riscv: asid: Fixup stale TLB entry cause application crash
PATCH RESEND 1/1 riscv: asid: Fixup stale TLB entry cause application crash
From: Guo Ren <[email protected]>
After use_asid_allocator enabled, the userspace application will crash for stale tlb entry. Because only using cpumask_clear_cpu without local_flush_tlb_all couldn't guarantee CPU's tlb entries fresh. Then set_mm_asid would cause user space application get a stale value by the stale tlb entry, but set_mm_noasid is okay.
Here is the symptom of the bug:
unhandled signal 11 code 0x1 (coredump)
0x0000003fd6d22524 <+4>: auipc s0,0x70 0x0000003fd6d22528 <+8>: ld s0,-148(s0) # 0x3fd6d92490 => 0x0000003fd6d2252c <+12>: ld a5,0(s0)
(gdb) i r s0
s0 0x8082ed1cc3198b21 0x8082ed1cc3198b21
(gdb) x/16 0x3fd6d924900x3fd6d92490: 0xd80ac8a8 0x0000003f
The core dump file shows that the value of register s0 is wrong, but the value in memory is right. This is because 'ld s0, -148(s0)' use a stale mapping entry in TLB and got a wrong value from a stale physical address.
When task run on CPU0, the task loaded/speculative-loaded the value of address(0x3fd6d92490), and the first version of tlb mapping entry was PTWed into CPU0's tlb.
When the task switched from CPU0 to CPU1 without local_tlb_flush_all (because of asid), the task happened to write a value on address (0x3fd6d92490). It caused do_page_fault -> wp_page_copy -> ptep_clear_flush -> ptep_get_and_clear & flush_tlb_page.
The flush_tlb_page used mm_cpumask(mm) to determine which CPUs need tlb flush, but CPU0 had cleared the CPU0's mm_cpumask in previous switch_mm. So we only flushed the CPU1 tlb, and setted second version mapping of the pte. When the task switch from CPU1 to CPU0 again, CPU0 still used a stale tlb mapping entry which contained a wrong target physical address. When the task happened to read that value, the bug would be raised.
--- arch/riscv/mm/context.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-)
arch/riscv/mm/context.c +3 -1
@@ -317,7 +317,9 @@ void switch_mm(struct mm_struct *prev, struct mm_struct *next,*/ cpu =smp_processor_id (); -cpumask_clear_cpu (cpu,mm_cpumask (prev)); +if (!static_branch_unlikely (&use_asid_allocator)) +cpumask_clear_cpu (cpu,mm_cpumask (prev)); +cpumask_set_cpu (cpu,mm_cpumask (next));set_mm (next, cpu);
Signature · 1 line
2.36.1
Quoted 50 lines · On 8 November 2022 10:20:44 GMT, [email protected] wrote:
From: Guo Ren <[email protected]>
After
use_asid_allocatorenabled, the userspace application will crash for stale tlb entry. Because only usingcpumask_clear_cpuwithoutlocal_flush_tlb_allcouldn't guarantee CPU's tlb entries fresh. Thenset_mm_asidwould cause user space application get a stale value by the stale tlb entry, butset_mm_noasidis okay.Here is the symptom of the bug:
unhandled signal 11 code0x1(coredump)0x0000003fd6d22524 <+4>: auipc s0,0x70 0x0000003fd6d22528 <+8>: ld s0,-148(s0) # 0x3fd6d92490=>
0x0000003fd6d2252c<+12>: ld a5,0(s0)
(gdb) i r s0
s00x8082ed1cc3198b210x8082ed1cc3198b21
(gdb) x/160x3fd6d924900x3fd6d92490:0xd80ac8a80x0000003f
The core dump file shows that the value of register s0 is wrong, but the value in memory is right. This is because 'ld s0, -148(s0)' use a stale mapping entry in TLB and got a wrong value from a stale physical address.When task run on CPU0, the task loaded/speculative-loaded the value of address(0x3fd6d92490), and the first version of tlb mapping entry was PTWed into CPU0's tlb.
When the task switched from CPU0 to CPU1 withoutlocal_tlb_flush_all(because of asid), the task happened to write a value on address (0x3fd6d92490). It causeddo_page_fault->wp_page_copy->ptep_clear_flush->ptep_get_and_clear&flush_tlb_page.
Theflush_tlb_pageusedmm_cpumask(mm)to determine which CPUs need tlb flush, but CPU0 had cleared the CPU0'smm_cpumaskin previousswitch_mm. So we only flushed the CPU1 tlb, and setted second version mapping of the pte. When the task switch from CPU1 to CPU0 again, CPU0 still used a stale tlb mapping entry which contained a wrong target physical address. When the task happened to read that value, the bug would be raised.Fixes 65d4b9c53017 ("RISC-V: Implement ASID allocator")Signed-off-by Guo Ren <[email protected]>Signed-off-by Guo Ren <[email protected]>Cc Anup Patel <[email protected]>Cc Palmer Dabbelt <[email protected]>---
arch/riscv/mm/context.c| 4 +++-1 file changed, 3 insertions(+), 1 deletion(-)arch/riscv/mm/context.c +0
-0
arch/riscv/mm/context.c void switch_mm(struct mm_struct *prev, struct mm_struct *next, · line 325
Quoted 10 lines
arch/riscv/mm/context.c +3
-1@@ -317,7 +317,9 @@ void switch_mm(struct mm_struct *prev, struct mm_struct *next,*/ cpu =smp_processor_id (); -cpumask_clear_cpu (cpu,mm_cpumask (prev)); +if (!static_branch_unlikely (&use_asid_allocator)) +cpumask_clear_cpu (cpu,mm_cpumask (prev)); +cpumask_set_cpu (cpu,mm_cpumask (next));set_mm (next, cpu);
This is a completely different patch to what you already sent. Why have you marked it RESEND rather than v2?
Quoted 62 lines · Conor Dooley
Quoted 59 lines · On 8 November 2022 10:20:44 GMT, [email protected] wrote:
From: Guo Ren <[email protected]>
After
use_asid_allocatorenabled, the userspace application will crash for stale tlb entry. Because only usingcpumask_clear_cpuwithoutlocal_flush_tlb_allcouldn't guarantee CPU's tlb entries fresh. Thenset_mm_asidwould cause user space application get a stale value by the stale tlb entry, butset_mm_noasidis okay.Here is the symptom of the bug:
unhandled signal 11 code0x1(coredump)0x0000003fd6d22524 <+4>: auipc s0,0x70 0x0000003fd6d22528 <+8>: ld s0,-148(s0) # 0x3fd6d92490=>
0x0000003fd6d2252c<+12>: ld a5,0(s0)
(gdb) i r s0
s00x8082ed1cc3198b210x8082ed1cc3198b21
(gdb) x/160x3fd6d924900x3fd6d92490:0xd80ac8a80x0000003f
The core dump file shows that the value of register s0 is wrong, but the value in memory is right. This is because 'ld s0, -148(s0)' use a stale mapping entry in TLB and got a wrong value from a stale physical address.When task run on CPU0, the task loaded/speculative-loaded the value of address(0x3fd6d92490), and the first version of tlb mapping entry was PTWed into CPU0's tlb.
When the task switched from CPU0 to CPU1 withoutlocal_tlb_flush_all(because of asid), the task happened to write a value on address (0x3fd6d92490). It causeddo_page_fault->wp_page_copy->ptep_clear_flush->ptep_get_and_clear&flush_tlb_page.
Theflush_tlb_pageusedmm_cpumask(mm)to determine which CPUs need tlb flush, but CPU0 had cleared the CPU0'smm_cpumaskin previousswitch_mm. So we only flushed the CPU1 tlb, and setted second version mapping of the pte. When the task switch from CPU1 to CPU0 again, CPU0 still used a stale tlb mapping entry which contained a wrong target physical address. When the task happened to read that value, the bug would be raised.Fixes 65d4b9c53017 ("RISC-V: Implement ASID allocator")Signed-off-by Guo Ren <[email protected]>Signed-off-by Guo Ren <[email protected]>Cc Anup Patel <[email protected]>Cc Palmer Dabbelt <[email protected]>---
arch/riscv/mm/context.c| 4 +++-1 file changed, 3 insertions(+), 1 deletion(-)arch/riscv/mm/context.c +3
-1@@ -317,7 +317,9 @@ void switch_mm(struct mm_struct *prev, struct mm_struct *next,*/ cpu =smp_processor_id (); -cpumask_clear_cpu (cpu,mm_cpumask (prev)); +if (!static_branch_unlikely (&use_asid_allocator)) +cpumask_clear_cpu (cpu,mm_cpumask (prev)); +cpumask_set_cpu (cpu,mm_cpumask (next));
Quoted 4 lines
arch/riscv/mm/context.c void switch_mm(struct mm_struct *prev, struct mm_struct *next, · line 325
Quoted 1 line
arch/riscv/mm/context.c +0
-0set_mm (next, cpu);This is a completely different patch to what you already sent. Why have you marked it RESEND rather than v2?
In addition, it seems to break the build for the nommu defconfigs.
_______________________________________________
linux-riscv mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-riscv
Yes, thx for pointing that out.
Quoted 70 lines · Conor Dooley
Quoted 62 lines · Conor Dooley
Quoted 59 lines · On 8 November 2022 10:20:44 GMT, [email protected] wrote:
From: Guo Ren <[email protected]>
After
use_asid_allocatorenabled, the userspace application will crash for stale tlb entry. Because only usingcpumask_clear_cpuwithoutlocal_flush_tlb_allcouldn't guarantee CPU's tlb entries fresh. Thenset_mm_asidwould cause user space application get a stale value by the stale tlb entry, butset_mm_noasidis okay.Here is the symptom of the bug:
unhandled signal 11 code0x1(coredump)0x0000003fd6d22524 <+4>: auipc s0,0x70 0x0000003fd6d22528 <+8>: ld s0,-148(s0) # 0x3fd6d92490=>
0x0000003fd6d2252c<+12>: ld a5,0(s0)
(gdb) i r s0
s00x8082ed1cc3198b210x8082ed1cc3198b21
(gdb) x/160x3fd6d924900x3fd6d92490:0xd80ac8a80x0000003f
The core dump file shows that the value of register s0 is wrong, but the value in memory is right. This is because 'ld s0, -148(s0)' use a stale mapping entry in TLB and got a wrong value from a stale physical address.When task run on CPU0, the task loaded/speculative-loaded the value of address(0x3fd6d92490), and the first version of tlb mapping entry was PTWed into CPU0's tlb.
When the task switched from CPU0 to CPU1 withoutlocal_tlb_flush_all(because of asid), the task happened to write a value on address (0x3fd6d92490). It causeddo_page_fault->wp_page_copy->ptep_clear_flush->ptep_get_and_clear&flush_tlb_page.
Theflush_tlb_pageusedmm_cpumask(mm)to determine which CPUs need tlb flush, but CPU0 had cleared the CPU0'smm_cpumaskin previousswitch_mm. So we only flushed the CPU1 tlb, and setted second version mapping of the pte. When the task switch from CPU1 to CPU0 again, CPU0 still used a stale tlb mapping entry which contained a wrong target physical address. When the task happened to read that value, the bug would be raised.Fixes 65d4b9c53017 ("RISC-V: Implement ASID allocator")Signed-off-by Guo Ren <[email protected]>Signed-off-by Guo Ren <[email protected]>Cc Anup Patel <[email protected]>Cc Palmer Dabbelt <[email protected]>---
arch/riscv/mm/context.c| 4 +++-1 file changed, 3 insertions(+), 1 deletion(-)arch/riscv/mm/context.c +3
-1@@ -317,7 +317,9 @@ void switch_mm(struct mm_struct *prev, struct mm_struct *next,*/ cpu =smp_processor_id (); -cpumask_clear_cpu (cpu,mm_cpumask (prev)); +if (!static_branch_unlikely (&use_asid_allocator)) +cpumask_clear_cpu (cpu,mm_cpumask (prev)); +cpumask_set_cpu (cpu,mm_cpumask (next));Quoted 4 lines
arch/riscv/mm/context.c void switch_mm(struct mm_struct *prev, struct mm_struct *next, · line 325
Quoted 1 line
arch/riscv/mm/context.c +0
-0set_mm (next, cpu);This is a completely different patch to what you already sent. Why have you marked it RESEND rather than v2?
In addition, it seems to break the build for the nommu defconfigs.
Signature · 2 lines
Best Regards Guo Ren
Quoted 63 lines · Conor Dooley
Quoted 59 lines · On 8 November 2022 10:20:44 GMT, [email protected] wrote:
From: Guo Ren <[email protected]>
After
use_asid_allocatorenabled, the userspace application will crash for stale tlb entry. Because only usingcpumask_clear_cpuwithoutlocal_flush_tlb_allcouldn't guarantee CPU's tlb entries fresh. Thenset_mm_asidwould cause user space application get a stale value by the stale tlb entry, butset_mm_noasidis okay.Here is the symptom of the bug:
unhandled signal 11 code0x1(coredump)0x0000003fd6d22524 <+4>: auipc s0,0x70 0x0000003fd6d22528 <+8>: ld s0,-148(s0) # 0x3fd6d92490=>
0x0000003fd6d2252c<+12>: ld a5,0(s0)
(gdb) i r s0
s00x8082ed1cc3198b210x8082ed1cc3198b21
(gdb) x/160x3fd6d924900x3fd6d92490:0xd80ac8a80x0000003f
The core dump file shows that the value of register s0 is wrong, but the value in memory is right. This is because 'ld s0, -148(s0)' use a stale mapping entry in TLB and got a wrong value from a stale physical address.When task run on CPU0, the task loaded/speculative-loaded the value of address(0x3fd6d92490), and the first version of tlb mapping entry was PTWed into CPU0's tlb.
When the task switched from CPU0 to CPU1 withoutlocal_tlb_flush_all(because of asid), the task happened to write a value on address (0x3fd6d92490). It causeddo_page_fault->wp_page_copy->ptep_clear_flush->ptep_get_and_clear&flush_tlb_page.
Theflush_tlb_pageusedmm_cpumask(mm)to determine which CPUs need tlb flush, but CPU0 had cleared the CPU0'smm_cpumaskin previousswitch_mm. So we only flushed the CPU1 tlb, and setted second version mapping of the pte. When the task switch from CPU1 to CPU0 again, CPU0 still used a stale tlb mapping entry which contained a wrong target physical address. When the task happened to read that value, the bug would be raised.Fixes 65d4b9c53017 ("RISC-V: Implement ASID allocator")Signed-off-by Guo Ren <[email protected]>Signed-off-by Guo Ren <[email protected]>Cc Anup Patel <[email protected]>Cc Palmer Dabbelt <[email protected]>---
arch/riscv/mm/context.c| 4 +++-1 file changed, 3 insertions(+), 1 deletion(-)arch/riscv/mm/context.c +3
-1@@ -317,7 +317,9 @@ void switch_mm(struct mm_struct *prev, struct mm_struct *next,*/ cpu =smp_processor_id (); -cpumask_clear_cpu (cpu,mm_cpumask (prev)); +if (!static_branch_unlikely (&use_asid_allocator)) +cpumask_clear_cpu (cpu,mm_cpumask (prev)); +cpumask_set_cpu (cpu,mm_cpumask (next));
Quoted 3 lines
arch/riscv/mm/context.c void switch_mm(struct mm_struct *prev, struct mm_struct *next, · line 325
Quoted 1 line
arch/riscv/mm/context.c +0
-0set_mm (next, cpu);This is a completely different patch to what you already sent. Why have you marked it RESEND rather than v2?
Okay, I should send v2.
