Skip to contentSkip to conversation

net: phy: realtek: fix RTL8211F wake-on-lan support

PATCH Applied Russell King (Oracle) 5 participants 8 messages Aug 13, 2025 – Aug 19, 2025

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 net: phy: realtek: fix RTL8211F wake-on-lan support

Implement Wake-on-Lan for RTL8211F correctly. The existing implementation has multiple issues:

1. It assumes that Wake-on-Lan can always be used, whether or not the interrupt is wired, and whether or not the interrupt is capable of waking the system. This breaks the ability for MAC drivers to detect whether the PHY WoL is functional.
2. switching the interrupt pin in the .set_wol() method to PMEB mode immediately silences link-state interrupts, which breaks phylib when interrupts are being used rather than polling mode.
3. the code claiming to "reset WOL status" was doing nothing of the sort. Bit 15 in page 0xd8a register 17 controls WoL reset, and needs to be pulsed low to reset the WoL state. This bit was always written as '1', resulting in no reset.
4. not resetting WoL state results in the PMEB pin remaining asserted, which in turn leads to an interrupt storm. Only resetting the WoL state in .set_wol() is not sufficient.
5. PMEB mode does not allow software detection of the wake-up event as there is no status bit to indicate we received the WoL packet.
6. across reboots of at least the Jetson Xavier NX system, the WoL configuration is preserved.

Fix all of these issues by essentially rewriting the support. We:
1. clear the WoL event enable register at probe time.
2. detect whether we can support wake-up by having a valid interrupt, and the "wakeup-source" property in DT. If we can, then we mark the MDIO device as wakeup capable, and associate the interrupt with the wakeup source.
3. arrange for the get_wol() and set_wol() implementations to handle the case where the MDIO device has not been marked as wakeup capable (thereby returning no WoL support, and refusing to enable WoL support.)
4. avoid switching to PMEB mode, instead using INTB mode with the interrupt enable, reconfiguring the interrupt enables at suspend time, and restoring their original state at resume time (we track the state of the interrupt enable register in .config_intr() register.)
5. move WoL reset from .set_wol() to the suspend function to ensure that WoL state is cleared prior to suspend. This is necessary after the PME interrupt has been enabled as a second WoL packet will not re-raise a previously cleared PME interrupt.
6. when a PME interrupt (for wakeup) is asserted, pass this to the PM wakeup so it knows which device woke the system.

This fixes WoL support in the Realtek RTL8211F driver when used on the nVidia Jetson Xavier NX platform, and needs to be applied before stmmac patches which allow these platforms to forward the ethtool WoL commands to the Realtek PHY.

---
 drivers/net/phy/realtek/realtek_main.c | 172 ++++++++++++++++++++-----
 1 file changed, 140 insertions(+), 32 deletions(-)
drivers/net/phy/realtek/realtek_main.c +140 -32
index dd0d675149ad..4361529e68fb 100644
@@ -10,6 +10,7 @@
 #include <linux/bitops.h>
 #include <linux/of.h>
 #include <linux/phy.h>
+#include <linux/pm_wakeirq.h>
 #include <linux/netdevice.h>
 #include <linux/module.h>
 #include <linux/delay.h>
@@ -31,6 +32,7 @@
 #define RTL821x_INER				0x12
 #define RTL8211B_INER_INIT			0x6400
 #define RTL8211E_INER_LINK_STATUS		BIT(10)
+#define RTL8211F_INER_PME			BIT(7)
 #define RTL8211F_INER_LINK_STATUS		BIT(4)
 
 #define RTL821x_INSR				0x13
@@ -96,17 +98,13 @@
 #define RTL8211F_RXCR				0x15
 #define RTL8211F_RX_DELAY			BIT(3)
 
-/* RTL8211F WOL interrupt configuration */
-#define RTL8211F_INTBCR_PAGE			0xd40
-#define RTL8211F_INTBCR				0x16
-#define RTL8211F_INTBCR_INTB_PMEB		BIT(5)
-
 /* RTL8211F WOL settings */
-#define RTL8211F_WOL_SETTINGS_PAGE		0xd8a
+#define RTL8211F_WOL_PAGE		0xd8a
 #define RTL8211F_WOL_SETTINGS_EVENTS		16
 #define RTL8211F_WOL_EVENT_MAGIC		BIT(12)
-#define RTL8211F_WOL_SETTINGS_STATUS		17
-#define RTL8211F_WOL_STATUS_RESET		(BIT(15) | 0x1fff)
+#define RTL8211F_WOL_RST_RMSQ		17
+#define RTL8211F_WOL_RG_RSTB			BIT(15)
+#define RTL8211F_WOL_RMSQ			0x1fff
 
 /* RTL8211F Unique phyiscal and multicast address (WOL) */
 #define RTL8211F_PHYSICAL_ADDR_PAGE		0xd8c
@@ -172,7 +170,8 @@ struct rtl821x_priv {
 	u16 phycr2;
 	bool has_phycr2;
 	struct clk *clk;
-	u32 saved_wolopts;
+	/* rtl8211f */
+	u16 iner;
 };
 
 static int rtl821x_read_page(struct phy_device *phydev)
@@ -255,6 +254,34 @@ static int rtl821x_probe(struct phy_device *phydev)
 	return 0;
 }
 
