docs: usbip: Fix major fields and descriptions in protocol
Subsystems (3)
Hongren Zheng (Zenithal)
reviewerPATCH 1/1 docs: usbip: Fix major fields and descriptions in protocol
The old document for usbip protocol is misleading and hard to read:
* Some fields in header are incorrect
* Explanation of some fields are unclear or even wrong
* Padding of header (namely all headers have the same length) is not explicitly point out, which is crucial for stream protocol like TCP
These fixes are made through reading usbip kernel drivers and userland codes. Also I have implemented one usbip server.
Major changes:
* Document the correct field as described in the codebase.
* Document the padding in usbip headers. This is crucial for TCP stream hence these padding should be explicitly point out. In code these padding are implemented by a union of all headers.
* Fix two FIXME related to usbip unlink and Document the behavior of unlink in different situation.
* Clarify some field with more accurate explanation, like those fields associated with URB. Some constraints are extracted from code.
* Delete specific transfer_flag doc in usbip as it should be documented by the URB part.
* Add data captured from wire as example
--- Documentation/usb/usbip_protocol.rst | 284 +++++++++++++++------------ 1 file changed, 156 insertions(+), 128 deletions(-)
Documentation/usb/usbip_protocol.rst +156 -128
@@ -5,8 +5,14 @@ USB/IP protocol PRELIMINARY DRAFT, MAY CONTAIN MISTAKES! 28 Jun 2011 +Update: Fix major fields in protocol +14 Mar 2021 + +Architecture +============ + The USB/IP protocol follows a server/client architecture. The server exports the -USB devices and the clients imports them. The device driver for the exported +USB devices and the client imports them. The device driver for the exported USB device runs on the client machine. The client may ask for the list of the exported USB devices. To get the list the
@@ -37,6 +43,9 @@ to transfer the URB traffic between the client and the server. The client may send two types of packets: the USBIP_CMD_SUBMIT to submit an URB, and USBIP_CMD_UNLINK to unlink a previously submitted URB. The answers of the server may be USBIP_RET_SUBMIT and USBIP_RET_UNLINK respectively. +Note that after successful USBIP_RET_UNLINK, the unlinked URB request would not +have a corresponding USBIP_RET_UNLINK (this is explained in +drivers/usb/usbip/stub_rx.c). ::
@@ -85,16 +94,42 @@ server may be USBIP_RET_SUBMIT and USBIP_RET_UNLINK respectively. | . | | : | | | + | USBIP_CMD_SUBMIT(seqnum = p) | + | ----------------------------------------------> | + | | | USBIP_CMD_UNLINK | + | (seqnum = p+1, unlink_seqnum = p) | | ----------------------------------------------> | | | | USBIP_RET_UNLINK | + | (seqnum = p+1, status = -ECONNRESET) | + | <---------------------------------------------- | + | | + | Note: No USBIP_RET_SUBMIT(seqnum = p) | + | <--X---X---X---X---X---X---X---X---X---X---X--- | + | . | + | : | + | | + | USBIP_CMD_SUBMIT(seqnum = q) | + | ----------------------------------------------> | + | | + | USBIP_RET_SUBMIT(seqnum = q) | + | <---------------------------------------------- | + | | + | USBIP_CMD_UNLINK | + | (seqnum = q+1, unlink_seqnum = q) | + | ----------------------------------------------> | + | | + | USBIP_RET_UNLINK | + | (seqnum = q+1, status = 0) | | <---------------------------------------------- | | | The fields are in network (big endian) byte order meaning that the most significant byte (MSB) is stored at the lowest address. +Message Format +============== OP_REQ_DEVLIST: Retrieve the list of exported USB devices.
@@ -102,7 +137,7 @@ OP_REQ_DEVLIST: +-----------+--------+------------+---------------------------------------------------+ | Offset | Length | Value | Description | +===========+========+============+===================================================+ -| 0 | 2 | 0x0100 | Binary-coded decimal USBIP version number: v1.0.0 | +| 0 | 2 | 0x0111 | Binary-coded decimal USBIP version number: v1.1.1 | +-----------+--------+------------+---------------------------------------------------+ | 2 | 2 | 0x8005 | Command code: Retrieve the list of exported USB | | | | | devices. |
@@ -116,7 +151,7 @@ OP_REP_DEVLIST: +-----------+--------+------------+---------------------------------------------------+ | Offset | Length | Value | Description | +===========+========+============+===================================================+ -| 0 | 2 | 0x0100 | Binary-coded decimal USBIP version number: v1.0.0.| +| 0 | 2 | 0x0111 | Binary-coded decimal USBIP version number: v1.1.1 | +-----------+--------+------------+---------------------------------------------------+ | 2 | 2 | 0x0005 | Reply code: The list of exported USB devices. | +-----------+--------+------------+---------------------------------------------------+
@@ -187,7 +222,7 @@ OP_REQ_IMPORT: +-----------+--------+------------+---------------------------------------------------+ | Offset | Length | Value | Description | +===========+========+============+===================================================+ -| 0 | 2 | 0x0100 | Binary-coded decimal USBIP version number: v1.0.0 | +| 0 | 2 | 0x0111 | Binary-coded decimal USBIP version number: v1.1.1 | +-----------+--------+------------+---------------------------------------------------+ | 2 | 2 | 0x8003 | Command code: import a remote USB device. | +-----------+--------+------------+---------------------------------------------------+
@@ -206,7 +241,7 @@ OP_REP_IMPORT: +-----------+--------+------------+---------------------------------------------------+ | Offset | Length | Value | Description | +===========+========+============+===================================================+ -| 0 | 2 | 0x0100 | Binary-coded decimal USBIP version number: v1.0.0 | +| 0 | 2 | 0x0111 | Binary-coded decimal USBIP version number: v1.1.1 | +-----------+--------+------------+---------------------------------------------------+ | 2 | 2 | 0x0003 | Reply code: Reply to import. | +-----------+--------+------------+---------------------------------------------------+
@@ -254,65 +289,75 @@ OP_REP_IMPORT: | 0x13E | 1 | | bNumInterfaces | +-----------+--------+------------+---------------------------------------------------+ -USBIP_CMD_SUBMIT: - Submit an URB +The following four commands have a common basic header called +'usbip_header_basic', and their headers, called 'usbip_header' (before URB +payload), have the same length, therefore paddings are needed. -+-----------+--------+------------+---------------------------------------------------+ -| Offset | Length | Value | Description | -+===========+========+============+===================================================+ -| 0 | 4 | 0x00000001 | command: Submit an URB | -+-----------+--------+------------+---------------------------------------------------+ -| 4 | 4 | | seqnum: the sequence number of the URB to submit | -+-----------+--------+------------+---------------------------------------------------+ -| 8 | 4 | | devid | -+-----------+--------+------------+---------------------------------------------------+ -| 0xC | 4 | | direction: | -| | | | | -| | | | - 0: USBIP_DIR_OUT | -| | | | - 1: USBIP_DIR_IN | -+-----------+--------+------------+---------------------------------------------------+ -| 0x10 | 4 | | ep: endpoint number, possible values are: 0...15 | -+-----------+--------+------------+---------------------------------------------------+ -| 0x14 | 4 | | transfer_flags: possible values depend on the | -| | | | URB transfer type, see below | -+-----------+--------+------------+---------------------------------------------------+ -| 0x18 | 4 | | transfer_buffer_length | -+-----------+--------+------------+---------------------------------------------------+ -| 0x1C | 4 | | start_frame: specify the selected frame to | -| | | | transmit an ISO frame, ignored if URB_ISO_ASAP | -| | | | is specified at transfer_flags | -+-----------+--------+------------+---------------------------------------------------+ -| 0x20 | 4 | | number_of_packets: number of ISO packets | -+-----------+--------+------------+---------------------------------------------------+ -| 0x24 | 4 | | interval: maximum time for the request on the | -| | | | server-side host controller | -+-----------+--------+------------+---------------------------------------------------+ -| 0x28 | 8 | | setup: data bytes for USB setup, filled with | -| | | | zeros if not used | -+-----------+--------+------------+---------------------------------------------------+ -| 0x30 | | | URB data. For ISO transfers the padding between | -| | | | each ISO packets is not transmitted. | -+-----------+--------+------------+---------------------------------------------------+ +usbip_header_basic: ++-----------+--------+---------------------------------------------------+ +| Offset | Length | Description | ++===========+========+===================================================+ +| 0 | 4 | command | ++-----------+--------+---------------------------------------------------+ +| 4 | 4 | seqnum: sequential number that identifies requests| +| | | and corresponding responses; | +| | | incremented per connection | ++-----------+--------+---------------------------------------------------+ +| 8 | 4 | devid: specifies a remote USB device uniquely | +| | | instead of busnum and devnum; | +| | | for client (request), this value is | +| | | ((busnum << 16) | devnum); | +| | | for server (response), this shall be set to 0 | ++-----------+--------+---------------------------------------------------+ +| 0xC | 4 | direction: | +| | | | +| | | - 0: USBIP_DIR_OUT | +| | | - 1: USBIP_DIR_IN | +| | | | +| | | only used by client, for server this shall be 0 | ++-----------+--------+---------------------------------------------------+ +| 0x10 | 4 | ep: endpoint number | +| | | only used by client, for server this shall be 0 | +| | | for UNLINK, this shall be 0 | ++-----------+--------+---------------------------------------------------+ - +-------------------------+------------+---------+-----------+----------+-------------+ - | Allowed transfer_flags | value | control | interrupt | bulk | isochronous | - +=========================+============+=========+===========+==========+=============+ - | URB_SHORT_NOT_OK | 0x00000001 | only in | only in | only in | no | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_ISO_ASAP | 0x00000002 | no | no | no | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_NO_TRANSFER_DMA_MAP | 0x00000004 | yes | yes | yes | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_ZERO_PACKET | 0x00000040 | no | no | only out | no | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_NO_INTERRUPT | 0x00000080 | yes | yes | yes | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_FREE_BUFFER | 0x00000100 | yes | yes | yes | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_DIR_MASK | 0x00000200 | yes | yes | yes | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ +USBIP_CMD_SUBMIT: + Submit an URB ++-----------+--------+---------------------------------------------------+ +| Offset | Length | Description | ++===========+========+===================================================+ +| 0 | 20 | usbip_header_basic, 'command' shall be 0x00000001 | ++-----------+--------+---------------------------------------------------+ +| 0x14 | 4 | transfer_flags: possible values depend on the | +| | | URB transfer_flags, | +| | | but with URB_NO_TRANSFER_DMA_MAP masked | ++-----------+--------+---------------------------------------------------+ +| 0x18 | 4 | transfer_buffer_length: | +| | | use URB transfer_buffer_length | ++-----------+--------+---------------------------------------------------+ +| 0x1C | 4 | start_frame: use URB start_frame; | +| | | initial frame for ISO transfer | +| | | shall be set to 0 if not ISO transfer | ++-----------+--------+---------------------------------------------------+ +| 0x20 | 4 | number_of_packets: number of ISO packets | +| | | shall be set to 0xffffffff if not ISO transfer | ++-----------+--------+---------------------------------------------------+ +| 0x24 | 4 | interval: maximum time for the request on the | +| | | server-side host controller | ++-----------+--------+---------------------------------------------------+ +| 0x28 | 8 | setup: data bytes for USB setup, filled with | +| | | zeros if not used | ++-----------+--------+---------------------------------------------------+ +| 0x30 | n | tranfer_buffer. | +| | | If direction is USBIP_DIR_OUT then n equals | +| | | transfer_buffer_length; otherwise n equals 0 | +| | | For ISO transfers the padding between each ISO | +| | | between each ISO packets is not transmitted. | ++-----------+--------+---------------------------------------------------+ +| 0x30+n | m | iso_packet_descriptor | ++-----------+--------+---------------------------------------------------+ USBIP_RET_SUBMIT: Reply for submitting an URB
@@ -320,92 +365,75 @@ USBIP_RET_SUBMIT: +-----------+--------+------------+---------------------------------------------------+ | Offset | Length | Value | Description | +===========+========+============+===================================================+ -| 0 | 4 | 0x00000003 | command | -+-----------+--------+------------+---------------------------------------------------+ -| 4 | 4 | | seqnum: URB sequence number | -+-----------+--------+------------+---------------------------------------------------+ -| 8 | 4 | | devid | -+-----------+--------+------------+---------------------------------------------------+ -| 0xC | 4 | | direction: | -| | | | | -| | | | - 0: USBIP_DIR_OUT | -| | | | - 1: USBIP_DIR_IN | -+-----------+--------+------------+---------------------------------------------------+ -| 0x10 | 4 | | ep: endpoint number | +| 0 | 20 | | usbip_header_basic, 'command' shall be 0x00000003 | +-----------+--------+------------+---------------------------------------------------+ | 0x14 | 4 | | status: zero for successful URB transaction, | | | | | otherwise some kind of error happened. | +-----------+--------+------------+---------------------------------------------------+ | 0x18 | 4 | n | actual_length: number of URB data bytes | +| | | | use URB actual_length | +-----------+--------+------------+---------------------------------------------------+ -| 0x1C | 4 | | start_frame: for an ISO frame the actually | -| | | | selected frame for transmit. | +| 0x1C | 4 | | start_frame: use URB start_frame; | +| | | | initial frame for ISO transfer | +| | | | shall be set to 0 if not ISO transfer | +-----------+--------+------------+---------------------------------------------------+ -| 0x20 | 4 | | number_of_packets | +| 0x20 | 4 | | number_of_packets: number of ISO packets | +| | | | shall be set to 0xffffffff if not ISO transfer | +-----------+--------+------------+---------------------------------------------------+ | 0x24 | 4 | | error_count | +-----------+--------+------------+---------------------------------------------------+ -| 0x28 | 8 | | setup: data bytes for USB setup, filled with | -| | | | zeros if not used | +| 0x28 | 8 | | padding, shall be set to 0 | +-----------+--------+------------+---------------------------------------------------+ -| 0x30 | n | | URB data bytes. For ISO transfers the padding | +| 0x30 | n | | tranfer_buffer. | +| | | | If direction is USBIP_DIR_OUT then n equals | +| | | | transfer_buffer_length; otherwise n equals 0 | +| | | | For ISO transfers the padding between each ISO | | | | | between each ISO packets is not transmitted. | +-----------+--------+------------+---------------------------------------------------+ +| 0x30+n | m | | iso_packet_descriptor | ++-----------+--------+------------+---------------------------------------------------+ USBIP_CMD_UNLINK: Unlink an URB -+-----------+--------+------------+---------------------------------------------------+ -| Offset | Length | Value | Description | -+===========+========+============+===================================================+ -| 0 | 4 | 0x00000002 | command: URB unlink command | -+-----------+--------+------------+---------------------------------------------------+ -| 4 | 4 | | seqnum: URB sequence number to unlink: | -| | | | | -| | | | FIXME: | -| | | | is this so? | -+-----------+--------+------------+---------------------------------------------------+ -| 8 | 4 | | devid | -+-----------+--------+------------+---------------------------------------------------+ -| 0xC | 4 | | direction: | -| | | | | -| | | | - 0: USBIP_DIR_OUT | -| | | | - 1: USBIP_DIR_IN | -+-----------+--------+------------+---------------------------------------------------+ -| 0x10 | 4 | | ep: endpoint number: zero | -+-----------+--------+------------+---------------------------------------------------+ -| 0x14 | 4 | | seqnum: the URB sequence number given previously | -| | | | at USBIP_CMD_SUBMIT.seqnum field | -+-----------+--------+------------+---------------------------------------------------+ -| 0x30 | n | | URB data bytes. For ISO transfers the padding | -| | | | between each ISO packets is not transmitted. | -+-----------+--------+------------+---------------------------------------------------+ ++-----------+--------+---------------------------------------------------+ +| Offset | Length | Description | ++===========+========+===================================================+ +| 0 | 20 | usbip_header_basic, 'command' shall be 0x00000002 | ++-----------+--------+---------------------------------------------------+ +| 0x14 | 4 | unlink_seqnum, of the SUBMIT request to unlink | ++-----------+--------+---------------------------------------------------+ +| 0x18 | 24 | padding, shall be set to 0 | ++-----------+--------+---------------------------------------------------+ USBIP_RET_UNLINK: Reply for URB unlink -+-----------+--------+------------+---------------------------------------------------+ -| Offset | Length | Value | Description | -+===========+========+============+===================================================+ -| 0 | 4 | 0x00000004 | command: reply for the URB unlink command | -+-----------+--------+------------+---------------------------------------------------+ -| 4 | 4 | | seqnum: the unlinked URB sequence number | -+-----------+--------+------------+---------------------------------------------------+ -| 8 | 4 | | devid | -+-----------+--------+------------+---------------------------------------------------+ -| 0xC | 4 | | direction: | -| | | | | -| | | | - 0: USBIP_DIR_OUT | -| | | | - 1: USBIP_DIR_IN | -+-----------+--------+------------+---------------------------------------------------+ -| 0x10 | 4 | | ep: endpoint number | -+-----------+--------+------------+---------------------------------------------------+ -| 0x14 | 4 | | status: This is the value contained in the | -| | | | urb->status in the URB completition handler. | -| | | | | -| | | | FIXME: | -| | | | a better explanation needed. | -+-----------+--------+------------+---------------------------------------------------+ -| 0x30 | n | | URB data bytes. For ISO transfers the padding | -| | | | between each ISO packets is not transmitted. | -+-----------+--------+------------+---------------------------------------------------+ ++-----------+--------+---------------------------------------------------+ +| Offset | Length | Description | ++===========+========+===================================================+ +| 0 | 20 | usbip_header_basic, 'command' shall be 0x00000004 | ++-----------+--------+---------------------------------------------------+ +| 0x14 | 4 | status: This is similar to that status of | +| | | USBIP_RET_SUBMIT (share the same memory offset) | +| | | When UNLINK is successful, status is -ECONNRESET; | +| | | when USBIP_CMD_UNLINK is after USBIP_RET_SUBMIT | +| | | status is 0 | ++-----------+--------+---------------------------------------------------+ +| 0x18 | 24 | padding, shall be set to 0 | ++-----------+--------+---------------------------------------------------+ + +EXAMPLE +======= + + The following data is captured from wire with Human Interface Devices (HID) + payload + +:: + + CmdIntrIN: 00000001 00000d05 0001000f 00000001 00000001 00000200 00000040 ffffffff 00000000 00000004 00000000 00000000 + CmdIntrOUT: 00000001 00000d06 0001000f 00000000 00000001 00000000 00000040 ffffffff 00000000 00000004 00000000 00000000 + ffffffff860008a784ce5ae212376300000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 + RetIntrOut: 00000003 00000d06 00000000 00000000 00000000 00000000 00000040 ffffffff 00000000 00000000 00000000 00000000 + RetIntrIn: 00000003 00000d05 00000000 00000000 00000000 00000000 00000040 ffffffff 00000000 00000000 00000000 00000000 + ffffffff860011a784ce5ae2123763612891b1020100000400000000000000000000000000000000000000000000000000000000000000000000000000000000
Signature · 5 lines
2.30.1 -- GPG Fingerprint: 1127F188280AE3123619332987E17EEF9B18B6C9
Hongren Zheng (Zenithal)
reviewerPATCH v2 1/1 docs: usbip: Fix major fields and descriptions in protocol
The old document for usbip protocol is misleading and hard to read:
* Some fields in header are incorrect
* Explanation of some fields are unclear or even wrong
* Padding of header (namely all headers have the same length) is not explicitly point out, which is crucial for stream protocol like TCP
These fixes are made through reading usbip kernel drivers and userland codes. Also I have implemented one usbip server.
Major changes:
* Document the correct field as described in the codebase.
* Document the padding in usbip headers. This is crucial for TCP stream hence these padding should be explicitly point out. In code these padding are implemented by a union of all headers.
* Fix two FIXME related to usbip unlink and Document the behavior of unlink in different situation.
* Clarify some field with more accurate explanation, like those fields associated with URB. Some constraints are extracted from code.
* Delete specific transfer_flag doc in usbip as it should be documented by the URB part.
* Add data captured from wire as example
Also some changes suggested by a previous patch in
https://lore.kernel.org/linux-usb/[email protected]/
is adopted in this patch.
--- Documentation/usb/usbip_protocol.rst | 290 +++++++++++++++------------ 1 file changed, 159 insertions(+), 131 deletions(-)
Documentation/usb/usbip_protocol.rst +159 -131
@@ -5,8 +5,14 @@ USB/IP protocol PRELIMINARY DRAFT, MAY CONTAIN MISTAKES! 28 Jun 2011 +Update: Fix major fields in protocol +14 Mar 2021 + +Architecture +============ + The USB/IP protocol follows a server/client architecture. The server exports the -USB devices and the clients imports them. The device driver for the exported +USB devices and the client imports them. The device driver for the exported USB device runs on the client machine. The client may ask for the list of the exported USB devices. To get the list the
@@ -37,6 +43,9 @@ to transfer the URB traffic between the client and the server. The client may send two types of packets: the USBIP_CMD_SUBMIT to submit an URB, and USBIP_CMD_UNLINK to unlink a previously submitted URB. The answers of the server may be USBIP_RET_SUBMIT and USBIP_RET_UNLINK respectively. +Note that after successful USBIP_RET_UNLINK, the unlinked URB request would not +have a corresponding USBIP_RET_UNLINK (this is explained in +drivers/usb/usbip/stub_rx.c). ::
@@ -85,16 +94,42 @@ server may be USBIP_RET_SUBMIT and USBIP_RET_UNLINK respectively. | . | | : | | | + | USBIP_CMD_SUBMIT(seqnum = p) | + | ----------------------------------------------> | + | | | USBIP_CMD_UNLINK | + | (seqnum = p+1, unlink_seqnum = p) | | ----------------------------------------------> | | | | USBIP_RET_UNLINK | + | (seqnum = p+1, status = -ECONNRESET) | + | <---------------------------------------------- | + | | + | Note: No USBIP_RET_SUBMIT(seqnum = p) | + | <--X---X---X---X---X---X---X---X---X---X---X--- | + | . | + | : | + | | + | USBIP_CMD_SUBMIT(seqnum = q) | + | ----------------------------------------------> | + | | + | USBIP_RET_SUBMIT(seqnum = q) | + | <---------------------------------------------- | + | | + | USBIP_CMD_UNLINK | + | (seqnum = q+1, unlink_seqnum = q) | + | ----------------------------------------------> | + | | + | USBIP_RET_UNLINK | + | (seqnum = q+1, status = 0) | | <---------------------------------------------- | | | The fields are in network (big endian) byte order meaning that the most significant byte (MSB) is stored at the lowest address. +Message Format +============== OP_REQ_DEVLIST: Retrieve the list of exported USB devices.