Signature · 2 lines
Best Regards Guo Ren
kernel test robot
build botI love your patch! Yet something to improve:
Hi,
I love your patch! Yet something to improve:
[auto build test ERROR on linus/master]
[also build test ERROR on v6.1-rc4 next-20221108]
[If your patch is applied to the wrong git tree, kindly drop us a note. And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch#_base_tree_information]
url: https://github.com/intel-lab-lkp/linux/commits/guoren-kernel-org/riscv-asid-Fixup-stale-TLB-entry-cause-application-crash/20221108-182151 patch link: https://lore.kernel.org/r/20221108102044.3317793-1-guoren%40kernel.org patch subject: [PATCH RESEND] riscv: asid: Fixup stale TLB entry cause application crash config: riscv-nommu_virt_defconfig compiler: riscv64-linux-gcc (GCC) 12.1.0
reproduce (this is a W=1 build):
wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross chmod +x ~/bin/make.cross
# https://github.com/intel-lab-lkp/linux/commit/025af39c1eb149e584705dfc72ac117812c82f3e
git remote add linux-review https://github.com/intel-lab-lkp/linux
git fetch --no-tags linux-review guoren-kernel-org/riscv-asid-Fixup-stale-TLB-entry-cause-application-crash/20221108-182151 git checkout 025af39c1eb149e584705dfc72ac117812c82f3e
# save the config file
mkdir build_dir && cp config build_dir/.config
COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-12.1.0 make.cross W=1 O=build_dir ARCH=riscv SHELL=/bin/bash
If you fix the issue, kindly add following tag where applicable | Reported-by: kernel test robot <[email protected]>
All errors (new ones prefixed by >>):
riscv64-linux-ld: arch/riscv/mm/context.o: in function `.L0 ':
>> context.c:(__jump_table+0x8): undefined reference to `use_asid_allocator'
Signature · 2 lines
0-DAY CI Kernel Test Service https://01.org/lkp
#
# Automatically generated file; DO NOT EDIT.
# Linux/riscv 6.1.0-rc4 Kernel Configuration
#CONFIG_CC_VERSION_TEXT="riscv64-linux-gcc (GCC) 12.1.0" CONFIG_CC_IS_GCC=yCONFIG_GCC_VERSION=120100 CONFIG_CLANG_VERSION=0CONFIG_AS_IS_GNU=yCONFIG_AS_VERSION=23800CONFIG_LD_IS_BFD=yCONFIG_LD_VERSION=23800CONFIG_LLD_VERSION=0 CONFIG_CC_HAS_ASM_GOTO_OUTPUT=y CONFIG_CC_HAS_ASM_INLINE=y CONFIG_CC_HAS_NO_PROFILE_FN_ATTR=y CONFIG_PAHOLE_VERSION=123CONFIG_IRQ_WORK=yCONFIG_THREAD_INFO_IN_TASK=y
#
# General setup
#CONFIG_INIT_ENV_ARG_LIMIT=32
# CONFIG_COMPILE_TEST is not set
# CONFIG_WERROR is not setCONFIG_LOCALVERSION=""CONFIG_LOCALVERSION_AUTO=yCONFIG_BUILD_SALT=""CONFIG_DEFAULT_INIT=""CONFIG_DEFAULT_HOSTNAME="(none)"
# CONFIG_SYSVIPC is not set
# CONFIG_WATCH_QUEUE is not set
# CONFIG_USELIB is not setCONFIG_HAVE_ARCH_AUDITSYSCALL=y
#
# IRQ subsystem
#CONFIG_GENERIC_IRQ_SHOW=yCONFIG_GENERIC_IRQ_SHOW_LEVEL=yCONFIG_GENERIC_IRQ_EFFECTIVE_AFF_MASK=yCONFIG_HARDIRQS_SW_RESEND=yCONFIG_IRQ_DOMAIN=yCONFIG_IRQ_DOMAIN_HIERARCHY=yCONFIG_IRQ_FORCED_THREADING=yCONFIG_SPARSE_IRQ=y
# end of IRQ subsystem
CONFIG_GENERIC_IRQ_MULTI_HANDLER=yCONFIG_ARCH_CLOCKSOURCE_INIT=yCONFIG_GENERIC_CLOCKEVENTS=yCONFIG_ARCH_HAS_TICK_BROADCAST=yCONFIG_GENERIC_CLOCKEVENTS_BROADCAST=yCONFIG_HAVE_POSIX_CPU_TIMERS_TASK_WORK=yCONFIG_POSIX_CPU_TIMERS_TASK_WORK=yCONFIG_CONTEXT_TRACKING=yCONFIG_CONTEXT_TRACKING_IDLE=y
#
# Timers subsystem
#CONFIG_HZ_PERIODIC=y
# CONFIG_NO_HZ_IDLE is not set
# CONFIG_NO_HZ_FULL is not set
# CONFIG_NO_HZ is not set
# CONFIG_HIGH_RES_TIMERS is not set
# end of Timers subsystem
#
# BPF subsystem
#
# CONFIG_BPF_SYSCALL is not set
# end of BPF subsystem
CONFIG_PREEMPT_NONE_BUILD=yCONFIG_PREEMPT_NONE=y
# CONFIG_PREEMPT_VOLUNTARY is not set
# CONFIG_PREEMPT is not set
#
# CPU/Task time and stats accounting
#CONFIG_TICK_CPU_ACCOUNTING=y
# CONFIG_VIRT_CPU_ACCOUNTING_GEN is not set
# CONFIG_IRQ_TIME_ACCOUNTING is not set
# CONFIG_BSD_PROCESS_ACCT is not set
# CONFIG_PSI is not set
# end of CPU/Task time and stats accounting
# CONFIG_CPU_ISOLATION is not set
#
# RCU Subsystem
#CONFIG_TREE_RCU=y
# CONFIG_RCU_EXPERT is not setCONFIG_SRCU=yCONFIG_TREE_SRCU=yCONFIG_RCU_STALL_COMMON=yCONFIG_RCU_NEED_SEGCBLIST=y
# end of RCU Subsystem
# CONFIG_IKCONFIG is not set
# CONFIG_IKHEADERS is not setCONFIG_LOG_BUF_SHIFT=16CONFIG_LOG_CPU_MAX_BUF_SHIFT=12CONFIG_PRINTK_SAFE_LOG_BUF_SHIFT=12CONFIG_GENERIC_SCHED_CLOCK=y
#
# Scheduler features
#
# end of Scheduler features
CONFIG_CC_HAS_INT128=y CONFIG_CC_IMPLICIT_FALLTHROUGH="-Wimplicit-fallthrough=5" CONFIG_GCC12_NO_ARRAY_BOUNDS=y CONFIG_CC_NO_ARRAY_BOUNDS=y CONFIG_ARCH_SUPPORTS_INT128=y
# CONFIG_CGROUPS is not set
# CONFIG_NAMESPACES is not set
# CONFIG_CHECKPOINT_RESTORE is not set
# CONFIG_SCHED_AUTOGROUP is not set
# CONFIG_SYSFS_DEPRECATED is not set
# CONFIG_RELAY is not set CONFIG_BLK_DEV_INITRD=y CONFIG_INITRAMFS_SOURCE=""
# CONFIG_INITRAMFS_FORCE is not set CONFIG_RD_GZIP=y
# CONFIG_RD_BZIP2 is not set
# CONFIG_RD_LZMA is not set
# CONFIG_RD_XZ is not set
# CONFIG_RD_LZO is not set
# CONFIG_RD_LZ4 is not setCONFIG_RD_ZSTD=y
# CONFIG_BOOT_CONFIG is not set CONFIG_INITRAMFS_PRESERVE_MTIME=y
# CONFIG_CC_OPTIMIZE_FOR_PERFORMANCE is not set CONFIG_CC_OPTIMIZE_FOR_SIZE=yCONFIG_SYSCTL=yCONFIG_SYSCTL_EXCEPTION_TRACE=yCONFIG_EXPERT=yCONFIG_MULTIUSER=y
# CONFIG_SGETMASK_SYSCALL is not set
# CONFIG_SYSFS_SYSCALL is not set
# CONFIG_FHANDLE is not set CONFIG_POSIX_TIMERS=yCONFIG_PRINTK=yCONFIG_BUG=y
# CONFIG_BASE_FULL is not setCONFIG_FUTEX=yCONFIG_FUTEX_PI=y
# CONFIG_EPOLL is not set
# CONFIG_SIGNALFD is not set
# CONFIG_TIMERFD is not set
# CONFIG_EVENTFD is not set
# CONFIG_AIO is not set
# CONFIG_IO_URING is not set
# CONFIG_ADVISE_SYSCALLS is not set CONFIG_MEMBARRIER=y
# CONFIG_KALLSYMS is not set
# CONFIG_KCMP is not setCONFIG_RSEQ=y
# CONFIG_DEBUG_RSEQ is not set
# CONFIG_EMBEDDED is not set CONFIG_HAVE_PERF_EVENTS=y
# CONFIG_PC104 is not set
#
# Kernel Performance Events And Counters
#
# CONFIG_PERF_EVENTS is not set
# end of Kernel Performance Events And Counters
# CONFIG_PROFILING is not set
# end of General setup
CONFIG_64BIT=yCONFIG_RISCV=yCONFIG_ARCH_MMAP_RND_BITS_MIN=18CONFIG_ARCH_MMAP_RND_COMPAT_BITS_MIN=8CONFIG_ARCH_MMAP_RND_BITS_MAX=24CONFIG_ARCH_MMAP_RND_COMPAT_BITS_MAX=17CONFIG_RISCV_M_MODE=y
# CONFIG_MMU is not setCONFIG_PAGE_OFFSET=0x80000000CONFIG_ARCH_FLATMEM_ENABLE=yCONFIG_ARCH_SUPPORTS_UPROBES=yCONFIG_STACKTRACE_SUPPORT=yCONFIG_GENERIC_BUG=yCONFIG_GENERIC_BUG_RELATIVE_POINTERS=yCONFIG_GENERIC_CALIBRATE_DELAY=yCONFIG_GENERIC_CSUM=yCONFIG_GENERIC_HWEIGHT=yCONFIG_PGTABLE_LEVELS=5CONFIG_LOCKDEP_SUPPORT=yCONFIG_AS_HAS_INSN=y
#
# SoC selection
#
# CONFIG_SOC_MICROCHIP_POLARFIRE is not set
# CONFIG_SOC_SIFIVE is not set
# CONFIG_SOC_STARFIVE is not setCONFIG_SOC_VIRT=y
# CONFIG_SOC_CANAAN is not set
# end of SoC selection
#
# CPU errata selection
#
# CONFIG_ERRATA_SIFIVE is not set
# CONFIG_ERRATA_THEAD is not set
# end of CPU errata selection
#
# Platform type
#CONFIG_NONPORTABLE=y
# CONFIG_ARCH_RV32I is not setCONFIG_ARCH_RV64I=y
# CONFIG_CMODEL_MEDLOW is not setCONFIG_CMODEL_MEDANY=yCONFIG_SMP=yCONFIG_NR_CPUS=64
# CONFIG_HOTPLUG_CPU is not setCONFIG_TUNE_GENERIC=yCONFIG_RISCV_ISA_C=yCONFIG_TOOLCHAIN_HAS_ZIHINTPAUSE=yCONFIG_FPU=y
# end of Platform type
#
# Kernel features
#
# CONFIG_HZ_100 is not setCONFIG_HZ_250=y
# CONFIG_HZ_300 is not set
# CONFIG_HZ_1000 is not setCONFIG_HZ=250CONFIG_RISCV_BOOT_SPINWAIT=y
# CONFIG_KEXEC_FILE is not set
# CONFIG_CRASH_DUMP is not set
# end of Kernel features
#
# Boot options
#CONFIG_CMDLINE="root=/dev/vda rw earlycon=uart8250,mmio,0x10000000,115200n8 console=ttyS0" # CONFIG_CMDLINE_FALLBACK is not set
# CONFIG_CMDLINE_EXTEND is not setCONFIG_CMDLINE_FORCE=yCONFIG_CC_HAVE_STACKPROTECTOR_TLS=yCONFIG_STACKPROTECTOR_PER_TASK=y
# CONFIG_PHYS_RAM_BASE_FIXED is not set
# end of Boot options
#
# Power management options
#
# CONFIG_PM is not set
# end of Power management options
#
# CPU Power Management
#
#
# CPU Idle
#
# CONFIG_CPU_IDLE is not set
# end of CPU Idle # end of CPU Power Management
# CONFIG_VIRTUALIZATION is not set
#
# General architecture-dependent options
#CONFIG_JUMP_LABEL=y
# CONFIG_STATIC_KEYS_SELFTEST is not setCONFIG_HAVE_64BIT_ALIGNED_ACCESS=yCONFIG_HAVE_KPROBES=yCONFIG_HAVE_KRETPROBES=yCONFIG_HAVE_KPROBES_ON_FTRACE=yCONFIG_HAVE_FUNCTION_ERROR_INJECTION=yCONFIG_TRACE_IRQFLAGS_SUPPORT=yCONFIG_HAVE_ARCH_TRACEHOOK=yCONFIG_GENERIC_SMP_IDLE_THREAD=yCONFIG_GENERIC_IDLE_POLL_SETUP=yCONFIG_ARCH_HAS_FORTIFY_SOURCE=yCONFIG_HAVE_ARCH_THREAD_STRUCT_WHITELIST=yCONFIG_HAVE_ASM_MODVERSIONS=yCONFIG_HAVE_REGS_AND_STACK_ACCESS_API=yCONFIG_HAVE_RSEQ=yCONFIG_HAVE_FUNCTION_ARG_ACCESS_API=yCONFIG_HAVE_PERF_REGS=yCONFIG_HAVE_PERF_USER_STACK_DUMP=yCONFIG_HAVE_ARCH_JUMP_LABEL=yCONFIG_HAVE_ARCH_JUMP_LABEL_RELATIVE=yCONFIG_HAVE_ARCH_SECCOMP=yCONFIG_HAVE_ARCH_SECCOMP_FILTER=yCONFIG_SECCOMP=yCONFIG_HAVE_STACKPROTECTOR=yCONFIG_STACKPROTECTOR=yCONFIG_STACKPROTECTOR_STRONG=yCONFIG_LTO_NONE=yCONFIG_HAVE_CONTEXT_TRACKING_USER=yCONFIG_HAVE_VIRT_CPU_ACCOUNTING_GEN=yCONFIG_HAVE_IRQ_TIME_ACCOUNTING=yCONFIG_HAVE_MOVE_PUD=yCONFIG_HAVE_MOVE_PMD=yCONFIG_ARCH_WANT_HUGE_PMD_SHARE=yCONFIG_PAGE_SIZE_LESS_THAN_64KB=yCONFIG_PAGE_SIZE_LESS_THAN_256KB=yCONFIG_CLONE_BACKWARDS=y
# CONFIG_COMPAT_32BIT_TIME is not setCONFIG_ARCH_OPTIONAL_KERNEL_RWX_DEFAULT=y
#
# GCOV-based kernel profiling
#CONFIG_ARCH_HAS_GCOV_PROFILE_ALL=y
