5.4.202-rc1 review

This is the start of the stable review cycle for the 5.4.202 release. There are 60 patches in this series, all will be posted as a response to this one. If anyone has any issues with these being applied, please let me know.

Responses should be made by Wed, 29 Jun 2022 11:19:09 +0000. Anything received after that time might be too late.

The whole patch series can be found in one patch at:

	https://www.kernel.org/pub/linux/kernel/v5.x/stable-review/patch-5.4.202-rc1.gz

or in the git tree and branch at:
git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git linux-5.4.y
and the diffstat can be found below.

thanks,

greg k-h

-------------
Pseudo-Shortlog of commits:

Greg Kroah-Hartman <[email protected]>

    Linux 5.4.202-rc1

Jason A. Donenfeld <[email protected]>
powerpc/pseries: wire up rng during setup_arch()

Masahiro Yamada <[email protected]>
kbuild: link vmlinux only once for CONFIG_TRIM_UNUSED_KSYMS (2nd attempt)

Jason A. Donenfeld <[email protected]>

    random: update comment from copy_to_user() -> copy_to_iter()

Masahiro Yamada <[email protected]>
modpost: fix section mismatch check for exported init/exit sections

Miaoqian Lin <[email protected]>
ARM: cns3xxx: Fix refcount leak in cns3xxx_init

Miaoqian Lin <[email protected]>
ARM: Fix refcount leak in axxia_boot_secondary

Miaoqian Lin <[email protected]>
soc: bcm: brcmstb: pm: pm-arm: Fix refcount leak in brcmstb_pm_probe

Miaoqian Lin <[email protected]>
ARM: exynos: Fix refcount leak in exynos_map_pmu

Lucas Stach <[email protected]>
ARM: dts: imx6qdl: correct PU regulator ramp delay

Jason A. Donenfeld <[email protected]>
powerpc/powernv: wire up rng during setup_arch

Andrew Donnellan <[email protected]>
powerpc/rtas: Allow ibm,platform-dump RTAS call with null buffer address

Naveen N. Rao <[email protected]>
powerpc: Enable execve syscall exit tracepoint

Helge Deller <[email protected]>
parisc: Enable ARCH_HAS_STRICT_MODULE_RWX

Liang He <[email protected]>
xtensa: Fix refcount leak bug in time.c

Liang He <[email protected]>
xtensa: xtfpga: Fix refcount leak bug in setup

Hans de Goede <[email protected]>
iio: adc: axp288: Override TS pin bias current for some models

Olivier Moysan <[email protected]>
iio: adc: stm32: fix maximum clock rate for stm32mp15x

Vincent Whitchurch <[email protected]>
iio: trigger: sysfs: fix use-after-free on remove

Zheyu Ma <[email protected]>
iio: gyro: mpu3050: Fix the error handling in mpu3050_power_up()

Haibo Chen <[email protected]>
iio: accel: mma8452: ignore the return value of reset operation

Dmitry Rokosov <[email protected]>
iio:accel:mxc4005: rearrange iio trigger get and register

Dmitry Rokosov <[email protected]>
iio:accel:bma180: rearrange iio trigger get and register

Dmitry Rokosov <[email protected]>
iio:chemical:ccs811: rearrange iio trigger get and register

Xu Yang <[email protected]>
usb: chipidea: udc: check request status before setting device address

Mathias Nyman <[email protected]>
xhci: turn off port power in shutdown

Baruch Siach <[email protected]>
iio: adc: vf610: fix conversion mode sysfs node name

Thomas Richter <[email protected]>
s390/cpumf: Handle events cycles and instructions identical

Dan Carpenter <[email protected]>
gpio: winbond: Fix error code in winbond_gpio_get()

Jakub Kicinski <[email protected]>
Revert "net/tls: fix tls_sk_proto_close executed repeatedly"

Stephan Gerhold <[email protected]>
virtio_net: fix xdp_rxq_info bug after suspend/resume

Kai-Heng Feng <[email protected]>
igb: Make DMA faster when CPU is active on the PCIe link

Aidan MacDonald <[email protected]>
regmap-irq: Fix a bug in regmap_irq_enable() for type_in_mask chips

Anatolii Gerasymenko <[email protected]>
ice: ethtool: advertise 1000M speeds properly

David Howells <[email protected]>
afs: Fix dynamic root getattr

huhai <[email protected]>
MIPS: Remove repetitive increase irq_err_count

Julien Grall <[email protected]>
x86/xen: Remove undefined behavior in setup_features()

Gerd Hoffmann <[email protected]>
udmabuf: add back sanity check

Ziyang Xuan <[email protected]>
net/tls: fix tls_sk_proto_close executed repeatedly

Eric Dumazet <[email protected]>
erspan: do not assume transport header is always set

Miaoqian Lin <[email protected]>
drm/msm/mdp4: Fix refcount leak in mdp4_modeset_init_intf

Peilin Ye <[email protected]>
net/sched: sch_netem: Fix arithmetic in netem_dump() for 32-bit platforms

Jay Vosburgh <[email protected]>
bonding: ARP monitor spams NETDEV_NOTIFY_PEERS notifiers

Claudiu Manoil <[email protected]>
phy: aquantia: Fix AN when higher speeds than 1G are not advertised

Jon Maxwell <[email protected]>
bpf: Fix request_sock leak in sk lookup helpers

Macpaul Lin <[email protected]>
USB: serial: option: add Quectel RM500K module support

Yonglin Tan <[email protected]>
USB: serial: option: add Quectel EM05-G modem

Carlo Lobrano <[email protected]>

    USB: serial: option: add Telit LE910Cx 0x1250 composition

Jason A. Donenfeld <[email protected]>
random: quiet urandom warning ratelimit suppression message

Mikulas Patocka <[email protected]>
dm mirror log: clear log bits up to BITS_PER_LONG boundary

Nikos Tsironis <[email protected]>
dm era: commit metadata in postsuspend after worker stops

Edward Wu <[email protected]>

    ata: libata: add qc->flags in ata_qc_complete_template tracepoint

Sascha Hauer <[email protected]>
mtd: rawnand: gpmi: Fix setting busy timeout setting

Chevron Li <[email protected]>
mmc: sdhci-pci-o2micro: Fix card detect by dealing with debouncing

Rosemarie O'Riorden <[email protected]>
net: openvswitch: fix parsing of nw_proto for IPv6 fragments

Tim Crawford <[email protected]>
ALSA: hda/realtek: Add quirk for Clevo PD70PNT

Kailang Yang <[email protected]>
ALSA: hda/realtek - ALC897 headset MIC no sound

Takashi Iwai <[email protected]>
ALSA: hda/conexant: Fix missing beep setup

Takashi Iwai <[email protected]>
ALSA: hda/via: Fix missing beep setup

Jason A. Donenfeld <[email protected]>
random: schedule mix_interrupt_randomness() less often

Jiri Slaby <[email protected]>
vt: drop old FONT ioctls

-------------

Diffstat:

 Documentation/ABI/testing/sysfs-bus-iio-vf610 |   2 +-
 Makefile                                      |   6 +-
 arch/arm/boot/dts/imx6qdl.dtsi                |   2 +-
 arch/arm/mach-axxia/platsmp.c                 |   1 +
 arch/arm/mach-cns3xxx/core.c                  |   2 +
 arch/arm/mach-exynos/exynos.c                 |   1 +
 arch/mips/vr41xx/common/icu.c                 |   2 -
 arch/parisc/Kconfig                           |   1 +
 arch/powerpc/kernel/process.c                 |   2 +-
 arch/powerpc/kernel/rtas.c                    |  11 +-
 arch/powerpc/platforms/powernv/powernv.h      |   2 +
 arch/powerpc/platforms/powernv/rng.c          |  52 ++++++---
 arch/powerpc/platforms/powernv/setup.c        |   2 +
 arch/powerpc/platforms/pseries/pseries.h      |   2 +
 arch/powerpc/platforms/pseries/rng.c          |  11 +-
 arch/powerpc/platforms/pseries/setup.c        |   2 +
 arch/s390/kernel/perf_cpum_cf.c               |  22 +++-
 arch/xtensa/kernel/time.c                     |   1 +
 arch/xtensa/platforms/xtfpga/setup.c          |   1 +
 drivers/base/regmap/regmap-irq.c              |   5 +-
 drivers/char/random.c                         |   6 +-
 drivers/dma-buf/udmabuf.c                     |   5 +-
 drivers/gpio/gpio-vr41xx.c                    |   2 -
 drivers/gpio/gpio-winbond.c                   |   7 +-
 drivers/gpu/drm/msm/disp/mdp4/mdp4_kms.c      |   2 +
 drivers/iio/accel/bma180.c                    |   3 +-
 drivers/iio/accel/mma8452.c                   |  10 +-
 drivers/iio/accel/mxc4005.c                   |   4 +-
 drivers/iio/adc/axp288_adc.c                  |   8 ++
 drivers/iio/adc/stm32-adc-core.c              |   2 +-
 drivers/iio/chemical/ccs811.c                 |   4 +-
 drivers/iio/gyro/mpu3050-core.c               |   1 +
 drivers/iio/trigger/iio-trig-sysfs.c          |   1 +
 drivers/md/dm-era-target.c                    |   8 +-
 drivers/md/dm-log.c                           |   2 +-
 drivers/mmc/host/sdhci-pci-o2micro.c          |   2 +
 drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c    |   2 +-
 drivers/net/bonding/bond_main.c               |   4 +-
 drivers/net/ethernet/intel/ice/ice_ethtool.c  |  39 ++++++-
 drivers/net/ethernet/intel/igb/igb_main.c     |  12 +--
 drivers/net/phy/aquantia_main.c               |  15 ++-
 drivers/net/virtio_net.c                      |  25 ++---
 drivers/soc/bcm/brcmstb/pm/pm-arm.c           |   1 +
 drivers/tty/vt/vt.c                           |  39 +------
 drivers/tty/vt/vt_ioctl.c                     | 147 --------------------------
 drivers/usb/chipidea/udc.c                    |   3 +
 drivers/usb/host/xhci-hub.c                   |   2 +-
 drivers/usb/host/xhci.c                       |  15 ++-
 drivers/usb/host/xhci.h                       |   2 +
 drivers/usb/serial/option.c                   |   6 ++
 drivers/xen/features.c                        |   2 +-
 fs/afs/inode.c                                |   3 +-
 include/linux/kd.h                            |   8 --
 include/linux/ratelimit.h                     |  12 ++-
 include/trace/events/libata.h                 |   1 +
 net/core/filter.c                             |  34 ++++--
 net/ipv4/ip_gre.c                             |  15 ++-
 net/ipv6/ip6_gre.c                            |  15 ++-
 net/openvswitch/flow.c                        |   2 +-
 net/sched/sch_netem.c                         |   4 +-
 scripts/mod/modpost.c                         |   2 +-
 sound/pci/hda/patch_conexant.c                |   4 +-
 sound/pci/hda/patch_realtek.c                 |  10 ++
 sound/pci/hda/patch_via.c                     |   4 +-
 64 files changed, 315 insertions(+), 310 deletions(-)

From: Jiri Slaby <[email protected]>

commit ff2047fb755d4415ec3c70ac799889371151796d upstream.

