Add support for MT8365 EVK board
Subsystems (19)
cover Add support for MT8365 EVK board
This patch series adds support for the MT8365 EVK board.
This series has dependencies on the following series:
https://patchwork.kernel.org/project/linux-mediatek/list/?series=646256
https://patchwork.kernel.org/project/linux-mediatek/list/?series=646091
https://patchwork.kernel.org/project/linux-mediatek/list/?series=646083
https://patchwork.kernel.org/project/linux-mediatek/list/?series=646081
https://patchwork.kernel.org/project/linux-mediatek/list/?series=646076
https://patchwork.kernel.org/project/linux-mediatek/list/?series=646068
https://patchwork.kernel.org/project/linux-mediatek/list/?series=646020
https://patchwork.kernel.org/project/linux-mediatek/list/?series=646052
https://lore.kernel.org/r/[email protected]
https://lore.kernel.org/r/[email protected]
https://lore.kernel.org/r/[email protected]
https://lore.kernel.org/r/[email protected]
https://lore.kernel.org/all/[email protected]/
Fabien Parent (17):
dt-bindings: i2c: i2c-mt65xx: add binding for MT8365 SoC
dt-bindings: memory: add mt8365 SoC binding documentation
dt-bindings: mmc: mtk-sd: add bindings for MT8365 SoC
dt-bindings: arm: mediatek: Add binding for mt8365-evk board
dt-bindings: dma: mediatek,uart-dma: add MT8365 bindings
dt-bindings: iio: adc: mediatek: add MT8365 SoC bindings
dt-bindings: nvmem: mediatek,efuse: add MT8365 bindings
dt-bindings: watchdog: mtk-wdt: Add MT8365 SoC bindings
dt-bindings: spi: mt65xx: add MT8365 SoC bindings
dt-bindings: serial: mediatek: add MT8365 bindings
dt-bindings: phy: mediatek,dsi-phy: Add MT8365 SoC bindings
dt-bindings: phy: mediatek,tphy: add MT8365 SoC bindings
dt-bindings: usb: mediatek,mtu3: add MT8365 SoC bindings
dt-bindings: usb: mediatek,mtk-xhci: add MT8365 SoC bindings
arm64: dts: mediatek: add mt6357 device-tree
arm64: dts: mediatek: add mt8365 device-tree
arm64: dts: mediatek: add mt8365-evk board device-tree
.../devicetree/bindings/arm/mediatek.yaml | 4 + .../bindings/dma/mediatek,uart-dma.yaml | 1 + .../devicetree/bindings/i2c/i2c-mt65xx.yaml | 4 + .../iio/adc/mediatek,mt2701-auxadc.yaml | 1 + .../mediatek,smi-common.yaml | 6 + .../memory-controllers/mediatek,smi-larb.yaml | 6 + .../devicetree/bindings/mmc/mtk-sd.yaml | 3 + .../bindings/nvmem/mediatek,efuse.yaml | 1 + .../bindings/phy/mediatek,dsi-phy.yaml | 4 + .../bindings/phy/mediatek,tphy.yaml | 1 + .../bindings/serial/mediatek,uart.yaml | 1 + .../bindings/spi/mediatek,spi-mt65xx.yaml | 1 + .../bindings/usb/mediatek,mtk-xhci.yaml | 1 + .../bindings/usb/mediatek,mtu3.yaml | 1 + .../devicetree/bindings/watchdog/mtk-wdt.txt | 1 + arch/arm64/boot/dts/mediatek/Makefile | 1 + arch/arm64/boot/dts/mediatek/mt6357.dtsi | 272 +++++ arch/arm64/boot/dts/mediatek/mt8365-evk.dts | 578 +++++++++ arch/arm64/boot/dts/mediatek/mt8365.dtsi | 1047 +++++++++++++++++ 19 files changed, 1934 insertions(+) create mode 100644 arch/arm64/boot/dts/mediatek/mt6357.dtsi create mode 100644 arch/arm64/boot/dts/mediatek/mt8365-evk.dts create mode 100644 arch/arm64/boot/dts/mediatek/mt8365.dtsi
Signature · 1 line
2.36.1
PATCH 1/17 dt-bindings: i2c: i2c-mt65xx: add binding for MT8365 SoC
Add binding documentation for the MT8365 I2C controllers.
--- Documentation/devicetree/bindings/i2c/i2c-mt65xx.yaml | 4 ++++ 1 file changed, 4 insertions(+)
Documentation/devicetree/bindings/i2c/i2c-mt65xx.yaml +4 -0
@@ -43,6 +43,10 @@ properties: - enum: - mediatek,mt8195-i2c - const: mediatek,mt8192-i2c + - items: + - enum: + - mediatek,mt8365-i2c + - const: mediatek,mt8168-i2c reg: items:
Signature · 1 line
2.36.1
Re: [PATCH 01/17] dt-bindings: i2c: i2c-mt65xx: add binding for MT8365 SoC
Quoted 13 lines · Fabien Parent
Add binding documentation for the MT8365 I2C controllers.
Signed-off-by Fabien Parent <[email protected]>Acked-by Rob Herring <[email protected]>--- Documentation/devicetree/bindings/i2c/i2c-mt65xx.yaml | 4 ++++ 1 file changed, 4 insertions(+)Documentation/devicetree/bindings/i2c/i2c-mt65xx.yaml +0
-0
Documentation/devicetree/bindings/i2c/i2c-mt65xx.yaml properties: · line 49
Quoted 7 lines
Documentation/devicetree/bindings/i2c/i2c-mt65xx.yaml +4
-0@@ -43,6 +43,10 @@ properties: - enum: - mediatek,mt8195-i2c - const: mediatek,mt8192-i2c + - items: + - enum: + - mediatek,mt8365-i2c + - const: mediatek,mt8168-i2c
Order entries by last item, so this goes before mt8192
Documentation/devicetree/bindings/i2c/i2c-mt65xx.yaml properties: · line 51
Quoted 3 lines
Documentation/devicetree/bindings/i2c/i2c-mt65xx.yaml +0
-0reg: items:
Best regards,
Krzysztof
Signature · 3 lines
linux-phy mailing list [email protected] https://lists.infradead.org/mailman/listinfo/linux-phy
PATCH 2/17 dt-bindings: memory: add mt8365 SoC binding documentation
In reply to Fabien ParentAdd MediaTek SMI bindings for MT8365 SoC.
--- .../bindings/memory-controllers/mediatek,smi-common.yaml | 6 ++++++ .../bindings/memory-controllers/mediatek,smi-larb.yaml | 6 ++++++ 2 files changed, 12 insertions(+)
Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.yaml +6 -0
@@ -46,6 +46,11 @@ properties: - const: mediatek,mt7623-smi-common - const: mediatek,mt2701-smi-common + - description: for mt8365 + items: + - const: mediatek,mt8365-smi-common + - const: mediatek,mt8186-smi-common + reg: maxItems: 1
@@ -130,6 +135,7 @@ allOf: - mediatek,mt8192-smi-common - mediatek,mt8195-smi-common-vdo - mediatek,mt8195-smi-common-vpp + - mediatek,mt8365-smi-common then: properties:
Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.yaml +6 -0
@@ -32,6 +32,11 @@ properties: - const: mediatek,mt7623-smi-larb - const: mediatek,mt2701-smi-larb + - description: for mt8365 + items: + - const: mediatek,mt8365-smi-larb + - const: mediatek,mt8186-smi-larb + reg: maxItems: 1
@@ -78,6 +83,7 @@ allOf: - mediatek,mt8183-smi-larb - mediatek,mt8186-smi-larb - mediatek,mt8195-smi-larb + - mediatek,mt8365-smi-larb then: properties:
Signature · 1 line
2.36.1
Re: [PATCH 02/17] dt-bindings: memory: add mt8365 SoC binding documentation
Quoted 13 lines · Fabien Parent
Add MediaTek SMI bindings for MT8365 SoC.
Signed-off-by Fabien Parent <[email protected]>--- .../bindings/memory-controllers/mediatek,smi-common.yaml | 6 ++++++ .../bindings/memory-controllers/mediatek,smi-larb.yaml | 6 ++++++ 2 files changed, 12 insertions(+)Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.yaml +0
-0
Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.yaml properties: · line 49
Quoted 4 lines
Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.yaml +1
-0@@ -46,6 +46,11 @@ properties: - const: mediatek,mt7623-smi-common - const: mediatek,mt2701-smi-common + - description: for mt8365
Skip description and:
Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.yaml properties: · line 51
Quoted 2 lines
Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.yaml +2
-0+ items: + - const: mediatek,mt8365-smi-common
This should be rather enum. I see existing code did that way, but this way makes it bloated. If new device compatible with mt8186 comes, should be added to this enum, not to new items.
Quoted 18 lines
Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.yaml +3
-0+ - const: mediatek,mt8186-smi-common + reg: maxItems: 1@@ -130,6 +135,7 @@ allOf: - mediatek,mt8192-smi-common - mediatek,mt8195-smi-common-vdo - mediatek,mt8195-smi-common-vpp + - mediatek,mt8365-smi-common then: properties:Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.yaml +0
-0
Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.yaml properties: · line 38
Quoted 7 lines
Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.yaml +4
-0@@ -32,6 +32,11 @@ properties: - const: mediatek,mt7623-smi-larb - const: mediatek,mt2701-smi-larb + - description: for mt8365 + items: + - const: mediatek,mt8365-smi-larb + - const: mediatek,mt8186-smi-larb
Ditto.
Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.yaml allOf: · line 89
Quoted 12 lines
Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.yaml +2
-0+ reg: maxItems: 1@@ -78,6 +83,7 @@ allOf: - mediatek,mt8183-smi-larb - mediatek,mt8186-smi-larb - mediatek,mt8195-smi-larb + - mediatek,mt8365-smi-larb then: properties:
Best regards,
Krzysztof
PATCH 3/17 dt-bindings: mmc: mtk-sd: add bindings for MT8365 SoC
In reply to Fabien ParentAdd MMC bindings for MT8365 bindings.
--- Documentation/devicetree/bindings/mmc/mtk-sd.yaml | 3 +++ 1 file changed, 3 insertions(+)
Documentation/devicetree/bindings/mmc/mtk-sd.yaml +3 -0
@@ -38,6 +38,9 @@ properties: - items: - const: mediatek,mt8195-mmc - const: mediatek,mt8183-mmc + - items: + - const: mediatek,mt8365-mmc + - const: mediatek,mt8183-mmc reg: minItems: 1
Signature · 1 line
2.36.1
Re: [PATCH 03/17] dt-bindings: mmc: mtk-sd: add bindings for MT8365 SoC
Quoted 12 lines · Fabien Parent
Add MMC bindings for MT8365 bindings.
Signed-off-by Fabien Parent <[email protected]>--- Documentation/devicetree/bindings/mmc/mtk-sd.yaml | 3 +++ 1 file changed, 3 insertions(+)Documentation/devicetree/bindings/mmc/mtk-sd.yaml +0
-0
Documentation/devicetree/bindings/mmc/mtk-sd.yaml properties: · line 42
Quoted 5 lines
Documentation/devicetree/bindings/mmc/mtk-sd.yaml +2
-0@@ -38,6 +38,9 @@ properties: - items: - const: mediatek,mt8195-mmc - const: mediatek,mt8183-mmc + - items: + - const: mediatek,mt8365-mmc
You code it so inconsistently... It's one patchset but each patch doing the same thing differently.
Please put it under enum in entry above.
Best regards,
Krzysztof
PATCH 4/17 dt-bindings: arm: mediatek: Add binding for mt8365-evk board
In reply to Fabien ParentAdd binding documentation for the MT8365-EVK board. The MT8365 EVK board has the following IOs:
* DPI <-> HDMI bridge and HDMI connector.
* 2 audio jack
* 1 USB Type-A Host port
* 2 UART to USB port
* 1 battery connector
* 1 eMMC
* 1 SD card
* 2 camera connectors
* 1 M.2 slot for connectivity
* 1 DSI connector + touchscreen connector
* RPI compatible header
* 1 Ethernet port
--- Documentation/devicetree/bindings/arm/mediatek.yaml | 4 ++++ 1 file changed, 4 insertions(+)
Documentation/devicetree/bindings/arm/mediatek.yaml +4 -0
@@ -216,6 +216,10 @@ properties: - enum: - mediatek,mt8516-pumpkin - const: mediatek,mt8516 + - items: + - enum: + - mediatek,mt8365-evk + - const: mediatek,mt8365 additionalProperties: true
Signature · 1 line
2.36.1
Re: [PATCH 04/17] dt-bindings: arm: mediatek: Add binding for mt8365-evk board
Quoted 25 lines · Fabien Parent
Add binding documentation for the MT8365-EVK board. The MT8365 EVK board has the following IOs:
* DPI <-> HDMI bridge and HDMI connector.
* 2 audio jack
* 1 USB Type-A Host port
* 2 UART to USB port
* 1 battery connector
* 1 eMMC
* 1 SD card
* 2 camera connectors
* 1 M.2 slot for connectivity
* 1 DSI connector + touchscreen connector
* RPI compatible header
* 1 Ethernet portSigned-off-by Fabien Parent <[email protected]>--- Documentation/devicetree/bindings/arm/mediatek.yaml | 4 ++++ 1 file changed, 4 insertions(+)Documentation/devicetree/bindings/arm/mediatek.yaml +0
-0
Documentation/devicetree/bindings/arm/mediatek.yaml properties: · line 218
Quoted 3 lines
Documentation/devicetree/bindings/arm/mediatek.yaml +0
-0@@ -216,6 +216,10 @@ properties: - enum: - mediatek,mt8516-pumpkin - const: mediatek,mt8516
Blank line here
Documentation/devicetree/bindings/arm/mediatek.yaml properties: · line 225
Quoted 7 lines
Documentation/devicetree/bindings/arm/mediatek.yaml +4
-0+ - items: + - enum: + - mediatek,mt8365-evk + - const: mediatek,mt8365 additionalProperties: true
Best regards,
Krzysztof
_______________________________________________
Linux-mediatek mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-mediatek
PATCH 5/17 dt-bindings: dma: mediatek,uart-dma: add MT8365 bindings
In reply to Fabien ParentAdd binding documentation in order to support the MT8365 SoC.
--- Documentation/devicetree/bindings/dma/mediatek,uart-dma.yaml | 1 + 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/dma/mediatek,uart-dma.yaml +1 -0
@@ -22,6 +22,7 @@ properties: - items: - enum: - mediatek,mt2712-uart-dma + - mediatek,mt8365-uart-dma - mediatek,mt8516-uart-dma - const: mediatek,mt6577-uart-dma - enum:
Signature · 1 line
2.36.1
Re: [PATCH 05/17] dt-bindings: dma: mediatek,uart-dma: add MT8365 bindings
Quoted 6 lines · Fabien Parent
Add binding documentation in order to support the MT8365 SoC.
Signed-off-by Fabien Parent <[email protected]>--- Documentation/devicetree/bindings/dma/mediatek,uart-dma.yaml | 1 + 1 file changed, 1 insertion(+)
Best regards,
Krzysztof
Re: [PATCH 05/17] dt-bindings: dma: mediatek,uart-dma: add MT8365 bindings
In reply to Fabien ParentQuoted 1 line · Fabien Parent
Add binding documentation in order to support the MT8365 SoC.
Applied to dmaengine-next, thanks
Quoted 20 lines
Signed-off-by Fabien Parent <[email protected]>--- Documentation/devicetree/bindings/dma/mediatek,uart-dma.yaml | 1 + 1 file changed, 1 insertion(+)Documentation/devicetree/bindings/dma/mediatek,uart-dma.yaml +1
-0@@ -22,6 +22,7 @@ properties: - items: - enum: - mediatek,mt2712-uart-dma + - mediatek,mt8365-uart-dma - mediatek,mt8516-uart-dma - const: mediatek,mt6577-uart-dma - enum:Signature · 1 line
2.36.1
Signature · 1 line
~Vinod
PATCH 6/17 dt-bindings: iio: adc: mediatek: add MT8365 SoC bindings
In reply to Fabien ParentAdd binding for the ADC present in MT8365 SoC.
--- .../devicetree/bindings/iio/adc/mediatek,mt2701-auxadc.yaml | 1 + 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/iio/adc/mediatek,mt2701-auxadc.yaml +1 -0
@@ -37,6 +37,7 @@ properties: - mediatek,mt8186-auxadc - mediatek,mt8195-auxadc - mediatek,mt8516-auxadc + - mediatek,mt8365-auxadc - const: mediatek,mt8173-auxadc reg:
Signature · 1 line
2.36.1
Re: [PATCH 06/17] dt-bindings: iio: adc: mediatek: add MT8365 SoC bindings
Quoted 12 lines · Fabien Parent
Add binding for the ADC present in MT8365 SoC.
Signed-off-by Fabien Parent <[email protected]>--- .../devicetree/bindings/iio/adc/mediatek,mt2701-auxadc.yaml | 1 + 1 file changed, 1 insertion(+)Documentation/devicetree/bindings/iio/adc/mediatek,mt2701-auxadc.yaml +0
-0
Documentation/devicetree/bindings/iio/adc/mediatek,mt2701-auxadc.yaml properties: · line 40
Quoted 4 lines
Documentation/devicetree/bindings/iio/adc/mediatek,mt2701-auxadc.yaml +1
-0@@ -37,6 +37,7 @@ properties: - mediatek,mt8186-auxadc - mediatek,mt8195-auxadc - mediatek,mt8516-auxadc + - mediatek,mt8365-auxadc
Alphabetical order.
Best regards,
Krzysztof
PATCH 7/17 dt-bindings: nvmem: mediatek,efuse: add MT8365 bindings
In reply to Fabien ParentAdd bindings documentation for the efuse driver on MT8365 SoC.
--- Documentation/devicetree/bindings/nvmem/mediatek,efuse.yaml | 1 + 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/nvmem/mediatek,efuse.yaml +1 -0
@@ -32,6 +32,7 @@ properties: - mediatek,mt8192-efuse - mediatek,mt8195-efuse - mediatek,mt8516-efuse + - mediatek,mt8365-efuse - const: mediatek,efuse - const: mediatek,mt8173-efuse deprecated: true
Signature · 1 line
2.36.1
Re: [PATCH 07/17] dt-bindings: nvmem: mediatek,efuse: add MT8365 bindings
Quoted 12 lines · Fabien Parent
Add bindings documentation for the efuse driver on MT8365 SoC.
Signed-off-by Fabien Parent <[email protected]>--- Documentation/devicetree/bindings/nvmem/mediatek,efuse.yaml | 1 + 1 file changed, 1 insertion(+)Documentation/devicetree/bindings/nvmem/mediatek,efuse.yaml +0
-0
Documentation/devicetree/bindings/nvmem/mediatek,efuse.yaml properties: · line 35
Quoted 4 lines
Documentation/devicetree/bindings/nvmem/mediatek,efuse.yaml +1
-0@@ -32,6 +32,7 @@ properties: - mediatek,mt8192-efuse - mediatek,mt8195-efuse - mediatek,mt8516-efuse + - mediatek,mt8365-efuse
Order please
Best regards,
Krzysztof
PATCH 8/17 dt-bindings: watchdog: mtk-wdt: Add MT8365 SoC bindings
In reply to Fabien ParentAdd binding documentation for the MT8365 SoC.
--- Documentation/devicetree/bindings/watchdog/mtk-wdt.txt | 1 + 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/watchdog/mtk-wdt.txt +1 -0
@@ -19,6 +19,7 @@ Required properties: "mediatek,mt8516-wdt", "mediatek,mt6589-wdt": for MT8516 "mediatek,mt8192-wdt": for MT8192 "mediatek,mt8195-wdt", "mediatek,mt6589-wdt": for MT8195 + "mediatek,mt8365-wdt", "mediatek,mt6589-wdt": for MT8365 - reg : Specifies base physical address and size of the registers.
Signature · 1 line
2.36.1
Re: [PATCH 08/17] dt-bindings: watchdog: mtk-wdt: Add MT8365 SoC bindings
Quoted 12 lines · Fabien Parent
Add binding documentation for the MT8365 SoC.
Signed-off-by Fabien Parent <[email protected]>--- Documentation/devicetree/bindings/watchdog/mtk-wdt.txt | 1 + 1 file changed, 1 insertion(+)Documentation/devicetree/bindings/watchdog/mtk-wdt.txt +0
-0
Documentation/devicetree/bindings/watchdog/mtk-wdt.txt Required properties: · line 22
Quoted 4 lines
Documentation/devicetree/bindings/watchdog/mtk-wdt.txt +1
-0@@ -19,6 +19,7 @@ Required properties: "mediatek,mt8516-wdt", "mediatek,mt6589-wdt": for MT8516 "mediatek,mt8192-wdt": for MT8192 "mediatek,mt8195-wdt", "mediatek,mt6589-wdt": for MT8195 + "mediatek,mt8365-wdt", "mediatek,mt6589-wdt": for MT8365
Just for curiosity - how does this (and previous binding patches) depend on your big list:
"This series has dependencies on the following series:"
?
Documentation/devicetree/bindings/watchdog/mtk-wdt.txt Required properties: · line 25
Quoted 3 lines
Documentation/devicetree/bindings/watchdog/mtk-wdt.txt +0
-0- reg : Specifies base physical address and size of the registers.
Best regards,
Krzysztof
Guenter Roeck
maintainerRe: [PATCH 08/17] dt-bindings: watchdog: mtk-wdt: Add MT8365 SoC bindings
In reply to Fabien ParentQuoted 3 lines · Fabien Parent
Add binding documentation for the MT8365 SoC.
Signed-off-by Fabien Parent <[email protected]>
Going through my old e-mails:
This patch never made it upstream and would have to be rewritten to apply to Documentation/devicetree/bindings/watchdog/mediatek,mtk-wdt.yaml.
Guenter
Quoted 16 lines
--- Documentation/devicetree/bindings/watchdog/mtk-wdt.txt | 1 + 1 file changed, 1 insertion(+)Documentation/devicetree/bindings/watchdog/mtk-wdt.txt +1
-0@@ -19,6 +19,7 @@ Required properties: "mediatek,mt8516-wdt", "mediatek,mt6589-wdt": for MT8516 "mediatek,mt8192-wdt": for MT8192 "mediatek,mt8195-wdt", "mediatek,mt6589-wdt": for MT8195 + "mediatek,mt8365-wdt", "mediatek,mt6589-wdt": for MT8365 - reg : Specifies base physical address and size of the registers.
PATCH 9/17 dt-bindings: spi: mt65xx: add MT8365 SoC bindings
In reply to Fabien ParentAdd binding documentation for the MT8365 SoC.
