_10000FD ; -if (!max_speed || max_speed >=25000 ) - priv->phylink_config.mac_capabilities |=MAC_25000FD ; -if (!max_speed || max_speed >=40000 ) - priv->phylink_config.mac_capabilities |=MAC_40000FD ; -if (!max_speed || max_speed >=50000 ) - priv->phylink_config.mac_capabilities |=MAC_50000FD ; -if (!max_speed || max_speed >=100000 ) - priv->phylink_config.mac_capabilities |=MAC_100000FD ; + priv->phylink_config.mac_capabilities |=MAC_2500FD ; + priv->phylink_config.mac_capabilities |=MAC_5000FD ; + priv->phylink_config.mac_capabilities |=MAC_10000FD ; + priv->phylink_config.mac_capabilities |=MAC_25000FD ; + priv->phylink_config.mac_capabilities |=MAC_40000FD ; + priv->phylink_config.mac_capabilities |=MAC_50000FD ; + priv->phylink_config.mac_capabilities |=MAC_100000FD ; }/* Half-Duplex can only work with single queue */
@@ -1253,6 +1242,10 @@ static int stmmac_phy_setup(struct stmmac_priv *priv) ~(MAC_10HD |MAC_100HD |MAC_1000HD ); priv->phylink_config.mac_managed_pm = true; + max_speed = priv->plat->max_speed; +if (max_speed) +phylink_limit_mac_speed (&priv->phylink_config, max_speed); + fwnode = priv->plat->port_node;if (!fwnode) fwnode =dev_fwnode (priv->device);
drivers/net/phy/phylink.c +1 -1
@@ -440,7 +440,7 @@ void phylink_limit_mac_speed(struct phylink_config *config, u32 max_speed)for (i =0 ; i <ARRAY_SIZE (phylink_caps_params) && phylink_caps_params[i].speed > max_speed; i++) - config->mac_speed &= ~phylink_caps_params.mask; + config->mac_capabilities &= ~phylink_caps_params[i].mask; }EXPORT_SYMBOL_GPL (phylink_limit_mac_speed);
Signature · 1 line
2.30.2
Jakub Kicinski
maintainerRe: [PATCH net-next 5/9] net: stmmac: use phylink_limit_mac_speed()
drivers/net/phy/phylink.c void phylink_limit_mac_speed(struct phylink_config *config, u32 max_speed) · line 445
Quoted 12 lines · On Tue, 22 Aug 2023 19:50:24 +0100 Russell King (Oracle) wrote:
drivers/net/phy/phylink.c +1
-1@@ -440,7 +440,7 @@ void phylink_limit_mac_speed(struct phylink_config *config, u32 max_speed)for (i =0 ; i <ARRAY_SIZE (phylink_caps_params) && phylink_caps_params[i].speed > max_speed; i++) - config->mac_speed &= ~phylink_caps_params.mask; + config->mac_capabilities &= ~phylink_caps_params[i].mask; }EXPORT_SYMBOL_GPL (phylink_limit_mac_speed);
This chunk belongs to patch 1?
Signature · 1 line
pw-bot: cr
Russell King (Oracle)
maintainerRe: [PATCH net-next 5/9] net: stmmac: use phylink_limit_mac_speed()
Quoted 7 lines · Jakub Kicinski
Quoted 6 lines · On Tue, 22 Aug 2023 19:50:24 +0100 Russell King (Oracle) wrote:
drivers/net/phy/phylink.c +0
-0@@ -440,7 +440,7 @@ void phylink_limit_mac_speed(struct phylink_config *config, u32 max_speed)
Quoted 8 lines
drivers/net/phy/phylink.c void phylink_limit_mac_speed(struct phylink_config *config, u32 max_speed) · line 445
Quoted 6 lines
drivers/net/phy/phylink.c +1
-1for (i =0 ; i <ARRAY_SIZE (phylink_caps_params) && phylink_caps_params[i].speed > max_speed; i++) - config->mac_speed &= ~phylink_caps_params.mask; + config->mac_capabilities &= ~phylink_caps_params[i].mask; }EXPORT_SYMBOL_GPL (phylink_limit_mac_speed);This chunk belongs to patch 1?
Thanks for spotting that, you're absolutely right. I wonder why I didn't merge that fix into the correct patch...
In any case, I added a 10th patch to the patch set which converts the half-duplex capabilities to be positive logic. I'll resend it later today.
I also have a raft of other stmmac cleanup patches which are steadily growing at the moment!
