Skip to contentSkip to conversation

drm/i915/dp: dp 2.0 enabling prep work

PATCH Superseded Jani Nikula 3 participants 28 messages Aug 18, 2021 – Aug 20, 2021

Subsystems (4)

v1 of 3 Superseded Latest is v3 →

lore
Share & tools
lore
#0 lore raw

cover drm/i915/dp: dp 2.0 enabling prep work

Start enabling DP 2.0 features. It's not complete, but it's a good start, and should not conflict with anything existing.

Jani Nikula (17):
drm/dp: add DP 2.0 UHBR link rate and bw code conversions drm/dp: use more of the extended receiver cap
drm/dp: add LTTPR DP 2.0 DPCD addresses
drm/dp: add helper for extracting adjust 128b/132b TX FFE preset drm/i915/dp: use actual link rate values in struct link_config_limits drm/i915/dp: read sink UHBR rates
drm/i915/dg2: add TRANS_DP2_CTL register definition drm/i915/dg2: add DG2+ TRANS_DDI_FUNC_CTL DP 2.0 128b/132b mode drm/i915/dg2: add TRANS_DP2_VFREQHIGH and TRANS_DP2_VFREQLOW drm/i915/dg2: add DG2 UHBR source rates
drm/i915/dp: add max data rate calculation for UHBR rates drm/i915/dp: use 128b/132b TPS2 for UHBR+ link rates drm/i915/dp: select 128b/132b channel encoding for UHBR rates drm/i915/dg2: configure TRANS_DP2_CTL for DP 2.0 drm/i915/dg2: use 128b/132b transcoder DDI mode drm/i915/dg2: configure TRANS_DP2_VFREQ{HIGH,LOW} for 128b/132b drm/i915/dg2: update link training for 128b/132b

 drivers/gpu/drm/drm_dp_helper.c               |  42 ++++++-
 drivers/gpu/drm/i915/display/intel_ddi.c      |  61 +++++++---
 drivers/gpu/drm/i915/display/intel_dp.c       | 109 ++++++++++++++----
 drivers/gpu/drm/i915/display/intel_dp.h       |   4 +-
 .../drm/i915/display/intel_dp_link_training.c |  99 +++++++++++-----
 drivers/gpu/drm/i915/display/intel_dp_mst.c   |  17 ++-
 drivers/gpu/drm/i915/i915_reg.h               |  25 +++-
 include/drm/drm_dp_helper.h                   |   6 +
 8 files changed, 289 insertions(+), 74 deletions(-)
Signature · 1 line
2.20.1
#1 lore raw

PATCH 1/17 drm/dp: add DP 2.0 UHBR link rate and bw code conversions

The bw code equals link_rate / 0.27 Gbps only for 8b/10b link rates. Handle DP 2.0 UHBR rates as special cases, though this is not pretty.

---
 drivers/gpu/drm/drm_dp_helper.c | 26 ++++++++++++++++++++++----
 1 file changed, 22 insertions(+), 4 deletions(-)
drivers/gpu/drm/drm_dp_helper.c +22 -4
index 6d0f2c447f3b..9b2a2961fca8 100644
@@ -207,15 +207,33 @@ EXPORT_SYMBOL(drm_dp_lttpr_link_train_channel_eq_delay);
 
 u8 drm_dp_link_rate_to_bw_code(int link_rate)
 {
-	/* Spec says link_bw = link_rate / 0.27Gbps */
-	return link_rate / 27000;
+	switch (link_rate) {
+	case 1000000:
+		return DP_LINK_BW_10;
+	case 1350000:
+		return DP_LINK_BW_13_5;
+	case 2000000:
+		return DP_LINK_BW_20;
+	default:
+		/* Spec says link_bw = link_rate / 0.27Gbps */
+		return link_rate / 27000;
+	}
 }
 EXPORT_SYMBOL(drm_dp_link_rate_to_bw_code);
 
 int drm_dp_bw_code_to_link_rate(u8 link_bw)
 {
-	/* Spec says link_rate = link_bw * 0.27Gbps */
-	return link_bw * 27000;
+	switch (link_bw) {
+	case DP_LINK_BW_10:
+		return 1000000;
+	case DP_LINK_BW_13_5:
+		return 1350000;
+	case DP_LINK_BW_20:
+		return 2000000;
+	default:
+		/* Spec says link_rate = link_bw * 0.27Gbps */
+		return link_bw * 27000;
+	}
 }
 EXPORT_SYMBOL(drm_dp_bw_code_to_link_rate);
 
Signature · 1 line
2.20.1
#2 lore raw

Re: [PATCH 01/17] drm/dp: add DP 2.0 UHBR link rate and bw code conversions

Quoted 3 lines · Jani Nikula

The bw code equals link_rate / 0.27 Gbps only for 8b/10b link rates. Handle DP 2.0 UHBR rates as special cases, though this is not pretty.

Ugh. So if I'm reading the spec right the behaviour of this register now changes dynamically depending on the state of some other bit in another register?

Quoted 51 lines
---
 drivers/gpu/drm/drm_dp_helper.c | 26 ++++++++++++++++++++++----
 1 file changed, 22 insertions(+), 4 deletions(-)
drivers/gpu/drm/drm_dp_helper.c +22 -4
index 6d0f2c447f3b..9b2a2961fca8 100644
@@ -207,15 +207,33 @@ EXPORT_SYMBOL(drm_dp_lttpr_link_train_channel_eq_delay);
 
 u8 drm_dp_link_rate_to_bw_code(int link_rate)
 {
-	/* Spec says link_bw = link_rate / 0.27Gbps */
-	return link_rate / 27000;
+	switch (link_rate) {
+	case 1000000:
+		return DP_LINK_BW_10;
+	case 1350000:
+		return DP_LINK_BW_13_5;
+	case 2000000:
+		return DP_LINK_BW_20;
+	default:
+		/* Spec says link_bw = link_rate / 0.27Gbps */
+		return link_rate / 27000;
+	}
 }
 EXPORT_SYMBOL(drm_dp_link_rate_to_bw_code);
 
 int drm_dp_bw_code_to_link_rate(u8 link_bw)
 {
-	/* Spec says link_rate = link_bw * 0.27Gbps */
-	return link_bw * 27000;
+	switch (link_bw) {
+	case DP_LINK_BW_10:
+		return 1000000;
+	case DP_LINK_BW_13_5:
+		return 1350000;
+	case DP_LINK_BW_20:
+		return 2000000;
+	default:
+		/* Spec says link_rate = link_bw * 0.27Gbps */
+		return link_bw * 27000;
+	}
 }
 EXPORT_SYMBOL(drm_dp_bw_code_to_link_rate);
 
Signature · 1 line
2.20.1
Signature · 2 lines
Ville Syrjälä
Intel
#3 lore raw

PATCH 2/17 drm/dp: use more of the extended receiver cap

In reply to Jani Nikula

Extend the use of extended receiver cap at 0x2200 to cover MAIN_LINK_CHANNEL_CODING_CAP in 0x2206, in case an implementation hides the DP 2.0 128b/132b channel encoding cap.

---
 drivers/gpu/drm/drm_dp_helper.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/gpu/drm/drm_dp_helper.c +1 -1
index 9b2a2961fca8..9389f92cb944 100644
@@ -608,7 +608,7 @@ static u8 drm_dp_downstream_port_count(const u8 dpcd[DP_RECEIVER_CAP_SIZE])
 static int drm_dp_read_extended_dpcd_caps(struct drm_dp_aux *aux,
 					  u8 dpcd[DP_RECEIVER_CAP_SIZE])
 {
-	u8 dpcd_ext[6];
+	u8 dpcd_ext[DP_MAIN_LINK_CHANNEL_CODING + 1];
 	int ret;
 
 	/*
Signature · 1 line
2.20.1
#4 lore raw

PATCH 3/17 drm/dp: add LTTPR DP 2.0 DPCD addresses

In reply to Jani Nikula

DP 2.0 brings some new DPCD addresses for PHY repeaters.

---
 include/drm/drm_dp_helper.h | 4 ++++
 1 file changed, 4 insertions(+)
include/drm/drm_dp_helper.h +4 -0
index 1d5b3dbb6e56..f3a61341011d 100644
@@ -1319,6 +1319,10 @@ struct drm_panel;
 #define DP_MAX_LANE_COUNT_PHY_REPEATER			    0xf0004 /* 1.4a */
 #define DP_Repeater_FEC_CAPABILITY			    0xf0004 /* 1.4 */
 #define DP_PHY_REPEATER_EXTENDED_WAIT_TIMEOUT		    0xf0005 /* 1.4a */
+#define DP_MAIN_LINK_CHANNEL_CODING_PHY_REPEATER	    0xf0006 /* 2.0 */
+# define DP_PHY_REPEATER_128B132B_SUPPORTED		    (1 << 0)
+/* See DP_128B132B_SUPPORTED_LINK_RATES for values */
+#define DP_PHY_REPEATER_128B132B_RATES			    0xf0007 /* 2.0 */
 
 enum drm_dp_phy {
 	DP_PHY_DPRX,
Signature · 1 line
2.20.1
#5 lore raw

PATCH 4/17 drm/dp: add helper for extracting adjust 128b/132b TX FFE preset

In reply to Jani Nikula

The DP 2.0 128b/132b channel coding uses TX FFE presets instead of vswing and pre-emphasis.

