ASoC: Fixes for WM8940 codec
Subsystems (3)
cover ASoC: Fixes for WM8940 codec
This patch series provides fixes for WM8940 codec.
The most notable change is the clock rewrite, so this driver now can either generate proper clock frequency by itself or use one provided from the clock subsystem of the SoC.
Lukasz Majewski (4):
ASoC: wm8940: Remove warning when no plat data present
ASoC: wm8940: Rewrite code to set proper clocks
ASoC: wm8940: Mute also the speaker output
ASoC: wm8940: Read chip ID when wm8940 codec probing
sound/soc/codecs/wm8940.c | 129 +++++++++++++++++++++++++++++++------- sound/soc/codecs/wm8940.h | 6 ++ 2 files changed, 111 insertions(+), 24 deletions(-)
Signature · 1 line
2.20.1
PATCH 1/4 ASoC: wm8940: Remove warning when no plat data present
The lack of platform data in the contemporary Linux shall not be the reason to display warnings to the kernel logs.
--- sound/soc/codecs/wm8940.c | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-)
sound/soc/codecs/wm8940.c +1 -3
@@ -709,9 +709,7 @@ static int wm8940_probe(struct snd_soc_component *component)if (ret <0 )return ret; -if (!pdata) -dev_warn (component->dev,"No platform data supplied\n" ); -else { +if (pdata) { reg =snd_soc_component_read (component,WM8940_OUTPUTCTL ); ret =snd_soc_component_write (component,WM8940_OUTPUTCTL , reg | pdata->vroi);if (ret <0 )
Signature · 1 line
2.20.1
Re: [PATCH 1/4] ASoC: wm8940: Remove warning when no plat data present
Quoted 6 lines · Lukasz Majewski
The lack of platform data in the contemporary Linux shall not be the reason to display warnings to the kernel logs.
Signed-off-by Lukasz Majewski <[email protected]>---
Thanks,
Charles
PATCH 2/4 ASoC: wm8940: Rewrite code to set proper clocks
In reply to Lukasz MajewskiWithout this change, the wm8940 driver is not working when set_sysclk callback (wm8940_set_dai_sysclk) is called with frequency not listed in the switch clause.
This change adjusts this driver to allow non-standard frequency set (just after the boot) being adjusted afterwards by the sound system core code.
Moreover, support for internal wm8940's PLL is provided, so it can generate clocks when HOST system is not able to do it.
Code in this commit is based on previous change done for wm8974 (SHA1: 51b2bb3f2568e6d9d81a001d38b8d70c2ba4af99).
--- sound/soc/codecs/wm8940.c | 103 ++++++++++++++++++++++++++++++-------- 1 file changed, 83 insertions(+), 20 deletions(-)
sound/soc/codecs/wm8940.c +83 -20
@@ -37,7 +37,9 @@#include "wm8940.h" struct wm8940_priv { -unsigned int sysclk; +unsigned int mclk; +unsigned int fs; +struct regmap *regmap; };
@@ -387,17 +389,24 @@ static int wm8940_set_dai_fmt(struct snd_soc_dai *codec_dai,return 0 ; } +static int wm8940_update_clocks (struct snd_soc_dai *dai);static int wm8940_i2s_hw_params (struct snd_pcm_substream *substream,struct snd_pcm_hw_params *params,struct snd_soc_dai *dai) {struct snd_soc_component *component = dai->component; +struct wm8940_priv *priv =snd_soc_component_get_drvdata (component);u16 iface =snd_soc_component_read (component,WM8940_IFACE ) &0xFD9F ;u16 addcntrl =snd_soc_component_read (component,WM8940_ADDCNTRL ) &0xFFF1 ;u16 companding =snd_soc_component_read (component,WM8940_COMPANDINGCTL ) &0xFFDF ;int ret; + priv->fs =params_rate (params); + ret =wm8940_update_clocks (dai); +if (ret) +return ret; +/* LoutR control */ if (substream->stream ==SNDRV_PCM_STREAM_CAPTURE &¶ms_channels (params) ==2 )
@@ -496,7 +505,6 @@ static int wm8940_set_bias_level(struct snd_soc_component *component,return ret; } } -/* ensure bufioen and biasen */ pwr_reg |= (1 <<2 ) | (1 <<3 );/* set vmid to 300k for standby */
@@ -611,24 +619,6 @@ static int wm8940_set_dai_pll(struct snd_soc_dai *codec_dai, int pll_id,return 0 ; } -static int wm8940_set_dai_sysclk (struct snd_soc_dai *codec_dai, -int clk_id,unsigned int freq,int dir) -{ -struct snd_soc_component *component = codec_dai->component; -struct wm8940_priv *wm8940 =snd_soc_component_get_drvdata (component); - -switch (freq) { -case 11289600 : -case 12000000 : -case 12288000 : -case 16934400 : -case 18432000 : - wm8940->sysclk = freq; -return 0 ; - } -return -EINVAL ; -} -static int wm8940_set_dai_clkdiv (struct snd_soc_dai *codec_dai,int div_id,int div) {