@@ -102,7 +137,7 @@ OP_REQ_DEVLIST: +-----------+--------+------------+---------------------------------------------------+ | Offset | Length | Value | Description | +===========+========+============+===================================================+ -| 0 | 2 | 0x0100 | Binary-coded decimal USBIP version number: v1.0.0 | +| 0 | 2 | 0x0111 | Binary-coded decimal USBIP version number: v1.1.1 | +-----------+--------+------------+---------------------------------------------------+ | 2 | 2 | 0x8005 | Command code: Retrieve the list of exported USB | | | | | devices. |
@@ -116,7 +151,7 @@ OP_REP_DEVLIST: +-----------+--------+------------+---------------------------------------------------+ | Offset | Length | Value | Description | +===========+========+============+===================================================+ -| 0 | 2 | 0x0100 | Binary-coded decimal USBIP version number: v1.0.0.| +| 0 | 2 | 0x0111 | Binary-coded decimal USBIP version number: v1.1.1 | +-----------+--------+------------+---------------------------------------------------+ | 2 | 2 | 0x0005 | Reply code: The list of exported USB devices. | +-----------+--------+------------+---------------------------------------------------+
@@ -165,8 +200,8 @@ OP_REP_DEVLIST: | 0x143 | 1 | | bNumInterfaces | +-----------+--------+------------+---------------------------------------------------+ | 0x144 | | m_0 | From now on each interface is described, all | -| | | | together bNumInterfaces times, with the | -| | | | the following 4 fields: | +| | | | together bNumInterfaces times, with the following | +| | | | 4 fields: | +-----------+--------+------------+---------------------------------------------------+ | | 1 | | bInterfaceClass | +-----------+--------+------------+---------------------------------------------------+
@@ -177,7 +212,7 @@ OP_REP_DEVLIST: | 0x147 | 1 | | padding byte for alignment, shall be set to zero | +-----------+--------+------------+---------------------------------------------------+ | 0xC + | | | The second exported USB device starts at i=1 | -| i*0x138 + | | | with the busid field. | +| i*0x138 + | | | with the path field. | | m_(i-1)*4 | | | | +-----------+--------+------------+---------------------------------------------------+
@@ -187,7 +222,7 @@ OP_REQ_IMPORT: +-----------+--------+------------+---------------------------------------------------+ | Offset | Length | Value | Description | +===========+========+============+===================================================+ -| 0 | 2 | 0x0100 | Binary-coded decimal USBIP version number: v1.0.0 | +| 0 | 2 | 0x0111 | Binary-coded decimal USBIP version number: v1.1.1 | +-----------+--------+------------+---------------------------------------------------+ | 2 | 2 | 0x8003 | Command code: import a remote USB device. | +-----------+--------+------------+---------------------------------------------------+
@@ -206,7 +241,7 @@ OP_REP_IMPORT: +-----------+--------+------------+---------------------------------------------------+ | Offset | Length | Value | Description | +===========+========+============+===================================================+ -| 0 | 2 | 0x0100 | Binary-coded decimal USBIP version number: v1.0.0 | +| 0 | 2 | 0x0111 | Binary-coded decimal USBIP version number: v1.1.1 | +-----------+--------+------------+---------------------------------------------------+ | 2 | 2 | 0x0003 | Reply code: Reply to import. | +-----------+--------+------------+---------------------------------------------------+
@@ -254,65 +289,75 @@ OP_REP_IMPORT: | 0x13E | 1 | | bNumInterfaces | +-----------+--------+------------+---------------------------------------------------+ -USBIP_CMD_SUBMIT: - Submit an URB +The following four commands have a common basic header called +'usbip_header_basic', and their headers, called 'usbip_header' (before URB +payload), have the same length, therefore paddings are needed. -+-----------+--------+------------+---------------------------------------------------+ -| Offset | Length | Value | Description | -+===========+========+============+===================================================+ -| 0 | 4 | 0x00000001 | command: Submit an URB | -+-----------+--------+------------+---------------------------------------------------+ -| 4 | 4 | | seqnum: the sequence number of the URB to submit | -+-----------+--------+------------+---------------------------------------------------+ -| 8 | 4 | | devid | -+-----------+--------+------------+---------------------------------------------------+ -| 0xC | 4 | | direction: | -| | | | | -| | | | - 0: USBIP_DIR_OUT | -| | | | - 1: USBIP_DIR_IN | -+-----------+--------+------------+---------------------------------------------------+ -| 0x10 | 4 | | ep: endpoint number, possible values are: 0...15 | -+-----------+--------+------------+---------------------------------------------------+ -| 0x14 | 4 | | transfer_flags: possible values depend on the | -| | | | URB transfer type, see below | -+-----------+--------+------------+---------------------------------------------------+ -| 0x18 | 4 | | transfer_buffer_length | -+-----------+--------+------------+---------------------------------------------------+ -| 0x1C | 4 | | start_frame: specify the selected frame to | -| | | | transmit an ISO frame, ignored if URB_ISO_ASAP | -| | | | is specified at transfer_flags | -+-----------+--------+------------+---------------------------------------------------+ -| 0x20 | 4 | | number_of_packets: number of ISO packets | -+-----------+--------+------------+---------------------------------------------------+ -| 0x24 | 4 | | interval: maximum time for the request on the | -| | | | server-side host controller | -+-----------+--------+------------+---------------------------------------------------+ -| 0x28 | 8 | | setup: data bytes for USB setup, filled with | -| | | | zeros if not used | -+-----------+--------+------------+---------------------------------------------------+ -| 0x30 | | | URB data. For ISO transfers the padding between | -| | | | each ISO packets is not transmitted. | -+-----------+--------+------------+---------------------------------------------------+ +usbip_header_basic: ++-----------+--------+---------------------------------------------------+ +| Offset | Length | Description | ++===========+========+===================================================+ +| 0 | 4 | command | ++-----------+--------+---------------------------------------------------+ +| 4 | 4 | seqnum: sequential number that identifies requests| +| | | and corresponding responses; | +| | | incremented per connection | ++-----------+--------+---------------------------------------------------+ +| 8 | 4 | devid: specifies a remote USB device uniquely | +| | | instead of busnum and devnum; | +| | | for client (request), this value is | +| | | ((busnum << 16) | devnum); | +| | | for server (response), this shall be set to 0 | ++-----------+--------+---------------------------------------------------+ +| 0xC | 4 | direction: | +| | | | +| | | - 0: USBIP_DIR_OUT | +| | | - 1: USBIP_DIR_IN | +| | | | +| | | only used by client, for server this shall be 0 | ++-----------+--------+---------------------------------------------------+ +| 0x10 | 4 | ep: endpoint number | +| | | only used by client, for server this shall be 0 | +| | | for UNLINK, this shall be 0 | ++-----------+--------+---------------------------------------------------+ - +-------------------------+------------+---------+-----------+----------+-------------+ - | Allowed transfer_flags | value | control | interrupt | bulk | isochronous | - +=========================+============+=========+===========+==========+=============+ - | URB_SHORT_NOT_OK | 0x00000001 | only in | only in | only in | no | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_ISO_ASAP | 0x00000002 | no | no | no | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_NO_TRANSFER_DMA_MAP | 0x00000004 | yes | yes | yes | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_ZERO_PACKET | 0x00000040 | no | no | only out | no | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_NO_INTERRUPT | 0x00000080 | yes | yes | yes | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_FREE_BUFFER | 0x00000100 | yes | yes | yes | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_DIR_MASK | 0x00000200 | yes | yes | yes | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ +USBIP_CMD_SUBMIT: + Submit an URB ++-----------+--------+---------------------------------------------------+ +| Offset | Length | Description | ++===========+========+===================================================+ +| 0 | 20 | usbip_header_basic, 'command' shall be 0x00000001 | ++-----------+--------+---------------------------------------------------+ +| 0x14 | 4 | transfer_flags: possible values depend on the | +| | | URB transfer_flags, | +| | | but with URB_NO_TRANSFER_DMA_MAP masked | ++-----------+--------+---------------------------------------------------+ +| 0x18 | 4 | transfer_buffer_length: | +| | | use URB transfer_buffer_length | ++-----------+--------+---------------------------------------------------+ +| 0x1C | 4 | start_frame: use URB start_frame; | +| | | initial frame for ISO transfer | +| | | shall be set to 0 if not ISO transfer | ++-----------+--------+---------------------------------------------------+ +| 0x20 | 4 | number_of_packets: number of ISO packets | +| | | shall be set to 0xffffffff if not ISO transfer | ++-----------+--------+---------------------------------------------------+ +| 0x24 | 4 | interval: maximum time for the request on the | +| | | server-side host controller | ++-----------+--------+---------------------------------------------------+ +| 0x28 | 8 | setup: data bytes for USB setup, filled with | +| | | zeros if not used | ++-----------+--------+---------------------------------------------------+ +| 0x30 | n | tranfer_buffer. | +| | | If direction is USBIP_DIR_OUT then n equals | +| | | transfer_buffer_length; otherwise n equals 0 | +| | | For ISO transfers the padding between each ISO | +| | | between each ISO packets is not transmitted. | ++-----------+--------+---------------------------------------------------+ +| 0x30+n | m | iso_packet_descriptor | ++-----------+--------+---------------------------------------------------+ USBIP_RET_SUBMIT: Reply for submitting an URB
@@ -320,92 +365,75 @@ USBIP_RET_SUBMIT: +-----------+--------+------------+---------------------------------------------------+ | Offset | Length | Value | Description | +===========+========+============+===================================================+ -| 0 | 4 | 0x00000003 | command | -+-----------+--------+------------+---------------------------------------------------+ -| 4 | 4 | | seqnum: URB sequence number | -+-----------+--------+------------+---------------------------------------------------+ -| 8 | 4 | | devid | -+-----------+--------+------------+---------------------------------------------------+ -| 0xC | 4 | | direction: | -| | | | | -| | | | - 0: USBIP_DIR_OUT | -| | | | - 1: USBIP_DIR_IN | -+-----------+--------+------------+---------------------------------------------------+ -| 0x10 | 4 | | ep: endpoint number | +| 0 | 20 | | usbip_header_basic, 'command' shall be 0x00000003 | +-----------+--------+------------+---------------------------------------------------+ | 0x14 | 4 | | status: zero for successful URB transaction, | | | | | otherwise some kind of error happened. | +-----------+--------+------------+---------------------------------------------------+ | 0x18 | 4 | n | actual_length: number of URB data bytes | +| | | | use URB actual_length | +-----------+--------+------------+---------------------------------------------------+ -| 0x1C | 4 | | start_frame: for an ISO frame the actually | -| | | | selected frame for transmit. | +| 0x1C | 4 | | start_frame: use URB start_frame; | +| | | | initial frame for ISO transfer | +| | | | shall be set to 0 if not ISO transfer | +-----------+--------+------------+---------------------------------------------------+ -| 0x20 | 4 | | number_of_packets | +| 0x20 | 4 | | number_of_packets: number of ISO packets | +| | | | shall be set to 0xffffffff if not ISO transfer | +-----------+--------+------------+---------------------------------------------------+ | 0x24 | 4 | | error_count | +-----------+--------+------------+---------------------------------------------------+ -| 0x28 | 8 | | setup: data bytes for USB setup, filled with | -| | | | zeros if not used | +| 0x28 | 8 | | padding, shall be set to 0 | +-----------+--------+------------+---------------------------------------------------+ -| 0x30 | n | | URB data bytes. For ISO transfers the padding | +| 0x30 | n | | tranfer_buffer. | +| | | | If direction is USBIP_DIR_OUT then n equals | +| | | | transfer_buffer_length; otherwise n equals 0 | +| | | | For ISO transfers the padding between each ISO | | | | | between each ISO packets is not transmitted. | +-----------+--------+------------+---------------------------------------------------+ +| 0x30+n | m | | iso_packet_descriptor | ++-----------+--------+------------+---------------------------------------------------+ USBIP_CMD_UNLINK: Unlink an URB -+-----------+--------+------------+---------------------------------------------------+ -| Offset | Length | Value | Description | -+===========+========+============+===================================================+ -| 0 | 4 | 0x00000002 | command: URB unlink command | -+-----------+--------+------------+---------------------------------------------------+ -| 4 | 4 | | seqnum: URB sequence number to unlink: | -| | | | | -| | | | FIXME: | -| | | | is this so? | -+-----------+--------+------------+---------------------------------------------------+ -| 8 | 4 | | devid | -+-----------+--------+------------+---------------------------------------------------+ -| 0xC | 4 | | direction: | -| | | | | -| | | | - 0: USBIP_DIR_OUT | -| | | | - 1: USBIP_DIR_IN | -+-----------+--------+------------+---------------------------------------------------+ -| 0x10 | 4 | | ep: endpoint number: zero | -+-----------+--------+------------+---------------------------------------------------+ -| 0x14 | 4 | | seqnum: the URB sequence number given previously | -| | | | at USBIP_CMD_SUBMIT.seqnum field | -+-----------+--------+------------+---------------------------------------------------+ -| 0x30 | n | | URB data bytes. For ISO transfers the padding | -| | | | between each ISO packets is not transmitted. | -+-----------+--------+------------+---------------------------------------------------+ ++-----------+--------+---------------------------------------------------+ +| Offset | Length | Description | ++===========+========+===================================================+ +| 0 | 20 | usbip_header_basic, 'command' shall be 0x00000002 | ++-----------+--------+---------------------------------------------------+ +| 0x14 | 4 | unlink_seqnum, of the SUBMIT request to unlink | ++-----------+--------+---------------------------------------------------+ +| 0x18 | 24 | padding, shall be set to 0 | ++-----------+--------+---------------------------------------------------+ USBIP_RET_UNLINK: Reply for URB unlink -+-----------+--------+------------+---------------------------------------------------+ -| Offset | Length | Value | Description | -+===========+========+============+===================================================+ -| 0 | 4 | 0x00000004 | command: reply for the URB unlink command | -+-----------+--------+------------+---------------------------------------------------+ -| 4 | 4 | | seqnum: the unlinked URB sequence number | -+-----------+--------+------------+---------------------------------------------------+ -| 8 | 4 | | devid | -+-----------+--------+------------+---------------------------------------------------+ -| 0xC | 4 | | direction: | -| | | | | -| | | | - 0: USBIP_DIR_OUT | -| | | | - 1: USBIP_DIR_IN | -+-----------+--------+------------+---------------------------------------------------+ -| 0x10 | 4 | | ep: endpoint number | -+-----------+--------+------------+---------------------------------------------------+ -| 0x14 | 4 | | status: This is the value contained in the | -| | | | urb->status in the URB completition handler. | -| | | | | -| | | | FIXME: | -| | | | a better explanation needed. | -+-----------+--------+------------+---------------------------------------------------+ -| 0x30 | n | | URB data bytes. For ISO transfers the padding | -| | | | between each ISO packets is not transmitted. | -+-----------+--------+------------+---------------------------------------------------+ ++-----------+--------+---------------------------------------------------+ +| Offset | Length | Description | ++===========+========+===================================================+ +| 0 | 20 | usbip_header_basic, 'command' shall be 0x00000004 | ++-----------+--------+---------------------------------------------------+ +| 0x14 | 4 | status: This is similar to that status of | +| | | USBIP_RET_SUBMIT (share the same memory offset) | +| | | When UNLINK is successful, status is -ECONNRESET; | +| | | when USBIP_CMD_UNLINK is after USBIP_RET_SUBMIT | +| | | status is 0 | ++-----------+--------+---------------------------------------------------+ +| 0x18 | 24 | padding, shall be set to 0 | ++-----------+--------+---------------------------------------------------+ + +EXAMPLE +======= + + The following data is captured from wire with Human Interface Devices (HID) + payload + +:: + + CmdIntrIN: 00000001 00000d05 0001000f 00000001 00000001 00000200 00000040 ffffffff 00000000 00000004 00000000 00000000 + CmdIntrOUT: 00000001 00000d06 0001000f 00000000 00000001 00000000 00000040 ffffffff 00000000 00000004 00000000 00000000 + ffffffff860008a784ce5ae212376300000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 + RetIntrOut: 00000003 00000d06 00000000 00000000 00000000 00000000 00000040 ffffffff 00000000 00000000 00000000 00000000 + RetIntrIn: 00000003 00000d05 00000000 00000000 00000000 00000000 00000040 ffffffff 00000000 00000000 00000000 00000000 + ffffffff860011a784ce5ae2123763612891b1020100000400000000000000000000000000000000000000000000000000000000000000000000000000000000
Signature · 1 line
2.30.1
Greg Kroah-Hartman
maintainerQuoted 28 lines · Hongren Zheng (Zenithal)
The old document for usbip protocol is misleading and hard to read:
* Some fields in header are incorrect
* Explanation of some fields are unclear or even wrong
* Padding of header (namely all headers have the same length) is not explicitly point out, which is crucial for stream protocol like TCPThese fixes are made through reading usbip kernel drivers and userland codes. Also I have implemented one usbip server.
Major changes:
* Document the correct field as described in the codebase.
* Document the padding in usbip headers. This is crucial for TCP stream hence these padding should be explicitly point out. In code these padding are implemented by a union of all headers.
* Fix two FIXME related to usbip unlink and Document the behavior of unlink in different situation.
* Clarify some field with more accurate explanation, like those fields associated with URB. Some constraints are extracted from code.
* Delete specifictransfer_flagdoc in usbip as it should be documented by the URB part.
* Add data captured from wire as exampleAlso some changes suggested by a previous patch in
https://lore.kernel.org/linux-usb/[email protected]/
is adopted in this patch.
Quoted 5 lines
Co-developed-by Alexandre Demers <[email protected]>Signed-off-by Hongren Zheng (Zenithal) <[email protected]>--- Documentation/usb/usbip_protocol.rst | 290 +++++++++++++++------------ 1 file changed, 159 insertions(+), 131 deletions(-)
What changed from v1? Always list that here below the --- line.
Documentation/usb/usbip_protocol.rst USB/IP protocol · line 9
Quoted 11 lines
Documentation/usb/usbip_protocol.rst +2
-0@@ -5,8 +5,14 @@ USB/IP protocol PRELIMINARY DRAFT, MAY CONTAIN MISTAKES! 28 Jun 2011 +Update: Fix major fields in protocol +14 Mar 2021
This does not belong here, the git changelog shows this information.
The original date above can be removed as well if you want. And if the mistakes are all fixed now, that line can be dropped too :)
thanks,
greg k-h
Hongren Zheng (Zenithal)
reviewerPATCH v3 1/1 docs: usbip: Fix major fields and descriptions in protocol
The old document for usbip protocol is misleading and hard to read:
* Some fields in header are incorrect
* Explanation of some fields are unclear or even wrong
* Padding of header (namely all headers have the same length) is not explicitly point out, which is crucial for stream protocol like TCP
These fixes are made through reading usbip kernel drivers and userland codes. Also I have implemented one usbip server.
Major changes:
* Document the correct field as described in the codebase.
* Document the padding in usbip headers. This is crucial for TCP stream hence these padding should be explicitly point out. In code these padding are implemented by a union of all headers.
* Fix two FIXME related to usbip unlink and Document the behavior of unlink in different situation.
* Clarify some field with more accurate explanation, like those fields associated with URB. Some constraints are extracted from code.
* Delete specific transfer_flag doc in usbip as it should be documented by the URB part.
* Add data captured from wire as example
PATCH v2:
Some changes suggested by a previous patch in
https://lore.kernel.org/linux-usb
/[email protected]/
is adopted in this patch.
* Fix Typo: duplicated 'the' in 'the following 4 field'
* Fix incorrect field: in OP_REQ_DEVLIST, the second dev starts with field 'path', not 'busid'
PATCH v3:
Suggested by
https://lore.kernel.org/linux-doc/YE8Oan2BmSuKR4%[email protected]/
* Remove date in doc as these are tracked in git history
* Remove 'mistake alert' as all data fields are documented properly now. However, docs on possible values for some field shall be added in the future
--- Documentation/usb/usbip_protocol.rst | 288 ++++++++++++++------------- 1 file changed, 155 insertions(+), 133 deletions(-)
Documentation/usb/usbip_protocol.rst +155 -133
@@ -2,11 +2,11 @@ USB/IP protocol =============== -PRELIMINARY DRAFT, MAY CONTAIN MISTAKES! -28 Jun 2011 +Architecture +============ The USB/IP protocol follows a server/client architecture. The server exports the -USB devices and the clients imports them. The device driver for the exported +USB devices and the client imports them. The device driver for the exported USB device runs on the client machine. The client may ask for the list of the exported USB devices. To get the list the
@@ -37,6 +37,9 @@ to transfer the URB traffic between the client and the server. The client may send two types of packets: the USBIP_CMD_SUBMIT to submit an URB, and USBIP_CMD_UNLINK to unlink a previously submitted URB. The answers of the server may be USBIP_RET_SUBMIT and USBIP_RET_UNLINK respectively. +Note that after successful USBIP_RET_UNLINK, the unlinked URB request would not +have a corresponding USBIP_RET_UNLINK (this is explained in +drivers/usb/usbip/stub_rx.c). ::
@@ -85,16 +88,42 @@ server may be USBIP_RET_SUBMIT and USBIP_RET_UNLINK respectively. | . | | : | | | + | USBIP_CMD_SUBMIT(seqnum = p) | + | ----------------------------------------------> | + | | | USBIP_CMD_UNLINK | + | (seqnum = p+1, unlink_seqnum = p) | | ----------------------------------------------> | | | | USBIP_RET_UNLINK | + | (seqnum = p+1, status = -ECONNRESET) | + | <---------------------------------------------- | + | | + | Note: No USBIP_RET_SUBMIT(seqnum = p) | + | <--X---X---X---X---X---X---X---X---X---X---X--- | + | . | + | : | + | | + | USBIP_CMD_SUBMIT(seqnum = q) | + | ----------------------------------------------> | + | | + | USBIP_RET_SUBMIT(seqnum = q) | + | <---------------------------------------------- | + | | + | USBIP_CMD_UNLINK | + | (seqnum = q+1, unlink_seqnum = q) | + | ----------------------------------------------> | + | | + | USBIP_RET_UNLINK | + | (seqnum = q+1, status = 0) | | <---------------------------------------------- | | | The fields are in network (big endian) byte order meaning that the most significant byte (MSB) is stored at the lowest address. +Message Format +============== OP_REQ_DEVLIST: Retrieve the list of exported USB devices.
@@ -102,7 +131,7 @@ OP_REQ_DEVLIST: +-----------+--------+------------+---------------------------------------------------+ | Offset | Length | Value | Description | +===========+========+============+===================================================+ -| 0 | 2 | 0x0100 | Binary-coded decimal USBIP version number: v1.0.0 | +| 0 | 2 | 0x0111 | Binary-coded decimal USBIP version number: v1.1.1 | +-----------+--------+------------+---------------------------------------------------+ | 2 | 2 | 0x8005 | Command code: Retrieve the list of exported USB | | | | | devices. |
@@ -116,7 +145,7 @@ OP_REP_DEVLIST: +-----------+--------+------------+---------------------------------------------------+ | Offset | Length | Value | Description | +===========+========+============+===================================================+ -| 0 | 2 | 0x0100 | Binary-coded decimal USBIP version number: v1.0.0.| +| 0 | 2 | 0x0111 | Binary-coded decimal USBIP version number: v1.1.1 | +-----------+--------+------------+---------------------------------------------------+ | 2 | 2 | 0x0005 | Reply code: The list of exported USB devices. | +-----------+--------+------------+---------------------------------------------------+
@@ -165,8 +194,8 @@ OP_REP_DEVLIST: | 0x143 | 1 | | bNumInterfaces | +-----------+--------+------------+---------------------------------------------------+ | 0x144 | | m_0 | From now on each interface is described, all | -| | | | together bNumInterfaces times, with the | -| | | | the following 4 fields: | +| | | | together bNumInterfaces times, with the following | +| | | | 4 fields: | +-----------+--------+------------+---------------------------------------------------+ | | 1 | | bInterfaceClass | +-----------+--------+------------+---------------------------------------------------+
@@ -177,7 +206,7 @@ OP_REP_DEVLIST: | 0x147 | 1 | | padding byte for alignment, shall be set to zero | +-----------+--------+------------+---------------------------------------------------+ | 0xC + | | | The second exported USB device starts at i=1 | -| i*0x138 + | | | with the busid field. | +| i*0x138 + | | | with the path field. | | m_(i-1)*4 | | | | +-----------+--------+------------+---------------------------------------------------+
@@ -187,7 +216,7 @@ OP_REQ_IMPORT: +-----------+--------+------------+---------------------------------------------------+ | Offset | Length | Value | Description | +===========+========+============+===================================================+ -| 0 | 2 | 0x0100 | Binary-coded decimal USBIP version number: v1.0.0 | +| 0 | 2 | 0x0111 | Binary-coded decimal USBIP version number: v1.1.1 | +-----------+--------+------------+---------------------------------------------------+ | 2 | 2 | 0x8003 | Command code: import a remote USB device. | +-----------+--------+------------+---------------------------------------------------+
@@ -206,7 +235,7 @@ OP_REP_IMPORT: +-----------+--------+------------+---------------------------------------------------+ | Offset | Length | Value | Description | +===========+========+============+===================================================+ -| 0 | 2 | 0x0100 | Binary-coded decimal USBIP version number: v1.0.0 | +| 0 | 2 | 0x0111 | Binary-coded decimal USBIP version number: v1.1.1 | +-----------+--------+------------+---------------------------------------------------+ | 2 | 2 | 0x0003 | Reply code: Reply to import. | +-----------+--------+------------+---------------------------------------------------+
@@ -254,65 +283,75 @@ OP_REP_IMPORT: | 0x13E | 1 | | bNumInterfaces | +-----------+--------+------------+---------------------------------------------------+ -USBIP_CMD_SUBMIT: - Submit an URB +The following four commands have a common basic header called +'usbip_header_basic', and their headers, called 'usbip_header' (before URB +payload), have the same length, therefore paddings are needed. -+-----------+--------+------------+---------------------------------------------------+ -| Offset | Length | Value | Description | -+===========+========+============+===================================================+ -| 0 | 4 | 0x00000001 | command: Submit an URB | -+-----------+--------+------------+---------------------------------------------------+ -| 4 | 4 | | seqnum: the sequence number of the URB to submit | -+-----------+--------+------------+---------------------------------------------------+ -| 8 | 4 | | devid | -+-----------+--------+------------+---------------------------------------------------+ -| 0xC | 4 | | direction: | -| | | | | -| | | | - 0: USBIP_DIR_OUT | -| | | | - 1: USBIP_DIR_IN | -+-----------+--------+------------+---------------------------------------------------+ -| 0x10 | 4 | | ep: endpoint number, possible values are: 0...15 | -+-----------+--------+------------+---------------------------------------------------+ -| 0x14 | 4 | | transfer_flags: possible values depend on the | -| | | | URB transfer type, see below | -+-----------+--------+------------+---------------------------------------------------+ -| 0x18 | 4 | | transfer_buffer_length | -+-----------+--------+------------+---------------------------------------------------+ -| 0x1C | 4 | | start_frame: specify the selected frame to | -| | | | transmit an ISO frame, ignored if URB_ISO_ASAP | -| | | | is specified at transfer_flags | -+-----------+--------+------------+---------------------------------------------------+ -| 0x20 | 4 | | number_of_packets: number of ISO packets | -+-----------+--------+------------+---------------------------------------------------+ -| 0x24 | 4 | | interval: maximum time for the request on the | -| | | | server-side host controller | -+-----------+--------+------------+---------------------------------------------------+ -| 0x28 | 8 | | setup: data bytes for USB setup, filled with | -| | | | zeros if not used | -+-----------+--------+------------+---------------------------------------------------+ -| 0x30 | | | URB data. For ISO transfers the padding between | -| | | | each ISO packets is not transmitted. | -+-----------+--------+------------+---------------------------------------------------+ +usbip_header_basic: ++-----------+--------+---------------------------------------------------+ +| Offset | Length | Description | ++===========+========+===================================================+ +| 0 | 4 | command | ++-----------+--------+---------------------------------------------------+ +| 4 | 4 | seqnum: sequential number that identifies requests| +| | | and corresponding responses; | +| | | incremented per connection | ++-----------+--------+---------------------------------------------------+ +| 8 | 4 | devid: specifies a remote USB device uniquely | +| | | instead of busnum and devnum; | +| | | for client (request), this value is | +| | | ((busnum << 16) | devnum); | +| | | for server (response), this shall be set to 0 | ++-----------+--------+---------------------------------------------------+ +| 0xC | 4 | direction: | +| | | | +| | | - 0: USBIP_DIR_OUT | +| | | - 1: USBIP_DIR_IN | +| | | | +| | | only used by client, for server this shall be 0 | ++-----------+--------+---------------------------------------------------+ +| 0x10 | 4 | ep: endpoint number | +| | | only used by client, for server this shall be 0 | +| | | for UNLINK, this shall be 0 | ++-----------+--------+---------------------------------------------------+ - +-------------------------+------------+---------+-----------+----------+-------------+ - | Allowed transfer_flags | value | control | interrupt | bulk | isochronous | - +=========================+============+=========+===========+==========+=============+ - | URB_SHORT_NOT_OK | 0x00000001 | only in | only in | only in | no | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_ISO_ASAP | 0x00000002 | no | no | no | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_NO_TRANSFER_DMA_MAP | 0x00000004 | yes | yes | yes | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_ZERO_PACKET | 0x00000040 | no | no | only out | no | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_NO_INTERRUPT | 0x00000080 | yes | yes | yes | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_FREE_BUFFER | 0x00000100 | yes | yes | yes | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_DIR_MASK | 0x00000200 | yes | yes | yes | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ +USBIP_CMD_SUBMIT: + Submit an URB ++-----------+--------+---------------------------------------------------+ +| Offset | Length | Description | ++===========+========+===================================================+ +| 0 | 20 | usbip_header_basic, 'command' shall be 0x00000001 | ++-----------+--------+---------------------------------------------------+ +| 0x14 | 4 | transfer_flags: possible values depend on the | +| | | URB transfer_flags, | +| | | but with URB_NO_TRANSFER_DMA_MAP masked | ++-----------+--------+---------------------------------------------------+ +| 0x18 | 4 | transfer_buffer_length: | +| | | use URB transfer_buffer_length | ++-----------+--------+---------------------------------------------------+ +| 0x1C | 4 | start_frame: use URB start_frame; | +| | | initial frame for ISO transfer | +| | | shall be set to 0 if not ISO transfer | ++-----------+--------+---------------------------------------------------+ +| 0x20 | 4 | number_of_packets: number of ISO packets | +| | | shall be set to 0xffffffff if not ISO transfer | ++-----------+--------+---------------------------------------------------+ +| 0x24 | 4 | interval: maximum time for the request on the | +| | | server-side host controller | ++-----------+--------+---------------------------------------------------+ +| 0x28 | 8 | setup: data bytes for USB setup, filled with | +| | | zeros if not used | ++-----------+--------+---------------------------------------------------+ +| 0x30 | n | tranfer_buffer. | +| | | If direction is USBIP_DIR_OUT then n equals | +| | | transfer_buffer_length; otherwise n equals 0 | +| | | For ISO transfers the padding between each ISO | +| | | between each ISO packets is not transmitted. | ++-----------+--------+---------------------------------------------------+ +| 0x30+n | m | iso_packet_descriptor | ++-----------+--------+---------------------------------------------------+ USBIP_RET_SUBMIT: Reply for submitting an URB
@@ -320,92 +359,75 @@ USBIP_RET_SUBMIT: +-----------+--------+------------+---------------------------------------------------+ | Offset | Length | Value | Description | +===========+========+============+===================================================+ -| 0 | 4 | 0x00000003 | command | -+-----------+--------+------------+---------------------------------------------------+ -| 4 | 4 | | seqnum: URB sequence number | -+-----------+--------+------------+---------------------------------------------------+ -| 8 | 4 | | devid | -+-----------+--------+------------+---------------------------------------------------+ -| 0xC | 4 | | direction: | -| | | | | -| | | | - 0: USBIP_DIR_OUT | -| | | | - 1: USBIP_DIR_IN | -+-----------+--------+------------+---------------------------------------------------+ -| 0x10 | 4 | | ep: endpoint number | +| 0 | 20 | | usbip_header_basic, 'command' shall be 0x00000003 | +-----------+--------+------------+---------------------------------------------------+ | 0x14 | 4 | | status: zero for successful URB transaction, | | | | | otherwise some kind of error happened. | +-----------+--------+------------+---------------------------------------------------+ | 0x18 | 4 | n | actual_length: number of URB data bytes | +| | | | use URB actual_length | +-----------+--------+------------+---------------------------------------------------+ -| 0x1C | 4 | | start_frame: for an ISO frame the actually | -| | | | selected frame for transmit. | +| 0x1C | 4 | | start_frame: use URB start_frame; | +| | | | initial frame for ISO transfer | +| | | | shall be set to 0 if not ISO transfer | +-----------+--------+------------+---------------------------------------------------+ -| 0x20 | 4 | | number_of_packets | +| 0x20 | 4 | | number_of_packets: number of ISO packets | +| | | | shall be set to 0xffffffff if not ISO transfer | +-----------+--------+------------+---------------------------------------------------+ | 0x24 | 4 | | error_count | +-----------+--------+------------+---------------------------------------------------+ -| 0x28 | 8 | | setup: data bytes for USB setup, filled with | -| | | | zeros if not used | +| 0x28 | 8 | | padding, shall be set to 0 | +-----------+--------+------------+---------------------------------------------------+ -| 0x30 | n | | URB data bytes. For ISO transfers the padding | +| 0x30 | n | | tranfer_buffer. | +| | | | If direction is USBIP_DIR_OUT then n equals | +| | | | transfer_buffer_length; otherwise n equals 0 | +| | | | For ISO transfers the padding between each ISO | | | | | between each ISO packets is not transmitted. | +-----------+--------+------------+---------------------------------------------------+ +| 0x30+n | m | | iso_packet_descriptor | ++-----------+--------+------------+---------------------------------------------------+ USBIP_CMD_UNLINK: Unlink an URB -+-----------+--------+------------+---------------------------------------------------+ -| Offset | Length | Value | Description | -+===========+========+============+===================================================+ -| 0 | 4 | 0x00000002 | command: URB unlink command | -+-----------+--------+------------+---------------------------------------------------+ -| 4 | 4 | | seqnum: URB sequence number to unlink: | -| | | | | -| | | | FIXME: | -| | | | is this so? | -+-----------+--------+------------+---------------------------------------------------+ -| 8 | 4 | | devid | -+-----------+--------+------------+---------------------------------------------------+ -| 0xC | 4 | | direction: | -| | | | | -| | | | - 0: USBIP_DIR_OUT | -| | | | - 1: USBIP_DIR_IN | -+-----------+--------+------------+---------------------------------------------------+ -| 0x10 | 4 | | ep: endpoint number: zero | -+-----------+--------+------------+---------------------------------------------------+ -| 0x14 | 4 | | seqnum: the URB sequence number given previously | -| | | | at USBIP_CMD_SUBMIT.seqnum field | -+-----------+--------+------------+---------------------------------------------------+ -| 0x30 | n | | URB data bytes. For ISO transfers the padding | -| | | | between each ISO packets is not transmitted. | -+-----------+--------+------------+---------------------------------------------------+ ++-----------+--------+---------------------------------------------------+ +| Offset | Length | Description | ++===========+========+===================================================+ +| 0 | 20 | usbip_header_basic, 'command' shall be 0x00000002 | ++-----------+--------+---------------------------------------------------+ +| 0x14 | 4 | unlink_seqnum, of the SUBMIT request to unlink | ++-----------+--------+---------------------------------------------------+ +| 0x18 | 24 | padding, shall be set to 0 | ++-----------+--------+---------------------------------------------------+ USBIP_RET_UNLINK: Reply for URB unlink -+-----------+--------+------------+---------------------------------------------------+ -| Offset | Length | Value | Description | -+===========+========+============+===================================================+ -| 0 | 4 | 0x00000004 | command: reply for the URB unlink command | -+-----------+--------+------------+---------------------------------------------------+ -| 4 | 4 | | seqnum: the unlinked URB sequence number | -+-----------+--------+------------+---------------------------------------------------+ -| 8 | 4 | | devid | -+-----------+--------+------------+---------------------------------------------------+ -| 0xC | 4 | | direction: | -| | | | | -| | | | - 0: USBIP_DIR_OUT | -| | | | - 1: USBIP_DIR_IN | -+-----------+--------+------------+---------------------------------------------------+ -| 0x10 | 4 | | ep: endpoint number | -+-----------+--------+------------+---------------------------------------------------+ -| 0x14 | 4 | | status: This is the value contained in the | -| | | | urb->status in the URB completition handler. | -| | | | | -| | | | FIXME: | -| | | | a better explanation needed. | -+-----------+--------+------------+---------------------------------------------------+ -| 0x30 | n | | URB data bytes. For ISO transfers the padding | -| | | | between each ISO packets is not transmitted. | -+-----------+--------+------------+---------------------------------------------------+ ++-----------+--------+---------------------------------------------------+ +| Offset | Length | Description | ++===========+========+===================================================+ +| 0 | 20 | usbip_header_basic, 'command' shall be 0x00000004 | ++-----------+--------+---------------------------------------------------+ +| 0x14 | 4 | status: This is similar to that status of | +| | | USBIP_RET_SUBMIT (share the same memory offset) | +| | | When UNLINK is successful, status is -ECONNRESET; | +| | | when USBIP_CMD_UNLINK is after USBIP_RET_SUBMIT | +| | | status is 0 | ++-----------+--------+---------------------------------------------------+ +| 0x18 | 24 | padding, shall be set to 0 | ++-----------+--------+---------------------------------------------------+ + +EXAMPLE +======= + + The following data is captured from wire with Human Interface Devices (HID) + payload + +:: + + CmdIntrIN: 00000001 00000d05 0001000f 00000001 00000001 00000200 00000040 ffffffff 00000000 00000004 00000000 00000000 + CmdIntrOUT: 00000001 00000d06 0001000f 00000000 00000001 00000000 00000040 ffffffff 00000000 00000004 00000000 00000000 + ffffffff860008a784ce5ae212376300000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 + RetIntrOut: 00000003 00000d06 00000000 00000000 00000000 00000000 00000040 ffffffff 00000000 00000000 00000000 00000000 + RetIntrIn: 00000003 00000d05 00000000 00000000 00000000 00000000 00000040 ffffffff 00000000 00000000 00000000 00000000 + ffffffff860011a784ce5ae2123763612891b1020100000400000000000000000000000000000000000000000000000000000000000000000000000000000000
Signature · 1 line
2.30.1
Randy Dunlap
reviewerHi,
Some comments inline.