---
 drivers/gpu/drm/drm_dp_helper.c | 14 ++++++++++++++
 include/drm/drm_dp_helper.h     |  2 ++
 2 files changed, 16 insertions(+)
drivers/gpu/drm/drm_dp_helper.c +14 -0
index 9389f92cb944..2843238a78e6 100644
@@ -130,6 +130,20 @@ u8 drm_dp_get_adjust_request_pre_emphasis(const u8 link_status[DP_LINK_STATUS_SI
 }
 EXPORT_SYMBOL(drm_dp_get_adjust_request_pre_emphasis);
 
+/* DP 2.0 128b/132b */
+u8 drm_dp_get_adjust_tx_ffe_preset(const u8 link_status[DP_LINK_STATUS_SIZE],
+				   int lane)
+{
+	int i = DP_ADJUST_REQUEST_LANE0_1 + (lane >> 1);
+	int s = ((lane & 1) ?
+		 DP_ADJUST_TX_FFE_PRESET_LANE1_SHIFT :
+		 DP_ADJUST_TX_FFE_PRESET_LANE0_SHIFT);
+	u8 l = dp_link_status(link_status, i);
+
+	return (l >> s) & 0xf;
+}
+EXPORT_SYMBOL(drm_dp_get_adjust_tx_ffe_preset);
+
 u8 drm_dp_get_adjust_request_post_cursor(const u8 link_status[DP_LINK_STATUS_SIZE],
 					 unsigned int lane)
 {
include/drm/drm_dp_helper.h +2 -0
index f3a61341011d..3ee0b3ffb8a5 100644
@@ -1494,6 +1494,8 @@ u8 drm_dp_get_adjust_request_voltage(const u8 link_status[DP_LINK_STATUS_SIZE],
 				     int lane);
 u8 drm_dp_get_adjust_request_pre_emphasis(const u8 link_status[DP_LINK_STATUS_SIZE],
 					  int lane);
+u8 drm_dp_get_adjust_tx_ffe_preset(const u8 link_status[DP_LINK_STATUS_SIZE],
+				   int lane);
 u8 drm_dp_get_adjust_request_post_cursor(const u8 link_status[DP_LINK_STATUS_SIZE],
 					 unsigned int lane);
 
Signature · 1 line
2.20.1
Reviewed-by on v1 4/17
#6 lore raw

Re: [PATCH 04/17] drm/dp: add helper for extracting adjust 128b/132b TX FFE preset

Quoted 5 lines · Jani Nikula

The DP 2.0 128b/132b channel coding uses TX FFE presets instead of vswing and pre-emphasis.

Quoted 45 lines
---
 drivers/gpu/drm/drm_dp_helper.c | 14 ++++++++++++++
 include/drm/drm_dp_helper.h     |  2 ++
 2 files changed, 16 insertions(+)
drivers/gpu/drm/drm_dp_helper.c +14 -0
index 9389f92cb944..2843238a78e6 100644
@@ -130,6 +130,20 @@ u8 drm_dp_get_adjust_request_pre_emphasis(const u8 link_status[DP_LINK_STATUS_SI
 }
 EXPORT_SYMBOL(drm_dp_get_adjust_request_pre_emphasis);
 
+/* DP 2.0 128b/132b */
+u8 drm_dp_get_adjust_tx_ffe_preset(const u8 link_status[DP_LINK_STATUS_SIZE],
+				   int lane)
+{
+	int i = DP_ADJUST_REQUEST_LANE0_1 + (lane >> 1);
+	int s = ((lane & 1) ?
+		 DP_ADJUST_TX_FFE_PRESET_LANE1_SHIFT :
+		 DP_ADJUST_TX_FFE_PRESET_LANE0_SHIFT);
+	u8 l = dp_link_status(link_status, i);
+
+	return (l >> s) & 0xf;
+}
+EXPORT_SYMBOL(drm_dp_get_adjust_tx_ffe_preset);
+
 u8 drm_dp_get_adjust_request_post_cursor(const u8 link_status[DP_LINK_STATUS_SIZE],
 					 unsigned int lane)
 {
include/drm/drm_dp_helper.h +2 -0
index f3a61341011d..3ee0b3ffb8a5 100644
@@ -1494,6 +1494,8 @@ u8 drm_dp_get_adjust_request_voltage(const u8 link_status[DP_LINK_STATUS_SIZE],
 				     int lane);
 u8 drm_dp_get_adjust_request_pre_emphasis(const u8 link_status[DP_LINK_STATUS_SIZE],
 					  int lane);
+u8 drm_dp_get_adjust_tx_ffe_preset(const u8 link_status[DP_LINK_STATUS_SIZE],
+				   int lane);
 u8 drm_dp_get_adjust_request_post_cursor(const u8 link_status[DP_LINK_STATUS_SIZE],
 					 unsigned int lane);
 
Signature · 1 line
2.20.1
Signature · 2 lines
Ville Syrjälä
Intel
#7 lore raw

PATCH 5/17 drm/i915/dp: use actual link rate values in struct link_config_limits

In reply to Jani Nikula

The MST code uses actual link rates in the limits struct, while the DP code in general uses indexes to the ->common_rates[] array. Fix the confusion by using actual link rate values everywhere. This is a better abstraction than some obscure index.

Rename the struct members while at it to ensure all the places are covered.

---
 drivers/gpu/drm/i915/display/intel_dp.c     | 30 ++++++++++++---------
 drivers/gpu/drm/i915/display/intel_dp.h     |  2 +-
 drivers/gpu/drm/i915/display/intel_dp_mst.c |  6 ++---
 3 files changed, 21 insertions(+), 17 deletions(-)
drivers/gpu/drm/i915/display/intel_dp.c +17 -13
index 75d4ebc66941..d273b3848785 100644
@@ -1044,7 +1044,8 @@ intel_dp_adjust_compliance_config(struct intel_dp *intel_dp,
 						    intel_dp->num_common_rates,
 						    intel_dp->compliance.test_link_rate);
 			if (index >= 0)
-				limits->min_clock = limits->max_clock = index;
+				limits->min_rate = limits->max_rate =
+					intel_dp->compliance.test_link_rate;
 			limits->min_lane_count = limits->max_lane_count =
 				intel_dp->compliance.test_lane_count;
 		}
@@ -1058,8 +1059,8 @@ intel_dp_compute_link_config_wide(struct intel_dp *intel_dp,
 				  const struct link_config_limits *limits)
 {
 	struct drm_display_mode *adjusted_mode = &pipe_config->hw.adjusted_mode;
-	int bpp, clock, lane_count;
-	int mode_rate, link_clock, link_avail;
+	int bpp, i, lane_count;
+	int mode_rate, link_rate, link_avail;
 
 	for (bpp = limits->max_bpp; bpp >= limits->min_bpp; bpp -= 2 * 3) {
 		int output_bpp = intel_dp_output_bpp(pipe_config->output_format, bpp);
@@ -1067,18 +1068,22 @@ intel_dp_compute_link_config_wide(struct intel_dp *intel_dp,
 		mode_rate = intel_dp_link_required(adjusted_mode->crtc_clock,
 						   output_bpp);
 
-		for (clock = limits->min_clock; clock <= limits->max_clock; clock++) {
+		for (i = 0; i < intel_dp->num_common_rates; i++) {
+			link_rate = intel_dp->common_rates[i];
+			if (link_rate < limits->min_rate ||
+			    link_rate > limits->max_rate)
+				continue;
+
 			for (lane_count = limits->min_lane_count;
 			     lane_count <= limits->max_lane_count;
 			     lane_count <<= 1) {
-				link_clock = intel_dp->common_rates[clock];
-				link_avail = intel_dp_max_data_rate(link_clock,
+				link_avail = intel_dp_max_data_rate(link_rate,
 								    lane_count);
 
 				if (mode_rate <= link_avail) {
 					pipe_config->lane_count = lane_count;
 					pipe_config->pipe_bpp = bpp;
-					pipe_config->port_clock = link_clock;
+					pipe_config->port_clock = link_rate;
 
 					return 0;
 				}
@@ -1212,7 +1217,7 @@ static int intel_dp_dsc_compute_config(struct intel_dp *intel_dp,
 	 * with DSC enabled for the requested mode.
 	 */
 	pipe_config->pipe_bpp = pipe_bpp;
-	pipe_config->port_clock = intel_dp->common_rates[limits->max_clock];
+	pipe_config->port_clock = limits->max_rate;
 	pipe_config->lane_count = limits->max_lane_count;
 
 	if (intel_dp_is_edp(intel_dp)) {
@@ -1321,8 +1326,8 @@ intel_dp_compute_link_config(struct intel_encoder *encoder,
 	/* No common link rates between source and sink */
 	drm_WARN_ON(encoder->base.dev, common_len <= 0);
 
-	limits.min_clock = 0;
-	limits.max_clock = common_len - 1;
+	limits.min_rate = intel_dp->common_rates[0];
+	limits.max_rate = intel_dp->common_rates[common_len - 1];
 
 	limits.min_lane_count = 1;
 	limits.max_lane_count = intel_dp_max_lane_count(intel_dp);
@@ -1340,15 +1345,14 @@ intel_dp_compute_link_config(struct intel_encoder *encoder,
 		 * values correspond to the native resolution of the panel.
 		 */
 		limits.min_lane_count = limits.max_lane_count;
-		limits.min_clock = limits.max_clock;
+		limits.min_rate = limits.max_rate;
 	}
 
 	intel_dp_adjust_compliance_config(intel_dp, pipe_config, &limits);
 
 	drm_dbg_kms(&i915->drm, "DP link computation with max lane count %i "
 		    "max rate %d max bpp %d pixel clock %iKHz\n",
-		    limits.max_lane_count,
-		    intel_dp->common_rates[limits.max_clock],
+		    limits.max_lane_count, limits.max_rate,
 		    limits.max_bpp, adjusted_mode->crtc_clock);
 
 	if ((adjusted_mode->crtc_clock > i915->max_dotclk_freq ||
drivers/gpu/drm/i915/display/intel_dp.h +1 -1
index 680631b5b437..1345d588fc6d 100644
@@ -26,7 +26,7 @@ struct intel_dp;
 struct intel_encoder;
 
 struct link_config_limits {
-	int min_clock, max_clock;
+	int min_rate, max_rate;
 	int min_lane_count, max_lane_count;
 	int min_bpp, max_bpp;
 };
drivers/gpu/drm/i915/display/intel_dp_mst.c +3 -3
index 9859c0334ebc..d104441344c0 100644
@@ -61,7 +61,7 @@ static int intel_dp_mst_compute_link_config(struct intel_encoder *encoder,
 	int bpp, slots = -EINVAL;
 
 	crtc_state->lane_count = limits->max_lane_count;
-	crtc_state->port_clock = limits->max_clock;
+	crtc_state->port_clock = limits->max_rate;
 
 	for (bpp = limits->max_bpp; bpp >= limits->min_bpp; bpp -= 2 * 3) {
 		crtc_state->pipe_bpp = bpp;
@@ -131,8 +131,8 @@ static int intel_dp_mst_compute_config(struct intel_encoder *encoder,
 	 * for MST we always configure max link bw - the spec doesn't
 	 * seem to suggest we should do otherwise.
 	 */
-	limits.min_clock =
-	limits.max_clock = intel_dp_max_link_rate(intel_dp);
+	limits.min_rate =
+	limits.max_rate = intel_dp_max_link_rate(intel_dp);
 
 	limits.min_lane_count =
 	limits.max_lane_count = intel_dp_max_lane_count(intel_dp);
Signature · 1 line
2.20.1
Reviewed-by on v1 5/17
#8 lore raw

Re: [Intel-gfx] [PATCH 05/17] drm/i915/dp: use actual link rate values in struct link_config_limits

Quoted 9 lines · Jani Nikula

The MST code uses actual link rates in the limits struct, while the DP code in general uses indexes to the ->common_rates[] array. Fix the confusion by using actual link rate values everywhere. This is a better abstraction than some obscure index.