--- Documentation/devicetree/bindings/spi/mediatek,spi-mt65xx.yaml | 1 + 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/spi/mediatek,spi-mt65xx.yaml +1 -0
@@ -18,6 +18,7 @@ properties: - items: - enum: - mediatek,mt7629-spi + - mediatek,mt8365-spi - const: mediatek,mt7622-spi - items: - enum:
Signature · 1 line
2.36.1
Re: [PATCH 09/17] dt-bindings: spi: mt65xx: add MT8365 SoC bindings
Quoted 3 lines · Fabien Parent
Add binding documentation for the MT8365 SoC.
Signed-off-by Fabien Parent <[email protected]>
Best regards,
Krzysztof
PATCH 10/17 dt-bindings: serial: mediatek: add MT8365 bindings
In reply to Fabien ParentAdd binding documentation for the MT8365 SoC.
--- Documentation/devicetree/bindings/serial/mediatek,uart.yaml | 1 + 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/serial/mediatek,uart.yaml +1 -0
@@ -44,6 +44,7 @@ properties: - mediatek,mt8186-uart - mediatek,mt8192-uart - mediatek,mt8195-uart + - mediatek,mt8365-uart - mediatek,mt8516-uart - const: mediatek,mt6577-uart
Signature · 1 line
2.36.1
Re: [PATCH 10/17] dt-bindings: serial: mediatek: add MT8365 bindings
Quoted 6 lines · Fabien Parent
Add binding documentation for the MT8365 SoC.
Signed-off-by Fabien Parent <[email protected]>--- Documentation/devicetree/bindings/serial/mediatek,uart.yaml | 1 + 1 file changed, 1 insertion(+)
Best regards,
Krzysztof
PATCH 11/17 dt-bindings: phy: mediatek,dsi-phy: Add MT8365 SoC bindings
In reply to Fabien ParentAdd binding documentation for the MT8365 SoC.
--- Documentation/devicetree/bindings/phy/mediatek,dsi-phy.yaml | 4 ++++ 1 file changed, 4 insertions(+)
Documentation/devicetree/bindings/phy/mediatek,dsi-phy.yaml +4 -0
@@ -24,6 +24,10 @@ properties: - enum: - mediatek,mt7623-mipi-tx - const: mediatek,mt2701-mipi-tx + - items: + - enum: + - mediatek,mt8365-mipi-tx + - const: mediatek,mt8183-mipi-tx - const: mediatek,mt2701-mipi-tx - const: mediatek,mt8173-mipi-tx - const: mediatek,mt8183-mipi-tx
Signature · 1 line
2.36.1
Re: [PATCH 11/17] dt-bindings: phy: mediatek,dsi-phy: Add MT8365 SoC bindings
Quoted 6 lines · Fabien Parent
Add binding documentation for the MT8365 SoC.
Signed-off-by Fabien Parent <[email protected]>--- Documentation/devicetree/bindings/phy/mediatek,dsi-phy.yaml | 4 ++++ 1 file changed, 4 insertions(+)
Best regards,
Krzysztof
Vinod Koul
maintainerRe: [PATCH 11/17] dt-bindings: phy: mediatek,dsi-phy: Add MT8365 SoC bindings
In reply to Fabien ParentQuoted 1 line · Fabien Parent
Add binding documentation for the MT8365 SoC.
Applied 11, 12 to phy-next, thanks
Signature · 6 lines
~Vinod -- linux-phy mailing list [email protected] https://lists.infradead.org/mailman/listinfo/linux-phy
PATCH 12/17 dt-bindings: phy: mediatek,tphy: add MT8365 SoC bindings
In reply to Fabien ParentAdd binding documentation for the MT8365 SoC.
--- Documentation/devicetree/bindings/phy/mediatek,tphy.yaml | 1 + 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/phy/mediatek,tphy.yaml +1 -0
@@ -82,6 +82,7 @@ properties: - mediatek,mt8183-tphy - mediatek,mt8186-tphy - mediatek,mt8192-tphy + - mediatek,mt8365-tphy - const: mediatek,generic-tphy-v2 - items: - enum:
Signature · 1 line
2.36.1
Re: [PATCH 12/17] dt-bindings: phy: mediatek,tphy: add MT8365 SoC bindings
Quoted 4 lines · Fabien Parent
Add binding documentation for the MT8365 SoC.
Signed-off-by Fabien Parent <[email protected]>---
Best regards,
Krzysztof
PATCH 13/17 dt-bindings: usb: mediatek,mtu3: add MT8365 SoC bindings
In reply to Fabien ParentAdd binding documentation for the MT8365 SoC.
--- Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml | 1 + 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/usb/mediatek,mtu3.yaml +1 -0
@@ -25,6 +25,7 @@ properties: - mediatek,mt8173-mtu3 - mediatek,mt8183-mtu3 - mediatek,mt8192-mtu3 + - mediatek,mt8365-mtu3 - const: mediatek,mtu3 reg:
Signature · 1 line
2.36.1
Re: [PATCH 13/17] dt-bindings: usb: mediatek,mtu3: add MT8365 SoC bindings
Quoted 3 lines · Fabien Parent
Add binding documentation for the MT8365 SoC.
Signed-off-by Fabien Parent <[email protected]>
Best regards,
Krzysztof
PATCH 14/17 dt-bindings: usb: mediatek,mtk-xhci: add MT8365 SoC bindings
In reply to Fabien ParentAdd binding documentation for the MT8365 SoC.
--- Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml | 1 + 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml +1 -0
@@ -33,6 +33,7 @@ properties: - mediatek,mt8186-xhci - mediatek,mt8192-xhci - mediatek,mt8195-xhci + - mediatek,mt8365-xhci - const: mediatek,mtk-xhci reg:
Signature · 1 line
2.36.1
Re: [PATCH 14/17] dt-bindings: usb: mediatek,mtk-xhci: add MT8365 SoC bindings
Quoted 4 lines · Fabien Parent
Add binding documentation for the MT8365 SoC.
Signed-off-by Fabien Parent <[email protected]>---
Best regards,
Krzysztof
PATCH 15/17 arm64: dts: mediatek: add mt6357 device-tree
In reply to Fabien ParentAdd device-tree for the MT6357 PMIC.
--- arch/arm64/boot/dts/mediatek/mt6357.dtsi | 272 +++++++++++++++++++++++ 1 file changed, 272 insertions(+) create mode 100644 arch/arm64/boot/dts/mediatek/mt6357.dtsi
arch/arm64/boot/dts/mediatek/mt6357.dtsi new file +272 -0
@@ -0,0 +1,272 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) 2020 MediaTek Inc. + * Copyright (c) 2020 BayLibre Inc. + */ + +#include <dt-bindings/input/input.h> + +&pwrap { + mt6357_pmic: pmic { + compatible = "mediatek,mt6357"; + + regulators { + mt6357_vproc_reg: buck-vproc { + regulator-name = "vproc"; + regulator-min-microvolt = <518750>; + regulator-max-microvolt = <1312500>; + regulator-ramp-delay = <6250>; + regulator-enable-ramp-delay = <220>; + regulator-always-on; + }; + + mt6357_vcore_reg: buck-vcore { + regulator-name = "vcore"; + regulator-min-microvolt = <518750>; + regulator-max-microvolt = <1312500>; + regulator-ramp-delay = <6250>; + regulator-enable-ramp-delay = <220>; + regulator-always-on; + }; + + mt6357_vmodem_reg: buck-vmodem { + regulator-name = "vmodem"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1193750>; + regulator-ramp-delay = <6250>; + regulator-enable-ramp-delay = <220>; + }; + + mt6357_vs1_reg: buck-vs1 { + regulator-name = "vs1"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <2200000>; + regulator-ramp-delay = <12500>; + regulator-enable-ramp-delay = <220>; + regulator-always-on; + }; + + mt6357_vpa_reg: buck-vpa { + regulator-name = "vpa"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <3650000>; + regulator-ramp-delay = <50000>; + regulator-enable-ramp-delay = <220>; + }; + + mt6357_vfe28_reg: ldo-vfe28 { + compatible = "regulator-fixed"; + regulator-name = "vfe28"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-enable-ramp-delay = <264>; + }; + + mt6357_vxo22_reg: ldo-vxo22 { + regulator-name = "vxo22"; + regulator-min-microvolt = <2200000>; + regulator-max-microvolt = <2400000>; + regulator-enable-ramp-delay = <110>; + }; + + mt6357_vrf18_reg: ldo-vrf18 { + compatible = "regulator-fixed"; + regulator-name = "vrf18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-enable-ramp-delay = <110>; + }; + + mt6357_vrf12_reg: ldo-vrf12 { + compatible = "regulator-fixed"; + regulator-name = "vrf12"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-enable-ramp-delay = <110>; + }; + + mt6357_vefuse_reg: ldo-vefuse { + regulator-name = "vefuse"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <264>; + }; + + mt6357_vcn33_bt_reg: ldo-vcn33-bt { + regulator-name = "vcn33-bt"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3500000>; + regulator-enable-ramp-delay = <264>; + }; + + mt6357_vcn33_wifi_reg: ldo-vcn33-wifi { + regulator-name = "vcn33-wifi"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3500000>; + regulator-enable-ramp-delay = <264>; + }; + + mt6357_vcn28_reg: ldo-vcn28 { + compatible = "regulator-fixed"; + regulator-name = "vcn28"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-enable-ramp-delay = <264>; + }; + + mt6357_vcn18_reg: ldo-vcn18 { + compatible = "regulator-fixed"; + regulator-name = "vcn18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-enable-ramp-delay = <264>; + }; + + mt6357_vcama_reg: ldo-vcama { + regulator-name = "vcama"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2800000>; + regulator-enable-ramp-delay = <264>; + }; + + mt6357_vcamd_reg: ldo-vcamd { + regulator-name = "vcamd"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1800000>; + regulator-enable-ramp-delay = <264>; + }; + + mt6357_vcamio_reg: ldo-vcamio18 { + compatible = "regulator-fixed"; + regulator-name = "vcamio"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-enable-ramp-delay = <264>; + }; + + mt6357_vldo28_reg: ldo-vldo28 { + regulator-name = "vldo28"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <3000000>; + regulator-enable-ramp-delay = <264>; + }; + + mt6357_vsram_others_reg: ldo-vsram-others { + regulator-name = "vsram-others"; + regulator-min-microvolt = <518750>; + regulator-max-microvolt = <1312500>; + regulator-ramp-delay = <6250>; + regulator-enable-ramp-delay = <110>; + regulator-always-on; + }; + + mt6357_vsram_proc_reg: ldo-vsram-proc { + regulator-name = "vsram-proc"; + regulator-min-microvolt = <518750>; + regulator-max-microvolt = <1312500>; + regulator-ramp-delay = <6250>; + regulator-enable-ramp-delay = <110>; + regulator-always-on; + }; + + mt6357_vaux18_reg: ldo-vaux18 { + compatible = "regulator-fixed"; + regulator-name = "vaux18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-enable-ramp-delay = <264>; + }; + + mt6357_vaud28_reg: ldo-vaud28 { + compatible = "regulator-fixed"; + regulator-name = "vaud28"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-enable-ramp-delay = <264>; + }; + + mt6357_vio28_reg: ldo-vio28 { + compatible = "regulator-fixed"; + regulator-name = "vio28"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-enable-ramp-delay = <264>; + }; + + mt6357_vio18_reg: ldo-vio18 { + compatible = "regulator-fixed"; + regulator-name = "vio18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-enable-ramp-delay = <264>; + regulator-always-on; + }; + + mt6357_vdram_reg: ldo-vdram { + regulator-name = "vdram"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1200000>; + regulator-enable-ramp-delay = <3300>; + }; + + mt6357_vmc_reg: ldo-vmc { + regulator-name = "vmc"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <44>; + }; + + mt6357_vmch_reg: ldo-vmch { + regulator-name = "vmch"; + regulator-min-microvolt = <2900000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <44>; + }; + + mt6357_vemc_reg: ldo-vemc { + regulator-name = "vemc"; + regulator-min-microvolt = <2900000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <44>; + regulator-always-on; + }; + + mt6357_vsim1_reg: ldo-vsim1 { + regulator-name = "vsim1"; + regulator-min-microvolt = <1700000>; + regulator-max-microvolt = <3100000>; + regulator-enable-ramp-delay = <264>; + }; + + mt6357_vsim2_reg: ldo-vsim2 { + regulator-name = "vsim2"; + regulator-min-microvolt = <1700000>; + regulator-max-microvolt = <3100000>; + regulator-enable-ramp-delay = <264>; + }; + + mt6357_vibr_reg: ldo-vibr { + regulator-name = "vibr"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-enable-ramp-delay = <44>; + }; + + mt6357_vusb33_reg: ldo-vusb33 { + regulator-name = "vusb33"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3100000>; + regulator-enable-ramp-delay = <264>; + }; + }; + + mt6357rtc: mt6357rtc { + compatible = "mediatek,mt6357-rtc", + "mediatek,mt6358-rtc"; + }; + + mt6357keys: mt6357keys { + compatible = "mediatek,mt6357-keys"; + }; + }; +};
Signature · 1 line
2.36.1
Re: [PATCH 15/17] arm64: dts: mediatek: add mt6357 device-tree
Quoted 8 lines · Fabien Parent
Add device-tree for the MT6357 PMIC.
Signed-off-by Fabien Parent <[email protected]>--- arch/arm64/boot/dts/mediatek/mt6357.dtsi | 272 +++++++++++++++++++++++ 1 file changed, 272 insertions(+) create mode 100644 arch/arm64/boot/dts/mediatek/mt6357.dtsi
(...)
Review
Quoted 2 lines
(quoted diff) +2
-0+ + mt6357rtc: mt6357rtc {
Generic node names, so "rtc".
arch/arm64/boot/dts/mediatek/mt6357.dtsi line 268
Quoted 5 lines
arch/arm64/boot/dts/mediatek/mt6357.dtsi new file +5
-0+ compatible = "mediatek,mt6357-rtc", + "mediatek,mt6358-rtc"; + }; + + mt6357keys: mt6357keys {
Generic node names.
arch/arm64/boot/dts/mediatek/mt6357.dtsi line 272
Quoted 4 lines
arch/arm64/boot/dts/mediatek/mt6357.dtsi new file +4
-0+ compatible = "mediatek,mt6357-keys"; + }; + }; +};
Best regards,
Krzysztof
PATCH 16/17 arm64: dts: mediatek: add mt8365 device-tree
In reply to Fabien ParentAdd device-tree for the MT8365 SoC. More information can be found about that SoC at the following address:
https://www.mediatek.com/products/aiot/i350-mt8365
--- arch/arm64/boot/dts/mediatek/mt8365.dtsi | 1047 ++++++++++++++++++++++ 1 file changed, 1047 insertions(+) create mode 100644 arch/arm64/boot/dts/mediatek/mt8365.dtsi
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1047 -0
@@ -0,0 +1,1047 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Copyright (c) 2018 MediaTek Inc. + */ + +#include <dt-bindings/clock/mediatek,mt8365-clk.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/phy/phy.h> +#include <dt-bindings/power/mt8365-power.h> +#include <dt-bindings/memory/mt8365-larb-port.h> +#include <dt-bindings/thermal/thermal.h> + +/ { + compatible = "mediatek,mt8365"; + interrupt-parent = <&sysirq>; + #address-cells = <2>; + #size-cells = <2>; + + aliases { + ovl0 = &ovl0; + rdma0 = &rdma0; + rdma1 = &rdma1; + color0 = &color0; + ccorr0 = &ccorr0; + aal0 = &aal0; + gamma0 = &gamma0; + dither0 = &dither0; + dsi0 = &dsi0; + dpi0 = &dpi0; + }; + + cpus: cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu-map { + cluster0: cluster0 { + core0 { + cpu = <&cpu0>; + }; + core1 { + cpu = <&cpu1>; + }; + core2 { + cpu = <&cpu2>; + }; + core3 { + cpu = <&cpu3>; + }; + }; + }; + + cpu0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x0>; + clock-frequency = <1600000000>; + clocks = <&mcucfg CLK_MCU_BUS_SEL>, + <&apmixedsys CLK_APMIXED_MAINPLL>; + clock-names = "cpu", "intermediate"; + operating-points-v2 = <&cluster0_opp>; + #cooling-cells = <2>; + enable-method = "psci"; + }; + + cpu1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x1>; + clock-frequency = <1600000000>; + clocks = <&mcucfg CLK_MCU_BUS_SEL>, + <&apmixedsys CLK_APMIXED_MAINPLL>; + clock-names = "cpu", "intermediate", "armpll"; + operating-points-v2 = <&cluster0_opp>; + #cooling-cells = <2>; + enable-method = "psci"; + }; + + cpu2: cpu@2 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x2>; + clock-frequency = <1600000000>; + clocks = <&mcucfg CLK_MCU_BUS_SEL>, + <&apmixedsys CLK_APMIXED_MAINPLL>; + clock-names = "cpu", "intermediate", "armpll"; + operating-points-v2 = <&cluster0_opp>; + #cooling-cells = <2>; + enable-method = "psci"; + }; + + cpu3: cpu@3 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x3>; + clock-frequency = <1600000000>; + clocks = <&mcucfg CLK_MCU_BUS_SEL>, + <&apmixedsys CLK_APMIXED_MAINPLL>; + clock-names = "cpu", "intermediate", "armpll"; + operating-points-v2 = <&cluster0_opp>; + #cooling-cells = <2>; + enable-method = "psci"; + }; + }; + + cluster0_opp: opp-table-0 { + compatible = "operating-points-v2"; + opp-shared; + opp-850000000 { + opp-hz = /bits/ 64 <850000000>; + opp-microvolt = <650000>; + }; + opp-918000000 { + opp-hz = /bits/ 64 <918000000>; + opp-microvolt = <668750>; + }; + opp-987000000 { + opp-hz = /bits/ 64 <987000000>; + opp-microvolt = <687500>; + }; + opp-1056000000 { + opp-hz = /bits/ 64 <1056000000>; + opp-microvolt = <706250>; + }; + opp-1125000000 { + opp-hz = /bits/ 64 <1125000000>; + opp-microvolt = <725000>; + }; + opp-1216000000 { + opp-hz = /bits/ 64 <1216000000>; + opp-microvolt = <750000>; + }; + opp-1308000000 { + opp-hz = /bits/ 64 <1308000000>; + opp-microvolt = <775000>; + }; + opp-1400000000 { + opp-hz = /bits/ 64 <1400000000>; + opp-microvolt = <800000>; + }; + opp-1466000000 { + opp-hz = /bits/ 64 <1466000000>; + opp-microvolt = <825000>; + }; + opp-1533000000 { + opp-hz = /bits/ 64 <1533000000>; + opp-microvolt = <850000>; + }; + opp-1633000000 { + opp-hz = /bits/ 64 <1633000000>; + opp-microvolt = <887500>; + }; + opp-1700000000 { + opp-hz = /bits/ 64 <1700000000>; + opp-microvolt = <912500>; + }; + opp-1767000000 { + opp-hz = /bits/ 64 <1767000000>; + opp-microvolt = <937500>; + }; + opp-1834000000 { + opp-hz = /bits/ 64 <1834000000>; + opp-microvolt = <962500>; + }; + opp-1917000000 { + opp-hz = /bits/ 64 <1917000000>; + opp-microvolt = <993750>; + }; + opp-2001000000 { + opp-hz = /bits/ 64 <2001000000>; + opp-microvolt = <1025000>; + }; + }; + + clk26m: oscillator { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <26000000>; + clock-output-names = "clk26m"; + }; + + psci { + compatible = "arm,psci-1.0"; + method = "smc"; + }; + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + /* 128 KiB reserved for ARM Trusted Firmware (BL31) */ + bl31_secmon_reserved: secmon@43000000 { + no-map; + reg = <0 0x43000000 0 0x20000>; + }; + }; + + soc { + #address-cells = <2>; + #size-cells = <2>; + compatible = "simple-bus"; + ranges; + + gic: interrupt-controller@c000000 { + compatible = "arm,gic-v3"; + #interrupt-cells = <4>; + interrupt-parent = <&gic>; + interrupt-controller; + reg = <0 0x0c000000 0 0x80000>, + <0 0x0c080000 0 0x80000>; + + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH 0>; + }; + + topckgen: syscon@10000000 { + compatible = "mediatek,mt8365-topckgen", "syscon"; + reg = <0 0x10000000 0 0x1000>; + #clock-cells = <1>; + }; + + infracfg: syscon@10001000 { + compatible = "mediatek,mt8365-infracfg", "syscon"; + reg = <0 0x10001000 0 0x1000>; + #clock-cells = <1>; + }; + + pericfg: syscon@10003000 { + compatible = "mediatek,mt8365-pericfg", "syscon"; + reg = <0 0x10003000 0 0x1000>; + #clock-cells = <1>; + }; + + syscfg_pctl: syscfg-pctl@10005000 { + compatible = "syscon"; + reg = <0 0x10005000 0 0x1000>; + }; + + scpsys: syscon@10006000 { + compatible = "syscon", "simple-mfd"; + reg = <0 0x10006000 0 0x1000>; + #power-domain-cells = <1>; + + /* System Power Manager */ + spm: power-controller { + compatible = "mediatek,mt8365-power-controller"; + #address-cells = <1>; + #size-cells = <0>; + #power-domain-cells = <1>; + + /* power domains of the SoC */ + power-domain@MT8365_POWER_DOMAIN_MM { + reg = <MT8365_POWER_DOMAIN_MM>; + clocks = <&topckgen CLK_TOP_MM_SEL>, + <&mmsys CLK_MM_MM_SMI_COMMON>, + <&mmsys CLK_MM_MM_SMI_COMM0>, + <&mmsys CLK_MM_MM_SMI_COMM1>, + <&mmsys CLK_MM_MM_SMI_LARB0>; + clock-names = "mm", "mm-0", "mm-1", + "mm-2", "mm-3"; + #power-domain-cells = <0>; + mediatek,infracfg = <&infracfg>; + mediatek,infracfg_nao = <&infracfg_nao>; + #address-cells = <1>; + #size-cells = <0>; + + power-domain@MT8365_POWER_DOMAIN_CAM { + reg = <MT8365_POWER_DOMAIN_CAM>; + clocks = <&camsys CLK_CAM_LARB2>, + <&camsys CLK_CAM_SENIF>, + <&camsys CLK_CAMSV0>, + <&camsys CLK_CAMSV1>, + <&camsys CLK_CAM_FDVT>, + <&camsys CLK_CAM_WPE>; + clock-names = "cam-0", "cam-1", + "cam-2", "cam-3", + "cam-4", "cam-5"; + #power-domain-cells = <0>; + mediatek,infracfg = <&infracfg>; + mediatek,smi = <&smi_common>; + }; + + power-domain@MT8365_POWER_DOMAIN_VDEC { + reg = <MT8365_POWER_DOMAIN_VDEC>; + #power-domain-cells = <0>; + mediatek,smi = <&smi_common>; + }; + + power-domain@MT8365_POWER_DOMAIN_VENC { + reg = <MT8365_POWER_DOMAIN_VENC>; + #power-domain-cells = <0>; + mediatek,smi = <&smi_common>; + }; + + power-domain@MT8365_POWER_DOMAIN_APU { + reg = <MT8365_POWER_DOMAIN_APU>; + clocks = <&infracfg CLK_IFR_APU_AXI>, + <&apu CLK_APU_IPU_CK>, + <&apu CLK_APU_AXI>, + <&apu CLK_APU_JTAG>, + <&apu CLK_APU_IF_CK>, + <&apu CLK_APU_EDMA>, + <&apu CLK_APU_AHB>; + clock-names = "apu", "apu-0", + "apu-1", "apu-2", + "apu-3", "apu-4", + "apu-5"; + #power-domain-cells = <0>; + mediatek,infracfg = <&infracfg>; + mediatek,smi = <&smi_common>; + }; + }; + + power-domain@MT8365_POWER_DOMAIN_CONN { + reg = <MT8365_POWER_DOMAIN_CONN>; + clocks = <&topckgen CLK_TOP_CONN_32K>, + <&topckgen CLK_TOP_CONN_26M>; + clock-names = "conn", "conn1"; + #power-domain-cells = <0>; + mediatek,infracfg = <&infracfg>; + }; + + power-domain@MT8365_POWER_DOMAIN_MFG { + reg = <MT8365_POWER_DOMAIN_MFG>; + clocks = <&topckgen CLK_TOP_MFG_SEL>; + clock-names = "mfg"; + #power-domain-cells = <0>; + mediatek,infracfg = <&infracfg>; + }; + + power-domain@MT8365_POWER_DOMAIN_AUDIO { + reg = <MT8365_POWER_DOMAIN_AUDIO>; + clocks = <&topckgen CLK_TOP_AUD_INTBUS_SEL>, + <&infracfg CLK_IFR_AUDIO>, + <&infracfg CLK_IFR_AUD_26M_BK>; + clock-names = "audio", "audio1", "audio2"; + #power-domain-cells = <0>; + mediatek,infracfg = <&infracfg>; + }; + + power-domain@MT8365_POWER_DOMAIN_DSP { + reg = <MT8365_POWER_DOMAIN_DSP>; + clocks = <&topckgen CLK_TOP_DSP_SEL>, + <&topckgen CLK_TOP_DSP_26M>; + clock-names = "dsp", "dsp1"; + #power-domain-cells = <0>; + mediatek,infracfg = <&infracfg>; + }; + }; + }; + + watchdog: watchdog@10007000 { + compatible = "mediatek,mt8365-wdt", + "mediatek,mt6589-wdt"; + reg = <0 0x10007000 0 0x100>; + #reset-cells = <1>; + }; + + gpt: apxgpt@10008000 { + compatible = "mediatek,mt8365-timer", + "mediatek,mt6577-timer"; + reg = <0 0x10008000 0 0x1000>; + interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_LOW>; + clocks = <&topckgen CLK_TOP_SYS_26M_D2>; + clock-names = "clk13m"; + }; + + pio: pinctrl@1000b000 { + compatible = "mediatek,mt8365-pinctrl"; + reg = <0 0x1000b000 0 0x1000>; + mediatek,pctl-regmap = <&syscfg_pctl>; + pins-are-numbered; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>; + }; + + apmixedsys: syscon@1000c000 { + compatible = "mediatek,mt8365-apmixedsys", "syscon"; + reg = <0 0x1000c000 0 0x1000>; + #clock-cells = <1>; + }; + + pwrap: pwrap@1000d000 { + compatible = "mediatek,mt8365-pwrap"; + reg = <0 0x1000d000 0 0x1000>; + reg-names = "pwrap"; + interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&infracfg CLK_IFR_PWRAP_SPI>, + <&infracfg CLK_IFR_PMIC_AP>, + <&infracfg CLK_IFR_PWRAP_SYS>, + <&infracfg CLK_IFR_PWRAP_TMR>; + clock-names = "spi", "wrap", "sys", "tmr"; + }; + + keypad: kp@10010000 { + compatible = "mediatek,mt6779-keypad"; + reg = <0 0x10010000 0 0x1000>; + wakeup-source; + interrupts = <GIC_SPI 124 IRQ_TYPE_EDGE_FALLING>; + clocks = <&clk26m>; + clock-names = "kpd"; + status = "disabled"; + }; + + mcucfg: syscon@10200000 { + compatible = "mediatek,mt8365-mcucfg", "syscon"; + reg = <0 0x10200000 0 0x2000>; + #clock-cells = <1>; + }; + + sysirq: intpol-controller@10200a80 { + compatible = "mediatek,mt8365-sysirq", + "mediatek,mt6577-sysirq"; + interrupt-controller; + #interrupt-cells = <3>; + interrupt-parent = <&gic>; + reg = <0 0x10200a80 0 0x20>; + }; + + iommu: iommu@10205000 { + compatible = "mediatek,mt8365-m4u"; + reg = <0 0x10205000 0 0x1000>; + interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_LOW>; + mediatek,larbs = <&larb0>, <&larb1>, <&larb2>, <&larb3>; + #iommu-cells = <1>; + }; + + infracfg_nao: infracfg-nao@1020e000 { + compatible = "syscon"; + reg = <0 0x1020e000 0 0x1000>; + }; + + rng: rng@1020f000 { + compatible = "mediatek,mt8365-rng", + "mediatek,mt7623-rng"; + reg = <0 0x1020f000 0 0x100>; + clocks = <&infracfg CLK_IFR_TRNG>; + clock-names = "rng"; + }; + + apdma: dma-controller@11000280 { + compatible = "mediatek,mt8365-uart-dma", + "mediatek,mt6577-uart-dma"; + reg = <0 0x11000280 0 0x80>, + <0 0x11000300 0 0x80>, + <0 0x11000380 0 0x80>, + <0 0x11000400 0 0x80>, + <0 0x11000580 0 0x80>, + <0 0x11000600 0 0x80>; + interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 46 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 47 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 48 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 51 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 52 IRQ_TYPE_LEVEL_LOW>; + dma-requests = <6>; + clocks = <&infracfg CLK_IFR_AP_DMA>; + clock-names = "apdma"; + #dma-cells = <1>; + }; + + auxadc: adc@11001000 { + compatible = "mediatek,mt8365-auxadc", + "mediatek,mt8173-auxadc"; + reg = <0 0x11001000 0 0x1000>; + clocks = <&infracfg CLK_IFR_AUXADC>; + clock-names = "main"; + #io-channel-cells = <1>; + }; + + uart0: serial@11002000 { + compatible = "mediatek,mt8365-uart", + "mediatek,mt6577-uart"; + reg = <0 0x11002000 0 0x1000>; + interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_LOW>; + clocks = <&clk26m>, <&infracfg CLK_IFR_UART0>; + clock-names = "baud", "bus"; + dmas = <&apdma 0 + &apdma 1>; + dma-names = "tx", "rx"; + status = "disabled"; + }; + + uart1: serial@11003000 { + compatible = "mediatek,mt8365-uart", + "mediatek,mt6577-uart"; + reg = <0 0x11003000 0 0x1000>; + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_LOW>; + clocks = <&clk26m>, <&infracfg CLK_IFR_UART1>; + clock-names = "baud", "bus"; + dmas = <&apdma 2 + &apdma 3>; + dma-names = "tx", "rx"; + status = "disabled"; + }; + + uart2: serial@11004000 { + compatible = "mediatek,mt8365-uart", + "mediatek,mt6577-uart"; + reg = <0 0x11004000 0 0x1000>; + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_LOW>; + clocks = <&clk26m>, <&infracfg CLK_IFR_UART2>; + clock-names = "baud", "bus"; + dmas = <&apdma 4 + &apdma 5>; + dma-names = "tx", "rx"; + status = "disabled"; + }; + + pwm: pwm@11006000 { + compatible = "mediatek,mt8365-pwm"; + reg = <0 0x11006000 0 0x1000>; + #pwm-cells = <2>; + interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_LOW>; + clocks = <&infracfg CLK_IFR_PWM_HCLK>, + <&infracfg CLK_IFR_PWM>, + <&infracfg CLK_IFR_PWM1>, + <&infracfg CLK_IFR_PWM2>, + <&infracfg CLK_IFR_PWM3>; + clock-names = "top", "main", "pwm1", "pwm2", "pwm3"; + }; + + i2c0: i2c@11007000 { + compatible = "mediatek,mt8365-i2c", + "mediatek,mt8168-i2c"; + reg = <0 0x11007000 0 0xa0>, + <0 0x11000080 0 0x80>; + interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_LOW>; + clock-div = <1>; + clocks = <&infracfg CLK_IFR_I2C0_AXI>, + <&infracfg CLK_IFR_AP_DMA>; + clock-names = "main", "dma"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c1: i2c@11008000 { + compatible = "mediatek,mt8365-i2c", + "mediatek,mt8168-i2c"; + reg = <0 0x11008000 0 0xa0>, + <0 0x11000100 0 0x80>; + interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_LOW>; + clock-div = <1>; + clocks = <&infracfg CLK_IFR_I2C1_AXI>, + <&infracfg CLK_IFR_AP_DMA>; + clock-names = "main", "dma"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c2: i2c@11009000 { + compatible = "mediatek,mt8365-i2c", + "mediatek,mt8168-i2c"; + reg = <0 0x11009000 0 0xa0>, + <0 0x11000180 0 0x80>; + interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_LOW>; + clock-div = <1>; + clocks = <&infracfg CLK_IFR_I2C2_AXI>, + <&infracfg CLK_IFR_AP_DMA>; + clock-names = "main", "dma"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + spi: spi@1100a000 { + compatible = "mediatek,mt8365-spi", + "mediatek,mt7622-spi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0 0x1100a000 0 0x100>; + interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_LOW>; + clocks = <&topckgen CLK_TOP_UNIVPLL2_D4>, + <&topckgen CLK_TOP_SPI_SEL>, + <&infracfg CLK_IFR_SPI0>; + clock-names = "parent-clk", "sel-clk", "spi-clk"; + status = "disabled"; + }; + + thermal: thermal@1100b000 { + compatible = "mediatek,mt8365-thermal"; + reg = <0 0x1100b000 0 0x1000>; + interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_LOW>; + clocks = <&infracfg CLK_IFR_THERM>, + <&infracfg CLK_IFR_AUXADC>; + clock-names = "therm", "auxadc"; + mediatek,auxadc = <&auxadc>; + mediatek,apmixedsys = <&apmixedsys>; + nvmem-cells = <&thermal_calibration>; + nvmem-cell-names = "calibration-data"; + #thermal-sensor-cells = <1>; + }; + + disp_pwm: disp-pwm@1100e000 { + compatible = "mediatek,mt8365-disp-pwm", + "mediatek,mt8183-disp-pwm"; + reg = <0 0x1100e000 0 0x1000>; + #pwm-cells = <2>; + clocks = <&topckgen CLK_TOP_DISP_PWM_SEL>, + <&infracfg CLK_IFR_DISP_PWM>; + clock-names = "main", "mm"; + power-domains = <&spm MT8365_POWER_DOMAIN_MM>; + status = "disabled"; + }; + + i2c3: i2c@1100f000 { + compatible = "mediatek,mt8365-i2c", + "mediatek,mt8168-i2c"; + reg = <0 0x1100f000 0 0xa0>, + <0 0x11000200 0 0x80>; + interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_LOW>; + clock-div = <1>; + clocks = <&infracfg CLK_IFR_I2C3_AXI>, + <&infracfg CLK_IFR_AP_DMA>; + clock-names = "main", "dma"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + ssusb: usb@11201000 { + compatible = "mediatek,mt8365-mtu3", "mediatek,mtu3"; + reg = <0 0x11201000 0 0x2e00>, + <0 0x11203e00 0 0x0100>; + reg-names = "mac", "ippc"; + interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_LOW>; + phys = <&u2port0 PHY_TYPE_USB2>, + <&u2port1 PHY_TYPE_USB2>; + clocks = <&topckgen CLK_TOP_SSUSB_TOP_CK_EN>, + <&infracfg CLK_IFR_SSUSB_REF>, + <&infracfg CLK_IFR_SSUSB_SYS>, + <&infracfg CLK_IFR_ICUSB>; + clock-names = "sys_ck", "ref_ck", "mcu_ck", + "dma_ck"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + status = "disabled"; + + usb_host: usb@11200000 { + compatible = "mediatek,mt8365-xhci", + "mediatek,mtk-xhci"; + reg = <0 0x11200000 0 0x1000>; + reg-names = "mac"; + interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_LOW>; + clocks = <&topckgen CLK_TOP_SSUSB_TOP_CK_EN>, + <&infracfg CLK_IFR_SSUSB_REF>, + <&infracfg CLK_IFR_SSUSB_SYS>, + <&infracfg CLK_IFR_ICUSB>, + <&infracfg CLK_IFR_SSUSB_XHCI>; + clock-names = "sys_ck", "ref_ck", "mcu_ck", + "dma_ck", "xhci_ck"; + status = "disabled"; + }; + }; + + mmc0: mmc@11230000 { + compatible = "mediatek,mt8365-mmc", "mediatek,mt8183-mmc"; + reg = <0 0x11230000 0 0x1000>, + <0 0x11cd0000 0 0x1000>; + interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_LOW>; + clocks = <&topckgen CLK_TOP_MSDC50_0_SEL>, + <&infracfg CLK_IFR_MSDC0_HCLK>, + <&infracfg CLK_IFR_MSDC0_SRC>; + clock-names = "source", "hclk", "source_cg"; + status = "disabled"; + }; + + mmc1: mmc@11240000 { + compatible = "mediatek,mt8365-mmc", "mediatek,mt8183-mmc"; + reg = <0 0x11240000 0 0x1000>, + <0 0x11c90000 0 0x1000>; + interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_LOW>; + clocks = <&topckgen CLK_TOP_MSDC30_1_SEL>, + <&infracfg CLK_IFR_MSDC1_HCLK>, + <&infracfg CLK_IFR_MSDC1_SRC>; + clock-names = "source", "hclk", "source_cg"; + status = "disabled"; + }; + + ethernet: ethernet@112a0000 { + compatible = "mediatek,mt8365-eth"; + reg = <0 0x112a0000 0 0x1000>; + mediatek,pericfg = <&infracfg>; + interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&topckgen CLK_TOP_ETH_SEL>, + <&infracfg CLK_IFR_NIC_AXI>, + <&infracfg CLK_IFR_NIC_SLV_AXI>; + clock-names = "core", "reg", "trans"; + status = "disabled"; + }; + + mipi_tx0: dsi-phy@11c00000 { + compatible = "mediatek,mt8365-mipi-tx", + "mediatek,mt8183-mipi-tx"; + reg = <0 0x11c00000 0 0x800>; + clocks = <&clk26m>; + clock-names = "ref_clk"; + #clock-cells = <0>; + #phy-cells = <0>; + clock-output-names = "mipi_tx0_pll"; + }; + + efuse: efuse@11c50000 { + compatible = "mediatek,mt8365-efuse", "mediatek,efuse"; + reg = <0 0x11c50000 0 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + + thermal_calibration: calib@180 { + reg = <0x180 0xc>; + }; + }; + + u3phy: t-phy@11cc0000 { + compatible = "mediatek,mt8365-tphy", + "mediatek,generic-tphy-v2"; + #address-cells = <2>; + #phy-cells = <1>; + #size-cells = <2>; + ranges; + status = "okay"; + + u2port0: usb-phy@11cc0000 { + reg = <0 0x11cc0000 0 0x400>; + clocks = <&topckgen CLK_TOP_SSUSB_PHY_CK_EN>, + <&topckgen CLK_TOP_USB20_48M_EN>; + clock-names = "ref", "da_ref"; + #phy-cells = <1>; + status = "okay"; + }; + + u2port1: usb-phy@11cc1000 { + reg = <0 0x11cc1000 0 0x400>; + clocks = <&topckgen CLK_TOP_SSUSB_PHY_CK_EN>, + <&topckgen CLK_TOP_USB20_48M_EN>; + clock-names = "ref", "da_ref"; + #phy-cells = <1>; + status = "okay"; + }; + }; + + mfgcfg: syscon@13000000 { + compatible = "mediatek,mt8365-mfgcfg", "syscon"; + reg = <0 0x13000000 0 0x1000>; + #clock-cells = <1>; + }; + + mmsys: syscon@14000000 { + compatible = "mediatek,mt8365-mmsys", "syscon"; + reg = <0 0x14000000 0 0x1000>; + #clock-cells = <1>; + }; + + mutex: mutex@14001000 { + compatible = "mediatek,mt8365-disp-mutex"; + reg = <0 0x14001000 0 0x1000>; + interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&spm MT8365_POWER_DOMAIN_MM>; + }; + + smi_common: smi@14002000 { + compatible = "mediatek,mt8365-smi-common", + "mediatek,mt8186-smi-common"; + reg = <0 0x14002000 0 0x1000>; + clocks = <&mmsys CLK_MM_MM_SMI_COMMON>, + <&mmsys CLK_MM_MM_SMI_COMMON>, + <&mmsys CLK_MM_MM_SMI_COMM0>, + <&mmsys CLK_MM_MM_SMI_COMM1>; + clock-names = "apb", "smi", "gals0", "gals1"; + power-domains = <&spm MT8365_POWER_DOMAIN_MM>; + }; + + larb0: larb@14003000 { + compatible = "mediatek,mt8365-smi-larb", + "mediatek,mt8186-smi-larb"; + reg = <0 0x14003000 0 0x1000>; + mediatek,smi = <&smi_common>; + clocks = <&mmsys CLK_MM_MM_SMI_LARB0>, + <&mmsys CLK_MM_MM_SMI_LARB0>; + clock-names = "apb", "smi"; + power-domains = <&spm MT8365_POWER_DOMAIN_MM>; + mediatek,larb-id = <0>; + }; + + ovl0: ovl@1400b000 { + compatible = "mediatek,mt8365-disp-ovl", + "mediatek,mt8192-disp-ovl"; + reg = <0 0x1400b000 0 0x1000>; + interrupts = <GIC_SPI 161 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&spm MT8365_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_MM_DISP_OVL0>; + iommus = <&iommu M4U_PORT_DISP_OVL0>; + }; + + rdma0: rdma@1400d000 { + compatible = "mediatek,mt8365-disp-rdma", + "mediatek,mt8183-disp-rdma"; + reg = <0 0x1400d000 0 0x1000>; + interrupts = <GIC_SPI 162 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&spm MT8365_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_MM_DISP_RDMA0>; + iommus = <&iommu M4U_PORT_DISP_RDMA0>; + mediatek,rdma-fifo-size = <5120>; + }; + + color0: color@1400f000 { + compatible = "mediatek,mt8365-disp-color", + "mediatek,mt8173-disp-color"; + reg = <0 0x1400f000 0 0x1000>; + interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&spm MT8365_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_MM_DISP_COLOR0>; + }; + + ccorr0: ccorr@14010000 { + compatible = "mediatek,mt8365-disp-ccorr", + "mediatek,mt8183-disp-ccorr"; + reg = <0 0x14010000 0 0x1000>; + interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&spm MT8365_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_MM_DISP_CCORR0>; + }; + + aal0: aal@14011000 { + compatible = "mediatek,mt8365-disp-aal", + "mediatek,mt8183-disp-aal"; + reg = <0 0x14011000 0 0x1000>; + interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&spm MT8365_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_MM_DISP_AAL0>; + }; + + gamma0: gamma@14012000 { + compatible = "mediatek,mt8365-disp-gamma", + "mediatek,mt8183-disp-gamma"; + reg = <0 0x14012000 0 0x1000>; + interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&spm MT8365_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_MM_DISP_GAMMA0>; + }; + + dither0: dither@14013000 { + compatible = "mediatek,mt8365-disp-dither", + "mediatek,mt8183-disp-dither"; + reg = <0 0x14013000 0 0x1000>; + interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&spm MT8365_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_MM_DISP_DITHER0>; + }; + + dsi0: dsi@14014000 { + compatible = "mediatek,mt8365-dsi", + "mediatek,mt8183-dsi"; + reg = <0 0x14014000 0 0x1000>; + interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&spm MT8365_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_MM_DSI0>, + <&mmsys CLK_MM_DSI0_DIG_DSI>, + <&mipi_tx0>; + clock-names = "engine", "digital", "hs"; + phys = <&mipi_tx0>; + phy-names = "dphy"; + status = "disabled"; + }; + + rdma1: rdma@14016000 { + compatible = "mediatek,mt8365-disp-rdma", + "mediatek,mt8183-disp-rdma"; + reg = <0 0x14016000 0 0x1000>; + interrupts = <GIC_SPI 195 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&spm MT8365_POWER_DOMAIN_MM>; + clocks = <&mmsys CLK_MM_MM_DISP_RDMA1>; + iommus = <&iommu M4U_PORT_DISP_RDMA1>; + mediatek,rdma-fifo-size = <2048>; + }; + + dpi0: dpi@14018000 { + compatible = "mediatek,mt8365-dpi", + "mediatek,mt8192-dpi"; + reg = <0 0x14018000 0 0x1000>; + interrupts = <GIC_SPI 197 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&spm MT8365_POWER_DOMAIN_MM>; + clocks = <&topckgen CLK_TOP_DPI0_SEL>, + <&mmsys CLK_MM_MM_DPI0>, + <&apmixedsys CLK_APMIXED_LVDSPLL>, + <&mmsys CLK_MM_DPI0_DPI0>; + clock-names = "pixel", "engine", "pll", "dpi"; + status = "disabled"; + }; + + camsys: syscon@15000000 { + compatible = "mediatek,mt8365-imgsys", "syscon"; + reg = <0 0x15000000 0 0x1000>; + #clock-cells = <1>; + }; + + larb2: larb@15001000 { + compatible = "mediatek,mt8365-smi-larb", + "mediatek,mt8186-smi-larb"; + reg = <0 0x15001000 0 0x1000>; + mediatek,smi = <&smi_common>; + clocks = <&mmsys CLK_MM_MM_SMI_IMG>, + <&camsys CLK_CAM_LARB2>; + clock-names = "apb", "smi"; + power-domains = <&spm MT8365_POWER_DOMAIN_CAM>; + mediatek,larb-id = <2>; + }; + + vdecsys: syscon@16000000 { + compatible = "mediatek,mt8365-vdecsys", "syscon"; + reg = <0 0x16000000 0 0x1000>; + #clock-cells = <1>; + }; + + larb3: larb@16010000 { + compatible = "mediatek,mt8365-smi-larb", + "mediatek,mt8186-smi-larb"; + reg = <0 0x16010000 0 0x1000>; + mediatek,smi = <&smi_common>; + clocks = <&vdecsys CLK_VDEC_LARB1>, + <&vdecsys CLK_VDEC_LARB1>; + clock-names = "apb", "smi"; + power-domains = <&spm MT8365_POWER_DOMAIN_VDEC>; + mediatek,larb-id = <3>; + }; + + vencsys: syscon@17000000 { + compatible = "mediatek,mt8365-vencsys", "syscon"; + reg = <0 0x17000000 0 0x1000>; + #clock-cells = <1>; + }; + + larb1: larb@17010000 { + compatible = "mediatek,mt8365-smi-larb", + "mediatek,mt8186-smi-larb"; + reg = <0 0x17010000 0 0x1000>; + mediatek,smi = <&smi_common>; + clocks = <&vencsys CLK_VENC>, <&vencsys CLK_VENC>; + clock-names = "apb", "smi"; + power-domains = <&spm MT8365_POWER_DOMAIN_VENC>; + mediatek,larb-id = <1>; + }; + + apu: syscon@19020000 { + compatible = "mediatek,mt8365-apu", "syscon"; + reg = <0 0x19020000 0 0x1000>; + #clock-cells = <1>; + }; + }; + + thermal-zones { + cpu_thermal: cpu-thermal { + polling-delay-passive = <1000>; /* milliseconds */ + polling-delay = <1000>; /* milliseconds */ + thermal-sensors = <&thermal 0>; + + trips { + threshold: trip-point0 { + temperature = <95000>; + hysteresis = <2000>; + type = "passive"; + }; + + target: trip-point1 { + temperature = <105000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu_crit: cpu_crit0 { + temperature = <117000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&target>; + cooling-device = + <&cpu0 + THERMAL_NO_LIMIT + THERMAL_NO_LIMIT>, + <&cpu1 + THERMAL_NO_LIMIT + THERMAL_NO_LIMIT>, + <&cpu2 + THERMAL_NO_LIMIT + THERMAL_NO_LIMIT>, + <&cpu3 + THERMAL_NO_LIMIT + THERMAL_NO_LIMIT>; + contribution = <100>; + }; + }; + }; + + tzts1: tzts1-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&thermal 1>; + trips {}; + cooling-maps {}; + }; + + tzts2: tzts2-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&thermal 2>; + trips {}; + cooling-maps {}; + }; + + tzts3: tzts3-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&thermal 3>; + trips {}; + cooling-maps {}; + }; + + tzts4: tzts4-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&thermal 4>; + trips {}; + cooling-maps {}; + }; + }; + + + timer { + compatible = "arm,armv8-timer"; + interrupt-parent = <&gic>; + interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW 0>, + <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW 0>, + <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW 0>, + <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW 0>; + }; +};