Signature · 2 lines
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/ FTTP is here! 80Mbps down 10Mbps up. Decent connectivity at last!
PATCH 6/9 net: stmmac: provide stmmac_mac_phylink_get_caps()
In reply to Russell King (Oracle)Allow MACs to provide their own capabilities via the MAC operations struct.
--- drivers/net/ethernet/stmicro/stmmac/hwif.h | 4 ++++ drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 3 +++ 2 files changed, 7 insertions(+)
drivers/net/ethernet/stmicro/stmmac/hwif.h +4 -0
@@ -300,6 +300,8 @@ struct stmmac_est;struct stmmac_ops {/* MAC core initialization */ void (*core_init)(struct mac_device_info *hw,struct net_device *dev); +/* Get phylink capabilities */ +void (*phylink_get_caps)(struct stmmac_priv *priv);/* Enable the MAC RX/TX */ void (*set_mac)(void __iomem *ioaddr,bool enable);/* Enable and verify that the IPC module is supported */
@@ -419,6 +421,8 @@ struct stmmac_ops { #define stmmac_core_init(__priv, __args...) \ stmmac_do_void_callback(__priv, mac, core_init, __args) +#define stmmac_mac_phylink_get_caps (__priv) \ + stmmac_do_void_callback(__priv, mac, phylink_get_caps, __priv) #define stmmac_mac_set(__priv, __args...) \ stmmac_do_void_callback(__priv, mac, set_mac, __args) #define stmmac_rx_ipc(__priv, __args...) \
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +3 -0
@@ -1224,6 +1224,9 @@ static int stmmac_phy_setup(struct stmmac_priv *priv) priv->phylink_config.mac_capabilities =MAC_ASYM_PAUSE |MAC_SYM_PAUSE |MAC_10 |MAC_100 |MAC_1000 ; +/* Get the MAC specific capabilities */ +stmmac_mac_phylink_get_caps (priv); +if (priv->plat->has_gmac4) { priv->phylink_config.mac_capabilities |=MAC_2500FD ; }else if (priv->plat->has_xgmac) {
Signature · 1 line
2.30.2
PATCH 7/9 net: stmmac: move gmac4 specific phylink capabilities to gmac4
In reply to Russell King (Oracle)Move the setup of gmac4 speicifc phylink capabilities into gmac4 code.
--- drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c | 8 ++++++++ drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 4 +--- 2 files changed, 9 insertions(+), 3 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c +8 -0
@@ -68,6 +68,11 @@ static void dwmac4_core_init(struct mac_device_info *hw,init_waitqueue_head (&priv->tstamp_busy_wait); } +static void dwmac4_phylink_get_caps (struct stmmac_priv *priv) +{ + priv->phylink_config.mac_capabilities |=MAC_2500FD ; +} +static void dwmac4_rx_queue_enable (struct mac_device_info *hw,u8 mode,u32 queue) {
@@ -1131,6 +1136,7 @@ static int dwmac4_config_l4_filter(struct mac_device_info *hw, u32 filter_no,const struct stmmac_ops dwmac4_ops = { .core_init = dwmac4_core_init, + .phylink_get_caps = dwmac4_phylink_get_caps, .set_mac = stmmac_set_mac, .rx_ipc = dwmac4_rx_ipc_enable, .rx_queue_enable = dwmac4_rx_queue_enable,
@@ -1173,6 +1179,7 @@ const struct stmmac_ops dwmac4_ops = {const struct stmmac_ops dwmac410_ops = { .core_init = dwmac4_core_init, + .phylink_get_caps = dwmac4_phylink_get_caps, .set_mac = stmmac_dwmac4_set_mac, .rx_ipc = dwmac4_rx_ipc_enable, .rx_queue_enable = dwmac4_rx_queue_enable,
@@ -1221,6 +1228,7 @@ const struct stmmac_ops dwmac410_ops = {const struct stmmac_ops dwmac510_ops = { .core_init = dwmac4_core_init, + .phylink_get_caps = dwmac4_phylink_get_caps, .set_mac = stmmac_dwmac4_set_mac, .rx_ipc = dwmac4_rx_ipc_enable, .rx_queue_enable = dwmac4_rx_queue_enable,
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +1 -3
@@ -1227,9 +1227,7 @@ static int stmmac_phy_setup(struct stmmac_priv *priv)/* Get the MAC specific capabilities */ stmmac_mac_phylink_get_caps (priv); -if (priv->plat->has_gmac4) { - priv->phylink_config.mac_capabilities |=MAC_2500FD ; - }else if (priv->plat->has_xgmac) { +if (priv->plat->has_xgmac) { priv->phylink_config.mac_capabilities |=MAC_2500FD ; priv->phylink_config.mac_capabilities |=MAC_5000FD ; priv->phylink_config.mac_capabilities |=MAC_10000FD ;
Signature · 1 line
2.30.2
PATCH 8/9 net: stmmac: move xgmac specific phylink caps to dwxgmac2 core
In reply to Russell King (Oracle)Move the xgmac specific phylink capabilities to the dwxgmac2 support core.