+static int rtl8211f_probe(struct phy_device *phydev)
+{
+	struct device *dev = &phydev->mdio.dev;
+	int ret;
+
+	ret = rtl821x_probe(phydev);
+	if (ret < 0)
+		return ret;
+
+	/* Disable all PME events */
+	ret = phy_write_paged(phydev, RTL8211F_WOL_PAGE,
+			      RTL8211F_WOL_SETTINGS_EVENTS, 0);
+	if (ret < 0)
+		return ret;
+
+	/* Mark this PHY as wakeup capable and register the interrupt as a
+	 * wakeup IRQ if the PHY is marked as a wakeup source in firmware,
+	 * and the interrupt is valid.
+	 */
+	if (device_property_read_bool(dev, "wakeup-source") &&
+	    phy_interrupt_is_valid(phydev)) {
+		device_set_wakeup_capable(dev, true);
+		devm_pm_set_wake_irq(dev, phydev->irq);
+	}
+
+	return ret;
+}
+
 static int rtl8201_ack_interrupt(struct phy_device *phydev)
 {
 	int err;
@@ -352,6 +379,7 @@ static int rtl8211e_config_intr(struct phy_device *phydev)
 
 static int rtl8211f_config_intr(struct phy_device *phydev)
 {
+	struct rtl821x_priv *priv = phydev->priv;
 	u16 val;
 	int err;
 
@@ -362,8 +390,10 @@ static int rtl8211f_config_intr(struct phy_device *phydev)
 
 		val = RTL8211F_INER_LINK_STATUS;
 		err = phy_write_paged(phydev, 0xa42, RTL821x_INER, val);
+		if (err == 0)
+			priv->iner = val;
 	} else {
-		val = 0;
+		priv->iner = val = 0;
 		err = phy_write_paged(phydev, 0xa42, RTL821x_INER, val);
 		if (err)
 			return err;
@@ -426,21 +456,34 @@ static irqreturn_t rtl8211f_handle_interrupt(struct phy_device *phydev)
 		return IRQ_NONE;
 	}
 
-	if (!(irq_status & RTL8211F_INER_LINK_STATUS))
-		return IRQ_NONE;
+	if (irq_status & RTL8211F_INER_LINK_STATUS) {
+		phy_trigger_machine(phydev);
+		return IRQ_HANDLED;
+	}
 
-	phy_trigger_machine(phydev);
+	if (irq_status & RTL8211F_INER_PME) {
+		pm_wakeup_event(&phydev->mdio.dev, 0);
+		return IRQ_HANDLED;
+	}
 
-	return IRQ_HANDLED;
+	return IRQ_NONE;
 }
 
 static void rtl8211f_get_wol(struct phy_device *dev, struct ethtool_wolinfo *wol)
 {
 	int wol_events;
 
+	/* If the PHY is not capable of waking the system, then WoL can not
+	 * be supported.
+	 */
+	if (!device_can_wakeup(&dev->mdio.dev)) {
+		wol->supported = 0;
+		return;
+	}
+
 	wol->supported = WAKE_MAGIC;
 
-	wol_events = phy_read_paged(dev, RTL8211F_WOL_SETTINGS_PAGE, RTL8211F_WOL_SETTINGS_EVENTS);
+	wol_events = phy_read_paged(dev, RTL8211F_WOL_PAGE, RTL8211F_WOL_SETTINGS_EVENTS);
 	if (wol_events < 0)
 		return;
 
@@ -453,6 +496,9 @@ static int rtl8211f_set_wol(struct phy_device *dev, struct ethtool_wolinfo *wol)
 	const u8 *mac_addr = dev->attached_dev->dev_addr;
 	int oldpage;
 
+	if (!device_can_wakeup(&dev->mdio.dev))
+		return -EOPNOTSUPP;
+
 	oldpage = phy_save_page(dev);
 	if (oldpage < 0)
 		goto err;
@@ -464,25 +510,23 @@ static int rtl8211f_set_wol(struct phy_device *dev, struct ethtool_wolinfo *wol)
 		__phy_write(dev, RTL8211F_PHYSICAL_ADDR_WORD1, mac_addr[3] << 8 | (mac_addr[2]));
 		__phy_write(dev, RTL8211F_PHYSICAL_ADDR_WORD2, mac_addr[5] << 8 | (mac_addr[4]));
 
-		/* Enable magic packet matching and reset WOL status */
-		rtl821x_write_page(dev, RTL8211F_WOL_SETTINGS_PAGE);
+		/* Enable magic packet matching */
+		rtl821x_write_page(dev, RTL8211F_WOL_PAGE);
 		__phy_write(dev, RTL8211F_WOL_SETTINGS_EVENTS, RTL8211F_WOL_EVENT_MAGIC);
-		__phy_write(dev, RTL8211F_WOL_SETTINGS_STATUS, RTL8211F_WOL_STATUS_RESET);
-
-		/* Enable the WOL interrupt */
-		rtl821x_write_page(dev, RTL8211F_INTBCR_PAGE);
-		__phy_set_bits(dev, RTL8211F_INTBCR, RTL8211F_INTBCR_INTB_PMEB);
+		/* Set the maximum packet size, and assert WoL reset */
+		__phy_write(dev, RTL8211F_WOL_RST_RMSQ, RTL8211F_WOL_RMSQ);
 	} else {
-		/* Disable the WOL interrupt */
-		rtl821x_write_page(dev, RTL8211F_INTBCR_PAGE);
-		__phy_clear_bits(dev, RTL8211F_INTBCR, RTL8211F_INTBCR_INTB_PMEB);
-
-		/* Disable magic packet matching and reset WOL status */
-		rtl821x_write_page(dev, RTL8211F_WOL_SETTINGS_PAGE);
+		/* Disable magic packet matching */
+		rtl821x_write_page(dev, RTL8211F_WOL_PAGE);
 		__phy_write(dev, RTL8211F_WOL_SETTINGS_EVENTS, 0);
-		__phy_write(dev, RTL8211F_WOL_SETTINGS_STATUS, RTL8211F_WOL_STATUS_RESET);
+
+		/* Place WoL in reset */
+		__phy_clear_bits(dev, RTL8211F_WOL_RST_RMSQ,
+				 RTL8211F_WOL_RG_RSTB);
 	}
 