Drop support for these ioctls:
* PIO_FONT, PIO_FONTX
* GIO_FONT, GIO_FONTX
* PIO_FONTRESET

As was demonstrated by commit 90bfdeef83f1 (tty: make FONTX ioctl use the tty pointer they were actually passed), these ioctls are not used from userspace, as:
1) they used to be broken (set up font on current console, not the open one) and racy (before the commit above)
2) KDFONTOP ioctl is used for years instead

Note that PIO_FONTRESET is defunct on most systems as VGA_CONSOLE is set on them for ages. That turns on BROKEN_GRAPHICS_PROGRAMS which makes PIO_FONTRESET just return an error.

We are removing KD_FONT_FLAG_OLD here as it was used only by these removed ioctls. kd.h header exists both in kernel and uapi headers, so we can remove the kernel one completely. Everyone includeing kd.h will now automatically get the uapi one.

There are now unused definitions of the ioctl numbers and "struct consolefontdesc" in kd.h, but as it is a uapi header, I am not touching these.

---
 drivers/tty/vt/vt.c       |   39 ------------
 drivers/tty/vt/vt_ioctl.c |  147 ----------------------------------------------
 include/linux/kd.h        |    8 --
 3 files changed, 3 insertions(+), 191 deletions(-)
 delete mode 100644 include/linux/kd.h

@@ -4541,16 +4541,8 @@ static int con_font_get(struct vc_data *
 
 	if (op->data && font.charcount > op->charcount)
 		rc = -ENOSPC;
-	if (!(op->flags & KD_FONT_FLAG_OLD)) {
-		if (font.width > op->width || font.height > op->height) 
-			rc = -ENOSPC;
-	} else {
-		if (font.width != 8)
-			rc = -EIO;
-		else if ((op->height && font.height > op->height) ||
-			 font.height > 32)
-			rc = -ENOSPC;
-	}
+	if (font.width > op->width || font.height > op->height)
+		rc = -ENOSPC;
 	if (rc)
 		goto out;
 

@@ -4578,7 +4570,7 @@ static int con_font_set(struct vc_data *
 		return -EINVAL;
 	if (op->charcount > 512)
 		return -EINVAL;
-	if (op->width <= 0 || op->width > 32 || op->height > 32)
+	if (op->width <= 0 || op->width > 32 || !op->height || op->height > 32)
 		return -EINVAL;
 	size = (op->width+7)/8 * 32 * op->charcount;
 	if (size > max_font_size)

@@ -4588,31 +4580,6 @@ static int con_font_set(struct vc_data *
 	if (IS_ERR(font.data))
 		return PTR_ERR(font.data);
 
-	if (!op->height) {		/* Need to guess font height [compat] */
-		int h, i;
-		u8 *charmap = font.data;
-
-		/*
-		 * If from KDFONTOP ioctl, don't allow things which can be done
-		 * in userland,so that we can get rid of this soon
-		 */
-		if (!(op->flags & KD_FONT_FLAG_OLD)) {
-			kfree(font.data);
-			return -EINVAL;
-		}
-
-		for (h = 32; h > 0; h--)
-			for (i = 0; i < op->charcount; i++)
-				if (charmap[32*i+h-1])
-					goto nonzero;
-
-		kfree(font.data);
-		return -EINVAL;
-
-	nonzero:
-		op->height = h;
-	}
-
 	font.charcount = op->charcount;
 	font.width = op->width;
 	font.height = op->height;

@@ -1,8 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-#ifndef _LINUX_KD_H
-#define _LINUX_KD_H
-
-#include <uapi/linux/kd.h>
-
-#define KD_FONT_FLAG_OLD		0x80000000	/* Invoked via old interface [compat] */
-#endif /* _LINUX_KD_H */

From: Jason A. Donenfeld <[email protected]>

commit 534d2eaf1970274150596fdd2bf552721e65d6b2 upstream.

It used to be that mix_interrupt_randomness() would credit 1 bit each time it ran, and so add_interrupt_randomness() would schedule mix() to run every 64 interrupts, a fairly arbitrary number, but nonetheless considered to be a decent enough conservative estimate.

Since e3e33fc2ea7f ("random: do not use input pool from hard IRQs"), mix() is now able to credit multiple bits, depending on the number of calls to add(). This was done for reasons separate from this commit, but it has the nice side effect of enabling this patch to schedule mix() less often.

Currently the rules are:
a) Credit 1 bit for every 64 calls to add().
b) Schedule mix() once a second that add() is called.
c) Schedule mix() once every 64 calls to add().

Rules (a) and (c) no longer need to be coupled. It's still important to have _some_ value in (c), so that we don't "over-saturate" the fast pool, but the once per second we get from rule (b) is a plenty enough baseline. So, by increasing the 64 in rule (c) to something larger, we avoid calling queue_work_on() as frequently during irq storms.

This commit changes that 64 in rule (c) to be 1024, which means we schedule mix() 16 times less often. And it does *not* need to change the 64 in rule (a).

---
 drivers/char/random.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

@@ -996,7 +996,7 @@ void add_interrupt_randomness(int irq)
 	if (new_count & MIX_INFLIGHT)
 		return;
 
-	if (new_count < 64 && !time_is_before_jiffies(fast_pool->last + HZ))
+	if (new_count < 1024 && !time_is_before_jiffies(fast_pool->last + HZ))
 		return;
 
 	if (unlikely(!fast_pool->mix.func))

From: Takashi Iwai <[email protected]>

commit c7807b27d510e5aa53c8a120cfc02c33c24ebb5f upstream.

Like the previous fix for Conexant codec, the beep_nid has to be set up before calling snd_hda_gen_parse_auto_config(); otherwise it'd miss the path setup.

Fix the call order for addressing the missing beep setup.

---
 sound/pci/hda/patch_via.c |    4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

@@ -520,11 +520,11 @@ static int via_parse_auto_config(struct
 	if (err < 0)
 		return err;
 
-	err = snd_hda_gen_parse_auto_config(codec, &spec->gen.autocfg);
+	err = auto_parse_beep(codec);
 	if (err < 0)
 		return err;
 
-	err = auto_parse_beep(codec);
+	err = snd_hda_gen_parse_auto_config(codec, &spec->gen.autocfg);
 	if (err < 0)
 		return err;
 

From: Takashi Iwai <[email protected]>

commit 5faa0bc69102f3a4c605581564c367be5eb94dfa upstream.

Currently the Conexant codec driver sets up the beep NID after calling snd_hda_gen_parse_auto_config(). It turned out that this results in the insufficient setup for the beep control, as the generic parser handles the fake path in snd_hda_gen_parse_auto_config() only if the beep_nid is set up beforehand.

For dealing with the beep widget properly, call cx_auto_parse_beep() before snd_hda_gen_parse_auto_config() call.

---
 sound/pci/hda/patch_conexant.c |    4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

@@ -1048,11 +1048,11 @@ static int patch_conexant_auto(struct hd
 	if (err < 0)
 		goto error;
 
-	err = snd_hda_gen_parse_auto_config(codec, &spec->gen.autocfg);
+	err = cx_auto_parse_beep(codec);
 	if (err < 0)
 		goto error;
 
-	err = cx_auto_parse_beep(codec);
+	err = snd_hda_gen_parse_auto_config(codec, &spec->gen.autocfg);
 	if (err < 0)
 		goto error;
 

From: Kailang Yang <[email protected]>

commit fe6900bd8156467365bd5b976df64928fdebfeb0 upstream.

There is not have Headset Mic verb table in BIOS default.
So, it will have recording issue from headset MIC.
Add the verb table value without jack detect. It will turn on Headset Mic.

---
 sound/pci/hda/patch_realtek.c |    9 +++++++++
 1 file changed, 9 insertions(+)

@@ -9805,6 +9805,7 @@ enum {
 	ALC668_FIXUP_MIC_DET_COEF,
 	ALC897_FIXUP_LENOVO_HEADSET_MIC,
 	ALC897_FIXUP_HEADSET_MIC_PIN,
+	ALC897_FIXUP_HP_HSMIC_VERB,
 };
 
 static const struct hda_fixup alc662_fixups[] = {

@@ -10224,6 +10225,13 @@ static const struct hda_fixup alc662_fix
 		.chained = true,
 		.chain_id = ALC897_FIXUP_LENOVO_HEADSET_MIC
 	},
+	[ALC897_FIXUP_HP_HSMIC_VERB] = {
+		.type = HDA_FIXUP_PINS,
+		.v.pins = (const struct hda_pintbl[]) {
+			{ 0x19, 0x01a1913c }, /* use as headset mic, without its own jack detect */
+			{ }
+		},
+	},
 };
 
 static const struct snd_pci_quirk alc662_fixup_tbl[] = {

@@ -10249,6 +10257,7 @@ static const struct snd_pci_quirk alc662
 	SND_PCI_QUIRK(0x1028, 0x0698, "Dell", ALC668_FIXUP_DELL_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x1028, 0x069f, "Dell", ALC668_FIXUP_DELL_MIC_NO_PRESENCE),
 	SND_PCI_QUIRK(0x103c, 0x1632, "HP RP5800", ALC662_FIXUP_HP_RP5800),
+	SND_PCI_QUIRK(0x103c, 0x8719, "HP", ALC897_FIXUP_HP_HSMIC_VERB),
 	SND_PCI_QUIRK(0x103c, 0x873e, "HP", ALC671_FIXUP_HP_HEADSET_MIC2),
 	SND_PCI_QUIRK(0x103c, 0x885f, "HP 288 Pro G8", ALC671_FIXUP_HP_HEADSET_MIC2),
 	SND_PCI_QUIRK(0x1043, 0x1080, "Asus UX501VW", ALC668_FIXUP_HEADSET_MODE),

From: Tim Crawford <[email protected]>

commit d49951219b0249d3eff49e4f02e0de82357bc8a0 upstream.