# end of GCOV-based kernel profiling
CONFIG_HAVE_GCC_PLUGINS=yCONFIG_GCC_PLUGINS=y
# CONFIG_GCC_PLUGIN_LATENT_ENTROPY is not set
# end of General architecture-dependent options
CONFIG_RT_MUTEXES=yCONFIG_BASE_SMALL=1
# CONFIG_MODULES is not setCONFIG_BLOCK=yCONFIG_BLOCK_LEGACY_AUTOLOAD=y
# CONFIG_BLK_DEV_BSGLIB is not set
# CONFIG_BLK_DEV_INTEGRITY is not set
# CONFIG_BLK_DEV_ZONED is not set
# CONFIG_BLK_WBT is not set
# CONFIG_BLK_SED_OPAL is not set
# CONFIG_BLK_INLINE_ENCRYPTION is not set
#
# Partition Types
#CONFIG_PARTITION_ADVANCED=y
# CONFIG_ACORN_PARTITION is not set
# CONFIG_AIX_PARTITION is not set
# CONFIG_OSF_PARTITION is not set
# CONFIG_AMIGA_PARTITION is not set
# CONFIG_ATARI_PARTITION is not set
# CONFIG_MAC_PARTITION is not set
# CONFIG_MSDOS_PARTITION is not set
# CONFIG_LDM_PARTITION is not set
# CONFIG_SGI_PARTITION is not set
# CONFIG_ULTRIX_PARTITION is not set
# CONFIG_SUN_PARTITION is not set
# CONFIG_KARMA_PARTITION is not set
# CONFIG_EFI_PARTITION is not set
# CONFIG_SYSV68_PARTITION is not set
# CONFIG_CMDLINE_PARTITION is not set
# end of Partition Types
CONFIG_BLK_MQ_VIRTIO=y
#
# IO Schedulers
#
# CONFIG_MQ_IOSCHED_DEADLINE is not set
# CONFIG_MQ_IOSCHED_KYBER is not set
# CONFIG_IOSCHED_BFQ is not set
# end of IO Schedulers
CONFIG_INLINE_SPIN_UNLOCK_IRQ=yCONFIG_INLINE_READ_UNLOCK=yCONFIG_INLINE_READ_UNLOCK_IRQ=yCONFIG_INLINE_WRITE_UNLOCK=yCONFIG_INLINE_WRITE_UNLOCK_IRQ=yCONFIG_ARCH_SUPPORTS_ATOMIC_RMW=yCONFIG_MUTEX_SPIN_ON_OWNER=yCONFIG_RWSEM_SPIN_ON_OWNER=yCONFIG_LOCK_SPIN_ON_OWNER=yCONFIG_ARCH_USE_QUEUED_RWLOCKS=yCONFIG_QUEUED_RWLOCKS=yCONFIG_ARCH_HAS_MMIOWB=yCONFIG_MMIOWB=y
#
# Executable file formats
#CONFIG_BINFMT_SCRIPT=yCONFIG_ARCH_HAS_BINFMT_FLAT=yCONFIG_BINFMT_FLAT=yCONFIG_BINFMT_FLAT_NO_DATA_START_OFFSET=y
# CONFIG_BINFMT_FLAT_OLD is not set
# CONFIG_BINFMT_ZFLAT is not set
# CONFIG_BINFMT_MISC is not set
# CONFIG_COREDUMP is not set
# end of Executable file formats
#
# Memory Management options
#
#
# SLAB allocator options
#
# CONFIG_SLAB is not set
# CONFIG_SLUB is not setCONFIG_SLOB=y
# end of SLAB allocator options
# CONFIG_SHUFFLE_PAGE_ALLOCATOR is not set
# CONFIG_COMPAT_BRK is not set
# CONFIG_MMAP_ALLOW_UNINITIALIZED is not setCONFIG_FLATMEM=yCONFIG_EXCLUSIVE_SYSTEM_RAM=yCONFIG_SPLIT_PTLOCK_CPUS=999999CONFIG_ARCH_ENABLE_SPLIT_PMD_PTLOCK=y
# CONFIG_PAGE_REPORTING is not setCONFIG_PHYS_ADDR_T_64BIT=yCONFIG_NOMMU_INITIAL_TRIM_EXCESS=1CONFIG_ARCH_WANT_GENERAL_HUGETLB=yCONFIG_NEED_PER_CPU_KM=yCONFIG_GENERIC_EARLY_IOREMAP=yCONFIG_ARCH_HAS_CURRENT_STACK_POINTER=yCONFIG_ZONE_DMA32=y
# CONFIG_VM_EVENT_COUNTERS is not set
# CONFIG_PERCPU_STATS is not set
#
# GUP_TEST needs to have DEBUG_FS enabled
#CONFIG_ARCH_HAS_PTE_SPECIAL=y
#
# Data Access Monitoring
#
# CONFIG_DAMON is not set
# end of Data Access Monitoring # end of Memory Management options
# CONFIG_NET is not set
#
# Device Drivers
#CONFIG_HAVE_PCI=y
# CONFIG_PCI is not set
# CONFIG_PCCARD is not set
#
# Generic Driver Options
#
# CONFIG_UEVENT_HELPER is not setCONFIG_DEVTMPFS=yCONFIG_DEVTMPFS_MOUNT=y
# CONFIG_DEVTMPFS_SAFE is not setCONFIG_STANDALONE=yCONFIG_PREVENT_FIRMWARE_BUILD=y
#
# Firmware loader
#
# CONFIG_FW_LOADER is not set
# end of Firmware loader
# CONFIG_ALLOW_DEV_COREDUMP is not set
# CONFIG_DEBUG_DRIVER is not set
# CONFIG_DEBUG_DEVRES is not set
# CONFIG_DEBUG_TEST_DRIVER_REMOVE is not setCONFIG_REGMAP=yCONFIG_REGMAP_MMIO=yCONFIG_GENERIC_ARCH_TOPOLOGY=y
# end of Generic Driver Options
#
# Bus devices
#
# CONFIG_MHI_BUS is not set
# CONFIG_MHI_BUS_EP is not set
# end of Bus devices
#
# Firmware Drivers
#
#
# ARM System Control and Management Interface Protocol #
# end of ARM System Control and Management Interface Protocol
# CONFIG_FIRMWARE_MEMMAP is not set
# CONFIG_GOOGLE_FIRMWARE is not set
#
# Tegra firmware driver
#
# end of Tegra firmware driver # end of Firmware Drivers
# CONFIG_GNSS is not set
# CONFIG_MTD is not setCONFIG_DTC=yCONFIG_OF=y
# CONFIG_OF_UNITTEST is not setCONFIG_OF_FLATTREE=yCONFIG_OF_EARLY_FLATTREE=yCONFIG_OF_KOBJ=yCONFIG_OF_ADDRESS=yCONFIG_OF_IRQ=yCONFIG_OF_RESERVED_MEM=y
# CONFIG_OF_OVERLAY is not setCONFIG_OF_DMA_DEFAULT_COHERENT=y
# CONFIG_PARPORT is not setCONFIG_BLK_DEV=y
# CONFIG_BLK_DEV_NULL_BLK is not set
# CONFIG_BLK_DEV_LOOP is not set
#
# DRBD disabled because PROC_FS or INET not selected #
# CONFIG_BLK_DEV_RAM is not set CONFIG_VIRTIO_BLK=y
# CONFIG_BLK_DEV_UBLK is not set
#
# NVME Support
#
# CONFIG_NVME_FC is not set
# end of NVME Support
#
# Misc devices
#
# CONFIG_DUMMY_IRQ is not set
# CONFIG_ENCLOSURE_SERVICES is not set
# CONFIG_SRAM is not set
# CONFIG_XILINX_SDFEC is not set
# CONFIG_OPEN_DICE is not set
# CONFIG_VCPU_STALL_DETECTOR is not set
# CONFIG_C2PORT is not set
#
# EEPROM support
#
# CONFIG_EEPROM_93CX6 is not set
# end of EEPROM support
#
# Texas Instruments shared transport line discipline #
# end of Texas Instruments shared transport line discipline
#
# Altera FPGA firmware download module (requires I2C) #
# CONFIG_ECHO is not set
# CONFIG_PVPANIC is not set
# end of Misc devices
#
# SCSI device support
#CONFIG_SCSI_MOD=y
# CONFIG_RAID_ATTRS is not set
# CONFIG_SCSI is not set
# end of SCSI device support
# CONFIG_ATA is not set
# CONFIG_MD is not set
# CONFIG_TARGET_CORE is not set
#
# Input device support
#CONFIG_INPUT=y
# CONFIG_INPUT_FF_MEMLESS is not set
# CONFIG_INPUT_SPARSEKMAP is not set
# CONFIG_INPUT_MATRIXKMAP is not set
#
# Userland interfaces
#
# CONFIG_INPUT_MOUSEDEV is not set
# CONFIG_INPUT_JOYDEV is not set
# CONFIG_INPUT_EVDEV is not set
# CONFIG_INPUT_EVBUG is not set
#
# Input Device Drivers
#
# CONFIG_INPUT_KEYBOARD is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TABLET is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
# CONFIG_INPUT_MISC is not set
# CONFIG_RMI4_CORE is not set
#
# Hardware I/O ports
#
# CONFIG_SERIO is not set
# CONFIG_GAMEPORT is not set
# end of Hardware I/O ports # end of Input device support
#
# Character devices
#CONFIG_TTY=yCONFIG_VT=yCONFIG_CONSOLE_TRANSLATIONS=yCONFIG_VT_CONSOLE=yCONFIG_HW_CONSOLE=y
# CONFIG_VT_HW_CONSOLE_BINDING is not setCONFIG_UNIX98_PTYS=y
# CONFIG_LEGACY_PTYS is not set
# CONFIG_LDISC_AUTOLOAD is not set
#
# Serial drivers
#CONFIG_SERIAL_EARLYCON=y CONFIG_SERIAL_8250=y
# CONFIG_SERIAL_8250_DEPRECATED_OPTIONS is not set CONFIG_SERIAL_8250_16550A_VARIANTS=y
# CONFIG_SERIAL_8250_FINTEK is not set CONFIG_SERIAL_8250_CONSOLE=y CONFIG_SERIAL_8250_NR_UARTS=1 CONFIG_SERIAL_8250_RUNTIME_UARTS=1
# CONFIG_SERIAL_8250_EXTENDED is not set
# CONFIG_SERIAL_8250_DW is not set
# CONFIG_SERIAL_8250_RT288X is not set CONFIG_SERIAL_OF_PLATFORM=y
#
# Non-8250 serial port support
#
# CONFIG_SERIAL_UARTLITE is not setCONFIG_SERIAL_CORE=yCONFIG_SERIAL_CORE_CONSOLE=y
# CONFIG_SERIAL_SIFIVE is not set
# CONFIG_SERIAL_SCCNXP is not set
# CONFIG_SERIAL_ALTERA_JTAGUART is not set
# CONFIG_SERIAL_ALTERA_UART is not set
# CONFIG_SERIAL_XILINX_PS_UART is not set
# CONFIG_SERIAL_ARC is not set
# CONFIG_SERIAL_FSL_LPUART is not set
# CONFIG_SERIAL_FSL_LINFLEXUART is not set
# CONFIG_SERIAL_CONEXANT_DIGICOLOR is not set
# CONFIG_SERIAL_SPRD is not set
# end of Serial drivers
# CONFIG_SERIAL_NONSTANDARD is not set
# CONFIG_GOLDFISH_TTY is not set
# CONFIG_NULL_TTY is not set
# CONFIG_SERIAL_DEV_BUS is not set
# CONFIG_TTY_PRINTK is not set
# CONFIG_VIRTIO_CONSOLE is not set
# CONFIG_IPMI_HANDLER is not set
# CONFIG_HW_RANDOM is not set
# CONFIG_DEVMEM is not set
# CONFIG_TCG_TPM is not set
# CONFIG_XILLYBUS is not setCONFIG_RANDOM_TRUST_CPU=yCONFIG_RANDOM_TRUST_BOOTLOADER=y
# end of Character devices
#
# I2C support
#
# CONFIG_I2C is not set
# end of I2C support
# CONFIG_I3C is not set
# CONFIG_SPI is not set
# CONFIG_SPMI is not set
# CONFIG_HSI is not set
# CONFIG_PPS is not set
#
# PTP clock support
#CONFIG_PTP_1588_CLOCK_OPTIONAL=y
#
# Enable PHYLIB and NETWORK_PHY_TIMESTAMPING to see the additional clocks. #
# end of PTP clock support
# CONFIG_PINCTRL is not set
# CONFIG_GPIOLIB is not set
# CONFIG_W1 is not setCONFIG_POWER_RESET=y
# CONFIG_POWER_RESET_RESTART is not setCONFIG_POWER_RESET_SYSCON=yCONFIG_POWER_RESET_SYSCON_POWEROFF=y
# CONFIG_SYSCON_REBOOT_MODE is not set
# CONFIG_NVMEM_REBOOT_MODE is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
# CONFIG_WATCHDOG is not setCONFIG_SSB_POSSIBLE=y
# CONFIG_SSB is not setCONFIG_BCMA_POSSIBLE=y
# CONFIG_BCMA is not set
#
# Multifunction device drivers
#
# CONFIG_MFD_ATMEL_FLEXCOM is not set
# CONFIG_MFD_ATMEL_HLCDC is not set
# CONFIG_MFD_MADERA is not set
# CONFIG_MFD_HI6421_PMIC is not set
# CONFIG_HTC_PASIC3 is not set
# CONFIG_MFD_KEMPLD is not set
# CONFIG_MFD_MT6397 is not set
# CONFIG_MFD_SM501 is not setCONFIG_MFD_SYSCON=y
# CONFIG_MFD_TI_AM335X_TSCADC is not set
# CONFIG_MFD_TQMX86 is not set
# end of Multifunction device drivers
# CONFIG_REGULATOR is not set
# CONFIG_RC_CORE is not set
#
# CEC support
#
# CONFIG_MEDIA_CEC_SUPPORT is not set
# end of CEC support
# CONFIG_MEDIA_SUPPORT is not set
#
# Graphics support
#
# CONFIG_DRM is not set
# CONFIG_DRM_DEBUG_MODESET_LOCK is not set
#
# ARM devices
#
# end of ARM devices
#
# Frame buffer Devices
#
# CONFIG_FB is not set
# end of Frame buffer Devices
#
# Backlight & LCD device support
#
# CONFIG_LCD_CLASS_DEVICE is not set
# CONFIG_BACKLIGHT_CLASS_DEVICE is not set
# end of Backlight & LCD device support
#
# Console display driver support
#
# CONFIG_VGA_CONSOLE is not setCONFIG_DUMMY_CONSOLE=yCONFIG_DUMMY_CONSOLE_COLUMNS=80CONFIG_DUMMY_CONSOLE_ROWS=25
# end of Console display driver support # end of Graphics support
# CONFIG_SOUND is not set
#
# HID support
#
# CONFIG_HID is not set
# end of HID support
CONFIG_USB_OHCI_LITTLE_ENDIAN=y