Quoted 89 lines · Hongren Zheng (Zenithal)
The old document for usbip protocol is misleading and hard to read:
* Some fields in header are incorrect
* Explanation of some fields are unclear or even wrong
* Padding of header (namely all headers have the same length) is not explicitly point out, which is crucial for stream protocol like TCPThese fixes are made through reading usbip kernel drivers and userland codes. Also I have implemented one usbip server.
Major changes:
PATCH v2:
PATCH v3:
Co-developed-by Alexandre Demers <[email protected]>Signed-off-by Hongren Zheng (Zenithal) <[email protected]>--- Documentation/usb/usbip_protocol.rst | 288 ++++++++++++++------------- 1 file changed, 155 insertions(+), 133 deletions(-)Documentation/usb/usbip_protocol.rst +18
-38@@ -254,65 +283,75 @@ OP_REP_IMPORT: | 0x13E | 1 | | bNumInterfaces | +-----------+--------+------------+---------------------------------------------------+ -USBIP_CMD_SUBMIT: - Submit an URB +The following four commands have a common basic header called +'usbip_header_basic', and their headers, called 'usbip_header' (before URB +payload), have the same length, therefore paddings are needed. -+-----------+--------+------------+---------------------------------------------------+ -| Offset | Length | Value | Description | -+===========+========+============+===================================================+ -| 0 | 4 | 0x00000001 | command: Submit an URB | -+-----------+--------+------------+---------------------------------------------------+ -| 4 | 4 | | seqnum: the sequence number of the URB to submit | -+-----------+--------+------------+---------------------------------------------------+ -| 8 | 4 | | devid | -+-----------+--------+------------+---------------------------------------------------+ -| 0xC | 4 | | direction: | -| | | | | -| | | | - 0: USBIP_DIR_OUT | -| | | | - 1: USBIP_DIR_IN | -+-----------+--------+------------+---------------------------------------------------+ -| 0x10 | 4 | | ep: endpoint number, possible values are: 0...15 | -+-----------+--------+------------+---------------------------------------------------+ -| 0x14 | 4 | | transfer_flags: possible values depend on the | -| | | | URB transfer type, see below | -+-----------+--------+------------+---------------------------------------------------+ -| 0x18 | 4 | | transfer_buffer_length | -+-----------+--------+------------+---------------------------------------------------+ -| 0x1C | 4 | | start_frame: specify the selected frame to | -| | | | transmit an ISO frame, ignored if URB_ISO_ASAP | -| | | | is specified at transfer_flags | -+-----------+--------+------------+---------------------------------------------------+ -| 0x20 | 4 | | number_of_packets: number of ISO packets | -+-----------+--------+------------+---------------------------------------------------+ -| 0x24 | 4 | | interval: maximum time for the request on the | -| | | | server-side host controller | -+-----------+--------+------------+---------------------------------------------------+ -| 0x28 | 8 | | setup: data bytes for USB setup, filled with | -| | | | zeros if not used | -+-----------+--------+------------+---------------------------------------------------+ -| 0x30 | | | URB data. For ISO transfers the padding between | -| | | | each ISO packets is not transmitted. | -+-----------+--------+------------+---------------------------------------------------+ +usbip_header_basic: ++-----------+--------+---------------------------------------------------+ +| Offset | Length | Description | ++===========+========+===================================================+ +| 0 | 4 | command | ++-----------+--------+---------------------------------------------------+ +| 4 | 4 | seqnum: sequential number that identifies requests| +| | | and corresponding responses; | +| | | incremented per connection | ++-----------+--------+---------------------------------------------------+ +| 8 | 4 | devid: specifies a remote USB device uniquely | +| | | instead of busnum and devnum; | +| | | for client (request), this value is | +| | | ((busnum << 16) | devnum); | +| | | for server (response), this shall be set to 0 |
Documentation/usb/usbip_protocol.rst OP_REP_IMPORT: · line 315
Quoted 10 lines
Documentation/usb/usbip_protocol.rst +10
-0++-----------+--------+---------------------------------------------------+ +| 0xC | 4 | direction: | +| | | | +| | | - 0: USBIP_DIR_OUT | +| | | - 1: USBIP_DIR_IN | +| | | | +| | | only used by client, for server this shall be 0 | ++-----------+--------+---------------------------------------------------+ +| 0x10 | 4 | ep: endpoint number | +| | | only used by client, for server this shall be 0 |
This could use a ';' after the '0' above for better readability.
Quoted 27 lines
Documentation/usb/usbip_protocol.rst +8
-17+| | | for UNLINK, this shall be 0 | ++-----------+--------+---------------------------------------------------+ - +-------------------------+------------+---------+-----------+----------+-------------+ - | Allowed transfer_flags | value | control | interrupt | bulk | isochronous | - +=========================+============+=========+===========+==========+=============+ - | URB_SHORT_NOT_OK | 0x00000001 | only in | only in | only in | no | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_ISO_ASAP | 0x00000002 | no | no | no | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_NO_TRANSFER_DMA_MAP | 0x00000004 | yes | yes | yes | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_ZERO_PACKET | 0x00000040 | no | no | only out | no | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_NO_INTERRUPT | 0x00000080 | yes | yes | yes | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_FREE_BUFFER | 0x00000100 | yes | yes | yes | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_DIR_MASK | 0x00000200 | yes | yes | yes | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ +USBIP_CMD_SUBMIT: + Submit an URB ++-----------+--------+---------------------------------------------------+ +| Offset | Length | Description | ++===========+========+===================================================+ +| 0 | 20 | usbip_header_basic, 'command' shall be 0x00000001 |
Documentation/usb/usbip_protocol.rst OP_REP_IMPORT: · line 335
Quoted 10 lines
Documentation/usb/usbip_protocol.rst +10
-0++-----------+--------+---------------------------------------------------+ +| 0x14 | 4 | transfer_flags: possible values depend on the | +| | | URB transfer_flags, | +| | | but with URB_NO_TRANSFER_DMA_MAP masked | ++-----------+--------+---------------------------------------------------+ +| 0x18 | 4 | transfer_buffer_length: | +| | | use URB transfer_buffer_length | ++-----------+--------+---------------------------------------------------+ +| 0x1C | 4 | start_frame: use URB start_frame; | +| | | initial frame for ISO transfer |
transfer;
Documentation/usb/usbip_protocol.rst OP_REP_IMPORT: · line 338
Quoted 3 lines
Documentation/usb/usbip_protocol.rst +3
-0+| | | shall be set to 0 if not ISO transfer | ++-----------+--------+---------------------------------------------------+ +| 0x20 | 4 | number_of_packets: number of ISO packets |
packets;
Documentation/usb/usbip_protocol.rst OP_REP_IMPORT: · line 349
Quoted 11 lines
Documentation/usb/usbip_protocol.rst +11
-0+| | | shall be set to 0xffffffff if not ISO transfer | ++-----------+--------+---------------------------------------------------+ +| 0x24 | 4 | interval: maximum time for the request on the | +| | | server-side host controller | ++-----------+--------+---------------------------------------------------+ +| 0x28 | 8 | setup: data bytes for USB setup, filled with | +| | | zeros if not used | ++-----------+--------+---------------------------------------------------+ +| 0x30 | n | tranfer_buffer. | +| | | If direction is USBIP_DIR_OUT then n equals | +| | | transfer_buffer_length; otherwise n equals 0 |
equals 0.
Quoted 20 lines
Documentation/usb/usbip_protocol.rst +5
-8+| | | For ISO transfers the padding between each ISO | +| | | between each ISO packets is not transmitted. | ++-----------+--------+---------------------------------------------------+ +| 0x30+n | m | iso_packet_descriptor | ++-----------+--------+---------------------------------------------------+ USBIP_RET_SUBMIT: Reply for submitting an URB@@ -320,92 +359,75 @@ USBIP_RET_SUBMIT: +-----------+--------+------------+---------------------------------------------------+ | Offset | Length | Value | Description | +===========+========+============+===================================================+ -| 0 | 4 | 0x00000003 | command | -+-----------+--------+------------+---------------------------------------------------+ -| 4 | 4 | | seqnum: URB sequence number | -+-----------+--------+------------+---------------------------------------------------+ -| 8 | 4 | | devid | -+-----------+--------+------------+---------------------------------------------------+ -| 0xC | 4 | | direction: | -| | | | |
Documentation/usb/usbip_protocol.rst USBIP_RET_SUBMIT: · line 367
Quoted 10 lines
Documentation/usb/usbip_protocol.rst +1
-4-| | | | - 0: USBIP_DIR_OUT | -| | | | - 1: USBIP_DIR_IN | -+-----------+--------+------------+---------------------------------------------------+ -| 0x10 | 4 | | ep: endpoint number | +| 0 | 20 | | usbip_header_basic, 'command' shall be 0x00000003 | +-----------+--------+------------+---------------------------------------------------+ | 0x14 | 4 | | status: zero for successful URB transaction, | | | | | otherwise some kind of error happened. | +-----------+--------+------------+---------------------------------------------------+ | 0x18 | 4 | n | actual_length: number of URB data bytes |
bytes;
Documentation/usb/usbip_protocol.rst USBIP_RET_SUBMIT: · line 371
Quoted 6 lines
Documentation/usb/usbip_protocol.rst +3
-2+| | | | use URB actual_length | +-----------+--------+------------+---------------------------------------------------+ -| 0x1C | 4 | | start_frame: for an ISO frame the actually | -| | | | selected frame for transmit. | +| 0x1C | 4 | | start_frame: use URB start_frame; | +| | | | initial frame for ISO transfer |
transfer;
Documentation/usb/usbip_protocol.rst USBIP_RET_SUBMIT: · line 374
Quoted 4 lines
Documentation/usb/usbip_protocol.rst +2
-1+| | | | shall be set to 0 if not ISO transfer | +-----------+--------+------------+---------------------------------------------------+ -| 0x20 | 4 | | number_of_packets | +| 0x20 | 4 | | number_of_packets: number of ISO packets |
packets;
Documentation/usb/usbip_protocol.rst USBIP_RET_SUBMIT: · line 349
Quoted 6 lines
Documentation/usb/usbip_protocol.rst +1
-2+| | | | shall be set to 0xffffffff if not ISO transfer | +-----------+--------+------------+---------------------------------------------------+ | 0x24 | 4 | | error_count | +-----------+--------+------------+---------------------------------------------------+ -| 0x28 | 8 | | setup: data bytes for USB setup, filled with | -| | | | zeros if not used |
used;
Documentation/usb/usbip_protocol.rst USBIP_RET_SUBMIT: · line 381
Quoted 4 lines
Documentation/usb/usbip_protocol.rst +2
-1+| 0x28 | 8 | | padding, shall be set to 0 | +-----------+--------+------------+---------------------------------------------------+ -| 0x30 | n | | URB data bytes. For ISO transfers the padding | +| 0x30 | n | | tranfer_buffer. |
transfer_buffer.
Documentation/usb/usbip_protocol.rst USBIP_RET_SUBMIT: · line 383
Quoted 2 lines
Documentation/usb/usbip_protocol.rst +2
-0+| | | | If direction is USBIP_DIR_OUT then n equals | +| | | | transfer_buffer_length; otherwise n equals 0 |
equals 0.
Quoted 55 lines
Documentation/usb/usbip_protocol.rst +12
-33+| | | | For ISO transfers the padding between each ISO | | | | | between each ISO packets is not transmitted. | +-----------+--------+------------+---------------------------------------------------+ +| 0x30+n | m | | iso_packet_descriptor | ++-----------+--------+------------+---------------------------------------------------+ USBIP_CMD_UNLINK: Unlink an URB -+-----------+--------+------------+---------------------------------------------------+ -| Offset | Length | Value | Description | -+===========+========+============+===================================================+ -| 0 | 4 | 0x00000002 | command: URB unlink command | -+-----------+--------+------------+---------------------------------------------------+ -| 4 | 4 | | seqnum: URB sequence number to unlink: | -| | | | | -| | | | FIXME: | -| | | | is this so? | -+-----------+--------+------------+---------------------------------------------------+ -| 8 | 4 | | devid | -+-----------+--------+------------+---------------------------------------------------+ -| 0xC | 4 | | direction: | -| | | | | -| | | | - 0: USBIP_DIR_OUT | -| | | | - 1: USBIP_DIR_IN | -+-----------+--------+------------+---------------------------------------------------+ -| 0x10 | 4 | | ep: endpoint number: zero | -+-----------+--------+------------+---------------------------------------------------+ -| 0x14 | 4 | | seqnum: the URB sequence number given previously | -| | | | at USBIP_CMD_SUBMIT.seqnum field | -+-----------+--------+------------+---------------------------------------------------+ -| 0x30 | n | | URB data bytes. For ISO transfers the padding | -| | | | between each ISO packets is not transmitted. | -+-----------+--------+------------+---------------------------------------------------+ ++-----------+--------+---------------------------------------------------+ +| Offset | Length | Description | ++===========+========+===================================================+ +| 0 | 20 | usbip_header_basic, 'command' shall be 0x00000002 | ++-----------+--------+---------------------------------------------------+ +| 0x14 | 4 | unlink_seqnum, of the SUBMIT request to unlink | ++-----------+--------+---------------------------------------------------+ +| 0x18 | 24 | padding, shall be set to 0 | ++-----------+--------+---------------------------------------------------+ USBIP_RET_UNLINK: Reply for URB unlink -+-----------+--------+------------+---------------------------------------------------+ -| Offset | Length | Value | Description | -+===========+========+============+===================================================+ -| 0 | 4 | 0x00000004 | command: reply for the URB unlink command | -+-----------+--------+------------+---------------------------------------------------+ -| 4 | 4 | | seqnum: the unlinked URB sequence number | -+-----------+--------+------------+---------------------------------------------------+ -| 8 | 4 | | devid |
Documentation/usb/usbip_protocol.rst USBIP_RET_SUBMIT: · line 404
Quoted 10 lines
Documentation/usb/usbip_protocol.rst +0
-10-+-----------+--------+------------+---------------------------------------------------+ -| 0xC | 4 | | direction: | -| | | | | -| | | | - 0: USBIP_DIR_OUT | -| | | | - 1: USBIP_DIR_IN | -+-----------+--------+------------+---------------------------------------------------+ -| 0x10 | 4 | | ep: endpoint number | -+-----------+--------+------------+---------------------------------------------------+ -| 0x14 | 4 | | status: This is the value contained in the | -| | | | urb->status in the URB completition handler. |
completion
Documentation/usb/usbip_protocol.rst USBIP_RET_SUBMIT: · line 411
Quoted 13 lines
Documentation/usb/usbip_protocol.rst +6
-7-| | | | | -| | | | FIXME: | -| | | | a better explanation needed. | -+-----------+--------+------------+---------------------------------------------------+ -| 0x30 | n | | URB data bytes. For ISO transfers the padding | -| | | | between each ISO packets is not transmitted. | -+-----------+--------+------------+---------------------------------------------------+ ++-----------+--------+---------------------------------------------------+ +| Offset | Length | Description | ++===========+========+===================================================+ +| 0 | 20 | usbip_header_basic, 'command' shall be 0x00000004 | ++-----------+--------+---------------------------------------------------+ +| 0x14 | 4 | status: This is similar to that status of |
to the status of
Documentation/usb/usbip_protocol.rst USBIP_RET_SUBMIT: · line 412
Quoted 1 line
Documentation/usb/usbip_protocol.rst +1
-0+| | | USBIP_RET_SUBMIT (share the same memory offset) |
offset).
Documentation/usb/usbip_protocol.rst USBIP_RET_SUBMIT: · line 421
Quoted 8 lines
Documentation/usb/usbip_protocol.rst +8
-0+| | | When UNLINK is successful, status is -ECONNRESET; | +| | | when USBIP_CMD_UNLINK is after USBIP_RET_SUBMIT | +| | | status is 0 |> ++-----------+--------+---------------------------------------------------+ +| 0x18 | 24 | padding, shall be set to 0 | ++-----------+--------+---------------------------------------------------+ + +EXAMPLE +=======
HTH.
Signature · 1 line
~Randy
Hongren Zheng (Zenithal)
reviewerPATCH v4 1/1 docs: usbip: Fix major fields and descriptions in protocol
In reply to Hongren Zheng (Zenithal)The old document for usbip protocol is misleading and hard to read:
* Some fields in header are incorrect
* Explanation of some fields are unclear or even wrong
* Padding of header (namely all headers have the same length) is not explicitly pointed out, which is crucial for stream protocol like TCP
Major changes:
* Document the correct field as described in the codebase.
* Document the padding in usbip headers. This is crucial for TCP stream hence these padding should be explicitly point out. In code these padding are implemented by a union of all headers.
* Fix two FIXME related to usbip unlink and Document the behavior of unlink in different situation.
* Clarify some field with more accurate explanation, like those fields associated with URB. Some constraints are extracted from code.
* Delete specific transfer_flag doc in usbip as it should be documented by the URB part.
* Add data captured from wire as example
--- Documentation/usb/usbip_protocol.rst | 320 ++++++++++++++------------- 1 file changed, 171 insertions(+), 149 deletions(-)
PATCH v2:
Some changes suggested by a previous patch in
https://lore.kernel.org/linux-usb
/[email protected]/
is adopted in this patch.
* Fix Typo: duplicated 'the' in 'the following 4 field'
* Fix incorrect field: in OP_REQ_DEVLIST, the second dev starts with field 'path', not 'busid'
PATCH v3:
Suggested by
https://lore.kernel.org/linux-doc/YE8Oan2BmSuKR4%[email protected]/
* Remove date and changelog in doc as these are tracked in git history
* Remove 'mistake alert' as all data fields are documented properly now. However, docs on possible values for some field shall be added in the future
PATCH v4:
Suggested by https://lore.kernel.org/linux-doc
/[email protected]/
* Add punctuations for readability
* Move patch changelog after the marker line
* Remove nickname in signed-off-by line
Documentation/usb/usbip_protocol.rst +171 -149
@@ -2,11 +2,11 @@ USB/IP protocol =============== -PRELIMINARY DRAFT, MAY CONTAIN MISTAKES! -28 Jun 2011 +Architecture +============ The USB/IP protocol follows a server/client architecture. The server exports the -USB devices and the clients imports them. The device driver for the exported +USB devices and the client imports them. The device driver for the exported USB device runs on the client machine. The client may ask for the list of the exported USB devices. To get the list the
@@ -37,6 +37,9 @@ to transfer the URB traffic between the client and the server. The client may send two types of packets: the USBIP_CMD_SUBMIT to submit an URB, and USBIP_CMD_UNLINK to unlink a previously submitted URB. The answers of the server may be USBIP_RET_SUBMIT and USBIP_RET_UNLINK respectively. +Note that after successful USBIP_RET_UNLINK, the unlinked URB request would not +have a corresponding USBIP_RET_UNLINK (this is explained in +drivers/usb/usbip/stub_rx.c). ::
@@ -85,16 +88,42 @@ server may be USBIP_RET_SUBMIT and USBIP_RET_UNLINK respectively. | . | | : | | | + | USBIP_CMD_SUBMIT(seqnum = p) | + | ----------------------------------------------> | + | | + | USBIP_CMD_UNLINK | + | (seqnum = p+1, unlink_seqnum = p) | + | ----------------------------------------------> | + | | + | USBIP_RET_UNLINK | + | (seqnum = p+1, status = -ECONNRESET) | + | <---------------------------------------------- | + | | + | Note: No USBIP_RET_SUBMIT(seqnum = p) | + | <--X---X---X---X---X---X---X---X---X---X---X--- | + | . | + | : | + | | + | USBIP_CMD_SUBMIT(seqnum = q) | + | ----------------------------------------------> | + | | + | USBIP_RET_SUBMIT(seqnum = q) | + | <---------------------------------------------- | + | | | USBIP_CMD_UNLINK | + | (seqnum = q+1, unlink_seqnum = q) | | ----------------------------------------------> | | | | USBIP_RET_UNLINK | + | (seqnum = q+1, status = 0) | | <---------------------------------------------- | | | The fields are in network (big endian) byte order meaning that the most significant byte (MSB) is stored at the lowest address. +Message Format +============== OP_REQ_DEVLIST: Retrieve the list of exported USB devices.