Signature · 1 line
2.36.1
Re: [PATCH 16/17] arm64: dts: mediatek: add mt8365 device-tree
Quoted 185 lines · Fabien Parent
Add device-tree for the MT8365 SoC. More information can be found about that SoC at the following address:
https://www.mediatek.com/products/aiot/i350-mt8365Signed-off-by Fabien Parent <[email protected]>--- arch/arm64/boot/dts/mediatek/mt8365.dtsi | 1047 ++++++++++++++++++++++ 1 file changed, 1047 insertions(+) create mode 100644 arch/arm64/boot/dts/mediatek/mt8365.dtsiarch/arm64/boot/dts/mediatek/mt8365.dtsi new file +169
-0@@ -0,0 +1,1047 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Copyright (c) 2018 MediaTek Inc. + */ + +#include <dt-bindings/clock/mediatek,mt8365-clk.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/phy/phy.h> +#include <dt-bindings/power/mt8365-power.h> +#include <dt-bindings/memory/mt8365-larb-port.h> +#include <dt-bindings/thermal/thermal.h> + +/ { + compatible = "mediatek,mt8365"; + interrupt-parent = <&sysirq>; + #address-cells = <2>; + #size-cells = <2>; + + aliases { + ovl0 = &ovl0; + rdma0 = &rdma0; + rdma1 = &rdma1; + color0 = &color0; + ccorr0 = &ccorr0; + aal0 = &aal0; + gamma0 = &gamma0; + dither0 = &dither0; + dsi0 = &dsi0; + dpi0 = &dpi0; + }; + + cpus: cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu-map { + cluster0: cluster0 { + core0 { + cpu = <&cpu0>; + }; + core1 { + cpu = <&cpu1>; + }; + core2 { + cpu = <&cpu2>; + }; + core3 { + cpu = <&cpu3>; + }; + }; + }; + + cpu0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x0>; + clock-frequency = <1600000000>; + clocks = <&mcucfg CLK_MCU_BUS_SEL>, + <&apmixedsys CLK_APMIXED_MAINPLL>; + clock-names = "cpu", "intermediate"; + operating-points-v2 = <&cluster0_opp>; + #cooling-cells = <2>; + enable-method = "psci"; + }; + + cpu1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x1>; + clock-frequency = <1600000000>; + clocks = <&mcucfg CLK_MCU_BUS_SEL>, + <&apmixedsys CLK_APMIXED_MAINPLL>; + clock-names = "cpu", "intermediate", "armpll"; + operating-points-v2 = <&cluster0_opp>; + #cooling-cells = <2>; + enable-method = "psci"; + }; + + cpu2: cpu@2 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x2>; + clock-frequency = <1600000000>; + clocks = <&mcucfg CLK_MCU_BUS_SEL>, + <&apmixedsys CLK_APMIXED_MAINPLL>; + clock-names = "cpu", "intermediate", "armpll"; + operating-points-v2 = <&cluster0_opp>; + #cooling-cells = <2>; + enable-method = "psci"; + }; + + cpu3: cpu@3 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x3>; + clock-frequency = <1600000000>; + clocks = <&mcucfg CLK_MCU_BUS_SEL>, + <&apmixedsys CLK_APMIXED_MAINPLL>; + clock-names = "cpu", "intermediate", "armpll"; + operating-points-v2 = <&cluster0_opp>; + #cooling-cells = <2>; + enable-method = "psci"; + }; + }; + + cluster0_opp: opp-table-0 { + compatible = "operating-points-v2"; + opp-shared; + opp-850000000 { + opp-hz = /bits/ 64 <850000000>; + opp-microvolt = <650000>; + }; + opp-918000000 { + opp-hz = /bits/ 64 <918000000>; + opp-microvolt = <668750>; + }; + opp-987000000 { + opp-hz = /bits/ 64 <987000000>; + opp-microvolt = <687500>; + }; + opp-1056000000 { + opp-hz = /bits/ 64 <1056000000>; + opp-microvolt = <706250>; + }; + opp-1125000000 { + opp-hz = /bits/ 64 <1125000000>; + opp-microvolt = <725000>; + }; + opp-1216000000 { + opp-hz = /bits/ 64 <1216000000>; + opp-microvolt = <750000>; + }; + opp-1308000000 { + opp-hz = /bits/ 64 <1308000000>; + opp-microvolt = <775000>; + }; + opp-1400000000 { + opp-hz = /bits/ 64 <1400000000>; + opp-microvolt = <800000>; + }; + opp-1466000000 { + opp-hz = /bits/ 64 <1466000000>; + opp-microvolt = <825000>; + }; + opp-1533000000 { + opp-hz = /bits/ 64 <1533000000>; + opp-microvolt = <850000>; + }; + opp-1633000000 { + opp-hz = /bits/ 64 <1633000000>; + opp-microvolt = <887500>; + }; + opp-1700000000 { + opp-hz = /bits/ 64 <1700000000>; + opp-microvolt = <912500>; + }; + opp-1767000000 { + opp-hz = /bits/ 64 <1767000000>; + opp-microvolt = <937500>; + }; + opp-1834000000 { + opp-hz = /bits/ 64 <1834000000>; + opp-microvolt = <962500>; + }; + opp-1917000000 { + opp-hz = /bits/ 64 <1917000000>; + opp-microvolt = <993750>; + };
arch/arm64/boot/dts/mediatek/mt8365.dtsi line 179
Quoted 10 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +10
-0+ opp-2001000000 { + opp-hz = /bits/ 64 <2001000000>; + opp-microvolt = <1025000>; + }; + }; + + clk26m: oscillator { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <26000000>;
This does not look like property of a SoC. Are you sure MT8365 SoC has this clock (not the board)?
Quoted 19 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +19
-0+ clock-output-names = "clk26m"; + }; + + psci { + compatible = "arm,psci-1.0"; + method = "smc"; + }; + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + /* 128 KiB reserved for ARM Trusted Firmware (BL31) */ + bl31_secmon_reserved: secmon@43000000 { + no-map; + reg = <0 0x43000000 0 0x20000>; + }; + };
arch/arm64/boot/dts/mediatek/mt8365.dtsi line 208
Quoted 10 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +10
-0+ + soc { + #address-cells = <2>; + #size-cells = <2>; + compatible = "simple-bus"; + ranges; + + gic: interrupt-controller@c000000 { + compatible = "arm,gic-v3"; + #interrupt-cells = <4>;
Why do you have four cells here (and passing 0 as interrupt)?
Quoted 17 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +17
-0+ interrupt-parent = <&gic>; + interrupt-controller; + reg = <0 0x0c000000 0 0x80000>, + <0 0x0c080000 0 0x80000>; + + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH 0>; + }; + + topckgen: syscon@10000000 { + compatible = "mediatek,mt8365-topckgen", "syscon"; + reg = <0 0x10000000 0 0x1000>; + #clock-cells = <1>; + }; + + infracfg: syscon@10001000 { + compatible = "mediatek,mt8365-infracfg", "syscon"; + reg = <0 0x10001000 0 0x1000>;
arch/arm64/boot/dts/mediatek/mt8365.dtsi line 235
Quoted 10 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +10
-0+ #clock-cells = <1>; + }; + + pericfg: syscon@10003000 { + compatible = "mediatek,mt8365-pericfg", "syscon"; + reg = <0 0x10003000 0 0x1000>; + #clock-cells = <1>; + }; + + syscfg_pctl: syscfg-pctl@10005000 {
This is I guess also syscon, like other nodes?
arch/arm64/boot/dts/mediatek/mt8365.dtsi line 236
Quoted 1 line
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ compatible = "syscon";
You need specific compatible. Please run make dtbs_check and fix the errors.
arch/arm64/boot/dts/mediatek/mt8365.dtsi line 241
Quoted 5 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +5
-0+ reg = <0 0x10005000 0 0x1000>; + }; + + scpsys: syscon@10006000 { + compatible = "syscon", "simple-mfd";
You need specific compatible.
arch/arm64/boot/dts/mediatek/mt8365.dtsi line 243
Quoted 2 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +2
-0+ reg = <0 0x10006000 0 0x1000>; + #power-domain-cells = <1>;
This is definitely wrong now. It's not a simple-mfd device, so please do not use that property.
arch/arm64/boot/dts/mediatek/mt8365.dtsi line 252
Quoted 9 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +9
-0+ + /* System Power Manager */ + spm: power-controller { + compatible = "mediatek,mt8365-power-controller"; + #address-cells = <1>; + #size-cells = <0>; + #power-domain-cells = <1>; + + /* power domains of the SoC */
The comment suggests you will later add here power domains not for the SoC. If that's not true, just skip the comment.
Quoted 98 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +98
-0+ power-domain@MT8365_POWER_DOMAIN_MM { + reg = <MT8365_POWER_DOMAIN_MM>; + clocks = <&topckgen CLK_TOP_MM_SEL>, + <&mmsys CLK_MM_MM_SMI_COMMON>, + <&mmsys CLK_MM_MM_SMI_COMM0>, + <&mmsys CLK_MM_MM_SMI_COMM1>, + <&mmsys CLK_MM_MM_SMI_LARB0>; + clock-names = "mm", "mm-0", "mm-1", + "mm-2", "mm-3"; + #power-domain-cells = <0>; + mediatek,infracfg = <&infracfg>; + mediatek,infracfg_nao = <&infracfg_nao>; + #address-cells = <1>; + #size-cells = <0>; + + power-domain@MT8365_POWER_DOMAIN_CAM { + reg = <MT8365_POWER_DOMAIN_CAM>; + clocks = <&camsys CLK_CAM_LARB2>, + <&camsys CLK_CAM_SENIF>, + <&camsys CLK_CAMSV0>, + <&camsys CLK_CAMSV1>, + <&camsys CLK_CAM_FDVT>, + <&camsys CLK_CAM_WPE>; + clock-names = "cam-0", "cam-1", + "cam-2", "cam-3", + "cam-4", "cam-5"; + #power-domain-cells = <0>; + mediatek,infracfg = <&infracfg>; + mediatek,smi = <&smi_common>; + }; + + power-domain@MT8365_POWER_DOMAIN_VDEC { + reg = <MT8365_POWER_DOMAIN_VDEC>; + #power-domain-cells = <0>; + mediatek,smi = <&smi_common>; + }; + + power-domain@MT8365_POWER_DOMAIN_VENC { + reg = <MT8365_POWER_DOMAIN_VENC>; + #power-domain-cells = <0>; + mediatek,smi = <&smi_common>; + }; + + power-domain@MT8365_POWER_DOMAIN_APU { + reg = <MT8365_POWER_DOMAIN_APU>; + clocks = <&infracfg CLK_IFR_APU_AXI>, + <&apu CLK_APU_IPU_CK>, + <&apu CLK_APU_AXI>, + <&apu CLK_APU_JTAG>, + <&apu CLK_APU_IF_CK>, + <&apu CLK_APU_EDMA>, + <&apu CLK_APU_AHB>; + clock-names = "apu", "apu-0", + "apu-1", "apu-2", + "apu-3", "apu-4", + "apu-5"; + #power-domain-cells = <0>; + mediatek,infracfg = <&infracfg>; + mediatek,smi = <&smi_common>; + }; + }; + + power-domain@MT8365_POWER_DOMAIN_CONN { + reg = <MT8365_POWER_DOMAIN_CONN>; + clocks = <&topckgen CLK_TOP_CONN_32K>, + <&topckgen CLK_TOP_CONN_26M>; + clock-names = "conn", "conn1"; + #power-domain-cells = <0>; + mediatek,infracfg = <&infracfg>; + }; + + power-domain@MT8365_POWER_DOMAIN_MFG { + reg = <MT8365_POWER_DOMAIN_MFG>; + clocks = <&topckgen CLK_TOP_MFG_SEL>; + clock-names = "mfg"; + #power-domain-cells = <0>; + mediatek,infracfg = <&infracfg>; + }; + + power-domain@MT8365_POWER_DOMAIN_AUDIO { + reg = <MT8365_POWER_DOMAIN_AUDIO>; + clocks = <&topckgen CLK_TOP_AUD_INTBUS_SEL>, + <&infracfg CLK_IFR_AUDIO>, + <&infracfg CLK_IFR_AUD_26M_BK>; + clock-names = "audio", "audio1", "audio2"; + #power-domain-cells = <0>; + mediatek,infracfg = <&infracfg>; + }; + + power-domain@MT8365_POWER_DOMAIN_DSP { + reg = <MT8365_POWER_DOMAIN_DSP>; + clocks = <&topckgen CLK_TOP_DSP_SEL>, + <&topckgen CLK_TOP_DSP_26M>; + clock-names = "dsp", "dsp1"; + #power-domain-cells = <0>; + mediatek,infracfg = <&infracfg>; + }; + };
arch/arm64/boot/dts/mediatek/mt8365.dtsi line 360
Quoted 10 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +10
-0+ }; + + watchdog: watchdog@10007000 { + compatible = "mediatek,mt8365-wdt", + "mediatek,mt6589-wdt"; + reg = <0 0x10007000 0 0x100>; + #reset-cells = <1>; + }; + + gpt: apxgpt@10008000 {
Generic node names, so "timer"
Quoted 29 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +29
-0+ compatible = "mediatek,mt8365-timer", + "mediatek,mt6577-timer"; + reg = <0 0x10008000 0 0x1000>; + interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_LOW>; + clocks = <&topckgen CLK_TOP_SYS_26M_D2>; + clock-names = "clk13m"; + }; + + pio: pinctrl@1000b000 { + compatible = "mediatek,mt8365-pinctrl"; + reg = <0 0x1000b000 0 0x1000>; + mediatek,pctl-regmap = <&syscfg_pctl>; + pins-are-numbered; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>; + }; + + apmixedsys: syscon@1000c000 { + compatible = "mediatek,mt8365-apmixedsys", "syscon"; + reg = <0 0x1000c000 0 0x1000>; + #clock-cells = <1>; + }; + + pwrap: pwrap@1000d000 { + compatible = "mediatek,mt8365-pwrap"; + reg = <0 0x1000d000 0 0x1000>;
arch/arm64/boot/dts/mediatek/mt8365.dtsi line 399
Quoted 10 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +10
-0+ reg-names = "pwrap"; + interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&infracfg CLK_IFR_PWRAP_SPI>, + <&infracfg CLK_IFR_PMIC_AP>, + <&infracfg CLK_IFR_PWRAP_SYS>, + <&infracfg CLK_IFR_PWRAP_TMR>; + clock-names = "spi", "wrap", "sys", "tmr"; + }; + + keypad: kp@10010000 {
s/kp/keypad/
Quoted 6 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +6
-0+ compatible = "mediatek,mt6779-keypad"; + reg = <0 0x10010000 0 0x1000>; + wakeup-source; + interrupts = <GIC_SPI 124 IRQ_TYPE_EDGE_FALLING>; + clocks = <&clk26m>; + clock-names = "kpd";
arch/arm64/boot/dts/mediatek/mt8365.dtsi line 415
Quoted 10 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +10
-0+ status = "disabled"; + }; + + mcucfg: syscon@10200000 { + compatible = "mediatek,mt8365-mcucfg", "syscon"; + reg = <0 0x10200000 0 0x2000>; + #clock-cells = <1>; + }; + + sysirq: intpol-controller@10200a80 {
interrupt-controller
Quoted 7 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +7
-0+ compatible = "mediatek,mt8365-sysirq", + "mediatek,mt6577-sysirq"; + interrupt-controller; + #interrupt-cells = <3>; + interrupt-parent = <&gic>; + reg = <0 0x10200a80 0 0x20>; + };
arch/arm64/boot/dts/mediatek/mt8365.dtsi line 432
Quoted 10 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +10
-0+ + iommu: iommu@10205000 { + compatible = "mediatek,mt8365-m4u"; + reg = <0 0x10205000 0 0x1000>; + interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_LOW>; + mediatek,larbs = <&larb0>, <&larb1>, <&larb2>, <&larb3>; + #iommu-cells = <1>; + }; + + infracfg_nao: infracfg-nao@1020e000 {
Other nodes are named syscon
arch/arm64/boot/dts/mediatek/mt8365.dtsi line 433
Quoted 1 line
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ compatible = "syscon";
No, syscon cannot be alone.
Quoted 40 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +40
-0+ reg = <0 0x1020e000 0 0x1000>; + }; + + rng: rng@1020f000 { + compatible = "mediatek,mt8365-rng", + "mediatek,mt7623-rng"; + reg = <0 0x1020f000 0 0x100>; + clocks = <&infracfg CLK_IFR_TRNG>; + clock-names = "rng"; + }; + + apdma: dma-controller@11000280 { + compatible = "mediatek,mt8365-uart-dma", + "mediatek,mt6577-uart-dma"; + reg = <0 0x11000280 0 0x80>, + <0 0x11000300 0 0x80>, + <0 0x11000380 0 0x80>, + <0 0x11000400 0 0x80>, + <0 0x11000580 0 0x80>, + <0 0x11000600 0 0x80>; + interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 46 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 47 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 48 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 51 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 52 IRQ_TYPE_LEVEL_LOW>; + dma-requests = <6>; + clocks = <&infracfg CLK_IFR_AP_DMA>; + clock-names = "apdma"; + #dma-cells = <1>; + }; + + auxadc: adc@11001000 { + compatible = "mediatek,mt8365-auxadc", + "mediatek,mt8173-auxadc"; + reg = <0 0x11001000 0 0x1000>; + clocks = <&infracfg CLK_IFR_AUXADC>; + clock-names = "main"; + #io-channel-cells = <1>; + };
arch/arm64/boot/dts/mediatek/mt8365.dtsi line 483
Quoted 10 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +10
-0+ + uart0: serial@11002000 { + compatible = "mediatek,mt8365-uart", + "mediatek,mt6577-uart"; + reg = <0 0x11002000 0 0x1000>; + interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_LOW>; + clocks = <&clk26m>, <&infracfg CLK_IFR_UART0>; + clock-names = "baud", "bus"; + dmas = <&apdma 0 + &apdma 1>;
You need to split these into two phandles.
arch/arm64/boot/dts/mediatek/mt8365.dtsi line 496
Quoted 13 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +13
-0+ dma-names = "tx", "rx"; + status = "disabled"; + }; + + uart1: serial@11003000 { + compatible = "mediatek,mt8365-uart", + "mediatek,mt6577-uart"; + reg = <0 0x11003000 0 0x1000>; + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_LOW>; + clocks = <&clk26m>, <&infracfg CLK_IFR_UART1>; + clock-names = "baud", "bus"; + dmas = <&apdma 2 + &apdma 3>;
Ditto.
Quoted 71 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +71
-0+ dma-names = "tx", "rx"; + status = "disabled"; + }; + + uart2: serial@11004000 { + compatible = "mediatek,mt8365-uart", + "mediatek,mt6577-uart"; + reg = <0 0x11004000 0 0x1000>; + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_LOW>; + clocks = <&clk26m>, <&infracfg CLK_IFR_UART2>; + clock-names = "baud", "bus"; + dmas = <&apdma 4 + &apdma 5>; + dma-names = "tx", "rx"; + status = "disabled"; + }; + + pwm: pwm@11006000 { + compatible = "mediatek,mt8365-pwm"; + reg = <0 0x11006000 0 0x1000>; + #pwm-cells = <2>; + interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_LOW>; + clocks = <&infracfg CLK_IFR_PWM_HCLK>, + <&infracfg CLK_IFR_PWM>, + <&infracfg CLK_IFR_PWM1>, + <&infracfg CLK_IFR_PWM2>, + <&infracfg CLK_IFR_PWM3>; + clock-names = "top", "main", "pwm1", "pwm2", "pwm3"; + }; + + i2c0: i2c@11007000 { + compatible = "mediatek,mt8365-i2c", + "mediatek,mt8168-i2c"; + reg = <0 0x11007000 0 0xa0>, + <0 0x11000080 0 0x80>; + interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_LOW>; + clock-div = <1>; + clocks = <&infracfg CLK_IFR_I2C0_AXI>, + <&infracfg CLK_IFR_AP_DMA>; + clock-names = "main", "dma"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c1: i2c@11008000 { + compatible = "mediatek,mt8365-i2c", + "mediatek,mt8168-i2c"; + reg = <0 0x11008000 0 0xa0>, + <0 0x11000100 0 0x80>; + interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_LOW>; + clock-div = <1>; + clocks = <&infracfg CLK_IFR_I2C1_AXI>, + <&infracfg CLK_IFR_AP_DMA>; + clock-names = "main", "dma"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c2: i2c@11009000 { + compatible = "mediatek,mt8365-i2c", + "mediatek,mt8168-i2c"; + reg = <0 0x11009000 0 0xa0>, + <0 0x11000180 0 0x80>; + interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_LOW>; + clock-div = <1>; + clocks = <&infracfg CLK_IFR_I2C2_AXI>, + <&infracfg CLK_IFR_AP_DMA>; + clock-names = "main", "dma"; + #address-cells = <1>;
arch/arm64/boot/dts/mediatek/mt8365.dtsi line 577
Quoted 10 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +10
-0+ #size-cells = <0>; + status = "disabled"; + }; + + spi: spi@1100a000 { + compatible = "mediatek,mt8365-spi", + "mediatek,mt7622-spi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0 0x1100a000 0 0x100>;
Reg goes after compatible.