+	device_set_wakeup_enable(&dev->mdio.dev, !!(wol->wolopts & WAKE_MAGIC));
+
 err:
 	return phy_restore_page(dev, oldpage, 0);
 }
@@ -628,6 +672,52 @@ static int rtl821x_suspend(struct phy_device *phydev)
 	return ret;
 }
 
+static int rtl8211f_suspend(struct phy_device *phydev)
+{
+	u16 wol_rst;
+	int ret;
+
+	ret = rtl821x_suspend(phydev);
+	if (ret < 0)
+		return ret;
+
+	/* If a PME event is enabled, then configure the interrupt for
+	 * PME events only, disabling link interrupt. We avoid switching
+	 * to PMEB mode as we don't have a status bit for that.
+	 */
+	if (device_may_wakeup(&phydev->mdio.dev)) {
+		ret = phy_write_paged(phydev, 0xa42, RTL821x_INER,
+				      RTL8211F_INER_PME);
+		if (ret < 0)
+			goto err;
+
+		/* Read the INSR to clear any pending interrupt */
+		phy_read_paged(phydev, RTL8211F_INSR_PAGE, RTL8211F_INSR);
+
+		/* Reset the WoL to ensure that an event is picked up.
+		 * Unless we do this, even if we receive another packet,
+		 * we may not have a PME interrupt raised.
+		 */
+		ret = phy_read_paged(phydev, RTL8211F_WOL_PAGE,
+				     RTL8211F_WOL_RST_RMSQ);
+		if (ret < 0)
+			goto err;
+
+		wol_rst = ret & ~RTL8211F_WOL_RG_RSTB;
+		ret = phy_write_paged(phydev, RTL8211F_WOL_PAGE,
+				      RTL8211F_WOL_RST_RMSQ, wol_rst);
+		if (ret < 0)
+			goto err;
+
+		wol_rst |= RTL8211F_WOL_RG_RSTB;
+		ret = phy_write_paged(phydev, RTL8211F_WOL_PAGE,
+				      RTL8211F_WOL_RST_RMSQ, wol_rst);
+	}
+
+err:
+	return ret;
+}
+
 static int rtl821x_resume(struct phy_device *phydev)
 {
 	struct rtl821x_priv *priv = phydev->priv;
@@ -645,6 +735,24 @@ static int rtl821x_resume(struct phy_device *phydev)
 	return 0;
 }
 
+static int rtl8211f_resume(struct phy_device *phydev)
+{
+	struct rtl821x_priv *priv = phydev->priv;
+	int ret;
+
+	ret = rtl821x_resume(phydev);
+	if (ret < 0)
+		return ret;
+
+	/* If the device was programmed for a PME event, restore the interrupt
+	 * enable so phylib can receive link state interrupts.
+	 */
+	if (device_may_wakeup(&phydev->mdio.dev))
+		ret = phy_write_paged(phydev, 0xa42, RTL821x_INER, priv->iner);
+
+	return ret;
+}
+
 static int rtl8211x_led_hw_is_supported(struct phy_device *phydev, u8 index,
 					unsigned long rules)
 {
@@ -1612,15 +1720,15 @@ static struct phy_driver realtek_drvs[] = {
 	}, {
 		PHY_ID_MATCH_EXACT(0x001cc916),
 		.name		= "RTL8211F Gigabit Ethernet",
-		.probe		= rtl821x_probe,
+		.probe		= rtl8211f_probe,
 		.config_init	= &rtl8211f_config_init,
 		.read_status	= rtlgen_read_status,
 		.config_intr	= &rtl8211f_config_intr,
 		.handle_interrupt = rtl8211f_handle_interrupt,
 		.set_wol	= rtl8211f_set_wol,
 		.get_wol	= rtl8211f_get_wol,
-		.suspend	= rtl821x_suspend,
-		.resume		= rtl821x_resume,
+		.suspend	= rtl8211f_suspend,
+		.resume		= rtl8211f_resume,
 		.read_page	= rtl821x_read_page,
 		.write_page	= rtl821x_write_page,
 		.flags		= PHY_ALWAYS_CALL_SUSPEND,
Signature · 1 line
2.30.2
#1 lore raw

Sorry, I missed adding Daniel Braunwarth.

Please also note that this is essentially a rewrite of Daniels patch merged during the previous merge window, thus I think it makes sense for net-next rather than net. It may be appropriate to be backported to stable at a later date.