@@ -102,7 +131,7 @@ OP_REQ_DEVLIST: +-----------+--------+------------+---------------------------------------------------+ | Offset | Length | Value | Description | +===========+========+============+===================================================+ -| 0 | 2 | 0x0100 | Binary-coded decimal USBIP version number: v1.0.0 | +| 0 | 2 | 0x0111 | Binary-coded decimal USBIP version number: v1.1.1 | +-----------+--------+------------+---------------------------------------------------+ | 2 | 2 | 0x8005 | Command code: Retrieve the list of exported USB | | | | | devices. |
@@ -116,7 +145,7 @@ OP_REP_DEVLIST: +-----------+--------+------------+---------------------------------------------------+ | Offset | Length | Value | Description | +===========+========+============+===================================================+ -| 0 | 2 | 0x0100 | Binary-coded decimal USBIP version number: v1.0.0.| +| 0 | 2 | 0x0111 | Binary-coded decimal USBIP version number: v1.1.1 | +-----------+--------+------------+---------------------------------------------------+ | 2 | 2 | 0x0005 | Reply code: The list of exported USB devices. | +-----------+--------+------------+---------------------------------------------------+
@@ -165,8 +194,8 @@ OP_REP_DEVLIST: | 0x143 | 1 | | bNumInterfaces | +-----------+--------+------------+---------------------------------------------------+ | 0x144 | | m_0 | From now on each interface is described, all | -| | | | together bNumInterfaces times, with the | -| | | | the following 4 fields: | +| | | | together bNumInterfaces times, with the following | +| | | | 4 fields: | +-----------+--------+------------+---------------------------------------------------+ | | 1 | | bInterfaceClass | +-----------+--------+------------+---------------------------------------------------+
@@ -177,7 +206,7 @@ OP_REP_DEVLIST: | 0x147 | 1 | | padding byte for alignment, shall be set to zero | +-----------+--------+------------+---------------------------------------------------+ | 0xC + | | | The second exported USB device starts at i=1 | -| i*0x138 + | | | with the busid field. | +| i*0x138 + | | | with the path field. | | m_(i-1)*4 | | | | +-----------+--------+------------+---------------------------------------------------+
@@ -187,7 +216,7 @@ OP_REQ_IMPORT: +-----------+--------+------------+---------------------------------------------------+ | Offset | Length | Value | Description | +===========+========+============+===================================================+ -| 0 | 2 | 0x0100 | Binary-coded decimal USBIP version number: v1.0.0 | +| 0 | 2 | 0x0111 | Binary-coded decimal USBIP version number: v1.1.1 | +-----------+--------+------------+---------------------------------------------------+ | 2 | 2 | 0x8003 | Command code: import a remote USB device. | +-----------+--------+------------+---------------------------------------------------+
@@ -206,7 +235,7 @@ OP_REP_IMPORT: +-----------+--------+------------+---------------------------------------------------+ | Offset | Length | Value | Description | +===========+========+============+===================================================+ -| 0 | 2 | 0x0100 | Binary-coded decimal USBIP version number: v1.0.0 | +| 0 | 2 | 0x0111 | Binary-coded decimal USBIP version number: v1.1.1 | +-----------+--------+------------+---------------------------------------------------+ | 2 | 2 | 0x0003 | Reply code: Reply to import. | +-----------+--------+------------+---------------------------------------------------+
@@ -254,158 +283,151 @@ OP_REP_IMPORT: | 0x13E | 1 | | bNumInterfaces | +-----------+--------+------------+---------------------------------------------------+ -USBIP_CMD_SUBMIT: - Submit an URB +The following four commands have a common basic header called +'usbip_header_basic', and their headers, called 'usbip_header' (before URB +payload), have the same length, therefore paddings are needed. -+-----------+--------+------------+---------------------------------------------------+ -| Offset | Length | Value | Description | -+===========+========+============+===================================================+ -| 0 | 4 | 0x00000001 | command: Submit an URB | -+-----------+--------+------------+---------------------------------------------------+ -| 4 | 4 | | seqnum: the sequence number of the URB to submit | -+-----------+--------+------------+---------------------------------------------------+ -| 8 | 4 | | devid | -+-----------+--------+------------+---------------------------------------------------+ -| 0xC | 4 | | direction: | -| | | | | -| | | | - 0: USBIP_DIR_OUT | -| | | | - 1: USBIP_DIR_IN | -+-----------+--------+------------+---------------------------------------------------+ -| 0x10 | 4 | | ep: endpoint number, possible values are: 0...15 | -+-----------+--------+------------+---------------------------------------------------+ -| 0x14 | 4 | | transfer_flags: possible values depend on the | -| | | | URB transfer type, see below | -+-----------+--------+------------+---------------------------------------------------+ -| 0x18 | 4 | | transfer_buffer_length | -+-----------+--------+------------+---------------------------------------------------+ -| 0x1C | 4 | | start_frame: specify the selected frame to | -| | | | transmit an ISO frame, ignored if URB_ISO_ASAP | -| | | | is specified at transfer_flags | -+-----------+--------+------------+---------------------------------------------------+ -| 0x20 | 4 | | number_of_packets: number of ISO packets | -+-----------+--------+------------+---------------------------------------------------+ -| 0x24 | 4 | | interval: maximum time for the request on the | -| | | | server-side host controller | -+-----------+--------+------------+---------------------------------------------------+ -| 0x28 | 8 | | setup: data bytes for USB setup, filled with | -| | | | zeros if not used | -+-----------+--------+------------+---------------------------------------------------+ -| 0x30 | | | URB data. For ISO transfers the padding between | -| | | | each ISO packets is not transmitted. | -+-----------+--------+------------+---------------------------------------------------+ +usbip_header_basic: ++-----------+--------+---------------------------------------------------+ +| Offset | Length | Description | ++===========+========+===================================================+ +| 0 | 4 | command | ++-----------+--------+---------------------------------------------------+ +| 4 | 4 | seqnum: sequential number that identifies requests| +| | | and corresponding responses; | +| | | incremented per connection | ++-----------+--------+---------------------------------------------------+ +| 8 | 4 | devid: specifies a remote USB device uniquely | +| | | instead of busnum and devnum; | +| | | for client (request), this value is | +| | | ((busnum << 16) | devnum); | +| | | for server (response), this shall be set to 0 | ++-----------+--------+---------------------------------------------------+ +| 0xC | 4 | direction: | +| | | | +| | | - 0: USBIP_DIR_OUT | +| | | - 1: USBIP_DIR_IN | +| | | | +| | | only used by client, for server this shall be 0 | ++-----------+--------+---------------------------------------------------+ +| 0x10 | 4 | ep: endpoint number | +| | | only used by client, for server this shall be 0; | +| | | for UNLINK, this shall be 0 | ++-----------+--------+---------------------------------------------------+ - +-------------------------+------------+---------+-----------+----------+-------------+ - | Allowed transfer_flags | value | control | interrupt | bulk | isochronous | - +=========================+============+=========+===========+==========+=============+ - | URB_SHORT_NOT_OK | 0x00000001 | only in | only in | only in | no | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_ISO_ASAP | 0x00000002 | no | no | no | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_NO_TRANSFER_DMA_MAP | 0x00000004 | yes | yes | yes | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_ZERO_PACKET | 0x00000040 | no | no | only out | no | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_NO_INTERRUPT | 0x00000080 | yes | yes | yes | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_FREE_BUFFER | 0x00000100 | yes | yes | yes | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_DIR_MASK | 0x00000200 | yes | yes | yes | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ +USBIP_CMD_SUBMIT: + Submit an URB ++-----------+--------+---------------------------------------------------+ +| Offset | Length | Description | ++===========+========+===================================================+ +| 0 | 20 | usbip_header_basic, 'command' shall be 0x00000001 | ++-----------+--------+---------------------------------------------------+ +| 0x14 | 4 | transfer_flags: possible values depend on the | +| | | URB transfer_flags, | +| | | but with URB_NO_TRANSFER_DMA_MAP masked | ++-----------+--------+---------------------------------------------------+ +| 0x18 | 4 | transfer_buffer_length: | +| | | use URB transfer_buffer_length | ++-----------+--------+---------------------------------------------------+ +| 0x1C | 4 | start_frame: use URB start_frame; | +| | | initial frame for ISO transfer; | +| | | shall be set to 0 if not ISO transfer | ++-----------+--------+---------------------------------------------------+ +| 0x20 | 4 | number_of_packets: number of ISO packets; | +| | | shall be set to 0xffffffff if not ISO transfer | ++-----------+--------+---------------------------------------------------+ +| 0x24 | 4 | interval: maximum time for the request on the | +| | | server-side host controller | ++-----------+--------+---------------------------------------------------+ +| 0x28 | 8 | setup: data bytes for USB setup, filled with | +| | | zeros if not used. | ++-----------+--------+---------------------------------------------------+ +| 0x30 | n | transfer_buffer. | +| | | If direction is USBIP_DIR_OUT then n equals | +| | | transfer_buffer_length; otherwise n equals 0. | +| | | For ISO transfers the padding between each ISO | +| | | packets is not transmitted. | ++-----------+--------+---------------------------------------------------+ +| 0x30+n | m | iso_packet_descriptor | ++-----------+--------+---------------------------------------------------+ USBIP_RET_SUBMIT: Reply for submitting an URB -+-----------+--------+------------+---------------------------------------------------+ -| Offset | Length | Value | Description | -+===========+========+============+===================================================+ -| 0 | 4 | 0x00000003 | command | -+-----------+--------+------------+---------------------------------------------------+ -| 4 | 4 | | seqnum: URB sequence number | -+-----------+--------+------------+---------------------------------------------------+ -| 8 | 4 | | devid | -+-----------+--------+------------+---------------------------------------------------+ -| 0xC | 4 | | direction: | -| | | | | -| | | | - 0: USBIP_DIR_OUT | -| | | | - 1: USBIP_DIR_IN | -+-----------+--------+------------+---------------------------------------------------+ -| 0x10 | 4 | | ep: endpoint number | -+-----------+--------+------------+---------------------------------------------------+ -| 0x14 | 4 | | status: zero for successful URB transaction, | -| | | | otherwise some kind of error happened. | -+-----------+--------+------------+---------------------------------------------------+ -| 0x18 | 4 | n | actual_length: number of URB data bytes | -+-----------+--------+------------+---------------------------------------------------+ -| 0x1C | 4 | | start_frame: for an ISO frame the actually | -| | | | selected frame for transmit. | -+-----------+--------+------------+---------------------------------------------------+ -| 0x20 | 4 | | number_of_packets | -+-----------+--------+------------+---------------------------------------------------+ -| 0x24 | 4 | | error_count | -+-----------+--------+------------+---------------------------------------------------+ -| 0x28 | 8 | | setup: data bytes for USB setup, filled with | -| | | | zeros if not used | -+-----------+--------+------------+---------------------------------------------------+ -| 0x30 | n | | URB data bytes. For ISO transfers the padding | -| | | | between each ISO packets is not transmitted. | -+-----------+--------+------------+---------------------------------------------------+ ++-----------+--------+---------------------------------------------------+ +| Offset | Length | Description | ++===========+========+===================================================+ +| 0 | 20 | usbip_header_basic, 'command' shall be 0x00000003 | ++-----------+--------+---------------------------------------------------+ +| 0x14 | 4 | status: zero for successful URB transaction, | +| | | otherwise some kind of error happened. | ++-----------+--------+---------------------------------------------------+ +| 0x18 | 4 | actual_length: number of URB data bytes; | +| | | use URB actual_length | ++-----------+--------+---------------------------------------------------+ +| 0x1C | 4 | start_frame: use URB start_frame; | +| | | initial frame for ISO transfer; | +| | | shall be set to 0 if not ISO transfer | ++-----------+--------+---------------------------------------------------+ +| 0x20 | 4 | number_of_packets: number of ISO packets; | +| | | shall be set to 0xffffffff if not ISO transfer | ++-----------+--------+---------------------------------------------------+ +| 0x24 | 4 | error_count | ++-----------+--------+---------------------------------------------------+ +| 0x28 | 8 | padding, shall be set to 0 | ++-----------+--------+---------------------------------------------------+ +| 0x30 | n | transfer_buffer. | +| | | If direction is USBIP_DIR_IN then n equals | +| | | actual_length; otherwise n equals 0. | +| | | For ISO transfers the padding between each ISO | +| | | packets is not transmitted. | ++-----------+--------+---------------------------------------------------+ +| 0x30+n | m | iso_packet_descriptor | ++-----------+--------+---------------------------------------------------+ USBIP_CMD_UNLINK: Unlink an URB -+-----------+--------+------------+---------------------------------------------------+ -| Offset | Length | Value | Description | -+===========+========+============+===================================================+ -| 0 | 4 | 0x00000002 | command: URB unlink command | -+-----------+--------+------------+---------------------------------------------------+ -| 4 | 4 | | seqnum: URB sequence number to unlink: | -| | | | | -| | | | FIXME: | -| | | | is this so? | -+-----------+--------+------------+---------------------------------------------------+ -| 8 | 4 | | devid | -+-----------+--------+------------+---------------------------------------------------+ -| 0xC | 4 | | direction: | -| | | | | -| | | | - 0: USBIP_DIR_OUT | -| | | | - 1: USBIP_DIR_IN | -+-----------+--------+------------+---------------------------------------------------+ -| 0x10 | 4 | | ep: endpoint number: zero | -+-----------+--------+------------+---------------------------------------------------+ -| 0x14 | 4 | | seqnum: the URB sequence number given previously | -| | | | at USBIP_CMD_SUBMIT.seqnum field | -+-----------+--------+------------+---------------------------------------------------+ -| 0x30 | n | | URB data bytes. For ISO transfers the padding | -| | | | between each ISO packets is not transmitted. | -+-----------+--------+------------+---------------------------------------------------+ ++-----------+--------+---------------------------------------------------+ +| Offset | Length | Description | ++===========+========+===================================================+ +| 0 | 20 | usbip_header_basic, 'command' shall be 0x00000002 | ++-----------+--------+---------------------------------------------------+ +| 0x14 | 4 | unlink_seqnum, of the SUBMIT request to unlink | ++-----------+--------+---------------------------------------------------+ +| 0x18 | 24 | padding, shall be set to 0 | ++-----------+--------+---------------------------------------------------+ USBIP_RET_UNLINK: Reply for URB unlink -+-----------+--------+------------+---------------------------------------------------+ -| Offset | Length | Value | Description | -+===========+========+============+===================================================+ -| 0 | 4 | 0x00000004 | command: reply for the URB unlink command | -+-----------+--------+------------+---------------------------------------------------+ -| 4 | 4 | | seqnum: the unlinked URB sequence number | -+-----------+--------+------------+---------------------------------------------------+ -| 8 | 4 | | devid | -+-----------+--------+------------+---------------------------------------------------+ -| 0xC | 4 | | direction: | -| | | | | -| | | | - 0: USBIP_DIR_OUT | -| | | | - 1: USBIP_DIR_IN | -+-----------+--------+------------+---------------------------------------------------+ -| 0x10 | 4 | | ep: endpoint number | -+-----------+--------+------------+---------------------------------------------------+ -| 0x14 | 4 | | status: This is the value contained in the | -| | | | urb->status in the URB completition handler. | -| | | | | -| | | | FIXME: | -| | | | a better explanation needed. | -+-----------+--------+------------+---------------------------------------------------+ -| 0x30 | n | | URB data bytes. For ISO transfers the padding | -| | | | between each ISO packets is not transmitted. | -+-----------+--------+------------+---------------------------------------------------+ ++-----------+--------+---------------------------------------------------+ +| Offset | Length | Description | ++===========+========+===================================================+ +| 0 | 20 | usbip_header_basic, 'command' shall be 0x00000004 | ++-----------+--------+---------------------------------------------------+ +| 0x14 | 4 | status: This is similar to the status of | +| | | USBIP_RET_SUBMIT (share the same memory offset). | +| | | When UNLINK is successful, status is -ECONNRESET; | +| | | when USBIP_CMD_UNLINK is after USBIP_RET_SUBMIT | +| | | status is 0 | ++-----------+--------+---------------------------------------------------+ +| 0x18 | 24 | padding, shall be set to 0 | ++-----------+--------+---------------------------------------------------+ + +EXAMPLE +======= + + The following data is captured from wire with Human Interface Devices (HID) + payload + +:: + + CmdIntrIN: 00000001 00000d05 0001000f 00000001 00000001 00000200 00000040 ffffffff 00000000 00000004 00000000 00000000 + CmdIntrOUT: 00000001 00000d06 0001000f 00000000 00000001 00000000 00000040 ffffffff 00000000 00000004 00000000 00000000 + ffffffff860008a784ce5ae212376300000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 + RetIntrOut: 00000003 00000d06 00000000 00000000 00000000 00000000 00000040 ffffffff 00000000 00000000 00000000 00000000 + RetIntrIn: 00000003 00000d05 00000000 00000000 00000000 00000000 00000040 ffffffff 00000000 00000000 00000000 00000000 + ffffffff860011a784ce5ae2123763612891b1020100000400000000000000000000000000000000000000000000000000000000000000000000000000000000
Signature · 1 line
2.30.1
Quoted 3 lines · Hongren Zheng (Zenithal)
Co-developed-by Alexandre Demers <[email protected]>Co-developed-by Randy Dunlap <[email protected]>
No, I'm not in the Co-developed-by loop here.
And then you can add:
Quoted 17 lines
Signed-off-by Hongren Zheng <[email protected]>--- Documentation/usb/usbip_protocol.rst | 320 ++++++++++++++------------- 1 file changed, 171 insertions(+), 149 deletions(-)PATCH v4:
Suggested by https://lore.kernel.org/linux-doc
/[email protected]/
* Add punctuations for readability
* Move patch changelog after the marker line
* Remove nickname in signed-off-by lineDocumentation/usb/usbip_protocol.rst +0
-0
Signature · 1 line
~Randy
Hongren Zheng (Zenithal)
reviewerPATCH v5 1/1 docs: usbip: Fix major fields and descriptions in protocol
In reply to Hongren Zheng (Zenithal)The old document for usbip protocol is misleading and hard to read:
* Some fields in header are incorrect
* Explanation of some fields are unclear or even wrong
* Padding of header (namely all headers have the same length) is not explicitly pointed out, which is crucial for stream protocol like TCP
Major changes:
* Document the correct field as described in the codebase.
* Document the padding in usbip headers. This is crucial for TCP stream hence these padding should be explicitly point out. In code these padding are implemented by a union of all headers.
* Fix two FIXME related to usbip unlink and Document the behavior of unlink in different situation.
* Clarify some field with more accurate explanation, like those fields associated with URB. Some constraints are extracted from code.
* Delete specific transfer_flag doc in usbip as it should be documented by the URB part.
* Add data captured from wire as example
--- Documentation/usb/usbip_protocol.rst | 320 ++++++++++++++------------- 1 file changed, 171 insertions(+), 149 deletions(-)
PATCH v2:
Some changes suggested by a previous patch in
https://lore.kernel.org/linux-usb
/[email protected]/
is adopted in this patch.
* Fix Typo: duplicated 'the' in 'the following 4 field'
* Fix incorrect field: in OP_REQ_DEVLIST, the second dev starts with field 'path', not 'busid'
PATCH v3:
Suggested by
https://lore.kernel.org/linux-doc/YE8Oan2BmSuKR4%[email protected]/
* Remove date and changelog in doc as these are tracked in git history
* Remove 'mistake alert' as all data fields are documented properly now. However, docs on possible values for some field shall be added in the future
PATCH v4:
Suggested by https://lore.kernel.org/linux-doc
/[email protected]/
* Add punctuations for readability
* Move patch changelog after the marker line
* Remove nickname in signed-off-by line
PATCH v5:
* Instead of co-developed-by, use reviewed-by
for Randy Dunlap
Documentation/usb/usbip_protocol.rst +171 -149
@@ -2,11 +2,11 @@ USB/IP protocol =============== -PRELIMINARY DRAFT, MAY CONTAIN MISTAKES! -28 Jun 2011 +Architecture +============ The USB/IP protocol follows a server/client architecture. The server exports the -USB devices and the clients imports them. The device driver for the exported +USB devices and the client imports them. The device driver for the exported USB device runs on the client machine. The client may ask for the list of the exported USB devices. To get the list the
@@ -37,6 +37,9 @@ to transfer the URB traffic between the client and the server. The client may send two types of packets: the USBIP_CMD_SUBMIT to submit an URB, and USBIP_CMD_UNLINK to unlink a previously submitted URB. The answers of the server may be USBIP_RET_SUBMIT and USBIP_RET_UNLINK respectively. +Note that after successful USBIP_RET_UNLINK, the unlinked URB request would not +have a corresponding USBIP_RET_UNLINK (this is explained in +drivers/usb/usbip/stub_rx.c). ::
@@ -85,16 +88,42 @@ server may be USBIP_RET_SUBMIT and USBIP_RET_UNLINK respectively. | . | | : | | | + | USBIP_CMD_SUBMIT(seqnum = p) | + | ----------------------------------------------> | + | | + | USBIP_CMD_UNLINK | + | (seqnum = p+1, unlink_seqnum = p) | + | ----------------------------------------------> | + | | + | USBIP_RET_UNLINK | + | (seqnum = p+1, status = -ECONNRESET) | + | <---------------------------------------------- | + | | + | Note: No USBIP_RET_SUBMIT(seqnum = p) | + | <--X---X---X---X---X---X---X---X---X---X---X--- | + | . | + | : | + | | + | USBIP_CMD_SUBMIT(seqnum = q) | + | ----------------------------------------------> | + | | + | USBIP_RET_SUBMIT(seqnum = q) | + | <---------------------------------------------- | + | | | USBIP_CMD_UNLINK | + | (seqnum = q+1, unlink_seqnum = q) | | ----------------------------------------------> | | | | USBIP_RET_UNLINK | + | (seqnum = q+1, status = 0) | | <---------------------------------------------- | | | The fields are in network (big endian) byte order meaning that the most significant byte (MSB) is stored at the lowest address. +Message Format +============== OP_REQ_DEVLIST: Retrieve the list of exported USB devices.
