Skip to contentSkip to conversation

#raspberrypi

yocto Khem Raj 3 participants 4 messages Dec 17, 2019 2 messages not in the archive

lore
Share & tools
lore

A message that is not in the archive (sent off-list or not yet received): [email protected]

Khem Raj

author
#1 lore raw
Quoted 20 lines · On Mon, Dec 16, 2019 at 1:56 PM <[email protected]> wrote:

Problem with rootfs boot on my raspberrypi.

Hi
I am building simple image for my raspbery pi 3 A+ and connect to the pi via USB-UART converter and see the following in the console
...

[ 2.071459] Run /bin/init as init process
[ 2.076507] Run /bin/sh as init process

sh: cannot set terminal process group (-1): Inappropriate ioctl for device
sh: no job control in this shell
sh-4.4#

I build with the "bitbake core-image-base" and tried to run it on rpi 3A+, 3B, 3B+ and the problem is always the same it cannot switch to the rootfs on the sd card it seem like it stack at initramfs or some middle ground.

I burn the *.rpi-sdimg image to SD card with dd from my Ubuntu16.04 host machine.
I tried with two branches thud and warrior and the problem is exactly the same.
The strange thing is that in this initramfs there are no tools like find grep modprobe etc. but I see my extra tools "i2c-tools vim"

Quoted 5 lines

Here is my local.conf adjustments:
MACHINE ?= "raspberrypi3"
ENABLE_I2C = "1"
ENABLE_UART = "1"
IMAGE_INSTALL += "i2c-tools vim"

Can you turn this into
IMAGE_INSTALL_append = " i2c-tools vim"

Quoted 28 lines

and the bblayer.conf
BBLAYERS ?= " \
/media/dave/Develop/yoctopi/warrior/sources/poky/meta \
/media/dave/Develop/yoctopi/warrior/sources/poky/meta-poky \
/media/dave/Develop/yoctopi/warrior/sources/poky/meta-yocto-bsp \
/media/dave/Develop/yoctopi/warrior/sources/meta-openembedded/meta-oe \
/media/dave/Develop/yoctopi/warrior/sources/meta-raspberrypi \
"

I tried also to build with the deprecated image "bitbake rpi-basic-image" but then I did not get my extra tools "i2c-tools vim".

Anyone have any idea what can be wrong with my approach ?

Regards,

Wojciech

-=-=-=-=-=-=-=-=-=-=-=-
Links: You receive all messages sent to this group.

View/Reply Online (#47702): https://lists.yoctoproject.org/g/yocto/message/47702
Mute This Topic: https://lists.yoctoproject.org/mt/68744766/1997914
Mute #raspberrypi: https://lists.yoctoproject.org/mk?hashtag=raspberrypi&subid=6692173
Group Owner: [email protected]
Unsubscribe: https://lists.yoctoproject.org/g/yocto/unsub [[email protected]]
-=-=-=-=-=-=-=-=-=-=-=-

#2 lore raw

Hi Khem, Wojciech,

Quoted 21 lines · Khem Raj
Quoted 20 lines · On Mon, Dec 16, 2019 at 1:56 PM <[email protected]> wrote:

Problem with rootfs boot on my raspberrypi.

Hi
I am building simple image for my raspbery pi 3 A+ and connect to the pi via USB-UART converter and see the following in the console
...

[ 2.071459] Run /bin/init as init process
[ 2.076507] Run /bin/sh as init process

sh: cannot set terminal process group (-1): Inappropriate ioctl for device
sh: no job control in this shell
sh-4.4#

I build with the "bitbake core-image-base" and tried to run it on rpi 3A+, 3B, 3B+ and the problem is always the same it cannot switch to the rootfs on the sd card it seem like it stack at initramfs or some middle ground.

I burn the *.rpi-sdimg image to SD card with dd from my Ubuntu16.04 host machine.
I tried with two branches thud and warrior and the problem is exactly the same.
The strange thing is that in this initramfs there are no tools like find grep modprobe etc. but I see my extra tools "i2c-tools vim"

Quoted 23 lines
Quoted 5 lines

Here is my local.conf adjustments:
MACHINE ?= "raspberrypi3"
ENABLE_I2C = "1"
ENABLE_UART = "1"
IMAGE_INSTALL += "i2c-tools vim"

Can you turn this into
IMAGE_INSTALL_append = " i2c-tools vim"

Quoted 14 lines

and the bblayer.conf
BBLAYERS ?= " \
/media/dave/Develop/yoctopi/warrior/sources/poky/meta \
/media/dave/Develop/yoctopi/warrior/sources/poky/meta-poky \
/media/dave/Develop/yoctopi/warrior/sources/poky/meta-yocto-bsp \
/media/dave/Develop/yoctopi/warrior/sources/meta-openembedded/meta-oe \
/media/dave/Develop/yoctopi/warrior/sources/meta-raspberrypi \
"

I tried also to build with the deprecated image "bitbake rpi-basic-image" but then I did not get my extra tools "i2c-tools vim".