Quoted 350 lines · Russell King (Oracle)

Implement Wake-on-Lan for RTL8211F correctly. The existing implementation has multiple issues:

1. It assumes that Wake-on-Lan can always be used, whether or not the interrupt is wired, and whether or not the interrupt is capable of waking the system. This breaks the ability for MAC drivers to detect whether the PHY WoL is functional.
2. switching the interrupt pin in the .set_wol() method to PMEB mode immediately silences link-state interrupts, which breaks phylib when interrupts are being used rather than polling mode.
3. the code claiming to "reset WOL status" was doing nothing of the sort. Bit 15 in page 0xd8a register 17 controls WoL reset, and needs to be pulsed low to reset the WoL state. This bit was always written as '1', resulting in no reset.
4. not resetting WoL state results in the PMEB pin remaining asserted, which in turn leads to an interrupt storm. Only resetting the WoL state in .set_wol() is not sufficient.
5. PMEB mode does not allow software detection of the wake-up event as there is no status bit to indicate we received the WoL packet.
6. across reboots of at least the Jetson Xavier NX system, the WoL configuration is preserved.

Fix all of these issues by essentially rewriting the support. We:
1. clear the WoL event enable register at probe time.
2. detect whether we can support wake-up by having a valid interrupt, and the "wakeup-source" property in DT. If we can, then we mark the MDIO device as wakeup capable, and associate the interrupt with the wakeup source.
3. arrange for the get_wol() and set_wol() implementations to handle the case where the MDIO device has not been marked as wakeup capable (thereby returning no WoL support, and refusing to enable WoL support.)
4. avoid switching to PMEB mode, instead using INTB mode with the interrupt enable, reconfiguring the interrupt enables at suspend time, and restoring their original state at resume time (we track the state of the interrupt enable register in .config_intr() register.)
5. move WoL reset from .set_wol() to the suspend function to ensure that WoL state is cleared prior to suspend. This is necessary after the PME interrupt has been enabled as a second WoL packet will not re-raise a previously cleared PME interrupt.
6. when a PME interrupt (for wakeup) is asserted, pass this to the PM wakeup so it knows which device woke the system.

This fixes WoL support in the Realtek RTL8211F driver when used on the nVidia Jetson Xavier NX platform, and needs to be applied before stmmac patches which allow these platforms to forward the ethtool WoL commands to the Realtek PHY.

---
 drivers/net/phy/realtek/realtek_main.c | 172 ++++++++++++++++++++-----
 1 file changed, 140 insertions(+), 32 deletions(-)
drivers/net/phy/realtek/realtek_main.c +140 -32
index dd0d675149ad..4361529e68fb 100644
@@ -10,6 +10,7 @@
 #include <linux/bitops.h>
 #include <linux/of.h>
 #include <linux/phy.h>
+#include <linux/pm_wakeirq.h>
 #include <linux/netdevice.h>
 #include <linux/module.h>
 #include <linux/delay.h>
@@ -31,6 +32,7 @@
 #define RTL821x_INER				0x12
 #define RTL8211B_INER_INIT			0x6400
 #define RTL8211E_INER_LINK_STATUS		BIT(10)
+#define RTL8211F_INER_PME			BIT(7)
 #define RTL8211F_INER_LINK_STATUS		BIT(4)
 
 #define RTL821x_INSR				0x13
@@ -96,17 +98,13 @@
 #define RTL8211F_RXCR				0x15
 #define RTL8211F_RX_DELAY			BIT(3)
 
-/* RTL8211F WOL interrupt configuration */
-#define RTL8211F_INTBCR_PAGE			0xd40
-#define RTL8211F_INTBCR				0x16
-#define RTL8211F_INTBCR_INTB_PMEB		BIT(5)
-
 /* RTL8211F WOL settings */
-#define RTL8211F_WOL_SETTINGS_PAGE		0xd8a
+#define RTL8211F_WOL_PAGE		0xd8a
 #define RTL8211F_WOL_SETTINGS_EVENTS		16
 #define RTL8211F_WOL_EVENT_MAGIC		BIT(12)
-#define RTL8211F_WOL_SETTINGS_STATUS		17
-#define RTL8211F_WOL_STATUS_RESET		(BIT(15) | 0x1fff)
+#define RTL8211F_WOL_RST_RMSQ		17
+#define RTL8211F_WOL_RG_RSTB			BIT(15)
+#define RTL8211F_WOL_RMSQ			0x1fff
 
 /* RTL8211F Unique phyiscal and multicast address (WOL) */
 #define RTL8211F_PHYSICAL_ADDR_PAGE		0xd8c
@@ -172,7 +170,8 @@ struct rtl821x_priv {
 	u16 phycr2;
 	bool has_phycr2;
 	struct clk *clk;
-	u32 saved_wolopts;
+	/* rtl8211f */
+	u16 iner;
 };
 
 static int rtl821x_read_page(struct phy_device *phydev)
@@ -255,6 +254,34 @@ static int rtl821x_probe(struct phy_device *phydev)
 	return 0;
 }
 