Quoted 13 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +13
-0+ interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_LOW>; + clocks = <&topckgen CLK_TOP_UNIVPLL2_D4>, + <&topckgen CLK_TOP_SPI_SEL>, + <&infracfg CLK_IFR_SPI0>; + clock-names = "parent-clk", "sel-clk", "spi-clk"; + status = "disabled"; + }; + + thermal: thermal@1100b000 { + compatible = "mediatek,mt8365-thermal"; + reg = <0 0x1100b000 0 0x1000>; + interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_LOW>; + clocks = <&infracfg CLK_IFR_THERM>,
arch/arm64/boot/dts/mediatek/mt8365.dtsi line 600
Quoted 10 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +10
-0+ <&infracfg CLK_IFR_AUXADC>; + clock-names = "therm", "auxadc"; + mediatek,auxadc = <&auxadc>; + mediatek,apmixedsys = <&apmixedsys>; + nvmem-cells = <&thermal_calibration>; + nvmem-cell-names = "calibration-data"; + #thermal-sensor-cells = <1>; + }; + + disp_pwm: disp-pwm@1100e000 {
Generic node names, so "pwm"
Quoted 111 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +111
-0+ compatible = "mediatek,mt8365-disp-pwm", + "mediatek,mt8183-disp-pwm"; + reg = <0 0x1100e000 0 0x1000>; + #pwm-cells = <2>; + clocks = <&topckgen CLK_TOP_DISP_PWM_SEL>, + <&infracfg CLK_IFR_DISP_PWM>; + clock-names = "main", "mm"; + power-domains = <&spm MT8365_POWER_DOMAIN_MM>; + status = "disabled"; + }; + + i2c3: i2c@1100f000 { + compatible = "mediatek,mt8365-i2c", + "mediatek,mt8168-i2c"; + reg = <0 0x1100f000 0 0xa0>, + <0 0x11000200 0 0x80>; + interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_LOW>; + clock-div = <1>; + clocks = <&infracfg CLK_IFR_I2C3_AXI>, + <&infracfg CLK_IFR_AP_DMA>; + clock-names = "main", "dma"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + ssusb: usb@11201000 { + compatible = "mediatek,mt8365-mtu3", "mediatek,mtu3"; + reg = <0 0x11201000 0 0x2e00>, + <0 0x11203e00 0 0x0100>; + reg-names = "mac", "ippc"; + interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_LOW>; + phys = <&u2port0 PHY_TYPE_USB2>, + <&u2port1 PHY_TYPE_USB2>; + clocks = <&topckgen CLK_TOP_SSUSB_TOP_CK_EN>, + <&infracfg CLK_IFR_SSUSB_REF>, + <&infracfg CLK_IFR_SSUSB_SYS>, + <&infracfg CLK_IFR_ICUSB>; + clock-names = "sys_ck", "ref_ck", "mcu_ck", + "dma_ck"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + status = "disabled"; + + usb_host: usb@11200000 { + compatible = "mediatek,mt8365-xhci", + "mediatek,mtk-xhci"; + reg = <0 0x11200000 0 0x1000>; + reg-names = "mac"; + interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_LOW>; + clocks = <&topckgen CLK_TOP_SSUSB_TOP_CK_EN>, + <&infracfg CLK_IFR_SSUSB_REF>, + <&infracfg CLK_IFR_SSUSB_SYS>, + <&infracfg CLK_IFR_ICUSB>, + <&infracfg CLK_IFR_SSUSB_XHCI>; + clock-names = "sys_ck", "ref_ck", "mcu_ck", + "dma_ck", "xhci_ck"; + status = "disabled"; + }; + }; + + mmc0: mmc@11230000 { + compatible = "mediatek,mt8365-mmc", "mediatek,mt8183-mmc"; + reg = <0 0x11230000 0 0x1000>, + <0 0x11cd0000 0 0x1000>; + interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_LOW>; + clocks = <&topckgen CLK_TOP_MSDC50_0_SEL>, + <&infracfg CLK_IFR_MSDC0_HCLK>, + <&infracfg CLK_IFR_MSDC0_SRC>; + clock-names = "source", "hclk", "source_cg"; + status = "disabled"; + }; + + mmc1: mmc@11240000 { + compatible = "mediatek,mt8365-mmc", "mediatek,mt8183-mmc"; + reg = <0 0x11240000 0 0x1000>, + <0 0x11c90000 0 0x1000>; + interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_LOW>; + clocks = <&topckgen CLK_TOP_MSDC30_1_SEL>, + <&infracfg CLK_IFR_MSDC1_HCLK>, + <&infracfg CLK_IFR_MSDC1_SRC>; + clock-names = "source", "hclk", "source_cg"; + status = "disabled"; + }; + + ethernet: ethernet@112a0000 { + compatible = "mediatek,mt8365-eth"; + reg = <0 0x112a0000 0 0x1000>; + mediatek,pericfg = <&infracfg>; + interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&topckgen CLK_TOP_ETH_SEL>, + <&infracfg CLK_IFR_NIC_AXI>, + <&infracfg CLK_IFR_NIC_SLV_AXI>; + clock-names = "core", "reg", "trans"; + status = "disabled"; + }; + + mipi_tx0: dsi-phy@11c00000 { + compatible = "mediatek,mt8365-mipi-tx", + "mediatek,mt8183-mipi-tx"; + reg = <0 0x11c00000 0 0x800>; + clocks = <&clk26m>; + clock-names = "ref_clk"; + #clock-cells = <0>; + #phy-cells = <0>; + clock-output-names = "mipi_tx0_pll"; + }; + + efuse: efuse@11c50000 { + compatible = "mediatek,mt8365-efuse", "mediatek,efuse";
arch/arm64/boot/dts/mediatek/mt8365.dtsi line 721
Quoted 10 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +10
-0+ reg = <0 0x11c50000 0 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + + thermal_calibration: calib@180 { + reg = <0x180 0xc>; + }; + }; + + u3phy: t-phy@11cc0000 {
s/t-phy/phy/
arch/arm64/boot/dts/mediatek/mt8365.dtsi line 725
Quoted 4 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +4
-0+ compatible = "mediatek,mt8365-tphy", + "mediatek,generic-tphy-v2"; + #address-cells = <2>; + #phy-cells = <1>;
address-cells, then size, then phy
arch/arm64/boot/dts/mediatek/mt8365.dtsi line 728
Quoted 3 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +3
-0+ #size-cells = <2>; + ranges; + status = "okay";
No need for status ok.
arch/arm64/boot/dts/mediatek/mt8365.dtsi line 736
Quoted 8 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +8
-0+ + u2port0: usb-phy@11cc0000 { + reg = <0 0x11cc0000 0 0x400>; + clocks = <&topckgen CLK_TOP_SSUSB_PHY_CK_EN>, + <&topckgen CLK_TOP_USB20_48M_EN>; + clock-names = "ref", "da_ref"; + #phy-cells = <1>; + status = "okay";
Ditto
Quoted 22 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +22
-0+ }; + + u2port1: usb-phy@11cc1000 { + reg = <0 0x11cc1000 0 0x400>; + clocks = <&topckgen CLK_TOP_SSUSB_PHY_CK_EN>, + <&topckgen CLK_TOP_USB20_48M_EN>; + clock-names = "ref", "da_ref"; + #phy-cells = <1>; + status = "okay"; + }; + }; + + mfgcfg: syscon@13000000 { + compatible = "mediatek,mt8365-mfgcfg", "syscon"; + reg = <0 0x13000000 0 0x1000>; + #clock-cells = <1>; + }; + + mmsys: syscon@14000000 { + compatible = "mediatek,mt8365-mmsys", "syscon"; + reg = <0 0x14000000 0 0x1000>; + #clock-cells = <1>;
arch/arm64/boot/dts/mediatek/mt8365.dtsi line 768
Quoted 10 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +10
-0+ }; + + mutex: mutex@14001000 { + compatible = "mediatek,mt8365-disp-mutex"; + reg = <0 0x14001000 0 0x1000>; + interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&spm MT8365_POWER_DOMAIN_MM>; + }; + + smi_common: smi@14002000 {
s/smi/memory-controller/ in node name?
arch/arm64/boot/dts/mediatek/mt8365.dtsi line 780
Quoted 12 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +12
-0+ compatible = "mediatek,mt8365-smi-common", + "mediatek,mt8186-smi-common"; + reg = <0 0x14002000 0 0x1000>; + clocks = <&mmsys CLK_MM_MM_SMI_COMMON>, + <&mmsys CLK_MM_MM_SMI_COMMON>, + <&mmsys CLK_MM_MM_SMI_COMM0>, + <&mmsys CLK_MM_MM_SMI_COMM1>; + clock-names = "apb", "smi", "gals0", "gals1"; + power-domains = <&spm MT8365_POWER_DOMAIN_MM>; + }; + + larb0: larb@14003000 {
The same?
arch/arm64/boot/dts/mediatek/mt8365.dtsi line 788
Quoted 8 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +8
-0+ compatible = "mediatek,mt8365-smi-larb", + "mediatek,mt8186-smi-larb"; + reg = <0 0x14003000 0 0x1000>; + mediatek,smi = <&smi_common>; + clocks = <&mmsys CLK_MM_MM_SMI_LARB0>, + <&mmsys CLK_MM_MM_SMI_LARB0>; + clock-names = "apb", "smi"; + power-domains = <&spm MT8365_POWER_DOMAIN_MM>;
Best regards,
Krzysztof
Chunfeng Yun
maintainerRe: [PATCH 16/17] arm64: dts: mediatek: add mt8365 device-tree
Quoted 871 lines · Krzysztof Kozlowski
Quoted 187 lines · Fabien Parent
Add device-tree for the MT8365 SoC. More information can be found about that SoC at the following address:
https://www.mediatek.com/products/aiot/i350-mt8365Signed-off-by Fabien Parent <[email protected]>--- arch/arm64/boot/dts/mediatek/mt8365.dtsi | 1047 ++++++++++++++++++++++ 1 file changed, 1047 insertions(+) create mode 100644 arch/arm64/boot/dts/mediatek/mt8365.dtsiarch/arm64/boot/dts/mediatek/mt8365.dtsi new file +169
-0@@ -0,0 +1,1047 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Copyright (c) 2018 MediaTek Inc. + */ + +#include <dt-bindings/clock/mediatek,mt8365-clk.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/phy/phy.h> +#include <dt-bindings/power/mt8365-power.h> +#include <dt-bindings/memory/mt8365-larb-port.h> +#include <dt-bindings/thermal/thermal.h> + +/ { + compatible = "mediatek,mt8365"; + interrupt-parent = <&sysirq>; + #address-cells = <2>; + #size-cells = <2>; + + aliases { + ovl0 = &ovl0; + rdma0 = &rdma0; + rdma1 = &rdma1; + color0 = &color0; + ccorr0 = &ccorr0; + aal0 = &aal0; + gamma0 = &gamma0; + dither0 = &dither0; + dsi0 = &dsi0; + dpi0 = &dpi0; + }; + + cpus: cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu-map { + cluster0: cluster0 { + core0 { + cpu = <&cpu0>; + }; + core1 { + cpu = <&cpu1>; + }; + core2 { + cpu = <&cpu2>; + }; + core3 { + cpu = <&cpu3>; + }; + }; + }; + + cpu0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x0>; + clock-frequency = <1600000000>; + clocks = <&mcucfg CLK_MCU_BUS_SEL>, + <&apmixedsys CLK_APMIXED_MAINPLL>; + clock-names = "cpu", "intermediate"; + operating-points-v2 = <&cluster0_opp>; + #cooling-cells = <2>; + enable-method = "psci"; + }; + + cpu1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x1>; + clock-frequency = <1600000000>; + clocks = <&mcucfg CLK_MCU_BUS_SEL>, + <&apmixedsys CLK_APMIXED_MAINPLL>; + clock-names = "cpu", "intermediate", "armpll"; + operating-points-v2 = <&cluster0_opp>; + #cooling-cells = <2>; + enable-method = "psci"; + }; + + cpu2: cpu@2 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x2>; + clock-frequency = <1600000000>; + clocks = <&mcucfg CLK_MCU_BUS_SEL>, + <&apmixedsys CLK_APMIXED_MAINPLL>; + clock-names = "cpu", "intermediate", "armpll"; + operating-points-v2 = <&cluster0_opp>; + #cooling-cells = <2>; + enable-method = "psci"; + }; + + cpu3: cpu@3 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x3>; + clock-frequency = <1600000000>; + clocks = <&mcucfg CLK_MCU_BUS_SEL>, + <&apmixedsys CLK_APMIXED_MAINPLL>; + clock-names = "cpu", "intermediate", "armpll"; + operating-points-v2 = <&cluster0_opp>; + #cooling-cells = <2>; + enable-method = "psci"; + }; + }; + + cluster0_opp: opp-table-0 { + compatible = "operating-points-v2"; + opp-shared; + opp-850000000 { + opp-hz = /bits/ 64 <850000000>; + opp-microvolt = <650000>; + }; + opp-918000000 { + opp-hz = /bits/ 64 <918000000>; + opp-microvolt = <668750>; + }; + opp-987000000 { + opp-hz = /bits/ 64 <987000000>; + opp-microvolt = <687500>; + }; + opp-1056000000 { + opp-hz = /bits/ 64 <1056000000>; + opp-microvolt = <706250>; + }; + opp-1125000000 { + opp-hz = /bits/ 64 <1125000000>; + opp-microvolt = <725000>; + }; + opp-1216000000 { + opp-hz = /bits/ 64 <1216000000>; + opp-microvolt = <750000>; + }; + opp-1308000000 { + opp-hz = /bits/ 64 <1308000000>; + opp-microvolt = <775000>; + }; + opp-1400000000 { + opp-hz = /bits/ 64 <1400000000>; + opp-microvolt = <800000>; + }; + opp-1466000000 { + opp-hz = /bits/ 64 <1466000000>; + opp-microvolt = <825000>; + }; + opp-1533000000 { + opp-hz = /bits/ 64 <1533000000>; + opp-microvolt = <850000>; + }; + opp-1633000000 { + opp-hz = /bits/ 64 <1633000000>; + opp-microvolt = <887500>; + }; + opp-1700000000 { + opp-hz = /bits/ 64 <1700000000>; + opp-microvolt = <912500>; + }; + opp-1767000000 { + opp-hz = /bits/ 64 <1767000000>; + opp-microvolt = <937500>; + }; + opp-1834000000 { + opp-hz = /bits/ 64 <1834000000>; + opp-microvolt = <962500>; + }; + opp-1917000000 { + opp-hz = /bits/ 64 <1917000000>; + opp-microvolt = <993750>; + };arch/arm64/boot/dts/mediatek/mt8365.dtsi line 179
Quoted 10 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +10
-0+ opp-2001000000 { + opp-hz = /bits/ 64 <2001000000>; + opp-microvolt = <1025000>; + }; + }; + + clk26m: oscillator { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <26000000>;This does not look like property of a SoC. Are you sure MT8365 SoC has
this clock (not the board)?Quoted 19 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +19
-0+ clock-output-names = "clk26m"; + }; + + psci { + compatible = "arm,psci-1.0"; + method = "smc"; + }; + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + /* 128 KiB reserved for ARM Trusted Firmware (BL31) */ + bl31_secmon_reserved: secmon@43000000 { + no-map; + reg = <0 0x43000000 0 0x20000>; + }; + };arch/arm64/boot/dts/mediatek/mt8365.dtsi line 208
Quoted 10 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +10
-0+ + soc { + #address-cells = <2>; + #size-cells = <2>; + compatible = "simple-bus"; + ranges; + + gic: interrupt-controller@c000000 { + compatible = "arm,gic-v3"; + #interrupt-cells = <4>;Why do you have four cells here (and passing 0 as interrupt)?
Quoted 25 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +10
-0+ interrupt-parent = <&gic>; + interrupt-controller; + reg = <0 0x0c000000 0 0x80000>, + <0 0x0c080000 0 0x80000>; + + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH 0>; + }; + + topckgen: syscon@10000000 { + compatible = "mediatek,mt8365-topckgen","syscon";
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +6
-0+ reg = <0 0x10000000 0 0x1000>; + #clock-cells = <1>; + }; + + infracfg: syscon@10001000 { + compatible = "mediatek,mt8365-infracfg","syscon";
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +6
-0+ reg = <0 0x10001000 0 0x1000>; + #clock-cells = <1>; + }; + + pericfg: syscon@10003000 { + compatible = "mediatek,mt8365-pericfg","syscon";
arch/arm64/boot/dts/mediatek/mt8365.dtsi line 235
Quoted 5 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +5
-0+ reg = <0 0x10003000 0 0x1000>; + #clock-cells = <1>; + }; + + syscfg_pctl: syscfg-pctl@10005000 {This is I guess also syscon, like other nodes?
arch/arm64/boot/dts/mediatek/mt8365.dtsi
Quoted 1 line
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ compatible = "syscon";You need specific compatible. Please run
make dtbs_checkand fix the
errors.arch/arm64/boot/dts/mediatek/mt8365.dtsi line 241
Quoted 5 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +5
-0+ reg = <0 0x10005000 0 0x1000>; + }; + + scpsys: syscon@10006000 { + compatible = "syscon", "simple-mfd";You need specific compatible.
arch/arm64/boot/dts/mediatek/mt8365.dtsi
Quoted 2 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +2
-0+ reg = <0 0x10006000 0 0x1000>; + #power-domain-cells = <1>;This is definitely wrong now. It's not a simple-mfd device, so please do
not use that property.arch/arm64/boot/dts/mediatek/mt8365.dtsi line 252
Quoted 10 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +4
-0+ + /* System Power Manager */ + spm: power-controller { + compatible = "mediatek,mt8365-power-controller";
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +5
-0+ #address-cells = <1>; + #size-cells = <0>; + #power-domain-cells = <1>; + + /* power domains of the SoC */The comment suggests you will later add here power domains not for the
SoC. If that's not true, just skip the comment.Quoted 161 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +3
-0+ power-domain@MT8365_POWER_DOMAIN_MM { + reg = <MT8365_POWER_DOMAIN_MM>; + clocks = <&topckgen
CLK_TOP_MM_SEL>,arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ <&mmsys
CLK_MM_MM_SMI_COMMON>,arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ <&mmsys
CLK_MM_MM_SMI_COMM0>,arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ <&mmsys
CLK_MM_MM_SMI_COMM1>,arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ <&mmsys
CLK_MM_MM_SMI_LARB0>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ clock-names = "mm", "mm-0","mm-1",
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +3
-0+ "mm-2", "mm-3"; + #power-domain-cells = <0>; + mediatek,infracfg =<&infracfg>;
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ mediatek,infracfg_nao =<
&infracfg_nao>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +4
-0+ #address-cells = <1>; + #size-cells = <0>; + + power-domain@MT8365_POWER_DOMAI
N_CAM{arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ reg =<
MT8365_POWER_DOMAIN_CAM>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ clocks = <&camsys
CLK_CAM_LARB2>,arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ <&camsys
CLK_CAM_SENIF>,arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ <&camsys
CLK_CAMSV0>,arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ <&camsys
CLK_CAMSV1>,arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ <&camsys
CLK_CAM_FDVT>,arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ <&camsys
CLK_CAM_WPE>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ clock-names = "cam-0","cam-1",
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ "cam-2","cam-3",
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ "cam-4","cam-5";
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ #power-domain-cells =<0>;
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ mediatek,infracfg =<&infracfg>;
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ mediatek,smi =<
&smi_common>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +3
-0+ }; + + power-domain@MT8365_POWER_DOMAI
N_VDEC{arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ reg =<
MT8365_POWER_DOMAIN_VDEC>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ #power-domain-cells =<0>;
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ mediatek,smi =<
&smi_common>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +3
-0+ }; + + power-domain@MT8365_POWER_DOMAI
N_VENC{arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ reg =<
MT8365_POWER_DOMAIN_VENC>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ #power-domain-cells =<0>;
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ mediatek,smi =<
&smi_common>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +3
-0+ }; + + power-domain@MT8365_POWER_DOMAI
N_APU{arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ reg =<
MT8365_POWER_DOMAIN_APU>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ clocks = <&infracfg
CLK_IFR_APU_AXI>,arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ <&apu
CLK_APU_IPU_CK>,arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ <&apu
CLK_APU_AXI>,arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ <&apu
CLK_APU_JTAG>,arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ <&apu
CLK_APU_IF_CK>,arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ <&apu
CLK_APU_EDMA>,arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ <&apu
CLK_APU_AHB>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ clock-names = "apu","apu-0",
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ "apu-1","apu-2",
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ "apu-3","apu-4",
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +2
-0+ "apu-5"; + #power-domain-cells =<0>;
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ mediatek,infracfg =<&infracfg>;
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ mediatek,smi =<
&smi_common>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +5
-0+ }; + }; + + power-domain@MT8365_POWER_DOMAIN_CONN { + reg =<
MT8365_POWER_DOMAIN_CONN>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ clocks = <&topckgen
CLK_TOP_CONN_32K>,arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ <&topckgen
CLK_TOP_CONN_26M>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +3
-0+ clock-names = "conn", "conn1"; + #power-domain-cells = <0>; + mediatek,infracfg =<&infracfg>;
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +4
-0+ }; + + power-domain@MT8365_POWER_DOMAIN_MFG { + reg =<
MT8365_POWER_DOMAIN_MFG>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ clocks = <&topckgen
CLK_TOP_MFG_SEL>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +3
-0+ clock-names = "mfg"; + #power-domain-cells = <0>; + mediatek,infracfg =<&infracfg>;
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +3
-0+ }; + + power-domain@MT8365_POWER_DOMAIN_AUDIO{
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ reg =<
MT8365_POWER_DOMAIN_AUDIO>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ clocks = <&topckgen
CLK_TOP_AUD_INTBUS_SEL>,arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ <&infracfg
CLK_IFR_AUDIO>,arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ <&infracfg
CLK_IFR_AUD_26M_BK>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ clock-names = "audio","audio1", "audio2";
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +2
-0+ #power-domain-cells = <0>; + mediatek,infracfg =<&infracfg>;
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +4
-0+ }; + + power-domain@MT8365_POWER_DOMAIN_DSP { + reg =<
MT8365_POWER_DOMAIN_DSP>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ clocks = <&topckgen
CLK_TOP_DSP_SEL>,arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ <&topckgen
CLK_TOP_DSP_26M>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +3
-0+ clock-names = "dsp", "dsp1"; + #power-domain-cells = <0>; + mediatek,infracfg =<&infracfg>;
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +2
-0+ }; + };arch/arm64/boot/dts/mediatek/mt8365.dtsi line 360
Quoted 10 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +10
-0+ }; + + watchdog: watchdog@10007000 { + compatible = "mediatek,mt8365-wdt", + "mediatek,mt6589-wdt"; + reg = <0 0x10007000 0 0x100>; + #reset-cells = <1>; + }; + + gpt: apxgpt@10008000 {Generic node names, so "timer"
Quoted 30 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +22
-0+ compatible = "mediatek,mt8365-timer", + "mediatek,mt6577-timer"; + reg = <0 0x10008000 0 0x1000>; + interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_LOW>; + clocks = <&topckgen CLK_TOP_SYS_26M_D2>; + clock-names = "clk13m"; + }; + + pio: pinctrl@1000b000 { + compatible = "mediatek,mt8365-pinctrl"; + reg = <0 0x1000b000 0 0x1000>; + mediatek,pctl-regmap = <&syscfg_pctl>; + pins-are-numbered; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>; + }; + + apmixedsys: syscon@1000c000 { + compatible = "mediatek,mt8365-apmixedsys","syscon";
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +7
-0+ reg = <0 0x1000c000 0 0x1000>; + #clock-cells = <1>; + }; + + pwrap: pwrap@1000d000 { + compatible = "mediatek,mt8365-pwrap"; + reg = <0 0x1000d000 0 0x1000>;arch/arm64/boot/dts/mediatek/mt8365.dtsi line 399
Quoted 10 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +10
-0+ reg-names = "pwrap"; + interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&infracfg CLK_IFR_PWRAP_SPI>, + <&infracfg CLK_IFR_PMIC_AP>, + <&infracfg CLK_IFR_PWRAP_SYS>, + <&infracfg CLK_IFR_PWRAP_TMR>; + clock-names = "spi", "wrap", "sys", "tmr"; + }; + + keypad: kp@10010000 {s/kp/keypad/
Quoted 13 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +4
-0+ compatible = "mediatek,mt6779-keypad"; + reg = <0 0x10010000 0 0x1000>; + wakeup-source; + interrupts = <GIC_SPI 124
IRQ_TYPE_EDGE_FALLING>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +7
-0+ clocks = <&clk26m>; + clock-names = "kpd"; + status = "disabled"; + }; + + mcucfg: syscon@10200000 { + compatible = "mediatek,mt8365-mcucfg","syscon";
arch/arm64/boot/dts/mediatek/mt8365.dtsi line 415
Quoted 5 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +5
-0+ reg = <0 0x10200000 0 0x2000>; + #clock-cells = <1>; + }; + + sysirq: intpol-controller@10200a80 {interrupt-controller
Quoted 14 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +13
-0+ compatible = "mediatek,mt8365-sysirq", + "mediatek,mt6577-sysirq"; + interrupt-controller; + #interrupt-cells = <3>; + interrupt-parent = <&gic>; + reg = <0 0x10200a80 0 0x20>; + }; + + iommu: iommu@10205000 { + compatible = "mediatek,mt8365-m4u"; + reg = <0 0x10205000 0 0x1000>; + interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_LOW>; + mediatek,larbs = <&larb0>, <&larb1>, <&larb2>,<&larb3>;
arch/arm64/boot/dts/mediatek/mt8365.dtsi line 432
Quoted 4 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +4
-0+ #iommu-cells = <1>; + }; + + infracfg_nao: infracfg-nao@1020e000 {Other nodes are named syscon
arch/arm64/boot/dts/mediatek/mt8365.dtsi
Quoted 1 line
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ compatible = "syscon";No, syscon cannot be alone.
