Skip to contentSkip to conversation

regulator: rt5033: Use linear ranges to map all voltage selection

PATCH In review cy_huang 4 participants 4 messages Jul 6, 2021 – Jul 12, 2021

Subsystems (2)
lore
Share & tools
lore

cy_huang

author
#0 lore raw

PATCH v2 1/1 regulator: rt5033: Use linear ranges to map all voltage selection

From: ChiYuan Huang <[email protected]>

Instead of linear mapping, Use linear range to map all voltage selection.

---
Since v2
- recover the volt number back in rt5033-private.h
- Add the n_voltages from v1 back.

Even though commit 6549c46af855 ("regulator: rt5033: Fix n_voltages settings for BUCK and LDO") can fix the linear mapping to the correct min/max voltage
But there're still non-step ranges for the reserved value.

To use the linear range can fix it for mapping all voltage selection.

---
 drivers/regulator/rt5033-regulator.c | 21 +++++++++++++++------
 include/linux/mfd/rt5033-private.h   |  4 ++--
 2 files changed, 17 insertions(+), 8 deletions(-)
drivers/regulator/rt5033-regulator.c +15 -6
index 0e73116..da4cf5a 100644
@@ -13,6 +13,16 @@
 #include <linux/mfd/rt5033-private.h>
 #include <linux/regulator/of_regulator.h>
 
+static const struct linear_range rt5033_buck_ranges[] = {
+	REGULATOR_LINEAR_RANGE(1000000, 0, 20, 100000),
+	REGULATOR_LINEAR_RANGE(3000000, 21, 31, 0),
+};
+
+static const struct linear_range rt5033_ldo_ranges[] = {
+	REGULATOR_LINEAR_RANGE(1200000, 0, 18, 100000),
+	REGULATOR_LINEAR_RANGE(3000000, 19, 31, 0),
+};
+
 static const struct regulator_ops rt5033_safe_ldo_ops = {
 	.is_enabled		= regulator_is_enabled_regmap,
 	.enable			= regulator_enable_regmap,
@@ -24,8 +34,7 @@ static const struct regulator_ops rt5033_buck_ops = {
 	.is_enabled		= regulator_is_enabled_regmap,
 	.enable			= regulator_enable_regmap,
 	.disable		= regulator_disable_regmap,
-	.list_voltage		= regulator_list_voltage_linear,
-	.map_voltage		= regulator_map_voltage_linear,
+	.list_voltage		= regulator_list_voltage_linear_range,
 	.get_voltage_sel	= regulator_get_voltage_sel_regmap,
 	.set_voltage_sel	= regulator_set_voltage_sel_regmap,
 };
@@ -40,8 +49,8 @@ static const struct regulator_desc rt5033_supported_regulators[] = {
 		.type		= REGULATOR_VOLTAGE,
 		.owner		= THIS_MODULE,
 		.n_voltages	= RT5033_REGULATOR_BUCK_VOLTAGE_STEP_NUM,
-		.min_uV		= RT5033_REGULATOR_BUCK_VOLTAGE_MIN,
-		.uV_step	= RT5033_REGULATOR_BUCK_VOLTAGE_STEP,
+		.linear_ranges	= rt5033_buck_ranges,
+		.n_linear_ranges = ARRAY_SIZE(rt5033_buck_ranges),
 		.enable_reg	= RT5033_REG_CTRL,
 		.enable_mask	= RT5033_CTRL_EN_BUCK_MASK,
 		.vsel_reg	= RT5033_REG_BUCK_CTRL,
@@ -56,8 +65,8 @@ static const struct regulator_desc rt5033_supported_regulators[] = {
 		.type		= REGULATOR_VOLTAGE,
 		.owner		= THIS_MODULE,
 		.n_voltages	= RT5033_REGULATOR_LDO_VOLTAGE_STEP_NUM,
-		.min_uV		= RT5033_REGULATOR_LDO_VOLTAGE_MIN,
-		.uV_step	= RT5033_REGULATOR_LDO_VOLTAGE_STEP,
+		.linear_ranges	= rt5033_ldo_ranges,
+		.n_linear_ranges = ARRAY_SIZE(rt5033_ldo_ranges),
 		.enable_reg	= RT5033_REG_CTRL,
 		.enable_mask	= RT5033_CTRL_EN_LDO_MASK,
 		.vsel_reg	= RT5033_REG_LDO_CTRL,
include/linux/mfd/rt5033-private.h +2 -2
index 40a0c2d..2d1895c 100644
@@ -200,13 +200,13 @@ enum rt5033_reg {
 #define RT5033_REGULATOR_BUCK_VOLTAGE_MIN		1000000U
 #define RT5033_REGULATOR_BUCK_VOLTAGE_MAX		3000000U
 #define RT5033_REGULATOR_BUCK_VOLTAGE_STEP		100000U
-#define RT5033_REGULATOR_BUCK_VOLTAGE_STEP_NUM		21
+#define RT5033_REGULATOR_BUCK_VOLTAGE_STEP_NUM		32
 
 /* RT5033 regulator LDO output voltage uV */
 #define RT5033_REGULATOR_LDO_VOLTAGE_MIN		1200000U
 #define RT5033_REGULATOR_LDO_VOLTAGE_MAX		3000000U
 #define RT5033_REGULATOR_LDO_VOLTAGE_STEP		100000U
-#define RT5033_REGULATOR_LDO_VOLTAGE_STEP_NUM		19
+#define RT5033_REGULATOR_LDO_VOLTAGE_STEP_NUM		32
 
 /* RT5033 regulator SAFE LDO output voltage uV */
 #define RT5033_REGULATOR_SAFE_LDO_VOLTAGE		4900000U
Signature · 1 line
2.7.4
Acked-by on v2 1/1
#2 lore raw
In reply to cy_huang
Quoted 14 lines · cy_huang

From: ChiYuan Huang <[email protected]>

Instead of linear mapping, Use linear range to map all voltage selection.

---
Since v2
- recover the volt number back in rt5033-private.h
- Add the n_voltages from v1 back.

Even though commit 6549c46af855 ("regulator: rt5033: Fix n_voltages settings for BUCK and LDO") can fix the linear mapping to the correct min/max voltage
But there're still non-step ranges for the reserved value.

Quoted 5 lines

To use the linear range can fix it for mapping all voltage selection.

---
 drivers/regulator/rt5033-regulator.c | 21 +++++++++++++++------
 include/linux/mfd/rt5033-private.h   |  4 ++--
Quoted 1 line
 2 files changed, 17 insertions(+), 8 deletions(-)
Signature · 4 lines
Lee Jones [李琼斯]
Senior Technical Lead - Developer Services
Linaro.org │ Open source software for Arm SoCs
Follow Linaro: Facebook | Twitter | Blog
maintainer
#3 lore raw
In reply to cy_huang
Quoted 1 line · cy_huang

Instead of linear mapping, Use linear range to map all voltage selection.

Applied to

https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator.git for-next

Thanks!

[1/1] regulator: rt5033: Use linear ranges to map all voltage selection

      commit: 6eb891cf73bd2ecc877e9916951a19f3e4f3c493

All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent to Linus during the next merge window (or sooner if it is a bug fix), however if problems are discovered then the patch may be dropped or reverted.

You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying to this mail.

Thanks,
Mark