Rename the struct members while at it to ensure all the places are covered.

Quoted 135 lines
---
 drivers/gpu/drm/i915/display/intel_dp.c     | 30 ++++++++++++---------
 drivers/gpu/drm/i915/display/intel_dp.h     |  2 +-
 drivers/gpu/drm/i915/display/intel_dp_mst.c |  6 ++---
 3 files changed, 21 insertions(+), 17 deletions(-)
drivers/gpu/drm/i915/display/intel_dp.c +17 -13
index 75d4ebc66941..d273b3848785 100644
@@ -1044,7 +1044,8 @@ intel_dp_adjust_compliance_config(struct intel_dp *intel_dp,
 						    intel_dp->num_common_rates,
 						    intel_dp->compliance.test_link_rate);
 			if (index >= 0)
-				limits->min_clock = limits->max_clock = index;
+				limits->min_rate = limits->max_rate =
+					intel_dp->compliance.test_link_rate;
 			limits->min_lane_count = limits->max_lane_count =
 				intel_dp->compliance.test_lane_count;
 		}
@@ -1058,8 +1059,8 @@ intel_dp_compute_link_config_wide(struct intel_dp *intel_dp,
 				  const struct link_config_limits *limits)
 {
 	struct drm_display_mode *adjusted_mode = &pipe_config->hw.adjusted_mode;
-	int bpp, clock, lane_count;
-	int mode_rate, link_clock, link_avail;
+	int bpp, i, lane_count;
+	int mode_rate, link_rate, link_avail;
 
 	for (bpp = limits->max_bpp; bpp >= limits->min_bpp; bpp -= 2 * 3) {
 		int output_bpp = intel_dp_output_bpp(pipe_config->output_format, bpp);
@@ -1067,18 +1068,22 @@ intel_dp_compute_link_config_wide(struct intel_dp *intel_dp,
 		mode_rate = intel_dp_link_required(adjusted_mode->crtc_clock,
 						   output_bpp);
 
-		for (clock = limits->min_clock; clock <= limits->max_clock; clock++) {
+		for (i = 0; i < intel_dp->num_common_rates; i++) {
+			link_rate = intel_dp->common_rates[i];
+			if (link_rate < limits->min_rate ||
+			    link_rate > limits->max_rate)
+				continue;
+
 			for (lane_count = limits->min_lane_count;
 			     lane_count <= limits->max_lane_count;
 			     lane_count <<= 1) {
-				link_clock = intel_dp->common_rates[clock];
-				link_avail = intel_dp_max_data_rate(link_clock,
+				link_avail = intel_dp_max_data_rate(link_rate,
 								    lane_count);
 
 				if (mode_rate <= link_avail) {
 					pipe_config->lane_count = lane_count;
 					pipe_config->pipe_bpp = bpp;
-					pipe_config->port_clock = link_clock;
+					pipe_config->port_clock = link_rate;
 
 					return 0;
 				}
@@ -1212,7 +1217,7 @@ static int intel_dp_dsc_compute_config(struct intel_dp *intel_dp,
 	 * with DSC enabled for the requested mode.
 	 */
 	pipe_config->pipe_bpp = pipe_bpp;
-	pipe_config->port_clock = intel_dp->common_rates[limits->max_clock];
+	pipe_config->port_clock = limits->max_rate;
 	pipe_config->lane_count = limits->max_lane_count;
 
 	if (intel_dp_is_edp(intel_dp)) {
@@ -1321,8 +1326,8 @@ intel_dp_compute_link_config(struct intel_encoder *encoder,
 	/* No common link rates between source and sink */
 	drm_WARN_ON(encoder->base.dev, common_len <= 0);
 
-	limits.min_clock = 0;
-	limits.max_clock = common_len - 1;
+	limits.min_rate = intel_dp->common_rates[0];
+	limits.max_rate = intel_dp->common_rates[common_len - 1];
 
 	limits.min_lane_count = 1;
 	limits.max_lane_count = intel_dp_max_lane_count(intel_dp);
@@ -1340,15 +1345,14 @@ intel_dp_compute_link_config(struct intel_encoder *encoder,
 		 * values correspond to the native resolution of the panel.
 		 */
 		limits.min_lane_count = limits.max_lane_count;
-		limits.min_clock = limits.max_clock;
+		limits.min_rate = limits.max_rate;
 	}
 
 	intel_dp_adjust_compliance_config(intel_dp, pipe_config, &limits);
 
 	drm_dbg_kms(&i915->drm, "DP link computation with max lane count %i "
 		    "max rate %d max bpp %d pixel clock %iKHz\n",
-		    limits.max_lane_count,
-		    intel_dp->common_rates[limits.max_clock],
+		    limits.max_lane_count, limits.max_rate,
 		    limits.max_bpp, adjusted_mode->crtc_clock);
 
 	if ((adjusted_mode->crtc_clock > i915->max_dotclk_freq ||
drivers/gpu/drm/i915/display/intel_dp.h +1 -1
index 680631b5b437..1345d588fc6d 100644
@@ -26,7 +26,7 @@ struct intel_dp;
 struct intel_encoder;
 
 struct link_config_limits {
-	int min_clock, max_clock;
+	int min_rate, max_rate;
 	int min_lane_count, max_lane_count;
 	int min_bpp, max_bpp;
 };
drivers/gpu/drm/i915/display/intel_dp_mst.c +3 -3
index 9859c0334ebc..d104441344c0 100644
@@ -61,7 +61,7 @@ static int intel_dp_mst_compute_link_config(struct intel_encoder *encoder,
 	int bpp, slots = -EINVAL;
 
 	crtc_state->lane_count = limits->max_lane_count;
-	crtc_state->port_clock = limits->max_clock;
+	crtc_state->port_clock = limits->max_rate;
 
 	for (bpp = limits->max_bpp; bpp >= limits->min_bpp; bpp -= 2 * 3) {
 		crtc_state->pipe_bpp = bpp;
@@ -131,8 +131,8 @@ static int intel_dp_mst_compute_config(struct intel_encoder *encoder,
 	 * for MST we always configure max link bw - the spec doesn't
 	 * seem to suggest we should do otherwise.
 	 */
-	limits.min_clock =
-	limits.max_clock = intel_dp_max_link_rate(intel_dp);
+	limits.min_rate =
+	limits.max_rate = intel_dp_max_link_rate(intel_dp);
 
 	limits.min_lane_count =
 	limits.max_lane_count = intel_dp_max_lane_count(intel_dp);
Signature · 1 line
2.20.1
Signature · 2 lines
Ville Syrjälä
Intel
#9 lore raw

PATCH 6/17 drm/i915/dp: read sink UHBR rates

In reply to Jani Nikula

See if sink supports DP 2.0 128b/132b channel encoding, and update sink rates accordingly.

FIXME: Also take LTTPR 128b/132b into account.

---
 drivers/gpu/drm/i915/display/intel_dp.c | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)
drivers/gpu/drm/i915/display/intel_dp.c +18 -0
index d273b3848785..079b5b37b85a 100644
@@ -141,6 +141,24 @@ static void intel_dp_set_sink_rates(struct intel_dp *intel_dp)
 		intel_dp->sink_rates[i] = dp_rates[i];
 	}
 
+	/*
+	 * Sink rates for 128b/132b. If set, sink should support all 8b/10b
+	 * rates and 10 Gbps.
+	 */
+	if (intel_dp->dpcd[DP_MAIN_LINK_CHANNEL_CODING] & DP_CAP_ANSI_128B132B) {
+		u8 uhbr_rates = 0;
+
+		drm_dp_dpcd_readb(&intel_dp->aux,
+				  DP_128B132B_SUPPORTED_LINK_RATES, &uhbr_rates);
+
+		if (uhbr_rates & DP_UHBR10)
+			intel_dp->sink_rates[i++] = 1000000;
+		if (uhbr_rates & DP_UHBR13_5)
+			intel_dp->sink_rates[i++] = 1350000;
+		if (uhbr_rates & DP_UHBR20)
+			intel_dp->sink_rates[i++] = 2000000;
+	}
+
 	intel_dp->num_sink_rates = i;
 }
 
Signature · 1 line
2.20.1
Reviewed-by on v1 6/17
#10 lore raw

Re: [Intel-gfx] [PATCH 06/17] drm/i915/dp: read sink UHBR rates

Quoted 25 lines · Jani Nikula

See if sink supports DP 2.0 128b/132b channel encoding, and update sink rates accordingly.

FIXME: Also take LTTPR 128b/132b into account.