Fixes speaker output and headset detection on Clevo PD70PNT.

---
 sound/pci/hda/patch_realtek.c |    1 +
 1 file changed, 1 insertion(+)

@@ -2585,6 +2585,7 @@ static const struct snd_pci_quirk alc882
 	SND_PCI_QUIRK(0x1558, 0x67e1, "Clevo PB71[DE][CDF]", ALC1220_FIXUP_CLEVO_PB51ED_PINS),
 	SND_PCI_QUIRK(0x1558, 0x67e5, "Clevo PC70D[PRS](?:-D|-G)?", ALC1220_FIXUP_CLEVO_PB51ED_PINS),
 	SND_PCI_QUIRK(0x1558, 0x67f1, "Clevo PC70H[PRS]", ALC1220_FIXUP_CLEVO_PB51ED_PINS),
+	SND_PCI_QUIRK(0x1558, 0x67f5, "Clevo PD70PN[NRT]", ALC1220_FIXUP_CLEVO_PB51ED_PINS),
 	SND_PCI_QUIRK(0x1558, 0x70d1, "Clevo PC70[ER][CDF]", ALC1220_FIXUP_CLEVO_PB51ED_PINS),
 	SND_PCI_QUIRK(0x1558, 0x7714, "Clevo X170SM", ALC1220_FIXUP_CLEVO_PB51ED_PINS),
 	SND_PCI_QUIRK(0x1558, 0x7715, "Clevo X170KM-G", ALC1220_FIXUP_CLEVO_PB51ED),

From: Rosemarie O'Riorden <[email protected]>

commit 12378a5a75e33f34f8586706eb61cca9e6d4690c upstream.

When a packet enters the OVS datapath and does not match any existing flows installed in the kernel flow cache, the packet will be sent to userspace to be parsed, and a new flow will be created. The kernel and OVS rely on each other to parse packet fields in the same way so that packets will be handled properly.

As per the design document linked below, OVS expects all later IPv6 fragments to have nw_proto=44 in the flow key, so they can be correctly matched on OpenFlow rules. OpenFlow controllers create pipelines based on this design.

This behavior was changed by the commit in the Fixes tag so that nw_proto equals the next_header field of the last extension header. However, there is no counterpart for this change in OVS userspace, meaning that this field is parsed differently between OVS and the kernel. This is a problem because OVS creates actions based on what is parsed in userspace, but the kernel-provided flow key is used as a match criteria, as described in Documentation/networking/openvswitch.rst. This leads to issues such as packets incorrectly matching on a flow and thus the wrong list of actions being applied to the packet. Such changes in packet parsing cannot be implemented without breaking the userspace.

The offending commit is partially reverted to restore the expected behavior.

The change technically made sense and there is a good reason that it was implemented, but it does not comply with the original design of OVS. If in the future someone wants to implement such a change, then it must be user-configurable and disabled by default to preserve backwards compatibility with existing OVS versions.

---
 net/openvswitch/flow.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

@@ -265,7 +265,7 @@ static int parse_ipv6hdr(struct sk_buff
 	if (flags & IP6_FH_F_FRAG) {
 		if (frag_off) {
 			key->ip.frag = OVS_FRAG_TYPE_LATER;
-			key->ip.proto = nexthdr;
+			key->ip.proto = NEXTHDR_FRAGMENT;
 			return 0;
 		}
 		key->ip.frag = OVS_FRAG_TYPE_FIRST;

From: Chevron Li <[email protected]>

commit e591fcf6b4e39335c9b128b17738fcd2fdd278ae upstream.

The result from ->get_cd() may be incorrect as the card detect debouncing isn't managed correctly. Let's fix it.

---
 drivers/mmc/host/sdhci-pci-o2micro.c |    2 ++
 1 file changed, 2 insertions(+)

@@ -145,6 +145,8 @@ static int sdhci_o2_get_cd(struct mmc_ho
 
 	if (!(sdhci_readw(host, O2_PLL_DLL_WDT_CONTROL1) & O2_PLL_LOCK_STATUS))
 		sdhci_o2_enable_internal_clock(host);
+	else
+		sdhci_o2_wait_card_detect_stable(host);
 
 	return !!(sdhci_readl(host, SDHCI_PRESENT_STATE) & SDHCI_CARD_PRESENT);
 }

From: Sascha Hauer <[email protected]>

commit 06781a5026350cde699d2d10c9914a25c1524f45 upstream.

The DEVICE_BUSY_TIMEOUT value is described in the Reference Manual as:

| Timeout waiting for NAND Ready/Busy or ATA IRQ. Used in WAIT_FOR_READY | mode. This value is the number of GPMI_CLK cycles multiplied by 4096.

So instead of multiplying the value in cycles with 4096, we have to divide it by that value. Use DIV_ROUND_UP to make sure we are on the safe side, especially when the calculated value in cycles is smaller than 4096 as typically the case.

This bug likely never triggered because any timeout != 0 usually will do. In my case the busy timeout in cycles was originally calculated as 2408, which multiplied with 4096 is 0x968000. The lower 16 bits were taken for the 16 bit wide register field, so the register value was 0x8000. With 2970bf5a32f0 ("mtd: rawnand: gpmi: fix controller timings setting") however the value in cycles became 2384, which multiplied with 4096 is 0x950000. The lower 16 bit are 0x0 now resulting in an intermediate timeout when reading from NAND.

---
 drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

@@ -682,7 +682,7 @@ static void gpmi_nfc_compute_timings(str
 	hw->timing0 = BF_GPMI_TIMING0_ADDRESS_SETUP(addr_setup_cycles) |
 		      BF_GPMI_TIMING0_DATA_HOLD(data_hold_cycles) |
 		      BF_GPMI_TIMING0_DATA_SETUP(data_setup_cycles);
-	hw->timing1 = BF_GPMI_TIMING1_BUSY_TIMEOUT(busy_timeout_cycles * 4096);
+	hw->timing1 = BF_GPMI_TIMING1_BUSY_TIMEOUT(DIV_ROUND_UP(busy_timeout_cycles, 4096));
 
 	/*
 	 * Derive NFC ideal delay from {3}:

From: Edward Wu <[email protected]>

commit 540a92bfe6dab7310b9df2e488ba247d784d0163 upstream.

Add flags value to check the result of ata completion

---
 include/trace/events/libata.h |    1 +
 1 file changed, 1 insertion(+)

@@ -249,6 +249,7 @@ DECLARE_EVENT_CLASS(ata_qc_complete_temp
 		__entry->hob_feature	= qc->result_tf.hob_feature;
 		__entry->nsect		= qc->result_tf.nsect;
 		__entry->hob_nsect	= qc->result_tf.hob_nsect;
+		__entry->flags		= qc->flags;
 	),
 
 	TP_printk("ata_port=%u ata_dev=%u tag=%d flags=%s status=%s " \

From: Nikos Tsironis <[email protected]>

commit 9ae6e8b1c9bbf6874163d1243e393137313762b7 upstream.

During postsuspend dm-era does the following:

1. Archives the current era
2. Commits the metadata, as part of the RPC call for archiving the current era
3. Stops the worker

Until the worker stops, it might write to the metadata again. Moreover, these writes are not flushed to disk immediately, but are cached by the dm-bufio client, which writes them back asynchronously.

As a result, the committed metadata of a suspended dm-era device might not be consistent with the in-core metadata.

In some cases, this can result in the corruption of the on-disk metadata. Suppose the following sequence of events:

1. Load a new table, e.g. a snapshot-origin table, to a device with a dm-era table
2. Suspend the device
3. dm-era commits its metadata, but the worker does a few more metadata writes until it stops, as part of digesting an archived writeset
4. These writes are cached by the dm-bufio client
5. Load the dm-era table to another device.
6. The new instance of the dm-era target loads the committed, on-disk metadata, which don't include the extra writes done by the worker after the metadata commit.
7. Resume the new device
8. The new dm-era target instance starts using the metadata
9. Resume the original device
10. The destructor of the old dm-era target instance is called and destroys the dm-bufio client, which results in flushing the cached writes to disk
11. These writes might overwrite the writes done by the new dm-era instance, hence corrupting its metadata.

Fix this by committing the metadata after the worker stops running.

stop_worker uses flush_workqueue to flush the current work. However, the work item may re-queue itself and flush_workqueue doesn't wait for re-queued works to finish.

This could result in the worker changing the metadata after they have been committed, or writing to the metadata concurrently with the commit in the postsuspend thread.

Use drain_workqueue instead, which waits until the work and all re-queued works finish.

---
 drivers/md/dm-era-target.c |    8 +++++++-
 1 file changed, 7 insertions(+), 1 deletion(-)

@@ -1397,7 +1397,7 @@ static void start_worker(struct era *era
 static void stop_worker(struct era *era)
 {
 	atomic_set(&era->suspended, 1);
-	flush_workqueue(era->wq);
+	drain_workqueue(era->wq);
 }
 
 /*----------------------------------------------------------------

@@ -1581,6 +1581,12 @@ static void era_postsuspend(struct dm_ta
 	}
 
 	stop_worker(era);
+
+	r = metadata_commit(era->md);
+	if (r) {
+		DMERR("%s: metadata_commit failed", __func__);
+		/* FIXME: fail mode */
+	}
 }
 
 static int era_preresume(struct dm_target *ti)

From: Mikulas Patocka <[email protected]>

commit 90736eb3232d208ee048493f371075e4272e0944 upstream.