@@ -653,6 +643,79 @@ static int wm8940_set_dai_clkdiv(struct snd_soc_dai *codec_dai,return ret; } +static unsigned int wm8940_get_mclkdiv (unsigned int f_in,unsigned int f_out, +int *mclkdiv) +{ +unsigned int ratio =2 * f_in / f_out; + +if (ratio <=2 ) { + *mclkdiv =WM8940_MCLKDIV_1 ; + ratio =2 ; + }else if (ratio ==3 ) { + *mclkdiv =WM8940_MCLKDIV_1_5 ; + }else if (ratio ==4 ) { + *mclkdiv =WM8940_MCLKDIV_2 ; + }else if (ratio <=6 ) { + *mclkdiv =WM8940_MCLKDIV_3 ; + ratio =6 ; + }else if (ratio <=8 ) { + *mclkdiv =WM8940_MCLKDIV_4 ; + ratio =8 ; + }else if (ratio <=12 ) { + *mclkdiv =WM8940_MCLKDIV_6 ; + ratio =12 ; + }else if (ratio <=16 ) { + *mclkdiv =WM8940_MCLKDIV_8 ; + ratio =16 ; + }else { + *mclkdiv =WM8940_MCLKDIV_12 ; + ratio =24 ; + } + +return f_out * ratio /2 ; +} + +static int wm8940_update_clocks (struct snd_soc_dai *dai) +{ +struct snd_soc_component *codec = dai->component; +struct wm8940_priv *priv =snd_soc_component_get_drvdata (codec); +unsigned int fs256; +unsigned int fpll =0 ; +unsigned int f; +int mclkdiv; + +if (!priv->mclk || !priv->fs) +return 0 ; + + fs256 =256 * priv->fs; + + f =wm8940_get_mclkdiv (priv->mclk, fs256, &mclkdiv); +if (f != priv->mclk) { +/* The PLL performs best around 90MHz */ + fpll =wm8940_get_mclkdiv (22500000 , fs256, &mclkdiv); + } + +wm8940_set_dai_pll (dai,0 ,0 , priv->mclk, fpll); +wm8940_set_dai_clkdiv (dai,WM8940_MCLKDIV , mclkdiv); + +return 0 ; +} + +static int wm8940_set_dai_sysclk (struct snd_soc_dai *dai,int clk_id, +unsigned int freq,int dir) +{ +struct snd_soc_component *codec = dai->component; +struct wm8940_priv *priv =snd_soc_component_get_drvdata (codec); + +if (dir !=SND_SOC_CLOCK_IN ) +return -EINVAL ; + + priv->mclk = freq; + +return wm8940_update_clocks (dai); +} + +#define WM8940_RATES SNDRV_PCM_RATE_8000_48000#define WM8940_FORMATS (SNDRV_PCM_FMTBIT_S8 | \
Signature · 1 line
2.20.1
Re: [PATCH 2/4] ASoC: wm8940: Rewrite code to set proper clocks
Quoted 19 lines · Lukasz Majewski
Without this change, the wm8940 driver is not working when
set_sysclkcallback (wm8940_set_dai_sysclk) is called with frequency not listed in the switch clause.This change adjusts this driver to allow non-standard frequency set (just after the boot) being adjusted afterwards by the sound system core code.
Moreover, support for internal wm8940's PLL is provided, so it can generate clocks when HOST system is not able to do it.
Code in this commit is based on previous change done for wm8974 (SHA1:
51b2bb3f2568e6d9d81a001d38b8d70c2ba4af99).Signed-off-by Lukasz Majewski <[email protected]>---
sound/soc/codecs/wm8940.c +1
-0struct snd_soc_component *component = dai->component; +struct wm8940_priv *priv =snd_soc_component_get_drvdata (component);u16 iface =snd_soc_component_read (component,WM8940_IFACE ) &0xFD9F ;
sound/soc/codecs/wm8940.c static int wm8940_set_dai_fmt(struct snd_soc_dai *codec_dai, · line 409
Quoted 10 lines
sound/soc/codecs/wm8940.c +5
-0u16 addcntrl =snd_soc_component_read (component,WM8940_ADDCNTRL ) &0xFFF1 ;u16 companding =snd_soc_component_read (component,WM8940_COMPANDINGCTL ) &0xFFDF ;int ret; + priv->fs =params_rate (params); + ret =wm8940_update_clocks (dai); +if (ret) +return ret; +
I think this all looks mostly good, my only slight concern would be the interaction with the manual functions for settings the PLL etc. I guess under this code, whatever manual settings were configured will be overwritten with the new auto settings, I think this should be fine as the PLL wants to be run in a pretty narrow band anyway, so the settings are likely identical. Do you have any thoughts?
Thanks,
Charles
Re: [PATCH 2/4] ASoC: wm8940: Rewrite code to set proper clocks
Hi Charles,
Quoted 25 lines · Lukasz Majewski
Quoted 24 lines
Without this change, the wm8940 driver is not working when
set_sysclkcallback (wm8940_set_dai_sysclk) is called with frequency not listed in the switch clause.This change adjusts this driver to allow non-standard frequency set (just after the boot) being adjusted afterwards by the sound system core code.