--- drivers/net/ethernet/stmicro/stmmac/dwxgmac2_core.c | 10 ++++++++++ drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 10 ---------- 2 files changed, 10 insertions(+), 10 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwxgmac2_core.c +10 -0
@@ -47,6 +47,14 @@ static void dwxgmac2_core_init(struct mac_device_info *hw,writel (XGMAC_INT_DEFAULT_EN , ioaddr +XGMAC_INT_EN ); } +static void xgmac_phylink_get_caps (struct stmmac_priv *priv) +{ + priv->phylink_config.mac_capabilities |=MAC_2500FD |MAC_5000FD | +MAC_10000FD |MAC_25000FD | +MAC_40000FD |MAC_50000FD | +MAC_100000FD ; +} +static void dwxgmac2_set_mac (void __iomem *ioaddr,bool enable) {u32 tx =readl (ioaddr +XGMAC_TX_CONFIG );
@@ -1490,6 +1498,7 @@ static void dwxgmac3_fpe_configure(void __iomem *ioaddr, u32 num_txq,const struct stmmac_ops dwxgmac210_ops = { .core_init = dwxgmac2_core_init, + .phylink_get_caps = xgmac_phylink_get_caps, .set_mac = dwxgmac2_set_mac, .rx_ipc = dwxgmac2_rx_ipc, .rx_queue_enable = dwxgmac2_rx_queue_enable,
@@ -1551,6 +1560,7 @@ static void dwxlgmac2_rx_queue_enable(struct mac_device_info *hw, u8 mode,const struct stmmac_ops dwxlgmac2_ops = { .core_init = dwxgmac2_core_init, + .phylink_get_caps = xgmac_phylink_get_caps, .set_mac = dwxgmac2_set_mac, .rx_ipc = dwxgmac2_rx_ipc, .rx_queue_enable = dwxlgmac2_rx_queue_enable,
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +0 -10
@@ -1227,16 +1227,6 @@ static int stmmac_phy_setup(struct stmmac_priv *priv)/* Get the MAC specific capabilities */ stmmac_mac_phylink_get_caps (priv); -if (priv->plat->has_xgmac) { - priv->phylink_config.mac_capabilities |=MAC_2500FD ; - priv->phylink_config.mac_capabilities |=MAC_5000FD ; - priv->phylink_config.mac_capabilities |=MAC_10000FD ; - priv->phylink_config.mac_capabilities |=MAC_25000FD ; - priv->phylink_config.mac_capabilities |=MAC_40000FD ; - priv->phylink_config.mac_capabilities |=MAC_50000FD ; - priv->phylink_config.mac_capabilities |=MAC_100000FD ; - } -/* Half-Duplex can only work with single queue */ if (priv->plat->tx_queues_to_use >1 ) priv->phylink_config.mac_capabilities &=
Signature · 1 line
2.30.2
PATCH 9/9 net: stmmac: move priv->phylink_config.mac_managed_pm
In reply to Russell King (Oracle)Move priv->phylink_config.mac_managed_pm to be along side the other phylink initialisations.
--- drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +1 -1
@@ -1207,6 +1207,7 @@ static int stmmac_phy_setup(struct stmmac_priv *priv) priv->phylink_config.dev = &priv->dev->dev; priv->phylink_config.type =PHYLINK_NETDEV ; + priv->phylink_config.mac_managed_pm = true; mdio_bus_data = priv->plat->mdio_bus_data;if (mdio_bus_data)
@@ -1231,7 +1232,6 @@ static int stmmac_phy_setup(struct stmmac_priv *priv)if (priv->plat->tx_queues_to_use >1 ) priv->phylink_config.mac_capabilities &= ~(MAC_10HD |MAC_100HD |MAC_1000HD ); - priv->phylink_config.mac_managed_pm = true; max_speed = priv->plat->max_speed;if (max_speed)
Signature · 1 line
2.30.2