@@ -102,7 +131,7 @@ OP_REQ_DEVLIST: +-----------+--------+------------+---------------------------------------------------+ | Offset | Length | Value | Description | +===========+========+============+===================================================+ -| 0 | 2 | 0x0100 | Binary-coded decimal USBIP version number: v1.0.0 | +| 0 | 2 | 0x0111 | Binary-coded decimal USBIP version number: v1.1.1 | +-----------+--------+------------+---------------------------------------------------+ | 2 | 2 | 0x8005 | Command code: Retrieve the list of exported USB | | | | | devices. |
@@ -116,7 +145,7 @@ OP_REP_DEVLIST: +-----------+--------+------------+---------------------------------------------------+ | Offset | Length | Value | Description | +===========+========+============+===================================================+ -| 0 | 2 | 0x0100 | Binary-coded decimal USBIP version number: v1.0.0.| +| 0 | 2 | 0x0111 | Binary-coded decimal USBIP version number: v1.1.1 | +-----------+--------+------------+---------------------------------------------------+ | 2 | 2 | 0x0005 | Reply code: The list of exported USB devices. | +-----------+--------+------------+---------------------------------------------------+
@@ -165,8 +194,8 @@ OP_REP_DEVLIST: | 0x143 | 1 | | bNumInterfaces | +-----------+--------+------------+---------------------------------------------------+ | 0x144 | | m_0 | From now on each interface is described, all | -| | | | together bNumInterfaces times, with the | -| | | | the following 4 fields: | +| | | | together bNumInterfaces times, with the following | +| | | | 4 fields: | +-----------+--------+------------+---------------------------------------------------+ | | 1 | | bInterfaceClass | +-----------+--------+------------+---------------------------------------------------+
@@ -177,7 +206,7 @@ OP_REP_DEVLIST: | 0x147 | 1 | | padding byte for alignment, shall be set to zero | +-----------+--------+------------+---------------------------------------------------+ | 0xC + | | | The second exported USB device starts at i=1 | -| i*0x138 + | | | with the busid field. | +| i*0x138 + | | | with the path field. | | m_(i-1)*4 | | | | +-----------+--------+------------+---------------------------------------------------+
@@ -187,7 +216,7 @@ OP_REQ_IMPORT: +-----------+--------+------------+---------------------------------------------------+ | Offset | Length | Value | Description | +===========+========+============+===================================================+ -| 0 | 2 | 0x0100 | Binary-coded decimal USBIP version number: v1.0.0 | +| 0 | 2 | 0x0111 | Binary-coded decimal USBIP version number: v1.1.1 | +-----------+--------+------------+---------------------------------------------------+ | 2 | 2 | 0x8003 | Command code: import a remote USB device. | +-----------+--------+------------+---------------------------------------------------+
@@ -206,7 +235,7 @@ OP_REP_IMPORT: +-----------+--------+------------+---------------------------------------------------+ | Offset | Length | Value | Description | +===========+========+============+===================================================+ -| 0 | 2 | 0x0100 | Binary-coded decimal USBIP version number: v1.0.0 | +| 0 | 2 | 0x0111 | Binary-coded decimal USBIP version number: v1.1.1 | +-----------+--------+------------+---------------------------------------------------+ | 2 | 2 | 0x0003 | Reply code: Reply to import. | +-----------+--------+------------+---------------------------------------------------+
@@ -254,158 +283,151 @@ OP_REP_IMPORT: | 0x13E | 1 | | bNumInterfaces | +-----------+--------+------------+---------------------------------------------------+ -USBIP_CMD_SUBMIT: - Submit an URB +The following four commands have a common basic header called +'usbip_header_basic', and their headers, called 'usbip_header' (before URB +payload), have the same length, therefore paddings are needed. -+-----------+--------+------------+---------------------------------------------------+ -| Offset | Length | Value | Description | -+===========+========+============+===================================================+ -| 0 | 4 | 0x00000001 | command: Submit an URB | -+-----------+--------+------------+---------------------------------------------------+ -| 4 | 4 | | seqnum: the sequence number of the URB to submit | -+-----------+--------+------------+---------------------------------------------------+ -| 8 | 4 | | devid | -+-----------+--------+------------+---------------------------------------------------+ -| 0xC | 4 | | direction: | -| | | | | -| | | | - 0: USBIP_DIR_OUT | -| | | | - 1: USBIP_DIR_IN | -+-----------+--------+------------+---------------------------------------------------+ -| 0x10 | 4 | | ep: endpoint number, possible values are: 0...15 | -+-----------+--------+------------+---------------------------------------------------+ -| 0x14 | 4 | | transfer_flags: possible values depend on the | -| | | | URB transfer type, see below | -+-----------+--------+------------+---------------------------------------------------+ -| 0x18 | 4 | | transfer_buffer_length | -+-----------+--------+------------+---------------------------------------------------+ -| 0x1C | 4 | | start_frame: specify the selected frame to | -| | | | transmit an ISO frame, ignored if URB_ISO_ASAP | -| | | | is specified at transfer_flags | -+-----------+--------+------------+---------------------------------------------------+ -| 0x20 | 4 | | number_of_packets: number of ISO packets | -+-----------+--------+------------+---------------------------------------------------+ -| 0x24 | 4 | | interval: maximum time for the request on the | -| | | | server-side host controller | -+-----------+--------+------------+---------------------------------------------------+ -| 0x28 | 8 | | setup: data bytes for USB setup, filled with | -| | | | zeros if not used | -+-----------+--------+------------+---------------------------------------------------+ -| 0x30 | | | URB data. For ISO transfers the padding between | -| | | | each ISO packets is not transmitted. | -+-----------+--------+------------+---------------------------------------------------+ +usbip_header_basic: ++-----------+--------+---------------------------------------------------+ +| Offset | Length | Description | ++===========+========+===================================================+ +| 0 | 4 | command | ++-----------+--------+---------------------------------------------------+ +| 4 | 4 | seqnum: sequential number that identifies requests| +| | | and corresponding responses; | +| | | incremented per connection | ++-----------+--------+---------------------------------------------------+ +| 8 | 4 | devid: specifies a remote USB device uniquely | +| | | instead of busnum and devnum; | +| | | for client (request), this value is | +| | | ((busnum << 16) | devnum); | +| | | for server (response), this shall be set to 0 | ++-----------+--------+---------------------------------------------------+ +| 0xC | 4 | direction: | +| | | | +| | | - 0: USBIP_DIR_OUT | +| | | - 1: USBIP_DIR_IN | +| | | | +| | | only used by client, for server this shall be 0 | ++-----------+--------+---------------------------------------------------+ +| 0x10 | 4 | ep: endpoint number | +| | | only used by client, for server this shall be 0; | +| | | for UNLINK, this shall be 0 | ++-----------+--------+---------------------------------------------------+ - +-------------------------+------------+---------+-----------+----------+-------------+ - | Allowed transfer_flags | value | control | interrupt | bulk | isochronous | - +=========================+============+=========+===========+==========+=============+ - | URB_SHORT_NOT_OK | 0x00000001 | only in | only in | only in | no | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_ISO_ASAP | 0x00000002 | no | no | no | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_NO_TRANSFER_DMA_MAP | 0x00000004 | yes | yes | yes | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_ZERO_PACKET | 0x00000040 | no | no | only out | no | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_NO_INTERRUPT | 0x00000080 | yes | yes | yes | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_FREE_BUFFER | 0x00000100 | yes | yes | yes | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_DIR_MASK | 0x00000200 | yes | yes | yes | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ +USBIP_CMD_SUBMIT: + Submit an URB ++-----------+--------+---------------------------------------------------+ +| Offset | Length | Description | ++===========+========+===================================================+ +| 0 | 20 | usbip_header_basic, 'command' shall be 0x00000001 | ++-----------+--------+---------------------------------------------------+ +| 0x14 | 4 | transfer_flags: possible values depend on the | +| | | URB transfer_flags, | +| | | but with URB_NO_TRANSFER_DMA_MAP masked | ++-----------+--------+---------------------------------------------------+ +| 0x18 | 4 | transfer_buffer_length: | +| | | use URB transfer_buffer_length | ++-----------+--------+---------------------------------------------------+ +| 0x1C | 4 | start_frame: use URB start_frame; | +| | | initial frame for ISO transfer; | +| | | shall be set to 0 if not ISO transfer | ++-----------+--------+---------------------------------------------------+ +| 0x20 | 4 | number_of_packets: number of ISO packets; | +| | | shall be set to 0xffffffff if not ISO transfer | ++-----------+--------+---------------------------------------------------+ +| 0x24 | 4 | interval: maximum time for the request on the | +| | | server-side host controller | ++-----------+--------+---------------------------------------------------+ +| 0x28 | 8 | setup: data bytes for USB setup, filled with | +| | | zeros if not used. | ++-----------+--------+---------------------------------------------------+ +| 0x30 | n | transfer_buffer. | +| | | If direction is USBIP_DIR_OUT then n equals | +| | | transfer_buffer_length; otherwise n equals 0. | +| | | For ISO transfers the padding between each ISO | +| | | packets is not transmitted. | ++-----------+--------+---------------------------------------------------+ +| 0x30+n | m | iso_packet_descriptor | ++-----------+--------+---------------------------------------------------+ USBIP_RET_SUBMIT: Reply for submitting an URB -+-----------+--------+------------+---------------------------------------------------+ -| Offset | Length | Value | Description | -+===========+========+============+===================================================+ -| 0 | 4 | 0x00000003 | command | -+-----------+--------+------------+---------------------------------------------------+ -| 4 | 4 | | seqnum: URB sequence number | -+-----------+--------+------------+---------------------------------------------------+ -| 8 | 4 | | devid | -+-----------+--------+------------+---------------------------------------------------+ -| 0xC | 4 | | direction: | -| | | | | -| | | | - 0: USBIP_DIR_OUT | -| | | | - 1: USBIP_DIR_IN | -+-----------+--------+------------+---------------------------------------------------+ -| 0x10 | 4 | | ep: endpoint number | -+-----------+--------+------------+---------------------------------------------------+ -| 0x14 | 4 | | status: zero for successful URB transaction, | -| | | | otherwise some kind of error happened. | -+-----------+--------+------------+---------------------------------------------------+ -| 0x18 | 4 | n | actual_length: number of URB data bytes | -+-----------+--------+------------+---------------------------------------------------+ -| 0x1C | 4 | | start_frame: for an ISO frame the actually | -| | | | selected frame for transmit. | -+-----------+--------+------------+---------------------------------------------------+ -| 0x20 | 4 | | number_of_packets | -+-----------+--------+------------+---------------------------------------------------+ -| 0x24 | 4 | | error_count | -+-----------+--------+------------+---------------------------------------------------+ -| 0x28 | 8 | | setup: data bytes for USB setup, filled with | -| | | | zeros if not used | -+-----------+--------+------------+---------------------------------------------------+ -| 0x30 | n | | URB data bytes. For ISO transfers the padding | -| | | | between each ISO packets is not transmitted. | -+-----------+--------+------------+---------------------------------------------------+ ++-----------+--------+---------------------------------------------------+ +| Offset | Length | Description | ++===========+========+===================================================+ +| 0 | 20 | usbip_header_basic, 'command' shall be 0x00000003 | ++-----------+--------+---------------------------------------------------+ +| 0x14 | 4 | status: zero for successful URB transaction, | +| | | otherwise some kind of error happened. | ++-----------+--------+---------------------------------------------------+ +| 0x18 | 4 | actual_length: number of URB data bytes; | +| | | use URB actual_length | ++-----------+--------+---------------------------------------------------+ +| 0x1C | 4 | start_frame: use URB start_frame; | +| | | initial frame for ISO transfer; | +| | | shall be set to 0 if not ISO transfer | ++-----------+--------+---------------------------------------------------+ +| 0x20 | 4 | number_of_packets: number of ISO packets; | +| | | shall be set to 0xffffffff if not ISO transfer | ++-----------+--------+---------------------------------------------------+ +| 0x24 | 4 | error_count | ++-----------+--------+---------------------------------------------------+ +| 0x28 | 8 | padding, shall be set to 0 | ++-----------+--------+---------------------------------------------------+ +| 0x30 | n | transfer_buffer. | +| | | If direction is USBIP_DIR_IN then n equals | +| | | actual_length; otherwise n equals 0. | +| | | For ISO transfers the padding between each ISO | +| | | packets is not transmitted. | ++-----------+--------+---------------------------------------------------+ +| 0x30+n | m | iso_packet_descriptor | ++-----------+--------+---------------------------------------------------+ USBIP_CMD_UNLINK: Unlink an URB -+-----------+--------+------------+---------------------------------------------------+ -| Offset | Length | Value | Description | -+===========+========+============+===================================================+ -| 0 | 4 | 0x00000002 | command: URB unlink command | -+-----------+--------+------------+---------------------------------------------------+ -| 4 | 4 | | seqnum: URB sequence number to unlink: | -| | | | | -| | | | FIXME: | -| | | | is this so? | -+-----------+--------+------------+---------------------------------------------------+ -| 8 | 4 | | devid | -+-----------+--------+------------+---------------------------------------------------+ -| 0xC | 4 | | direction: | -| | | | | -| | | | - 0: USBIP_DIR_OUT | -| | | | - 1: USBIP_DIR_IN | -+-----------+--------+------------+---------------------------------------------------+ -| 0x10 | 4 | | ep: endpoint number: zero | -+-----------+--------+------------+---------------------------------------------------+ -| 0x14 | 4 | | seqnum: the URB sequence number given previously | -| | | | at USBIP_CMD_SUBMIT.seqnum field | -+-----------+--------+------------+---------------------------------------------------+ -| 0x30 | n | | URB data bytes. For ISO transfers the padding | -| | | | between each ISO packets is not transmitted. | -+-----------+--------+------------+---------------------------------------------------+ ++-----------+--------+---------------------------------------------------+ +| Offset | Length | Description | ++===========+========+===================================================+ +| 0 | 20 | usbip_header_basic, 'command' shall be 0x00000002 | ++-----------+--------+---------------------------------------------------+ +| 0x14 | 4 | unlink_seqnum, of the SUBMIT request to unlink | ++-----------+--------+---------------------------------------------------+ +| 0x18 | 24 | padding, shall be set to 0 | ++-----------+--------+---------------------------------------------------+ USBIP_RET_UNLINK: Reply for URB unlink -+-----------+--------+------------+---------------------------------------------------+ -| Offset | Length | Value | Description | -+===========+========+============+===================================================+ -| 0 | 4 | 0x00000004 | command: reply for the URB unlink command | -+-----------+--------+------------+---------------------------------------------------+ -| 4 | 4 | | seqnum: the unlinked URB sequence number | -+-----------+--------+------------+---------------------------------------------------+ -| 8 | 4 | | devid | -+-----------+--------+------------+---------------------------------------------------+ -| 0xC | 4 | | direction: | -| | | | | -| | | | - 0: USBIP_DIR_OUT | -| | | | - 1: USBIP_DIR_IN | -+-----------+--------+------------+---------------------------------------------------+ -| 0x10 | 4 | | ep: endpoint number | -+-----------+--------+------------+---------------------------------------------------+ -| 0x14 | 4 | | status: This is the value contained in the | -| | | | urb->status in the URB completition handler. | -| | | | | -| | | | FIXME: | -| | | | a better explanation needed. | -+-----------+--------+------------+---------------------------------------------------+ -| 0x30 | n | | URB data bytes. For ISO transfers the padding | -| | | | between each ISO packets is not transmitted. | -+-----------+--------+------------+---------------------------------------------------+ ++-----------+--------+---------------------------------------------------+ +| Offset | Length | Description | ++===========+========+===================================================+ +| 0 | 20 | usbip_header_basic, 'command' shall be 0x00000004 | ++-----------+--------+---------------------------------------------------+ +| 0x14 | 4 | status: This is similar to the status of | +| | | USBIP_RET_SUBMIT (share the same memory offset). | +| | | When UNLINK is successful, status is -ECONNRESET; | +| | | when USBIP_CMD_UNLINK is after USBIP_RET_SUBMIT | +| | | status is 0 | ++-----------+--------+---------------------------------------------------+ +| 0x18 | 24 | padding, shall be set to 0 | ++-----------+--------+---------------------------------------------------+ + +EXAMPLE +======= + + The following data is captured from wire with Human Interface Devices (HID) + payload + +:: + + CmdIntrIN: 00000001 00000d05 0001000f 00000001 00000001 00000200 00000040 ffffffff 00000000 00000004 00000000 00000000 + CmdIntrOUT: 00000001 00000d06 0001000f 00000000 00000001 00000000 00000040 ffffffff 00000000 00000004 00000000 00000000 + ffffffff860008a784ce5ae212376300000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 + RetIntrOut: 00000003 00000d06 00000000 00000000 00000000 00000000 00000040 ffffffff 00000000 00000000 00000000 00000000 + RetIntrIn: 00000003 00000d05 00000000 00000000 00000000 00000000 00000040 ffffffff 00000000 00000000 00000000 00000000 + ffffffff860011a784ce5ae2123763612891b1020100000400000000000000000000000000000000000000000000000000000000000000000000000000000000
Signature · 1 line
2.30.1
Shuah Khan
maintainerQuoted 52 lines · Hongren Zheng (Zenithal)
The old document for usbip protocol is misleading and hard to read:
* Some fields in header are incorrect
* Explanation of some fields are unclear or even wrong
* Padding of header (namely all headers have the same length) is not explicitly pointed out, which is crucial for stream protocol like TCPMajor changes:
* Document the correct field as described in the codebase.
* Document the padding in usbip headers. This is crucial for TCP stream hence these padding should be explicitly point out. In code these padding are implemented by a union of all headers.
* Fix two FIXME related to usbip unlink and Document the behavior of unlink in different situation.
* Clarify some field with more accurate explanation, like those fields associated with URB. Some constraints are extracted from code.
* Delete specifictransfer_flagdoc in usbip as it should be documented by the URB part.
* Add data captured from wire as exampleCo-developed-by Alexandre Demers <[email protected]>Reviewed-by Randy Dunlap <[email protected]>Signed-off-by Hongren Zheng <[email protected]>--- Documentation/usb/usbip_protocol.rst | 320 ++++++++++++++------------- 1 file changed, 171 insertions(+), 149 deletions(-)PATCH v2:
Some changes suggested by a previous patch in
https://lore.kernel.org/linux-usb
/[email protected]/
is adopted in this patch.
* Fix Typo: duplicated 'the' in 'the following 4 field'
* Fix incorrect field: inOP_REQ_DEVLIST, the second dev starts with field 'path', not 'busid'PATCH v3:
Suggested by
https://lore.kernel.org/linux-doc/YE8Oan2BmSuKR4%[email protected]/
* Remove date and changelog in doc as these are tracked in git history
* Remove 'mistake alert' as all data fields are documented properly now. However, docs on possible values for some field shall be added in the futurePATCH v4:
Suggested by https://lore.kernel.org/linux-doc
/[email protected]/
* Add punctuations for readability
* Move patch changelog after the marker line
* Remove nickname in signed-off-by line
Quoted 4 lines
PATCH v5:
* Instead of co-developed-by, use reviewed-by
for Randy Dunlap
Hi Hongren Zheng,
Thanks for the patch. The document updates are very much needed. I will review and give you comments.
Please wait for a couple of days before sending another version. Makes it easier for you an your reviewers.
I started reviewing patch v3 and I will switch to v5 now and send you comments.
thanks,
-- Shuah
Shuah Khan
maintainerQuoted 7 lines · Hongren Zheng (Zenithal)
The old document for usbip protocol is misleading and hard to read:
* Some fields in header are incorrect
* Explanation of some fields are unclear or even wrong
* Padding of header (namely all headers have the same length) is not explicitly pointed out, which is crucial for stream protocol like TCP
Quoted 12 lines
Major changes:
* Document the correct field as described in the codebase.
* Document the padding in usbip headers. This is crucial for TCP stream hence these padding should be explicitly point out. In code these padding are implemented by a union of all headers.
* Fix two FIXME related to usbip unlink and Document the behavior of unlink in different situation.
* Clarify some field with more accurate explanation, like those fields associated with URB. Some constraints are extracted from code.
* Delete specifictransfer_flagdoc in usbip as it should be documented by the URB part.
Why are we deleting this. What do you mean documented by URB part?
Quoted 42 lines
* Add data captured from wire as example
Co-developed-by Alexandre Demers <[email protected]>Reviewed-by Randy Dunlap <[email protected]>Signed-off-by Hongren Zheng <[email protected]>--- Documentation/usb/usbip_protocol.rst | 320 ++++++++++++++------------- 1 file changed, 171 insertions(+), 149 deletions(-)PATCH v2:
Some changes suggested by a previous patch in
https://lore.kernel.org/linux-usb
/[email protected]/
is adopted in this patch.
* Fix Typo: duplicated 'the' in 'the following 4 field'
* Fix incorrect field: inOP_REQ_DEVLIST, the second dev starts with field 'path', not 'busid'PATCH v3:
Suggested by
https://lore.kernel.org/linux-doc/YE8Oan2BmSuKR4%[email protected]/
* Remove date and changelog in doc as these are tracked in git history
* Remove 'mistake alert' as all data fields are documented properly now. However, docs on possible values for some field shall be added in the futurePATCH v4:
Suggested by https://lore.kernel.org/linux-doc
/[email protected]/
* Add punctuations for readability
* Move patch changelog after the marker line
* Remove nickname in signed-off-by linePATCH v5:
* Instead of co-developed-by, use reviewed-by
for Randy DunlapDocumentation/usb/usbip_protocol.rst +0
-0
Documentation/usb/usbip_protocol.rst line 5
Quoted 4 lines
Documentation/usb/usbip_protocol.rst +1
-0@@ -2,11 +2,11 @@ USB/IP protocol =============== > -PRELIMINARY DRAFT, MAY CONTAIN MISTAKES> -28 Jun 2011 +Architecture
Let's add doc version preserving the history.
Add Version 1 and date perhaps.
Documentation/usb/usbip_protocol.rst line 9
Quoted 5 lines
Documentation/usb/usbip_protocol.rst +2
-1+============ The USB/IP protocol follows a server/client architecture. The server exports the -USB devices and the clients imports them. The device driver for the exported +USB devices and the client imports them. The device driver for the exported
clients import them.
Documentation/usb/usbip_protocol.rst to transfer the URB traffic between the client and the server. The client may · line 42
Quoted 10 lines
Documentation/usb/usbip_protocol.rst +3
-0USB device runs on the client machine. The client may ask for the list of the exported USB devices. To get the list the@@ -37,6 +37,9 @@ to transfer the URB traffic between the client and the server. The client may send two types of packets: the USBIP_CMD_SUBMIT to submit an URB, and USBIP_CMD_UNLINK to unlink a previously submitted URB. The answers of the server may be USBIP_RET_SUBMIT and USBIP_RET_UNLINK respectively. +Note that after successful USBIP_RET_UNLINK, the unlinked URB request would not +have a corresponding USBIP_RET_UNLINK (this is explained in +drivers/usb/usbip/stub_rx.c).
This is not clear to me. Doesn't look correct. Where do you see this in drivers/usb/usbip/stub_rx.c?
Quoted 28 lines
Documentation/usb/usbip_protocol.rst +21
-0::@@ -85,16 +88,42 @@ server may be USBIP_RET_SUBMIT and USBIP_RET_UNLINK respectively. | . | | : | | | + | USBIP_CMD_SUBMIT(seqnum = p) | + | ----------------------------------------------> | + | | + | USBIP_CMD_UNLINK | + | (seqnum = p+1, unlink_seqnum = p) | + | ----------------------------------------------> | + | | + | USBIP_RET_UNLINK | + | (seqnum = p+1, status = -ECONNRESET) | + | <---------------------------------------------- | + | | + | Note: No USBIP_RET_SUBMIT(seqnum = p) | + | <--X---X---X---X---X---X---X---X---X---X---X--- | + | . | + | : | + | | + | USBIP_CMD_SUBMIT(seqnum = q) | + | ----------------------------------------------> | + | | + | USBIP_RET_SUBMIT(seqnum = q) | + | <---------------------------------------------- |
Documentation/usb/usbip_protocol.rst server may be USBIP_RET_SUBMIT and USBIP_RET_UNLINK respectively. · line 121
Quoted 10 lines
Documentation/usb/usbip_protocol.rst +3
-0+ | | | USBIP_CMD_UNLINK | + | (seqnum = q+1, unlink_seqnum = q) | | ----------------------------------------------> | | | | USBIP_RET_UNLINK | + | (seqnum = q+1, status = 0) | | <---------------------------------------------- | | |
I would do this differently. Let's add this as an expanded USBIP_CMD_UNLINK sequence with a separate heading below the current flow
Quoted 9 lines
Documentation/usb/usbip_protocol.rst +2
-0The fields are in network (big endian) byte order meaning that the most significant byte (MSB) is stored at the lowest address. +Message Format +============== OP_REQ_DEVLIST: Retrieve the list of exported USB devices.
Documentation/usb/usbip_protocol.rst OP_REQ_DEVLIST: · line 135
Quoted 6 lines
Documentation/usb/usbip_protocol.rst +1
-1@@ -102,7 +131,7 @@ OP_REQ_DEVLIST: +-----------+--------+------------+---------------------------------------------------+ | Offset | Length | Value | Description | +===========+========+============+===================================================+ -| 0 | 2 | 0x0100 | Binary-coded decimal USBIP version number: v1.0.0 | +| 0 | 2 | 0x0111 | Binary-coded decimal USBIP version number: v1.1.1 | +-----------+--------+------------+---------------------------------------------------+
Let's make this vx.x.x and specify current version number at the top. Saves us doc updates as we change version number - one location change as opposed to the entire document
Quoted 341 lines
Documentation/usb/usbip_protocol.rst +138
-145| 2 | 2 | 0x8005 | Command code: Retrieve the list of exported USB | | | | | devices. |@@ -116,7 +145,7 @@ OP_REP_DEVLIST: +-----------+--------+------------+---------------------------------------------------+ | Offset | Length | Value | Description | +===========+========+============+===================================================+ -| 0 | 2 | 0x0100 | Binary-coded decimal USBIP version number: v1.0.0.| +| 0 | 2 | 0x0111 | Binary-coded decimal USBIP version number: v1.1.1 | +-----------+--------+------------+---------------------------------------------------+ | 2 | 2 | 0x0005 | Reply code: The list of exported USB devices. | +-----------+--------+------------+---------------------------------------------------+@@ -165,8 +194,8 @@ OP_REP_DEVLIST: | 0x143 | 1 | | bNumInterfaces | +-----------+--------+------------+---------------------------------------------------+ | 0x144 | | m_0 | From now on each interface is described, all | -| | | | together bNumInterfaces times, with the | -| | | | the following 4 fields: | +| | | | together bNumInterfaces times, with the following | +| | | | 4 fields: | +-----------+--------+------------+---------------------------------------------------+ | | 1 | | bInterfaceClass | +-----------+--------+------------+---------------------------------------------------+@@ -177,7 +206,7 @@ OP_REP_DEVLIST: | 0x147 | 1 | | padding byte for alignment, shall be set to zero | +-----------+--------+------------+---------------------------------------------------+ | 0xC + | | | The second exported USB device starts at i=1 | -| i*0x138 + | | | with the busid field. | +| i*0x138 + | | | with the path field. | | m_(i-1)*4 | | | | +-----------+--------+------------+---------------------------------------------------+@@ -187,7 +216,7 @@ OP_REQ_IMPORT: +-----------+--------+------------+---------------------------------------------------+ | Offset | Length | Value | Description | +===========+========+============+===================================================+ -| 0 | 2 | 0x0100 | Binary-coded decimal USBIP version number: v1.0.0 | +| 0 | 2 | 0x0111 | Binary-coded decimal USBIP version number: v1.1.1 | +-----------+--------+------------+---------------------------------------------------+ | 2 | 2 | 0x8003 | Command code: import a remote USB device. | +-----------+--------+------------+---------------------------------------------------+@@ -206,7 +235,7 @@ OP_REP_IMPORT: +-----------+--------+------------+---------------------------------------------------+ | Offset | Length | Value | Description | +===========+========+============+===================================================+ -| 0 | 2 | 0x0100 | Binary-coded decimal USBIP version number: v1.0.0 | +| 0 | 2 | 0x0111 | Binary-coded decimal USBIP version number: v1.1.1 | +-----------+--------+------------+---------------------------------------------------+ | 2 | 2 | 0x0003 | Reply code: Reply to import. | +-----------+--------+------------+---------------------------------------------------+@@ -254,158 +283,151 @@ OP_REP_IMPORT: | 0x13E | 1 | | bNumInterfaces | +-----------+--------+------------+---------------------------------------------------+ -USBIP_CMD_SUBMIT: - Submit an URB +The following four commands have a common basic header called +'usbip_header_basic', and their headers, called 'usbip_header' (before URB +payload), have the same length, therefore paddings are needed. -+-----------+--------+------------+---------------------------------------------------+ -| Offset | Length | Value | Description | -+===========+========+============+===================================================+ -| 0 | 4 | 0x00000001 | command: Submit an URB | -+-----------+--------+------------+---------------------------------------------------+ -| 4 | 4 | | seqnum: the sequence number of the URB to submit | -+-----------+--------+------------+---------------------------------------------------+ -| 8 | 4 | | devid | -+-----------+--------+------------+---------------------------------------------------+ -| 0xC | 4 | | direction: | -| | | | | -| | | | - 0: USBIP_DIR_OUT | -| | | | - 1: USBIP_DIR_IN | -+-----------+--------+------------+---------------------------------------------------+ -| 0x10 | 4 | | ep: endpoint number, possible values are: 0...15 | -+-----------+--------+------------+---------------------------------------------------+ -| 0x14 | 4 | | transfer_flags: possible values depend on the | -| | | | URB transfer type, see below | -+-----------+--------+------------+---------------------------------------------------+ -| 0x18 | 4 | | transfer_buffer_length | -+-----------+--------+------------+---------------------------------------------------+ -| 0x1C | 4 | | start_frame: specify the selected frame to | -| | | | transmit an ISO frame, ignored if URB_ISO_ASAP | -| | | | is specified at transfer_flags | -+-----------+--------+------------+---------------------------------------------------+ -| 0x20 | 4 | | number_of_packets: number of ISO packets | -+-----------+--------+------------+---------------------------------------------------+ -| 0x24 | 4 | | interval: maximum time for the request on the | -| | | | server-side host controller | -+-----------+--------+------------+---------------------------------------------------+ -| 0x28 | 8 | | setup: data bytes for USB setup, filled with | -| | | | zeros if not used | -+-----------+--------+------------+---------------------------------------------------+ -| 0x30 | | | URB data. For ISO transfers the padding between | -| | | | each ISO packets is not transmitted. | -+-----------+--------+------------+---------------------------------------------------+ +usbip_header_basic: ++-----------+--------+---------------------------------------------------+ +| Offset | Length | Description | ++===========+========+===================================================+ +| 0 | 4 | command | ++-----------+--------+---------------------------------------------------+ +| 4 | 4 | seqnum: sequential number that identifies requests| +| | | and corresponding responses; | +| | | incremented per connection | ++-----------+--------+---------------------------------------------------+ +| 8 | 4 | devid: specifies a remote USB device uniquely | +| | | instead of busnum and devnum; | +| | | for client (request), this value is | +| | | ((busnum << 16) | devnum); | +| | | for server (response), this shall be set to 0 | ++-----------+--------+---------------------------------------------------+ +| 0xC | 4 | direction: | +| | | | +| | | - 0: USBIP_DIR_OUT | +| | | - 1: USBIP_DIR_IN | +| | | | +| | | only used by client, for server this shall be 0 | ++-----------+--------+---------------------------------------------------+ +| 0x10 | 4 | ep: endpoint number | +| | | only used by client, for server this shall be 0; | +| | | for UNLINK, this shall be 0 | ++-----------+--------+---------------------------------------------------+ - +-------------------------+------------+---------+-----------+----------+-------------+ - | Allowed transfer_flags | value | control | interrupt | bulk | isochronous | - +=========================+============+=========+===========+==========+=============+ - | URB_SHORT_NOT_OK | 0x00000001 | only in | only in | only in | no | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_ISO_ASAP | 0x00000002 | no | no | no | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_NO_TRANSFER_DMA_MAP | 0x00000004 | yes | yes | yes | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_ZERO_PACKET | 0x00000040 | no | no | only out | no | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_NO_INTERRUPT | 0x00000080 | yes | yes | yes | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_FREE_BUFFER | 0x00000100 | yes | yes | yes | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_DIR_MASK | 0x00000200 | yes | yes | yes | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ +USBIP_CMD_SUBMIT: + Submit an URB ++-----------+--------+---------------------------------------------------+ +| Offset | Length | Description | ++===========+========+===================================================+ +| 0 | 20 | usbip_header_basic, 'command' shall be 0x00000001 | ++-----------+--------+---------------------------------------------------+ +| 0x14 | 4 | transfer_flags: possible values depend on the | +| | | URB transfer_flags, | +| | | but with URB_NO_TRANSFER_DMA_MAP masked | ++-----------+--------+---------------------------------------------------+ +| 0x18 | 4 | transfer_buffer_length: | +| | | use URB transfer_buffer_length | ++-----------+--------+---------------------------------------------------+ +| 0x1C | 4 | start_frame: use URB start_frame; | +| | | initial frame for ISO transfer; | +| | | shall be set to 0 if not ISO transfer | ++-----------+--------+---------------------------------------------------+ +| 0x20 | 4 | number_of_packets: number of ISO packets; | +| | | shall be set to 0xffffffff if not ISO transfer | ++-----------+--------+---------------------------------------------------+ +| 0x24 | 4 | interval: maximum time for the request on the | +| | | server-side host controller | ++-----------+--------+---------------------------------------------------+ +| 0x28 | 8 | setup: data bytes for USB setup, filled with | +| | | zeros if not used. | ++-----------+--------+---------------------------------------------------+ +| 0x30 | n | transfer_buffer. | +| | | If direction is USBIP_DIR_OUT then n equals | +| | | transfer_buffer_length; otherwise n equals 0. | +| | | For ISO transfers the padding between each ISO | +| | | packets is not transmitted. | ++-----------+--------+---------------------------------------------------+ +| 0x30+n | m | iso_packet_descriptor | ++-----------+--------+---------------------------------------------------+ USBIP_RET_SUBMIT: Reply for submitting an URB -+-----------+--------+------------+---------------------------------------------------+ -| Offset | Length | Value | Description | -+===========+========+============+===================================================+ -| 0 | 4 | 0x00000003 | command | -+-----------+--------+------------+---------------------------------------------------+ -| 4 | 4 | | seqnum: URB sequence number | -+-----------+--------+------------+---------------------------------------------------+ -| 8 | 4 | | devid | -+-----------+--------+------------+---------------------------------------------------+ -| 0xC | 4 | | direction: | -| | | | | -| | | | - 0: USBIP_DIR_OUT | -| | | | - 1: USBIP_DIR_IN | -+-----------+--------+------------+---------------------------------------------------+ -| 0x10 | 4 | | ep: endpoint number | -+-----------+--------+------------+---------------------------------------------------+ -| 0x14 | 4 | | status: zero for successful URB transaction, | -| | | | otherwise some kind of error happened. | -+-----------+--------+------------+---------------------------------------------------+ -| 0x18 | 4 | n | actual_length: number of URB data bytes | -+-----------+--------+------------+---------------------------------------------------+ -| 0x1C | 4 | | start_frame: for an ISO frame the actually | -| | | | selected frame for transmit. | -+-----------+--------+------------+---------------------------------------------------+ -| 0x20 | 4 | | number_of_packets | -+-----------+--------+------------+---------------------------------------------------+ -| 0x24 | 4 | | error_count | -+-----------+--------+------------+---------------------------------------------------+ -| 0x28 | 8 | | setup: data bytes for USB setup, filled with | -| | | | zeros if not used | -+-----------+--------+------------+---------------------------------------------------+ -| 0x30 | n | | URB data bytes. For ISO transfers the padding | -| | | | between each ISO packets is not transmitted. | -+-----------+--------+------------+---------------------------------------------------+ ++-----------+--------+---------------------------------------------------+ +| Offset | Length | Description | ++===========+========+===================================================+ +| 0 | 20 | usbip_header_basic, 'command' shall be 0x00000003 | ++-----------+--------+---------------------------------------------------+ +| 0x14 | 4 | status: zero for successful URB transaction, | +| | | otherwise some kind of error happened. | ++-----------+--------+---------------------------------------------------+ +| 0x18 | 4 | actual_length: number of URB data bytes; | +| | | use URB actual_length | ++-----------+--------+---------------------------------------------------+ +| 0x1C | 4 | start_frame: use URB start_frame; | +| | | initial frame for ISO transfer; | +| | | shall be set to 0 if not ISO transfer | ++-----------+--------+---------------------------------------------------+ +| 0x20 | 4 | number_of_packets: number of ISO packets; | +| | | shall be set to 0xffffffff if not ISO transfer | ++-----------+--------+---------------------------------------------------+ +| 0x24 | 4 | error_count | ++-----------+--------+---------------------------------------------------+ +| 0x28 | 8 | padding, shall be set to 0 | ++-----------+--------+---------------------------------------------------+ +| 0x30 | n | transfer_buffer. | +| | | If direction is USBIP_DIR_IN then n equals | +| | | actual_length; otherwise n equals 0. | +| | | For ISO transfers the padding between each ISO | +| | | packets is not transmitted. | ++-----------+--------+---------------------------------------------------+ +| 0x30+n | m | iso_packet_descriptor | ++-----------+--------+---------------------------------------------------+ USBIP_CMD_UNLINK: Unlink an URB -+-----------+--------+------------+---------------------------------------------------+ -| Offset | Length | Value | Description | -+===========+========+============+===================================================+ -| 0 | 4 | 0x00000002 | command: URB unlink command | -+-----------+--------+------------+---------------------------------------------------+ -| 4 | 4 | | seqnum: URB sequence number to unlink: | -| | | | | -| | | | FIXME: | -| | | | is this so? | -+-----------+--------+------------+---------------------------------------------------+ -| 8 | 4 | | devid | -+-----------+--------+------------+---------------------------------------------------+ -| 0xC | 4 | | direction: | -| | | | | -| | | | - 0: USBIP_DIR_OUT | -| | | | - 1: USBIP_DIR_IN | -+-----------+--------+------------+---------------------------------------------------+ -| 0x10 | 4 | | ep: endpoint number: zero | -+-----------+--------+------------+---------------------------------------------------+ -| 0x14 | 4 | | seqnum: the URB sequence number given previously | -| | | | at USBIP_CMD_SUBMIT.seqnum field | -+-----------+--------+------------+---------------------------------------------------+ -| 0x30 | n | | URB data bytes. For ISO transfers the padding | -| | | | between each ISO packets is not transmitted. | -+-----------+--------+------------+---------------------------------------------------+ ++-----------+--------+---------------------------------------------------+ +| Offset | Length | Description | ++===========+========+===================================================+ +| 0 | 20 | usbip_header_basic, 'command' shall be 0x00000002 | ++-----------+--------+---------------------------------------------------+ +| 0x14 | 4 | unlink_seqnum, of the SUBMIT request to unlink | ++-----------+--------+---------------------------------------------------+ +| 0x18 | 24 | padding, shall be set to 0 | ++-----------+--------+---------------------------------------------------+ USBIP_RET_UNLINK: Reply for URB unlink -+-----------+--------+------------+---------------------------------------------------+ -| Offset | Length | Value | Description | -+===========+========+============+===================================================+ -| 0 | 4 | 0x00000004 | command: reply for the URB unlink command | -+-----------+--------+------------+---------------------------------------------------+ -| 4 | 4 | | seqnum: the unlinked URB sequence number | -+-----------+--------+------------+---------------------------------------------------+ -| 8 | 4 | | devid | -+-----------+--------+------------+---------------------------------------------------+ -| 0xC | 4 | | direction: | -| | | | | -| | | | - 0: USBIP_DIR_OUT | -| | | | - 1: USBIP_DIR_IN | -+-----------+--------+------------+---------------------------------------------------+ -| 0x10 | 4 | | ep: endpoint number | -+-----------+--------+------------+---------------------------------------------------+ -| 0x14 | 4 | | status: This is the value contained in the | -| | | | urb->status in the URB completition handler. | -| | | | | -| | | | FIXME: | -| | | | a better explanation needed. | -+-----------+--------+------------+---------------------------------------------------+ -| 0x30 | n | | URB data bytes. For ISO transfers the padding | -| | | | between each ISO packets is not transmitted. | -+-----------+--------+------------+---------------------------------------------------+ ++-----------+--------+---------------------------------------------------+ +| Offset | Length | Description | ++===========+========+===================================================+ +| 0 | 20 | usbip_header_basic, 'command' shall be 0x00000004 | ++-----------+--------+---------------------------------------------------+ +| 0x14 | 4 | status: This is similar to the status of | +| | | USBIP_RET_SUBMIT (share the same memory offset). | +| | | When UNLINK is successful, status is -ECONNRESET; | +| | | when USBIP_CMD_UNLINK is after USBIP_RET_SUBMIT | +| | | status is 0 | ++-----------+--------+---------------------------------------------------+ +| 0x18 | 24 | padding, shall be set to 0 | ++-----------+--------+---------------------------------------------------+ + +EXAMPLE +======= + + The following data is captured from wire with Human Interface Devices (HID) + payload + +:: + + CmdIntrIN: 00000001 00000d05 0001000f 00000001 00000001 00000200 00000040 ffffffff 00000000 00000004 00000000 00000000 + CmdIntrOUT: 00000001 00000d06 0001000f 00000000 00000001 00000000 00000040 ffffffff 00000000 00000004 00000000 00000000 + ffffffff860008a784ce5ae212376300000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 + RetIntrOut: 00000003 00000d06 00000000 00000000 00000000 00000000 00000040 ffffffff 00000000 00000000 00000000 00000000 + RetIntrIn: 00000003 00000d05 00000000 00000000 00000000 00000000 00000040 ffffffff 00000000 00000000 00000000 00000000 + ffffffff860011a784ce5ae2123763612891b1020100000400000000000000000000000000000000000000000000000000000000000000000000000000000000
Hongren Zheng (Zenithal)
reviewerQuoted 21 lines · Shuah Khan
Quoted 7 lines · Hongren Zheng (Zenithal)
The old document for usbip protocol is misleading and hard to read:
* Some fields in header are incorrect
* Explanation of some fields are unclear or even wrong
* Padding of header (namely all headers have the same length) is not explicitly pointed out, which is crucial for stream protocol like TCPQuoted 12 lines
Major changes:
* Document the correct field as described in the codebase.