---
 drivers/gpu/drm/i915/display/intel_dp.c | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)
drivers/gpu/drm/i915/display/intel_dp.c +6 -0
index d273b3848785..079b5b37b85a 100644
@@ -141,6 +141,24 @@ static void intel_dp_set_sink_rates(struct intel_dp *intel_dp)
 		intel_dp->sink_rates[i] = dp_rates[i];
 	}
 
+	/*
+	 * Sink rates for 128b/132b. If set, sink should support all 8b/10b
+	 * rates and 10 Gbps.
+	 */
+	if (intel_dp->dpcd[DP_MAIN_LINK_CHANNEL_CODING] & DP_CAP_ANSI_128B132B) {
+		u8 uhbr_rates = 0;

drivers/gpu/drm/i915/display/intel_dp.c static void intel_dp_set_sink_rates(struct intel_dp *intel_dp) · line 159

Quoted 10 lines
drivers/gpu/drm/i915/display/intel_dp.c +10 -0
+
+		drm_dp_dpcd_readb(&intel_dp->aux,
+				  DP_128B132B_SUPPORTED_LINK_RATES, &uhbr_rates);
+
+		if (uhbr_rates & DP_UHBR10)
+			intel_dp->sink_rates[i++] = 1000000;
+		if (uhbr_rates & DP_UHBR13_5)
+			intel_dp->sink_rates[i++] = 1350000;
+		if (uhbr_rates & DP_UHBR20)
+			intel_dp->sink_rates[i++] = 2000000;

OK, so the max link rate register isn't supposed to report the new magic UHBR BW values it seems. That makes life a bit easier.

Maybe toss in a
BUILD_BUG_ON(ARRAY_SIZE(sink_rates) >= ARRAY_SIZE(dp_rates)+3); or something to remind people that we are dealing with a fixed size array here?

Quoted 7 lines
drivers/gpu/drm/i915/display/intel_dp.c +2 -0
+	}
+
 	intel_dp->num_sink_rates = i;
 }
 
Signature · 1 line
2.20.1
Signature · 2 lines
Ville Syrjälä
Intel
#11 lore raw

PATCH 7/17 drm/i915/dg2: add TRANS_DP2_CTL register definition

In reply to Jani Nikula

This register controls the DP 2.0 datapath.

Bspec: 69967

---
 drivers/gpu/drm/i915/i915_reg.h | 9 +++++++++
 1 file changed, 9 insertions(+)
drivers/gpu/drm/i915/i915_reg.h +9 -0
index 72dd3a6d205d..f9d4e908bf93 100644
@@ -9099,6 +9099,15 @@ enum {
 #define  TRANS_DP_HSYNC_ACTIVE_LOW	0
 #define  TRANS_DP_SYNC_MASK	(3 << 3)
 
+#define _TRANS_DP2_CTL_A			0x600a0
+#define _TRANS_DP2_CTL_B			0x610a0
+#define _TRANS_DP2_CTL_C			0x620a0
+#define _TRANS_DP2_CTL_D			0x630a0
+#define TRANS_DP2_CTL(trans)			_MMIO_TRANS(trans, _TRANS_DP2_CTL_A, _TRANS_DP2_CTL_B)
+#define  TRANS_DP2_128B132B_CHANNEL_CODING	REG_BIT(31)
+#define  TRANS_DP2_PANEL_REPLAY_ENABLE		REG_BIT(30)
+#define  TRANS_DP2_DEBUG_ENABLE			REG_BIT(23)
+
 /* SNB eDP training params */
 /* SNB A-stepping */
 #define  EDP_LINK_TRAIN_400MV_0DB_SNB_A		(0x38 << 22)
Signature · 1 line
2.20.1
#12 lore raw

PATCH 8/17 drm/i915/dg2: add DG2+ TRANS_DDI_FUNC_CTL DP 2.0 128b/132b mode

In reply to Jani Nikula

Unfortunately, the DP 2.0 128b/132b DDI mode selection in the register conflicts with FDI. Since we have to deal with both meanings in the same code, for different platforms, clarify the macro name so we don't forget.

Bspec: 50493

---
 drivers/gpu/drm/i915/display/intel_ddi.c | 6 +++---
 drivers/gpu/drm/i915/i915_reg.h          | 2 +-
 2 files changed, 4 insertions(+), 4 deletions(-)
drivers/gpu/drm/i915/display/intel_ddi.c +3 -3
index 1ef7a65feb66..203a54f905f6 100644
@@ -488,7 +488,7 @@ intel_ddi_transcoder_func_reg_val_get(struct intel_encoder *encoder,
 		if (crtc_state->hdmi_high_tmds_clock_ratio)
 			temp |= TRANS_DDI_HIGH_TMDS_CHAR_RATE;
 	} else if (intel_crtc_has_type(crtc_state, INTEL_OUTPUT_ANALOG)) {
-		temp |= TRANS_DDI_MODE_SELECT_FDI;
+		temp |= TRANS_DDI_MODE_SELECT_FDI_OR_128B132B;
 		temp |= (crtc_state->fdi_lanes - 1) << 1;
 	} else if (intel_crtc_has_type(crtc_state, INTEL_OUTPUT_DP_MST)) {
 		temp |= TRANS_DDI_MODE_SELECT_DP_MST;
@@ -678,7 +678,7 @@ bool intel_ddi_connector_get_hw_state(struct intel_connector *intel_connector)
 		ret = false;
 		break;
 
-	case TRANS_DDI_MODE_SELECT_FDI:
+	case TRANS_DDI_MODE_SELECT_FDI_OR_128B132B:
 		ret = type == DRM_MODE_CONNECTOR_VGA;
 		break;
 
@@ -3557,7 +3557,7 @@ static void intel_ddi_read_func_ctl(struct intel_encoder *encoder,
 		pipe_config->output_types |= BIT(INTEL_OUTPUT_HDMI);
 		pipe_config->lane_count = 4;
 		break;
-	case TRANS_DDI_MODE_SELECT_FDI:
+	case TRANS_DDI_MODE_SELECT_FDI_OR_128B132B:
 		pipe_config->output_types |= BIT(INTEL_OUTPUT_ANALOG);
 		break;
 	case TRANS_DDI_MODE_SELECT_DP_SST:
drivers/gpu/drm/i915/i915_reg.h +1 -1
index f9d4e908bf93..18083ae8a877 100644
@@ -10167,7 +10167,7 @@ enum skl_power_gate {
 #define  TRANS_DDI_MODE_SELECT_DVI	(1 << 24)
 #define  TRANS_DDI_MODE_SELECT_DP_SST	(2 << 24)
 #define  TRANS_DDI_MODE_SELECT_DP_MST	(3 << 24)
-#define  TRANS_DDI_MODE_SELECT_FDI	(4 << 24)
+#define  TRANS_DDI_MODE_SELECT_FDI_OR_128B132B	(4 << 24)
 #define  TRANS_DDI_BPC_MASK		(7 << 20)
 #define  TRANS_DDI_BPC_8		(0 << 20)
 #define  TRANS_DDI_BPC_10		(1 << 20)
Signature · 1 line
2.20.1
#13 lore raw

PATCH 9/17 drm/i915/dg2: add TRANS_DP2_VFREQHIGH and TRANS_DP2_VFREQLOW

In reply to Jani Nikula

Add the registers for specifying the lower and higher 24 bits of the DP 2.0 pixel clock frequency in Hz.

Bspec: 53326

---
 drivers/gpu/drm/i915/i915_reg.h | 14 ++++++++++++++
 1 file changed, 14 insertions(+)
drivers/gpu/drm/i915/i915_reg.h +14 -0
index 18083ae8a877..f377044fb9ac 100644
@@ -9108,6 +9108,20 @@ enum {
 #define  TRANS_DP2_PANEL_REPLAY_ENABLE		REG_BIT(30)
 #define  TRANS_DP2_DEBUG_ENABLE			REG_BIT(23)
 
+#define _TRANS_DP2_VFREQHIGH_A			0x600a4
+#define _TRANS_DP2_VFREQHIGH_B			0x610a4
+#define _TRANS_DP2_VFREQHIGH_C			0x620a4
+#define _TRANS_DP2_VFREQHIGH_D			0x630a4
+#define TRANS_DP2_VFREQHIGH(trans)		_MMIO_TRANS(trans, _TRANS_DP2_VFREQHIGH_A, _TRANS_DP2_VFREQHIGH_B)
+#define  TRANS_DP2_VFREQ_PIXEL_CLOCK_MASK	REG_GENMASK(31, 8)
+#define  TRANS_DP2_VFREQ_PIXEL_CLOCK(clk_hz)	REG_FIELD_PREP(TRANS_DP2_VFREQ_PIXEL_CLOCK_MASK, (clk_hz))
+
+#define _TRANS_DP2_VFREQLOW_A			0x600a8
+#define _TRANS_DP2_VFREQLOW_B			0x610a8
+#define _TRANS_DP2_VFREQLOW_C			0x620a8
+#define _TRANS_DP2_VFREQLOW_D			0x630a8
+#define TRANS_DP2_VFREQLOW(trans)		_MMIO_TRANS(trans, _TRANS_DP2_VFREQLOW_A, _TRANS_DP2_VFREQLOW_B)
+
 /* SNB eDP training params */
 /* SNB A-stepping */
 #define  EDP_LINK_TRAIN_400MV_0DB_SNB_A		(0x38 << 22)
Signature · 1 line
2.20.1
#14 lore raw

PATCH 10/17 drm/i915/dg2: add DG2 UHBR source rates

In reply to Jani Nikula

DG2 supports DP 2.0 UHBR and 128b/132b channel encoding.