Anyone have any idea what can be wrong with my approach ?

Strange enough, I had the same behaviour a couple of days ago but I thought it was something on my setup. I built core-iage-full-cmdline on TOT, and systemd as init manager. The issue was due because adding "userland", bash was added due RDEPENDS to the image and busybox with all related tools was dropped. After removing bash from image, it works again - but I have not git-bisect to check which is the cause.

Regards,
Stefano

Quoted 24 lines
Quoted 24 lines

Regards,

Wojciech

-=-=-=-=-=-=-=-=-=-=-=-
Links: You receive all messages sent to this group.

View/Reply Online (#47702): https://lists.yoctoproject.org/g/yocto/message/47702
Mute This Topic: https://lists.yoctoproject.org/mt/68744766/1997914
Mute #raspberrypi: https://lists.yoctoproject.org/mk?hashtag=raspberrypi&subid=6692173
Group Owner: [email protected]
Unsubscribe: https://lists.yoctoproject.org/g/yocto/unsub [[email protected]]
-=-=-=-=-=-=-=-=-=-=-=-

-=-=-=-=-=-=-=-=-=-=-=-
Links: You receive all messages sent to this group.

View/Reply Online (#47712): https://lists.yoctoproject.org/g/yocto/message/47712
Mute This Topic: https://lists.yoctoproject.org/mt/68752649/3618551
Mute #raspberrypi: https://lists.yoctoproject.org/mk?hashtag=raspberrypi&subid=6692235
Group Owner: [email protected]
Unsubscribe: https://lists.yoctoproject.org/g/yocto/unsub [[email protected]]
-=-=-=-=-=-=-=-=-=-=-=-

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected]
=====================================================================
author
#3 lore raw
Quoted 58 lines · Stefano Babic

Hi Khem, Wojciech,

Quoted 6 lines · Khem Raj
Quoted 5 lines · On Mon, Dec 16, 2019 at 1:56 PM <[email protected]> wrote:

Problem with rootfs boot on my raspberrypi.

Hi
I am building simple image for my raspbery pi 3 A+ and connect to the

pi via USB-UART converter and see the following in the console

Quoted 4 lines
Quoted 4 lines

...

[ 2.071459] Run /bin/init as init process
[ 2.076507] Run /bin/sh as init process

sh: cannot set terminal process group (-1): Inappropriate ioctl for

device

Quoted 6 lines
Quoted 6 lines

sh: no job control in this shell
sh-4.4#

I build with the "bitbake core-image-base" and tried to run it on rpi

3A+, 3B, 3B+ and the problem is always the same it cannot switch to the rootfs on the sd card it seem like it stack at initramfs or some middle ground.

Quoted 2 lines
Quoted 2 lines

I burn the *.rpi-sdimg image to SD card with dd from my Ubuntu16.04

host machine.

Quoted 1 line
Quoted 1 line

I tried with two branches thud and warrior and the problem is exactly

the same.

Quoted 1 line
Quoted 1 line

The strange thing is that in this initramfs there are no tools like

find grep modprobe etc. but I see my extra tools "i2c-tools vim"

Quoted 17 lines
Quoted 6 lines

Here is my local.conf adjustments:
MACHINE ?= "raspberrypi3"
ENABLE_I2C = "1"
ENABLE_UART = "1"
IMAGE_INSTALL += "i2c-tools vim"

Can you turn this into
IMAGE_INSTALL_append = " i2c-tools vim"

Quoted 7 lines

and the bblayer.conf
BBLAYERS ?= " \
/media/dave/Develop/yoctopi/warrior/sources/poky/meta \
/media/dave/Develop/yoctopi/warrior/sources/poky/meta-poky \
/media/dave/Develop/yoctopi/warrior/sources/poky/meta-yocto-bsp \
/media/dave/Develop/yoctopi/warrior/sources/meta-openembedded/meta-oe

\

Quoted 4 lines
Quoted 4 lines
  /media/dave/Develop/yoctopi/warrior/sources/meta-raspberrypi \
  "

I tried also to build with the deprecated image "bitbake

rpi-basic-image" but then I did not get my extra tools "i2c-tools vim".

Quoted 3 lines
Quoted 3 lines

Anyone have any idea what can be wrong with my approach ?

Quoted 6 lines

Strange enough, I had the same behaviour a couple of days ago but I thought it was something on my setup. I built core-iage-full-cmdline on TOT, and systemd as init manager. The issue was due because adding "userland", bash was added due RDEPENDS to the image and busybox with all related tools was dropped. After removing bash from image, it works again - but I have not git-bisect to check which is the cause.

This would be a serious problem can you dive into it and see if we missed some Symlink

Quoted 44 lines

Regards,
Stefano

Quoted 9 lines
Quoted 9 lines

Regards,

Wojciech

-=-=-=-=-=-=-=-=-=-=-=-
Links: You receive all messages sent to this group.