Moreover, support for internal wm8940's PLL is provided, so it can generate clocks when HOST system is not able to do it.
Code in this commit is based on previous change done for wm8974 (SHA1:
51b2bb3f2568e6d9d81a001d38b8d70c2ba4af99).Signed-off-by Lukasz Majewski <[email protected]>---
(quoted diff) +1
-0struct snd_soc_component *component = dai->component; + struct wm8940_priv *priv =
snd_soc_component_get_drvdata(component); u16 iface =snd_soc_component_read(component, WM8940_IFACE)&0xFD9F; u16 addcntrl =snd_soc_component_read(component, WM8940_ADDCNTRL)&0xFFF1; u16 companding =snd_soc_component_read(component, WM8940_COMPANDINGCTL)&0xFFDF; int ret;
Quoted 10 lines
sound/soc/codecs/wm8940.c static int wm8940_set_dai_fmt(struct snd_soc_dai *codec_dai, · line 409
Quoted 5 lines
sound/soc/codecs/wm8940.c +5
-0+ priv->fs =params_rate (params); + ret =wm8940_update_clocks (dai); +if (ret) +return ret; +I think this all looks mostly good, my only slight concern would be the interaction with the manual functions for settings the PLL etc. I guess under this code, whatever manual settings were configured
At least on my system - those settings are not set manually. Everythig is done in the kernel.
This is important, as I do may use several other wm89* codecs, which drivers are inserted as modules.
Quoted 4 lines
will be overwritten with the new auto settings, I think this should be fine as the PLL wants to be run in a pretty narrow band anyway, so the settings are likely identical. Do you have any thoughts?
This code just follows changes done for WM8974 codec. I would leave the code as it is in this patch.
Quoted 3 lines
Thanks,
Charles
Best regards,
Lukasz Majewski
--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: [email protected]
Mark Brown
maintainerRe: [PATCH 2/4] ASoC: wm8940: Rewrite code to set proper clocks
In reply to Lukasz MajewskiQuoted 3 lines · Lukasz Majewski
Without this change, the wm8940 driver is not working when
set_sysclkcallback (wm8940_set_dai_sysclk) is called with frequency not listed in the switch clause.
Your commit log doesn't actually describe what this change is...
Quoted 3 lines
This change adjusts this driver to allow non-standard frequency set (just after the boot) being adjusted afterwards by the sound system core code.
This doesn't appear to correspond to the commit. The change will result in the driver automatically configuring it's PLL.
Quoted 2 lines
Code in this commit is based on previous change done for wm8974 (SHA1:
51b2bb3f2568e6d9d81a001d38b8d70c2ba4af99).
Please include human readable descriptions of things like commits and issues being discussed in e-mail in your mails, this makes them much easier for humans to read especially when they have no internet access. I do frequently catch up on my mail on flights or while otherwise travelling so this is even more pressing for me than just being about making things a bit easier to read.
sound/soc/codecs/wm8940.c static int wm8940_set_bias_level(struct snd_soc_component *component, · line 510
Quoted 8 lines
sound/soc/codecs/wm8940.c +0
-1@@ -496,7 +505,6 @@ static int wm8940_set_bias_level(struct snd_soc_component *component,return ret; } } -/* ensure bufioen and biasen */ pwr_reg |= (1 <<2 ) | (1 <<3 );/* set vmid to 300k for standby */
Unrelated (and questionable) whitespace change.
Re: [PATCH 2/4] ASoC: wm8940: Rewrite code to set proper clocks
Hi Mark,
Quoted 6 lines · Lukasz Majewski
Quoted 4 lines
Without this change, the wm8940 driver is not working when
set_sysclkcallback (wm8940_set_dai_sysclk) is called with frequency not listed in the switch clause.
Quoted 9 lines
Your commit log doesn't actually describe what this change is...
Quoted 3 lines
This change adjusts this driver to allow non-standard frequency set (just after the boot) being adjusted afterwards by the sound system core code.
This doesn't appear to correspond to the commit. The change will result in the driver automatically configuring it's PLL.
Yes, indeed - I will update the description.
The problem with the old code was that after boot up - the frequency was not in the 'switch' values, so the driver aborted in early init.
Quoted 9 lines
Quoted 2 lines
Code in this commit is based on previous change done for wm8974 (SHA1:
51b2bb3f2568e6d9d81a001d38b8d70c2ba4af99).Please include human readable descriptions of things like commits and issues being discussed in e-mail in your mails, this makes them much easier for humans to read especially when they have no internet access. I do frequently catch up on my mail on flights or while otherwise travelling so this is even more pressing for me than just being about making things a bit easier to read.
Ok. I will provide proper description.
Quoted 11 lines
sound/soc/codecs/wm8940.c static int wm8940_set_bias_level(struct · line 510
Quoted 9 lines
sound/soc/codecs/wm8940.c +0
-1@@ -496,7 +505,6 @@ static int wm8940_set_bias_level(struct snd_soc_component *component, return ret; } } -/* ensure bufioen and biasen */ pwr_reg |= (1 <<2 ) | (1 <<3 );/* set vmid to 300k for standby */ Unrelated (and questionable) whitespace change.