Bspec: 53657, 54034

---
 drivers/gpu/drm/i915/display/intel_dp.c | 10 +++++++++-
 1 file changed, 9 insertions(+), 1 deletion(-)
drivers/gpu/drm/i915/display/intel_dp.c +9 -1
index 079b5b37b85a..38d69e3d55ff 100644
@@ -240,6 +240,11 @@ bool intel_dp_can_bigjoiner(struct intel_dp *intel_dp)
 		 encoder->port != PORT_A);
 }
 
+static int dg2_max_source_rate(struct intel_dp *intel_dp)
+{
+	return intel_dp_is_edp(intel_dp) ? 810000 : 1350000;
+}
+
 static int icl_max_source_rate(struct intel_dp *intel_dp)
 {
 	struct intel_digital_port *dig_port = dp_to_dig_port(intel_dp);
@@ -266,7 +271,8 @@ intel_dp_set_source_rates(struct intel_dp *intel_dp)
 {
 	/* The values must be in increasing order */
 	static const int icl_rates[] = {
-		162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000
+		162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000,
+		1000000, 1350000,
 	};
 	static const int bxt_rates[] = {
 		162000, 216000, 243000, 270000, 324000, 432000, 540000
@@ -293,6 +299,8 @@ intel_dp_set_source_rates(struct intel_dp *intel_dp)
 	if (DISPLAY_VER(dev_priv) >= 11) {
 		source_rates = icl_rates;
 		size = ARRAY_SIZE(icl_rates);
+		if (IS_DG2(dev_priv))
+			max_rate = dg2_max_source_rate(intel_dp);
 		if (IS_JSL_EHL(dev_priv))
 			max_rate = ehl_max_source_rate(intel_dp);
 		else
Signature · 1 line
2.20.1
#15 lore raw

PATCH 11/17 drm/i915/dp: add max data rate calculation for UHBR rates

In reply to Jani Nikula

DP 2.0 UHBR link rates always use 128b/132b channel encoding, which has a different data bandwidth efficiency from 8b/10b. The computation is slightly convoluted due to the units we use; this is all explained in the added comment.

v2: Clarified comment (Manasi)

---
 drivers/gpu/drm/i915/display/intel_dp.c | 51 ++++++++++++++++++++++---
 drivers/gpu/drm/i915/display/intel_dp.h |  2 +-
 2 files changed, 46 insertions(+), 7 deletions(-)
drivers/gpu/drm/i915/display/intel_dp.c +45 -6
index 38d69e3d55ff..8e42c30b459c 100644
@@ -210,6 +210,10 @@ int intel_dp_max_lane_count(struct intel_dp *intel_dp)
 	return intel_dp->max_link_lane_count;
 }
 
+/*
+ * The required data bandwidth for a mode with given pixel clock and bpp. This
+ * is the required net bandwidth independent of the data bandwidth efficiency.
+ */
 int
 intel_dp_link_required(int pixel_clock, int bpp)
 {
@@ -217,16 +221,51 @@ intel_dp_link_required(int pixel_clock, int bpp)
 	return DIV_ROUND_UP(pixel_clock * bpp, 8);
 }
 
+/*
+ * Given a link rate and lanes, get the data bandwidth.
+ *
+ * Data bandwidth is the actual payload rate, which depends on the data
+ * bandwidth efficiency and the link rate.
+ *
+ * For 8b/10b channel encoding, SST and non-FEC, the data bandwidth efficiency
+ * is 80%. For example, for a 1.62 Gbps link, 1.62*10^9 bps * 0.80 * (1/8) =
+ * 162000 kBps. With 8-bit symbols, we have 162000 kHz symbol clock. Just by
+ * coincidence, the port clock in kHz matches the data bandwidth in kBps, and
+ * they equal the link bit rate in Gbps multiplied by 100000. (Note that this no
+ * longer holds for data bandwidth as soon as FEC or MST is taken into account!)
+ *
+ * For 128b/132b channel encoding, the data bandwidth efficiency is 96.71%. For
+ * example, for a 10 Gbps link, 10*10^9 bps * 0.9671 * (1/8) = 1208875
+ * kBps. With 32-bit symbols, we have 312500 kHz symbol clock. The value 1000000
+ * does not match the symbol clock, the port clock (not even if you think in
+ * terms of a byte clock), nor the data bandwidth. It only matches the link bit
+ * rate in units of 10000 bps.
+ */
 int
-intel_dp_max_data_rate(int max_link_clock, int max_lanes)
+intel_dp_max_data_rate(int max_link_rate, int max_lanes)
 {
-	/* max_link_clock is the link symbol clock (LS_Clk) in kHz and not the
-	 * link rate that is generally expressed in Gbps. Since, 8 bits of data
-	 * is transmitted every LS_Clk per lane, there is no need to account for
-	 * the channel encoding that is done in the PHY layer here.
+	if (max_link_rate >= 1000000) {
+		/*
+		 * UHBR rates always use 128b/132b channel encoding, and have
+		 * 97.71% data bandwidth efficiency. Consider max_link_rate the
+		 * link bit rate in units of 10000 bps.
+		 */
+		int max_link_rate_kbps = max_link_rate * 10;
+		max_link_rate_kbps = DIV_ROUND_CLOSEST_ULL(max_link_rate_kbps * 9671, 10000);
+		max_link_rate = max_link_rate_kbps / 8;
+	}
+
+	/*
+	 * Lower than UHBR rates always use 8b/10b channel encoding, and have
+	 * 80% data bandwidth efficiency for SST non-FEC. However, this turns
+	 * out to be a nop by coincidence, and can be skipped:
+	 *
+	 *	int max_link_rate_kbps = max_link_rate * 10;
+	 *	max_link_rate_kbps = DIV_ROUND_CLOSEST_ULL(max_link_rate_kbps * 8, 10);
+	 *	max_link_rate = max_link_rate_kbps / 8;
 	 */
 
-	return max_link_clock * max_lanes;
+	return max_link_rate * max_lanes;
 }
 
 bool intel_dp_can_bigjoiner(struct intel_dp *intel_dp)
drivers/gpu/drm/i915/display/intel_dp.h +1 -1
index 1345d588fc6d..ae0f776bffab 100644
@@ -88,7 +88,7 @@ bool intel_dp_source_supports_hbr3(struct intel_dp *intel_dp);
 
 bool intel_dp_get_colorimetry_status(struct intel_dp *intel_dp);
 int intel_dp_link_required(int pixel_clock, int bpp);
-int intel_dp_max_data_rate(int max_link_clock, int max_lanes);
+int intel_dp_max_data_rate(int max_link_rate, int max_lanes);
 bool intel_dp_can_bigjoiner(struct intel_dp *intel_dp);
 bool intel_dp_needs_vsc_sdp(const struct intel_crtc_state *crtc_state,
 			    const struct drm_connector_state *conn_state);
Signature · 1 line
2.20.1
#16 lore raw

PATCH 12/17 drm/i915/dp: use 128b/132b TPS2 for UHBR+ link rates

In reply to Jani Nikula

128b/132b channel encoding has separate TPS1 and TPS2, although the DPCD register values coincide with 8b/10b TPS1 and TPS2 values. Use 128b/132b TPS2 for channel equalization.

---
 drivers/gpu/drm/i915/display/intel_dp_link_training.c | 10 +++++++---
 1 file changed, 7 insertions(+), 3 deletions(-)
drivers/gpu/drm/i915/display/intel_dp_link_training.c +7 -3
index 053a3c2f7267..031c753fca56 100644
@@ -602,9 +602,9 @@ intel_dp_link_training_clock_recovery(struct intel_dp *intel_dp,
 }
 
 /*
- * Pick training pattern for channel equalization. Training pattern 4 for HBR3
- * or for 1.4 devices that support it, training Pattern 3 for HBR2
- * or 1.2 devices that support it, Training Pattern 2 otherwise.
+ * Pick Training Pattern Sequence (TPS) for channel equalization. 128b/132b TPS2
+ * for UHBR+, TPS4 for HBR3 or for 1.4 devices that support it, TPS3 for HBR2 or
+ * 1.2 devices that support it, TPS2 otherwise.
  */
 static u32 intel_dp_training_pattern(struct intel_dp *intel_dp,
 				     const struct intel_crtc_state *crtc_state,
@@ -612,6 +612,10 @@ static u32 intel_dp_training_pattern(struct intel_dp *intel_dp,
 {
 	bool source_tps3, sink_tps3, source_tps4, sink_tps4;
 
+	/* UHBR+ use separate 128b/132b TPS2 */
+	if (crtc_state->port_clock >= 1000000)
+		return DP_TRAINING_PATTERN_2;
+
 	/*
 	 * Intel platforms that support HBR3 also support TPS4. It is mandatory
 	 * for all downstream devices that support HBR3. There are no known eDP
Signature · 1 line
2.20.1
#17 lore raw

PATCH 13/17 drm/i915/dp: select 128b/132b channel encoding for UHBR rates

In reply to Jani Nikula

UHBR rates and 128b/132b channel encoding go hand in hand.

---
 drivers/gpu/drm/i915/display/intel_dp_link_training.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/gpu/drm/i915/display/intel_dp_link_training.c +2 -1
index 031c753fca56..01f0adc585d0 100644
@@ -495,7 +495,8 @@ intel_dp_prepare_link_train(struct intel_dp *intel_dp,
 				  &rate_select, 1);
 
 	link_config[0] = crtc_state->vrr.enable ? DP_MSA_TIMING_PAR_IGNORE_EN : 0;
-	link_config[1] = DP_SET_ANSI_8B10B;
+	link_config[1] = crtc_state->port_clock > 1000000 ?
+		DP_SET_ANSI_128B132B : DP_SET_ANSI_8B10B;
 	drm_dp_dpcd_write(&intel_dp->aux, DP_DOWNSPREAD_CTRL, link_config, 2);
 
 	intel_dp->DP |= DP_PORT_EN;
Signature · 1 line
2.20.1
#18 lore raw

Re: [Intel-gfx] [PATCH 13/17] drm/i915/dp: select 128b/132b channel encoding for UHBR rates

Quoted 13 lines · Jani Nikula

UHBR rates and 128b/132b channel encoding go hand in hand.

---
 drivers/gpu/drm/i915/display/intel_dp_link_training.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/gpu/drm/i915/display/intel_dp_link_training.c +0 -0
index 031c753fca56..01f0adc585d0 100644

drivers/gpu/drm/i915/display/intel_dp_link_training.c intel_dp_prepare_link_train(struct intel_dp *intel_dp, · line 498

Quoted 5 lines
drivers/gpu/drm/i915/display/intel_dp_link_training.c +1 -1
@@ -495,7 +495,8 @@ intel_dp_prepare_link_train(struct intel_dp *intel_dp,
 				  &rate_select, 1);
 
 	link_config[0] = crtc_state->vrr.enable ? DP_MSA_TIMING_PAR_IGNORE_EN : 0;
-	link_config[1] = DP_SET_ANSI_8B10B;
+	link_config[1] = crtc_state->port_clock > 1000000 ?

Should this be >= ?

