Skip to contentSkip to conversation

usb: typec: tcpm: Relax disconnect threshold during power negotiation

PATCH In review Kyle Tso 3 participants 3 messages Jun 16, 2021 – Jun 17, 2021

Subsystems (3)
lore
Share & tools
lore

Kyle Tso

author
#0 lore raw

PATCH v3 1/1 usb: typec: tcpm: Relax disconnect threshold during power negotiation

If the voltage is being decreased in power negotiation, the Source will set the power supply to operate at the new voltage level before sending PS_RDY. Relax the threshold before sending Request Message so that it will not race with Source which begins to adjust the voltage right after it sends Accept Message (PPS) or tSrcTransition (25~35ms) after it sends Accept Message (non-PPS).

The real threshold will be set after Sink receives PS_RDY Message.

Fixes f321a02caebd ("usb: typec: tcpm: Implement enabling Auto Discharge disconnect support")
Cc Badhri Jagan Sridharan <[email protected]>

---
Changes in v3:
- move the timing of setting threshold for Fixed RDO as I did for PPS in v2, i.e. move it to tcpm_pd_send_request.
- add Cc: tag for Badhri
- update the commit message for the above changes

Changes in v2:
- move the timing of setting threshold up to "before sending Request" for PPS power negotiation so that it won't race with the Source.
- PPS: if it fails to send the Request, fallback to previous threshold
- PPS: if the Source doesn't respond Accept, fallback to previous threshold
- update the commit message for above changes

 drivers/usb/typec/tcpm/tcpm.c | 27 +++++++++++++++++++++++++++
 1 file changed, 27 insertions(+)
drivers/usb/typec/tcpm/tcpm.c +27 -0
index 197556038ba4..b1d310ab84c4 100644
@@ -2604,6 +2604,11 @@ static void tcpm_pd_ctrl_request(struct tcpm_port *port,
 			} else {
 				next_state = SNK_WAIT_CAPABILITIES;
 			}
+
+			/* Threshold was relaxed before sending Request. Restore it back. */
+			tcpm_set_auto_vbus_discharge_threshold(port, TYPEC_PWR_MODE_PD,
+							       port->pps_data.active,
+							       port->supply_voltage);
 			tcpm_set_state(port, next_state, 0);
 			break;
 		case SNK_NEGOTIATE_PPS_CAPABILITIES:
@@ -2617,6 +2622,11 @@ static void tcpm_pd_ctrl_request(struct tcpm_port *port,
 			    port->send_discover)
 				port->vdm_sm_running = true;
 
+			/* Threshold was relaxed before sending Request. Restore it back. */
+			tcpm_set_auto_vbus_discharge_threshold(port, TYPEC_PWR_MODE_PD,
+							       port->pps_data.active,
+							       port->supply_voltage);
+
 			tcpm_set_state(port, SNK_READY, 0);
 			break;
 		case DR_SWAP_SEND:
@@ -3336,6 +3346,12 @@ static int tcpm_pd_send_request(struct tcpm_port *port)
 	if (ret < 0)
 		return ret;
 
+	/*
+	 * Relax the threshold as voltage will be adjusted after Accept Message plus tSrcTransition.
+	 * It is safer to modify the threshold here.
+	 */
+	tcpm_set_auto_vbus_discharge_threshold(port, TYPEC_PWR_MODE_USB, false, 0);
+
 	memset(&msg, 0, sizeof(msg));
 	msg.header = PD_HEADER_LE(PD_DATA_REQUEST,
 				  port->pwr_role,
@@ -3433,6 +3449,9 @@ static int tcpm_pd_send_pps_request(struct tcpm_port *port)
 	if (ret < 0)
 		return ret;
 
+	/* Relax the threshold as voltage will be adjusted right after Accept Message. */
+	tcpm_set_auto_vbus_discharge_threshold(port, TYPEC_PWR_MODE_USB, false, 0);
+
 	memset(&msg, 0, sizeof(msg));
 	msg.header = PD_HEADER_LE(PD_DATA_REQUEST,
 				  port->pwr_role,
@@ -4196,6 +4215,10 @@ static void run_state_machine(struct tcpm_port *port)
 		port->hard_reset_count = 0;
 		ret = tcpm_pd_send_request(port);
 		if (ret < 0) {
+			/* Restore back to the original state */
+			tcpm_set_auto_vbus_discharge_threshold(port, TYPEC_PWR_MODE_PD,
+							       port->pps_data.active,
+							       port->supply_voltage);
 			/* Let the Source send capabilities again. */
 			tcpm_set_state(port, SNK_WAIT_CAPABILITIES, 0);
 		} else {
@@ -4206,6 +4229,10 @@ static void run_state_machine(struct tcpm_port *port)
 	case SNK_NEGOTIATE_PPS_CAPABILITIES:
 		ret = tcpm_pd_send_pps_request(port);
 		if (ret < 0) {
+			/* Restore back to the original state */
+			tcpm_set_auto_vbus_discharge_threshold(port, TYPEC_PWR_MODE_PD,
+							       port->pps_data.active,
+							       port->supply_voltage);
 			port->pps_status = ret;
 			/*
 			 * If this was called due to updates to sink
Signature · 1 line
2.32.0.272.g935e593368-goog
maintainer Acked-by on v3 1/1
#1 lore raw
Quoted 7 lines · Kyle Tso

If the voltage is being decreased in power negotiation, the Source will set the power supply to operate at the new voltage level before sending PS_RDY. Relax the threshold before sending Request Message so that it will not race with Source which begins to adjust the voltage right after it sends Accept Message (PPS) or tSrcTransition (25~35ms) after it sends Accept Message (non-PPS).