# CONFIG_USB_SUPPORT is not set
# CONFIG_MMC is not set
# CONFIG_MEMSTICK is not set
# CONFIG_NEW_LEDS is not set
# CONFIG_ACCESSIBILITY is not setCONFIG_EDAC_SUPPORT=y
# CONFIG_RTC_CLASS is not set
# CONFIG_DMADEVICES is not set
#
# DMABUF options
#
# CONFIG_SYNC_FILE is not set
# CONFIG_DMABUF_HEAPS is not set
# end of DMABUF options
# CONFIG_AUXDISPLAY is not set
# CONFIG_VFIO is not set
# CONFIG_VIRT_DRIVERS is not setCONFIG_VIRTIO_ANCHOR=yCONFIG_VIRTIO=yCONFIG_VIRTIO_MENU=y
# CONFIG_VIRTIO_BALLOON is not set
# CONFIG_VIRTIO_INPUT is not setCONFIG_VIRTIO_MMIO=yCONFIG_VIRTIO_MMIO_CMDLINE_DEVICES=yCONFIG_VHOST_MENU=y
# CONFIG_VHOST_CROSS_ENDIAN_LEGACY is not set
#
# Microsoft Hyper-V guest support
#
# end of Microsoft Hyper-V guest support
# CONFIG_GREYBUS is not set
# CONFIG_COMEDI is not set
# CONFIG_STAGING is not setCONFIG_GOLDFISH=y
# CONFIG_GOLDFISH_PIPE is not setCONFIG_HAVE_CLK=yCONFIG_HAVE_CLK_PREPARE=yCONFIG_COMMON_CLK=y
# CONFIG_COMMON_CLK_AXI_CLKGEN is not set
# CONFIG_COMMON_CLK_FIXED_MMIO is not set
# CONFIG_XILINX_VCU is not set
# CONFIG_COMMON_CLK_XLNX_CLKWZRD is not set
# CONFIG_HWSPINLOCK is not set
#
# Clock Source drivers
#CONFIG_TIMER_OF=yCONFIG_TIMER_PROBE=yCONFIG_CLINT_TIMER=y
# CONFIG_MICROCHIP_PIT64B is not set
# end of Clock Source drivers
# CONFIG_MAILBOX is not set
#
# Remoteproc drivers
#
# CONFIG_REMOTEPROC is not set
# end of Remoteproc drivers
#
# Rpmsg drivers
#
# CONFIG_RPMSG_VIRTIO is not set
# end of Rpmsg drivers
# CONFIG_SOUNDWIRE is not set
#
# SOC (System On Chip) specific Drivers
#
#
# Amlogic SoC drivers
#
# end of Amlogic SoC drivers
#
# Broadcom SoC drivers
#
# end of Broadcom SoC drivers
#
# NXP/Freescale QorIQ SoC drivers
#
# end of NXP/Freescale QorIQ SoC drivers
#
# fujitsu SoC drivers # # end of fujitsu SoC drivers
#
# i.MX SoC drivers
#
# end of i.MX SoC drivers
#
# Enable LiteX SoC Builder specific drivers
#
# CONFIG_LITEX_SOC_CONTROLLER is not set
# end of Enable LiteX SoC Builder specific drivers
#
# Qualcomm SoC drivers
#
# end of Qualcomm SoC drivers
# CONFIG_SOC_TI is not set
#
# Xilinx SoC drivers
#
# end of Xilinx SoC drivers # end of SOC (System On Chip) specific Drivers
# CONFIG_PM_DEVFREQ is not set
# CONFIG_EXTCON is not set
# CONFIG_MEMORY is not set
# CONFIG_IIO is not set
# CONFIG_PWM is not set
#
# IRQ chip support
#CONFIG_IRQCHIP=y
# CONFIG_AL_FIC is not set
# CONFIG_XILINX_INTC is not setCONFIG_RISCV_INTC=yCONFIG_SIFIVE_PLIC=y
# end of IRQ chip support
# CONFIG_IPACK_BUS is not set
# CONFIG_RESET_CONTROLLER is not set
#
# PHY Subsystem
#
# CONFIG_GENERIC_PHY is not set
# CONFIG_PHY_CAN_TRANSCEIVER is not set
#
# PHY drivers for Broadcom platforms
#
# CONFIG_BCM_KONA_USB2_PHY is not set
# end of PHY drivers for Broadcom platforms
# CONFIG_PHY_CADENCE_TORRENT is not set
# CONFIG_PHY_CADENCE_DPHY is not set
# CONFIG_PHY_CADENCE_DPHY_RX is not set
# CONFIG_PHY_CADENCE_SALVO is not set
# CONFIG_PHY_PXA_28NM_HSIC is not set
# CONFIG_PHY_PXA_28NM_USB2 is not set
# CONFIG_PHY_LAN966X_SERDES is not set
# CONFIG_PHY_OCELOT_SERDES is not set
# end of PHY Subsystem
# CONFIG_POWERCAP is not set
# CONFIG_MCB is not set
# CONFIG_RAS is not set
#
# Android
#
# end of Android
# CONFIG_LIBNVDIMM is not set
# CONFIG_DAX is not set
# CONFIG_NVMEM is not set
#
# HW tracing support
#
# CONFIG_STM is not set
# CONFIG_INTEL_TH is not set
# end of HW tracing support
# CONFIG_FPGA is not set
# CONFIG_FSI is not set
# CONFIG_SIOX is not set
# CONFIG_SLIMBUS is not set
# CONFIG_INTERCONNECT is not set
# CONFIG_COUNTER is not set
# CONFIG_PECI is not set
# CONFIG_HTE is not set
# end of Device Drivers
#
# File systems
#
# CONFIG_VALIDATE_FS_PARSER is not setCONFIG_FS_IOMAP=yCONFIG_EXT2_FS=y
# CONFIG_EXT2_FS_XATTR is not set
# CONFIG_EXT3_FS is not set
# CONFIG_EXT4_FS is not set
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
# CONFIG_XFS_FS is not set
# CONFIG_GFS2_FS is not set
# CONFIG_BTRFS_FS is not set
# CONFIG_NILFS2_FS is not set
# CONFIG_F2FS_FS is not set
# CONFIG_EXPORTFS_BLOCK_OPS is not setCONFIG_FILE_LOCKING=y
# CONFIG_FS_ENCRYPTION is not set
# CONFIG_FS_VERITY is not set
# CONFIG_DNOTIFY is not set
# CONFIG_INOTIFY_USER is not set
# CONFIG_FANOTIFY is not set
# CONFIG_QUOTA is not set
# CONFIG_AUTOFS4_FS is not set
# CONFIG_AUTOFS_FS is not set
# CONFIG_FUSE_FS is not set
# CONFIG_OVERLAY_FS is not set
#
# Caches
#
# CONFIG_FSCACHE is not set
# end of Caches
#
# CD-ROM/DVD Filesystems
#
# CONFIG_ISO9660_FS is not set
# CONFIG_UDF_FS is not set
# end of CD-ROM/DVD Filesystems
#
# DOS/FAT/EXFAT/NT Filesystems
#
# CONFIG_MSDOS_FS is not set
# CONFIG_VFAT_FS is not set
# CONFIG_EXFAT_FS is not set
# CONFIG_NTFS_FS is not set
# CONFIG_NTFS3_FS is not set
# end of DOS/FAT/EXFAT/NT Filesystems
#
# Pseudo filesystems
#CONFIG_PROC_FS=yCONFIG_PROC_SYSCTL=y
# CONFIG_PROC_CHILDREN is not setCONFIG_KERNFS=yCONFIG_SYSFS=yCONFIG_ARCH_HAS_GIGANTIC_PAGE=y
# CONFIG_CONFIGFS_FS is not set
# end of Pseudo filesystems
# CONFIG_MISC_FILESYSTEMS is not set
# CONFIG_NLS is not set
# CONFIG_UNICODE is not set
# end of File systems
#
# Security options
#
# CONFIG_KEYS is not set
# CONFIG_SECURITY_DMESG_RESTRICT is not set
# CONFIG_SECURITY is not set
# CONFIG_SECURITYFS is not set
# CONFIG_FORTIFY_SOURCE is not set
# CONFIG_STATIC_USERMODEHELPER is not setCONFIG_DEFAULT_SECURITY_DAC=yCONFIG_LSM="[]"
#
# Kernel hardening options
#
#
# Memory initialization
#CONFIG_CC_HAS_AUTO_VAR_INIT_PATTERN=yCONFIG_CC_HAS_AUTO_VAR_INIT_ZERO_BARE=yCONFIG_CC_HAS_AUTO_VAR_INIT_ZERO=y
# CONFIG_INIT_STACK_NONE is not set
# CONFIG_INIT_STACK_ALL_PATTERN is not setCONFIG_INIT_STACK_ALL_ZERO=y
# CONFIG_INIT_ON_ALLOC_DEFAULT_ON is not set
# CONFIG_INIT_ON_FREE_DEFAULT_ON is not setCONFIG_CC_HAS_ZERO_CALL_USED_REGS=y
# CONFIG_ZERO_CALL_USED_REGS is not set
# end of Memory initialization
CONFIG_RANDSTRUCT_NONE=y
# CONFIG_RANDSTRUCT_FULL is not set
# CONFIG_RANDSTRUCT_PERFORMANCE is not set
# end of Kernel hardening options # end of Security options
# CONFIG_CRYPTO is not set
#
# Library routines
#
# CONFIG_PACKING is not setCONFIG_BITREVERSE=yCONFIG_GENERIC_STRNCPY_FROM_USER=yCONFIG_GENERIC_STRNLEN_USER=y
# CONFIG_CORDIC is not set
# CONFIG_PRIME_NUMBERS is not setCONFIG_RATIONAL=yCONFIG_GENERIC_PCI_IOMAP=y
#
# Crypto library routines
#CONFIG_CRYPTO_LIB_BLAKE2S_GENERIC=y
# CONFIG_CRYPTO_LIB_CHACHA is not set
# CONFIG_CRYPTO_LIB_CURVE25519 is not setCONFIG_CRYPTO_LIB_POLY1305_RSIZE=1
# CONFIG_CRYPTO_LIB_POLY1305 is not set
# end of Crypto library routines
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
# CONFIG_CRC_T10DIF is not set
# CONFIG_CRC64_ROCKSOFT is not set
# CONFIG_CRC_ITU_T is not setCONFIG_CRC32=y
# CONFIG_CRC32_SELFTEST is not setCONFIG_CRC32_SLICEBY8=y
# CONFIG_CRC32_SLICEBY4 is not set
# CONFIG_CRC32_SARWATE is not set
# CONFIG_CRC32_BIT is not set
# CONFIG_CRC64 is not set
# CONFIG_CRC4 is not set
# CONFIG_CRC7 is not set
# CONFIG_LIBCRC32C is not set
# CONFIG_CRC8 is not setCONFIG_XXHASH=y
# CONFIG_RANDOM32_SELFTEST is not setCONFIG_ZLIB_INFLATE=yCONFIG_ZSTD_COMMON=yCONFIG_ZSTD_DECOMPRESS=y
# CONFIG_XZ_DEC is not setCONFIG_DECOMPRESS_GZIP=yCONFIG_DECOMPRESS_ZSTD=yCONFIG_HAS_IOMEM=yCONFIG_HAS_IOPORT_MAP=yCONFIG_HAS_DMA=yCONFIG_ARCH_DMA_ADDR_T_64BIT=yCONFIG_DMA_DECLARE_COHERENT=yCONFIG_DMA_NONCOHERENT_MMAP=y
# CONFIG_DMA_API_DEBUG is not set
# CONFIG_FORCE_NR_CPUS is not set
# CONFIG_IRQ_POLL is not setCONFIG_LIBFDT=yCONFIG_SG_POOL=yCONFIG_UACCESS_MEMCPY=yCONFIG_ARCH_STACKWALK=yCONFIG_SBITMAP=y
# end of Library routines
CONFIG_GENERIC_LIB_DEVMEM_IS_ALLOWED=y
#
# Kernel hacking
#
#
# printk and dmesg options # CONFIG_PRINTK_TIME=y # CONFIG_PRINTK_CALLER is not set # CONFIG_STACKTRACE_BUILD_ID is not set CONFIG_CONSOLE_LOGLEVEL_DEFAULT=7 CONFIG_CONSOLE_LOGLEVEL_QUIET=4 CONFIG_MESSAGE_LOGLEVEL_DEFAULT=4 # CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_DYNAMIC_DEBUG is not set # CONFIG_DYNAMIC_DEBUG_CORE is not set CONFIG_SYMBOLIC_ERRNAME=y CONFIG_DEBUG_BUGVERBOSE=y # end of printk and dmesg options
CONFIG_DEBUG_KERNEL=yCONFIG_DEBUG_MISC=y
#
# Compile-time checks and compiler options
#CONFIG_DEBUG_INFO_NONE=y
# CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT is not set # CONFIG_DEBUG_INFO_DWARF4 is not set
# CONFIG_DEBUG_INFO_DWARF5 is not set CONFIG_FRAME_WARN=2048
# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_READABLE_ASM is not set
# CONFIG_HEADERS_INSTALL is not set CONFIG_DEBUG_SECTION_MISMATCH=y CONFIG_SECTION_MISMATCH_WARN_ONLY=y CONFIG_ARCH_WANT_FRAME_POINTERS=y CONFIG_FRAME_POINTER=y