Quoted 6 lines
drivers/gpu/drm/i915/display/intel_dp_link_training.c +1 -0
+		DP_SET_ANSI_128B132B : DP_SET_ANSI_8B10B;
 	drm_dp_dpcd_write(&intel_dp->aux, DP_DOWNSPREAD_CTRL, link_config, 2);
 
 	intel_dp->DP |= DP_PORT_EN;
Signature · 1 line
2.20.1
Signature · 2 lines
Ville Syrjälä
Intel
#19 lore raw

Re: [Intel-gfx] [PATCH 13/17] drm/i915/dp: select 128b/132b channel encoding for UHBR rates

Quoted 16 lines · Ville Syrjälä
Quoted 15 lines · Jani Nikula

UHBR rates and 128b/132b channel encoding go hand in hand.

---
 drivers/gpu/drm/i915/display/intel_dp_link_training.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/gpu/drm/i915/display/intel_dp_link_training.c +0 -0
index 031c753fca56..01f0adc585d0 100644
@@ -495,7 +495,8 @@ intel_dp_prepare_link_train(struct intel_dp *intel_dp,
 				  &rate_select, 1);
 
Quoted 5 lines

drivers/gpu/drm/i915/display/intel_dp_link_training.c intel_dp_prepare_link_train(struct intel_dp *intel_dp, · line 498

Quoted 3 lines
drivers/gpu/drm/i915/display/intel_dp_link_training.c +1 -1
 	link_config[0] = crtc_state->vrr.enable ? DP_MSA_TIMING_PAR_IGNORE_EN : 0;
-	link_config[1] = DP_SET_ANSI_8B10B;
+	link_config[1] = crtc_state->port_clock > 1000000 ?

Should this be >= ?

Yes, whoops, thanks!

Quoted 7 lines
Quoted 7 lines
drivers/gpu/drm/i915/display/intel_dp_link_training.c +1 -0
+		DP_SET_ANSI_128B132B : DP_SET_ANSI_8B10B;
 	drm_dp_dpcd_write(&intel_dp->aux, DP_DOWNSPREAD_CTRL, link_config, 2);
 
 	intel_dp->DP |= DP_PORT_EN;
Signature · 1 line
2.20.1
Signature · 1 line
Jani Nikula, Intel Open Source Graphics Center
#20 lore raw

PATCH 14/17 drm/i915/dg2: configure TRANS_DP2_CTL for DP 2.0

In reply to Jani Nikula

Set the DP 2.0 128b/132b channel encoding for UHBR rates.

Bspec: 54128

---
 drivers/gpu/drm/i915/display/intel_ddi.c | 17 ++++++++++++++++-
 1 file changed, 16 insertions(+), 1 deletion(-)
drivers/gpu/drm/i915/display/intel_ddi.c +16 -1
index 203a54f905f6..8b8f5d679b72 100644
@@ -407,6 +407,20 @@ static u32 bdw_trans_port_sync_master_select(enum transcoder master_transcoder)
 		return master_transcoder + 1;
 }
 
+static void
+intel_ddi_config_transcoder_dp2(struct intel_encoder *encoder,
+				const struct intel_crtc_state *crtc_state)
+{
+	struct drm_i915_private *i915 = to_i915(encoder->base.dev);
+	enum transcoder cpu_transcoder = crtc_state->cpu_transcoder;
+	u32 val = 0;
+
+	if (crtc_state->port_clock > 1000000)
+		val = TRANS_DP2_128B132B_CHANNEL_CODING;
+
+	intel_de_write(i915, TRANS_DP2_CTL(cpu_transcoder), val);
+}
+
 /*
  * Returns the TRANS_DDI_FUNC_CTL value based on CRTC state.
  *
@@ -2375,7 +2389,8 @@ static void dg2_ddi_pre_enable_dp(struct intel_atomic_state *state,
 	 */
 	intel_ddi_enable_pipe_clock(encoder, crtc_state);
 
-	/* 5.b Not relevant to i915 for now */
+	/* 5.b Configure transcoder for DP 2.0 128b/132b */
+	intel_ddi_config_transcoder_dp2(encoder, crtc_state);
 
 	/*
 	 * 5.c Configure TRANS_DDI_FUNC_CTL DDI Select, DDI Mode Select & MST
Signature · 1 line
2.20.1
#21 lore raw

PATCH 15/17 drm/i915/dg2: use 128b/132b transcoder DDI mode

In reply to Jani Nikula

128b/132b has a separate transcoder DDI mode, which also requires the MST transport select to be set. Note that we'll use DP MST also for single-stream 128b/132b.

Having the FDI and 128b/132b modes share the register mode value complicates things a bit.

Bspec: 50493

---
 drivers/gpu/drm/i915/display/intel_ddi.c | 27 ++++++++++++++++++------
 1 file changed, 20 insertions(+), 7 deletions(-)
drivers/gpu/drm/i915/display/intel_ddi.c +20 -7
index 8b8f5d679b72..1ee817348bf5 100644
@@ -505,7 +505,10 @@ intel_ddi_transcoder_func_reg_val_get(struct intel_encoder *encoder,
 		temp |= TRANS_DDI_MODE_SELECT_FDI_OR_128B132B;
 		temp |= (crtc_state->fdi_lanes - 1) << 1;
 	} else if (intel_crtc_has_type(crtc_state, INTEL_OUTPUT_DP_MST)) {
-		temp |= TRANS_DDI_MODE_SELECT_DP_MST;
+		if (crtc_state->port_clock > 1000000)
+			temp |= TRANS_DDI_MODE_SELECT_FDI_OR_128B132B;
+		else
+			temp |= TRANS_DDI_MODE_SELECT_DP_MST;
 		temp |= DDI_PORT_WIDTH(crtc_state->lane_count);
 
 		if (DISPLAY_VER(dev_priv) >= 12) {
@@ -693,7 +696,12 @@ bool intel_ddi_connector_get_hw_state(struct intel_connector *intel_connector)
 		break;
 
 	case TRANS_DDI_MODE_SELECT_FDI_OR_128B132B:
-		ret = type == DRM_MODE_CONNECTOR_VGA;
+		if (IS_DG2(dev_priv))
+			/* 128b/132b */
+			ret = false;
+		else
+			/* FDI */
+			ret = type == DRM_MODE_CONNECTOR_VGA;
 		break;
 
 	default:
@@ -780,8 +788,9 @@ static void intel_ddi_get_encoder_pipes(struct intel_encoder *encoder,
 		if ((tmp & port_mask) != ddi_select)
 			continue;
 
-		if ((tmp & TRANS_DDI_MODE_SELECT_MASK) ==
-		    TRANS_DDI_MODE_SELECT_DP_MST)
+		if ((tmp & TRANS_DDI_MODE_SELECT_MASK) == TRANS_DDI_MODE_SELECT_DP_MST ||
+		    (IS_DG2(dev_priv) &&
+		     (tmp & TRANS_DDI_MODE_SELECT_MASK) == TRANS_DDI_MODE_SELECT_FDI_OR_128B132B))
 			mst_pipe_mask |= BIT(p);
 
 		*pipe_mask |= BIT(p);
@@ -3572,9 +3581,6 @@ static void intel_ddi_read_func_ctl(struct intel_encoder *encoder,
 		pipe_config->output_types |= BIT(INTEL_OUTPUT_HDMI);
 		pipe_config->lane_count = 4;
 		break;
-	case TRANS_DDI_MODE_SELECT_FDI_OR_128B132B:
-		pipe_config->output_types |= BIT(INTEL_OUTPUT_ANALOG);
-		break;
 	case TRANS_DDI_MODE_SELECT_DP_SST:
 		if (encoder->type == INTEL_OUTPUT_EDP)
 			pipe_config->output_types |= BIT(INTEL_OUTPUT_EDP);
@@ -3603,6 +3609,13 @@ static void intel_ddi_read_func_ctl(struct intel_encoder *encoder,
 			pipe_config->infoframes.enable |=
 				intel_hdmi_infoframes_enabled(encoder, pipe_config);
 		break;
+	case TRANS_DDI_MODE_SELECT_FDI_OR_128B132B:
+		if (!IS_DG2(dev_priv)) {
+			/* FDI */
+			pipe_config->output_types |= BIT(INTEL_OUTPUT_ANALOG);
+			break;
+		}
+		fallthrough; /* 128b/132b */
 	case TRANS_DDI_MODE_SELECT_DP_MST:
 		pipe_config->output_types |= BIT(INTEL_OUTPUT_DP_MST);
 		pipe_config->lane_count =
Signature · 1 line
2.20.1
#22 lore raw

Re: [Intel-gfx] [PATCH 15/17] drm/i915/dg2: use 128b/132b transcoder DDI mode

Quoted 30 lines · Jani Nikula

128b/132b has a separate transcoder DDI mode, which also requires the MST transport select to be set. Note that we'll use DP MST also for single-stream 128b/132b.

Having the FDI and 128b/132b modes share the register mode value complicates things a bit.

Bspec: 50493

---
 drivers/gpu/drm/i915/display/intel_ddi.c | 27 ++++++++++++++++++------
 1 file changed, 20 insertions(+), 7 deletions(-)
drivers/gpu/drm/i915/display/intel_ddi.c +4 -1
index 8b8f5d679b72..1ee817348bf5 100644
@@ -505,7 +505,10 @@ intel_ddi_transcoder_func_reg_val_get(struct intel_encoder *encoder,
 		temp |= TRANS_DDI_MODE_SELECT_FDI_OR_128B132B;
 		temp |= (crtc_state->fdi_lanes - 1) << 1;
 	} else if (intel_crtc_has_type(crtc_state, INTEL_OUTPUT_DP_MST)) {
-		temp |= TRANS_DDI_MODE_SELECT_DP_MST;
+		if (crtc_state->port_clock > 1000000)
+			temp |= TRANS_DDI_MODE_SELECT_FDI_OR_128B132B;
+		else
+			temp |= TRANS_DDI_MODE_SELECT_DP_MST;
 		temp |= DDI_PORT_WIDTH(crtc_state->lane_count);
 
 		if (DISPLAY_VER(dev_priv) >= 12) {

drivers/gpu/drm/i915/display/intel_ddi.c bool intel_ddi_connector_get_hw_state(struct intel_connector *intel_connector) · line 701

Quoted 7 lines
drivers/gpu/drm/i915/display/intel_ddi.c +3 -1
@@ -693,7 +696,12 @@ bool intel_ddi_connector_get_hw_state(struct intel_connector *intel_connector)
 		break;
 
 	case TRANS_DDI_MODE_SELECT_FDI_OR_128B132B:
-		ret = type == DRM_MODE_CONNECTOR_VGA;
+		if (IS_DG2(dev_priv))
+			/* 128b/132b */
+			ret = false;

Maybe introduce HAS_FDI() or something to avoid these platform checks all over?