Quoted 5 lines

The real threshold will be set after Sink receives PS_RDY Message.

Fixes f321a02caebd ("usb: typec: tcpm: Implement enabling Auto Discharge disconnect support")
Cc Badhri Jagan Sridharan <[email protected]>
Quoted 93 lines

---
Changes in v3:
- move the timing of setting threshold for Fixed RDO as I did for PPS in v2, i.e. move it to tcpm_pd_send_request.
- add Cc: tag for Badhri
- update the commit message for the above changes

Changes in v2:
- move the timing of setting threshold up to "before sending Request" for PPS power negotiation so that it won't race with the Source.
- PPS: if it fails to send the Request, fallback to previous threshold
- PPS: if the Source doesn't respond Accept, fallback to previous threshold
- update the commit message for above changes

 drivers/usb/typec/tcpm/tcpm.c | 27 +++++++++++++++++++++++++++
 1 file changed, 27 insertions(+)
drivers/usb/typec/tcpm/tcpm.c +27 -0
index 197556038ba4..b1d310ab84c4 100644
@@ -2604,6 +2604,11 @@ static void tcpm_pd_ctrl_request(struct tcpm_port *port,
 			} else {
 				next_state = SNK_WAIT_CAPABILITIES;
 			}
+
+			/* Threshold was relaxed before sending Request. Restore it back. */
+			tcpm_set_auto_vbus_discharge_threshold(port, TYPEC_PWR_MODE_PD,
+							       port->pps_data.active,
+							       port->supply_voltage);
 			tcpm_set_state(port, next_state, 0);
 			break;
 		case SNK_NEGOTIATE_PPS_CAPABILITIES:
@@ -2617,6 +2622,11 @@ static void tcpm_pd_ctrl_request(struct tcpm_port *port,
 			    port->send_discover)
 				port->vdm_sm_running = true;
 
+			/* Threshold was relaxed before sending Request. Restore it back. */
+			tcpm_set_auto_vbus_discharge_threshold(port, TYPEC_PWR_MODE_PD,
+							       port->pps_data.active,
+							       port->supply_voltage);
+
 			tcpm_set_state(port, SNK_READY, 0);
 			break;
 		case DR_SWAP_SEND:
@@ -3336,6 +3346,12 @@ static int tcpm_pd_send_request(struct tcpm_port *port)
 	if (ret < 0)
 		return ret;
 
+	/*
+	 * Relax the threshold as voltage will be adjusted after Accept Message plus tSrcTransition.
+	 * It is safer to modify the threshold here.
+	 */
+	tcpm_set_auto_vbus_discharge_threshold(port, TYPEC_PWR_MODE_USB, false, 0);
+
 	memset(&msg, 0, sizeof(msg));
 	msg.header = PD_HEADER_LE(PD_DATA_REQUEST,
 				  port->pwr_role,
@@ -3433,6 +3449,9 @@ static int tcpm_pd_send_pps_request(struct tcpm_port *port)
 	if (ret < 0)
 		return ret;
 
+	/* Relax the threshold as voltage will be adjusted right after Accept Message. */
+	tcpm_set_auto_vbus_discharge_threshold(port, TYPEC_PWR_MODE_USB, false, 0);
+
 	memset(&msg, 0, sizeof(msg));
 	msg.header = PD_HEADER_LE(PD_DATA_REQUEST,
 				  port->pwr_role,
@@ -4196,6 +4215,10 @@ static void run_state_machine(struct tcpm_port *port)
 		port->hard_reset_count = 0;
 		ret = tcpm_pd_send_request(port);
 		if (ret < 0) {
+			/* Restore back to the original state */
+			tcpm_set_auto_vbus_discharge_threshold(port, TYPEC_PWR_MODE_PD,
+							       port->pps_data.active,
+							       port->supply_voltage);
 			/* Let the Source send capabilities again. */
 			tcpm_set_state(port, SNK_WAIT_CAPABILITIES, 0);
 		} else {
@@ -4206,6 +4229,10 @@ static void run_state_machine(struct tcpm_port *port)
 	case SNK_NEGOTIATE_PPS_CAPABILITIES:
 		ret = tcpm_pd_send_pps_request(port);
 		if (ret < 0) {
+			/* Restore back to the original state */
+			tcpm_set_auto_vbus_discharge_threshold(port, TYPEC_PWR_MODE_PD,
+							       port->pps_data.active,
+							       port->supply_voltage);
 			port->pps_status = ret;
 			/*
 			 * If this was called due to updates to sink
Signature · 1 line
2.32.0.272.g935e593368-goog
Signature · 1 line
heikki
maintainer Reviewed-by
#2 lore raw
Quoted 9 lines · Heikki Krogerus
Quoted 7 lines · Kyle Tso

If the voltage is being decreased in power negotiation, the Source will set the power supply to operate at the new voltage level before sending PS_RDY. Relax the threshold before sending Request Message so that it will not race with Source which begins to adjust the voltage right after it sends Accept Message (PPS) or tSrcTransition (25~35ms) after it sends Accept Message (non-PPS).