* Document the padding in usbip headers. This is crucial for TCP stream hence these padding should be explicitly point out. In code these padding are implemented by a union of all headers.
* Fix two FIXME related to usbip unlink and Document the behavior of unlink in different situation.
* Clarify some field with more accurate explanation, like those fields associated with URB. Some constraints are extracted from code.
* Delete specifictransfer_flagdoc in usbip as it should be documented by the URB part.
Quoted 1 line
Why are we deleting this. What do you mean documented by URB part?
transfer_flag are actually defined by the URB struct,
refer to https://www.kernel.org/doc/html/latest/driver-api/usb/URB.html
and usbip headers just encapsulate this flag.
You may refer to usbip_pack_cmd_submit in /drivers/usb/usbip/usbip_common.c and notice that
the flag are just copied from one URB with a small tweak. (Note that this tweak is also documented below).
Hence the possible transfer flags for each transfer type should be explained by URB document, not USB/IP document. I think documenting them here is duplicated, hence I deleted them.
Quoted 38 lines
Quoted 38 lines
* Add data captured from wire as example
Co-developed-by Alexandre Demers <[email protected]>Reviewed-by Randy Dunlap <[email protected]>Signed-off-by Hongren Zheng <[email protected]>--- Documentation/usb/usbip_protocol.rst | 320 ++++++++++++++------------- 1 file changed, 171 insertions(+), 149 deletions(-)PATCH v2:
Some changes suggested by a previous patch in
https://lore.kernel.org/linux-usb
/[email protected]/
is adopted in this patch.
* Fix Typo: duplicated 'the' in 'the following 4 field'
* Fix incorrect field: inOP_REQ_DEVLIST, the second dev starts with field 'path', not 'busid'PATCH v3:
Suggested by
https://lore.kernel.org/linux-doc/YE8Oan2BmSuKR4%[email protected]/
* Remove date and changelog in doc as these are tracked in git history
* Remove 'mistake alert' as all data fields are documented properly now. However, docs on possible values for some field shall be added in the futurePATCH v4:
Suggested by https://lore.kernel.org/linux-doc
/[email protected]/
* Add punctuations for readability
* Move patch changelog after the marker line
* Remove nickname in signed-off-by linePATCH v5:
* Instead of co-developed-by, use reviewed-by
for Randy Dunlap
Quoted 12 lines
Documentation/usb/usbip_protocol.rst line 5
Quoted 9 lines
Documentation/usb/usbip_protocol.rst +1
-0@@ -2,11 +2,11 @@ USB/IP protocol =============== > -PRELIMINARY DRAFT, MAY CONTAIN MISTAKES> -28 Jun 2011 +ArchitectureLet's add doc version preserving the history.
Add Version 1 and date perhaps.
GKH suggested tracking version by git changlog, so I deleted these fields. Refer to
https://lore.kernel.org/linux-doc/YE8Oan2BmSuKR4%[email protected]/
Quoted 7 lines
Documentation/usb/usbip_protocol.rst line 9
Quoted 5 lines
Documentation/usb/usbip_protocol.rst +2
-1+============ The USB/IP protocol follows a server/client architecture. The server exports the -USB devices and the clients imports them. The device driver for the exported +USB devices and the client imports them. The device driver for the exportedclients import them.
Will be adopted in the next version of the PATCH
Quoted 13 lines
Documentation/usb/usbip_protocol.rst to transfer the URB traffic between the client and the server. The client may · line 42
Quoted 10 lines
Documentation/usb/usbip_protocol.rst +3
-0USB device runs on the client machine. The client may ask for the list of the exported USB devices. To get the list the@@ -37,6 +37,9 @@ to transfer the URB traffic between the client and the server. The client may send two types of packets: the USBIP_CMD_SUBMIT to submit an URB, and USBIP_CMD_UNLINK to unlink a previously submitted URB. The answers of the server may be USBIP_RET_SUBMIT and USBIP_RET_UNLINK respectively. +Note that after successful USBIP_RET_UNLINK, the unlinked URB request would not +have a corresponding USBIP_RET_UNLINK (this is explained in +drivers/usb/usbip/stub_rx.c).This is not clear to me. Doesn't look correct. Where do you see this in
drivers/usb/usbip/stub_rx.c?
Sorry that this is a typo. I meant "the unlinked URB request would not have a corresponding USBIP_RET_SUBMIT".
This is shown in the following flow by the "<-X--X--" line. This will be fixed in the next version of this PATCH.
The explanation is in the comments of function stub_recv_cmd_unlink. "The unlinking flag means that we are now **not** going to return the normal result pdu of a submission request, **but** going to return a result pdu of the unlink request"
This behavior is implemented by **replacing** the normal result pdu with a unlink result pdu. You may walk through this function to understand the behavior.
So should I add this function name in the document for clarity?
Quoted 32 lines
Quoted 32 lines
Documentation/usb/usbip_protocol.rst +23
-0::@@ -85,16 +88,42 @@ server may be USBIP_RET_SUBMIT and USBIP_RET_UNLINK respectively. | . | | : | | | + | USBIP_CMD_SUBMIT(seqnum = p) | + | ----------------------------------------------> | + | | + | USBIP_CMD_UNLINK | + | (seqnum = p+1, unlink_seqnum = p) | + | ----------------------------------------------> | + | | + | USBIP_RET_UNLINK | + | (seqnum = p+1, status = -ECONNRESET) | + | <---------------------------------------------- | + | | + | Note: No USBIP_RET_SUBMIT(seqnum = p) | + | <--X---X---X---X---X---X---X---X---X---X---X--- | + | . | + | : | + | | + | USBIP_CMD_SUBMIT(seqnum = q) | + | ----------------------------------------------> | + | | + | USBIP_RET_SUBMIT(seqnum = q) | + | <---------------------------------------------- | + | | | USBIP_CMD_UNLINK | + | (seqnum = q+1, unlink_seqnum = q) | | ----------------------------------------------> | | |
Quoted 8 lines
Documentation/usb/usbip_protocol.rst server may be USBIP_RET_SUBMIT and USBIP_RET_UNLINK respectively. · line 120
Quoted 4 lines
Documentation/usb/usbip_protocol.rst +1
-0| USBIP_RET_UNLINK | + | (seqnum = q+1, status = 0) | | <---------------------------------------------- | | |I would do this differently. Let's add this as an expanded
USBIP_CMD_UNLINKsequence with a separate heading below the current flow
Currently we have two flows, one for device list and another for device import and URB transfer.
I think that UNLINK is a common command within the latter flow, namely SUBMIT and UNLINK are interweaved in the whole flow, and separating UNLINK from SUBMIT would cause logical separation as if they follows different flow.
I think what I have documented is the full use case for UNLINK, so I wonder what do you mean by "expanded sequence".
Quoted 10 lines
Quoted 10 lines
Documentation/usb/usbip_protocol.rst +2
-0The fields are in network (big endian) byte order meaning that the most significant byte (MSB) is stored at the lowest address. +Message Format +============== OP_REQ_DEVLIST: Retrieve the list of exported USB devices.@@ -102,7 +131,7 @@ OP_REQ_DEVLIST: +-----------+--------+------------+---------------------------------------------------+ | Offset | Length | Value | Description |
Quoted 8 lines
Documentation/usb/usbip_protocol.rst OP_REQ_DEVLIST: · line 135
Quoted 4 lines
Documentation/usb/usbip_protocol.rst +1
-1+===========+========+============+===================================================+ -| 0 | 2 | 0x0100 | Binary-coded decimal USBIP version number: v1.0.0 | +| 0 | 2 | 0x0111 | Binary-coded decimal USBIP version number: v1.1.1 | +-----------+--------+------------+---------------------------------------------------+Let's make this vx.x.x and specify current version number at the top. Saves us doc updates as we change version number - one location change as opposed to the entire document
Will be adopted in the next version of the PATCH.
A sidenote though, the version number has not changed since the release (out of staging) of usbip.
Quoted 321 lines
Quoted 321 lines
Documentation/usb/usbip_protocol.rst +131
-145| 2 | 2 | 0x8005 | Command code: Retrieve the list of exported USB | | | | | devices. |@@ -116,7 +145,7 @@ OP_REP_DEVLIST: +-----------+--------+------------+---------------------------------------------------+ | Offset | Length | Value | Description | +===========+========+============+===================================================+ -| 0 | 2 | 0x0100 | Binary-coded decimal USBIP version number: v1.0.0.| +| 0 | 2 | 0x0111 | Binary-coded decimal USBIP version number: v1.1.1 | +-----------+--------+------------+---------------------------------------------------+ | 2 | 2 | 0x0005 | Reply code: The list of exported USB devices. | +-----------+--------+------------+---------------------------------------------------+@@ -165,8 +194,8 @@ OP_REP_DEVLIST: | 0x143 | 1 | | bNumInterfaces | +-----------+--------+------------+---------------------------------------------------+ | 0x144 | | m_0 | From now on each interface is described, all | -| | | | together bNumInterfaces times, with the | -| | | | the following 4 fields: | +| | | | together bNumInterfaces times, with the following | +| | | | 4 fields: | +-----------+--------+------------+---------------------------------------------------+ | | 1 | | bInterfaceClass | +-----------+--------+------------+---------------------------------------------------+@@ -177,7 +206,7 @@ OP_REP_DEVLIST: | 0x147 | 1 | | padding byte for alignment, shall be set to zero | +-----------+--------+------------+---------------------------------------------------+ | 0xC + | | | The second exported USB device starts at i=1 | -| i*0x138 + | | | with the busid field. | +| i*0x138 + | | | with the path field. | | m_(i-1)*4 | | | | +-----------+--------+------------+---------------------------------------------------+@@ -187,7 +216,7 @@ OP_REQ_IMPORT: +-----------+--------+------------+---------------------------------------------------+ | Offset | Length | Value | Description | +===========+========+============+===================================================+ -| 0 | 2 | 0x0100 | Binary-coded decimal USBIP version number: v1.0.0 | +| 0 | 2 | 0x0111 | Binary-coded decimal USBIP version number: v1.1.1 | +-----------+--------+------------+---------------------------------------------------+ | 2 | 2 | 0x8003 | Command code: import a remote USB device. | +-----------+--------+------------+---------------------------------------------------+@@ -206,7 +235,7 @@ OP_REP_IMPORT: +-----------+--------+------------+---------------------------------------------------+ | Offset | Length | Value | Description | +===========+========+============+===================================================+ -| 0 | 2 | 0x0100 | Binary-coded decimal USBIP version number: v1.0.0 | +| 0 | 2 | 0x0111 | Binary-coded decimal USBIP version number: v1.1.1 | +-----------+--------+------------+---------------------------------------------------+ | 2 | 2 | 0x0003 | Reply code: Reply to import. | +-----------+--------+------------+---------------------------------------------------+@@ -254,158 +283,151 @@ OP_REP_IMPORT: | 0x13E | 1 | | bNumInterfaces | +-----------+--------+------------+---------------------------------------------------+ -USBIP_CMD_SUBMIT: - Submit an URB +The following four commands have a common basic header called +'usbip_header_basic', and their headers, called 'usbip_header' (before URB +payload), have the same length, therefore paddings are needed. -+-----------+--------+------------+---------------------------------------------------+ -| Offset | Length | Value | Description | -+===========+========+============+===================================================+ -| 0 | 4 | 0x00000001 | command: Submit an URB | -+-----------+--------+------------+---------------------------------------------------+ -| 4 | 4 | | seqnum: the sequence number of the URB to submit | -+-----------+--------+------------+---------------------------------------------------+ -| 8 | 4 | | devid | -+-----------+--------+------------+---------------------------------------------------+ -| 0xC | 4 | | direction: | -| | | | | -| | | | - 0: USBIP_DIR_OUT | -| | | | - 1: USBIP_DIR_IN | -+-----------+--------+------------+---------------------------------------------------+ -| 0x10 | 4 | | ep: endpoint number, possible values are: 0...15 | -+-----------+--------+------------+---------------------------------------------------+ -| 0x14 | 4 | | transfer_flags: possible values depend on the | -| | | | URB transfer type, see below | -+-----------+--------+------------+---------------------------------------------------+ -| 0x18 | 4 | | transfer_buffer_length | -+-----------+--------+------------+---------------------------------------------------+ -| 0x1C | 4 | | start_frame: specify the selected frame to | -| | | | transmit an ISO frame, ignored if URB_ISO_ASAP | -| | | | is specified at transfer_flags | -+-----------+--------+------------+---------------------------------------------------+ -| 0x20 | 4 | | number_of_packets: number of ISO packets | -+-----------+--------+------------+---------------------------------------------------+ -| 0x24 | 4 | | interval: maximum time for the request on the | -| | | | server-side host controller | -+-----------+--------+------------+---------------------------------------------------+ -| 0x28 | 8 | | setup: data bytes for USB setup, filled with | -| | | | zeros if not used | -+-----------+--------+------------+---------------------------------------------------+ -| 0x30 | | | URB data. For ISO transfers the padding between | -| | | | each ISO packets is not transmitted. | -+-----------+--------+------------+---------------------------------------------------+ +usbip_header_basic: ++-----------+--------+---------------------------------------------------+ +| Offset | Length | Description | ++===========+========+===================================================+ +| 0 | 4 | command | ++-----------+--------+---------------------------------------------------+ +| 4 | 4 | seqnum: sequential number that identifies requests| +| | | and corresponding responses; | +| | | incremented per connection | ++-----------+--------+---------------------------------------------------+ +| 8 | 4 | devid: specifies a remote USB device uniquely | +| | | instead of busnum and devnum; | +| | | for client (request), this value is | +| | | ((busnum << 16) | devnum); | +| | | for server (response), this shall be set to 0 | ++-----------+--------+---------------------------------------------------+ +| 0xC | 4 | direction: | +| | | | +| | | - 0: USBIP_DIR_OUT | +| | | - 1: USBIP_DIR_IN | +| | | | +| | | only used by client, for server this shall be 0 | ++-----------+--------+---------------------------------------------------+ +| 0x10 | 4 | ep: endpoint number | +| | | only used by client, for server this shall be 0; | +| | | for UNLINK, this shall be 0 | ++-----------+--------+---------------------------------------------------+ - +-------------------------+------------+---------+-----------+----------+-------------+ - | Allowed transfer_flags | value | control | interrupt | bulk | isochronous | - +=========================+============+=========+===========+==========+=============+ - | URB_SHORT_NOT_OK | 0x00000001 | only in | only in | only in | no | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_ISO_ASAP | 0x00000002 | no | no | no | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_NO_TRANSFER_DMA_MAP | 0x00000004 | yes | yes | yes | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_ZERO_PACKET | 0x00000040 | no | no | only out | no | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_NO_INTERRUPT | 0x00000080 | yes | yes | yes | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_FREE_BUFFER | 0x00000100 | yes | yes | yes | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_DIR_MASK | 0x00000200 | yes | yes | yes | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ +USBIP_CMD_SUBMIT: + Submit an URB ++-----------+--------+---------------------------------------------------+ +| Offset | Length | Description | ++===========+========+===================================================+ +| 0 | 20 | usbip_header_basic, 'command' shall be 0x00000001 | ++-----------+--------+---------------------------------------------------+ +| 0x14 | 4 | transfer_flags: possible values depend on the | +| | | URB transfer_flags, | +| | | but with URB_NO_TRANSFER_DMA_MAP masked | ++-----------+--------+---------------------------------------------------+ +| 0x18 | 4 | transfer_buffer_length: | +| | | use URB transfer_buffer_length | ++-----------+--------+---------------------------------------------------+ +| 0x1C | 4 | start_frame: use URB start_frame; | +| | | initial frame for ISO transfer; | +| | | shall be set to 0 if not ISO transfer | ++-----------+--------+---------------------------------------------------+ +| 0x20 | 4 | number_of_packets: number of ISO packets; | +| | | shall be set to 0xffffffff if not ISO transfer | ++-----------+--------+---------------------------------------------------+ +| 0x24 | 4 | interval: maximum time for the request on the | +| | | server-side host controller | ++-----------+--------+---------------------------------------------------+ +| 0x28 | 8 | setup: data bytes for USB setup, filled with | +| | | zeros if not used. | ++-----------+--------+---------------------------------------------------+ +| 0x30 | n | transfer_buffer. | +| | | If direction is USBIP_DIR_OUT then n equals | +| | | transfer_buffer_length; otherwise n equals 0. | +| | | For ISO transfers the padding between each ISO | +| | | packets is not transmitted. | ++-----------+--------+---------------------------------------------------+ +| 0x30+n | m | iso_packet_descriptor | ++-----------+--------+---------------------------------------------------+ USBIP_RET_SUBMIT: Reply for submitting an URB -+-----------+--------+------------+---------------------------------------------------+ -| Offset | Length | Value | Description | -+===========+========+============+===================================================+ -| 0 | 4 | 0x00000003 | command | -+-----------+--------+------------+---------------------------------------------------+ -| 4 | 4 | | seqnum: URB sequence number | -+-----------+--------+------------+---------------------------------------------------+ -| 8 | 4 | | devid | -+-----------+--------+------------+---------------------------------------------------+ -| 0xC | 4 | | direction: | -| | | | | -| | | | - 0: USBIP_DIR_OUT | -| | | | - 1: USBIP_DIR_IN | -+-----------+--------+------------+---------------------------------------------------+ -| 0x10 | 4 | | ep: endpoint number | -+-----------+--------+------------+---------------------------------------------------+ -| 0x14 | 4 | | status: zero for successful URB transaction, | -| | | | otherwise some kind of error happened. | -+-----------+--------+------------+---------------------------------------------------+ -| 0x18 | 4 | n | actual_length: number of URB data bytes | -+-----------+--------+------------+---------------------------------------------------+ -| 0x1C | 4 | | start_frame: for an ISO frame the actually | -| | | | selected frame for transmit. | -+-----------+--------+------------+---------------------------------------------------+ -| 0x20 | 4 | | number_of_packets | -+-----------+--------+------------+---------------------------------------------------+ -| 0x24 | 4 | | error_count | -+-----------+--------+------------+---------------------------------------------------+ -| 0x28 | 8 | | setup: data bytes for USB setup, filled with | -| | | | zeros if not used | -+-----------+--------+------------+---------------------------------------------------+ -| 0x30 | n | | URB data bytes. For ISO transfers the padding | -| | | | between each ISO packets is not transmitted. | -+-----------+--------+------------+---------------------------------------------------+ ++-----------+--------+---------------------------------------------------+ +| Offset | Length | Description | ++===========+========+===================================================+ +| 0 | 20 | usbip_header_basic, 'command' shall be 0x00000003 | ++-----------+--------+---------------------------------------------------+ +| 0x14 | 4 | status: zero for successful URB transaction, | +| | | otherwise some kind of error happened. | ++-----------+--------+---------------------------------------------------+ +| 0x18 | 4 | actual_length: number of URB data bytes; | +| | | use URB actual_length | ++-----------+--------+---------------------------------------------------+ +| 0x1C | 4 | start_frame: use URB start_frame; | +| | | initial frame for ISO transfer; | +| | | shall be set to 0 if not ISO transfer | ++-----------+--------+---------------------------------------------------+ +| 0x20 | 4 | number_of_packets: number of ISO packets; | +| | | shall be set to 0xffffffff if not ISO transfer | ++-----------+--------+---------------------------------------------------+ +| 0x24 | 4 | error_count | ++-----------+--------+---------------------------------------------------+ +| 0x28 | 8 | padding, shall be set to 0 | ++-----------+--------+---------------------------------------------------+ +| 0x30 | n | transfer_buffer. | +| | | If direction is USBIP_DIR_IN then n equals | +| | | actual_length; otherwise n equals 0. | +| | | For ISO transfers the padding between each ISO | +| | | packets is not transmitted. | ++-----------+--------+---------------------------------------------------+ +| 0x30+n | m | iso_packet_descriptor | ++-----------+--------+---------------------------------------------------+ USBIP_CMD_UNLINK: Unlink an URB -+-----------+--------+------------+---------------------------------------------------+ -| Offset | Length | Value | Description | -+===========+========+============+===================================================+ -| 0 | 4 | 0x00000002 | command: URB unlink command | -+-----------+--------+------------+---------------------------------------------------+ -| 4 | 4 | | seqnum: URB sequence number to unlink: | -| | | | | -| | | | FIXME: | -| | | | is this so? | -+-----------+--------+------------+---------------------------------------------------+ -| 8 | 4 | | devid | -+-----------+--------+------------+---------------------------------------------------+ -| 0xC | 4 | | direction: | -| | | | | -| | | | - 0: USBIP_DIR_OUT | -| | | | - 1: USBIP_DIR_IN | -+-----------+--------+------------+---------------------------------------------------+ -| 0x10 | 4 | | ep: endpoint number: zero | -+-----------+--------+------------+---------------------------------------------------+ -| 0x14 | 4 | | seqnum: the URB sequence number given previously | -| | | | at USBIP_CMD_SUBMIT.seqnum field | -+-----------+--------+------------+---------------------------------------------------+ -| 0x30 | n | | URB data bytes. For ISO transfers the padding | -| | | | between each ISO packets is not transmitted. | -+-----------+--------+------------+---------------------------------------------------+ ++-----------+--------+---------------------------------------------------+ +| Offset | Length | Description | ++===========+========+===================================================+ +| 0 | 20 | usbip_header_basic, 'command' shall be 0x00000002 | ++-----------+--------+---------------------------------------------------+ +| 0x14 | 4 | unlink_seqnum, of the SUBMIT request to unlink | ++-----------+--------+---------------------------------------------------+ +| 0x18 | 24 | padding, shall be set to 0 | ++-----------+--------+---------------------------------------------------+ USBIP_RET_UNLINK: Reply for URB unlink -+-----------+--------+------------+---------------------------------------------------+ -| Offset | Length | Value | Description | -+===========+========+============+===================================================+ -| 0 | 4 | 0x00000004 | command: reply for the URB unlink command | -+-----------+--------+------------+---------------------------------------------------+ -| 4 | 4 | | seqnum: the unlinked URB sequence number | -+-----------+--------+------------+---------------------------------------------------+ -| 8 | 4 | | devid | -+-----------+--------+------------+---------------------------------------------------+ -| 0xC | 4 | | direction: | -| | | | | -| | | | - 0: USBIP_DIR_OUT | -| | | | - 1: USBIP_DIR_IN | -+-----------+--------+------------+---------------------------------------------------+ -| 0x10 | 4 | | ep: endpoint number | -+-----------+--------+------------+---------------------------------------------------+ -| 0x14 | 4 | | status: This is the value contained in the | -| | | | urb->status in the URB completition handler. | -| | | | | -| | | | FIXME: | -| | | | a better explanation needed. | -+-----------+--------+------------+---------------------------------------------------+ -| 0x30 | n | | URB data bytes. For ISO transfers the padding | -| | | | between each ISO packets is not transmitted. | -+-----------+--------+------------+---------------------------------------------------+ ++-----------+--------+---------------------------------------------------+ +| Offset | Length | Description | ++===========+========+===================================================+ +| 0 | 20 | usbip_header_basic, 'command' shall be 0x00000004 | ++-----------+--------+---------------------------------------------------+ +| 0x14 | 4 | status: This is similar to the status of | +| | | USBIP_RET_SUBMIT (share the same memory offset). | +| | | When UNLINK is successful, status is -ECONNRESET; | +| | | when USBIP_CMD_UNLINK is after USBIP_RET_SUBMIT | +| | | status is 0 | ++-----------+--------+---------------------------------------------------+ +| 0x18 | 24 | padding, shall be set to 0 | ++-----------+--------+---------------------------------------------------+ + +EXAMPLE +======= + + The following data is captured from wire with Human Interface Devices (HID) + payload + +::
Quoted 9 lines
Documentation/usb/usbip_protocol.rst OP_REP_IMPORT:
Quoted 8 lines
Documentation/usb/usbip_protocol.rst +7
-0+ + CmdIntrIN: 00000001 00000d05 0001000f 00000001 00000001 00000200 00000040 ffffffff 00000000 00000004 00000000 00000000 + CmdIntrOUT: 00000001 00000d06 0001000f 00000000 00000001 00000000 00000040 ffffffff 00000000 00000004 00000000 00000000 + ffffffff860008a784ce5ae212376300000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 + RetIntrOut: 00000003 00000d06 00000000 00000000 00000000 00000000 00000040 ffffffff 00000000 00000000 00000000 00000000 + RetIntrIn: 00000003 00000d05 00000000 00000000 00000000 00000000 00000040 ffffffff 00000000 00000000 00000000 00000000 + ffffffff860011a784ce5ae2123763612891b1020100000400000000000000000000000000000000000000000000000000000000000000000000000000000000
I will submit the next version of the PATCH after all the conversations above resolved.
