Skip to contentSkip to conversation

harddisk suddenly locked?!

DISCUSSION Thomas Tanner 5 participants 5 messages Jul 31, 2001 – Aug 2, 2001

lore
Share & tools
lore
#0 lore raw

Please help me! I'm desperate

I can't access the data on my harddrive any longer ;-((

The IBM Disk Fitness Test tool tells me:

   Model                   : IBM-DJNA-372200
   Microcode level         : J71OA30K
   ATA Compliance          : ATA-4
  ...
   Settings
  ...
     S.M.A.R.T. status     : Good
     Security feature      : Supported
       Password            : Set
       Password level      : High
       Security mode       : Locked

However, I haven't set any password. I don't even know how to set it!! My system is (was) Linux 2.4.7 with PIIX support and "SCSI over IDE"
enabled,
experimental IDE code disabled.
After booting the system and leaving it one hour alone (idle, no internet
connection)
I wanted to start XWindows (4.01). However, it switched the video mode and
suddenly
locked up for ~10 sec. I pressed Ctrl-Alt-Backspace/Del several times to
reboot.
After some seconds it responded and seemed to shut down as usual. Since then the hd is locked and I don't know why.

According to the ATA-3 specification there are two passwords: a master and
a user password.
The passwords are stored in the EPROM of the hd and are certainly very very
hard to remove.
A locked drive rejects all media access commands.
When a new master password is set, the drive won't be locked. Setting a new user password locks the drive the next time it is powered-on. A drive can be unlocked by one of the two passwords.
IBM sets the master password to all ASCII blanks (0x20) during manufacturing.

To unlock a drive one has to send the command SECURITY UNLOCK (0xBB) and transfer a single sector to the drive:
Word
0 Bit 0 Identifier: 0=compare user password, 0=compare master password
1-16 Password (32 Bytes)
17-255 reserved

Word 128 of the Identify Drive command contains the Security status:
Bit
8 : Security level 0=High (can be unlocked), 1=Maximum (disk must be
erased)
4 : 1=Security count expired (more than five failed unlock tries,
hard-reset necessary)
3 : 1=Security frozen (all security commands aborted)
2 : 1=Security locked (media access not allowed)
1 : 1=Security enabled
0 : 1=Security supported

Something must have sent a lock command to my hd. Maybe a bug in the IDE
code?
I hope to be able to unlock my drive using the default master password. My question is: how can I send the unlock command to the hd? Is there any program that can do it?
AFAICS one can send only the command code using a HDIO_DRIVE_CMD ioctl. But how can I transfer the password?

Any ideas?

Thank you very much in advance!

PS: please CC to me

Thomas Tanner-------------------
tanner@(ffii.org|gnu.org|gmx.de)

#1 lore raw
Quoted 11 lines · Thomas Tanner

I can't access the data on my harddrive any longer ;-((

The IBM Disk Fitness Test tool tells me:

   Model                   : IBM-DJNA-372200
   Microcode level         : J71OA30K
   ATA Compliance          : ATA-4
     Security feature      : Supported
       Password            : Set
       Password level      : High
       Security mode       : Locked
Quoted 7 lines

However, I haven't set any password. I don't even know how to set it!! My system is (was) Linux 2.4.7 with PIIX support and "SCSI over IDE"
enabled,
I wanted to start XWindows (4.01). However, it switched the video mode and
suddenly locked up for ~10 sec. I pressed Ctrl-Alt-Backspace/Del
After some seconds it responded and seemed to shut down as usual. Since then the hd is locked and I don't know why.

Better shield your monitor?

Quoted 1 line

According to the ATA-3 specification

ATA-4 is also online.

Quoted 2 lines

To unlock a drive one has to send the command SECURITY UNLOCK (0xBB) and transfer a single sector to the drive:

Maybe someone has already done it. Otherwise you'll have to play a little with the code. It is easy. You could try to take setmax and hdparm as example and add an ioctl that combines HDIO_DRIVE_TASK and HDIO_DRIVE_CMD.

#2 lore raw
In reply to Thomas Tanner
Quoted 6 lines

A locked drive rejects all media access commands.
When a new master password is set, the drive won't be locked. Setting a new user password locks the drive the next time it is powered-on.

Something must have sent a lock command to my hd. Maybe a bug in the IDE
code?

Or someone broke into the box and did it. In fact given this feature is actually enabled on ibm disks Im amazed the windows viruses havent all started doing it

#3 lore raw
Quoted 3 lines · Alan Cox

Or someone broke into the box and did it. In fact given this feature is actually enabled on ibm disks Im amazed the windows viruses havent all started doing it

Destroying the bios is a bit more straightforward and certainly more universal.

-Dan

Signature · 1 line
[-] Omae no subete no kichi wa ore no mono da. [-]
#4 lore raw
Quoted 7 lines · Alan Cox
Quoted 3 lines

Or someone broke into the box and did it. In fact given this feature is actually enabled on ibm disks Im amazed the windows viruses havent all started doing it

Destroying the bios is a bit more straightforward and certainly more universal.

And a lot less damaging. Its "Oh dear put the disk in aother box and disinfect" not "oh god, all our web server data is lost"