# CONFIG_VMLINUX_MAP is not set
# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set
# end of Compile-time checks and compiler options
#
# Generic Kernel Debugging Instruments
#
# CONFIG_MAGIC_SYSRQ is not set
# CONFIG_DEBUG_FS is not setCONFIG_HAVE_ARCH_KGDB=yCONFIG_HAVE_ARCH_KGDB_QXFER_PKT=y
# CONFIG_KGDB is not setCONFIG_ARCH_HAS_UBSAN_SANITIZE_ALL=y
# CONFIG_UBSAN is not setCONFIG_HAVE_KCSAN_COMPILER=y
# end of Generic Kernel Debugging Instruments
#
# Networking Debugging
#
# end of Networking Debugging
#
# Memory Debugging
#
# CONFIG_PAGE_EXTENSION is not set
# CONFIG_DEBUG_PAGEALLOC is not set
# CONFIG_PAGE_OWNER is not set
# CONFIG_PAGE_POISONING is not setCONFIG_ARCH_HAS_DEBUG_WX=y
# CONFIG_DEBUG_OBJECTS is not setCONFIG_HAVE_DEBUG_KMEMLEAK=y
# CONFIG_DEBUG_KMEMLEAK is not set
# CONFIG_DEBUG_STACK_USAGE is not set
# CONFIG_SCHED_STACK_END_CHECK is not setCONFIG_ARCH_HAS_DEBUG_VM_PGTABLE=y
# CONFIG_DEBUG_VM is not set
# CONFIG_DEBUG_NOMMU_REGIONS is not set
# CONFIG_DEBUG_MEMORY_INIT is not set
# CONFIG_DEBUG_PER_CPU_MAPS is not setCONFIG_CC_HAS_KASAN_GENERIC=yCONFIG_CC_HAS_WORKING_NOSANITIZE_ADDRESS=y
# end of Memory Debugging
# CONFIG_DEBUG_SHIRQ is not set
#
# Debug Oops, Lockups and Hangs
#
# CONFIG_PANIC_ON_OOPS is not setCONFIG_PANIC_ON_OOPS_VALUE=0CONFIG_PANIC_TIMEOUT=0
# CONFIG_SOFTLOCKUP_DETECTOR is not set
# CONFIG_DETECT_HUNG_TASK is not set
# CONFIG_WQ_WATCHDOG is not set
# end of Debug Oops, Lockups and Hangs
#
# Scheduler Debugging
#
# CONFIG_SCHED_DEBUG is not set
# CONFIG_SCHEDSTATS is not set
# end of Scheduler Debugging
# CONFIG_DEBUG_TIMEKEEPING is not set
#
# Lock Debugging (spinlocks, mutexes, etc...)
#CONFIG_LOCK_DEBUGGING_SUPPORT=y
# CONFIG_PROVE_LOCKING is not set
# CONFIG_LOCK_STAT is not set
# CONFIG_DEBUG_RT_MUTEXES is not set
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_MUTEXES is not set
# CONFIG_DEBUG_WW_MUTEX_SLOWPATH is not set
# CONFIG_DEBUG_RWSEMS is not set
# CONFIG_DEBUG_LOCK_ALLOC is not set
# CONFIG_DEBUG_ATOMIC_SLEEP is not set
# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
# CONFIG_LOCK_TORTURE_TEST is not set
# CONFIG_WW_MUTEX_SELFTEST is not set
# CONFIG_SCF_TORTURE_TEST is not set
# CONFIG_CSD_LOCK_WAIT_DEBUG is not set
# end of Lock Debugging (spinlocks, mutexes, etc...)
# CONFIG_DEBUG_IRQFLAGS is not set
# CONFIG_STACKTRACE is not set
# CONFIG_WARN_ALL_UNSEEDED_RANDOM is not set
# CONFIG_DEBUG_KOBJECT is not set
#
# Debug kernel data structures
#
# CONFIG_DEBUG_LIST is not set
# CONFIG_DEBUG_PLIST is not set
# CONFIG_DEBUG_SG is not set
# CONFIG_DEBUG_NOTIFIERS is not set
# CONFIG_BUG_ON_DATA_CORRUPTION is not set
# CONFIG_DEBUG_MAPLE_TREE is not set
# end of Debug kernel data structures
# CONFIG_DEBUG_CREDENTIALS is not set
#
# RCU Debugging
#
# CONFIG_RCU_SCALE_TEST is not set
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_RCU_REF_SCALE_TEST is not setCONFIG_RCU_CPU_STALL_TIMEOUT=21CONFIG_RCU_EXP_CPU_STALL_TIMEOUT=0
# CONFIG_RCU_TRACE is not set
# CONFIG_RCU_EQS_DEBUG is not set
# end of RCU Debugging
# CONFIG_DEBUG_WQ_FORCE_RR_CPU is not set
# CONFIG_LATENCYTOP is not setCONFIG_HAVE_FUNCTION_TRACER=yCONFIG_HAVE_FUNCTION_GRAPH_TRACER=yCONFIG_HAVE_FTRACE_MCOUNT_RECORD=yCONFIG_HAVE_SYSCALL_TRACEPOINTS=yCONFIG_TRACING_SUPPORT=y
# CONFIG_FTRACE is not set
# CONFIG_SAMPLES is not set
#
# riscv Debugging # # end of riscv Debugging
#
# Kernel Testing and Coverage
#
# CONFIG_KUNIT is not set
# CONFIG_NOTIFIER_ERROR_INJECTION is not set
# CONFIG_FAULT_INJECTION is not setCONFIG_ARCH_HAS_KCOV=yCONFIG_CC_HAS_SANCOV_TRACE_PC=y
# CONFIG_KCOV is not set
# CONFIG_RUNTIME_TESTING_MENU is not setCONFIG_ARCH_USE_MEMTEST=y
# CONFIG_MEMTEST is not set
# end of Kernel Testing and Coverage
#
# Rust hacking
#
# end of Rust hacking # end of Kernel hacking
kernel test robot
build botI love your patch! Yet something to improve:
Hi,
I love your patch! Yet something to improve:
[auto build test ERROR on linus/master]
[also build test ERROR on v6.1-rc4 next-20221108]
[If your patch is applied to the wrong git tree, kindly drop us a note. And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch#_base_tree_information]
url: https://github.com/intel-lab-lkp/linux/commits/guoren-kernel-org/riscv-asid-Fixup-stale-TLB-entry-cause-application-crash/20221108-182151 patch link: https://lore.kernel.org/r/20221108102044.3317793-1-guoren%40kernel.org patch subject: [PATCH RESEND] riscv: asid: Fixup stale TLB entry cause application crash config: riscv-nommu_k210_defconfig compiler: riscv64-linux-gcc (GCC) 12.1.0
reproduce (this is a W=1 build):
wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross chmod +x ~/bin/make.cross
# https://github.com/intel-lab-lkp/linux/commit/025af39c1eb149e584705dfc72ac117812c82f3e
git remote add linux-review https://github.com/intel-lab-lkp/linux
git fetch --no-tags linux-review guoren-kernel-org/riscv-asid-Fixup-stale-TLB-entry-cause-application-crash/20221108-182151 git checkout 025af39c1eb149e584705dfc72ac117812c82f3e
# save the config file
mkdir build_dir && cp config build_dir/.config
COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-12.1.0 make.cross W=1 O=build_dir ARCH=riscv SHELL=/bin/bash
If you fix the issue, kindly add following tag where applicable | Reported-by: kernel test robot <[email protected]>
All errors (new ones prefixed by >>):
riscv64-linux-ld: arch/riscv/mm/context.o: in function `.L0 ':
>> context.c:(.text+0x2e): undefined reference to `use_asid_allocator'
Signature · 2 lines
0-DAY CI Kernel Test Service https://01.org/lkp
#
# Automatically generated file; DO NOT EDIT.
# Linux/riscv 6.1.0-rc4 Kernel Configuration
#CONFIG_CC_VERSION_TEXT="riscv64-linux-gcc (GCC) 12.1.0" CONFIG_CC_IS_GCC=yCONFIG_GCC_VERSION=120100 CONFIG_CLANG_VERSION=0CONFIG_AS_IS_GNU=yCONFIG_AS_VERSION=23800CONFIG_LD_IS_BFD=yCONFIG_LD_VERSION=23800CONFIG_LLD_VERSION=0 CONFIG_CC_HAS_ASM_GOTO_OUTPUT=y CONFIG_CC_HAS_ASM_INLINE=y CONFIG_CC_HAS_NO_PROFILE_FN_ATTR=y CONFIG_PAHOLE_VERSION=123CONFIG_IRQ_WORK=yCONFIG_THREAD_INFO_IN_TASK=y
#
# General setup
#CONFIG_INIT_ENV_ARG_LIMIT=32
# CONFIG_COMPILE_TEST is not set
# CONFIG_WERROR is not setCONFIG_LOCALVERSION=""CONFIG_LOCALVERSION_AUTO=yCONFIG_BUILD_SALT=""CONFIG_DEFAULT_INIT=""CONFIG_DEFAULT_HOSTNAME="(none)"
# CONFIG_SYSVIPC is not set
# CONFIG_WATCH_QUEUE is not set
# CONFIG_USELIB is not setCONFIG_HAVE_ARCH_AUDITSYSCALL=y
#
# IRQ subsystem
#CONFIG_GENERIC_IRQ_SHOW=yCONFIG_GENERIC_IRQ_SHOW_LEVEL=yCONFIG_GENERIC_IRQ_EFFECTIVE_AFF_MASK=yCONFIG_HARDIRQS_SW_RESEND=yCONFIG_IRQ_DOMAIN=yCONFIG_IRQ_DOMAIN_HIERARCHY=yCONFIG_IRQ_FORCED_THREADING=yCONFIG_SPARSE_IRQ=y
# end of IRQ subsystem
CONFIG_GENERIC_IRQ_MULTI_HANDLER=yCONFIG_ARCH_CLOCKSOURCE_INIT=yCONFIG_GENERIC_CLOCKEVENTS=yCONFIG_ARCH_HAS_TICK_BROADCAST=yCONFIG_GENERIC_CLOCKEVENTS_BROADCAST=yCONFIG_HAVE_POSIX_CPU_TIMERS_TASK_WORK=yCONFIG_POSIX_CPU_TIMERS_TASK_WORK=yCONFIG_CONTEXT_TRACKING=yCONFIG_CONTEXT_TRACKING_IDLE=y
#
# Timers subsystem
#CONFIG_HZ_PERIODIC=y
# CONFIG_NO_HZ_IDLE is not set
# CONFIG_NO_HZ_FULL is not set
# CONFIG_NO_HZ is not set
# CONFIG_HIGH_RES_TIMERS is not set
# end of Timers subsystem
#
# BPF subsystem
#
# CONFIG_BPF_SYSCALL is not set
# end of BPF subsystem
CONFIG_PREEMPT_NONE_BUILD=yCONFIG_PREEMPT_NONE=y
# CONFIG_PREEMPT_VOLUNTARY is not set
# CONFIG_PREEMPT is not set
#
# CPU/Task time and stats accounting
#CONFIG_TICK_CPU_ACCOUNTING=y
# CONFIG_VIRT_CPU_ACCOUNTING_GEN is not set
# CONFIG_IRQ_TIME_ACCOUNTING is not set
# CONFIG_BSD_PROCESS_ACCT is not set
# CONFIG_PSI is not set
# end of CPU/Task time and stats accounting
# CONFIG_CPU_ISOLATION is not set
#
# RCU Subsystem
#CONFIG_TREE_RCU=y
# CONFIG_RCU_EXPERT is not setCONFIG_SRCU=yCONFIG_TREE_SRCU=yCONFIG_RCU_STALL_COMMON=yCONFIG_RCU_NEED_SEGCBLIST=y
# end of RCU Subsystem
# CONFIG_IKCONFIG is not set
# CONFIG_IKHEADERS is not setCONFIG_LOG_BUF_SHIFT=13CONFIG_LOG_CPU_MAX_BUF_SHIFT=12CONFIG_PRINTK_SAFE_LOG_BUF_SHIFT=12CONFIG_GENERIC_SCHED_CLOCK=y
#
# Scheduler features
#
# end of Scheduler features
CONFIG_CC_HAS_INT128=y CONFIG_CC_IMPLICIT_FALLTHROUGH="-Wimplicit-fallthrough=5" CONFIG_GCC12_NO_ARRAY_BOUNDS=y CONFIG_CC_NO_ARRAY_BOUNDS=y CONFIG_ARCH_SUPPORTS_INT128=y
# CONFIG_CGROUPS is not set
# CONFIG_NAMESPACES is not set
# CONFIG_CHECKPOINT_RESTORE is not set
# CONFIG_SCHED_AUTOGROUP is not set
# CONFIG_SYSFS_DEPRECATED is not set
# CONFIG_RELAY is not set CONFIG_BLK_DEV_INITRD=y CONFIG_INITRAMFS_SOURCE=""
# CONFIG_INITRAMFS_FORCE is not set
# CONFIG_RD_GZIP is not set
# CONFIG_RD_BZIP2 is not set
# CONFIG_RD_LZMA is not set
# CONFIG_RD_XZ is not set
# CONFIG_RD_LZO is not set
# CONFIG_RD_LZ4 is not set
# CONFIG_RD_ZSTD is not set
# CONFIG_BOOT_CONFIG is not set CONFIG_INITRAMFS_PRESERVE_MTIME=y
# CONFIG_CC_OPTIMIZE_FOR_PERFORMANCE is not set CONFIG_CC_OPTIMIZE_FOR_SIZE=yCONFIG_SYSCTL=yCONFIG_SYSCTL_EXCEPTION_TRACE=yCONFIG_EXPERT=yCONFIG_MULTIUSER=y
# CONFIG_SGETMASK_SYSCALL is not set
# CONFIG_SYSFS_SYSCALL is not set
# CONFIG_FHANDLE is not set CONFIG_POSIX_TIMERS=yCONFIG_PRINTK=yCONFIG_BUG=y
# CONFIG_BASE_FULL is not set
# CONFIG_FUTEX is not set
# CONFIG_EPOLL is not set
# CONFIG_SIGNALFD is not set
# CONFIG_TIMERFD is not set
# CONFIG_EVENTFD is not set
# CONFIG_AIO is not set
# CONFIG_IO_URING is not set
# CONFIG_ADVISE_SYSCALLS is not set CONFIG_MEMBARRIER=y
# CONFIG_KALLSYMS is not set
# CONFIG_KCMP is not setCONFIG_RSEQ=y
# CONFIG_DEBUG_RSEQ is not setCONFIG_EMBEDDED=yCONFIG_HAVE_PERF_EVENTS=y
# CONFIG_PC104 is not set
#
# Kernel Performance Events And Counters
#
# CONFIG_PERF_EVENTS is not set
# end of Kernel Performance Events And Counters
# CONFIG_PROFILING is not set
# end of General setup
CONFIG_64BIT=yCONFIG_RISCV=yCONFIG_ARCH_MMAP_RND_BITS_MIN=18CONFIG_ARCH_MMAP_RND_COMPAT_BITS_MIN=8CONFIG_ARCH_MMAP_RND_BITS_MAX=24CONFIG_ARCH_MMAP_RND_COMPAT_BITS_MAX=17CONFIG_RISCV_M_MODE=y
# CONFIG_MMU is not setCONFIG_PAGE_OFFSET=0x80000000CONFIG_ARCH_FLATMEM_ENABLE=yCONFIG_ARCH_SUPPORTS_UPROBES=yCONFIG_STACKTRACE_SUPPORT=yCONFIG_GENERIC_BUG=yCONFIG_GENERIC_BUG_RELATIVE_POINTERS=yCONFIG_GENERIC_CALIBRATE_DELAY=yCONFIG_GENERIC_CSUM=yCONFIG_GENERIC_HWEIGHT=yCONFIG_PGTABLE_LEVELS=5CONFIG_LOCKDEP_SUPPORT=yCONFIG_AS_HAS_INSN=y
#
# SoC selection
#
# CONFIG_SOC_MICROCHIP_POLARFIRE is not set
# CONFIG_SOC_SIFIVE is not set
# CONFIG_SOC_STARFIVE is not set
# CONFIG_SOC_VIRT is not setCONFIG_SOC_CANAAN=yCONFIG_SOC_CANAAN_K210_DTB_BUILTIN=yCONFIG_SOC_CANAAN_K210_DTB_SOURCE="k210_generic"
# end of SoC selection
#
# CPU errata selection
#
# CONFIG_ERRATA_SIFIVE is not set
# CONFIG_ERRATA_THEAD is not set
# end of CPU errata selection
#
# Platform type
#CONFIG_NONPORTABLE=y