Shuah Khan
maintainerQuoted 24 lines · Hongren Zheng (Zenithal)
Quoted 21 lines · Shuah Khan
Quoted 7 lines · Hongren Zheng (Zenithal)
The old document for usbip protocol is misleading and hard to read:
* Some fields in header are incorrect
* Explanation of some fields are unclear or even wrong
* Padding of header (namely all headers have the same length) is not explicitly pointed out, which is crucial for stream protocol like TCPQuoted 12 lines
Major changes:
* Document the correct field as described in the codebase.
* Document the padding in usbip headers. This is crucial for TCP stream hence these padding should be explicitly point out. In code these padding are implemented by a union of all headers.
* Fix two FIXME related to usbip unlink and Document the behavior of unlink in different situation.
* Clarify some field with more accurate explanation, like those fields associated with URB. Some constraints are extracted from code.
* Delete specifictransfer_flagdoc in usbip as it should be documented by the URB part.Quoted 1 line
Why are we deleting this. What do you mean documented by URB part?
Quoted 8 lines
transfer_flagare actually defined by the URB struct,
refer to https://www.kernel.org/doc/html/latest/driver-api/usb/URB.html
and usbip headers just encapsulate this flag.
You may refer tousbip_pack_cmd_submitin /drivers/usb/usbip/usbip_common.c and notice that
the flag are just copied from one URB with a small tweak. (Note that this tweak is also documented below).
It makes sense to not duplicate the information. Please add a reference to the URB doc here. Does the tweak require context? It would make sense to add the reference to URB doc and then call out the tweak.
Quoted 56 lines
Hence the possible transfer flags for each transfer type should be explained by URB document, not USB/IP document. I think documenting them here is duplicated, hence I deleted them.
Quoted 38 lines
Quoted 38 lines
* Add data captured from wire as example
Co-developed-by Alexandre Demers <[email protected]>Reviewed-by Randy Dunlap <[email protected]>Signed-off-by Hongren Zheng <[email protected]>--- Documentation/usb/usbip_protocol.rst | 320 ++++++++++++++------------- 1 file changed, 171 insertions(+), 149 deletions(-)PATCH v2:
Some changes suggested by a previous patch in
https://lore.kernel.org/linux-usb
/[email protected]/
is adopted in this patch.
* Fix Typo: duplicated 'the' in 'the following 4 field'
* Fix incorrect field: inOP_REQ_DEVLIST, the second dev starts with field 'path', not 'busid'PATCH v3:
Suggested by
https://lore.kernel.org/linux-doc/YE8Oan2BmSuKR4%[email protected]/
* Remove date and changelog in doc as these are tracked in git history
* Remove 'mistake alert' as all data fields are documented properly now. However, docs on possible values for some field shall be added in the futurePATCH v4:
Suggested by https://lore.kernel.org/linux-doc
/[email protected]/
* Add punctuations for readability
* Move patch changelog after the marker line
* Remove nickname in signed-off-by linePATCH v5:
* Instead of co-developed-by, use reviewed-by
for Randy DunlapQuoted 12 lines
Documentation/usb/usbip_protocol.rst line 5
Quoted 9 lines
Documentation/usb/usbip_protocol.rst +1
-0@@ -2,11 +2,11 @@ USB/IP protocol =============== > -PRELIMINARY DRAFT, MAY CONTAIN MISTAKES> -28 Jun 2011 +ArchitectureLet's add doc version preserving the history.
Add Version 1 and date perhaps.
Quoted 4 lines
GKH suggested tracking version by git changlog, so I deleted these fields. Refer to
https://lore.kernel.org/linux-doc/YE8Oan2BmSuKR4%[email protected]/
Ah okay. Please add the version change in the change log.
Quoted 10 lines
Quoted 7 lines
Documentation/usb/usbip_protocol.rst line 9
Quoted 5 lines
Documentation/usb/usbip_protocol.rst +2
-1+============ The USB/IP protocol follows a server/client architecture. The server exports the -USB devices and the clients imports them. The device driver for the exported +USB devices and the client imports them. The device driver for the exportedclients import them.
Will be adopted in the next version of the PATCH
While you are updating the doc, please change all instances of:
"connection towards the server"
to
"connection to the server"
Quoted 14 lines
Quoted 13 lines
Documentation/usb/usbip_protocol.rst to transfer the URB traffic between the client and the server. The client may · line 42
Quoted 10 lines
Documentation/usb/usbip_protocol.rst +3
-0USB device runs on the client machine. The client may ask for the list of the exported USB devices. To get the list the@@ -37,6 +37,9 @@ to transfer the URB traffic between the client and the server. The client may send two types of packets: the USBIP_CMD_SUBMIT to submit an URB, and USBIP_CMD_UNLINK to unlink a previously submitted URB. The answers of the server may be USBIP_RET_SUBMIT and USBIP_RET_UNLINK respectively. +Note that after successful USBIP_RET_UNLINK, the unlinked URB request would not +have a corresponding USBIP_RET_UNLINK (this is explained in +drivers/usb/usbip/stub_rx.c).This is not clear to me. Doesn't look correct. Where do you see this in
drivers/usb/usbip/stub_rx.c?
Quoted 5 lines
Sorry that this is a typo. I meant "the unlinked URB request would not have a corresponding
USBIP_RET_SUBMIT".
This is shown in the following flow by the "<-X--X--" line. This will be fixed in the next version of this PATCH.
Okay that makes sense.
Quoted 9 lines
The explanation is in the comments of function
stub_recv_cmd_unlink. "The unlinking flag means that we are now **not** going to return the normal result pdu of a submission request, **but** going to return a result pdu of the unlink request"
This behavior is implemented by **replacing** the normal result pdu with a unlink result pdu. You may walk through this function to understand the behavior.
So should I add this function name in the document for clarity?
Yes. Just confirming this is the one you are referring to. Yes. Please call out the function if you are referencing it here.
Quoted 48 lines
Quoted 32 lines
Quoted 32 lines
Documentation/usb/usbip_protocol.rst +23
-0::@@ -85,16 +88,42 @@ server may be USBIP_RET_SUBMIT and USBIP_RET_UNLINK respectively. | . | | : | | | + | USBIP_CMD_SUBMIT(seqnum = p) | + | ----------------------------------------------> | + | | + | USBIP_CMD_UNLINK | + | (seqnum = p+1, unlink_seqnum = p) | + | ----------------------------------------------> | + | | + | USBIP_RET_UNLINK | + | (seqnum = p+1, status = -ECONNRESET) | + | <---------------------------------------------- | + | | + | Note: No USBIP_RET_SUBMIT(seqnum = p) | + | <--X---X---X---X---X---X---X---X---X---X---X--- | + | . | + | : | + | | + | USBIP_CMD_SUBMIT(seqnum = q) | + | ----------------------------------------------> | + | | + | USBIP_RET_SUBMIT(seqnum = q) | + | <---------------------------------------------- | + | | | USBIP_CMD_UNLINK | + | (seqnum = q+1, unlink_seqnum = q) | | ----------------------------------------------> | | |Quoted 8 lines
Documentation/usb/usbip_protocol.rst server may be USBIP_RET_SUBMIT and USBIP_RET_UNLINK respectively. · line 120
Quoted 4 lines
Documentation/usb/usbip_protocol.rst +1
-0| USBIP_RET_UNLINK | + | (seqnum = q+1, status = 0) | | <---------------------------------------------- | | |I would do this differently. Let's add this as an expanded
USBIP_CMD_UNLINKsequence with a separate heading below the current flowCurrently we have two flows, one for device list and another for device import and URB transfer.
I think that UNLINK is a common command within the latter flow, namely SUBMIT and UNLINK are interweaved in the whole flow, and separating UNLINK from SUBMIT would cause logical separation as if they follows different flow.
Quoted 3 lines
I think what I have documented is the full use case for UNLINK, so I wonder what do you mean by "expanded sequence".
Let's expand this flow out separately. I think it will be easier to follow.
Quoted 19 lines
Quoted 10 lines
Quoted 10 lines
Documentation/usb/usbip_protocol.rst +2
-0The fields are in network (big endian) byte order meaning that the most significant byte (MSB) is stored at the lowest address. +Message Format +============== OP_REQ_DEVLIST: Retrieve the list of exported USB devices.@@ -102,7 +131,7 @@ OP_REQ_DEVLIST: +-----------+--------+------------+---------------------------------------------------+ | Offset | Length | Value | Description |Quoted 8 lines
Documentation/usb/usbip_protocol.rst OP_REQ_DEVLIST: · line 135
Quoted 4 lines
Documentation/usb/usbip_protocol.rst +1
-1+===========+========+============+===================================================+ -| 0 | 2 | 0x0100 | Binary-coded decimal USBIP version number: v1.0.0 | +| 0 | 2 | 0x0111 | Binary-coded decimal USBIP version number: v1.1.1 | +-----------+--------+------------+---------------------------------------------------+Let's make this vx.x.x and specify current version number at the top. Saves us doc updates as we change version number - one location change as opposed to the entire document
Quoted 5 lines
Will be adopted in the next version of the PATCH.
A sidenote though, the version number has not changed since the release (out of staging) of usbip.
Yes. Agreed. It may never change. However, it will be easier to not have to update the document in multiple places. Also reference where the version is - config.h has this defined.
Quoted 331 lines
Quoted 321 lines
Quoted 321 lines
Documentation/usb/usbip_protocol.rst +131
-145| 2 | 2 | 0x8005 | Command code: Retrieve the list of exported USB | | | | | devices. |@@ -116,7 +145,7 @@ OP_REP_DEVLIST: +-----------+--------+------------+---------------------------------------------------+ | Offset | Length | Value | Description | +===========+========+============+===================================================+ -| 0 | 2 | 0x0100 | Binary-coded decimal USBIP version number: v1.0.0.| +| 0 | 2 | 0x0111 | Binary-coded decimal USBIP version number: v1.1.1 | +-----------+--------+------------+---------------------------------------------------+ | 2 | 2 | 0x0005 | Reply code: The list of exported USB devices. | +-----------+--------+------------+---------------------------------------------------+@@ -165,8 +194,8 @@ OP_REP_DEVLIST: | 0x143 | 1 | | bNumInterfaces | +-----------+--------+------------+---------------------------------------------------+ | 0x144 | | m_0 | From now on each interface is described, all | -| | | | together bNumInterfaces times, with the | -| | | | the following 4 fields: | +| | | | together bNumInterfaces times, with the following | +| | | | 4 fields: | +-----------+--------+------------+---------------------------------------------------+ | | 1 | | bInterfaceClass | +-----------+--------+------------+---------------------------------------------------+@@ -177,7 +206,7 @@ OP_REP_DEVLIST: | 0x147 | 1 | | padding byte for alignment, shall be set to zero | +-----------+--------+------------+---------------------------------------------------+ | 0xC + | | | The second exported USB device starts at i=1 | -| i*0x138 + | | | with the busid field. | +| i*0x138 + | | | with the path field. | | m_(i-1)*4 | | | | +-----------+--------+------------+---------------------------------------------------+@@ -187,7 +216,7 @@ OP_REQ_IMPORT: +-----------+--------+------------+---------------------------------------------------+ | Offset | Length | Value | Description | +===========+========+============+===================================================+ -| 0 | 2 | 0x0100 | Binary-coded decimal USBIP version number: v1.0.0 | +| 0 | 2 | 0x0111 | Binary-coded decimal USBIP version number: v1.1.1 | +-----------+--------+------------+---------------------------------------------------+ | 2 | 2 | 0x8003 | Command code: import a remote USB device. | +-----------+--------+------------+---------------------------------------------------+@@ -206,7 +235,7 @@ OP_REP_IMPORT: +-----------+--------+------------+---------------------------------------------------+ | Offset | Length | Value | Description | +===========+========+============+===================================================+ -| 0 | 2 | 0x0100 | Binary-coded decimal USBIP version number: v1.0.0 | +| 0 | 2 | 0x0111 | Binary-coded decimal USBIP version number: v1.1.1 | +-----------+--------+------------+---------------------------------------------------+ | 2 | 2 | 0x0003 | Reply code: Reply to import. | +-----------+--------+------------+---------------------------------------------------+@@ -254,158 +283,151 @@ OP_REP_IMPORT: | 0x13E | 1 | | bNumInterfaces | +-----------+--------+------------+---------------------------------------------------+ -USBIP_CMD_SUBMIT: - Submit an URB +The following four commands have a common basic header called +'usbip_header_basic', and their headers, called 'usbip_header' (before URB +payload), have the same length, therefore paddings are needed. -+-----------+--------+------------+---------------------------------------------------+ -| Offset | Length | Value | Description | -+===========+========+============+===================================================+ -| 0 | 4 | 0x00000001 | command: Submit an URB | -+-----------+--------+------------+---------------------------------------------------+ -| 4 | 4 | | seqnum: the sequence number of the URB to submit | -+-----------+--------+------------+---------------------------------------------------+ -| 8 | 4 | | devid | -+-----------+--------+------------+---------------------------------------------------+ -| 0xC | 4 | | direction: | -| | | | | -| | | | - 0: USBIP_DIR_OUT | -| | | | - 1: USBIP_DIR_IN | -+-----------+--------+------------+---------------------------------------------------+ -| 0x10 | 4 | | ep: endpoint number, possible values are: 0...15 | -+-----------+--------+------------+---------------------------------------------------+ -| 0x14 | 4 | | transfer_flags: possible values depend on the | -| | | | URB transfer type, see below | -+-----------+--------+------------+---------------------------------------------------+ -| 0x18 | 4 | | transfer_buffer_length | -+-----------+--------+------------+---------------------------------------------------+ -| 0x1C | 4 | | start_frame: specify the selected frame to | -| | | | transmit an ISO frame, ignored if URB_ISO_ASAP | -| | | | is specified at transfer_flags | -+-----------+--------+------------+---------------------------------------------------+ -| 0x20 | 4 | | number_of_packets: number of ISO packets | -+-----------+--------+------------+---------------------------------------------------+ -| 0x24 | 4 | | interval: maximum time for the request on the | -| | | | server-side host controller | -+-----------+--------+------------+---------------------------------------------------+ -| 0x28 | 8 | | setup: data bytes for USB setup, filled with | -| | | | zeros if not used | -+-----------+--------+------------+---------------------------------------------------+ -| 0x30 | | | URB data. For ISO transfers the padding between | -| | | | each ISO packets is not transmitted. | -+-----------+--------+------------+---------------------------------------------------+ +usbip_header_basic: ++-----------+--------+---------------------------------------------------+ +| Offset | Length | Description | ++===========+========+===================================================+ +| 0 | 4 | command | ++-----------+--------+---------------------------------------------------+ +| 4 | 4 | seqnum: sequential number that identifies requests| +| | | and corresponding responses; | +| | | incremented per connection | ++-----------+--------+---------------------------------------------------+ +| 8 | 4 | devid: specifies a remote USB device uniquely | +| | | instead of busnum and devnum; | +| | | for client (request), this value is | +| | | ((busnum << 16) | devnum); | +| | | for server (response), this shall be set to 0 | ++-----------+--------+---------------------------------------------------+ +| 0xC | 4 | direction: | +| | | | +| | | - 0: USBIP_DIR_OUT | +| | | - 1: USBIP_DIR_IN | +| | | | +| | | only used by client, for server this shall be 0 | ++-----------+--------+---------------------------------------------------+ +| 0x10 | 4 | ep: endpoint number | +| | | only used by client, for server this shall be 0; | +| | | for UNLINK, this shall be 0 | ++-----------+--------+---------------------------------------------------+ - +-------------------------+------------+---------+-----------+----------+-------------+ - | Allowed transfer_flags | value | control | interrupt | bulk | isochronous | - +=========================+============+=========+===========+==========+=============+ - | URB_SHORT_NOT_OK | 0x00000001 | only in | only in | only in | no | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_ISO_ASAP | 0x00000002 | no | no | no | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_NO_TRANSFER_DMA_MAP | 0x00000004 | yes | yes | yes | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_ZERO_PACKET | 0x00000040 | no | no | only out | no | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_NO_INTERRUPT | 0x00000080 | yes | yes | yes | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_FREE_BUFFER | 0x00000100 | yes | yes | yes | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_DIR_MASK | 0x00000200 | yes | yes | yes | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ +USBIP_CMD_SUBMIT: + Submit an URB ++-----------+--------+---------------------------------------------------+ +| Offset | Length | Description | ++===========+========+===================================================+ +| 0 | 20 | usbip_header_basic, 'command' shall be 0x00000001 | ++-----------+--------+---------------------------------------------------+ +| 0x14 | 4 | transfer_flags: possible values depend on the | +| | | URB transfer_flags, | +| | | but with URB_NO_TRANSFER_DMA_MAP masked | ++-----------+--------+---------------------------------------------------+ +| 0x18 | 4 | transfer_buffer_length: | +| | | use URB transfer_buffer_length | ++-----------+--------+---------------------------------------------------+ +| 0x1C | 4 | start_frame: use URB start_frame; | +| | | initial frame for ISO transfer; | +| | | shall be set to 0 if not ISO transfer | ++-----------+--------+---------------------------------------------------+ +| 0x20 | 4 | number_of_packets: number of ISO packets; | +| | | shall be set to 0xffffffff if not ISO transfer | ++-----------+--------+---------------------------------------------------+ +| 0x24 | 4 | interval: maximum time for the request on the | +| | | server-side host controller | ++-----------+--------+---------------------------------------------------+ +| 0x28 | 8 | setup: data bytes for USB setup, filled with | +| | | zeros if not used. | ++-----------+--------+---------------------------------------------------+ +| 0x30 | n | transfer_buffer. | +| | | If direction is USBIP_DIR_OUT then n equals | +| | | transfer_buffer_length; otherwise n equals 0. | +| | | For ISO transfers the padding between each ISO | +| | | packets is not transmitted. | ++-----------+--------+---------------------------------------------------+ +| 0x30+n | m | iso_packet_descriptor | ++-----------+--------+---------------------------------------------------+ USBIP_RET_SUBMIT: Reply for submitting an URB -+-----------+--------+------------+---------------------------------------------------+ -| Offset | Length | Value | Description | -+===========+========+============+===================================================+ -| 0 | 4 | 0x00000003 | command | -+-----------+--------+------------+---------------------------------------------------+ -| 4 | 4 | | seqnum: URB sequence number | -+-----------+--------+------------+---------------------------------------------------+ -| 8 | 4 | | devid | -+-----------+--------+------------+---------------------------------------------------+ -| 0xC | 4 | | direction: | -| | | | | -| | | | - 0: USBIP_DIR_OUT | -| | | | - 1: USBIP_DIR_IN | -+-----------+--------+------------+---------------------------------------------------+ -| 0x10 | 4 | | ep: endpoint number | -+-----------+--------+------------+---------------------------------------------------+ -| 0x14 | 4 | | status: zero for successful URB transaction, | -| | | | otherwise some kind of error happened. | -+-----------+--------+------------+---------------------------------------------------+ -| 0x18 | 4 | n | actual_length: number of URB data bytes | -+-----------+--------+------------+---------------------------------------------------+ -| 0x1C | 4 | | start_frame: for an ISO frame the actually | -| | | | selected frame for transmit. | -+-----------+--------+------------+---------------------------------------------------+ -| 0x20 | 4 | | number_of_packets | -+-----------+--------+------------+---------------------------------------------------+ -| 0x24 | 4 | | error_count | -+-----------+--------+------------+---------------------------------------------------+ -| 0x28 | 8 | | setup: data bytes for USB setup, filled with | -| | | | zeros if not used | -+-----------+--------+------------+---------------------------------------------------+ -| 0x30 | n | | URB data bytes. For ISO transfers the padding | -| | | | between each ISO packets is not transmitted. | -+-----------+--------+------------+---------------------------------------------------+ ++-----------+--------+---------------------------------------------------+ +| Offset | Length | Description | ++===========+========+===================================================+ +| 0 | 20 | usbip_header_basic, 'command' shall be 0x00000003 | ++-----------+--------+---------------------------------------------------+ +| 0x14 | 4 | status: zero for successful URB transaction, | +| | | otherwise some kind of error happened. | ++-----------+--------+---------------------------------------------------+ +| 0x18 | 4 | actual_length: number of URB data bytes; | +| | | use URB actual_length | ++-----------+--------+---------------------------------------------------+ +| 0x1C | 4 | start_frame: use URB start_frame; | +| | | initial frame for ISO transfer; | +| | | shall be set to 0 if not ISO transfer | ++-----------+--------+---------------------------------------------------+ +| 0x20 | 4 | number_of_packets: number of ISO packets; | +| | | shall be set to 0xffffffff if not ISO transfer | ++-----------+--------+---------------------------------------------------+ +| 0x24 | 4 | error_count | ++-----------+--------+---------------------------------------------------+ +| 0x28 | 8 | padding, shall be set to 0 | ++-----------+--------+---------------------------------------------------+ +| 0x30 | n | transfer_buffer. | +| | | If direction is USBIP_DIR_IN then n equals | +| | | actual_length; otherwise n equals 0. | +| | | For ISO transfers the padding between each ISO | +| | | packets is not transmitted. | ++-----------+--------+---------------------------------------------------+ +| 0x30+n | m | iso_packet_descriptor | ++-----------+--------+---------------------------------------------------+ USBIP_CMD_UNLINK: Unlink an URB -+-----------+--------+------------+---------------------------------------------------+ -| Offset | Length | Value | Description | -+===========+========+============+===================================================+ -| 0 | 4 | 0x00000002 | command: URB unlink command | -+-----------+--------+------------+---------------------------------------------------+ -| 4 | 4 | | seqnum: URB sequence number to unlink: | -| | | | | -| | | | FIXME: | -| | | | is this so? | -+-----------+--------+------------+---------------------------------------------------+ -| 8 | 4 | | devid | -+-----------+--------+------------+---------------------------------------------------+ -| 0xC | 4 | | direction: | -| | | | | -| | | | - 0: USBIP_DIR_OUT | -| | | | - 1: USBIP_DIR_IN | -+-----------+--------+------------+---------------------------------------------------+ -| 0x10 | 4 | | ep: endpoint number: zero | -+-----------+--------+------------+---------------------------------------------------+ -| 0x14 | 4 | | seqnum: the URB sequence number given previously | -| | | | at USBIP_CMD_SUBMIT.seqnum field | -+-----------+--------+------------+---------------------------------------------------+ -| 0x30 | n | | URB data bytes. For ISO transfers the padding | -| | | | between each ISO packets is not transmitted. | -+-----------+--------+------------+---------------------------------------------------+ ++-----------+--------+---------------------------------------------------+ +| Offset | Length | Description | ++===========+========+===================================================+ +| 0 | 20 | usbip_header_basic, 'command' shall be 0x00000002 | ++-----------+--------+---------------------------------------------------+ +| 0x14 | 4 | unlink_seqnum, of the SUBMIT request to unlink | ++-----------+--------+---------------------------------------------------+ +| 0x18 | 24 | padding, shall be set to 0 | ++-----------+--------+---------------------------------------------------+ USBIP_RET_UNLINK: Reply for URB unlink -+-----------+--------+------------+---------------------------------------------------+ -| Offset | Length | Value | Description | -+===========+========+============+===================================================+ -| 0 | 4 | 0x00000004 | command: reply for the URB unlink command | -+-----------+--------+------------+---------------------------------------------------+ -| 4 | 4 | | seqnum: the unlinked URB sequence number | -+-----------+--------+------------+---------------------------------------------------+ -| 8 | 4 | | devid | -+-----------+--------+------------+---------------------------------------------------+ -| 0xC | 4 | | direction: | -| | | | | -| | | | - 0: USBIP_DIR_OUT | -| | | | - 1: USBIP_DIR_IN | -+-----------+--------+------------+---------------------------------------------------+ -| 0x10 | 4 | | ep: endpoint number | -+-----------+--------+------------+---------------------------------------------------+ -| 0x14 | 4 | | status: This is the value contained in the | -| | | | urb->status in the URB completition handler. | -| | | | | -| | | | FIXME: | -| | | | a better explanation needed. | -+-----------+--------+------------+---------------------------------------------------+ -| 0x30 | n | | URB data bytes. For ISO transfers the padding | -| | | | between each ISO packets is not transmitted. | -+-----------+--------+------------+---------------------------------------------------+ ++-----------+--------+---------------------------------------------------+ +| Offset | Length | Description | ++===========+========+===================================================+ +| 0 | 20 | usbip_header_basic, 'command' shall be 0x00000004 | ++-----------+--------+---------------------------------------------------+ +| 0x14 | 4 | status: This is similar to the status of | +| | | USBIP_RET_SUBMIT (share the same memory offset). | +| | | When UNLINK is successful, status is -ECONNRESET; | +| | | when USBIP_CMD_UNLINK is after USBIP_RET_SUBMIT | +| | | status is 0 | ++-----------+--------+---------------------------------------------------+ +| 0x18 | 24 | padding, shall be set to 0 | ++-----------+--------+---------------------------------------------------+ + +EXAMPLE +======= + + The following data is captured from wire with Human Interface Devices (HID) + payload + +::Quoted 9 lines
Documentation/usb/usbip_protocol.rst OP_REP_IMPORT:
Quoted 8 lines
Documentation/usb/usbip_protocol.rst +7
-0+ + CmdIntrIN: 00000001 00000d05 0001000f 00000001 00000001 00000200 00000040 ffffffff 00000000 00000004 00000000 00000000 + CmdIntrOUT: 00000001 00000d06 0001000f 00000000 00000001 00000000 00000040 ffffffff 00000000 00000004 00000000 00000000 + ffffffff860008a784ce5ae212376300000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 + RetIntrOut: 00000003 00000d06 00000000 00000000 00000000 00000000 00000040 ffffffff 00000000 00000000 00000000 00000000 + RetIntrIn: 00000003 00000d05 00000000 00000000 00000000 00000000 00000040 ffffffff 00000000 00000000 00000000 00000000 + ffffffff860011a784ce5ae2123763612891b1020100000400000000000000000000000000000000000000000000000000000000000000000000000000000000
Quoted 3 lines
I will submit the next version of the PATCH after all the conversations above resolved.