Ok. I will remove it.
Thanks for the review.
Best regards,
Lukasz Majewski
--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: [email protected]
PATCH 3/4 ASoC: wm8940: Mute also the speaker output
In reply to Lukasz MajewskiWithout this change the BTL speaker produces some "distortion" noise when test program (speaker-test -t waw) is ended with ctrl+c.
As our design uses speaker outputs to drive BTL speaker, it was necessary to also mute the speaker via the codec internal WM8940_SPKVOL register with setting WM8940_SPKMUTE bit.
--- sound/soc/codecs/wm8940.c | 11 ++++++++++- sound/soc/codecs/wm8940.h | 3 +++ 2 files changed, 13 insertions(+), 1 deletion(-)
sound/soc/codecs/wm8940.c +10 -1
@@ -465,9 +465,18 @@ static int wm8940_mute(struct snd_soc_dai *dai, int mute, int direction) {struct snd_soc_component *component = dai->component;u16 mute_reg =snd_soc_component_read (component,WM8940_DAC ) &0xffbf ; +u16 spkvol_reg =snd_soc_component_read (component,WM8940_SPKVOL ); +int ret; -if (mute) + spkvol_reg &= ~WM8940_SPKMUTE ; +if (mute) { mute_reg |=0x40 ; + spkvol_reg |=WM8940_SPKMUTE ; + } + + ret =snd_soc_component_write (component,WM8940_SPKVOL , spkvol_reg); +if (ret) +return ret;return snd_soc_component_write (component,WM8940_DAC , mute_reg); }
sound/soc/codecs/wm8940.h +3 -0
@@ -95,5 +95,8 @@ struct wm8940_setup_data {#define WM8940_OPCLKDIV_3 2#define WM8940_OPCLKDIV_4 3 +/* Bit definitions */ +#define WM8940_SPKMUTE BIT(6) +#endif /* _WM8940_H */
Signature · 1 line
2.20.1
Re: [PATCH 3/4] ASoC: wm8940: Mute also the speaker output
Quoted 11 lines · Lukasz Majewski
Without this change the BTL speaker produces some "distortion" noise when test program (speaker-test -t waw) is ended with ctrl+c.
As our design uses speaker outputs to drive BTL speaker, it was necessary to also mute the speaker via the codec internal
WM8940_SPKVOLregister with settingWM8940_SPKMUTEbit.Signed-off-by Lukasz Majewski <[email protected]>---
sound/soc/codecs/wm8940.c static int wm8940_mute(struct snd_soc_dai *dai, int mute, int direction) · line 479
Quoted 9 lines
sound/soc/codecs/wm8940.c +8
-0+ spkvol_reg &= ~WM8940_SPKMUTE ; +if (mute) { mute_reg |=0x40 ; + spkvol_reg |=WM8940_SPKMUTE ; + } + + ret =snd_soc_component_write (component,WM8940_SPKVOL , spkvol_reg); +if (ret) +return ret;
This bit is also controlled by the "Speaker Playback Switch" so you probably need some locking between them to stop them clobbering each other.
Thanks,
Charles
Mark Brown
maintainerRe: [PATCH 3/4] ASoC: wm8940: Mute also the speaker output
In reply to Lukasz MajewskiQuoted 13 lines · Lukasz Majewski
Without this change the BTL speaker produces some "distortion" noise when test program (speaker-test -t waw) is ended with ctrl+c.
As our design uses speaker outputs to drive BTL speaker, it was necessary to also mute the speaker via the codec internal
WM8940_SPKVOLregister with settingWM8940_SPKMUTEbit.sound/soc/codecs/wm8940.c +1
-0@@ -465,9 +465,18 @@ static int wm8940_mute(struct snd_soc_dai *dai, int mute, int direction) { + spkvol_reg &= ~WM8940_SPKMUTE ;
sound/soc/codecs/wm8940.c static int wm8940_mute(struct snd_soc_dai *dai, int mute, int direction) · line 477
Quoted 10 lines
sound/soc/codecs/wm8940.c +7
-0+if (mute) { mute_reg |=0x40 ; + spkvol_reg |=WM8940_SPKMUTE ; + } + + ret =snd_soc_component_write (component,WM8940_SPKVOL , spkvol_reg); +if (ret) +return ret;return snd_soc_component_write (component,WM8940_DAC , mute_reg);
In addition to the issue Charles raised this is simply not what the mute callback should do, the mute callback should specifically mute the digital input (with the goal of masking any glitching on there while clocks are started/stopped). Looking at the driver the device supports analogue bypass paths to the speaker - these will be broken by your patch so if you genuinely need some workaround in this area I'd be looking at the Speaker Mixer PCM Playback Switch rather than muting the speaker as a whole. If the device just can't cope without an input then ignore_mdown_time might be what you're looking for, it looks like the device doesn't have any lengthy sleeps in the power up/down paths so that should be fine so long as it doesn't pop/click.