Commit 85e123c27d5c ("dm mirror log: round up region bitmap size to BITS_PER_LONG") introduced a regression on 64-bit architectures in the lvm testsuite tests: lvcreate-mirror, mirror-names and vgsplit-operation.

If the device is shrunk, we need to clear log bits beyond the end of the device. The code clears bits up to a 32-bit boundary and then calculates lc->sync_count by summing set bits up to a 64-bit boundary (the commit changed that; previously, this boundary was 32-bit too). So, it was using some non-zeroed bits in the calculation and this caused misbehavior.

Fix this regression by clearing bits up to BITS_PER_LONG boundary.

---
 drivers/md/dm-log.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

@@ -615,7 +615,7 @@ static int disk_resume(struct dm_dirty_l
 			log_clear_bit(lc, lc->clean_bits, i);
 
 	/* clear any old bits -- device has shrunk */
-	for (i = lc->region_count; i % (sizeof(*lc->clean_bits) << BYTE_SHIFT); i++)
+	for (i = lc->region_count; i % BITS_PER_LONG; i++)
 		log_clear_bit(lc, lc->clean_bits, i);
 
 	/* copy clean across to sync */

From: Jason A. Donenfeld <[email protected]>

commit c01d4d0a82b71857be7449380338bc53dde2da92 upstream.

random.c ratelimits how much it warns about uninitialized urandom reads using __ratelimit(). When the RNG is finally initialized, it prints the number of missed messages due to ratelimiting.

It has been this way since that functionality was introduced back in 2018. Recently, cc1e127bfa95 ("random: remove ratelimiting for in-kernel unseeded randomness") put a bit more stress on the urandom ratelimiting, which teased out a bug in the implementation.

Specifically, when under pressure, __ratelimit() will print its own message and reset the count back to 0, making the final message at the end less useful. Secondly, it does so as a pr_warn(), which apparently is undesirable for people's CI.

Fortunately, __ratelimit() has the RATELIMIT_MSG_ON_RELEASE flag exactly for this purpose, so we set the flag.

---
 drivers/char/random.c     |    2 +-
 include/linux/ratelimit.h |   12 ++++++++----
 2 files changed, 9 insertions(+), 5 deletions(-)

@@ -88,7 +88,7 @@ static RAW_NOTIFIER_HEAD(random_ready_ch
 
 /* Control how we warn userspace. */
 static struct ratelimit_state urandom_warning =
-	RATELIMIT_STATE_INIT("warn_urandom_randomness", HZ, 3);
+	RATELIMIT_STATE_INIT_FLAGS("urandom_warning", HZ, 3, RATELIMIT_MSG_ON_RELEASE);
 static int ratelimit_disable __read_mostly =
 	IS_ENABLED(CONFIG_WARN_ALL_UNSEEDED_RANDOM);
 module_param_named(ratelimit_disable, ratelimit_disable, int, 0644);

@@ -23,12 +23,16 @@ struct ratelimit_state {
 	unsigned long	flags;
 };
 
-#define RATELIMIT_STATE_INIT(name, interval_init, burst_init) {		\
-		.lock		= __RAW_SPIN_LOCK_UNLOCKED(name.lock),	\
-		.interval	= interval_init,			\
-		.burst		= burst_init,				\
+#define RATELIMIT_STATE_INIT_FLAGS(name, interval_init, burst_init, flags_init) { \
+		.lock		= __RAW_SPIN_LOCK_UNLOCKED(name.lock),		  \
+		.interval	= interval_init,				  \
+		.burst		= burst_init,					  \
+		.flags		= flags_init,					  \
 	}
 
+#define RATELIMIT_STATE_INIT(name, interval_init, burst_init) \
+	RATELIMIT_STATE_INIT_FLAGS(name, interval_init, burst_init, 0)
+
 #define RATELIMIT_STATE_INIT_DISABLED					\
 	RATELIMIT_STATE_INIT(ratelimit_state, 0, DEFAULT_RATELIMIT_BURST)
 

From: Carlo Lobrano <[email protected]>

commit 342fc0c3b345525da21112bd0478a0dc741598ea upstream.

Add support for the following Telit LE910Cx composition:

0x1250: rmnet, tty, tty, tty, tty

---
 drivers/usb/serial/option.c |    1 +
 1 file changed, 1 insertion(+)

@@ -1279,6 +1279,7 @@ static const struct usb_device_id option
 	  .driver_info = NCTRL(0) | RSVD(1) | RSVD(2) },
 	{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x1231, 0xff),	/* Telit LE910Cx (RNDIS) */
 	  .driver_info = NCTRL(2) | RSVD(3) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(TELIT_VENDOR_ID, 0x1250, 0xff, 0x00, 0x00) },	/* Telit LE910Cx (rmnet) */
 	{ USB_DEVICE(TELIT_VENDOR_ID, 0x1260),
 	  .driver_info = NCTRL(0) | RSVD(1) | RSVD(2) },
 	{ USB_DEVICE(TELIT_VENDOR_ID, 0x1261),

From: Yonglin Tan <[email protected]>

commit 33b29dbb39bcbd0a96e440646396bbf670b914fa upstream.

The EM05-G modem has 2 USB configurations that are configurable via the AT command AT+QCFG="usbnet",[ 0 | 2 ] which make the modem enumerate with the following interfaces, respectively:

"RMNET" : AT + DIAG + NMEA + Modem + QMI
"MBIM" : MBIM + AT + DIAG + NMEA + Modem

The detailed description of the USB configuration for each mode as follows:

RMNET Mode
--------------

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 21 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=2c7c ProdID=030a Rev= 3.18
S:  Manufacturer=Quectel
S:  Product=Quectel EM05-G
C:* #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=83(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=85(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=87(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=89(I) Atr=03(Int.) MxPS=   8 Ivl=32ms
E:  Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms

MBIM Mode
--------------

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 16 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=2c7c ProdID=030a Rev= 3.18
S:  Manufacturer=Quectel
S:  Product=Quectel EM05-G
C:* #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
A:  FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=83(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=85(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=87(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim
E:  Ad=89(I) Atr=03(Int.) MxPS=  64 Ivl=32ms
I:  If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E:  Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms

---
 drivers/usb/serial/option.c |    3 +++
 1 file changed, 3 insertions(+)

@@ -252,6 +252,7 @@ static void option_instat_callback(struc
 #define QUECTEL_PRODUCT_EG95			0x0195
 #define QUECTEL_PRODUCT_BG96			0x0296
 #define QUECTEL_PRODUCT_EP06			0x0306
+#define QUECTEL_PRODUCT_EM05G			0x030a
 #define QUECTEL_PRODUCT_EM12			0x0512
 #define QUECTEL_PRODUCT_RM500Q			0x0800
 #define QUECTEL_PRODUCT_EC200S_CN		0x6002

@@ -1134,6 +1135,8 @@ static const struct usb_device_id option
 	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EP06, 0xff, 0xff, 0xff),
 	  .driver_info = RSVD(1) | RSVD(2) | RSVD(3) | RSVD(4) | NUMEP2 },
 	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EP06, 0xff, 0, 0) },
+	{ USB_DEVICE_INTERFACE_CLASS(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM05G, 0xff),
+	  .driver_info = RSVD(6) | ZLP },
 	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM12, 0xff, 0xff, 0xff),
 	  .driver_info = RSVD(1) | RSVD(2) | RSVD(3) | RSVD(4) | NUMEP2 },
 	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM12, 0xff, 0, 0) },

From: Macpaul Lin <[email protected]>

commit 15b694e96c31807d8515aacfa687a1e8a4fbbadc upstream.

Add usb product id of the Quectel RM500K module.

RM500K provides 2 mandatory interfaces to Linux host after enumeration.
- /dev/ttyUSB5: this is a serial interface for control path. User needs to write AT commands to this device node to query status, set APN, set PIN code, and enable/disable the data connection to 5G network.
- ethX: this is the data path provided as a RNDIS devices. After the data connection has been established, Linux host can access 5G data network via this interface.

"RNDIS": RNDIS + ADB + AT (/dev/ttyUSB5) + MODEM COMs

usb-devices output for 0x7001:

T:  Bus=05 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  3 Spd=480 MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=2c7c ProdID=7001 Rev=00.01
S:  Manufacturer=MediaTek Inc.
S:  Product=USB DATA CARD
S:  SerialNumber=869206050009672
C:  #Ifs=10 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=02 Prot=ff Driver=rndis_host
E:  Ad=82(I) Atr=03(Int.) MxPS=  64 Ivl=125us
I:  If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 7 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 8 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=08(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 9 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=09(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

---
 drivers/usb/serial/option.c |    2 ++
 1 file changed, 2 insertions(+)

@@ -257,6 +257,7 @@ static void option_instat_callback(struc
 #define QUECTEL_PRODUCT_RM500Q			0x0800
 #define QUECTEL_PRODUCT_EC200S_CN		0x6002
 #define QUECTEL_PRODUCT_EC200T			0x6026
+#define QUECTEL_PRODUCT_RM500K			0x7001
 
 #define CMOTECH_VENDOR_ID			0x16d8
 #define CMOTECH_PRODUCT_6001			0x6001

@@ -1150,6 +1151,7 @@ static const struct usb_device_id option
 	  .driver_info = ZLP },
 	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EC200S_CN, 0xff, 0, 0) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EC200T, 0xff, 0, 0) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_RM500K, 0xff, 0x00, 0x00) },
 
 	{ USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_6001) },
 	{ USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_CMU_300) },

From: Jon Maxwell <[email protected]>

[ Upstream commit 3046a827316c0e55fc563b4fb78c93b9ca5c7c37 ]

A customer reported a request_socket leak in a Calico cloud environment. We found that a BPF program was doing a socket lookup with takes a refcnt on the socket and that it was finding the request_socket but returning the parent LISTEN socket via sk_to_full_sk() without decrementing the child request socket 1st, resulting in request_sock slab object leak. This patch retains the existing behaviour of returning full socks to the caller but it also decrements the child request_socket if one is present before doing so to prevent the leak.

