2.6.9-rc2-mm2: 3ware card info not in /proc/scsi
Glenn,
proc_info support is being removed from scsi drivers _right now_. There are other instances of this happening:
http://marc.theaimsgroup.com/?l=bk-commits-head&m=109372835112734&w=2
Furthermore, no changes to this interface are being accepted.
This probably should have happened in 2.7, but there is no 2.7 tree, as 2.6.8.1 is the stable kernel and -mm is the development tree.
There was so much dead code in the 3w-xxxx driver that it needed a major facelift for 2.6. Otherwise it would eventually have been marked broken. As a part of the facelift, you must update your tools. Nobody can guarantee future proofness of userspace tools that access low level kernel ioctls, /proc entries, /sysfs entries, etc. As the kernel changes, drivers change, and therefore userspace tools also change. If you don't want to upgrade your tools, don't upgrade your kernel. The driver changes in the -mm tree are not likely to make it into the mainline till 2.6.10 final. In the meantime you can run 2.6.8.1 or drop the changes for 3w-xxxx from the -mm patch if you really need to run it.
3dm2 and the new tw_cli also support 7000 & 8000 controllers, however you need the In-Engineering Developement (Pre 9.1) tools release since they do part of their controller detection through the new sysfs attributes in the newer 3w-xxxx driver. If you don't want to get the pre-release tools, wait till the 9.1 release comes out, and the 3dm2 and tw_cli in that release will work for you.
-Adam
Quoted 73 lines
-----Original Message-----
From: [email protected] [mailto:[email protected]]On Behalf Of Glenn Johnson
Sent: Thursday, September 23, 2004 10:55 AM
To: Adam Radford
Cc: [email protected]
Subject: RE: 2.6.9-rc2-mm2: 3ware card info not in/proc/scsiQuoted 3 lines · Adam Radford
Glenn,
The
/proc/scsiinterface is being deprecated by the SCSIsubsystem maintainers.
I am aware of that. I also thought the interface would remain until third party vendors had a chance to catch up.
Quoted 1 line
Support for
/proc/scsi/3w-xxxxhas been removed from thedriver and sysfs support
Quoted 1 line
has been added.
Is is possible to have it support both?
Quoted 2 lines
Please download the newer 3dm2 tools from the 3ware software "In-Engineering Development" website, or, keep your older
kernel and tools.
I am not sure what the "In-Engineering Development" website is but the "regular" 3ware Web site only offers 3dm2 for the 9000 series controllers, which I do not have. I suppose I could just try it though.
Quoted 1 line
If you have any more questions, please contact 3ware/AMCC support.
I do not know what AMCC brings to the table but I have never gotten answers from 3Ware support.
Quoted 5 lines
-Adam
-----Original Message-----
From: [email protected] [mailto:[email protected]]On Behalf OfGlenn Johnson
Quoted 6 lines
Sent: Thursday, September 23, 2004 9:09 AM
To: [email protected]
Subject: 2.6.9-rc2-mm2: 3ware card info not in/proc/scsiI have a 3Ware-7500 series card. I was trying the
2.6.9-rc2-mm2 kernel
Quoted 1 line
and discovered that the 3dmd utility was not working. A
little poking
Quoted 1 line
around revealed that the cause was because the 3Ware
directory was not
Quoted 2 lines
in
/proc/scsi, even though I haveCONFIG_SCSI_PROC_FS=yin my config file. The 3dmd utility works fine with mainline 2.6.9-rc2and it worked
Quoted 4 lines
with the 2.6.8-mm series of kernels. Those kernels have a 3w-xxxx directory in
/proc/scsi.Thanks.
Signature · 8 lines
Glenn Johnson - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
Quoted 5 lines · Adam Radford
There was so much dead code in the 3w-xxxx driver that it needed a major facelift for 2.6. Otherwise it would eventually have been marked broken. As a part of the facelift, you must update your tools. Nobody can guarantee future proofness of userspace tools that access low level kernel ioctls, /proc entries, /sysfs entries, etc.
Sure but thats a lot easier to manage when source code is available.