I'd also check there's not some other system configuration issue here which is more obvious when the input from the DAC stops getting input, check that you don't see similar issues when silence is played for example. It might be worth checking that none of the analogue bypass paths are enabled.
Re: [PATCH 3/4] ASoC: wm8940: Mute also the speaker output
Hi Mark,
Quoted 24 lines · Lukasz Majewski
Quoted 23 lines
Without this change the BTL speaker produces some "distortion" noise when test program (speaker-test -t waw) is ended with ctrl+c.
As our design uses speaker outputs to drive BTL speaker, it was necessary to also mute the speaker via the codec internal
WM8940_SPKVOLregister with settingWM8940_SPKMUTEbit.sound/soc/codecs/wm8940.c +8
-0@@ -465,9 +465,18 @@ static int wm8940_mute(struct snd_soc_dai *dai, int mute, int direction) { + spkvol_reg &= ~WM8940_SPKMUTE ; +if (mute) { mute_reg |=0x40 ; + spkvol_reg |=WM8940_SPKMUTE ; + } + + ret =snd_soc_component_write (component,WM8940_SPKVOL , spkvol_reg); +if (ret) +return ret;
Quoted 7 lines
Review static int wm8940_mute(struct snd_soc_dai · line 479
Quoted 2 lines
(quoted diff) +0
-0return snd_soc_component_write(component, WM8940_DAC, mute_reg);In addition to the issue Charles raised this is simply not what the mute callback should do, the mute callback should specifically mute the digital input (with the goal of masking any glitching on there while clocks are started/stopped).
Ok
Quoted 3 lines
Looking at the driver the device
supports analogue bypass paths to the speaker - these will be broken by your patch
I was not aware about this side effect. I just wanted to be sure that the speaker is muted.
Quoted 3 lines
so if you genuinely need some workaround in this area I'd be looking at the Speaker Mixer PCM Playback Switch rather than muting the speaker as a whole.
I would be more than happy if I could use for example the 'amixer' command to setup the audio correctly without this patch.
For example - on this system - before I run any speaker test I need to
call: amixer -d set 'Speaker Mixer PCM',0 on
to unmute the system.
Quoted 5 lines
If the device just can't cope without
an input thenignore_mdown_timemight be what you're looking for, it looks like the device doesn't have any lengthy sleeps in the power up/down paths so that should be fine so long as it doesn't pop/click.
Ok. I will check this as well.
Quoted 5 lines
I'd also check there's not some other system configuration issue here which is more obvious when the input from the DAC stops getting input, check that you don't see similar issues when silence is played for example. It might be worth checking that none of the analogue bypass paths are enabled.
Thanks for your hints. I will investigate it further.
It looks like this patch is some kind of a hack, to fix my system configuration and shall be dropped in v2.
Best regards,
Lukasz Majewski
--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: [email protected]
Re: [PATCH 3/4] ASoC: wm8940: Mute also the speaker output
Hi Mark,
Quoted 47 lines
Hi Mark,
Quoted 24 lines · Lukasz Majewski
Quoted 23 lines
Without this change the BTL speaker produces some "distortion" noise when test program (speaker-test -t waw) is ended with ctrl+c.
As our design uses speaker outputs to drive BTL speaker, it was necessary to also mute the speaker via the codec internal
WM8940_SPKVOLregister with settingWM8940_SPKMUTEbit.sound/soc/codecs/wm8940.c +8
-0@@ -465,9 +465,18 @@ static int wm8940_mute(struct snd_soc_dai *dai, int mute, int direction) { + spkvol_reg &= ~WM8940_SPKMUTE ; +if (mute) { mute_reg |=0x40 ; + spkvol_reg |=WM8940_SPKMUTE ; + } + + ret =snd_soc_component_write (component,WM8940_SPKVOL , spkvol_reg); +if (ret) +return ret;Quoted 7 lines
Review static int wm8940_mute(struct snd_soc_dai · line 479
Quoted 2 lines
(quoted diff) +0
-0return snd_soc_component_write(component, WM8940_DAC, mute_reg);In addition to the issue Charles raised this is simply not what the mute callback should do, the mute callback should specifically mute the digital input (with the goal of masking any glitching on there while clocks are started/stopped).
Ok
Quoted 3 lines
Looking at the driver the device
supports analogue bypass paths to the speaker - these will be broken by your patchI was not aware about this side effect. I just wanted to be sure that the speaker is muted.
Quoted 3 lines
so if you genuinely need some workaround in this area I'd be looking at the Speaker Mixer PCM Playback Switch rather than muting the speaker as a whole.
Quoted 8 lines
I would be more than happy if I could use for example the 'amixer' command to setup the audio correctly without this patch.
For example - on this system - before I run any speaker test I need to
call: amixer -d set 'Speaker Mixer PCM',0 onto unmute the system.
This patch steamed from 4.4 Linux. On the newer Linux version the "distortion" problem is not present anymore.
I will drop this patch.