Quoted 44 lines
drivers/gpu/drm/i915/display/intel_ddi.c +13 -5
+		else
+			/* FDI */
+			ret = type == DRM_MODE_CONNECTOR_VGA;
 		break;
 
 	default:
@@ -780,8 +788,9 @@ static void intel_ddi_get_encoder_pipes(struct intel_encoder *encoder,
 		if ((tmp & port_mask) != ddi_select)
 			continue;
 
-		if ((tmp & TRANS_DDI_MODE_SELECT_MASK) ==
-		    TRANS_DDI_MODE_SELECT_DP_MST)
+		if ((tmp & TRANS_DDI_MODE_SELECT_MASK) == TRANS_DDI_MODE_SELECT_DP_MST ||
+		    (IS_DG2(dev_priv) &&
+		     (tmp & TRANS_DDI_MODE_SELECT_MASK) == TRANS_DDI_MODE_SELECT_FDI_OR_128B132B))
 			mst_pipe_mask |= BIT(p);
 
 		*pipe_mask |= BIT(p);
@@ -3572,9 +3581,6 @@ static void intel_ddi_read_func_ctl(struct intel_encoder *encoder,
 		pipe_config->output_types |= BIT(INTEL_OUTPUT_HDMI);
 		pipe_config->lane_count = 4;
 		break;
-	case TRANS_DDI_MODE_SELECT_FDI_OR_128B132B:
-		pipe_config->output_types |= BIT(INTEL_OUTPUT_ANALOG);
-		break;
 	case TRANS_DDI_MODE_SELECT_DP_SST:
 		if (encoder->type == INTEL_OUTPUT_EDP)
 			pipe_config->output_types |= BIT(INTEL_OUTPUT_EDP);
@@ -3603,6 +3609,13 @@ static void intel_ddi_read_func_ctl(struct intel_encoder *encoder,
 			pipe_config->infoframes.enable |=
 				intel_hdmi_infoframes_enabled(encoder, pipe_config);
 		break;
+	case TRANS_DDI_MODE_SELECT_FDI_OR_128B132B:
+		if (!IS_DG2(dev_priv)) {
+			/* FDI */
+			pipe_config->output_types |= BIT(INTEL_OUTPUT_ANALOG);
+			break;
+		}
+		fallthrough; /* 128b/132b */
 	case TRANS_DDI_MODE_SELECT_DP_MST:
 		pipe_config->output_types |= BIT(INTEL_OUTPUT_DP_MST);
 		pipe_config->lane_count =
Signature · 1 line
2.20.1
Signature · 2 lines
Ville Syrjälä
Intel
#23 lore raw

PATCH 16/17 drm/i915/dg2: configure TRANS_DP2_VFREQ{HIGH, LOW} for 128b/132b

In reply to Jani Nikula

There's a new register pair for 128b/132b mode where you need to set the pixel clock in Hz.

Bspec: 54128

---
 drivers/gpu/drm/i915/display/intel_dp_mst.c | 11 +++++++++++
 1 file changed, 11 insertions(+)
drivers/gpu/drm/i915/display/intel_dp_mst.c +11 -0
index d104441344c0..a003cc98312b 100644
@@ -550,6 +550,17 @@ static void intel_mst_enable_dp(struct intel_atomic_state *state,
 
 	clear_act_sent(encoder, pipe_config);
 
+	if (pipe_config->port_clock > 1000000) {
+		const struct drm_display_mode *adjusted_mode =
+			&pipe_config->hw.adjusted_mode;
+		u64 crtc_clock_hz = KHz(adjusted_mode->crtc_clock);
+
+		intel_de_write(dev_priv, TRANS_DP2_VFREQHIGH(pipe_config->cpu_transcoder),
+			       TRANS_DP2_VFREQ_PIXEL_CLOCK(crtc_clock_hz >> 24));
+		intel_de_write(dev_priv, TRANS_DP2_VFREQLOW(pipe_config->cpu_transcoder),
+			       TRANS_DP2_VFREQ_PIXEL_CLOCK(crtc_clock_hz & 0xffffff));
+	}
+
 	intel_ddi_enable_transcoder_func(encoder, pipe_config);
 
 	intel_de_rmw(dev_priv, TRANS_DDI_FUNC_CTL(trans), 0,
Signature · 1 line
2.20.1
#24 lore raw

PATCH 17/17 drm/i915/dg2: update link training for 128b/132b

In reply to Jani Nikula

The 128b/132b channel coding link training uses more straightforward TX FFE preset values.

---
 drivers/gpu/drm/i915/display/intel_ddi.c      | 13 ++-
 .../drm/i915/display/intel_dp_link_training.c | 86 +++++++++++++------
 2 files changed, 70 insertions(+), 29 deletions(-)
drivers/gpu/drm/i915/display/intel_ddi.c +9 -4
index 1ee817348bf5..e32d2e39f4d5 100644
@@ -1397,11 +1397,16 @@ static int translate_signal_level(struct intel_dp *intel_dp,
 static int intel_ddi_dp_level(struct intel_dp *intel_dp,
 			      const struct intel_crtc_state *crtc_state)
 {
-	u8 train_set = intel_dp->train_set[0];
-	u8 signal_levels = train_set & (DP_TRAIN_VOLTAGE_SWING_MASK |
-					DP_TRAIN_PRE_EMPHASIS_MASK);
+	if (crtc_state->port_clock >= 1000000) {
+		/* FIXME: We'll want independent presets for each lane. */
+		return intel_dp->train_set[0] & DP_TX_FFE_PRESET_VALUE_MASK;
+	} else {
+		u8 train_set = intel_dp->train_set[0];
+		u8 signal_levels = train_set & (DP_TRAIN_VOLTAGE_SWING_MASK |
+						DP_TRAIN_PRE_EMPHASIS_MASK);
 
-	return translate_signal_level(intel_dp, signal_levels);
+		return translate_signal_level(intel_dp, signal_levels);
+	}
 }
 
 static void
drivers/gpu/drm/i915/display/intel_dp_link_training.c +61 -25

119 lines not on this page · raw message

Signature · 1 line
2.20.1
#25 lore raw

[Intel-gfx] ✗ Fi.CI.CHECKPATCH: warning for drm/i915/dp: dp 2.0 enabling prep work

In reply to Jani Nikula
== Series Details ==

== Series Details ==

Series: drm/i915/dp: dp 2.0 enabling prep work
URL : https://patchwork.freedesktop.org/series/93800/
State : warning

== Summary ==

$ dim checkpatch origin/drm-tip
098494421cf3 drm/dp: add DP 2.0 UHBR link rate and bw code conversions
15972d4824f6 drm/dp: use more of the extended receiver cap
176cd12c2a2e drm/dp: add LTTPR DP 2.0 DPCD addresses
348fff506827 drm/dp: add helper for extracting adjust 128b/132b TX FFE preset
2c801bbdc46b drm/i915/dp: use actual link rate values in struct link_config_limits
-:26: CHECK:MULTIPLE_ASSIGNMENTS: multiple assignments should be avoided
#26: FILE: drivers/gpu/drm/i915/display/intel_dp.c:1047:
+				limits->min_rate = limits->max_rate =

total: 0 errors, 0 warnings, 1 checks, 106 lines checked 4d03932add3c drm/i915/dp: read sink UHBR rates bd393efa3f8d drm/i915/dg2: add TRANS_DP2_CTL register definition -:24: WARNING:LONG_LINE: line length of 102 exceeds 100 columns #24: FILE: drivers/gpu/drm/i915/i915_reg.h:9106:
+#define TRANS_DP2_CTL(trans) _MMIO_TRANS(trans, _TRANS_DP2_CTL_A, _TRANS_DP2_CTL_B)

total: 0 errors, 1 warnings, 0 checks, 15 lines checked 2ae1f5cd9112 drm/i915/dg2: add DG2+ TRANS_DDI_FUNC_CTL DP 2.0 128b/132b mode 09dd0b1c53f5 drm/i915/dg2: add TRANS_DP2_VFREQHIGH and TRANS_DP2_VFREQLOW -:25: WARNING:LONG_LINE: line length of 114 exceeds 100 columns #25: FILE: drivers/gpu/drm/i915/i915_reg.h:9115:
+#define TRANS_DP2_VFREQHIGH(trans) _MMIO_TRANS(trans, _TRANS_DP2_VFREQHIGH_A, _TRANS_DP2_VFREQHIGH_B)

-:27: WARNING:LONG_LINE: line length of 106 exceeds 100 columns #27: FILE: drivers/gpu/drm/i915/i915_reg.h:9117:
+#define TRANS_DP2_VFREQ_PIXEL_CLOCK(clk_hz) REG_FIELD_PREP(TRANS_DP2_VFREQ_PIXEL_CLOCK_MASK, (clk_hz))