# CONFIG_ARCH_RV32I is not setCONFIG_ARCH_RV64I=y
# CONFIG_CMODEL_MEDLOW is not setCONFIG_CMODEL_MEDANY=yCONFIG_SMP=yCONFIG_NR_CPUS=2
# CONFIG_HOTPLUG_CPU is not setCONFIG_TUNE_GENERIC=yCONFIG_RISCV_ISA_C=yCONFIG_TOOLCHAIN_HAS_ZIHINTPAUSE=yCONFIG_FPU=y
# end of Platform type
#
# Kernel features
#
# CONFIG_HZ_100 is not setCONFIG_HZ_250=y
# CONFIG_HZ_300 is not set
# CONFIG_HZ_1000 is not setCONFIG_HZ=250CONFIG_RISCV_BOOT_SPINWAIT=y
# CONFIG_KEXEC_FILE is not set
# CONFIG_CRASH_DUMP is not set
# end of Kernel features
#
# Boot options
#CONFIG_CMDLINE="earlycon console=ttySIF0"
# CONFIG_CMDLINE_FALLBACK is not set
# CONFIG_CMDLINE_EXTEND is not setCONFIG_CMDLINE_FORCE=yCONFIG_CC_HAVE_STACKPROTECTOR_TLS=y
# CONFIG_PHYS_RAM_BASE_FIXED is not set
# end of Boot options
CONFIG_BUILTIN_DTB=y
#
# Power management options
#CONFIG_PM=y
# CONFIG_PM_DEBUG is not setCONFIG_PM_CLK=y
# CONFIG_WQ_POWER_EFFICIENT_DEFAULT is not set
# end of Power management options
#
# CPU Power Management
#
#
# CPU Idle
#
# CONFIG_CPU_IDLE is not set
# end of CPU Idle # end of CPU Power Management
# CONFIG_VIRTUALIZATION is not set
#
# General architecture-dependent options
#
# CONFIG_JUMP_LABEL is not setCONFIG_HAVE_64BIT_ALIGNED_ACCESS=yCONFIG_HAVE_KPROBES=yCONFIG_HAVE_KRETPROBES=yCONFIG_HAVE_KPROBES_ON_FTRACE=yCONFIG_HAVE_FUNCTION_ERROR_INJECTION=yCONFIG_TRACE_IRQFLAGS_SUPPORT=yCONFIG_HAVE_ARCH_TRACEHOOK=yCONFIG_GENERIC_SMP_IDLE_THREAD=yCONFIG_GENERIC_IDLE_POLL_SETUP=yCONFIG_ARCH_HAS_FORTIFY_SOURCE=yCONFIG_HAVE_ARCH_THREAD_STRUCT_WHITELIST=yCONFIG_HAVE_ASM_MODVERSIONS=yCONFIG_HAVE_REGS_AND_STACK_ACCESS_API=yCONFIG_HAVE_RSEQ=yCONFIG_HAVE_FUNCTION_ARG_ACCESS_API=yCONFIG_HAVE_PERF_REGS=yCONFIG_HAVE_PERF_USER_STACK_DUMP=yCONFIG_HAVE_ARCH_JUMP_LABEL=yCONFIG_HAVE_ARCH_JUMP_LABEL_RELATIVE=yCONFIG_HAVE_ARCH_SECCOMP=yCONFIG_HAVE_ARCH_SECCOMP_FILTER=y
# CONFIG_SECCOMP is not setCONFIG_HAVE_STACKPROTECTOR=y
# CONFIG_STACKPROTECTOR is not setCONFIG_LTO_NONE=yCONFIG_HAVE_CONTEXT_TRACKING_USER=yCONFIG_HAVE_VIRT_CPU_ACCOUNTING_GEN=yCONFIG_HAVE_IRQ_TIME_ACCOUNTING=yCONFIG_HAVE_MOVE_PUD=yCONFIG_HAVE_MOVE_PMD=yCONFIG_ARCH_WANT_HUGE_PMD_SHARE=yCONFIG_PAGE_SIZE_LESS_THAN_64KB=yCONFIG_PAGE_SIZE_LESS_THAN_256KB=yCONFIG_CLONE_BACKWARDS=y
# CONFIG_COMPAT_32BIT_TIME is not setCONFIG_ARCH_OPTIONAL_KERNEL_RWX_DEFAULT=y
#
# GCOV-based kernel profiling
#CONFIG_ARCH_HAS_GCOV_PROFILE_ALL=y
# end of GCOV-based kernel profiling
CONFIG_HAVE_GCC_PLUGINS=y
# CONFIG_GCC_PLUGINS is not set
# end of General architecture-dependent options
CONFIG_RT_MUTEXES=yCONFIG_BASE_SMALL=1
# CONFIG_MODULES is not set
# CONFIG_BLOCK is not setCONFIG_INLINE_SPIN_UNLOCK_IRQ=yCONFIG_INLINE_READ_UNLOCK=yCONFIG_INLINE_READ_UNLOCK_IRQ=yCONFIG_INLINE_WRITE_UNLOCK=yCONFIG_INLINE_WRITE_UNLOCK_IRQ=yCONFIG_ARCH_SUPPORTS_ATOMIC_RMW=yCONFIG_MUTEX_SPIN_ON_OWNER=yCONFIG_RWSEM_SPIN_ON_OWNER=yCONFIG_LOCK_SPIN_ON_OWNER=yCONFIG_ARCH_USE_QUEUED_RWLOCKS=yCONFIG_QUEUED_RWLOCKS=yCONFIG_ARCH_HAS_MMIOWB=yCONFIG_MMIOWB=y
#
# Executable file formats
#CONFIG_BINFMT_SCRIPT=yCONFIG_ARCH_HAS_BINFMT_FLAT=yCONFIG_BINFMT_FLAT=yCONFIG_BINFMT_FLAT_NO_DATA_START_OFFSET=y
# CONFIG_BINFMT_FLAT_OLD is not set
# CONFIG_BINFMT_ZFLAT is not set
# CONFIG_BINFMT_MISC is not set
# CONFIG_COREDUMP is not set
# end of Executable file formats
#
# Memory Management options
#
#
# SLAB allocator options
#
# CONFIG_SLAB is not set
# CONFIG_SLUB is not setCONFIG_SLOB=y
# end of SLAB allocator options
# CONFIG_SHUFFLE_PAGE_ALLOCATOR is not set
# CONFIG_COMPAT_BRK is not set
# CONFIG_MMAP_ALLOW_UNINITIALIZED is not setCONFIG_FLATMEM=yCONFIG_EXCLUSIVE_SYSTEM_RAM=yCONFIG_SPLIT_PTLOCK_CPUS=999999CONFIG_ARCH_ENABLE_SPLIT_PMD_PTLOCK=y
# CONFIG_PAGE_REPORTING is not setCONFIG_PHYS_ADDR_T_64BIT=yCONFIG_NOMMU_INITIAL_TRIM_EXCESS=1CONFIG_ARCH_WANT_GENERAL_HUGETLB=yCONFIG_NEED_PER_CPU_KM=yCONFIG_GENERIC_EARLY_IOREMAP=yCONFIG_ARCH_HAS_CURRENT_STACK_POINTER=yCONFIG_ZONE_DMA32=y
# CONFIG_VM_EVENT_COUNTERS is not set
# CONFIG_PERCPU_STATS is not set
#
# GUP_TEST needs to have DEBUG_FS enabled
#CONFIG_ARCH_HAS_PTE_SPECIAL=y
#
# Data Access Monitoring
#
# CONFIG_DAMON is not set
# end of Data Access Monitoring # end of Memory Management options
# CONFIG_NET is not set
#
# Device Drivers
#CONFIG_HAVE_PCI=y
# CONFIG_PCI is not set
# CONFIG_PCCARD is not set
#
# Generic Driver Options
#
# CONFIG_UEVENT_HELPER is not setCONFIG_DEVTMPFS=yCONFIG_DEVTMPFS_MOUNT=y
# CONFIG_DEVTMPFS_SAFE is not setCONFIG_STANDALONE=yCONFIG_PREVENT_FIRMWARE_BUILD=y
#
# Firmware loader
#
# CONFIG_FW_LOADER is not set
# end of Firmware loader
# CONFIG_ALLOW_DEV_COREDUMP is not set
# CONFIG_DEBUG_DRIVER is not set
# CONFIG_DEBUG_DEVRES is not set
# CONFIG_DEBUG_TEST_DRIVER_REMOVE is not setCONFIG_REGMAP=yCONFIG_REGMAP_MMIO=yCONFIG_GENERIC_ARCH_TOPOLOGY=y
# end of Generic Driver Options
#
# Bus devices
#
# CONFIG_MOXTET is not set
# CONFIG_MHI_BUS is not set
# CONFIG_MHI_BUS_EP is not set
# end of Bus devices
#
# Firmware Drivers
#
#
# ARM System Control and Management Interface Protocol #
# end of ARM System Control and Management Interface Protocol
# CONFIG_FIRMWARE_MEMMAP is not set
# CONFIG_GOOGLE_FIRMWARE is not set
#
# Tegra firmware driver
#
# end of Tegra firmware driver # end of Firmware Drivers
# CONFIG_GNSS is not set
# CONFIG_MTD is not setCONFIG_DTC=yCONFIG_OF=y
# CONFIG_OF_UNITTEST is not setCONFIG_OF_FLATTREE=yCONFIG_OF_EARLY_FLATTREE=yCONFIG_OF_KOBJ=yCONFIG_OF_ADDRESS=yCONFIG_OF_IRQ=yCONFIG_OF_RESERVED_MEM=y
# CONFIG_OF_OVERLAY is not setCONFIG_OF_DMA_DEFAULT_COHERENT=y
# CONFIG_PARPORT is not set
#
# NVME Support
#
# end of NVME Support
#
# Misc devices
#
# CONFIG_AD525X_DPOT is not set
# CONFIG_DUMMY_IRQ is not set
# CONFIG_ICS932S401 is not set
# CONFIG_ENCLOSURE_SERVICES is not set
# CONFIG_APDS9802ALS is not set
# CONFIG_ISL29003 is not set
# CONFIG_ISL29020 is not set
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_SENSORS_BH1770 is not set
# CONFIG_SENSORS_APDS990X is not set
# CONFIG_HMC6352 is not set
# CONFIG_DS1682 is not set
# CONFIG_LATTICE_ECP3_CONFIG is not set
# CONFIG_SRAM is not set
# CONFIG_XILINX_SDFEC is not set
# CONFIG_OPEN_DICE is not set
# CONFIG_VCPU_STALL_DETECTOR is not set
# CONFIG_C2PORT is not set
#
# EEPROM support
#
# CONFIG_EEPROM_AT24 is not set
# CONFIG_EEPROM_AT25 is not set
# CONFIG_EEPROM_LEGACY is not set
# CONFIG_EEPROM_MAX6875 is not set
# CONFIG_EEPROM_93CX6 is not set
# CONFIG_EEPROM_93XX46 is not set
# CONFIG_EEPROM_IDT_89HPESX is not set
# CONFIG_EEPROM_EE1004 is not set
# end of EEPROM support
#
# Texas Instruments shared transport line discipline #
# end of Texas Instruments shared transport line discipline
# CONFIG_ALTERA_STAPL is not set
# CONFIG_ECHO is not set
# CONFIG_PVPANIC is not set
# end of Misc devices
#
# SCSI device support
#
# end of SCSI device support
#
# Input device support
#
# CONFIG_INPUT is not set
#
# Hardware I/O ports
#
# CONFIG_SERIO is not set
# CONFIG_GAMEPORT is not set
# end of Hardware I/O ports # end of Input device support
#
# Character devices
#CONFIG_TTY=y
# CONFIG_VT is not set
# CONFIG_UNIX98_PTYS is not set
# CONFIG_LEGACY_PTYS is not set
# CONFIG_LDISC_AUTOLOAD is not set
#
# Serial drivers
#CONFIG_SERIAL_EARLYCON=y
# CONFIG_SERIAL_8250 is not set
#
# Non-8250 serial port support
#
# CONFIG_SERIAL_MAX3100 is not set
# CONFIG_SERIAL_MAX310X is not set
# CONFIG_SERIAL_UARTLITE is not setCONFIG_SERIAL_CORE=yCONFIG_SERIAL_CORE_CONSOLE=yCONFIG_SERIAL_SIFIVE=yCONFIG_SERIAL_SIFIVE_CONSOLE=y
# CONFIG_SERIAL_SCCNXP is not set
# CONFIG_SERIAL_SC16IS7XX is not set
# CONFIG_SERIAL_ALTERA_JTAGUART is not set
# CONFIG_SERIAL_ALTERA_UART is not set
# CONFIG_SERIAL_XILINX_PS_UART is not set
# CONFIG_SERIAL_ARC is not set
# CONFIG_SERIAL_FSL_LPUART is not set
# CONFIG_SERIAL_FSL_LINFLEXUART is not set
# CONFIG_SERIAL_CONEXANT_DIGICOLOR is not set
# CONFIG_SERIAL_SPRD is not set
# end of Serial drivers
# CONFIG_SERIAL_NONSTANDARD is not set
# CONFIG_NULL_TTY is not set
# CONFIG_SERIAL_DEV_BUS is not set
# CONFIG_TTY_PRINTK is not set
# CONFIG_VIRTIO_CONSOLE is not set
# CONFIG_IPMI_HANDLER is not set
# CONFIG_HW_RANDOM is not set
# CONFIG_DEVMEM is not set
# CONFIG_TCG_TPM is not set
# CONFIG_XILLYBUS is not setCONFIG_RANDOM_TRUST_CPU=yCONFIG_RANDOM_TRUST_BOOTLOADER=y
# end of Character devices
#
# I2C support
#CONFIG_I2C=yCONFIG_I2C_BOARDINFO=y
# CONFIG_I2C_COMPAT is not setCONFIG_I2C_CHARDEV=y
# CONFIG_I2C_MUX is not set
# CONFIG_I2C_HELPER_AUTO is not set
# CONFIG_I2C_SMBUS is not set
#
# I2C Algorithms
#
# CONFIG_I2C_ALGOBIT is not set
# CONFIG_I2C_ALGOPCF is not set
# CONFIG_I2C_ALGOPCA is not set
# end of I2C Algorithms
#
# I2C Hardware Bus support
#
#
# I2C system bus drivers (mostly embedded / system-on-chip) #
# CONFIG_I2C_CBUS_GPIO is not set CONFIG_I2C_DESIGNWARE_CORE=y
# CONFIG_I2C_DESIGNWARE_SLAVE is not set CONFIG_I2C_DESIGNWARE_PLATFORM=y
# CONFIG_I2C_EMEV2 is not set
# CONFIG_I2C_GPIO is not set
# CONFIG_I2C_OCORES is not set
# CONFIG_I2C_PCA_PLATFORM is not set
# CONFIG_I2C_RK3X is not set
# CONFIG_I2C_SIMTEC is not set
# CONFIG_I2C_XILINX is not set
#
# External I2C/SMBus adapter drivers
#
# CONFIG_I2C_TAOS_EVM is not set
#
# Other I2C/SMBus bus drivers
#
# CONFIG_I2C_VIRTIO is not set
# end of I2C Hardware Bus support
# CONFIG_I2C_SLAVE is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# end of I2C support
# CONFIG_I3C is not setCONFIG_SPI=y
# CONFIG_SPI_DEBUG is not setCONFIG_SPI_MASTER=y
# CONFIG_SPI_MEM is not set
#
# SPI Master Controller Drivers
#
# CONFIG_SPI_ALTERA is not set
# CONFIG_SPI_AXI_SPI_ENGINE is not set
# CONFIG_SPI_BITBANG is not set
# CONFIG_SPI_CADENCE is not setCONFIG_SPI_DESIGNWARE=y
# CONFIG_SPI_DW_DMA is not setCONFIG_SPI_DW_MMIO=y
# CONFIG_SPI_NXP_FLEXSPI is not set
# CONFIG_SPI_GPIO is not set
# CONFIG_SPI_FSL_SPI is not set
# CONFIG_SPI_MICROCHIP_CORE is not set
# CONFIG_SPI_MICROCHIP_CORE_QSPI is not set
# CONFIG_SPI_OC_TINY is not set
# CONFIG_SPI_ROCKCHIP is not set
# CONFIG_SPI_SC18IS602 is not set
# CONFIG_SPI_SIFIVE is not set
# CONFIG_SPI_MXIC is not set
# CONFIG_SPI_XCOMM is not set
# CONFIG_SPI_XILINX is not set
# CONFIG_SPI_ZYNQMP_GQSPI is not set
# CONFIG_SPI_AMD is not set
#
# SPI Multiplexer support
#
# CONFIG_SPI_MUX is not set
#
# SPI Protocol Masters
#
# CONFIG_SPI_SPIDEV is not set
# CONFIG_SPI_TLE62X0 is not set
# CONFIG_SPI_SLAVE is not set
# CONFIG_SPMI is not set
# CONFIG_HSI is not set
# CONFIG_PPS is not set
#
# PTP clock support
#CONFIG_PTP_1588_CLOCK_OPTIONAL=y