Quoted 40 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +40
-0+ reg = <0 0x1020e000 0 0x1000>; + }; + + rng: rng@1020f000 { + compatible = "mediatek,mt8365-rng", + "mediatek,mt7623-rng"; + reg = <0 0x1020f000 0 0x100>; + clocks = <&infracfg CLK_IFR_TRNG>; + clock-names = "rng"; + }; + + apdma: dma-controller@11000280 { + compatible = "mediatek,mt8365-uart-dma", + "mediatek,mt6577-uart-dma"; + reg = <0 0x11000280 0 0x80>, + <0 0x11000300 0 0x80>, + <0 0x11000380 0 0x80>, + <0 0x11000400 0 0x80>, + <0 0x11000580 0 0x80>, + <0 0x11000600 0 0x80>; + interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 46 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 47 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 48 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 51 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 52 IRQ_TYPE_LEVEL_LOW>; + dma-requests = <6>; + clocks = <&infracfg CLK_IFR_AP_DMA>; + clock-names = "apdma"; + #dma-cells = <1>; + }; + + auxadc: adc@11001000 { + compatible = "mediatek,mt8365-auxadc", + "mediatek,mt8173-auxadc"; + reg = <0 0x11001000 0 0x1000>; + clocks = <&infracfg CLK_IFR_AUXADC>; + clock-names = "main"; + #io-channel-cells = <1>; + };arch/arm64/boot/dts/mediatek/mt8365.dtsi line 483
Quoted 10 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +10
-0+ + uart0: serial@11002000 { + compatible = "mediatek,mt8365-uart", + "mediatek,mt6577-uart"; + reg = <0 0x11002000 0 0x1000>; + interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_LOW>; + clocks = <&clk26m>, <&infracfg CLK_IFR_UART0>; + clock-names = "baud", "bus"; + dmas = <&apdma 0 + &apdma 1>;You need to split these into two phandles.
arch/arm64/boot/dts/mediatek/mt8365.dtsi line 496
Quoted 13 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +13
-0+ dma-names = "tx", "rx"; + status = "disabled"; + }; + + uart1: serial@11003000 { + compatible = "mediatek,mt8365-uart", + "mediatek,mt6577-uart"; + reg = <0 0x11003000 0 0x1000>; + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_LOW>; + clocks = <&clk26m>, <&infracfg CLK_IFR_UART1>; + clock-names = "baud", "bus"; + dmas = <&apdma 2 + &apdma 3>;Ditto.
Quoted 72 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +28
-0+ dma-names = "tx", "rx"; + status = "disabled"; + }; + + uart2: serial@11004000 { + compatible = "mediatek,mt8365-uart", + "mediatek,mt6577-uart"; + reg = <0 0x11004000 0 0x1000>; + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_LOW>; + clocks = <&clk26m>, <&infracfg CLK_IFR_UART2>; + clock-names = "baud", "bus"; + dmas = <&apdma 4 + &apdma 5>; + dma-names = "tx", "rx"; + status = "disabled"; + }; + + pwm: pwm@11006000 { + compatible = "mediatek,mt8365-pwm"; + reg = <0 0x11006000 0 0x1000>; + #pwm-cells = <2>; + interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_LOW>; + clocks = <&infracfg CLK_IFR_PWM_HCLK>, + <&infracfg CLK_IFR_PWM>, + <&infracfg CLK_IFR_PWM1>, + <&infracfg CLK_IFR_PWM2>, + <&infracfg CLK_IFR_PWM3>; + clock-names = "top", "main", "pwm1", "pwm2","pwm3";
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +43
-0+ }; + + i2c0: i2c@11007000 { + compatible = "mediatek,mt8365-i2c", + "mediatek,mt8168-i2c"; + reg = <0 0x11007000 0 0xa0>, + <0 0x11000080 0 0x80>; + interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_LOW>; + clock-div = <1>; + clocks = <&infracfg CLK_IFR_I2C0_AXI>, + <&infracfg CLK_IFR_AP_DMA>; + clock-names = "main", "dma"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c1: i2c@11008000 { + compatible = "mediatek,mt8365-i2c", + "mediatek,mt8168-i2c"; + reg = <0 0x11008000 0 0xa0>, + <0 0x11000100 0 0x80>; + interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_LOW>; + clock-div = <1>; + clocks = <&infracfg CLK_IFR_I2C1_AXI>, + <&infracfg CLK_IFR_AP_DMA>; + clock-names = "main", "dma"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c2: i2c@11009000 { + compatible = "mediatek,mt8365-i2c", + "mediatek,mt8168-i2c"; + reg = <0 0x11009000 0 0xa0>, + <0 0x11000180 0 0x80>; + interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_LOW>; + clock-div = <1>; + clocks = <&infracfg CLK_IFR_I2C2_AXI>, + <&infracfg CLK_IFR_AP_DMA>; + clock-names = "main", "dma"; + #address-cells = <1>;arch/arm64/boot/dts/mediatek/mt8365.dtsi line 577
Quoted 10 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +10
-0+ #size-cells = <0>; + status = "disabled"; + }; + + spi: spi@1100a000 { + compatible = "mediatek,mt8365-spi", + "mediatek,mt7622-spi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0 0x1100a000 0 0x100>;Reg goes after compatible.
Quoted 14 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +5
-0+ interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_LOW>; + clocks = <&topckgen CLK_TOP_UNIVPLL2_D4>, + <&topckgen CLK_TOP_SPI_SEL>, + <&infracfg CLK_IFR_SPI0>; + clock-names = "parent-clk", "sel-clk", "spi-clk";
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +8
-0+ status = "disabled"; + }; + + thermal: thermal@1100b000 { + compatible = "mediatek,mt8365-thermal"; + reg = <0 0x1100b000 0 0x1000>; + interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_LOW>; + clocks = <&infracfg CLK_IFR_THERM>,arch/arm64/boot/dts/mediatek/mt8365.dtsi line 600
Quoted 10 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +10
-0+ <&infracfg CLK_IFR_AUXADC>; + clock-names = "therm", "auxadc"; + mediatek,auxadc = <&auxadc>; + mediatek,apmixedsys = <&apmixedsys>; + nvmem-cells = <&thermal_calibration>; + nvmem-cell-names = "calibration-data"; + #thermal-sensor-cells = <1>; + }; + + disp_pwm: disp-pwm@1100e000 {Generic node names, so "pwm"
Quoted 123 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +28
-0+ compatible = "mediatek,mt8365-disp-pwm", + "mediatek,mt8183-disp-pwm"; + reg = <0 0x1100e000 0 0x1000>; + #pwm-cells = <2>; + clocks = <&topckgen CLK_TOP_DISP_PWM_SEL>, + <&infracfg CLK_IFR_DISP_PWM>; + clock-names = "main", "mm"; + power-domains = <&spm MT8365_POWER_DOMAIN_MM>; + status = "disabled"; + }; + + i2c3: i2c@1100f000 { + compatible = "mediatek,mt8365-i2c", + "mediatek,mt8168-i2c"; + reg = <0 0x1100f000 0 0xa0>, + <0 0x11000200 0 0x80>; + interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_LOW>; + clock-div = <1>; + clocks = <&infracfg CLK_IFR_I2C3_AXI>, + <&infracfg CLK_IFR_AP_DMA>; + clock-names = "main", "dma"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + ssusb: usb@11201000 { + compatible = "mediatek,mt8365-mtu3","mediatek,mtu3";
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +23
-0+ reg = <0 0x11201000 0 0x2e00>, + <0 0x11203e00 0 0x0100>; + reg-names = "mac", "ippc"; + interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_LOW>; + phys = <&u2port0 PHY_TYPE_USB2>, + <&u2port1 PHY_TYPE_USB2>; + clocks = <&topckgen CLK_TOP_SSUSB_TOP_CK_EN>, + <&infracfg CLK_IFR_SSUSB_REF>, + <&infracfg CLK_IFR_SSUSB_SYS>, + <&infracfg CLK_IFR_ICUSB>; + clock-names = "sys_ck", "ref_ck", "mcu_ck", + "dma_ck"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + status = "disabled"; + + usb_host: usb@11200000 { + compatible = "mediatek,mt8365-xhci", + "mediatek,mtk-xhci"; + reg = <0 0x11200000 0 0x1000>; + reg-names = "mac"; + interrupts = <GIC_SPI 67
IRQ_TYPE_LEVEL_LOW>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ clocks = <&topckgen
CLK_TOP_SSUSB_TOP_CK_EN>,arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +4
-0+ <&infracfg CLK_IFR_SSUSB_REF>, + <&infracfg CLK_IFR_SSUSB_SYS>, + <&infracfg CLK_IFR_ICUSB>, + <&infracfg
CLK_IFR_SSUSB_XHCI>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ clock-names = "sys_ck", "ref_ck","
mcu_ck",arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +7
-0+ "dma_ck", "xhci_ck"; + status = "disabled"; + }; + }; + + mmc0: mmc@11230000 { + compatible = "mediatek,mt8365-mmc","mediatek,mt8183-mmc";
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +12
-0+ reg = <0 0x11230000 0 0x1000>, + <0 0x11cd0000 0 0x1000>; + interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_LOW>; + clocks = <&topckgen CLK_TOP_MSDC50_0_SEL>, + <&infracfg CLK_IFR_MSDC0_HCLK>, + <&infracfg CLK_IFR_MSDC0_SRC>; + clock-names = "source", "hclk", "source_cg"; + status = "disabled"; + }; + + mmc1: mmc@11240000 { + compatible = "mediatek,mt8365-mmc","mediatek,mt8183-mmc";
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +35
-0+ reg = <0 0x11240000 0 0x1000>, + <0 0x11c90000 0 0x1000>; + interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_LOW>; + clocks = <&topckgen CLK_TOP_MSDC30_1_SEL>, + <&infracfg CLK_IFR_MSDC1_HCLK>, + <&infracfg CLK_IFR_MSDC1_SRC>; + clock-names = "source", "hclk", "source_cg"; + status = "disabled"; + }; + + ethernet: ethernet@112a0000 { + compatible = "mediatek,mt8365-eth"; + reg = <0 0x112a0000 0 0x1000>; + mediatek,pericfg = <&infracfg>; + interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&topckgen CLK_TOP_ETH_SEL>, + <&infracfg CLK_IFR_NIC_AXI>, + <&infracfg CLK_IFR_NIC_SLV_AXI>; + clock-names = "core", "reg", "trans"; + status = "disabled"; + }; + + mipi_tx0: dsi-phy@11c00000 { + compatible = "mediatek,mt8365-mipi-tx", + "mediatek,mt8183-mipi-tx"; + reg = <0 0x11c00000 0 0x800>; + clocks = <&clk26m>; + clock-names = "ref_clk"; + #clock-cells = <0>; + #phy-cells = <0>; + clock-output-names = "mipi_tx0_pll"; + }; + + efuse: efuse@11c50000 { + compatible = "mediatek,mt8365-efuse","mediatek,efuse";
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +4
-0+ reg = <0 0x11c50000 0 0x1000>; + #address-cells = <1>; + #size-cells = <1>; +
Quoted 8 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi line 721
Quoted 6 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +6
-0+ thermal_calibration: calib@180 { + reg = <0x180 0xc>; + }; + }; + + u3phy: t-phy@11cc0000 {s/t-phy/phy/
can't use phy here, if will cause dt-binding check fail.
Quoted 93 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi line 725
Quoted 5 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +4
-0+ compatible = "mediatek,mt8365-tphy", + "mediatek,generic-tphy-v2"; + #address-cells = <2>; + #phy-cells = <1>;address-cells, then size, then phy
arch/arm64/boot/dts/mediatek/mt8365.dtsi line 728
Quoted 3 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +3
-0+ #size-cells = <2>; + ranges; + status = "okay";No need for status ok.
arch/arm64/boot/dts/mediatek/mt8365.dtsi line 736
Quoted 10 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +4
-0+ + u2port0: usb-phy@11cc0000 { + reg = <0 0x11cc0000 0 0x400>; + clocks = <&topckgen
CLK_TOP_SSUSB_PHY_CK_EN>,arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ <&topckgen
CLK_TOP_USB20_48M_EN>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +3
-0+ clock-names = "ref", "da_ref"; + #phy-cells = <1>; + status = "okay";Ditto
Quoted 25 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +5
-0+ }; + + u2port1: usb-phy@11cc1000 { + reg = <0 0x11cc1000 0 0x400>; + clocks = <&topckgen
CLK_TOP_SSUSB_PHY_CK_EN>,arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ <&topckgen
CLK_TOP_USB20_48M_EN>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +8
-0+ clock-names = "ref", "da_ref"; + #phy-cells = <1>; + status = "okay"; + }; + }; + + mfgcfg: syscon@13000000 { + compatible = "mediatek,mt8365-mfgcfg","syscon";
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +8
-0+ reg = <0 0x13000000 0 0x1000>; + #clock-cells = <1>; + }; + + mmsys: syscon@14000000 { + compatible = "mediatek,mt8365-mmsys", "syscon"; + reg = <0 0x14000000 0 0x1000>; + #clock-cells = <1>;arch/arm64/boot/dts/mediatek/mt8365.dtsi line 768
Quoted 10 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +10
-0+ }; + + mutex: mutex@14001000 { + compatible = "mediatek,mt8365-disp-mutex"; + reg = <0 0x14001000 0 0x1000>; + interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&spm MT8365_POWER_DOMAIN_MM>; + }; + + smi_common: smi@14002000 {s/smi/memory-controller/ in node name?
arch/arm64/boot/dts/mediatek/mt8365.dtsi line 780
Quoted 12 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +12
-0+ compatible = "mediatek,mt8365-smi-common", + "mediatek,mt8186-smi-common"; + reg = <0 0x14002000 0 0x1000>; + clocks = <&mmsys CLK_MM_MM_SMI_COMMON>, + <&mmsys CLK_MM_MM_SMI_COMMON>, + <&mmsys CLK_MM_MM_SMI_COMM0>, + <&mmsys CLK_MM_MM_SMI_COMM1>; + clock-names = "apb", "smi", "gals0", "gals1"; + power-domains = <&spm MT8365_POWER_DOMAIN_MM>; + }; + + larb0: larb@14003000 {The same?
arch/arm64/boot/dts/mediatek/mt8365.dtsi line 788
Quoted 8 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +8
-0+ compatible = "mediatek,mt8365-smi-larb", + "mediatek,mt8186-smi-larb"; + reg = <0 0x14003000 0 0x1000>; + mediatek,smi = <&smi_common>; + clocks = <&mmsys CLK_MM_MM_SMI_LARB0>, + <&mmsys CLK_MM_MM_SMI_LARB0>; + clock-names = "apb", "smi"; + power-domains = <&spm MT8365_POWER_DOMAIN_MM>;Best regards,
Krzysztof
Chunfeng Yun
maintainerRe: [PATCH 16/17] arm64: dts: mediatek: add mt8365 device-tree
In reply to Krzysztof KozlowskiQuoted 12 lines · Krzysztof Kozlowski
Quoted 11 lines · Fabien Parent
Add device-tree for the MT8365 SoC. More information can be found about that SoC at the following address:
https://www.mediatek.com/products/aiot/i350-mt8365Signed-off-by Fabien Parent <[email protected]>--- arch/arm64/boot/dts/mediatek/mt8365.dtsi | 1047 ++++++++++++++++++++++ 1 file changed, 1047 insertions(+) create mode 100644 arch/arm64/boot/dts/mediatek/mt8365.dtsi
Quoted 10 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi line 3
Quoted 10 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +3
-0@@ -0,0 +1,1047 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Copyright (c) 2018 MediaTek Inc.
2022?
Quoted 858 lines
Quoted 166 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +166
-0+ */ + +#include <dt-bindings/clock/mediatek,mt8365-clk.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/phy/phy.h> +#include <dt-bindings/power/mt8365-power.h> +#include <dt-bindings/memory/mt8365-larb-port.h> +#include <dt-bindings/thermal/thermal.h> + +/ { + compatible = "mediatek,mt8365"; + interrupt-parent = <&sysirq>; + #address-cells = <2>; + #size-cells = <2>; + + aliases { + ovl0 = &ovl0; + rdma0 = &rdma0; + rdma1 = &rdma1; + color0 = &color0; + ccorr0 = &ccorr0; + aal0 = &aal0; + gamma0 = &gamma0; + dither0 = &dither0; + dsi0 = &dsi0; + dpi0 = &dpi0; + }; + + cpus: cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu-map { + cluster0: cluster0 { + core0 { + cpu = <&cpu0>; + }; + core1 { + cpu = <&cpu1>; + }; + core2 { + cpu = <&cpu2>; + }; + core3 { + cpu = <&cpu3>; + }; + }; + }; + + cpu0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x0>; + clock-frequency = <1600000000>; + clocks = <&mcucfg CLK_MCU_BUS_SEL>, + <&apmixedsys CLK_APMIXED_MAINPLL>; + clock-names = "cpu", "intermediate"; + operating-points-v2 = <&cluster0_opp>; + #cooling-cells = <2>; + enable-method = "psci"; + }; + + cpu1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x1>; + clock-frequency = <1600000000>; + clocks = <&mcucfg CLK_MCU_BUS_SEL>, + <&apmixedsys CLK_APMIXED_MAINPLL>; + clock-names = "cpu", "intermediate", "armpll"; + operating-points-v2 = <&cluster0_opp>; + #cooling-cells = <2>; + enable-method = "psci"; + }; + + cpu2: cpu@2 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x2>; + clock-frequency = <1600000000>; + clocks = <&mcucfg CLK_MCU_BUS_SEL>, + <&apmixedsys CLK_APMIXED_MAINPLL>; + clock-names = "cpu", "intermediate", "armpll"; + operating-points-v2 = <&cluster0_opp>; + #cooling-cells = <2>; + enable-method = "psci"; + }; + + cpu3: cpu@3 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x3>; + clock-frequency = <1600000000>; + clocks = <&mcucfg CLK_MCU_BUS_SEL>, + <&apmixedsys CLK_APMIXED_MAINPLL>; + clock-names = "cpu", "intermediate", "armpll"; + operating-points-v2 = <&cluster0_opp>; + #cooling-cells = <2>; + enable-method = "psci"; + }; + }; + + cluster0_opp: opp-table-0 { + compatible = "operating-points-v2"; + opp-shared; + opp-850000000 { + opp-hz = /bits/ 64 <850000000>; + opp-microvolt = <650000>; + }; + opp-918000000 { + opp-hz = /bits/ 64 <918000000>; + opp-microvolt = <668750>; + }; + opp-987000000 { + opp-hz = /bits/ 64 <987000000>; + opp-microvolt = <687500>; + }; + opp-1056000000 { + opp-hz = /bits/ 64 <1056000000>; + opp-microvolt = <706250>; + }; + opp-1125000000 { + opp-hz = /bits/ 64 <1125000000>; + opp-microvolt = <725000>; + }; + opp-1216000000 { + opp-hz = /bits/ 64 <1216000000>; + opp-microvolt = <750000>; + }; + opp-1308000000 { + opp-hz = /bits/ 64 <1308000000>; + opp-microvolt = <775000>; + }; + opp-1400000000 { + opp-hz = /bits/ 64 <1400000000>; + opp-microvolt = <800000>; + }; + opp-1466000000 { + opp-hz = /bits/ 64 <1466000000>; + opp-microvolt = <825000>; + }; + opp-1533000000 { + opp-hz = /bits/ 64 <1533000000>; + opp-microvolt = <850000>; + }; + opp-1633000000 { + opp-hz = /bits/ 64 <1633000000>; + opp-microvolt = <887500>; + }; + opp-1700000000 { + opp-hz = /bits/ 64 <1700000000>; + opp-microvolt = <912500>; + }; + opp-1767000000 { + opp-hz = /bits/ 64 <1767000000>; + opp-microvolt = <937500>; + }; + opp-1834000000 { + opp-hz = /bits/ 64 <1834000000>; + opp-microvolt = <962500>; + }; + opp-1917000000 { + opp-hz = /bits/ 64 <1917000000>; + opp-microvolt = <993750>; + };arch/arm64/boot/dts/mediatek/mt8365.dtsi line 179
Quoted 10 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +10
-0+ opp-2001000000 { + opp-hz = /bits/ 64 <2001000000>; + opp-microvolt = <1025000>; + }; + }; + + clk26m: oscillator { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <26000000>;This does not look like property of a SoC. Are you sure MT8365 SoC has
this clock (not the board)?Quoted 19 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +19
-0+ clock-output-names = "clk26m"; + }; + + psci { + compatible = "arm,psci-1.0"; + method = "smc"; + }; + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + /* 128 KiB reserved for ARM Trusted Firmware (BL31) */ + bl31_secmon_reserved: secmon@43000000 { + no-map; + reg = <0 0x43000000 0 0x20000>; + }; + };arch/arm64/boot/dts/mediatek/mt8365.dtsi line 208
Quoted 10 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +10
-0+ + soc { + #address-cells = <2>; + #size-cells = <2>; + compatible = "simple-bus"; + ranges; + + gic: interrupt-controller@c000000 { + compatible = "arm,gic-v3"; + #interrupt-cells = <4>;Why do you have four cells here (and passing 0 as interrupt)?