+static int rtl8211f_probe(struct phy_device *phydev)
+{
+	struct device *dev = &phydev->mdio.dev;
+	int ret;
+
+	ret = rtl821x_probe(phydev);
+	if (ret < 0)
+		return ret;
+
+	/* Disable all PME events */
+	ret = phy_write_paged(phydev, RTL8211F_WOL_PAGE,
+			      RTL8211F_WOL_SETTINGS_EVENTS, 0);
+	if (ret < 0)
+		return ret;
+
+	/* Mark this PHY as wakeup capable and register the interrupt as a
+	 * wakeup IRQ if the PHY is marked as a wakeup source in firmware,
+	 * and the interrupt is valid.
+	 */
+	if (device_property_read_bool(dev, "wakeup-source") &&
+	    phy_interrupt_is_valid(phydev)) {
+		device_set_wakeup_capable(dev, true);
+		devm_pm_set_wake_irq(dev, phydev->irq);
+	}
+
+	return ret;
+}
+
 static int rtl8201_ack_interrupt(struct phy_device *phydev)
 {
 	int err;
@@ -352,6 +379,7 @@ static int rtl8211e_config_intr(struct phy_device *phydev)
 
 static int rtl8211f_config_intr(struct phy_device *phydev)
 {
+	struct rtl821x_priv *priv = phydev->priv;
 	u16 val;
 	int err;
 
@@ -362,8 +390,10 @@ static int rtl8211f_config_intr(struct phy_device *phydev)
 
 		val = RTL8211F_INER_LINK_STATUS;
 		err = phy_write_paged(phydev, 0xa42, RTL821x_INER, val);
+		if (err == 0)
+			priv->iner = val;
 	} else {
-		val = 0;
+		priv->iner = val = 0;
 		err = phy_write_paged(phydev, 0xa42, RTL821x_INER, val);
 		if (err)
 			return err;
@@ -426,21 +456,34 @@ static irqreturn_t rtl8211f_handle_interrupt(struct phy_device *phydev)
 		return IRQ_NONE;
 	}
 
-	if (!(irq_status & RTL8211F_INER_LINK_STATUS))
-		return IRQ_NONE;
+	if (irq_status & RTL8211F_INER_LINK_STATUS) {
+		phy_trigger_machine(phydev);
+		return IRQ_HANDLED;
+	}
 
-	phy_trigger_machine(phydev);
+	if (irq_status & RTL8211F_INER_PME) {
+		pm_wakeup_event(&phydev->mdio.dev, 0);
+		return IRQ_HANDLED;
+	}
 
-	return IRQ_HANDLED;
+	return IRQ_NONE;
 }
 
 static void rtl8211f_get_wol(struct phy_device *dev, struct ethtool_wolinfo *wol)
 {
 	int wol_events;
 
+	/* If the PHY is not capable of waking the system, then WoL can not
+	 * be supported.
+	 */
+	if (!device_can_wakeup(&dev->mdio.dev)) {
+		wol->supported = 0;
+		return;
+	}
+
 	wol->supported = WAKE_MAGIC;
 
-	wol_events = phy_read_paged(dev, RTL8211F_WOL_SETTINGS_PAGE, RTL8211F_WOL_SETTINGS_EVENTS);
+	wol_events = phy_read_paged(dev, RTL8211F_WOL_PAGE, RTL8211F_WOL_SETTINGS_EVENTS);
 	if (wol_events < 0)
 		return;
 
@@ -453,6 +496,9 @@ static int rtl8211f_set_wol(struct phy_device *dev, struct ethtool_wolinfo *wol)
 	const u8 *mac_addr = dev->attached_dev->dev_addr;
 	int oldpage;
 
+	if (!device_can_wakeup(&dev->mdio.dev))
+		return -EOPNOTSUPP;
+
 	oldpage = phy_save_page(dev);
 	if (oldpage < 0)
 		goto err;
@@ -464,25 +510,23 @@ static int rtl8211f_set_wol(struct phy_device *dev, struct ethtool_wolinfo *wol)
 		__phy_write(dev, RTL8211F_PHYSICAL_ADDR_WORD1, mac_addr[3] << 8 | (mac_addr[2]));
 		__phy_write(dev, RTL8211F_PHYSICAL_ADDR_WORD2, mac_addr[5] << 8 | (mac_addr[4]));
 
-		/* Enable magic packet matching and reset WOL status */
-		rtl821x_write_page(dev, RTL8211F_WOL_SETTINGS_PAGE);
+		/* Enable magic packet matching */
+		rtl821x_write_page(dev, RTL8211F_WOL_PAGE);
 		__phy_write(dev, RTL8211F_WOL_SETTINGS_EVENTS, RTL8211F_WOL_EVENT_MAGIC);
-		__phy_write(dev, RTL8211F_WOL_SETTINGS_STATUS, RTL8211F_WOL_STATUS_RESET);
-
-		/* Enable the WOL interrupt */
-		rtl821x_write_page(dev, RTL8211F_INTBCR_PAGE);
-		__phy_set_bits(dev, RTL8211F_INTBCR, RTL8211F_INTBCR_INTB_PMEB);
+		/* Set the maximum packet size, and assert WoL reset */
+		__phy_write(dev, RTL8211F_WOL_RST_RMSQ, RTL8211F_WOL_RMSQ);
 	} else {
-		/* Disable the WOL interrupt */
-		rtl821x_write_page(dev, RTL8211F_INTBCR_PAGE);
-		__phy_clear_bits(dev, RTL8211F_INTBCR, RTL8211F_INTBCR_INTB_PMEB);
-
-		/* Disable magic packet matching and reset WOL status */
-		rtl821x_write_page(dev, RTL8211F_WOL_SETTINGS_PAGE);
+		/* Disable magic packet matching */
+		rtl821x_write_page(dev, RTL8211F_WOL_PAGE);
 		__phy_write(dev, RTL8211F_WOL_SETTINGS_EVENTS, 0);
-		__phy_write(dev, RTL8211F_WOL_SETTINGS_STATUS, RTL8211F_WOL_STATUS_RESET);
+
+		/* Place WoL in reset */
+		__phy_clear_bits(dev, RTL8211F_WOL_RST_RMSQ,
+				 RTL8211F_WOL_RG_RSTB);
 	}
 