#
# Enable PHYLIB and NETWORK_PHY_TIMESTAMPING to see the additional clocks. #
# end of PTP clock support
CONFIG_PINCTRL=yCONFIG_PINMUX=yCONFIG_GENERIC_PINMUX_FUNCTIONS=yCONFIG_PINCONF=yCONFIG_GENERIC_PINCONF=y
# CONFIG_DEBUG_PINCTRL is not set
# CONFIG_PINCTRL_CY8C95X0 is not setCONFIG_PINCTRL_K210=y
# CONFIG_PINCTRL_MCP23S08 is not set
# CONFIG_PINCTRL_MICROCHIP_SGPIO is not set
# CONFIG_PINCTRL_OCELOT is not set
# CONFIG_PINCTRL_SINGLE is not set
# CONFIG_PINCTRL_STMFX is not set
# CONFIG_PINCTRL_SX150X is not set
#
# Renesas pinctrl drivers
#
# end of Renesas pinctrl drivers
CONFIG_GPIOLIB=yCONFIG_GPIOLIB_FASTPATH_LIMIT=512CONFIG_OF_GPIO=yCONFIG_GPIOLIB_IRQCHIP=y
# CONFIG_DEBUG_GPIO is not set
# CONFIG_GPIO_SYSFS is not setCONFIG_GPIO_CDEV=y
# CONFIG_GPIO_CDEV_V1 is not setCONFIG_GPIO_GENERIC=y
#
# Memory mapped GPIO drivers
#
# CONFIG_GPIO_74XX_MMIO is not set
# CONFIG_GPIO_ALTERA is not set
# CONFIG_GPIO_CADENCE is not setCONFIG_GPIO_DWAPB=y
# CONFIG_GPIO_FTGPIO010 is not set
# CONFIG_GPIO_GENERIC_PLATFORM is not set
# CONFIG_GPIO_GRGPIO is not set
# CONFIG_GPIO_HLWD is not set
# CONFIG_GPIO_LOGICVC is not set
# CONFIG_GPIO_MB86S7X is not setCONFIG_GPIO_SIFIVE=y
# CONFIG_GPIO_SYSCON is not set
# CONFIG_GPIO_XILINX is not set
# CONFIG_GPIO_AMD_FCH is not set
# end of Memory mapped GPIO drivers
#
# I2C GPIO expanders
#
# CONFIG_GPIO_ADNP is not set
# CONFIG_GPIO_GW_PLD is not set
# CONFIG_GPIO_MAX7300 is not set
# CONFIG_GPIO_MAX732X is not set
# CONFIG_GPIO_PCA953X is not set
# CONFIG_GPIO_PCA9570 is not set
# CONFIG_GPIO_PCF857X is not set
# CONFIG_GPIO_TPIC2810 is not set
# end of I2C GPIO expanders
#
# MFD GPIO expanders
#
# end of MFD GPIO expanders
#
# SPI GPIO expanders
#
# CONFIG_GPIO_74X164 is not set
# CONFIG_GPIO_MAX3191X is not set
# CONFIG_GPIO_MAX7301 is not set
# CONFIG_GPIO_MC33880 is not set
# CONFIG_GPIO_PISOSR is not set
# CONFIG_GPIO_XRA1403 is not set
# end of SPI GPIO expanders
#
# Virtual GPIO drivers
#
# CONFIG_GPIO_AGGREGATOR is not set
# CONFIG_GPIO_MOCKUP is not set
# CONFIG_GPIO_SIM is not set
# end of Virtual GPIO drivers
# CONFIG_W1 is not setCONFIG_POWER_RESET=y
# CONFIG_POWER_RESET_GPIO is not set
# CONFIG_POWER_RESET_GPIO_RESTART is not set
# CONFIG_POWER_RESET_LTC2952 is not set
# CONFIG_POWER_RESET_RESTART is not setCONFIG_POWER_RESET_SYSCON=y
# CONFIG_POWER_RESET_SYSCON_POWEROFF is not set
# CONFIG_SYSCON_REBOOT_MODE is not set
# CONFIG_NVMEM_REBOOT_MODE is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
# CONFIG_THERMAL is not set
# CONFIG_WATCHDOG is not setCONFIG_SSB_POSSIBLE=y
# CONFIG_SSB is not setCONFIG_BCMA_POSSIBLE=y
# CONFIG_BCMA is not set
#
# Multifunction device drivers
#
# CONFIG_MFD_ACT8945A is not set
# CONFIG_MFD_AS3711 is not set
# CONFIG_MFD_AS3722 is not set
# CONFIG_PMIC_ADP5520 is not set
# CONFIG_MFD_AAT2870_CORE is not set
# CONFIG_MFD_ATMEL_FLEXCOM is not set
# CONFIG_MFD_ATMEL_HLCDC is not set
# CONFIG_MFD_BCM590XX is not set
# CONFIG_MFD_BD9571MWV is not set
# CONFIG_MFD_AXP20X_I2C is not set
# CONFIG_MFD_MADERA is not set
# CONFIG_PMIC_DA903X is not set
# CONFIG_MFD_DA9052_SPI is not set
# CONFIG_MFD_DA9052_I2C is not set
# CONFIG_MFD_DA9055 is not set
# CONFIG_MFD_DA9062 is not set
# CONFIG_MFD_DA9063 is not set
# CONFIG_MFD_DA9150 is not set
# CONFIG_MFD_GATEWORKS_GSC is not set
# CONFIG_MFD_MC13XXX_SPI is not set
# CONFIG_MFD_MC13XXX_I2C is not set
# CONFIG_MFD_MP2629 is not set
# CONFIG_MFD_HI6421_PMIC is not set
# CONFIG_HTC_PASIC3 is not set
# CONFIG_HTC_I2CPLD is not set
# CONFIG_MFD_IQS62X is not set
# CONFIG_MFD_KEMPLD is not set
# CONFIG_MFD_88PM800 is not set
# CONFIG_MFD_88PM805 is not set
# CONFIG_MFD_88PM860X is not set
# CONFIG_MFD_MAX14577 is not set
# CONFIG_MFD_MAX77620 is not set
# CONFIG_MFD_MAX77650 is not set
# CONFIG_MFD_MAX77686 is not set
# CONFIG_MFD_MAX77693 is not set
# CONFIG_MFD_MAX77714 is not set
# CONFIG_MFD_MAX77843 is not set
# CONFIG_MFD_MAX8907 is not set
# CONFIG_MFD_MAX8925 is not set
# CONFIG_MFD_MAX8997 is not set
# CONFIG_MFD_MAX8998 is not set
# CONFIG_MFD_MT6360 is not set
# CONFIG_MFD_MT6370 is not set
# CONFIG_MFD_MT6397 is not set
# CONFIG_MFD_MENF21BMC is not set
# CONFIG_MFD_OCELOT is not set
# CONFIG_EZX_PCAP is not set
# CONFIG_MFD_CPCAP is not set
# CONFIG_MFD_NTXEC is not set
# CONFIG_MFD_RETU is not set
# CONFIG_MFD_PCF50633 is not set
# CONFIG_MFD_SY7636A is not set
# CONFIG_MFD_RT4831 is not set
# CONFIG_MFD_RT5033 is not set
# CONFIG_MFD_RT5120 is not set
# CONFIG_MFD_RC5T583 is not set
# CONFIG_MFD_RK808 is not set
# CONFIG_MFD_RN5T618 is not set
# CONFIG_MFD_SEC_CORE is not set
# CONFIG_MFD_SI476X_CORE is not set
# CONFIG_MFD_SM501 is not set
# CONFIG_MFD_SKY81452 is not set
# CONFIG_MFD_STMPE is not setCONFIG_MFD_SYSCON=y
# CONFIG_MFD_TI_AM335X_TSCADC is not set
# CONFIG_MFD_LP3943 is not set
# CONFIG_MFD_LP8788 is not set
# CONFIG_MFD_TI_LMU is not set
# CONFIG_MFD_PALMAS is not set
# CONFIG_TPS6105X is not set
# CONFIG_TPS65010 is not set
# CONFIG_TPS6507X is not set
# CONFIG_MFD_TPS65086 is not set
# CONFIG_MFD_TPS65090 is not set
# CONFIG_MFD_TPS65217 is not set
# CONFIG_MFD_TI_LP873X is not set
# CONFIG_MFD_TI_LP87565 is not set
# CONFIG_MFD_TPS65218 is not set
# CONFIG_MFD_TPS6586X is not set
# CONFIG_MFD_TPS65910 is not set
# CONFIG_MFD_TPS65912_I2C is not set
# CONFIG_MFD_TPS65912_SPI is not set
# CONFIG_TWL4030_CORE is not set
# CONFIG_TWL6040_CORE is not set
# CONFIG_MFD_WL1273_CORE is not set
# CONFIG_MFD_LM3533 is not set
# CONFIG_MFD_TC3589X is not set
# CONFIG_MFD_TQMX86 is not set
# CONFIG_MFD_LOCHNAGAR is not set
# CONFIG_MFD_ARIZONA_I2C is not set
# CONFIG_MFD_ARIZONA_SPI is not set
# CONFIG_MFD_WM8400 is not set
# CONFIG_MFD_WM831X_I2C is not set
# CONFIG_MFD_WM831X_SPI is not set
# CONFIG_MFD_WM8350_I2C is not set
# CONFIG_MFD_WM8994 is not set
# CONFIG_MFD_ROHM_BD718XX is not set
# CONFIG_MFD_ROHM_BD71828 is not set
# CONFIG_MFD_ROHM_BD957XMUF is not set
# CONFIG_MFD_STPMIC1 is not set
# CONFIG_MFD_STMFX is not set
# CONFIG_MFD_ATC260X_I2C is not set
# CONFIG_MFD_QCOM_PM8008 is not set
# CONFIG_MFD_INTEL_M10_BMC is not set
# CONFIG_MFD_RSMU_I2C is not set
# CONFIG_MFD_RSMU_SPI is not set
# end of Multifunction device drivers
# CONFIG_REGULATOR is not set
#
# CEC support
#
# CONFIG_MEDIA_CEC_SUPPORT is not set
# end of CEC support
# CONFIG_MEDIA_SUPPORT is not set
#
# Graphics support
#
# CONFIG_DRM is not set
# CONFIG_DRM_DEBUG_MODESET_LOCK is not set
#
# ARM devices
#
# end of ARM devices
#
# Frame buffer Devices
#
# CONFIG_FB is not set
# end of Frame buffer Devices
#
# Backlight & LCD device support
#
# CONFIG_LCD_CLASS_DEVICE is not set
# CONFIG_BACKLIGHT_CLASS_DEVICE is not set
# end of Backlight & LCD device support # end of Graphics support
# CONFIG_SOUND is not setCONFIG_USB_OHCI_LITTLE_ENDIAN=y
# CONFIG_USB_SUPPORT is not set
# CONFIG_MMC is not set
# CONFIG_MEMSTICK is not setCONFIG_NEW_LEDS=yCONFIG_LEDS_CLASS=y
# CONFIG_LEDS_CLASS_FLASH is not set
# CONFIG_LEDS_CLASS_MULTICOLOR is not set
# CONFIG_LEDS_BRIGHTNESS_HW_CHANGED is not set
#
# LED drivers
#
# CONFIG_LEDS_AN30259A is not set
# CONFIG_LEDS_AW2013 is not set
# CONFIG_LEDS_BCM6328 is not set
# CONFIG_LEDS_BCM6358 is not set
# CONFIG_LEDS_CR0014114 is not set
# CONFIG_LEDS_EL15203000 is not set
# CONFIG_LEDS_LM3530 is not set
# CONFIG_LEDS_LM3532 is not set
# CONFIG_LEDS_LM3642 is not set
# CONFIG_LEDS_LM3692X is not setCONFIG_LEDS_GPIO=y
# CONFIG_LEDS_LP3944 is not set
# CONFIG_LEDS_LP3952 is not set
# CONFIG_LEDS_LP55XX_COMMON is not set
# CONFIG_LEDS_LP8860 is not set
# CONFIG_LEDS_PCA955X is not set
# CONFIG_LEDS_PCA963X is not set
# CONFIG_LEDS_DAC124S085 is not set
# CONFIG_LEDS_BD2802 is not set
# CONFIG_LEDS_LT3593 is not set
# CONFIG_LEDS_TCA6507 is not set
# CONFIG_LEDS_TLC591XX is not set
# CONFIG_LEDS_LM355x is not set
# CONFIG_LEDS_IS31FL319X is not set
# CONFIG_LEDS_IS31FL32XX is not set
#
# LED driver for blink(1) USB RGB LED is under Special HID drivers (HID_THINGM) #
# CONFIG_LEDS_BLINKM is not set
# CONFIG_LEDS_SYSCON is not set
# CONFIG_LEDS_MLXREG is not setCONFIG_LEDS_USER=y
# CONFIG_LEDS_SPI_BYTE is not set
# CONFIG_LEDS_TI_LMU_COMMON is not set
#
# Flash and Torch LED drivers
#
#
# RGB LED drivers
#
#
# LED Triggers
#
# CONFIG_LEDS_TRIGGERS is not set
#
# Simple LED drivers
#
# CONFIG_ACCESSIBILITY is not setCONFIG_EDAC_SUPPORT=y
# CONFIG_RTC_CLASS is not set
# CONFIG_DMADEVICES is not set
#
# DMABUF options
#
# CONFIG_SYNC_FILE is not set
# CONFIG_DMABUF_HEAPS is not set
# end of DMABUF options
# CONFIG_AUXDISPLAY is not set
# CONFIG_VFIO is not set
# CONFIG_VIRT_DRIVERS is not set
# CONFIG_VIRTIO_MENU is not set
# CONFIG_VHOST_MENU is not set
#
# Microsoft Hyper-V guest support
#
# end of Microsoft Hyper-V guest support
# CONFIG_GREYBUS is not set
# CONFIG_COMEDI is not set
# CONFIG_STAGING is not set
# CONFIG_GOLDFISH is not setCONFIG_HAVE_CLK=yCONFIG_HAVE_CLK_PREPARE=yCONFIG_COMMON_CLK=y
# CONFIG_LMK04832 is not set
# CONFIG_COMMON_CLK_MAX9485 is not set
# CONFIG_COMMON_CLK_SI5341 is not set
# CONFIG_COMMON_CLK_SI5351 is not set
# CONFIG_COMMON_CLK_SI514 is not set
# CONFIG_COMMON_CLK_SI544 is not set
# CONFIG_COMMON_CLK_SI570 is not set
# CONFIG_COMMON_CLK_CDCE706 is not set
# CONFIG_COMMON_CLK_CDCE925 is not set
# CONFIG_COMMON_CLK_CS2000_CP is not set
# CONFIG_COMMON_CLK_AXI_CLKGEN is not set
# CONFIG_COMMON_CLK_RS9_PCIE is not set
# CONFIG_COMMON_CLK_VC5 is not set
# CONFIG_COMMON_CLK_VC7 is not set
# CONFIG_COMMON_CLK_FIXED_MMIO is not setCONFIG_COMMON_CLK_K210=y
# CONFIG_XILINX_VCU is not set
# CONFIG_COMMON_CLK_XLNX_CLKWZRD is not set
# CONFIG_HWSPINLOCK is not set
#
# Clock Source drivers
#CONFIG_TIMER_OF=yCONFIG_TIMER_PROBE=yCONFIG_CLINT_TIMER=y