Quoted 25 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +10
-0+ interrupt-parent = <&gic>; + interrupt-controller; + reg = <0 0x0c000000 0 0x80000>, + <0 0x0c080000 0 0x80000>; + + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH 0>; + }; + + topckgen: syscon@10000000 { + compatible = "mediatek,mt8365-topckgen","syscon";
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +6
-0+ reg = <0 0x10000000 0 0x1000>; + #clock-cells = <1>; + }; + + infracfg: syscon@10001000 { + compatible = "mediatek,mt8365-infracfg","syscon";
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +6
-0+ reg = <0 0x10001000 0 0x1000>; + #clock-cells = <1>; + }; + + pericfg: syscon@10003000 { + compatible = "mediatek,mt8365-pericfg","syscon";
arch/arm64/boot/dts/mediatek/mt8365.dtsi line 235
Quoted 5 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +5
-0+ reg = <0 0x10003000 0 0x1000>; + #clock-cells = <1>; + }; + + syscfg_pctl: syscfg-pctl@10005000 {This is I guess also syscon, like other nodes?
arch/arm64/boot/dts/mediatek/mt8365.dtsi
Quoted 1 line
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ compatible = "syscon";You need specific compatible. Please run
make dtbs_checkand fix the
errors.arch/arm64/boot/dts/mediatek/mt8365.dtsi line 241
Quoted 5 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +5
-0+ reg = <0 0x10005000 0 0x1000>; + }; + + scpsys: syscon@10006000 { + compatible = "syscon", "simple-mfd";You need specific compatible.
arch/arm64/boot/dts/mediatek/mt8365.dtsi
Quoted 2 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +2
-0+ reg = <0 0x10006000 0 0x1000>; + #power-domain-cells = <1>;This is definitely wrong now. It's not a simple-mfd device, so please do
not use that property.arch/arm64/boot/dts/mediatek/mt8365.dtsi line 252
Quoted 10 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +4
-0+ + /* System Power Manager */ + spm: power-controller { + compatible = "mediatek,mt8365-power-controller";
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +5
-0+ #address-cells = <1>; + #size-cells = <0>; + #power-domain-cells = <1>; + + /* power domains of the SoC */The comment suggests you will later add here power domains not for the
SoC. If that's not true, just skip the comment.Quoted 161 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +3
-0+ power-domain@MT8365_POWER_DOMAIN_MM { + reg = <MT8365_POWER_DOMAIN_MM>; + clocks = <&topckgen
CLK_TOP_MM_SEL>,arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ <&mmsys
CLK_MM_MM_SMI_COMMON>,arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ <&mmsys
CLK_MM_MM_SMI_COMM0>,arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ <&mmsys
CLK_MM_MM_SMI_COMM1>,arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ <&mmsys
CLK_MM_MM_SMI_LARB0>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ clock-names = "mm", "mm-0","mm-1",
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +3
-0+ "mm-2", "mm-3"; + #power-domain-cells = <0>; + mediatek,infracfg =<&infracfg>;
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ mediatek,infracfg_nao =<
&infracfg_nao>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +4
-0+ #address-cells = <1>; + #size-cells = <0>; + + power-domain@MT8365_POWER_DOMAI
N_CAM{arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ reg =<
MT8365_POWER_DOMAIN_CAM>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ clocks = <&camsys
CLK_CAM_LARB2>,arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ <&camsys
CLK_CAM_SENIF>,arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ <&camsys
CLK_CAMSV0>,arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ <&camsys
CLK_CAMSV1>,arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ <&camsys
CLK_CAM_FDVT>,arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ <&camsys
CLK_CAM_WPE>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ clock-names = "cam-0","cam-1",
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ "cam-2","cam-3",
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ "cam-4","cam-5";
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ #power-domain-cells =<0>;
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ mediatek,infracfg =<&infracfg>;
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ mediatek,smi =<
&smi_common>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +3
-0+ }; + + power-domain@MT8365_POWER_DOMAI
N_VDEC{arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ reg =<
MT8365_POWER_DOMAIN_VDEC>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ #power-domain-cells =<0>;
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ mediatek,smi =<
&smi_common>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +3
-0+ }; + + power-domain@MT8365_POWER_DOMAI
N_VENC{arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ reg =<
MT8365_POWER_DOMAIN_VENC>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ #power-domain-cells =<0>;
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ mediatek,smi =<
&smi_common>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +3
-0+ }; + + power-domain@MT8365_POWER_DOMAI
N_APU{arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ reg =<
MT8365_POWER_DOMAIN_APU>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ clocks = <&infracfg
CLK_IFR_APU_AXI>,arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ <&apu
CLK_APU_IPU_CK>,arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ <&apu
CLK_APU_AXI>,arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ <&apu
CLK_APU_JTAG>,arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ <&apu
CLK_APU_IF_CK>,arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ <&apu
CLK_APU_EDMA>,arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ <&apu
CLK_APU_AHB>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ clock-names = "apu","apu-0",
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ "apu-1","apu-2",
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ "apu-3","apu-4",
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +2
-0+ "apu-5"; + #power-domain-cells =<0>;
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ mediatek,infracfg =<&infracfg>;
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ mediatek,smi =<
&smi_common>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +5
-0+ }; + }; + + power-domain@MT8365_POWER_DOMAIN_CONN { + reg =<
MT8365_POWER_DOMAIN_CONN>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ clocks = <&topckgen
CLK_TOP_CONN_32K>,arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ <&topckgen
CLK_TOP_CONN_26M>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +3
-0+ clock-names = "conn", "conn1"; + #power-domain-cells = <0>; + mediatek,infracfg =<&infracfg>;
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +4
-0+ }; + + power-domain@MT8365_POWER_DOMAIN_MFG { + reg =<
MT8365_POWER_DOMAIN_MFG>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ clocks = <&topckgen
CLK_TOP_MFG_SEL>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +3
-0+ clock-names = "mfg"; + #power-domain-cells = <0>; + mediatek,infracfg =<&infracfg>;
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +3
-0+ }; + + power-domain@MT8365_POWER_DOMAIN_AUDIO{
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ reg =<
MT8365_POWER_DOMAIN_AUDIO>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ clocks = <&topckgen
CLK_TOP_AUD_INTBUS_SEL>,arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ <&infracfg
CLK_IFR_AUDIO>,arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ <&infracfg
CLK_IFR_AUD_26M_BK>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ clock-names = "audio","audio1", "audio2";
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +2
-0+ #power-domain-cells = <0>; + mediatek,infracfg =<&infracfg>;
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +4
-0+ }; + + power-domain@MT8365_POWER_DOMAIN_DSP { + reg =<
MT8365_POWER_DOMAIN_DSP>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ clocks = <&topckgen
CLK_TOP_DSP_SEL>,arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ <&topckgen
CLK_TOP_DSP_26M>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +3
-0+ clock-names = "dsp", "dsp1"; + #power-domain-cells = <0>; + mediatek,infracfg =<&infracfg>;
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +2
-0+ }; + };arch/arm64/boot/dts/mediatek/mt8365.dtsi line 360
Quoted 10 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +10
-0+ }; + + watchdog: watchdog@10007000 { + compatible = "mediatek,mt8365-wdt", + "mediatek,mt6589-wdt"; + reg = <0 0x10007000 0 0x100>; + #reset-cells = <1>; + }; + + gpt: apxgpt@10008000 {Generic node names, so "timer"
Quoted 30 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +22
-0+ compatible = "mediatek,mt8365-timer", + "mediatek,mt6577-timer"; + reg = <0 0x10008000 0 0x1000>; + interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_LOW>; + clocks = <&topckgen CLK_TOP_SYS_26M_D2>; + clock-names = "clk13m"; + }; + + pio: pinctrl@1000b000 { + compatible = "mediatek,mt8365-pinctrl"; + reg = <0 0x1000b000 0 0x1000>; + mediatek,pctl-regmap = <&syscfg_pctl>; + pins-are-numbered; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>; + }; + + apmixedsys: syscon@1000c000 { + compatible = "mediatek,mt8365-apmixedsys","syscon";
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +7
-0+ reg = <0 0x1000c000 0 0x1000>; + #clock-cells = <1>; + }; + + pwrap: pwrap@1000d000 { + compatible = "mediatek,mt8365-pwrap"; + reg = <0 0x1000d000 0 0x1000>;arch/arm64/boot/dts/mediatek/mt8365.dtsi line 399
Quoted 10 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +10
-0+ reg-names = "pwrap"; + interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&infracfg CLK_IFR_PWRAP_SPI>, + <&infracfg CLK_IFR_PMIC_AP>, + <&infracfg CLK_IFR_PWRAP_SYS>, + <&infracfg CLK_IFR_PWRAP_TMR>; + clock-names = "spi", "wrap", "sys", "tmr"; + }; + + keypad: kp@10010000 {s/kp/keypad/
Quoted 13 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +4
-0+ compatible = "mediatek,mt6779-keypad"; + reg = <0 0x10010000 0 0x1000>; + wakeup-source; + interrupts = <GIC_SPI 124
IRQ_TYPE_EDGE_FALLING>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +7
-0+ clocks = <&clk26m>; + clock-names = "kpd"; + status = "disabled"; + }; + + mcucfg: syscon@10200000 { + compatible = "mediatek,mt8365-mcucfg","syscon";
arch/arm64/boot/dts/mediatek/mt8365.dtsi line 415
Quoted 5 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +5
-0+ reg = <0 0x10200000 0 0x2000>; + #clock-cells = <1>; + }; + + sysirq: intpol-controller@10200a80 {interrupt-controller
Quoted 14 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +13
-0+ compatible = "mediatek,mt8365-sysirq", + "mediatek,mt6577-sysirq"; + interrupt-controller; + #interrupt-cells = <3>; + interrupt-parent = <&gic>; + reg = <0 0x10200a80 0 0x20>; + }; + + iommu: iommu@10205000 { + compatible = "mediatek,mt8365-m4u"; + reg = <0 0x10205000 0 0x1000>; + interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_LOW>; + mediatek,larbs = <&larb0>, <&larb1>, <&larb2>,<&larb3>;
arch/arm64/boot/dts/mediatek/mt8365.dtsi line 432
Quoted 4 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +4
-0+ #iommu-cells = <1>; + }; + + infracfg_nao: infracfg-nao@1020e000 {Other nodes are named syscon
arch/arm64/boot/dts/mediatek/mt8365.dtsi
Quoted 1 line
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ compatible = "syscon";No, syscon cannot be alone.
Quoted 40 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +40
-0+ reg = <0 0x1020e000 0 0x1000>; + }; + + rng: rng@1020f000 { + compatible = "mediatek,mt8365-rng", + "mediatek,mt7623-rng"; + reg = <0 0x1020f000 0 0x100>; + clocks = <&infracfg CLK_IFR_TRNG>; + clock-names = "rng"; + }; + + apdma: dma-controller@11000280 { + compatible = "mediatek,mt8365-uart-dma", + "mediatek,mt6577-uart-dma"; + reg = <0 0x11000280 0 0x80>, + <0 0x11000300 0 0x80>, + <0 0x11000380 0 0x80>, + <0 0x11000400 0 0x80>, + <0 0x11000580 0 0x80>, + <0 0x11000600 0 0x80>; + interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 46 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 47 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 48 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 51 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 52 IRQ_TYPE_LEVEL_LOW>; + dma-requests = <6>; + clocks = <&infracfg CLK_IFR_AP_DMA>; + clock-names = "apdma"; + #dma-cells = <1>; + }; + + auxadc: adc@11001000 { + compatible = "mediatek,mt8365-auxadc", + "mediatek,mt8173-auxadc"; + reg = <0 0x11001000 0 0x1000>; + clocks = <&infracfg CLK_IFR_AUXADC>; + clock-names = "main"; + #io-channel-cells = <1>; + };arch/arm64/boot/dts/mediatek/mt8365.dtsi line 483
Quoted 10 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +10
-0+ + uart0: serial@11002000 { + compatible = "mediatek,mt8365-uart", + "mediatek,mt6577-uart"; + reg = <0 0x11002000 0 0x1000>; + interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_LOW>; + clocks = <&clk26m>, <&infracfg CLK_IFR_UART0>; + clock-names = "baud", "bus"; + dmas = <&apdma 0 + &apdma 1>;You need to split these into two phandles.
arch/arm64/boot/dts/mediatek/mt8365.dtsi line 496
Quoted 13 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +13
-0+ dma-names = "tx", "rx"; + status = "disabled"; + }; + + uart1: serial@11003000 { + compatible = "mediatek,mt8365-uart", + "mediatek,mt6577-uart"; + reg = <0 0x11003000 0 0x1000>; + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_LOW>; + clocks = <&clk26m>, <&infracfg CLK_IFR_UART1>; + clock-names = "baud", "bus"; + dmas = <&apdma 2 + &apdma 3>;Ditto.
Quoted 72 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +28
-0+ dma-names = "tx", "rx"; + status = "disabled"; + }; + + uart2: serial@11004000 { + compatible = "mediatek,mt8365-uart", + "mediatek,mt6577-uart"; + reg = <0 0x11004000 0 0x1000>; + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_LOW>; + clocks = <&clk26m>, <&infracfg CLK_IFR_UART2>; + clock-names = "baud", "bus"; + dmas = <&apdma 4 + &apdma 5>; + dma-names = "tx", "rx"; + status = "disabled"; + }; + + pwm: pwm@11006000 { + compatible = "mediatek,mt8365-pwm"; + reg = <0 0x11006000 0 0x1000>; + #pwm-cells = <2>; + interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_LOW>; + clocks = <&infracfg CLK_IFR_PWM_HCLK>, + <&infracfg CLK_IFR_PWM>, + <&infracfg CLK_IFR_PWM1>, + <&infracfg CLK_IFR_PWM2>, + <&infracfg CLK_IFR_PWM3>; + clock-names = "top", "main", "pwm1", "pwm2","pwm3";
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +43
-0+ }; + + i2c0: i2c@11007000 { + compatible = "mediatek,mt8365-i2c", + "mediatek,mt8168-i2c"; + reg = <0 0x11007000 0 0xa0>, + <0 0x11000080 0 0x80>; + interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_LOW>; + clock-div = <1>; + clocks = <&infracfg CLK_IFR_I2C0_AXI>, + <&infracfg CLK_IFR_AP_DMA>; + clock-names = "main", "dma"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c1: i2c@11008000 { + compatible = "mediatek,mt8365-i2c", + "mediatek,mt8168-i2c"; + reg = <0 0x11008000 0 0xa0>, + <0 0x11000100 0 0x80>; + interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_LOW>; + clock-div = <1>; + clocks = <&infracfg CLK_IFR_I2C1_AXI>, + <&infracfg CLK_IFR_AP_DMA>; + clock-names = "main", "dma"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c2: i2c@11009000 { + compatible = "mediatek,mt8365-i2c", + "mediatek,mt8168-i2c"; + reg = <0 0x11009000 0 0xa0>, + <0 0x11000180 0 0x80>; + interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_LOW>; + clock-div = <1>; + clocks = <&infracfg CLK_IFR_I2C2_AXI>, + <&infracfg CLK_IFR_AP_DMA>; + clock-names = "main", "dma"; + #address-cells = <1>;arch/arm64/boot/dts/mediatek/mt8365.dtsi line 577
Quoted 10 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +10
-0+ #size-cells = <0>; + status = "disabled"; + }; + + spi: spi@1100a000 { + compatible = "mediatek,mt8365-spi", + "mediatek,mt7622-spi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0 0x1100a000 0 0x100>;Reg goes after compatible.
Quoted 14 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +5
-0+ interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_LOW>; + clocks = <&topckgen CLK_TOP_UNIVPLL2_D4>, + <&topckgen CLK_TOP_SPI_SEL>, + <&infracfg CLK_IFR_SPI0>; + clock-names = "parent-clk", "sel-clk", "spi-clk";
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +8
-0+ status = "disabled"; + }; + + thermal: thermal@1100b000 { + compatible = "mediatek,mt8365-thermal"; + reg = <0 0x1100b000 0 0x1000>; + interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_LOW>; + clocks = <&infracfg CLK_IFR_THERM>,arch/arm64/boot/dts/mediatek/mt8365.dtsi line 600
Quoted 10 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +10
-0+ <&infracfg CLK_IFR_AUXADC>; + clock-names = "therm", "auxadc"; + mediatek,auxadc = <&auxadc>; + mediatek,apmixedsys = <&apmixedsys>; + nvmem-cells = <&thermal_calibration>; + nvmem-cell-names = "calibration-data"; + #thermal-sensor-cells = <1>; + }; + + disp_pwm: disp-pwm@1100e000 {Generic node names, so "pwm"
Quoted 119 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +28
-0+ compatible = "mediatek,mt8365-disp-pwm", + "mediatek,mt8183-disp-pwm"; + reg = <0 0x1100e000 0 0x1000>; + #pwm-cells = <2>; + clocks = <&topckgen CLK_TOP_DISP_PWM_SEL>, + <&infracfg CLK_IFR_DISP_PWM>; + clock-names = "main", "mm"; + power-domains = <&spm MT8365_POWER_DOMAIN_MM>; + status = "disabled"; + }; + + i2c3: i2c@1100f000 { + compatible = "mediatek,mt8365-i2c", + "mediatek,mt8168-i2c"; + reg = <0 0x1100f000 0 0xa0>, + <0 0x11000200 0 0x80>; + interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_LOW>; + clock-div = <1>; + clocks = <&infracfg CLK_IFR_I2C3_AXI>, + <&infracfg CLK_IFR_AP_DMA>; + clock-names = "main", "dma"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + ssusb: usb@11201000 { + compatible = "mediatek,mt8365-mtu3","mediatek,mtu3";
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +23
-0+ reg = <0 0x11201000 0 0x2e00>, + <0 0x11203e00 0 0x0100>; + reg-names = "mac", "ippc"; + interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_LOW>; + phys = <&u2port0 PHY_TYPE_USB2>, + <&u2port1 PHY_TYPE_USB2>; + clocks = <&topckgen CLK_TOP_SSUSB_TOP_CK_EN>, + <&infracfg CLK_IFR_SSUSB_REF>, + <&infracfg CLK_IFR_SSUSB_SYS>, + <&infracfg CLK_IFR_ICUSB>; + clock-names = "sys_ck", "ref_ck", "mcu_ck", + "dma_ck"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + status = "disabled"; + + usb_host: usb@11200000 { + compatible = "mediatek,mt8365-xhci", + "mediatek,mtk-xhci"; + reg = <0 0x11200000 0 0x1000>; + reg-names = "mac"; + interrupts = <GIC_SPI 67
IRQ_TYPE_LEVEL_LOW>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ clocks = <&topckgen
CLK_TOP_SSUSB_TOP_CK_EN>,arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +4
-0+ <&infracfg CLK_IFR_SSUSB_REF>, + <&infracfg CLK_IFR_SSUSB_SYS>, + <&infracfg CLK_IFR_ICUSB>, + <&infracfg
CLK_IFR_SSUSB_XHCI>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ clock-names = "sys_ck", "ref_ck","
mcu_ck",arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +7
-0+ "dma_ck", "xhci_ck"; + status = "disabled"; + }; + }; + + mmc0: mmc@11230000 { + compatible = "mediatek,mt8365-mmc","mediatek,mt8183-mmc";
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +12
-0+ reg = <0 0x11230000 0 0x1000>, + <0 0x11cd0000 0 0x1000>; + interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_LOW>; + clocks = <&topckgen CLK_TOP_MSDC50_0_SEL>, + <&infracfg CLK_IFR_MSDC0_HCLK>, + <&infracfg CLK_IFR_MSDC0_SRC>; + clock-names = "source", "hclk", "source_cg"; + status = "disabled"; + }; + + mmc1: mmc@11240000 { + compatible = "mediatek,mt8365-mmc","mediatek,mt8183-mmc";
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +35
-0+ reg = <0 0x11240000 0 0x1000>, + <0 0x11c90000 0 0x1000>; + interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_LOW>; + clocks = <&topckgen CLK_TOP_MSDC30_1_SEL>, + <&infracfg CLK_IFR_MSDC1_HCLK>, + <&infracfg CLK_IFR_MSDC1_SRC>; + clock-names = "source", "hclk", "source_cg"; + status = "disabled"; + }; + + ethernet: ethernet@112a0000 { + compatible = "mediatek,mt8365-eth"; + reg = <0 0x112a0000 0 0x1000>; + mediatek,pericfg = <&infracfg>; + interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&topckgen CLK_TOP_ETH_SEL>, + <&infracfg CLK_IFR_NIC_AXI>, + <&infracfg CLK_IFR_NIC_SLV_AXI>; + clock-names = "core", "reg", "trans"; + status = "disabled"; + }; + + mipi_tx0: dsi-phy@11c00000 { + compatible = "mediatek,mt8365-mipi-tx", + "mediatek,mt8183-mipi-tx"; + reg = <0 0x11c00000 0 0x800>; + clocks = <&clk26m>; + clock-names = "ref_clk"; + #clock-cells = <0>; + #phy-cells = <0>; + clock-output-names = "mipi_tx0_pll"; + }; + + efuse: efuse@11c50000 { + compatible = "mediatek,mt8365-efuse","mediatek,efuse";
arch/arm64/boot/dts/mediatek/mt8365.dtsi line 721
Quoted 10 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +10
-0+ reg = <0 0x11c50000 0 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + + thermal_calibration: calib@180 { + reg = <0x180 0xc>; + }; + }; + + u3phy: t-phy@11cc0000 {s/t-phy/phy/
Quoted 4 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi line 725
Quoted 4 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +4
-0+ compatible = "mediatek,mt8365-tphy", + "mediatek,generic-tphy-v2"; + #address-cells = <2>; + #phy-cells = <1>;
remove #phy-cells, it's only used in subnode;
Quoted 5 lines
address-cells, then size, then phy
arch/arm64/boot/dts/mediatek/mt8365.dtsi
Quoted 2 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +2
-0+ #size-cells = <2>; + ranges;
Prefer to use ranges with value
Quoted 83 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi
Quoted 1 line
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ status = "okay";No need for status ok.