Sounds good. Thanks for doing this work.
thanks,
-- Shuah
Hongren Zheng (Zenithal)
reviewerPATCH v6 1/1 docs: usbip: Fix major fields and descriptions in protocol
In reply to Hongren Zheng (Zenithal)The old document for usbip protocol is misleading and hard to read:
* Some fields in header are incorrect
* Explanation of some fields are unclear or even wrong
* Padding of header (namely all headers have the same length) is not explicitly pointed out, which is crucial for stream protocol like TCP
Major changes:
* Document the correct field as described in the codebase.
* Document the padding in usbip headers. This is crucial for TCP stream hence these padding should be explicitly point out. In code these padding are implemented by a union of all headers.
* Fix two FIXME related to usbip unlink and Document the behavior of unlink in different situation.
* Clarify some field with more accurate explanation, like those fields associated with URB. Some constraints are extracted from code.
* Delete specific transfer_flag doc in usbip as it should be documented by the URB doc in Documentation/driver-api/usb/URB.rst
* Add data captured from wire as example
Version change:
From "PRELIMINARY DRAFT, MAY CONTAIN MISTAKES, 28 Jun 2011" To "Version 1, 31 Mar 2021"
--- Documentation/usb/usbip_protocol.rst | 344 +++++++++++++++------------ 1 file changed, 193 insertions(+), 151 deletions(-)
PATCH v2:
Some changes suggested by a previous patch in
https://lore.kernel.org/linux-usb
/[email protected]/
is adopted in this patch.
* Fix Typo: duplicated 'the' in 'the following 4 field'
* Fix incorrect field: in OP_REQ_DEVLIST, the second dev starts with field 'path', not 'busid'
PATCH v3:
Suggested by
https://lore.kernel.org/linux-doc/YE8Oan2BmSuKR4%[email protected]/
* Remove date and changelog in doc as these are tracked in git history
* Remove 'mistake alert' as all data fields are documented properly now. However, docs on possible values for some field shall be added in the future
PATCH v4:
Suggested by https://lore.kernel.org/linux-doc
/[email protected]/
* Add punctuations for readability
* Move patch changelog after the marker line
* Remove nickname in signed-off-by line
PATCH v5:
* Instead of co-developed-by, use reviewed-by
for Randy Dunlap
PATCH v6:
* Add reference to URB doc in changelog
* Add version change in changelog
* Add reference to URB doc for transfer_flag and other fields in USBIP_CMD_SUBMIT
* Add reference to specific functions for UNLINK behavior and transfer_flag
* Fix typo: "clients import", "connection to the server" and "USBIP_RET_UNLINK" to "USBIP_RET_SUBMIT" in UNLINK behavior part
* Separate the flow of UNLINK for clarity
* Extract the version number in message headers to one separate section for ease of maintainence
Documentation/usb/usbip_protocol.rst +193 -151
@@ -2,15 +2,15 @@ USB/IP protocol =============== -PRELIMINARY DRAFT, MAY CONTAIN MISTAKES! -28 Jun 2011 +Architecture +============ The USB/IP protocol follows a server/client architecture. The server exports the -USB devices and the clients imports them. The device driver for the exported +USB devices and the clients import them. The device driver for the exported USB device runs on the client machine. The client may ask for the list of the exported USB devices. To get the list the -client opens a TCP/IP connection towards the server, and sends an OP_REQ_DEVLIST +client opens a TCP/IP connection to the server, and sends an OP_REQ_DEVLIST packet on top of the TCP/IP connection (so the actual OP_REQ_DEVLIST may be sent in one or more pieces at the low level transport layer). The server sends back the OP_REP_DEVLIST packet which lists the exported USB devices. Finally the
@@ -30,7 +30,7 @@ TCP/IP connection is closed. | | Once the client knows the list of exported USB devices it may decide to use one -of them. First the client opens a TCP/IP connection towards the server and +of them. First the client opens a TCP/IP connection to the server and sends an OP_REQ_IMPORT packet. The server replies with OP_REP_IMPORT. If the import was successful the TCP/IP connection remains open and will be used to transfer the URB traffic between the client and the server. The client may
@@ -84,17 +84,61 @@ server may be USBIP_RET_SUBMIT and USBIP_RET_UNLINK respectively. | <---------------------------------------------- | | . | | : | + +For UNLINK, note that after a successful USBIP_RET_UNLINK, the unlinked URB +submission would not have a corresponding USBIP_RET_SUBMIT (this is explained in +function stub_recv_cmd_unlink of drivers/usb/usbip/stub_rx.c). + +:: + + virtual host controller usb host + "client" "server" + (imports USB devices) (exports USB devices) + | | + | USBIP_CMD_SUBMIT(seqnum = p) | + | ----------------------------------------------> | | | | USBIP_CMD_UNLINK | + | (seqnum = p+1, unlink_seqnum = p) | | ----------------------------------------------> | | | | USBIP_RET_UNLINK | + | (seqnum = p+1, status = -ECONNRESET) | + | <---------------------------------------------- | + | | + | Note: No USBIP_RET_SUBMIT(seqnum = p) | + | <--X---X---X---X---X---X---X---X---X---X---X--- | + | . | + | : | + | | + | USBIP_CMD_SUBMIT(seqnum = q) | + | ----------------------------------------------> | + | | + | USBIP_RET_SUBMIT(seqnum = q) | + | <---------------------------------------------- | + | | + | USBIP_CMD_UNLINK | + | (seqnum = q+1, unlink_seqnum = q) | + | ----------------------------------------------> | + | | + | USBIP_RET_UNLINK | + | (seqnum = q+1, status = 0) | | <---------------------------------------------- | | | The fields are in network (big endian) byte order meaning that the most significant byte (MSB) is stored at the lowest address. +Protocol Version +================ + +The documented USBIP version is v1.1.1. The binary representation of this +version in message headers is 0x0111. + +This is defined in tools/usb/usbip/configure.ac + +Message Format +============== OP_REQ_DEVLIST: Retrieve the list of exported USB devices.
@@ -102,7 +146,7 @@ OP_REQ_DEVLIST: +-----------+--------+------------+---------------------------------------------------+ | Offset | Length | Value | Description | +===========+========+============+===================================================+ -| 0 | 2 | 0x0100 | Binary-coded decimal USBIP version number: v1.0.0 | +| 0 | 2 | | USBIP version | +-----------+--------+------------+---------------------------------------------------+ | 2 | 2 | 0x8005 | Command code: Retrieve the list of exported USB | | | | | devices. |
@@ -116,7 +160,7 @@ OP_REP_DEVLIST: +-----------+--------+------------+---------------------------------------------------+ | Offset | Length | Value | Description | +===========+========+============+===================================================+ -| 0 | 2 | 0x0100 | Binary-coded decimal USBIP version number: v1.0.0.| +| 0 | 2 | | USBIP version | +-----------+--------+------------+---------------------------------------------------+ | 2 | 2 | 0x0005 | Reply code: The list of exported USB devices. | +-----------+--------+------------+---------------------------------------------------+
@@ -165,8 +209,8 @@ OP_REP_DEVLIST: | 0x143 | 1 | | bNumInterfaces | +-----------+--------+------------+---------------------------------------------------+ | 0x144 | | m_0 | From now on each interface is described, all | -| | | | together bNumInterfaces times, with the | -| | | | the following 4 fields: | +| | | | together bNumInterfaces times, with the following | +| | | | 4 fields: | +-----------+--------+------------+---------------------------------------------------+ | | 1 | | bInterfaceClass | +-----------+--------+------------+---------------------------------------------------+
@@ -177,7 +221,7 @@ OP_REP_DEVLIST: | 0x147 | 1 | | padding byte for alignment, shall be set to zero | +-----------+--------+------------+---------------------------------------------------+ | 0xC + | | | The second exported USB device starts at i=1 | -| i*0x138 + | | | with the busid field. | +| i*0x138 + | | | with the path field. | | m_(i-1)*4 | | | | +-----------+--------+------------+---------------------------------------------------+
@@ -187,7 +231,7 @@ OP_REQ_IMPORT: +-----------+--------+------------+---------------------------------------------------+ | Offset | Length | Value | Description | +===========+========+============+===================================================+ -| 0 | 2 | 0x0100 | Binary-coded decimal USBIP version number: v1.0.0 | +| 0 | 2 | | USBIP version | +-----------+--------+------------+---------------------------------------------------+ | 2 | 2 | 0x8003 | Command code: import a remote USB device. | +-----------+--------+------------+---------------------------------------------------+
@@ -206,7 +250,7 @@ OP_REP_IMPORT: +-----------+--------+------------+---------------------------------------------------+ | Offset | Length | Value | Description | +===========+========+============+===================================================+ -| 0 | 2 | 0x0100 | Binary-coded decimal USBIP version number: v1.0.0 | +| 0 | 2 | | USBIP version | +-----------+--------+------------+---------------------------------------------------+ | 2 | 2 | 0x0003 | Reply code: Reply to import. | +-----------+--------+------------+---------------------------------------------------+
@@ -254,158 +298,156 @@ OP_REP_IMPORT: | 0x13E | 1 | | bNumInterfaces | +-----------+--------+------------+---------------------------------------------------+ -USBIP_CMD_SUBMIT: - Submit an URB +The following four commands have a common basic header called +'usbip_header_basic', and their headers, called 'usbip_header' (before +transfer_buffer payload), have the same length, therefore paddings are needed. -+-----------+--------+------------+---------------------------------------------------+ -| Offset | Length | Value | Description | -+===========+========+============+===================================================+ -| 0 | 4 | 0x00000001 | command: Submit an URB | -+-----------+--------+------------+---------------------------------------------------+ -| 4 | 4 | | seqnum: the sequence number of the URB to submit | -+-----------+--------+------------+---------------------------------------------------+ -| 8 | 4 | | devid | -+-----------+--------+------------+---------------------------------------------------+ -| 0xC | 4 | | direction: | -| | | | | -| | | | - 0: USBIP_DIR_OUT | -| | | | - 1: USBIP_DIR_IN | -+-----------+--------+------------+---------------------------------------------------+ -| 0x10 | 4 | | ep: endpoint number, possible values are: 0...15 | -+-----------+--------+------------+---------------------------------------------------+ -| 0x14 | 4 | | transfer_flags: possible values depend on the | -| | | | URB transfer type, see below | -+-----------+--------+------------+---------------------------------------------------+ -| 0x18 | 4 | | transfer_buffer_length | -+-----------+--------+------------+---------------------------------------------------+ -| 0x1C | 4 | | start_frame: specify the selected frame to | -| | | | transmit an ISO frame, ignored if URB_ISO_ASAP | -| | | | is specified at transfer_flags | -+-----------+--------+------------+---------------------------------------------------+ -| 0x20 | 4 | | number_of_packets: number of ISO packets | -+-----------+--------+------------+---------------------------------------------------+ -| 0x24 | 4 | | interval: maximum time for the request on the | -| | | | server-side host controller | -+-----------+--------+------------+---------------------------------------------------+ -| 0x28 | 8 | | setup: data bytes for USB setup, filled with | -| | | | zeros if not used | -+-----------+--------+------------+---------------------------------------------------+ -| 0x30 | | | URB data. For ISO transfers the padding between | -| | | | each ISO packets is not transmitted. | -+-----------+--------+------------+---------------------------------------------------+ +usbip_header_basic: ++-----------+--------+---------------------------------------------------+ +| Offset | Length | Description | ++===========+========+===================================================+ +| 0 | 4 | command | ++-----------+--------+---------------------------------------------------+ +| 4 | 4 | seqnum: sequential number that identifies requests| +| | | and corresponding responses; | +| | | incremented per connection | ++-----------+--------+---------------------------------------------------+ +| 8 | 4 | devid: specifies a remote USB device uniquely | +| | | instead of busnum and devnum; | +| | | for client (request), this value is | +| | | ((busnum << 16) | devnum); | +| | | for server (response), this shall be set to 0 | ++-----------+--------+---------------------------------------------------+ +| 0xC | 4 | direction: | +| | | | +| | | - 0: USBIP_DIR_OUT | +| | | - 1: USBIP_DIR_IN | +| | | | +| | | only used by client, for server this shall be 0 | ++-----------+--------+---------------------------------------------------+ +| 0x10 | 4 | ep: endpoint number | +| | | only used by client, for server this shall be 0; | +| | | for UNLINK, this shall be 0 | ++-----------+--------+---------------------------------------------------+ - +-------------------------+------------+---------+-----------+----------+-------------+ - | Allowed transfer_flags | value | control | interrupt | bulk | isochronous | - +=========================+============+=========+===========+==========+=============+ - | URB_SHORT_NOT_OK | 0x00000001 | only in | only in | only in | no | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_ISO_ASAP | 0x00000002 | no | no | no | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_NO_TRANSFER_DMA_MAP | 0x00000004 | yes | yes | yes | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_ZERO_PACKET | 0x00000040 | no | no | only out | no | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_NO_INTERRUPT | 0x00000080 | yes | yes | yes | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_FREE_BUFFER | 0x00000100 | yes | yes | yes | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ - | URB_DIR_MASK | 0x00000200 | yes | yes | yes | yes | - +-------------------------+------------+---------+-----------+----------+-------------+ +USBIP_CMD_SUBMIT: + Submit an URB ++-----------+--------+---------------------------------------------------+ +| Offset | Length | Description | ++===========+========+===================================================+ +| 0 | 20 | usbip_header_basic, 'command' shall be 0x00000001 | ++-----------+--------+---------------------------------------------------+ +| 0x14 | 4 | transfer_flags: possible values depend on the | +| | | URB transfer_flags (refer to URB doc in | +| | | Documentation/driver-api/usb/URB.rst) | +| | | but with URB_NO_TRANSFER_DMA_MAP masked. Refer to | +| | | function usbip_pack_cmd_submit and function | +| | | tweak_transfer_flags in drivers/usb/usbip/ | +| | | usbip_common.c. The following fields may also ref | +| | | to function usbip_pack_cmd_submit and URB doc | ++-----------+--------+---------------------------------------------------+ +| 0x18 | 4 | transfer_buffer_length: | +| | | use URB transfer_buffer_length | ++-----------+--------+---------------------------------------------------+ +| 0x1C | 4 | start_frame: use URB start_frame; | +| | | initial frame for ISO transfer; | +| | | shall be set to 0 if not ISO transfer | ++-----------+--------+---------------------------------------------------+ +| 0x20 | 4 | number_of_packets: number of ISO packets; | +| | | shall be set to 0xffffffff if not ISO transfer | ++-----------+--------+---------------------------------------------------+ +| 0x24 | 4 | interval: maximum time for the request on the | +| | | server-side host controller | ++-----------+--------+---------------------------------------------------+ +| 0x28 | 8 | setup: data bytes for USB setup, filled with | +| | | zeros if not used. | ++-----------+--------+---------------------------------------------------+ +| 0x30 | n | transfer_buffer. | +| | | If direction is USBIP_DIR_OUT then n equals | +| | | transfer_buffer_length; otherwise n equals 0. | +| | | For ISO transfers the padding between each ISO | +| | | packets is not transmitted. | ++-----------+--------+---------------------------------------------------+ +| 0x30+n | m | iso_packet_descriptor | ++-----------+--------+---------------------------------------------------+ USBIP_RET_SUBMIT: Reply for submitting an URB -+-----------+--------+------------+---------------------------------------------------+ -| Offset | Length | Value | Description | -+===========+========+============+===================================================+ -| 0 | 4 | 0x00000003 | command | -+-----------+--------+------------+---------------------------------------------------+ -| 4 | 4 | | seqnum: URB sequence number | -+-----------+--------+------------+---------------------------------------------------+ -| 8 | 4 | | devid | -+-----------+--------+------------+---------------------------------------------------+ -| 0xC | 4 | | direction: | -| | | | | -| | | | - 0: USBIP_DIR_OUT | -| | | | - 1: USBIP_DIR_IN | -+-----------+--------+------------+---------------------------------------------------+ -| 0x10 | 4 | | ep: endpoint number | -+-----------+--------+------------+---------------------------------------------------+ -| 0x14 | 4 | | status: zero for successful URB transaction, | -| | | | otherwise some kind of error happened. | -+-----------+--------+------------+---------------------------------------------------+ -| 0x18 | 4 | n | actual_length: number of URB data bytes | -+-----------+--------+------------+---------------------------------------------------+ -| 0x1C | 4 | | start_frame: for an ISO frame the actually | -| | | | selected frame for transmit. | -+-----------+--------+------------+---------------------------------------------------+ -| 0x20 | 4 | | number_of_packets | -+-----------+--------+------------+---------------------------------------------------+ -| 0x24 | 4 | | error_count | -+-----------+--------+------------+---------------------------------------------------+ -| 0x28 | 8 | | setup: data bytes for USB setup, filled with | -| | | | zeros if not used | -+-----------+--------+------------+---------------------------------------------------+ -| 0x30 | n | | URB data bytes. For ISO transfers the padding | -| | | | between each ISO packets is not transmitted. | -+-----------+--------+------------+---------------------------------------------------+ ++-----------+--------+---------------------------------------------------+ +| Offset | Length | Description | ++===========+========+===================================================+ +| 0 | 20 | usbip_header_basic, 'command' shall be 0x00000003 | ++-----------+--------+---------------------------------------------------+ +| 0x14 | 4 | status: zero for successful URB transaction, | +| | | otherwise some kind of error happened. | ++-----------+--------+---------------------------------------------------+ +| 0x18 | 4 | actual_length: number of URB data bytes; | +| | | use URB actual_length | ++-----------+--------+---------------------------------------------------+ +| 0x1C | 4 | start_frame: use URB start_frame; | +| | | initial frame for ISO transfer; | +| | | shall be set to 0 if not ISO transfer | ++-----------+--------+---------------------------------------------------+ +| 0x20 | 4 | number_of_packets: number of ISO packets; | +| | | shall be set to 0xffffffff if not ISO transfer | ++-----------+--------+---------------------------------------------------+ +| 0x24 | 4 | error_count | ++-----------+--------+---------------------------------------------------+ +| 0x28 | 8 | padding, shall be set to 0 | ++-----------+--------+---------------------------------------------------+ +| 0x30 | n | transfer_buffer. | +| | | If direction is USBIP_DIR_IN then n equals | +| | | actual_length; otherwise n equals 0. | +| | | For ISO transfers the padding between each ISO | +| | | packets is not transmitted. | ++-----------+--------+---------------------------------------------------+ +| 0x30+n | m | iso_packet_descriptor | ++-----------+--------+---------------------------------------------------+ USBIP_CMD_UNLINK: Unlink an URB -+-----------+--------+------------+---------------------------------------------------+ -| Offset | Length | Value | Description | -+===========+========+============+===================================================+ -| 0 | 4 | 0x00000002 | command: URB unlink command | -+-----------+--------+------------+---------------------------------------------------+ -| 4 | 4 | | seqnum: URB sequence number to unlink: | -| | | | | -| | | | FIXME: | -| | | | is this so? | -+-----------+--------+------------+---------------------------------------------------+ -| 8 | 4 | | devid | -+-----------+--------+------------+---------------------------------------------------+ -| 0xC | 4 | | direction: | -| | | | | -| | | | - 0: USBIP_DIR_OUT | -| | | | - 1: USBIP_DIR_IN | -+-----------+--------+------------+---------------------------------------------------+ -| 0x10 | 4 | | ep: endpoint number: zero | -+-----------+--------+------------+---------------------------------------------------+ -| 0x14 | 4 | | seqnum: the URB sequence number given previously | -| | | | at USBIP_CMD_SUBMIT.seqnum field | -+-----------+--------+------------+---------------------------------------------------+ -| 0x30 | n | | URB data bytes. For ISO transfers the padding | -| | | | between each ISO packets is not transmitted. | -+-----------+--------+------------+---------------------------------------------------+ ++-----------+--------+---------------------------------------------------+ +| Offset | Length | Description | ++===========+========+===================================================+ +| 0 | 20 | usbip_header_basic, 'command' shall be 0x00000002 | ++-----------+--------+---------------------------------------------------+ +| 0x14 | 4 | unlink_seqnum, of the SUBMIT request to unlink | ++-----------+--------+---------------------------------------------------+ +| 0x18 | 24 | padding, shall be set to 0 | ++-----------+--------+---------------------------------------------------+ USBIP_RET_UNLINK: Reply for URB unlink -+-----------+--------+------------+---------------------------------------------------+ -| Offset | Length | Value | Description | -+===========+========+============+===================================================+ -| 0 | 4 | 0x00000004 | command: reply for the URB unlink command | -+-----------+--------+------------+---------------------------------------------------+ -| 4 | 4 | | seqnum: the unlinked URB sequence number | -+-----------+--------+------------+---------------------------------------------------+ -| 8 | 4 | | devid | -+-----------+--------+------------+---------------------------------------------------+ -| 0xC | 4 | | direction: | -| | | | | -| | | | - 0: USBIP_DIR_OUT | -| | | | - 1: USBIP_DIR_IN | -+-----------+--------+------------+---------------------------------------------------+ -| 0x10 | 4 | | ep: endpoint number | -+-----------+--------+------------+---------------------------------------------------+ -| 0x14 | 4 | | status: This is the value contained in the | -| | | | urb->status in the URB completition handler. | -| | | | | -| | | | FIXME: | -| | | | a better explanation needed. | -+-----------+--------+------------+---------------------------------------------------+ -| 0x30 | n | | URB data bytes. For ISO transfers the padding | -| | | | between each ISO packets is not transmitted. | -+-----------+--------+------------+---------------------------------------------------+ ++-----------+--------+---------------------------------------------------+ +| Offset | Length | Description | ++===========+========+===================================================+ +| 0 | 20 | usbip_header_basic, 'command' shall be 0x00000004 | ++-----------+--------+---------------------------------------------------+ +| 0x14 | 4 | status: This is similar to the status of | +| | | USBIP_RET_SUBMIT (share the same memory offset). | +| | | When UNLINK is successful, status is -ECONNRESET; | +| | | when USBIP_CMD_UNLINK is after USBIP_RET_SUBMIT | +| | | status is 0 | ++-----------+--------+---------------------------------------------------+ +| 0x18 | 24 | padding, shall be set to 0 | ++-----------+--------+---------------------------------------------------+ + +EXAMPLE +======= + + The following data is captured from wire with Human Interface Devices (HID) + payload + +:: + + CmdIntrIN: 00000001 00000d05 0001000f 00000001 00000001 00000200 00000040 ffffffff 00000000 00000004 00000000 00000000 + CmdIntrOUT: 00000001 00000d06 0001000f 00000000 00000001 00000000 00000040 ffffffff 00000000 00000004 00000000 00000000 + ffffffff860008a784ce5ae212376300000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 + RetIntrOut: 00000003 00000d06 00000000 00000000 00000000 00000000 00000040 ffffffff 00000000 00000000 00000000 00000000 + RetIntrIn: 00000003 00000d05 00000000 00000000 00000000 00000000 00000040 ffffffff 00000000 00000000 00000000 00000000 + ffffffff860011a784ce5ae2123763612891b1020100000400000000000000000000000000000000000000000000000000000000000000000000000000000000
Signature · 1 line
2.31.0
Quoted 60 lines · Hongren Zheng (Zenithal)
The old document for usbip protocol is misleading and hard to read:
* Some fields in header are incorrect
* Explanation of some fields are unclear or even wrong
* Padding of header (namely all headers have the same length) is not explicitly pointed out, which is crucial for stream protocol like TCPMajor changes:
* Document the correct field as described in the codebase.
* Document the padding in usbip headers. This is crucial for TCP stream hence these padding should be explicitly point out. In code these padding are implemented by a union of all headers.
* Fix two FIXME related to usbip unlink and Document the behavior of unlink in different situation.
* Clarify some field with more accurate explanation, like those fields associated with URB. Some constraints are extracted from code.
* Delete specifictransfer_flagdoc in usbip as it should be documented by the URB doc inDocumentation/driver-api/usb/URB.rst
* Add data captured from wire as exampleVersion change:
From "PRELIMINARY DRAFT, MAY CONTAIN MISTAKES, 28 Jun 2011" To "Version 1, 31 Mar 2021"Co-developed-by Alexandre Demers <[email protected]>Reviewed-by Randy Dunlap <[email protected]>Signed-off-by Hongren Zheng <[email protected]>--- Documentation/usb/usbip_protocol.rst | 344 +++++++++++++++------------ 1 file changed, 193 insertions(+), 151 deletions(-)PATCH v2:
Some changes suggested by a previous patch in
https://lore.kernel.org/linux-usb
/[email protected]/
is adopted in this patch.
* Fix Typo: duplicated 'the' in 'the following 4 field'
* Fix incorrect field: inOP_REQ_DEVLIST, the second dev starts with field 'path', not 'busid'PATCH v3:
Suggested by
https://lore.kernel.org/linux-doc/YE8Oan2BmSuKR4%[email protected]/
* Remove date and changelog in doc as these are tracked in git history
* Remove 'mistake alert' as all data fields are documented properly now. However, docs on possible values for some field shall be added in the futurePATCH v4:
Suggested by https://lore.kernel.org/linux-doc
/[email protected]/
* Add punctuations for readability
* Move patch changelog after the marker line
* Remove nickname in signed-off-by linePATCH v5:
* Instead of co-developed-by, use reviewed-by
for Randy Dunlap
Quoted 13 lines
PATCH v6:
* Add reference to URB doc in changelog
* Add version change in changelog
* Add reference to URB doc fortransfer_flagand other fields inUSBIP_CMD_SUBMIT
* Add reference to specific functions for UNLINK behavior andtransfer_flag
* Fix typo: "clients import", "connection to the server" and "USBIP_RET_UNLINK" to "USBIP_RET_SUBMIT" in UNLINK behavior part
* Separate the flow of UNLINK for clarity
* Extract the version number in message headers to one separate section for ease of maintainence
Thank you for updating the document.
Greg, please pick this up.
thanks,
-- Shuah