# CONFIG_MICROCHIP_PIT64B is not set
# end of Clock Source drivers
# CONFIG_MAILBOX is not set
#
# Remoteproc drivers
#
# CONFIG_REMOTEPROC is not set
# end of Remoteproc drivers
#
# Rpmsg drivers
#
# CONFIG_RPMSG_VIRTIO is not set
# end of Rpmsg drivers
# CONFIG_SOUNDWIRE is not set
#
# SOC (System On Chip) specific Drivers
#
#
# Amlogic SoC drivers
#
# end of Amlogic SoC drivers
#
# Broadcom SoC drivers
#
# end of Broadcom SoC drivers
CONFIG_SOC_K210_SYSCTL=y
#
# NXP/Freescale QorIQ SoC drivers
#
# end of NXP/Freescale QorIQ SoC drivers
#
# fujitsu SoC drivers # # end of fujitsu SoC drivers
#
# i.MX SoC drivers
#
# end of i.MX SoC drivers
#
# Enable LiteX SoC Builder specific drivers
#
# CONFIG_LITEX_SOC_CONTROLLER is not set
# end of Enable LiteX SoC Builder specific drivers
#
# Qualcomm SoC drivers
#
# end of Qualcomm SoC drivers
# CONFIG_SOC_TI is not set
#
# Xilinx SoC drivers
#
# end of Xilinx SoC drivers # end of SOC (System On Chip) specific Drivers
# CONFIG_PM_DEVFREQ is not set
# CONFIG_EXTCON is not set
# CONFIG_MEMORY is not set
# CONFIG_IIO is not set
# CONFIG_PWM is not set
#
# IRQ chip support
#CONFIG_IRQCHIP=y
# CONFIG_AL_FIC is not set
# CONFIG_XILINX_INTC is not setCONFIG_RISCV_INTC=yCONFIG_SIFIVE_PLIC=y
# end of IRQ chip support
# CONFIG_IPACK_BUS is not setCONFIG_ARCH_HAS_RESET_CONTROLLER=yCONFIG_RESET_CONTROLLER=yCONFIG_RESET_K210=y
# CONFIG_RESET_SIMPLE is not set
# CONFIG_RESET_TI_SYSCON is not set
# CONFIG_RESET_TI_TPS380X is not set
#
# PHY Subsystem
#
# CONFIG_GENERIC_PHY is not set
# CONFIG_PHY_CAN_TRANSCEIVER is not set
#
# PHY drivers for Broadcom platforms
#
# CONFIG_BCM_KONA_USB2_PHY is not set
# end of PHY drivers for Broadcom platforms
# CONFIG_PHY_CADENCE_TORRENT is not set
# CONFIG_PHY_CADENCE_DPHY is not set
# CONFIG_PHY_CADENCE_DPHY_RX is not set
# CONFIG_PHY_CADENCE_SIERRA is not set
# CONFIG_PHY_CADENCE_SALVO is not set
# CONFIG_PHY_PXA_28NM_HSIC is not set
# CONFIG_PHY_PXA_28NM_USB2 is not set
# CONFIG_PHY_LAN966X_SERDES is not set
# CONFIG_PHY_OCELOT_SERDES is not set
# end of PHY Subsystem
# CONFIG_POWERCAP is not set
# CONFIG_MCB is not set
# CONFIG_RAS is not set
#
# Android
#
# end of Android
# CONFIG_DAX is not set
# CONFIG_NVMEM is not set
#
# HW tracing support
#
# CONFIG_STM is not set
# CONFIG_INTEL_TH is not set
# end of HW tracing support
# CONFIG_FPGA is not set
# CONFIG_FSI is not set
# CONFIG_SIOX is not set
# CONFIG_SLIMBUS is not set
# CONFIG_INTERCONNECT is not set
# CONFIG_COUNTER is not set
# CONFIG_PECI is not set
# CONFIG_HTE is not set
# end of Device Drivers
#
# File systems
#
# CONFIG_VALIDATE_FS_PARSER is not set
# CONFIG_EXPORTFS_BLOCK_OPS is not set
# CONFIG_FILE_LOCKING is not set
# CONFIG_FS_ENCRYPTION is not set
# CONFIG_FS_VERITY is not set
# CONFIG_DNOTIFY is not set
# CONFIG_INOTIFY_USER is not set
# CONFIG_FANOTIFY is not set
# CONFIG_QUOTA is not set
# CONFIG_AUTOFS4_FS is not set
# CONFIG_AUTOFS_FS is not set
# CONFIG_FUSE_FS is not set
# CONFIG_OVERLAY_FS is not set
#
# Caches
#
# CONFIG_FSCACHE is not set
# end of Caches
#
# Pseudo filesystems
#CONFIG_PROC_FS=yCONFIG_PROC_SYSCTL=y
# CONFIG_PROC_CHILDREN is not setCONFIG_KERNFS=yCONFIG_SYSFS=yCONFIG_ARCH_HAS_GIGANTIC_PAGE=y
# CONFIG_CONFIGFS_FS is not set
# end of Pseudo filesystems
# CONFIG_MISC_FILESYSTEMS is not set
# CONFIG_NLS is not set
# CONFIG_UNICODE is not set
# end of File systems
#
# Security options
#
# CONFIG_KEYS is not set
# CONFIG_SECURITY_DMESG_RESTRICT is not set
# CONFIG_SECURITY is not set
# CONFIG_SECURITYFS is not set
# CONFIG_FORTIFY_SOURCE is not set
# CONFIG_STATIC_USERMODEHELPER is not setCONFIG_DEFAULT_SECURITY_DAC=yCONFIG_LSM="[]"
#
# Kernel hardening options
#
#
# Memory initialization
#CONFIG_CC_HAS_AUTO_VAR_INIT_PATTERN=yCONFIG_CC_HAS_AUTO_VAR_INIT_ZERO_BARE=yCONFIG_CC_HAS_AUTO_VAR_INIT_ZERO=y
# CONFIG_INIT_STACK_NONE is not set
# CONFIG_INIT_STACK_ALL_PATTERN is not setCONFIG_INIT_STACK_ALL_ZERO=y
# CONFIG_INIT_ON_ALLOC_DEFAULT_ON is not set
# CONFIG_INIT_ON_FREE_DEFAULT_ON is not setCONFIG_CC_HAS_ZERO_CALL_USED_REGS=y
# CONFIG_ZERO_CALL_USED_REGS is not set
# end of Memory initialization
CONFIG_RANDSTRUCT_NONE=y
# end of Kernel hardening options # end of Security options
# CONFIG_CRYPTO is not set
#
# Library routines
#
# CONFIG_PACKING is not setCONFIG_BITREVERSE=yCONFIG_GENERIC_STRNCPY_FROM_USER=yCONFIG_GENERIC_STRNLEN_USER=y
# CONFIG_CORDIC is not set
# CONFIG_PRIME_NUMBERS is not setCONFIG_RATIONAL=yCONFIG_GENERIC_PCI_IOMAP=y
#
# Crypto library routines
#CONFIG_CRYPTO_LIB_BLAKE2S_GENERIC=y
# CONFIG_CRYPTO_LIB_CHACHA is not set
# CONFIG_CRYPTO_LIB_CURVE25519 is not setCONFIG_CRYPTO_LIB_POLY1305_RSIZE=1
# CONFIG_CRYPTO_LIB_POLY1305 is not set
# end of Crypto library routines
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
# CONFIG_CRC_T10DIF is not set
# CONFIG_CRC64_ROCKSOFT is not set
# CONFIG_CRC_ITU_T is not setCONFIG_CRC32=y
# CONFIG_CRC32_SELFTEST is not setCONFIG_CRC32_SLICEBY8=y
# CONFIG_CRC32_SLICEBY4 is not set
# CONFIG_CRC32_SARWATE is not set
# CONFIG_CRC32_BIT is not set
# CONFIG_CRC64 is not set
# CONFIG_CRC4 is not set
# CONFIG_CRC7 is not set
# CONFIG_LIBCRC32C is not set
# CONFIG_CRC8 is not set
# CONFIG_RANDOM32_SELFTEST is not set
# CONFIG_XZ_DEC is not setCONFIG_HAS_IOMEM=yCONFIG_HAS_IOPORT_MAP=yCONFIG_HAS_DMA=yCONFIG_ARCH_DMA_ADDR_T_64BIT=yCONFIG_DMA_DECLARE_COHERENT=yCONFIG_DMA_NONCOHERENT_MMAP=y
# CONFIG_DMA_API_DEBUG is not set
# CONFIG_FORCE_NR_CPUS is not set
# CONFIG_IRQ_POLL is not setCONFIG_LIBFDT=yCONFIG_UACCESS_MEMCPY=yCONFIG_ARCH_STACKWALK=y
# end of Library routines
CONFIG_GENERIC_LIB_DEVMEM_IS_ALLOWED=y
#
# Kernel hacking
#
#
# printk and dmesg options # CONFIG_PRINTK_TIME=y # CONFIG_PRINTK_CALLER is not set # CONFIG_STACKTRACE_BUILD_ID is not set CONFIG_CONSOLE_LOGLEVEL_DEFAULT=7 CONFIG_CONSOLE_LOGLEVEL_QUIET=4 CONFIG_MESSAGE_LOGLEVEL_DEFAULT=4 # CONFIG_BOOT_PRINTK_DELAY is not set # CONFIG_DYNAMIC_DEBUG is not set # CONFIG_DYNAMIC_DEBUG_CORE is not set # CONFIG_SYMBOLIC_ERRNAME is not set # CONFIG_DEBUG_BUGVERBOSE is not set # end of printk and dmesg options
CONFIG_DEBUG_KERNEL=y
# CONFIG_DEBUG_MISC is not set
#
# Compile-time checks and compiler options
#CONFIG_DEBUG_INFO_NONE=y
# CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT is not set # CONFIG_DEBUG_INFO_DWARF4 is not set
# CONFIG_DEBUG_INFO_DWARF5 is not set CONFIG_FRAME_WARN=2048
# CONFIG_STRIP_ASM_SYMS is not set
# CONFIG_READABLE_ASM is not set
# CONFIG_HEADERS_INSTALL is not set CONFIG_DEBUG_SECTION_MISMATCH=y CONFIG_SECTION_MISMATCH_WARN_ONLY=y CONFIG_ARCH_WANT_FRAME_POINTERS=y
# CONFIG_FRAME_POINTER is not set
# CONFIG_VMLINUX_MAP is not set
# CONFIG_DEBUG_FORCE_WEAK_PER_CPU is not set
# end of Compile-time checks and compiler options
#
# Generic Kernel Debugging Instruments
#
# CONFIG_MAGIC_SYSRQ is not set
# CONFIG_DEBUG_FS is not setCONFIG_HAVE_ARCH_KGDB=yCONFIG_HAVE_ARCH_KGDB_QXFER_PKT=y
# CONFIG_KGDB is not setCONFIG_ARCH_HAS_UBSAN_SANITIZE_ALL=y
# CONFIG_UBSAN is not setCONFIG_HAVE_KCSAN_COMPILER=y
# end of Generic Kernel Debugging Instruments
#
# Networking Debugging
#
# end of Networking Debugging
#
# Memory Debugging
#
# CONFIG_PAGE_EXTENSION is not set
# CONFIG_DEBUG_PAGEALLOC is not set
# CONFIG_PAGE_OWNER is not set
# CONFIG_PAGE_POISONING is not setCONFIG_ARCH_HAS_DEBUG_WX=y
# CONFIG_DEBUG_OBJECTS is not setCONFIG_HAVE_DEBUG_KMEMLEAK=y
# CONFIG_DEBUG_KMEMLEAK is not set
# CONFIG_DEBUG_STACK_USAGE is not set
# CONFIG_SCHED_STACK_END_CHECK is not setCONFIG_ARCH_HAS_DEBUG_VM_PGTABLE=y
# CONFIG_DEBUG_VM is not set
# CONFIG_DEBUG_NOMMU_REGIONS is not set
# CONFIG_DEBUG_MEMORY_INIT is not set
# CONFIG_DEBUG_PER_CPU_MAPS is not setCONFIG_CC_HAS_KASAN_GENERIC=yCONFIG_CC_HAS_WORKING_NOSANITIZE_ADDRESS=y
# end of Memory Debugging
# CONFIG_DEBUG_SHIRQ is not set
#
# Debug Oops, Lockups and Hangs
#CONFIG_PANIC_ON_OOPS=yCONFIG_PANIC_ON_OOPS_VALUE=1CONFIG_PANIC_TIMEOUT=0
# CONFIG_SOFTLOCKUP_DETECTOR is not set
# CONFIG_DETECT_HUNG_TASK is not set
# CONFIG_WQ_WATCHDOG is not set
# end of Debug Oops, Lockups and Hangs
#
# Scheduler Debugging
#
# CONFIG_SCHED_DEBUG is not set
# CONFIG_SCHEDSTATS is not set
# end of Scheduler Debugging
# CONFIG_DEBUG_TIMEKEEPING is not set
#
# Lock Debugging (spinlocks, mutexes, etc...)
#CONFIG_LOCK_DEBUGGING_SUPPORT=y
# CONFIG_PROVE_LOCKING is not set
# CONFIG_LOCK_STAT is not set
# CONFIG_DEBUG_RT_MUTEXES is not set
# CONFIG_DEBUG_SPINLOCK is not set
# CONFIG_DEBUG_MUTEXES is not set
# CONFIG_DEBUG_WW_MUTEX_SLOWPATH is not set
# CONFIG_DEBUG_RWSEMS is not set
# CONFIG_DEBUG_LOCK_ALLOC is not set
# CONFIG_DEBUG_ATOMIC_SLEEP is not set
# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
# CONFIG_LOCK_TORTURE_TEST is not set
# CONFIG_WW_MUTEX_SELFTEST is not set
# CONFIG_SCF_TORTURE_TEST is not set
# CONFIG_CSD_LOCK_WAIT_DEBUG is not set
# end of Lock Debugging (spinlocks, mutexes, etc...)
# CONFIG_DEBUG_IRQFLAGS is not set
# CONFIG_STACKTRACE is not set
# CONFIG_WARN_ALL_UNSEEDED_RANDOM is not set
# CONFIG_DEBUG_KOBJECT is not set
#
# Debug kernel data structures
#
# CONFIG_DEBUG_LIST is not set
# CONFIG_DEBUG_PLIST is not set
# CONFIG_DEBUG_SG is not set
# CONFIG_DEBUG_NOTIFIERS is not set
# CONFIG_BUG_ON_DATA_CORRUPTION is not set
# CONFIG_DEBUG_MAPLE_TREE is not set
# end of Debug kernel data structures
# CONFIG_DEBUG_CREDENTIALS is not set
#
# RCU Debugging
#
# CONFIG_RCU_SCALE_TEST is not set
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_RCU_REF_SCALE_TEST is not setCONFIG_RCU_CPU_STALL_TIMEOUT=21CONFIG_RCU_EXP_CPU_STALL_TIMEOUT=0
# CONFIG_RCU_TRACE is not set
# CONFIG_RCU_EQS_DEBUG is not set
# end of RCU Debugging
# CONFIG_DEBUG_WQ_FORCE_RR_CPU is not setCONFIG_HAVE_FUNCTION_TRACER=yCONFIG_HAVE_FUNCTION_GRAPH_TRACER=yCONFIG_HAVE_FTRACE_MCOUNT_RECORD=yCONFIG_HAVE_SYSCALL_TRACEPOINTS=yCONFIG_TRACING_SUPPORT=y
# CONFIG_FTRACE is not set
# CONFIG_SAMPLES is not set
#
# riscv Debugging # # end of riscv Debugging
#
# Kernel Testing and Coverage
#
# CONFIG_KUNIT is not set
# CONFIG_NOTIFIER_ERROR_INJECTION is not set
# CONFIG_FAULT_INJECTION is not setCONFIG_ARCH_HAS_KCOV=yCONFIG_CC_HAS_SANCOV_TRACE_PC=y
# CONFIG_KCOV is not set
# CONFIG_RUNTIME_TESTING_MENU is not setCONFIG_ARCH_USE_MEMTEST=y
# CONFIG_MEMTEST is not set
# end of Kernel Testing and Coverage
#
# Rust hacking
#
# end of Rust hacking # end of Kernel hacking