arch/arm64/boot/dts/mediatek/mt8365.dtsi line 736
Quoted 10 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +4
-0+ + u2port0: usb-phy@11cc0000 { + reg = <0 0x11cc0000 0 0x400>; + clocks = <&topckgen
CLK_TOP_SSUSB_PHY_CK_EN>,arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ <&topckgen
CLK_TOP_USB20_48M_EN>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +3
-0+ clock-names = "ref", "da_ref"; + #phy-cells = <1>; + status = "okay";Ditto
Quoted 25 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +5
-0+ }; + + u2port1: usb-phy@11cc1000 { + reg = <0 0x11cc1000 0 0x400>; + clocks = <&topckgen
CLK_TOP_SSUSB_PHY_CK_EN>,arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +1
-0+ <&topckgen
CLK_TOP_USB20_48M_EN>;arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +8
-0+ clock-names = "ref", "da_ref"; + #phy-cells = <1>; + status = "okay"; + }; + }; + + mfgcfg: syscon@13000000 { + compatible = "mediatek,mt8365-mfgcfg","syscon";
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +8
-0+ reg = <0 0x13000000 0 0x1000>; + #clock-cells = <1>; + }; + + mmsys: syscon@14000000 { + compatible = "mediatek,mt8365-mmsys", "syscon"; + reg = <0 0x14000000 0 0x1000>; + #clock-cells = <1>;arch/arm64/boot/dts/mediatek/mt8365.dtsi line 768
Quoted 10 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +10
-0+ }; + + mutex: mutex@14001000 { + compatible = "mediatek,mt8365-disp-mutex"; + reg = <0 0x14001000 0 0x1000>; + interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&spm MT8365_POWER_DOMAIN_MM>; + }; + + smi_common: smi@14002000 {s/smi/memory-controller/ in node name?
arch/arm64/boot/dts/mediatek/mt8365.dtsi line 780
Quoted 12 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +12
-0+ compatible = "mediatek,mt8365-smi-common", + "mediatek,mt8186-smi-common"; + reg = <0 0x14002000 0 0x1000>; + clocks = <&mmsys CLK_MM_MM_SMI_COMMON>, + <&mmsys CLK_MM_MM_SMI_COMMON>, + <&mmsys CLK_MM_MM_SMI_COMM0>, + <&mmsys CLK_MM_MM_SMI_COMM1>; + clock-names = "apb", "smi", "gals0", "gals1"; + power-domains = <&spm MT8365_POWER_DOMAIN_MM>; + }; + + larb0: larb@14003000 {The same?
arch/arm64/boot/dts/mediatek/mt8365.dtsi line 788
Quoted 8 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +8
-0+ compatible = "mediatek,mt8365-smi-larb", + "mediatek,mt8186-smi-larb"; + reg = <0 0x14003000 0 0x1000>; + mediatek,smi = <&smi_common>; + clocks = <&mmsys CLK_MM_MM_SMI_LARB0>, + <&mmsys CLK_MM_MM_SMI_LARB0>; + clock-names = "apb", "smi"; + power-domains = <&spm MT8365_POWER_DOMAIN_MM>;Best regards,
Krzysztof
Re: [PATCH 16/17] arm64: dts: mediatek: add mt8365 device-tree
In reply to Fabien ParentHi Fabien,
arch/arm64/boot/dts/mediatek/mt8365.dtsi line 1035
Quoted 7 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +7
-0+ tzts4: tzts4-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&thermal 4>; + trips {}; + cooling-maps {}; + };
AFAIK mt8365 has only 3 thermal sensors, therefore tzts4 should not be added.
Regards,
Amjad
Re: [PATCH 16/17] arm64: dts: mediatek: add mt8365 device-tree
Hi Fabien,
Quoted 11 lines · Amjad Ouled-Ameur
Hi Fabien,
arch/arm64/boot/dts/mediatek/mt8365.dtsi line 1035
Quoted 7 lines
arch/arm64/boot/dts/mediatek/mt8365.dtsi new file +7
-0+ tzts4: tzts4-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&thermal 4>; + trips {}; + cooling-maps {}; + };AFAIK mt8365 has only 3 thermal sensors, therefore tzts4 should not be added.
I discussed this further with MediaTek. tzts1, tzts2, tzts3 and tzts4 are used
for test-purpose only. Since they do not have trip points, thermal core wouldn't
register them anyway. Thus, I think we should remove them altogether. Only
cpu_thermal zone is relevant and should remain.
Regards,
Amjad
Quoted 2 lines
Regards,
Amjad
Re: [PATCH 16/17] arm64: dts: mediatek: add mt8365 device-tree
In reply to Fabien ParentHi Fabien,
Could you please add CPUIDLE support:
arch/arm64/boot/dts/mediatek/mt8365.dtsi +35 -0
@@ -59,6 +59,7 @@ cpu0: cpu@0 { clocks = <&mcucfg CLK_MCU_BUS_SEL>, <&apmixedsys CLK_APMIXED_MAINPLL>; clock-names = "cpu", "intermediate"; + cpu-idle-states = <&MCDI_CPU &MCDI_CLUSTER &DPIDLE>; operating-points-v2 = <&cluster0_opp>; #cooling-cells = <2>; enable-method = "psci";
@@ -72,6 +73,7 @@ cpu1: cpu@1 { clocks = <&mcucfg CLK_MCU_BUS_SEL>, <&apmixedsys CLK_APMIXED_MAINPLL>; clock-names = "cpu", "intermediate", "armpll"; + cpu-idle-states = <&MCDI_CPU &MCDI_CLUSTER &DPIDLE>; operating-points-v2 = <&cluster0_opp>; #cooling-cells = <2>; enable-method = "psci";
@@ -85,6 +87,7 @@ cpu2: cpu@2 { clocks = <&mcucfg CLK_MCU_BUS_SEL>, <&apmixedsys CLK_APMIXED_MAINPLL>; clock-names = "cpu", "intermediate", "armpll"; + cpu-idle-states = <&MCDI_CPU &MCDI_CLUSTER &DPIDLE>; operating-points-v2 = <&cluster0_opp>; #cooling-cells = <2>; enable-method = "psci";
@@ -98,10 +101,42 @@ cpu3: cpu@3 { clocks = <&mcucfg CLK_MCU_BUS_SEL>, <&apmixedsys CLK_APMIXED_MAINPLL>; clock-names = "cpu", "intermediate", "armpll"; + cpu-idle-states = <&MCDI_CPU &MCDI_CLUSTER &DPIDLE>; operating-points-v2 = <&cluster0_opp>; #cooling-cells = <2>; enable-method = "psci"; }; + + idle-states { + entry-method = "psci"; + + MCDI_CPU: mcdi-cpu { + compatible = "arm,idle-state"; + local-timer-stop; + arm,psci-suspend-param = <0x00010001>; + entry-latency-us = <300>; + exit-latency-us = <200>; + min-residency-us = <1000>; + }; + + MCDI_CLUSTER: mcdi-cluster { + compatible = "arm,idle-state"; + local-timer-stop; + arm,psci-suspend-param = <0x01010001>; + entry-latency-us = <350>; + exit-latency-us = <250>; + min-residency-us = <1200>; + }; + + DPIDLE: dpidle { + compatible = "arm,idle-state"; + local-timer-stop; + arm,psci-suspend-param = <0x01010004>; + entry-latency-us = <300>; + exit-latency-us = <800>; + min-residency-us = <3300>; + }; + }; }; cluster0_opp: opp-table-0 {
I have tested it on i350 evk and each idle state is used properly.
Regards,
Amjad
Signature · 3 lines
linux-phy mailing list [email protected] https://lists.infradead.org/mailman/listinfo/linux-phy
PATCH 17/17 arm64: dts: mediatek: add mt8365-evk board device-tree
In reply to Fabien ParentAdd device-tree for the MT8365-EVK board. The MT8365 EVK board has the following IOs:
* DPI <-> HDMI bridge and HDMI connector.
* 2 audio jack
* 1 USB Type-A Host port
* 2 UART to USB port
* 1 battery connector
* 1 eMMC
* 1 SD card
* 2 camera connectors
* 1 M.2 slot for connectivity
* 1 DSI connector + touchscreen connector
* RPI compatible header
* 1 Ethernet port
--- arch/arm64/boot/dts/mediatek/Makefile | 1 + arch/arm64/boot/dts/mediatek/mt8365-evk.dts | 578 ++++++++++++++++++++ 2 files changed, 579 insertions(+) create mode 100644 arch/arm64/boot/dts/mediatek/mt8365-evk.dts
arch/arm64/boot/dts/mediatek/Makefile +1 -0
@@ -40,4 +40,5 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-pumpkin.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt8192-evb.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-demo.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-evb.dtb +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8365-evk.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt8516-pumpkin.dtb
arch/arm64/boot/dts/mediatek/mt8365-evk.dts new file +578 -0
578 lines not on this page · raw message
Signature · 1 line
2.36.1
Re: [PATCH 17/17] arm64: dts: mediatek: add mt8365-evk board device-tree
Quoted 6 lines · Fabien Parent
Add device-tree for the MT8365-EVK board. The MT8365 EVK board has the following IOs:
* DPI <-> HDMI bridge and HDMI connector.
* 2 audio jack
* 1 USB Type-A Host port
* 2 UART to USB port
Quoted 8 lines
* 1 battery connector
* 1 eMMC
* 1 SD card
* 2 camera connectors
* 1 M.2 slot for connectivity
* 1 DSI connector + touchscreen connector
* RPI compatible header
* 1 Ethernet port
Thank you for your patch. There is something to discuss/improve.
Quoted 66 lines
Signed-off-by Fabien Parent <[email protected]>--- arch/arm64/boot/dts/mediatek/Makefile | 1 + arch/arm64/boot/dts/mediatek/mt8365-evk.dts | 578 ++++++++++++++++++++ 2 files changed, 579 insertions(+) create mode 100644 arch/arm64/boot/dts/mediatek/mt8365-evk.dtsarch/arm64/boot/dts/mediatek/Makefile +1
-0@@ -40,4 +40,5 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-pumpkin.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt8192-evb.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-demo.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-evb.dtb +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8365-evk.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt8516-pumpkin.dtbarch/arm64/boot/dts/mediatek/mt8365-evk.dts new file +42
-0@@ -0,0 +1,578 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) 2021 BayLibre, SAS. + * Author: Fabien Parent <[email protected]> + */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/pinctrl/mt8365-pinfunc.h> +#include "mt8365.dtsi" +#include "mt6357.dtsi" + +/ { + model = "MediaTek MT8365 Open Platform EVK"; + compatible = "mediatek,mt8365-evk", "mediatek,mt8365"; + + aliases { + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:921600n8"; + }; + + connector { + compatible = "hdmi-connector"; + label = "hdmi"; + type = "a"; + + port { + hdmi_connector_in: endpoint { + remote-endpoint = <&hdmi_connector_out>; + }; + }; + }; + + firmware { + optee { + compatible = "linaro,optee-tz"; + method = "smc";
arch/arm64/boot/dts/mediatek/mt8365-evk.dts line 52
Quoted 10 lines
arch/arm64/boot/dts/mediatek/mt8365-evk.dts new file +10
-0+ }; + }; + + gpio-keys { + compatible = "gpio-keys"; + input-name = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&gpio_keys>; + + volume-up {
key-volume-up, volume-up-key or key-0
Quoted 105 lines
arch/arm64/boot/dts/mediatek/mt8365-evk.dts new file +105
-0+ gpios = <&pio 24 GPIO_ACTIVE_LOW>; + label = "volume_up"; + linux,code = <KEY_VOLUMEUP>; + wakeup-source; + debounce-interval = <15>; + }; + }; + + memory@40000000 { + device_type = "memory"; + reg = <0 0x40000000 0 0xc0000000>; + }; + + usb_otg_vbus: regulator-2 { + compatible = "regulator-fixed"; + regulator-name = "otg_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&pio 16 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + /* 12 MiB reserved for OP-TEE (BL32) + * +-----------------------+ 0x43e0_0000 + * | SHMEM 2MiB | + * +-----------------------+ 0x43c0_0000 + * | | TA_RAM 8MiB | + * + TZDRAM +--------------+ 0x4340_0000 + * | | TEE_RAM 2MiB | + * +-----------------------+ 0x4320_0000 + */ + optee_reserved: optee@43200000 { + no-map; + reg = <0 0x43200000 0 0x00c00000>; + }; + }; +}; + +&cpu0 { + proc-supply = <&mt6357_vproc_reg>; + sram-supply = <&mt6357_vsram_proc_reg>; +}; + +&cpu1 { + proc-supply = <&mt6357_vproc_reg>; + sram-supply = <&mt6357_vsram_proc_reg>; +}; + +&cpu2 { + proc-supply = <&mt6357_vproc_reg>; + sram-supply = <&mt6357_vsram_proc_reg>; +}; + +&cpu3 { + proc-supply = <&mt6357_vproc_reg>; + sram-supply = <&mt6357_vsram_proc_reg>; +}; + +&dpi0 { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&dpi_func_pins>; + pinctrl-1 = <&dpi_idle_pins>; + assigned-clocks = <&topckgen CLK_TOP_DPI0_SEL>; + assigned-clock-parents = <&topckgen CLK_TOP_LVDSPLL_D4>; + + /* + * Ethernet and HDMI are sharing pins. + * Only one can be enabled at a time and require the physical switch + * SW2101 to be set on DPI position + */ + status = "okay"; + + port { + dpi_out: endpoint { + remote-endpoint = <&it66121_in>; + }; + }; +}; + +ðernet { + pinctrl-names = "default"; + pinctrl-0 = <ðernet_pins>; + phy-handle = <ð_phy>; + phy-mode = "rmii"; + mac-address = [00 00 00 00 00 00]; + + /* + * Ethernet and HDMI are sharing pins. + * Only one can be enabled at a time and require the physical switch + * SW2101 to be set on LAN position + */ + status = "disabled"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + eth_phy: ethernet-phy@0 { + reg = <0>; + };
arch/arm64/boot/dts/mediatek/mt8365-evk.dts line 167
Quoted 10 lines
arch/arm64/boot/dts/mediatek/mt8365-evk.dts new file +10
-0+ }; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; + clock-frequency = <100000>; + status = "okay"; + #address-cells = <1>; + #size-cells = <0>;
You defined address/size in DTSI.
arch/arm64/boot/dts/mediatek/mt8365-evk.dts line 179
Quoted 12 lines
arch/arm64/boot/dts/mediatek/mt8365-evk.dts new file +12
-0+ + it66121hdmitx: hdmi@4c { + compatible = "ite,it66121"; + pinctrl-names = "default"; + pinctrl-0 = <&ite_pins>; + vcn33-supply = <&mt6357_vibr_reg>; + vcn18-supply = <&mt6357_vsim2_reg>; + vrf12-supply = <&mt6357_vrf12_reg>; + reset-gpios = <&pio 69 GPIO_ACTIVE_LOW>; + interrupts-extended = <&pio 68 IRQ_TYPE_LEVEL_LOW>; + #sound-dai-cells = <0>; + reg = <0x4c>;
Put reg after compatible.
Quoted 17 lines
arch/arm64/boot/dts/mediatek/mt8365-evk.dts new file +17
-0+ + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + it66121_in: endpoint { + bus-width = <12>; + remote-endpoint = <&dpi_out>; + }; + }; + + port@1 { + reg = <1>; +
arch/arm64/boot/dts/mediatek/mt8365-evk.dts line 206
Quoted 10 lines
arch/arm64/boot/dts/mediatek/mt8365-evk.dts new file +10
-0+ hdmi_connector_out: endpoint { + remote-endpoint = <&hdmi_connector_in>; + }; + }; + }; + }; +}; + +&mmc0 { + status = "okay";
Status okay goes to the end. In some nodes you keep that style, in some not. Confusing.
Quoted 56 lines
arch/arm64/boot/dts/mediatek/mt8365-evk.dts new file +56
-0+ pinctrl-names = "default", "state_uhs"; + pinctrl-0 = <&mmc0_pins_default>; + pinctrl-1 = <&mmc0_pins_uhs>; + bus-width = <8>; + max-frequency = <200000000>; + cap-mmc-highspeed; + mmc-hs200-1_8v; + mmc-hs400-1_8v; + cap-mmc-hw-reset; + no-sdio; + no-sd; + hs400-ds-delay = <0x12012>; + vmmc-supply = <&mt6357_vemc_reg>; + vqmmc-supply = <&mt6357_vio18_reg>; + assigned-clocks = <&topckgen CLK_TOP_MSDC50_0_SEL>; + assigned-clock-parents = <&topckgen CLK_TOP_MSDCPLL>; + non-removable; +}; + +&mmc1 { + pinctrl-names = "default", "state_uhs"; + pinctrl-0 = <&mmc1_pins_default>; + pinctrl-1 = <&mmc1_pins_uhs>; + cd-gpios = <&pio 76 GPIO_ACTIVE_LOW>; + bus-width = <4>; + max-frequency = <200000000>; + cap-sd-highspeed; + sd-uhs-sdr50; + sd-uhs-sdr104; + vmmc-supply = <&mt6357_vmch_reg>; + vqmmc-supply = <&mt6357_vio18_reg>; + status = "okay"; +}; + +&mt6357_pmic { + interrupt-parent = <&pio>; + interrupts = <145 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + #interrupt-cells = <2>; +}; + +&mt6357_vibr_reg { + regulator-always-on; +}; + +/* Needed by MSDC1 */ +&mt6357_vmc_reg { + regulator-always-on; +}; + +&mt6357_vrf12_reg { + regulator-always-on; +}; + +&mt6357_vsim2_reg { + regulator-always-on;
arch/arm64/boot/dts/mediatek/mt8365-evk.dts line 272
Quoted 10 lines
arch/arm64/boot/dts/mediatek/mt8365-evk.dts new file +10
-0+}; + +&mt6357keys { + power-key { + label = "power"; + linux,keycodes = <KEY_POWER>; + wakeup-source; + }; + + volume-down {
volume-down-key
arch/arm64/boot/dts/mediatek/mt8365-evk.dts line 274
Quoted 2 lines
arch/arm64/boot/dts/mediatek/mt8365-evk.dts new file +2
-0+ label = "volume_down"; + linux,keycodes = <KEY_VOLUMEDOWN>;
Best regards,
Krzysztof
Quoted 16 lines · Fabien Parent
This patch series adds support for the MT8365 EVK board.
This series has dependencies on the following series:
https://patchwork.kernel.org/project/linux-mediatek/list/?series=646256
https://patchwork.kernel.org/project/linux-mediatek/list/?series=646091
https://patchwork.kernel.org/project/linux-mediatek/list/?series=646083
https://patchwork.kernel.org/project/linux-mediatek/list/?series=646081
https://patchwork.kernel.org/project/linux-mediatek/list/?series=646076
https://patchwork.kernel.org/project/linux-mediatek/list/?series=646068
https://patchwork.kernel.org/project/linux-mediatek/list/?series=646020
https://patchwork.kernel.org/project/linux-mediatek/list/?series=646052
https://lore.kernel.org/r/[email protected]
https://lore.kernel.org/r/[email protected]
https://lore.kernel.org/r/[email protected]
https://lore.kernel.org/r/[email protected]
https://lore.kernel.org/all/[email protected]/
Eh... and how we are supposed to test or apply this? Such dependencies could mean none of automated tools will pick it up, so your patchset has to wait till dependencies got merged.
Best regards,
Krzysztof
Signature · 3 lines
linux-phy mailing list [email protected] https://lists.infradead.org/mailman/listinfo/linux-phy
Mark Brown
maintainerRe: (subset) [PATCH 00/17] Add support for MT8365 EVK board
In reply to Fabien ParentQuoted 17 lines · Fabien Parent
This patch series adds support for the MT8365 EVK board.
This series has dependencies on the following series:
https://patchwork.kernel.org/project/linux-mediatek/list/?series=646256
https://patchwork.kernel.org/project/linux-mediatek/list/?series=646091
https://patchwork.kernel.org/project/linux-mediatek/list/?series=646083
https://patchwork.kernel.org/project/linux-mediatek/list/?series=646081
https://patchwork.kernel.org/project/linux-mediatek/list/?series=646076
https://patchwork.kernel.org/project/linux-mediatek/list/?series=646068
https://patchwork.kernel.org/project/linux-mediatek/list/?series=646020
https://patchwork.kernel.org/project/linux-mediatek/list/?series=646052
https://lore.kernel.org/r/[email protected]
https://lore.kernel.org/r/[email protected]
https://lore.kernel.org/r/[email protected]
https://lore.kernel.org/r/[email protected]
https://lore.kernel.org/all/[email protected]/
Quoted 1 line
[...]
Applied to
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git for-next
Thanks!
[09/17] dt-bindings: spi: mt65xx: add MT8365 SoC bindings
commit: 901fc8e8079e401f3240006cab6629e65579701c
All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent to Linus during the next merge window (or sooner if it is a bug fix), however if problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying to this mail.
Thanks,
Mark