Skip to contentSkip to conversation

2.6.9-rc2-mm2: 3ware card info not in /proc/scsi

DISCUSSION Adam Radford 3 participants 3 messages Sep 23, 2004 – Sep 24, 2004

lore
Share & tools
lore
#0 lore raw

Glenn,

The /proc/scsi interface is being deprecated by the SCSI subsystem maintainers.

Support for /proc/scsi/3w-xxxx has been removed from the driver and sysfs support has been added. Please download the newer 3dm2 tools from the 3ware software "In-Engineering Development" website, or, keep your older kernel and tools.

If you have any more questions, please contact 3ware/AMCC support.

-Adam

-----Original Message-----
From: [email protected] [mailto:[email protected]]On Behalf Of Glenn Johnson
Sent: Thursday, September 23, 2004 9:09 AM
To: [email protected]
Subject: 2.6.9-rc2-mm2: 3ware card info not in /proc/scsi

I have a 3Ware-7500 series card. I was trying the 2.6.9-rc2-mm2 kernel and discovered that the 3dmd utility was not working. A little poking around revealed that the cause was because the 3Ware directory was not in /proc/scsi, even though I have CONFIG_SCSI_PROC_FS=y in my config file. The 3dmd utility works fine with mainline 2.6.9-rc2 and it worked with the 2.6.8-mm series of kernels. Those kernels have a 3w-xxxx directory in /proc/scsi.

Thanks.

Signature · 7 lines
Glenn Johnson

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/
#1 lore raw
Quoted 3 lines · Adam Radford

Glenn,

The /proc/scsi interface is being deprecated by the SCSI subsystem maintainers.

I am aware of that. I also thought the interface would remain until third party vendors had a chance to catch up.

Quoted 2 lines

Support for /proc/scsi/3w-xxxx has been removed from the driver and sysfs support has been added.

Is is possible to have it support both?

Quoted 2 lines

Please download the newer 3dm2 tools from the 3ware software "In-Engineering Development" website, or, keep your older kernel and tools.

I am not sure what the "In-Engineering Development" website is but the "regular" 3ware Web site only offers 3dm2 for the 9000 series controllers, which I do not have. I suppose I could just try it though.

Quoted 1 line

If you have any more questions, please contact 3ware/AMCC support.

I do not know what AMCC brings to the table but I have never gotten answers from 3Ware support.

Quoted 19 lines

-Adam

-----Original Message-----
From: [email protected] [mailto:[email protected]]On Behalf Of Glenn Johnson
Sent: Thursday, September 23, 2004 9:09 AM
To: [email protected]
Subject: 2.6.9-rc2-mm2: 3ware card info not in /proc/scsi

I have a 3Ware-7500 series card. I was trying the 2.6.9-rc2-mm2 kernel and discovered that the 3dmd utility was not working. A little poking around revealed that the cause was because the 3Ware directory was not in /proc/scsi, even though I have CONFIG_SCSI_PROC_FS=y in my config file. The 3dmd utility works fine with mainline 2.6.9-rc2 and it worked with the 2.6.8-mm series of kernels. Those kernels have a 3w-xxxx directory in /proc/scsi.

Thanks.

Signature · 1 line
Glenn Johnson
#2 lore raw
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line

"GJ" == Glenn Johnson <[email protected]> writes:

GJ> I am not sure what the "In-Engineering Development" website is but GJ> the "regular" 3ware Web site only offers 3dm2 for the 9000 series GJ> controllers, which I do not have.

Try: http://www.3ware.com/support/downloadnew.asp

GJ> I do not know what AMCC brings to the table but I have never GJ> gotten answers from 3Ware support.

I've gotten pretty good support from them; they've even called me to check up after I reported problems on a mailing list ([email protected]).

- J<