+	device_set_wakeup_enable(&dev->mdio.dev, !!(wol->wolopts & WAKE_MAGIC));
+
 err:
 	return phy_restore_page(dev, oldpage, 0);
 }
@@ -628,6 +672,52 @@ static int rtl821x_suspend(struct phy_device *phydev)
 	return ret;
 }
 
+static int rtl8211f_suspend(struct phy_device *phydev)
+{
+	u16 wol_rst;
+	int ret;
+
+	ret = rtl821x_suspend(phydev);
+	if (ret < 0)
+		return ret;
+
+	/* If a PME event is enabled, then configure the interrupt for
+	 * PME events only, disabling link interrupt. We avoid switching
+	 * to PMEB mode as we don't have a status bit for that.
+	 */
+	if (device_may_wakeup(&phydev->mdio.dev)) {
+		ret = phy_write_paged(phydev, 0xa42, RTL821x_INER,
+				      RTL8211F_INER_PME);
+		if (ret < 0)
+			goto err;
+
+		/* Read the INSR to clear any pending interrupt */
+		phy_read_paged(phydev, RTL8211F_INSR_PAGE, RTL8211F_INSR);
+
+		/* Reset the WoL to ensure that an event is picked up.
+		 * Unless we do this, even if we receive another packet,
+		 * we may not have a PME interrupt raised.
+		 */
+		ret = phy_read_paged(phydev, RTL8211F_WOL_PAGE,
+				     RTL8211F_WOL_RST_RMSQ);
+		if (ret < 0)
+			goto err;
+
+		wol_rst = ret & ~RTL8211F_WOL_RG_RSTB;
+		ret = phy_write_paged(phydev, RTL8211F_WOL_PAGE,
+				      RTL8211F_WOL_RST_RMSQ, wol_rst);
+		if (ret < 0)
+			goto err;
+
+		wol_rst |= RTL8211F_WOL_RG_RSTB;
+		ret = phy_write_paged(phydev, RTL8211F_WOL_PAGE,
+				      RTL8211F_WOL_RST_RMSQ, wol_rst);
+	}
+
+err:
+	return ret;
+}
+
 static int rtl821x_resume(struct phy_device *phydev)
 {
 	struct rtl821x_priv *priv = phydev->priv;
@@ -645,6 +735,24 @@ static int rtl821x_resume(struct phy_device *phydev)
 	return 0;
 }
 
+static int rtl8211f_resume(struct phy_device *phydev)
+{
+	struct rtl821x_priv *priv = phydev->priv;
+	int ret;
+
+	ret = rtl821x_resume(phydev);
+	if (ret < 0)
+		return ret;
+
+	/* If the device was programmed for a PME event, restore the interrupt
+	 * enable so phylib can receive link state interrupts.
+	 */
+	if (device_may_wakeup(&phydev->mdio.dev))
+		ret = phy_write_paged(phydev, 0xa42, RTL821x_INER, priv->iner);
+
+	return ret;
+}
+
 static int rtl8211x_led_hw_is_supported(struct phy_device *phydev, u8 index,
 					unsigned long rules)
 {
@@ -1612,15 +1720,15 @@ static struct phy_driver realtek_drvs[] = {
 	}, {
 		PHY_ID_MATCH_EXACT(0x001cc916),
 		.name		= "RTL8211F Gigabit Ethernet",
-		.probe		= rtl821x_probe,
+		.probe		= rtl8211f_probe,
 		.config_init	= &rtl8211f_config_init,
 		.read_status	= rtlgen_read_status,
 		.config_intr	= &rtl8211f_config_intr,
 		.handle_interrupt = rtl8211f_handle_interrupt,
 		.set_wol	= rtl8211f_set_wol,
 		.get_wol	= rtl8211f_get_wol,
-		.suspend	= rtl821x_suspend,
-		.resume		= rtl821x_resume,
+		.suspend	= rtl8211f_suspend,
+		.resume		= rtl8211f_resume,
 		.read_page	= rtl821x_read_page,
 		.write_page	= rtl821x_write_page,
 		.flags		= PHY_ALWAYS_CALL_SUSPEND,
Signature · 1 line
2.30.2
Signature · 2 lines
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 80Mbps down 10Mbps up. Decent connectivity at last!
#2 lore raw

PATCH 1/1 dt-bindings: net: realtek,rtl82xx: document wakeup-source property

In reply to Russell King (Oracle)

The RTL8211F PHY has two modes for a single INTB/PMEB pin:

1. INTB mode, where it signals interrupts to the CPU, which can include wake-on-LAN events.
2. PMEB mode, where it only signals a wake-on-LAN event, which may either be a latched logic low until software manually clears the WoL state, or pulsed mode.