Thanks to Curtis Taylor for all the help in diagnosing and testing this. And thanks to Antoine Tenart for the reproducer and patch input.

v2 of this patch contains, refactor as per Daniel Borkmann's suggestions to validate RCU flags on the listen socket so that it balances with bpf_sk_release() and update comments as per Martin KaFai Lau's suggestion. One small change to Daniels suggestion, put "sk = sk2" under "if (sk2 != sk)" to avoid an extra instruction.

---
 net/core/filter.c | 34 ++++++++++++++++++++++++++++------
 1 file changed, 28 insertions(+), 6 deletions(-)

index b0df4ddbe30c..eba96343c7af 100644
@@ -5313,10 +5313,21 @@ __bpf_sk_lookup(struct sk_buff *skb, struct bpf_sock_tuple *tuple, u32 len,
 					   ifindex, proto, netns_id, flags);
 
 	if (sk) {
-		sk = sk_to_full_sk(sk);
-		if (!sk_fullsock(sk)) {
+		struct sock *sk2 = sk_to_full_sk(sk);
+
+		/* sk_to_full_sk() may return (sk)->rsk_listener, so make sure the original sk
+		 * sock refcnt is decremented to prevent a request_sock leak.
+		 */
+		if (!sk_fullsock(sk2))
+			sk2 = NULL;
+		if (sk2 != sk) {
 			sock_gen_put(sk);
-			return NULL;
+			/* Ensure there is no need to bump sk2 refcnt */
+			if (unlikely(sk2 && !sock_flag(sk2, SOCK_RCU_FREE))) {
+				WARN_ONCE(1, "Found non-RCU, unreferenced socket!");
+				return NULL;
+			}
+			sk = sk2;
 		}
 	}
 

@@ -5350,10 +5361,21 @@ bpf_sk_lookup(struct sk_buff *skb, struct bpf_sock_tuple *tuple, u32 len,
 					 flags);
 
 	if (sk) {
-		sk = sk_to_full_sk(sk);
-		if (!sk_fullsock(sk)) {
+		struct sock *sk2 = sk_to_full_sk(sk);
+
+		/* sk_to_full_sk() may return (sk)->rsk_listener, so make sure the original sk
+		 * sock refcnt is decremented to prevent a request_sock leak.
+		 */
+		if (!sk_fullsock(sk2))
+			sk2 = NULL;
+		if (sk2 != sk) {
 			sock_gen_put(sk);
-			return NULL;
+			/* Ensure there is no need to bump sk2 refcnt */
+			if (unlikely(sk2 && !sock_flag(sk2, SOCK_RCU_FREE))) {
+				WARN_ONCE(1, "Found non-RCU, unreferenced socket!");
+				return NULL;
+			}
+			sk = sk2;
 		}
 	}
 

2.35.1

From: Claudiu Manoil <[email protected]>

[ Upstream commit 9b7fd1670a94a57d974795acebde843a5c1a354e ]

Even when the eth port is resticted to work with speeds not higher than 1G, and so the eth driver is requesting the phy (via phylink) to advertise up to 1000BASET support, the aquantia phy device is still advertising for 2.5G and 5G speeds.
Clear these advertising defaults when requested.

---
 drivers/net/phy/aquantia_main.c | 15 ++++++++++++++-
 1 file changed, 14 insertions(+), 1 deletion(-)

index 975789d9349d..75d8351ee250 100644
@@ -34,6 +34,8 @@
 #define MDIO_AN_VEND_PROV			0xc400
 #define MDIO_AN_VEND_PROV_1000BASET_FULL	BIT(15)
 #define MDIO_AN_VEND_PROV_1000BASET_HALF	BIT(14)
+#define MDIO_AN_VEND_PROV_5000BASET_FULL	BIT(11)
+#define MDIO_AN_VEND_PROV_2500BASET_FULL	BIT(10)
 #define MDIO_AN_VEND_PROV_DOWNSHIFT_EN		BIT(4)
 #define MDIO_AN_VEND_PROV_DOWNSHIFT_MASK	GENMASK(3, 0)
 #define MDIO_AN_VEND_PROV_DOWNSHIFT_DFLT	4

@@ -230,9 +232,20 @@ static int aqr_config_aneg(struct phy_device *phydev)
 			      phydev->advertising))
 		reg |= MDIO_AN_VEND_PROV_1000BASET_HALF;
 
+	/* Handle the case when the 2.5G and 5G speeds are not advertised */
+	if (linkmode_test_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT,
+			      phydev->advertising))
+		reg |= MDIO_AN_VEND_PROV_2500BASET_FULL;
+
+	if (linkmode_test_bit(ETHTOOL_LINK_MODE_5000baseT_Full_BIT,
+			      phydev->advertising))
+		reg |= MDIO_AN_VEND_PROV_5000BASET_FULL;
+
 	ret = phy_modify_mmd_changed(phydev, MDIO_MMD_AN, MDIO_AN_VEND_PROV,
 				     MDIO_AN_VEND_PROV_1000BASET_HALF |
-				     MDIO_AN_VEND_PROV_1000BASET_FULL, reg);
+				     MDIO_AN_VEND_PROV_1000BASET_FULL |
+				     MDIO_AN_VEND_PROV_2500BASET_FULL |
+				     MDIO_AN_VEND_PROV_5000BASET_FULL, reg);
 	if (ret < 0)
 		return ret;
 	if (ret > 0)

2.35.1

From: Jay Vosburgh <[email protected]>

[ Upstream commit 7a9214f3d88cfdb099f3896e102a306b316d8707 ]

The bonding ARP monitor fails to decrement send_peer_notif, the number of peer notifications (gratuitous ARP or ND) to be sent. This results in a continuous series of notifications.

Correct this by decrementing the counter for each notification.

---
 drivers/net/bonding/bond_main.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

index d6ecd03b6045..246bcbd650b4 100644
@@ -3071,9 +3071,11 @@ static void bond_activebackup_arp_mon(struct bonding *bond)
 		if (!rtnl_trylock())
 			return;
 
-		if (should_notify_peers)
+		if (should_notify_peers) {
+			bond->send_peer_notif--;
 			call_netdevice_notifiers(NETDEV_NOTIFY_PEERS,
 						 bond->dev);
+		}
 		if (should_notify_rtnl) {
 			bond_slave_state_notify(bond);
 			bond_slave_link_notify(bond);

2.35.1

From: Peilin Ye <[email protected]>

[ Upstream commit a2b1a5d40bd12b44322c2ccd40bb0ec1699708b6 ]

As reported by Yuming, currently tc always show a latency of UINT_MAX for netem Qdisc's on 32-bit platforms:

    $ tc qdisc add dev dummy0 root netem latency 100ms
    $ tc qdisc show dev dummy0
    qdisc netem 8001: root refcnt 2 limit 1000 delay 275s  275s
                                               ^^^^^^^^^^^^^^^^

Let us take a closer look at netem_dump():

        qopt.latency = min_t(psched_tdiff_t, PSCHED_NS2TICKS(q->latency,
                             UINT_MAX);

qopt.latency is __u32, psched_tdiff_t is signed long, (psched_tdiff_t)(UINT_MAX) is negative for 32-bit platforms, so qopt.latency is always UINT_MAX.

Fix it by using psched_time_t (u64) instead.

Note: confusingly, users have two ways to specify 'latency':

1. normally, via '__u32 latency' in struct tc_netem_qopt;
2. via the TCA_NETEM_LATENCY64 attribute, which is s64.

For the second case, theoretically 'latency' could be negative. This patch ignores that corner case, since it is broken (i.e. assigning a negative s64 to __u32) anyways, and should be handled separately.

Thanks Ted Lin for the analysis [1] .

[1] https://github.com/raspberrypi/linux/issues/3512

---
 net/sched/sch_netem.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

index f4101a920d1f..1802f134aa40 100644
@@ -1146,9 +1146,9 @@ static int netem_dump(struct Qdisc *sch, struct sk_buff *skb)
 	struct tc_netem_rate rate;
 	struct tc_netem_slot slot;
 
-	qopt.latency = min_t(psched_tdiff_t, PSCHED_NS2TICKS(q->latency),
+	qopt.latency = min_t(psched_time_t, PSCHED_NS2TICKS(q->latency),
 			     UINT_MAX);
-	qopt.jitter = min_t(psched_tdiff_t, PSCHED_NS2TICKS(q->jitter),
+	qopt.jitter = min_t(psched_time_t, PSCHED_NS2TICKS(q->jitter),
 			    UINT_MAX);
 	qopt.limit = q->limit;
 	qopt.loss = q->loss;

2.35.1

From: Miaoqian Lin <[email protected]>

[ Upstream commit b9cc4598607cb7f7eae5c75fc1e3209cd52ff5e0 ]

of_graph_get_remote_node() returns remote device node pointer with refcount incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.