Quoted 7 lines
Quoted 5 lines

The real threshold will be set after Sink receives PS_RDY Message.

Fixes f321a02caebd ("usb: typec: tcpm: Implement enabling Auto Discharge disconnect support")
Cc Badhri Jagan Sridharan <[email protected]>
Quoted 97 lines
Quoted 93 lines

---
Changes in v3:
- move the timing of setting threshold for Fixed RDO as I did for PPS in v2, i.e. move it to tcpm_pd_send_request.
- add Cc: tag for Badhri
- update the commit message for the above changes

Changes in v2:
- move the timing of setting threshold up to "before sending Request" for PPS power negotiation so that it won't race with the Source.
- PPS: if it fails to send the Request, fallback to previous threshold
- PPS: if the Source doesn't respond Accept, fallback to previous threshold
- update the commit message for above changes

 drivers/usb/typec/tcpm/tcpm.c | 27 +++++++++++++++++++++++++++
 1 file changed, 27 insertions(+)
drivers/usb/typec/tcpm/tcpm.c +27 -1
index 197556038ba4..b1d310ab84c4 100644
@@ -2604,6 +2604,11 @@ static void tcpm_pd_ctrl_request(struct tcpm_port *port,
                      } else {
                              next_state = SNK_WAIT_CAPABILITIES;
                      }
+
+                     /* Threshold was relaxed before sending Request. Restore it back. */
+                     tcpm_set_auto_vbus_discharge_threshold(port, TYPEC_PWR_MODE_PD,
+                                                            port->pps_data.active,
+                                                            port->supply_voltage);
                      tcpm_set_state(port, next_state, 0);
                      break;
              case SNK_NEGOTIATE_PPS_CAPABILITIES:
@@ -2617,6 +2622,11 @@ static void tcpm_pd_ctrl_request(struct tcpm_port *port,
                          port->send_discover)
                              port->vdm_sm_running = true;
 
+                     /* Threshold was relaxed before sending Request. Restore it back. */
+                     tcpm_set_auto_vbus_discharge_threshold(port, TYPEC_PWR_MODE_PD,
+                                                            port->pps_data.active,
+                                                            port->supply_voltage);
+
                      tcpm_set_state(port, SNK_READY, 0);
                      break;
              case DR_SWAP_SEND:
@@ -3336,6 +3346,12 @@ static int tcpm_pd_send_request(struct tcpm_port *port)
      if (ret < 0)
              return ret;
 
+     /*
+      * Relax the threshold as voltage will be adjusted after Accept Message plus tSrcTransition.
+      * It is safer to modify the threshold here.
+      */
+     tcpm_set_auto_vbus_discharge_threshold(port, TYPEC_PWR_MODE_USB, false, 0);
+
      memset(&msg, 0, sizeof(msg));
      msg.header = PD_HEADER_LE(PD_DATA_REQUEST,
                                port->pwr_role,
@@ -3433,6 +3449,9 @@ static int tcpm_pd_send_pps_request(struct tcpm_port *port)
      if (ret < 0)
              return ret;
 
+     /* Relax the threshold as voltage will be adjusted right after Accept Message. */
+     tcpm_set_auto_vbus_discharge_threshold(port, TYPEC_PWR_MODE_USB, false, 0);
+
      memset(&msg, 0, sizeof(msg));
      msg.header = PD_HEADER_LE(PD_DATA_REQUEST,
                                port->pwr_role,
@@ -4196,6 +4215,10 @@ static void run_state_machine(struct tcpm_port *port)
              port->hard_reset_count = 0;
              ret = tcpm_pd_send_request(port);
              if (ret < 0) {
+                     /* Restore back to the original state */
+                     tcpm_set_auto_vbus_discharge_threshold(port, TYPEC_PWR_MODE_PD,
+                                                            port->pps_data.active,
+                                                            port->supply_voltage);
                      /* Let the Source send capabilities again. */
                      tcpm_set_state(port, SNK_WAIT_CAPABILITIES, 0);
              } else {
@@ -4206,6 +4229,10 @@ static void run_state_machine(struct tcpm_port *port)
      case SNK_NEGOTIATE_PPS_CAPABILITIES:
              ret = tcpm_pd_send_pps_request(port);
              if (ret < 0) {
+                     /* Restore back to the original state */
+                     tcpm_set_auto_vbus_discharge_threshold(port, TYPEC_PWR_MODE_PD,
+                                                            port->pps_data.active,
+                                                            port->supply_voltage);
                      port->pps_status = ret;
                      /*
                       * If this was called due to updates to sink
--
Quoted 1 line

2.32.0.272.g935e593368-goog

--
heikki