In the case of (1), there is no way to know whether the interrupt to which the PHY is connected is capable of waking the system. In the case of (2), there would be no interrupt property in the PHY's DT description, and thus there is nothing to describe whether the pin is even wired to anything such as a power management controller.

There is a "wakeup-source" property which can be applied to any device
- see Documentation/devicetree/bindings/power/wakeup-source.txt

Case 1 above matches example 2 in this document, and case 2 above matches example 3. Therefore, it seems reasonable to make use of this existing specification, albiet it hasn't been converted to YAML.

Document the wakeup-source property in the device description, which will indicate that the PHY has been wired up in such a way that it can wake the system from a low power state.

We will use this in a rewrite of the existing broken Wake-on-Lan code that was merged during the 6.16 merge window to support case 1. Case 2 can be added to the driver later without needing to further alter the DT description. To be clear, the existing Wake-on-Lan code that was recently merged has multiple functional issues.

---
Apologies, this should've been sent with the patch to the driver which can be found at:

https://lore.kernel.org/r/[email protected]

 Documentation/devicetree/bindings/net/realtek,rtl82xx.yaml | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)
Documentation/devicetree/bindings/net/realtek,rtl82xx.yaml +5 -1
index d248a08a2136..2b5697bd7c5d 100644
@@ -45,12 +45,16 @@ title: Realtek RTL82xx PHY
     description:
       Disable CLKOUT clock, CLKOUT clock default is enabled after hardware reset.
 
-
   realtek,aldps-enable:
     type: boolean
     description:
       Enable ALDPS mode, ALDPS mode default is disabled after hardware reset.
 
+  wakeup-source:
+    type: boolean
+    description:
+      Enable Wake-on-LAN support for the RTL8211F PHY.
+
 unevaluatedProperties: false
 
 allOf:
Signature · 1 line
2.30.2
Acked-by on v1 1/1
#3 lore raw

Re: [PATCH net-next] dt-bindings: net: realtek,rtl82xx: document wakeup-source property

Quoted 31 lines · Russell King (Oracle)

The RTL8211F PHY has two modes for a single INTB/PMEB pin:

1. INTB mode, where it signals interrupts to the CPU, which can include wake-on-LAN events.
2. PMEB mode, where it only signals a wake-on-LAN event, which may either be a latched logic low until software manually clears the WoL state, or pulsed mode.

In the case of (1), there is no way to know whether the interrupt to which the PHY is connected is capable of waking the system. In the case of (2), there would be no interrupt property in the PHY's DT description, and thus there is nothing to describe whether the pin is even wired to anything such as a power management controller.

There is a "wakeup-source" property which can be applied to any device
- see Documentation/devicetree/bindings/power/wakeup-source.txt

Case 1 above matches example 2 in this document, and case 2 above matches example 3. Therefore, it seems reasonable to make use of this existing specification, albiet it hasn't been converted to YAML.

Document the wakeup-source property in the device description, which will indicate that the PHY has been wired up in such a way that it can wake the system from a low power state.

We will use this in a rewrite of the existing broken Wake-on-Lan code that was merged during the 6.16 merge window to support case 1. Case 2 can be added to the driver later without needing to further alter the DT description. To be clear, the existing Wake-on-Lan code that was recently merged has multiple functional issues.

Quoted 6 lines

---
Apologies, this should've been sent with the patch to the driver which can be found at:

https://lore.kernel.org/r/[email protected]

Quoted 29 lines
 Documentation/devicetree/bindings/net/realtek,rtl82xx.yaml | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)
Documentation/devicetree/bindings/net/realtek,rtl82xx.yaml +5 -1
index d248a08a2136..2b5697bd7c5d 100644
@@ -45,12 +45,16 @@ title: Realtek RTL82xx PHY
     description:
       Disable CLKOUT clock, CLKOUT clock default is enabled after hardware reset.
 
-
   realtek,aldps-enable:
     type: boolean
     description:
       Enable ALDPS mode, ALDPS mode default is disabled after hardware reset.
 
+  wakeup-source:
+    type: boolean
+    description:
+      Enable Wake-on-LAN support for the RTL8211F PHY.
+
 unevaluatedProperties: false
 
 allOf:
Signature · 1 line
2.30.2
#4 lore raw

Re: [PATCH net-next] dt-bindings: net: realtek,rtl82xx: document wakeup-source property

In reply to Russell King (Oracle)
This patch was applied to netdev/net-next.git (main) by Jakub Kicinski <[email protected]>:

Hello:

This patch was applied to netdev/net-next.git (main) by Jakub Kicinski <[email protected]>:

Quoted 9 lines · On Wed, 13 Aug 2025 12:21:19 +0100 you wrote:

The RTL8211F PHY has two modes for a single INTB/PMEB pin:

1. INTB mode, where it signals interrupts to the CPU, which can include wake-on-LAN events.
2. PMEB mode, where it only signals a wake-on-LAN event, which may either be a latched logic low until software manually clears the WoL state, or pulsed mode.

[...]