Patchwork: https://patchwork.freedesktop.org/patch/488473/

---
 drivers/gpu/drm/msm/disp/mdp4/mdp4_kms.c | 2 ++
 1 file changed, 2 insertions(+)

index 4f0c6d58e06f..f0a5767b69f5 100644
@@ -245,6 +245,7 @@ static int mdp4_modeset_init_intf(struct mdp4_kms *mdp4_kms,
 		encoder = mdp4_lcdc_encoder_init(dev, panel_node);
 		if (IS_ERR(encoder)) {
 			DRM_DEV_ERROR(dev->dev, "failed to construct LCDC encoder\n");
+			of_node_put(panel_node);
 			return PTR_ERR(encoder);
 		}
 

@@ -254,6 +255,7 @@ static int mdp4_modeset_init_intf(struct mdp4_kms *mdp4_kms,
 		connector = mdp4_lvds_connector_init(dev, panel_node, encoder);
 		if (IS_ERR(connector)) {
 			DRM_DEV_ERROR(dev->dev, "failed to initialize LVDS connector\n");
+			of_node_put(panel_node);
 			return PTR_ERR(connector);
 		}
 

2.35.1

From: Eric Dumazet <[email protected]>

[ Upstream commit 301bd140ed0b24f0da660874c7e8a47dad8c8222 ]

Rewrite tests in ip6erspan_tunnel_xmit() and erspan_fb_xmit() to not assume transport header is set.

syzbot reported:

WARNING: CPU: 0 PID: 1350 at include/linux/skbuff.h:2911 skb_transport_header include/linux/skbuff.h:2911 [inline]
WARNING: CPU: 0 PID: 1350 at include/linux/skbuff.h:2911 ip6erspan_tunnel_xmit+0x15af/0x2eb0 net/ipv6/ip6_gre.c:963
Modules linked in:
CPU: 0 PID: 1350 Comm: aoe_tx0 Not tainted 5.19.0-rc2-syzkaller-00160-g274295c6e53f #0
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.14.0-2 04/01/2014
RIP: 0010:skb_transport_header include/linux/skbuff.h:2911 [inline]
RIP: 0010:ip6erspan_tunnel_xmit+0x15af/0x2eb0 net/ipv6/ip6_gre.c:963
Code: 0f 47 f0 40 88 b5 7f fe ff ff e8 8c 16 4b f9 89 de bf ff ff ff ff e8 a0 12 4b f9 66 83 fb ff 0f 85 1d f1 ff ff e8 71 16 4b f9 <0f> 0b e9 43 f0 ff ff e8 65 16 4b f9 48 8d 85 30 ff ff ff ba 60 00
RSP: 0018:ffffc90005daf910 EFLAGS: 00010293
RAX: 0000000000000000 RBX: 000000000000ffff RCX: 0000000000000000
RDX: ffff88801f032100 RSI: ffffffff882e8d3f RDI: 0000000000000003
RBP: ffffc90005dafab8 R08: 0000000000000003 R09: 000000000000ffff
R10: 000000000000ffff R11: 0000000000000000 R12: ffff888024f21d40
R13: 000000000000a288 R14: 00000000000000b0 R15: ffff888025a2e000
FS: 0000000000000000(0000) GS:ffff88802c800000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000001b2e425000 CR3: 000000006d099000 CR4: 0000000000152ef0
Call Trace:
<TASK>
__netdev_start_xmit include/linux/netdevice.h:4805 [inline]
netdev_start_xmit include/linux/netdevice.h:4819 [inline]
xmit_one net/core/dev.c:3588 [inline]
dev_hard_start_xmit+0x188/0x880 net/core/dev.c:3604
sch_direct_xmit+0x19f/0xbe0 net/sched/sch_generic.c:342
__dev_xmit_skb net/core/dev.c:3815 [inline]
__dev_queue_xmit+0x14a1/0x3900 net/core/dev.c:4219
dev_queue_xmit include/linux/netdevice.h:2994 [inline]
tx+0x6a/0xc0 drivers/block/aoe/aoenet.c:63
kthread+0x1e7/0x3b0 drivers/block/aoe/aoecmd.c:1229
kthread+0x2e9/0x3a0 kernel/kthread.c:376
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:302
</TASK>

---
 net/ipv4/ip_gre.c  | 15 ++++++++++-----
 net/ipv6/ip6_gre.c | 15 ++++++++++-----
 2 files changed, 20 insertions(+), 10 deletions(-)

index 614410a6db44..52dbffb7bc2f 100644
@@ -497,7 +497,6 @@ static void erspan_fb_xmit(struct sk_buff *skb, struct net_device *dev)
 	int tunnel_hlen;
 	int version;
 	int nhoff;
-	int thoff;
 
 	tun_info = skb_tunnel_info(skb);
 	if (unlikely(!tun_info || !(tun_info->mode & IP_TUNNEL_INFO_TX) ||

@@ -531,10 +530,16 @@ static void erspan_fb_xmit(struct sk_buff *skb, struct net_device *dev)
 	    (ntohs(ip_hdr(skb)->tot_len) > skb->len - nhoff))
 		truncate = true;
 
-	thoff = skb_transport_header(skb) - skb_mac_header(skb);
-	if (skb->protocol == htons(ETH_P_IPV6) &&
-	    (ntohs(ipv6_hdr(skb)->payload_len) > skb->len - thoff))
-		truncate = true;
+	if (skb->protocol == htons(ETH_P_IPV6)) {
+		int thoff;
+
+		if (skb_transport_header_was_set(skb))
+			thoff = skb_transport_header(skb) - skb_mac_header(skb);
+		else
+			thoff = nhoff + sizeof(struct ipv6hdr);
+		if (ntohs(ipv6_hdr(skb)->payload_len) > skb->len - thoff)
+			truncate = true;
+	}
 
 	if (version == 1) {
 		erspan_build_header(skb, ntohl(tunnel_id_to_key32(key->tun_id)),

index e550db28aabb..4a6396d574a0 100644
@@ -927,7 +927,6 @@ static netdev_tx_t ip6erspan_tunnel_xmit(struct sk_buff *skb,
 	__be16 proto;
 	__u32 mtu;
 	int nhoff;
-	int thoff;
 
 	if (!pskb_inet_may_pull(skb))
 		goto tx_err;

@@ -948,10 +947,16 @@ static netdev_tx_t ip6erspan_tunnel_xmit(struct sk_buff *skb,
 	    (ntohs(ip_hdr(skb)->tot_len) > skb->len - nhoff))
 		truncate = true;
 
-	thoff = skb_transport_header(skb) - skb_mac_header(skb);
-	if (skb->protocol == htons(ETH_P_IPV6) &&
-	    (ntohs(ipv6_hdr(skb)->payload_len) > skb->len - thoff))
-		truncate = true;
+	if (skb->protocol == htons(ETH_P_IPV6)) {
+		int thoff;
+
+		if (skb_transport_header_was_set(skb))
+			thoff = skb_transport_header(skb) - skb_mac_header(skb);
+		else
+			thoff = nhoff + sizeof(struct ipv6hdr);
+		if (ntohs(ipv6_hdr(skb)->payload_len) > skb->len - thoff)
+			truncate = true;
+	}
 
 	if (skb_cow_head(skb, dev->needed_headroom ?: t->hlen))
 		goto tx_err;

2.35.1

From: Ziyang Xuan <[email protected]>

[ Upstream commit 69135c572d1f84261a6de2a1268513a7e71753e2 ]

After setting the sock ktls, update ctx->sk_proto to sock->sk_prot by tls_update(), so now ctx->sk_proto->close is tls_sk_proto_close(). When close the sock, tls_sk_proto_close() is called for sock->sk_prot->close is tls_sk_proto_close(). But ctx->sk_proto->close() will be executed later in tls_sk_proto_close(). Thus tls_sk_proto_close() executed repeatedly occurred. That will trigger the following bug.

=================================================================

KASAN: null-ptr-deref in range [0x0000000000000010-0x0000000000000017]
RIP: 0010:tls_sk_proto_close+0xd8/0xaf0 net/tls/tls_main.c:306
Call Trace:
 <TASK>
 tls_sk_proto_close+0x356/0xaf0 net/tls/tls_main.c:329
 inet_release+0x12e/0x280 net/ipv4/af_inet.c:428
 __sock_release+0xcd/0x280 net/socket.c:650
 sock_close+0x18/0x20 net/socket.c:1365

Updating a proto which is same with sock->sk_prot is incorrect. Add proto and sock->sk_prot equality check at the head of tls_update() to fix it.

---
 net/tls/tls_main.c | 3 +++
 1 file changed, 3 insertions(+)

index 7aba4ee77aba..df9177d96f7f 100644
@@ -803,6 +803,9 @@ static void tls_update(struct sock *sk, struct proto *p,
 {
 	struct tls_context *ctx;
 
+	if (sk->sk_prot == p)
+		return;
+
 	ctx = tls_get_ctx(sk);
 	if (likely(ctx)) {
 		ctx->sk_write_space = write_space;

2.35.1

From: Gerd Hoffmann <[email protected]>

[ Upstream commit 05b252cccb2e5c3f56119d25de684b4f810ba40a ]

Check vm_fault->pgoff before using it. When we removed the warning, we also removed the check.

---
 drivers/dma-buf/udmabuf.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)

index e553c6a937f6..c6e9b7bd7618 100644
@@ -24,8 +24,11 @@ static vm_fault_t udmabuf_vm_fault(struct vm_fault *vmf)
 {
 	struct vm_area_struct *vma = vmf->vma;
 	struct udmabuf *ubuf = vma->vm_private_data;
+	pgoff_t pgoff = vmf->pgoff;
 
-	vmf->page = ubuf->pages[vmf->pgoff];
+	if (pgoff >= ubuf->pagecount)
+		return VM_FAULT_SIGBUS;
+	vmf->page = ubuf->pages[pgoff];
 	get_page(vmf->page);
 	return 0;
 }

2.35.1

From: Julien Grall <[email protected]>

[ Upstream commit ecb6237fa397b7b810d798ad19322eca466dbab1 ]

1 << 31 is undefined. So switch to 1U << 31.

---
 drivers/xen/features.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

index 25c053b09605..2c306de228db 100644
@@ -29,6 +29,6 @@ void xen_setup_features(void)
 		if (HYPERVISOR_xen_version(XENVER_get_features, &fi) < 0)
 			break;
 		for (j = 0; j < 32; j++)
-			xen_features[i * 32 + j] = !!(fi.submap & 1<<j);
+			xen_features[i * 32 + j] = !!(fi.submap & 1U << j);
 	}
 }

2.35.1

From: huhai <[email protected]>

[ Upstream commit c81aba8fde2aee4f5778ebab3a1d51bd2ef48e4c ]

commit 979934da9e7a ("[PATCH] mips: update IRQ handling for vr41xx") added a function irq_dispatch, and it'll increase irq_err_count when the get_irq callback returns a negative value, but increase irq_err_count in get_irq was not removed.

And also, modpost complains once gpio-vr41xx drivers become modules.
ERROR: modpost: "irq_err_count" [drivers/gpio/gpio-vr41xx.ko] undefined!

So it would be a good idea to remove repetitive increase irq_err_count in get_irq callback.