Quoted 22 lines
Quoted 5 lines
If the device just can't cope without
an input thenignore_mdown_timemight be what you're looking for, it looks like the device doesn't have any lengthy sleeps in the power up/down paths so that should be fine so long as it doesn't pop/click.Ok. I will check this as well.
Quoted 5 lines
I'd also check there's not some other system configuration issue here which is more obvious when the input from the DAC stops getting input, check that you don't see similar issues when silence is played for example. It might be worth checking that none of the analogue bypass paths are enabled.
Thanks for your hints. I will investigate it further.
It looks like this patch is some kind of a hack, to fix my system configuration and shall be dropped in v2.
Best regards,
Quoted 8 lines
Lukasz Majewski
--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email:
[email protected]
Best regards,
Lukasz Majewski
--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: [email protected]
PATCH 4/4 ASoC: wm8940: Read chip ID when wm8940 codec probing
In reply to Lukasz MajewskiThe wm8940 provides the chip ID information via I2C. In this patch this information is read and if not matching expected value, the probe function is aborted.
This prevents from using (i.e. inserting) other wm89* modules which use the sam I2C bus address.
--- sound/soc/codecs/wm8940.c | 11 +++++++++++ sound/soc/codecs/wm8940.h | 3 +++ 2 files changed, 14 insertions(+)
sound/soc/codecs/wm8940.c +11 -0
@@ -769,6 +769,17 @@ static int wm8940_probe(struct snd_soc_component *component)int ret;u16 reg; +/* +* Check chip ID for wm8940 - value of 0x00 offset +* SOFTWARE_RESET on write +* CHIP_ID on read +*/ + reg =snd_soc_component_read (component,WM8940_SOFTRESET ); +if (reg !=WM8940_CHIP_ID ) { +dev_err (component->dev,"Wrong wm8940 chip ID: 0x%x\n" , reg); +return -ENODEV ; + } + ret =wm8940_reset (component);if (ret <0 ) {dev_err (component->dev,"Failed to issue reset\n" );
sound/soc/codecs/wm8940.h +3 -0
@@ -98,5 +98,8 @@ struct wm8940_setup_data {/* Bit definitions */ #define WM8940_SPKMUTE BIT(6) +/* Chip ID */ +#define WM8940_CHIP_ID 0x8940 +#endif /* _WM8940_H */
Signature · 1 line
2.20.1
Re: [PATCH 4/4] ASoC: wm8940: Read chip ID when wm8940 codec probing
Quoted 9 lines · Lukasz Majewski
The wm8940 provides the chip ID information via I2C. In this patch this information is read and if not matching expected value, the probe function is aborted.
This prevents from using (i.e. inserting) other wm89* modules which use the sam I2C bus address.
Signed-off-by Lukasz Majewski <[email protected]>---
Thanks,
Charles
PATCH v2 1/3 ASoC: wm8940: Remove warning when no plat data present
In reply to Lukasz MajewskiThe lack of platform data in the contemporary Linux shall not be the reason to display warnings to the kernel logs.
---
Changes for v2:
- None
--- sound/soc/codecs/wm8940.c | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-)
sound/soc/codecs/wm8940.c +1 -3
@@ -709,9 +709,7 @@ static int wm8940_probe(struct snd_soc_component *component)if (ret <0 )return ret; -if (!pdata) -dev_warn (component->dev,"No platform data supplied\n" ); -else { +if (pdata) { reg =snd_soc_component_read (component,WM8940_OUTPUTCTL ); ret =snd_soc_component_write (component,WM8940_OUTPUTCTL , reg | pdata->vroi);if (ret <0 )
Signature · 1 line
2.20.1
PATCH v2 2/3 ASoC: wm8940: Rewrite code to set proper clocks
This patch enables support for internal wm8940's PLL and proper divider to set proper value for 256x fs clock.
This approach is more flexible and replaces hardcoded clock values and makes the codec work with the simple-card driver. Card drivers calling set_pll() and set_clkdiv() directly are unaffected.
For the reference - code in this commit is based on:
"ASoC: wm8974: configure pll and mclk divider automatically" (SHA1: 51b2bb3f2568e6d9d81a001d38b8d70c2ba4af99).