Here is the summary with links:
- [net-next] dt-bindings: net: realtek,rtl82xx: document wakeup-source property

    https://git.kernel.org/netdev/net-next/c/a510980e740c

You are awesome, thank you!

Signature · 2 lines
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html
#5 lore raw
In reply to Russell King (Oracle)

drivers/net/phy/realtek/realtek_main.c static int rtl821x_probe(struct phy_device *phydev) · line 280

Quoted 9 lines · Russell King (Oracle)
drivers/net/phy/realtek/realtek_main.c +9 -0
+	/* Mark this PHY as wakeup capable and register the interrupt as a
+	 * wakeup IRQ if the PHY is marked as a wakeup source in firmware,
+	 * and the interrupt is valid.
+	 */
+	if (device_property_read_bool(dev, "wakeup-source") &&
+	    phy_interrupt_is_valid(phydev)) {
+		device_set_wakeup_capable(dev, true);
+		devm_pm_set_wake_irq(dev, phydev->irq);
+	}

I'm wondering whether this should just check for the "wakeup-source" property, which would allow for PMEB mode, and if we don't have a valid interrupt, we set the INTB/PMEB pin to PMEB mode here. In other words:

	if (device_property_read_bool(dev, "wakeup-source")) {
		device_set_wakeup_capable(dev, true);
		if (phy_interrupt_is_valid(phydev)) {
			devm_pm_set_wake_irq(dev, phydev->irq);
		} else {
			ret = phy_modify_paged(phydev, RTL8211F_INTBCR_PAGE,
					       RTL8211F_INTBCR,
					       RTL8211F_INTBCR_INTB_PMEB,
					       RTL8211F_INTBCR_INTB_PMEB);
		}
	}

this would support example 3 in the wakeup-source document, where the PHY is connected to an interrupt-less power management controller.

Any thoughts?

Signature · 2 lines
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 80Mbps down 10Mbps up. Decent connectivity at last!
maintainer Reviewed-by
#6 lore raw
Quoted 27 lines · Russell King (Oracle)

drivers/net/phy/realtek/realtek_main.c static int rtl821x_probe(struct phy_device *phydev) · line 280

Quoted 9 lines · Russell King (Oracle)
drivers/net/phy/realtek/realtek_main.c +9 -0
+	/* Mark this PHY as wakeup capable and register the interrupt as a
+	 * wakeup IRQ if the PHY is marked as a wakeup source in firmware,
+	 * and the interrupt is valid.
+	 */
+	if (device_property_read_bool(dev, "wakeup-source") &&
+	    phy_interrupt_is_valid(phydev)) {
+		device_set_wakeup_capable(dev, true);
+		devm_pm_set_wake_irq(dev, phydev->irq);
+	}

I'm wondering whether this should just check for the "wakeup-source" property, which would allow for PMEB mode, and if we don't have a valid interrupt, we set the INTB/PMEB pin to PMEB mode here. In other words:

	if (device_property_read_bool(dev, "wakeup-source")) {
		device_set_wakeup_capable(dev, true);
		if (phy_interrupt_is_valid(phydev)) {
			devm_pm_set_wake_irq(dev, phydev->irq);
		} else {
			ret = phy_modify_paged(phydev, RTL8211F_INTBCR_PAGE,
					       RTL8211F_INTBCR,
					       RTL8211F_INTBCR_INTB_PMEB,
					       RTL8211F_INTBCR_INTB_PMEB);
		}
	}
Quoted 4 lines

this would support example 3 in the wakeup-source document, where the PHY is connected to an interrupt-less power management controller.

Any thoughts?

I guess you have no way to actually test it?

I would probably not support it now. When somebody actually needs it, this email exists, it points out how to do it.

Andrew

#7 lore raw
In reply to Russell King (Oracle)
This patch was applied to netdev/net-next.git (main) by Jakub Kicinski <[email protected]>:

Hello:

This patch was applied to netdev/net-next.git (main) by Jakub Kicinski <[email protected]>:

Quoted 22 lines · On Wed, 13 Aug 2025 11:04:45 +0100 you wrote:

Implement Wake-on-Lan for RTL8211F correctly. The existing implementation has multiple issues:

1. It assumes that Wake-on-Lan can always be used, whether or not the interrupt is wired, and whether or not the interrupt is capable of waking the system. This breaks the ability for MAC drivers to detect whether the PHY WoL is functional.
2. switching the interrupt pin in the .set_wol() method to PMEB mode immediately silences link-state interrupts, which breaks phylib when interrupts are being used rather than polling mode.
3. the code claiming to "reset WOL status" was doing nothing of the sort. Bit 15 in page 0xd8a register 17 controls WoL reset, and needs to be pulsed low to reset the WoL state. This bit was always written as '1', resulting in no reset.
4. not resetting WoL state results in the PMEB pin remaining asserted, which in turn leads to an interrupt storm. Only resetting the WoL state in .set_wol() is not sufficient.
5. PMEB mode does not allow software detection of the wake-up event as there is no status bit to indicate we received the WoL packet.
6. across reboots of at least the Jetson Xavier NX system, the WoL configuration is preserved.

Quoted 1 line

[...]

Here is the summary with links:
- [net-next] net: phy: realtek: fix RTL8211F wake-on-lan support

    https://git.kernel.org/netdev/net-next/c/b826bf795564

You are awesome, thank you!

Signature · 2 lines
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html