---
 arch/mips/vr41xx/common/icu.c | 2 --
 drivers/gpio/gpio-vr41xx.c    | 2 --
 2 files changed, 4 deletions(-)

index 7b7f25b4b057..9240bcdbe74e 100644
@@ -640,8 +640,6 @@ static int icu_get_irq(unsigned int irq)
 
 	printk(KERN_ERR "spurious ICU interrupt: %04x,%04x\n", pend1, pend2);
 
-	atomic_inc(&irq_err_count);
-
 	return -1;
 }
 

index 98cd715ccc33..8d09b619c166 100644
@@ -217,8 +217,6 @@ static int giu_get_irq(unsigned int irq)
 	printk(KERN_ERR "spurious GIU interrupt: %04x(%04x),%04x(%04x)\n",
 	       maskl, pendl, maskh, pendh);
 
-	atomic_inc(&irq_err_count);
-
 	return -EINVAL;
 }
 

2.35.1

From: David Howells <[email protected]>

[ Upstream commit cb78d1b5efffe4cf97e16766329dd7358aed3deb ]

The recent patch to make afs_getattr consult the server didn't account for the pseudo-inodes employed by the dynamic root-type afs superblock not having a volume or a server to access, and thus an oops occurs if such a directory is stat'd.

Fix this by checking to see if the vnode->volume pointer actually points anywhere before following it in afs_getattr().

This can be tested by stat'ing a directory in /afs. It may be sufficient just to do "ls /afs" and the oops looks something like:

        BUG: kernel NULL pointer dereference, address: 0000000000000020
        ...
        RIP: 0010:afs_getattr+0x8b/0x14b
        ...
        Call Trace:
         <TASK>
         vfs_statx+0x79/0xf5
         vfs_fstatat+0x49/0x62

---
 fs/afs/inode.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

index 90eac3ec01cb..622363af4c1b 100644
@@ -739,7 +739,8 @@ int afs_getattr(const struct path *path, struct kstat *stat,
 
 	_enter("{ ino=%lu v=%u }", inode->i_ino, inode->i_generation);
 
-	if (!(query_flags & AT_STATX_DONT_SYNC) &&
+	if (vnode->volume &&
+	    !(query_flags & AT_STATX_DONT_SYNC) &&
 	    !test_bit(AFS_VNODE_CB_PROMISED, &vnode->flags)) {
 		key = afs_request_key(vnode->volume->cell);
 		if (IS_ERR(key))

2.35.1

From: Anatolii Gerasymenko <[email protected]>

[ Upstream commit c3d184c83ff4b80167e34edfc3d21df424bf27ff ]

In current implementation ice_update_phy_type enables all link modes for selected speed. This approach doesn't work for 1000M speeds, because both copper (1000baseT) and optical (1000baseX) standards cannot be enabled at once.

Fix this, by adding the function ice_set_phy_type_from_speed() for 1000M speeds.

---
 drivers/net/ethernet/intel/ice/ice_ethtool.c | 39 +++++++++++++++++++-
 1 file changed, 38 insertions(+), 1 deletion(-)

index fc9ff985a62b..b297a3ca22fc 100644
@@ -2337,6 +2337,42 @@ ice_setup_autoneg(struct ice_port_info *p, struct ethtool_link_ksettings *ks,
 	return err;
 }
 
+/**
+ * ice_set_phy_type_from_speed - set phy_types based on speeds
+ * and advertised modes
+ * @ks: ethtool link ksettings struct
+ * @phy_type_low: pointer to the lower part of phy_type
+ * @phy_type_high: pointer to the higher part of phy_type
+ * @adv_link_speed: targeted link speeds bitmap
+ */
+static void
+ice_set_phy_type_from_speed(const struct ethtool_link_ksettings *ks,
+			    u64 *phy_type_low, u64 *phy_type_high,
+			    u16 adv_link_speed)
+{
+	/* Handle 1000M speed in a special way because ice_update_phy_type
+	 * enables all link modes, but having mixed copper and optical
+	 * standards is not supported.
+	 */
+	adv_link_speed &= ~ICE_AQ_LINK_SPEED_1000MB;
+
+	if (ethtool_link_ksettings_test_link_mode(ks, advertising,
+						  1000baseT_Full))
+		*phy_type_low |= ICE_PHY_TYPE_LOW_1000BASE_T |
+				 ICE_PHY_TYPE_LOW_1G_SGMII;
+
+	if (ethtool_link_ksettings_test_link_mode(ks, advertising,
+						  1000baseKX_Full))
+		*phy_type_low |= ICE_PHY_TYPE_LOW_1000BASE_KX;
+
+	if (ethtool_link_ksettings_test_link_mode(ks, advertising,
+						  1000baseX_Full))
+		*phy_type_low |= ICE_PHY_TYPE_LOW_1000BASE_SX |
+				 ICE_PHY_TYPE_LOW_1000BASE_LX;
+
+	ice_update_phy_type(phy_type_low, phy_type_high, adv_link_speed);
+}
+
 /**
  * ice_set_link_ksettings - Set Speed and Duplex
  * @netdev: network interface device structure

@@ -2472,7 +2508,8 @@ ice_set_link_ksettings(struct net_device *netdev,
 		adv_link_speed = curr_link_speed;
 
 	/* Convert the advertise link speeds to their corresponded PHY_TYPE */
-	ice_update_phy_type(&phy_type_low, &phy_type_high, adv_link_speed);
+	ice_set_phy_type_from_speed(ks, &phy_type_low, &phy_type_high,
+				    adv_link_speed);
 
 	if (!autoneg_changed && adv_link_speed == curr_link_speed) {
 		netdev_info(netdev, "Nothing changed, exiting without setting anything.\n");

2.35.1

From: Aidan MacDonald <[email protected]>

[ Upstream commit 485037ae9a095491beb7f893c909a76cc4f9d1e7 ]

When enabling a type_in_mask irq, the type_buf contents must be AND'd with the mask of the IRQ we're enabling to avoid enabling other IRQs by accident, which can happen if several type_in_mask irqs share a mask register.

---
 drivers/base/regmap/regmap-irq.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

index 3d64c9331a82..3c1e554df4eb 100644
@@ -214,6 +214,7 @@ static void regmap_irq_enable(struct irq_data *data)
 	struct regmap_irq_chip_data *d = irq_data_get_irq_chip_data(data);
 	struct regmap *map = d->map;
 	const struct regmap_irq *irq_data = irq_to_regmap_irq(d, data->hwirq);
+	unsigned int reg = irq_data->reg_offset / map->reg_stride;
 	unsigned int mask, type;
 
 	type = irq_data->type.type_falling_val | irq_data->type.type_rising_val;

@@ -230,14 +231,14 @@ static void regmap_irq_enable(struct irq_data *data)
 	 * at the corresponding offset in regmap_irq_set_type().
 	 */
 	if (d->chip->type_in_mask && type)
-		mask = d->type_buf[irq_data->reg_offset / map->reg_stride];
+		mask = d->type_buf[reg] & irq_data->mask;
 	else
 		mask = irq_data->mask;
 
 	if (d->chip->clear_on_unmask)
 		d->clear_status = true;
 
-	d->mask_buf[irq_data->reg_offset / map->reg_stride] &= ~mask;
+	d->mask_buf[reg] &= ~mask;
 }
 
 static void regmap_irq_disable(struct irq_data *data)

2.35.1

From: Kai-Heng Feng <[email protected]>

[ Upstream commit 4e0effd9007ea0be31f7488611eb3824b4541554 ]

Intel I210 on some Intel Alder Lake platforms can only achieve ~750Mbps Tx speed via iperf. The RR2DCDELAY shows around 0x2xxx DMA delay, which will be significantly lower when 1) ASPM is disabled or 2) SoC package c-state stays above PC3. When the RR2DCDELAY is around 0x1xxx the Tx speed can reach to ~950Mbps.

According to the I210 datasheet "8.26.1 PCIe Misc. Register - PCIEMISC", "DMA Idle Indication" doesn't seem to tie to DMA coalesce anymore, so set it to 1b for "DMA is considered idle when there is no Rx or Tx AND when there are no TLPs indicating that CPU is active detected on the PCIe link (such as the host executes CSR or Configuration register read or write operation)" and performing Tx should also fall under "active CPU on PCIe link" case.

In addition to that, commit b6e0c419f040 ("igb: Move DMA Coalescing init code to separate function.") seems to wrongly changed from enabling E1000_PCIEMISC_LX_DECISION to disabling it, also fix that.

---
 drivers/net/ethernet/intel/igb/igb_main.c | 12 +++++-------
 1 file changed, 5 insertions(+), 7 deletions(-)

index 26c8d09ad4dd..8734dfd001bb 100644
@@ -9404,11 +9404,10 @@ static void igb_init_dmac(struct igb_adapter *adapter, u32 pba)
 	struct e1000_hw *hw = &adapter->hw;
 	u32 dmac_thr;
 	u16 hwm;
+	u32 reg;
 
 	if (hw->mac.type > e1000_82580) {
 		if (adapter->flags & IGB_FLAG_DMAC) {
-			u32 reg;
-
 			/* force threshold to 0. */
 			wr32(E1000_DMCTXTH, 0);
 

@@ -9441,7 +9440,6 @@ static void igb_init_dmac(struct igb_adapter *adapter, u32 pba)
 			/* Disable BMC-to-OS Watchdog Enable */
 			if (hw->mac.type != e1000_i354)
 				reg &= ~E1000_DMACR_DC_BMC2OSW_EN;
-
 			wr32(E1000_DMACR, reg);
 
 			/* no lower threshold to disable

@@ -9458,12 +9456,12 @@ static void igb_init_dmac(struct igb_adapter *adapter, u32 pba)
 			 */
 			wr32(E1000_DMCTXTH, (IGB_MIN_TXPBSIZE -
 			     (IGB_TX_BUF_4096 + adapter->max_frame_size)) >> 6);
+		}
 
-			/* make low power state decision controlled
-			 * by DMA coal
-			 */
+		if (hw->mac.type >= e1000_i210 ||
+		    (adapter->flags & IGB_FLAG_DMAC)) {
 			reg = rd32(E1000_PCIEMISC);
-			reg &= ~E1000_PCIEMISC_LX_DECISION;
+			reg |= E1000_PCIEMISC_LX_DECISION;
 			wr32(E1000_PCIEMISC, reg);
 		} /* endif adapter->dmac is not disabled */
 	} else if (hw->mac.type == e1000_82580) {

2.35.1

From: Stephan Gerhold <[email protected]>

[ Upstream commit 8af52fe9fd3bf5e7478da99193c0632276e1dfce ]

The following sequence currently causes a driver bug warning when using virtio_net:

  # ip link set eth0 up
  # echo mem > /sys/power/state (or e.g. # rtcwake -s 10 -m mem)
  <resume>
  # ip link set eth0 down

Missing register, driver bug

  WARNING: CPU: 0 PID: 375 at net/core/xdp.c:138 xdp_rxq_info_unreg+0x58/0x60
  Call trace:
   xdp_rxq_info_unreg+0x58/0x60
   virtnet_close+0x58/0xac
   __dev_close_many+0xac/0x140
   __dev_change_flags+0xd8/0x210
   dev_change_flags+0x24/0x64
   do_setlink+0x230/0xdd0
   ...