-:33: WARNING:LONG_LINE: line length of 112 exceeds 100 columns #33: FILE: drivers/gpu/drm/i915/i915_reg.h:9123:
+#define TRANS_DP2_VFREQLOW(trans) _MMIO_TRANS(trans, _TRANS_DP2_VFREQLOW_A, _TRANS_DP2_VFREQLOW_B)

total: 0 errors, 3 warnings, 0 checks, 20 lines checked 310bd160b5df drm/i915/dg2: add DG2 UHBR source rates 9cf6be09b318 drm/i915/dp: add max data rate calculation for UHBR rates -:70: WARNING:LINE_SPACING: Missing a blank line after declarations #70: FILE: drivers/gpu/drm/i915/display/intel_dp.c:254:
+ int max_link_rate_kbps = max_link_rate * 10;
+ max_link_rate_kbps = DIV_ROUND_CLOSEST_ULL(max_link_rate_kbps * 9671, 10000);

total: 0 errors, 1 warnings, 0 checks, 75 lines checked
7d3f86063b7b drm/i915/dp: use 128b/132b TPS2 for UHBR+ link rates 76465b4d3708 drm/i915/dp: select 128b/132b channel encoding for UHBR rates 753442fe1e74 drm/i915/dg2: configure TRANS_DP2_CTL for DP 2.0 73b7a835f7b3 drm/i915/dg2: use 128b/132b transcoder DDI mode 44526b8ce97b drm/i915/dg2: configure TRANS_DP2_VFREQ{HIGH, LOW} for 128b/132b f619e6bfa217 drm/i915/dg2: update link training for 128b/132b
-:25: WARNING:UNNECESSARY_ELSE: else is not generally useful after a break or return #25: FILE: drivers/gpu/drm/i915/display/intel_ddi.c:1403:
+ return intel_dp->train_set[0] & DP_TX_FFE_PRESET_VALUE_MASK;
+ } else {

-:44: ERROR:POINTER_LOCATION: "foo* bar" should be "foo *bar" #44: FILE: drivers/gpu/drm/i915/display/intel_dp_link_training.c:304:
+static void intel_dp_128b132b_adjust_train(struct intel_dp* intel_dp,

total: 1 errors, 1 warnings, 0 checks, 139 lines checked

#26 lore raw

[Intel-gfx] ✗ Fi.CI.SPARSE: warning for drm/i915/dp: dp 2.0 enabling prep work

In reply to Jani Nikula
== Series Details ==

== Series Details ==

Series: drm/i915/dp: dp 2.0 enabling prep work
URL : https://patchwork.freedesktop.org/series/93800/
State : warning

== Summary ==

$ dim sparse --fast origin/drm-tip
Sparse version: v0.6.2
Fast mode used, each commit won't be checked separately.
-
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgv_sriovmsg.h:316:49: error: static assertion failed: "amd_sriov_msg_pf2vf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgpu_debugfs.c:1345:25: error: incompatible types in comparison expression (different address spaces):
+drivers/gpu/drm/amd/amdgpu/amdgpu_debugfs.c:1345:25:    struct dma_fence *
+drivers/gpu/drm/amd/amdgpu/amdgpu_debugfs.c:1345:25:    struct dma_fence [noderef] __rcu *
+drivers/gpu/drm/amd/amdgpu/amdgpu_debugfs.c:1346:17: error: incompatible types in comparison expression (different address spaces):
+drivers/gpu/drm/amd/amdgpu/amdgpu_debugfs.c:1346:17:    struct dma_fence *
+drivers/gpu/drm/amd/amdgpu/amdgpu_debugfs.c:1346:17:    struct dma_fence [noderef] __rcu *
+drivers/gpu/drm/amd/amdgpu/amdgpu_debugfs.c:1405:17: error: incompatible types in comparison expression (different address spaces):
+drivers/gpu/drm/amd/amdgpu/amdgpu_debugfs.c:1405:17:    struct dma_fence *
+drivers/gpu/drm/amd/amdgpu/amdgpu_debugfs.c:1405:17:    struct dma_fence [noderef] __rcu *
+drivers/gpu/drm/amd/amdgpu/amdgpu_device.c:354:16: error: incompatible types in comparison expression (different type sizes):
+drivers/gpu/drm/amd/amdgpu/amdgpu_device.c:354:16:    unsigned long *
+drivers/gpu/drm/amd/amdgpu/amdgpu_device.c:354:16:    unsigned long long *
+drivers/gpu/drm/amd/amdgpu/amdgpu_fence.c:275:25: error: incompatible types in comparison expression (different address spaces):
+drivers/gpu/drm/amd/amdgpu/amdgpu_fence.c:275:25:    struct dma_fence *
+drivers/gpu/drm/amd/amdgpu/amdgpu_fence.c:275:25:    struct dma_fence [noderef] __rcu *
+drivers/gpu/drm/amd/amdgpu/amdgpu_fence.c:276:17: error: incompatible types in comparison expression (different address spaces):
+drivers/gpu/drm/amd/amdgpu/amdgpu_fence.c:276:17:    struct dma_fence *
+drivers/gpu/drm/amd/amdgpu/amdgpu_fence.c:276:17:    struct dma_fence [noderef] __rcu *
+drivers/gpu/drm/amd/amdgpu/amdgpu_fence.c:330:17: error: incompatible types in comparison expression (different address spaces):
+drivers/gpu/drm/amd/amdgpu/amdgpu_fence.c:330:17:    struct dma_fence *
+drivers/gpu/drm/amd/amdgpu/amdgpu_fence.c:330:17:    struct dma_fence [noderef] __rcu *
+drivers/gpu/drm/amd/amdgpu/amdgpu_ras_eeprom.h:123:51: error: marked inline, but without a definition
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv_sriovmsg.h:312:49: error: static assertion failed: "amd_sriov_msg_vf2pf_info must be 1 KB"
+drivers/gpu/drm/amd/amdgpu/amdgv
#27 lore raw

[Intel-gfx] ✓ Fi.CI.BAT: success for drm/i915/dp: dp 2.0 enabling prep work

In reply to Jani Nikula
== Series Details ==

== Series Details ==

Series: drm/i915/dp: dp 2.0 enabling prep work
URL : https://patchwork.freedesktop.org/series/93800/
State : success

== Summary ==

CI Bug Log - changes from CI_DRM_10497 -> Patchwork_20850
====================================================

Summary
-------

**SUCCESS**

No regressions found.

External URL: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_20850/index.html

Known issues
------------

Here are the changes found in Patchwork_20850 that come from known issues:

### IGT changes ###

#### Issues hit ####

* igt@amdgpu/amd_basic@cs-gfx:
- fi-rkl-guc: NOTRUN -> [SKIP][1] ([fdo#109315]) +17 similar issues
[1]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_20850/fi-rkl-guc/igt@amdgpu/[email protected]
- fi-kbl-soraka: NOTRUN -> [SKIP][2] ([fdo#109271]) +6 similar issues
[2]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_20850/fi-kbl-soraka/igt@amdgpu/[email protected]

* igt@runner@aborted:
- fi-bdw-5557u: NOTRUN -> [FAIL][3] ([i915#1602] / [i915#2029])
[3]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_20850/fi-bdw-5557u/igt@[email protected]

#### Possible fixes ####

* igt@core_hotunplug@unbind-rebind:
- fi-rkl-guc: [DMESG-WARN][4] ([i915#3925]) -> [PASS][5]
[4]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_10497/fi-rkl-guc/igt@[email protected]
[5]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_20850/fi-rkl-guc/igt@[email protected]

#### Warnings ####

* igt@i915_pm_rpm@basic-rte:
- fi-kbl-guc: [FAIL][6] ([i915#579]) -> [SKIP][7] ([fdo#109271])
[6]: https://intel-gfx-ci.01.org/tree/drm-tip/CI_DRM_10497/fi-kbl-guc/igt@[email protected]
[7]: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_20850/fi-kbl-guc/igt@[email protected]

[fdo#109271]: https://bugs.freedesktop.org/show_bug.cgi?id=109271
[fdo#109315]: https://bugs.freedesktop.org/show_bug.cgi?id=109315
[i915#1602]: https://gitlab.freedesktop.org/drm/intel/issues/1602
[i915#2029]: https://gitlab.freedesktop.org/drm/intel/issues/2029
[i915#3925]: https://gitlab.freedesktop.org/drm/intel/issues/3925
[i915#579]: https://gitlab.freedesktop.org/drm/intel/issues/579

Participating hosts (34 -> 33)
------------------------------

Missing (1): fi-bsw-cyan

Build changes
-------------

* Linux: CI_DRM_10497 -> Patchwork_20850

CI-20190529: 20190529
CI_DRM_10497: c50a8ea72915f1e3972d011690a423bafbee7a58 @ git://anongit.freedesktop.org/gfx-ci/linux
IGT_6178: 146260200f9a6d4536e48a195e2ab49a07d4f0c1 @ https://gitlab.freedesktop.org/drm/igt-gpu-tools.git
Patchwork_20850: f619e6bfa217e2f33dfb31e0da1262cae8c9209f @ git://anongit.freedesktop.org/gfx-ci/linux

== Linux commits ==

f619e6bfa217 drm/i915/dg2: update link training for 128b/132b 44526b8ce97b drm/i915/dg2: configure TRANS_DP2_VFREQ{HIGH, LOW} for 128b/132b 73b7a835f7b3 drm/i915/dg2: use 128b/132b transcoder DDI mode 753442fe1e74 drm/i915/dg2: configure TRANS_DP2_CTL for DP 2.0 76465b4d3708 drm/i915/dp: select 128b/132b channel encoding for UHBR rates 7d3f86063b7b drm/i915/dp: use 128b/132b TPS2 for UHBR+ link rates 9cf6be09b318 drm/i915/dp: add max data rate calculation for UHBR rates 310bd160b5df drm/i915/dg2: add DG2 UHBR source rates
09dd0b1c53f5 drm/i915/dg2: add TRANS_DP2_VFREQHIGH and TRANS_DP2_VFREQLOW 2ae1f5cd9112 drm/i915/dg2: add DG2+ TRANS_DDI_FUNC_CTL DP 2.0 128b/132b mode bd393efa3f8d drm/i915/dg2: add TRANS_DP2_CTL register definition 4d03932add3c drm/i915/dp: read sink UHBR rates
2c801bbdc46b drm/i915/dp: use actual link rate values in struct link_config_limits 348fff506827 drm/dp: add helper for extracting adjust 128b/132b TX FFE preset 176cd12c2a2e drm/dp: add LTTPR DP 2.0 DPCD addresses
15972d4824f6 drm/dp: use more of the extended receiver cap 098494421cf3 drm/dp: add DP 2.0 UHBR link rate and bw code conversions

== Logs ==

For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_20850/index.html