---
Changes for v2:
- Remove not required line add/remove
- Rewrite the commit message to describe more precisely the problem
--- sound/soc/codecs/wm8940.c | 101 +++++++++++++++++++++++++++++++------- 1 file changed, 82 insertions(+), 19 deletions(-)
sound/soc/codecs/wm8940.c +82 -19
@@ -37,7 +37,9 @@#include "wm8940.h" struct wm8940_priv { -unsigned int sysclk; +unsigned int mclk; +unsigned int fs; +struct regmap *regmap; };
@@ -387,17 +389,24 @@ static int wm8940_set_dai_fmt(struct snd_soc_dai *codec_dai,return 0 ; } +static int wm8940_update_clocks (struct snd_soc_dai *dai);static int wm8940_i2s_hw_params (struct snd_pcm_substream *substream,struct snd_pcm_hw_params *params,struct snd_soc_dai *dai) {struct snd_soc_component *component = dai->component; +struct wm8940_priv *priv =snd_soc_component_get_drvdata (component);u16 iface =snd_soc_component_read (component,WM8940_IFACE ) &0xFD9F ;u16 addcntrl =snd_soc_component_read (component,WM8940_ADDCNTRL ) &0xFFF1 ;u16 companding =snd_soc_component_read (component,WM8940_COMPANDINGCTL ) &0xFFDF ;int ret; + priv->fs =params_rate (params); + ret =wm8940_update_clocks (dai); +if (ret) +return ret; +/* LoutR control */ if (substream->stream ==SNDRV_PCM_STREAM_CAPTURE &¶ms_channels (params) ==2 )
@@ -611,24 +620,6 @@ static int wm8940_set_dai_pll(struct snd_soc_dai *codec_dai, int pll_id,return 0 ; } -static int wm8940_set_dai_sysclk (struct snd_soc_dai *codec_dai, -int clk_id,unsigned int freq,int dir) -{ -struct snd_soc_component *component = codec_dai->component; -struct wm8940_priv *wm8940 =snd_soc_component_get_drvdata (component); - -switch (freq) { -case 11289600 : -case 12000000 : -case 12288000 : -case 16934400 : -case 18432000 : - wm8940->sysclk = freq; -return 0 ; - } -return -EINVAL ; -} -static int wm8940_set_dai_clkdiv (struct snd_soc_dai *codec_dai,int div_id,int div) {
@@ -653,6 +644,78 @@ static int wm8940_set_dai_clkdiv(struct snd_soc_dai *codec_dai,return ret; } +static unsigned int wm8940_get_mclkdiv (unsigned int f_in,unsigned int f_out, +int *mclkdiv) +{ +unsigned int ratio =2 * f_in / f_out; + +if (ratio <=2 ) { + *mclkdiv =WM8940_MCLKDIV_1 ; + ratio =2 ; + }else if (ratio ==3 ) { + *mclkdiv =WM8940_MCLKDIV_1_5 ; + }else if (ratio ==4 ) { + *mclkdiv =WM8940_MCLKDIV_2 ; + }else if (ratio <=6 ) { + *mclkdiv =WM8940_MCLKDIV_3 ; + ratio =6 ; + }else if (ratio <=8 ) { + *mclkdiv =WM8940_MCLKDIV_4 ; + ratio =8 ; + }else if (ratio <=12 ) { + *mclkdiv =WM8940_MCLKDIV_6 ; + ratio =12 ; + }else if (ratio <=16 ) { + *mclkdiv =WM8940_MCLKDIV_8 ; + ratio =16 ; + }else { + *mclkdiv =WM8940_MCLKDIV_12 ; + ratio =24 ; + } + +return f_out * ratio /2 ; +} + +static int wm8940_update_clocks (struct snd_soc_dai *dai) +{ +struct snd_soc_component *codec = dai->component; +struct wm8940_priv *priv =snd_soc_component_get_drvdata (codec); +unsigned int fs256; +unsigned int fpll =0 ; +unsigned int f; +int mclkdiv; + +if (!priv->mclk || !priv->fs) +return 0 ; + + fs256 =256 * priv->fs; + + f =wm8940_get_mclkdiv (priv->mclk, fs256, &mclkdiv); +if (f != priv->mclk) { +/* The PLL performs best around 90MHz */ + fpll =wm8940_get_mclkdiv (22500000 , fs256, &mclkdiv); + } + +wm8940_set_dai_pll (dai,0 ,0 , priv->mclk, fpll); +wm8940_set_dai_clkdiv (dai,WM8940_MCLKDIV , mclkdiv); + +return 0 ; +} + +static int wm8940_set_dai_sysclk (struct snd_soc_dai *dai,int clk_id, +unsigned int freq,int dir) +{ +struct snd_soc_component *codec = dai->component; +struct wm8940_priv *priv =snd_soc_component_get_drvdata (codec); + +if (dir !=SND_SOC_CLOCK_IN ) +return -EINVAL ; + + priv->mclk = freq; + +return wm8940_update_clocks (dai); +} +#define WM8940_RATES SNDRV_PCM_RATE_8000_48000#define WM8940_FORMATS (SNDRV_PCM_FMTBIT_S8 | \
Signature · 1 line
2.20.1
Re: [PATCH v2 2/3] ASoC: wm8940: Rewrite code to set proper clocks
Quoted 11 lines · Lukasz Majewski
This patch enables support for internal wm8940's PLL and proper divider to set proper value for 256x fs clock.
This approach is more flexible and replaces hardcoded clock values and makes the codec work with the simple-card driver. Card drivers calling
set_pll()andset_clkdiv()directly are unaffected.For the reference - code in this commit is based on:
"ASoC: wm8974: configure pll and mclk divider automatically" (SHA1:51b2bb3f2568e6d9d81a001d38b8d70c2ba4af99).
Minor nit this doesn't quite match the commit <12-chars of SHA> ("<description>") format in Submitting-patches.rst.
