net: stmmac: lpc18xx: use plat_dat->phy_interface
Subsystems (5)
PATCH 1/1 net: stmmac: lpc18xx: use plat_dat->phy_interface
lpc18xx uses plat_dat->mac_interface, despite wanting to validate the PHY interface. Checking the DT files (arch/arm/boot/dts/nxp/lpc/), none of them specify mac-mode which means mac_interface and phy_interface will be identical.
mac_interface is only used when there is some kind of MII converter between the DesignWare MAC and PHY, and describes the interface mode that the DW MAC needs to use, whereas phy_interface describes the interface mode that the PHY uses.
Noting that lpc18xx only supports MII and RMII interface modes, switch this glue driver to use plat_dat->phy_interface, and to mark that the mac_interface is not used, explicitly set it to PHY_INTERFACE_MODE_NA. The latter is safe as the only user of mac_interface for this platform would be in stmmac_check_pcs_mode(), which only checks for RGMII or SGMII.
--- drivers/net/ethernet/stmicro/stmmac/dwmac-lpc18xx.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-lpc18xx.c +3 -2
@@ -41,6 +41,7 @@ static int lpc18xx_dwmac_probe(struct platform_device *pdev)if (IS_ERR (plat_dat))return PTR_ERR (plat_dat); + plat_dat->mac_interface =PHY_INTERFACE_MODE_NA ; plat_dat->has_gmac = true; reg =syscon_regmap_lookup_by_compatible ("nxp,lpc1850-creg" );
@@ -49,9 +50,9 @@ static int lpc18xx_dwmac_probe(struct platform_device *pdev)return PTR_ERR (reg); } -if (plat_dat->mac_interface ==PHY_INTERFACE_MODE_MII ) { +if (plat_dat->phy_interface ==PHY_INTERFACE_MODE_MII ) { ethmode =LPC18XX_CREG_CREG6_ETHMODE_MII ; - }else if (plat_dat->mac_interface ==PHY_INTERFACE_MODE_RMII ) { + }else if (plat_dat->phy_interface ==PHY_INTERFACE_MODE_RMII ) { ethmode =LPC18XX_CREG_CREG6_ETHMODE_RMII ; }else {dev_err (&pdev->dev,"Only MII and RMII mode supported\n" );
Signature · 1 line
2.30.2
Quoted 10 lines · Russell King (Oracle)
lpc18xx uses
plat_dat->mac_interface, despite wanting to validate the PHY interface. Checking the DT files (arch/arm/boot/dts/nxp/lpc/), none of them specify mac-mode which meansmac_interfaceandphy_interfacewill be identical.
mac_interfaceis only used when there is some kind of MII converter between the DesignWare MAC and PHY, and describes the interface mode that the DW MAC needs to use, whereasphy_interfacedescribes the interface mode that the PHY uses.
Quoted 8 lines
Noting that lpc18xx only supports MII and RMII interface modes, switch this glue driver to use
plat_dat->phy_interface, and to mark that themac_interfaceis not used, explicitly set it toPHY_INTERFACE_MODE_NA. The latter is safe as the only user ofmac_interfacefor this platform would be instmmac_check_pcs_mode(), which only checks for RGMII or SGMII.Signed-off-by Russell King (Oracle) <[email protected]>
Thanks,
Yanteng
Quoted 28 lines
--- drivers/net/ethernet/stmicro/stmmac/dwmac-lpc18xx.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-)drivers/net/ethernet/stmicro/stmmac/dwmac-lpc18xx.c +3
-2@@ -41,6 +41,7 @@ static int lpc18xx_dwmac_probe(struct platform_device *pdev)if (IS_ERR (plat_dat))return PTR_ERR (plat_dat); + plat_dat->mac_interface =PHY_INTERFACE_MODE_NA ; plat_dat->has_gmac = true; reg =syscon_regmap_lookup_by_compatible ("nxp,lpc1850-creg" );@@ -49,9 +50,9 @@ static int lpc18xx_dwmac_probe(struct platform_device *pdev)return PTR_ERR (reg); } -if (plat_dat->mac_interface ==PHY_INTERFACE_MODE_MII ) { +if (plat_dat->phy_interface ==PHY_INTERFACE_MODE_MII ) { ethmode =LPC18XX_CREG_CREG6_ETHMODE_MII ; - }else if (plat_dat->mac_interface ==PHY_INTERFACE_MODE_RMII ) { + }else if (plat_dat->phy_interface ==PHY_INTERFACE_MODE_RMII ) { ethmode =LPC18XX_CREG_CREG6_ETHMODE_RMII ; }else {dev_err (&pdev->dev,"Only MII and RMII mode supported\n" );
This patch was applied to netdev/net-next.git (main) by Jakub Kicinski <[email protected]>:
Hello:
This patch was applied to netdev/net-next.git (main) by Jakub Kicinski <[email protected]>:
Quoted 11 lines · On Thu, 19 Jun 2025 10:47:26 +0100 you wrote:
lpc18xx uses
plat_dat->mac_interface, despite wanting to validate the PHY interface. Checking the DT files (arch/arm/boot/dts/nxp/lpc/), none of them specify mac-mode which meansmac_interfaceandphy_interfacewill be identical.
mac_interfaceis only used when there is some kind of MII converter between the DesignWare MAC and PHY, and describes the interface mode that the DW MAC needs to use, whereasphy_interfacedescribes the interface mode that the PHY uses.[...]
Here is the summary with links:
- [net-next] net: stmmac: lpc18xx: use plat_dat->phy_interface
https://git.kernel.org/netdev/net-next/c/9f22c3ddb8cf
You are awesome, thank you!
Signature · 2 lines
Deet-doot-dot, I am a bot. https://korg.docs.kernel.org/patchwork/pwbot.html