View/Reply Online (#47702):

https://lists.yoctoproject.org/g/yocto/message/47702

Quoted 2 lines
Quoted 2 lines

Mute This Topic: https://lists.yoctoproject.org/mt/68744766/1997914
Mute #raspberrypi:

https://lists.yoctoproject.org/mk?hashtag=raspberrypi&subid=6692173

Quoted 2 lines
Quoted 2 lines

Group Owner: [email protected]
Unsubscribe: https://lists.yoctoproject.org/g/yocto/unsub [

[email protected]]

Quoted 6 lines
Quoted 6 lines

-=-=-=-=-=-=-=-=-=-=-=-

-=-=-=-=-=-=-=-=-=-=-=-
Links: You receive all messages sent to this group.

View/Reply Online (#47712):

https://lists.yoctoproject.org/g/yocto/message/47712

Quoted 2 lines
Quoted 2 lines

Mute This Topic: https://lists.yoctoproject.org/mt/68752649/3618551
Mute #raspberrypi:

https://lists.yoctoproject.org/mk?hashtag=raspberrypi&subid=6692235

Quoted 2 lines
Quoted 2 lines

Group Owner: [email protected]
Unsubscribe: https://lists.yoctoproject.org/g/yocto/unsub [

[email protected]]

Quoted 1 line
Quoted 1 line

-=-=-=-=-=-=-=-=-=-=-=-

--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected]
=====================================================================

A message that is not in the archive (sent off-list or not yet received): CAMKF1sqYnuJ_QY6uyw1jTrVwni=oeOECrtx7LJVvVFnEq3xsFA@mail.gmail.com-LwHB5UB----1

#5 lore raw

Hi Khem

Replacing
IMAGE_INSTALL += "i2c-tools vim"
withIMAGE_INSTALL_append = " i2c-tools vim"

in my local.conf solve the problem.

More than half of the sources were rebuild.

Thanks a lot.

Now I found also the info in the manual "Using IMAGE_INSTALL with the += operator from the /conf/local.conf file or from within an image recipe is not recommended as it can cause ordering issues."

Regards,

Wojciech

Signature · 5 lines
 Securely sent with Tutanota. Get your own encrypted, ad-free mailbox: 
 https://tutanota.com


Dec 17, 2019, 05:48 by [email protected]:
Quoted 61 lines · On Mon, Dec 16, 2019 at 1:56 PM <[email protected]> wrote:
Quoted 21 lines

Problem with rootfs boot on my raspberrypi.

Hi
I am building simple image for my raspbery pi 3 A+ and connect to the pi via USB-UART converter and see the following in the console
...

[ 2.071459] Run /bin/init as init process
[ 2.076507] Run /bin/sh as init process

sh: cannot set terminal process group (-1): Inappropriate ioctl for device
sh: no job control in this shell
sh-4.4#

I build with the "bitbake core-image-base" and tried to run it on rpi 3A+, 3B, 3B+ and the problem is always the same it cannot switch to the rootfs on the sd card it seem like it stack at initramfs or some middle ground.

I burn the *.rpi-sdimg image to SD card with dd from my Ubuntu16.04 host machine.
I tried with two branches thud and warrior and the problem is exactly the same.
The strange thing is that in this initramfs there are no tools like find grep modprobe etc. but I see my extra tools "i2c-tools vim"

Quoted 6 lines

Here is my local.conf adjustments:
MACHINE ?= "raspberrypi3"
ENABLE_I2C = "1"
ENABLE_UART = "1"
IMAGE_INSTALL += "i2c-tools vim"

Can you turn this into
IMAGE_INSTALL_append = " i2c-tools vim"

Quoted 29 lines

and the bblayer.conf
BBLAYERS ?= " \
/media/dave/Develop/yoctopi/warrior/sources/poky/meta \
/media/dave/Develop/yoctopi/warrior/sources/poky/meta-poky \
/media/dave/Develop/yoctopi/warrior/sources/poky/meta-yocto-bsp \
/media/dave/Develop/yoctopi/warrior/sources/meta-openembedded/meta-oe \
/media/dave/Develop/yoctopi/warrior/sources/meta-raspberrypi \
"

I tried also to build with the deprecated image "bitbake rpi-basic-image" but then I did not get my extra tools "i2c-tools vim".

Anyone have any idea what can be wrong with my approach ?

Regards,

Wojciech

-=-=-=-=-=-=-=-=-=-=-=-
Links: You receive all messages sent to this group.

View/Reply Online (#47702): https://lists.yoctoproject.org/g/yocto/message/47702
Mute This Topic: https://lists.yoctoproject.org/mt/68744766/1997914
Mute #raspberrypi: https://lists.yoctoproject.org/mk?hashtag=raspberrypi&subid=6692173
Group Owner: [email protected]
Unsubscribe: https://lists.yoctoproject.org/g/yocto/unsub [[email protected]]
-=-=-=-=-=-=-=-=-=-=-=-