Quoted 3 lines
Signed-off-by Lukasz Majewski <[email protected]>---
But the patch looks good to me:
Thanks,
Charles
PATCH v2 3/3 ASoC: wm8940: Read chip ID when wm8940 codec probing
In reply to Lukasz MajewskiThe wm8940 provides the chip ID information via I2C. In this patch this information is read and if not matching expected value, the probe function is aborted.
This prevents from using (i.e. inserting) other wm89* modules which use the same I2C bus address.
---
Changes for v2:
- None
--- sound/soc/codecs/wm8940.c | 11 +++++++++++ sound/soc/codecs/wm8940.h | 3 +++ 2 files changed, 14 insertions(+)
sound/soc/codecs/wm8940.c +11 -0
@@ -760,6 +760,17 @@ static int wm8940_probe(struct snd_soc_component *component)int ret;u16 reg; +/* +* Check chip ID for wm8940 - value of 0x00 offset +* SOFTWARE_RESET on write +* CHIP_ID on read +*/ + reg =snd_soc_component_read (component,WM8940_SOFTRESET ); +if (reg !=WM8940_CHIP_ID ) { +dev_err (component->dev,"Wrong wm8940 chip ID: 0x%x\n" , reg); +return -ENODEV ; + } + ret =wm8940_reset (component);if (ret <0 ) {dev_err (component->dev,"Failed to issue reset\n" );
sound/soc/codecs/wm8940.h +3 -0
@@ -95,5 +95,8 @@ struct wm8940_setup_data {#define WM8940_OPCLKDIV_3 2#define WM8940_OPCLKDIV_4 3 +/* Chip ID */ +#define WM8940_CHIP_ID 0x8940 +#endif /* _WM8940_H */
Signature · 1 line
2.20.1
Mark Brown
maintainerRe: [PATCH v2 1/3] ASoC: wm8940: Remove warning when no plat data present
In reply to Lukasz MajewskiQuoted 3 lines · Lukasz Majewski
The lack of platform data in the contemporary Linux shall not be the reason to display warnings to the kernel logs.
Please don't send new patches in reply to old patches or serieses, this makes it harder for both people and tools to understand what is going on - it can bury things in mailboxes and make it difficult to keep track of what current patches are, both for the new patches and the old ones.
Re: [PATCH v2 1/3] ASoC: wm8940: Remove warning when no plat data present
Hi Mark,
Quoted 10 lines · Lukasz Majewski
Quoted 3 lines
The lack of platform data in the contemporary Linux shall not be the reason to display warnings to the kernel logs.
Please don't send new patches in reply to old patches or serieses, this makes it harder for both people and tools to understand what is going on - it can bury things in mailboxes and make it difficult to keep track of what current patches are, both for the new patches and the old ones.
Ok. I will not use --in-reply-to.
Best regards,
Lukasz Majewski
--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: [email protected]
Mark Brown
maintainerRe: (subset) [PATCH 0/4] ASoC: Fixes for WM8940 codec
In reply to Lukasz MajewskiQuoted 6 lines · Lukasz Majewski
This patch series provides fixes for WM8940 codec.
The most notable change is the clock rewrite, so this driver now can either generate proper clock frequency by itself or use one provided from the clock subsystem of the SoC.
Quoted 7 lines
Lukasz Majewski (4):
ASoC: wm8940: Remove warning when no plat data present
ASoC: wm8940: Rewrite code to set proper clocks
ASoC: wm8940: Mute also the speaker output
ASoC: wm8940: Read chip ID when wm8940 codec probing[...]
Applied to
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git for-next
Thanks!
[1/4] ASoC: wm8940: Remove warning when no plat data present
commit: 5dc5e76b4c41fc8cdd9ed77653b2ce453974fb30
[4/4] ASoC: wm8940: Read chip ID when wm8940 codec probing
commit: a5c26ee572d94337baf9c944b7b4881a2db62d37All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent to Linus during the next merge window (or sooner if it is a bug fix), however if problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying to this mail.
Thanks,
Mark
Mark Brown
maintainerQuoted 6 lines · Lukasz Majewski
This patch series provides fixes for WM8940 codec.
The most notable change is the clock rewrite, so this driver now can either generate proper clock frequency by itself or use one provided from the clock subsystem of the SoC.
Quoted 7 lines
Lukasz Majewski (4):
ASoC: wm8940: Remove warning when no plat data present
ASoC: wm8940: Rewrite code to set proper clocks
ASoC: wm8940: Mute also the speaker output
ASoC: wm8940: Read chip ID when wm8940 codec probing[...]
Applied to
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git for-next
Thanks!
[1/3] ASoC: wm8940: Remove warning when no plat data present
commit: 5dc5e76b4c41fc8cdd9ed77653b2ce453974fb30
[2/3] ASoC: wm8940: Rewrite code to set proper clocks
commit: 294833fc9eb4e9d6c69f8d158cd991d641e59908
[3/3] ASoC: wm8940: Read chip ID when wm8940 codec probing
commit: a5c26ee572d94337baf9c944b7b4881a2db62d37All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent to Linus during the next merge window (or sooner if it is a bug fix), however if problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying to this mail.
Thanks,
Mark