This happens because virtnet_freeze() frees the receive_queue completely (including struct xdp_rxq_info) but does not call xdp_rxq_info_unreg(). Similarly, virtnet_restore() sets up the receive_queue again but does not call xdp_rxq_info_reg().

Actually, parts of virtnet_freeze_down() and virtnet_restore_up() are almost identical to virtnet_close() and virtnet_open(): only the calls to xdp_rxq_info_(un)reg() are missing. This means that we can fix this easily and avoid such problems in the future by just calling virtnet_close()/open() from the freeze/restore handlers.

Aside from adding the missing xdp_rxq_info calls the only difference is that the refill work is only cancelled if netif_running(). However, this should not make any functional difference since the refill work should only be active if the network interface is actually up.

---
 drivers/net/virtio_net.c | 25 ++++++-------------------
 1 file changed, 6 insertions(+), 19 deletions(-)

index 37c2cecd1e50..f4c03518d7d2 100644
@@ -2393,7 +2393,6 @@ static const struct ethtool_ops virtnet_ethtool_ops = {
 static void virtnet_freeze_down(struct virtio_device *vdev)
 {
 	struct virtnet_info *vi = vdev->priv;
-	int i;
 
 	/* Make sure no work handler is accessing the device */
 	flush_work(&vi->config_work);

@@ -2401,14 +2400,8 @@ static void virtnet_freeze_down(struct virtio_device *vdev)
 	netif_tx_lock_bh(vi->dev);
 	netif_device_detach(vi->dev);
 	netif_tx_unlock_bh(vi->dev);
-	cancel_delayed_work_sync(&vi->refill);
-
-	if (netif_running(vi->dev)) {
-		for (i = 0; i < vi->max_queue_pairs; i++) {
-			napi_disable(&vi->rq[i].napi);
-			virtnet_napi_tx_disable(&vi->sq[i].napi);
-		}
-	}
+	if (netif_running(vi->dev))
+		virtnet_close(vi->dev);
 }
 
 static int init_vqs(struct virtnet_info *vi);

@@ -2416,7 +2409,7 @@ static int init_vqs(struct virtnet_info *vi);
 static int virtnet_restore_up(struct virtio_device *vdev)
 {
 	struct virtnet_info *vi = vdev->priv;
-	int err, i;
+	int err;
 
 	err = init_vqs(vi);
 	if (err)

@@ -2425,15 +2418,9 @@ static int virtnet_restore_up(struct virtio_device *vdev)
 	virtio_device_ready(vdev);
 
 	if (netif_running(vi->dev)) {
-		for (i = 0; i < vi->curr_queue_pairs; i++)
-			if (!try_fill_recv(vi, &vi->rq[i], GFP_KERNEL))
-				schedule_delayed_work(&vi->refill, 0);
-
-		for (i = 0; i < vi->max_queue_pairs; i++) {
-			virtnet_napi_enable(vi->rq[i].vq, &vi->rq[i].napi);
-			virtnet_napi_tx_enable(vi, vi->sq[i].vq,
-					       &vi->sq[i].napi);
-		}
+		err = virtnet_open(vi->dev);
+		if (err)
+			return err;
 	}
 
 	netif_tx_lock_bh(vi->dev);

2.35.1

From: Jakub Kicinski <[email protected]>

[ Upstream commit 1b205d948fbb06a7613d87dcea0ff5fd8a08ed91 ]

This reverts commit 69135c572d1f84261a6de2a1268513a7e71753e2.

This commit was just papering over the issue, ULP should not get ->update() called with its own sk_prot. Each ULP would need to add this check.

---
 net/tls/tls_main.c | 3 ---
 1 file changed, 3 deletions(-)

index df9177d96f7f..7aba4ee77aba 100644
@@ -803,9 +803,6 @@ static void tls_update(struct sock *sk, struct proto *p,
 {
 	struct tls_context *ctx;
 
-	if (sk->sk_prot == p)
-		return;
-
 	ctx = tls_get_ctx(sk);
 	if (likely(ctx)) {
 		ctx->sk_write_space = write_space;

2.35.1

From: Dan Carpenter <[email protected]>

[ Upstream commit 9ca766eaea2e87b8b773bff04ee56c055cb76d4e ]

This error path returns 1, but it should instead propagate the negative error code from winbond_sio_enter().

---
 drivers/gpio/gpio-winbond.c | 7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)

index 7f8f5b02e31d..4b61d975cc0e 100644
@@ -385,12 +385,13 @@ static int winbond_gpio_get(struct gpio_chip *gc, unsigned int offset)
 	unsigned long *base = gpiochip_get_data(gc);
 	const struct winbond_gpio_info *info;
 	bool val;
+	int ret;
 
 	winbond_gpio_get_info(&offset, &info);
 
-	val = winbond_sio_enter(*base);
-	if (val)
-		return val;
+	ret = winbond_sio_enter(*base);
+	if (ret)
+		return ret;
 
 	winbond_sio_select_logical(*base, info->dev);
 

2.35.1

From: Thomas Richter <[email protected]>

[ Upstream commit be857b7f77d130dbbd47c91fc35198b040f35865 ]

Events CPU_CYCLES and INSTRUCTIONS can be submitted with two different perf_event attribute::type values:
- PERF_TYPE_HARDWARE: when invoked via perf tool predefined events name cycles or cpu-cycles or instructions.
- pmu->type: when invoked via perf tool event name cpu_cf/CPU_CYLCES/ or cpu_cf/INSTRUCTIONS/. This invocation also selects the PMU to which the event belongs.
Handle both type of invocations identical for events CPU_CYLCES and INSTRUCTIONS. They address the same hardware.
The result is different when event modifier exclude_kernel is also set. Invocation with event modifier for user space event counting fails.

Output before:

 # perf stat -e cpum_cf/cpu_cycles/u -- true

Performance counter stats for 'true':

<not supported> cpum_cf/cpu_cycles/u

       0.000761033 seconds time elapsed

       0.000076000 seconds user
       0.000725000 seconds sys

#

Output after:

 # perf stat -e cpum_cf/cpu_cycles/u -- true

Performance counter stats for 'true':

           349,613      cpum_cf/cpu_cycles/u

       0.000844143 seconds time elapsed

       0.000079000 seconds user
       0.000800000 seconds sys

#

---
 arch/s390/kernel/perf_cpum_cf.c | 22 +++++++++++++++++++++-
 1 file changed, 21 insertions(+), 1 deletion(-)

index 0eb1d1cc53a8..dddb32e53db8 100644
@@ -292,6 +292,26 @@ static int __hw_perf_event_init(struct perf_event *event, unsigned int type)
 	return err;
 }
 
+/* Events CPU_CYLCES and INSTRUCTIONS can be submitted with two different
+ * attribute::type values:
+ * - PERF_TYPE_HARDWARE:
+ * - pmu->type:
+ * Handle both type of invocations identical. They address the same hardware.
+ * The result is different when event modifiers exclude_kernel and/or
+ * exclude_user are also set.
+ */
+static int cpumf_pmu_event_type(struct perf_event *event)
+{
+	u64 ev = event->attr.config;
+
+	if (cpumf_generic_events_basic[PERF_COUNT_HW_CPU_CYCLES] == ev ||
+	    cpumf_generic_events_basic[PERF_COUNT_HW_INSTRUCTIONS] == ev ||
+	    cpumf_generic_events_user[PERF_COUNT_HW_CPU_CYCLES] == ev ||
+	    cpumf_generic_events_user[PERF_COUNT_HW_INSTRUCTIONS] == ev)
+		return PERF_TYPE_HARDWARE;
+	return PERF_TYPE_RAW;
+}
+
 static int cpumf_pmu_event_init(struct perf_event *event)
 {
 	unsigned int type = event->attr.type;

@@ -301,7 +321,7 @@ static int cpumf_pmu_event_init(struct perf_event *event)
 		err = __hw_perf_event_init(event, type);
 	else if (event->pmu->type == type)
 		/* Registered as unknown PMU */
-		err = __hw_perf_event_init(event, PERF_TYPE_RAW);
+		err = __hw_perf_event_init(event, cpumf_pmu_event_type(event));
 	else
 		return -ENOENT;
 

2.35.1

From: Baruch Siach <[email protected]>

[ Upstream commit f1a633b15cd5371a2a83f02c513984e51132dd68 ]

The documentation missed the "in_" prefix for this IIO_SHARED_BY_DIR entry.

---
 Documentation/ABI/testing/sysfs-bus-iio-vf610 | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

index 308a6756d3bf..491ead804488 100644
@@ -1,4 +1,4 @@
-What:		/sys/bus/iio/devices/iio:deviceX/conversion_mode
+What:		/sys/bus/iio/devices/iio:deviceX/in_conversion_mode
 KernelVersion:	4.2
 Contact:	[email protected]
 Description:

2.35.1

From: Mathias Nyman <[email protected]>

commit 83810f84ecf11dfc5a9414a8b762c3501b328185 upstream.

If ports are not turned off in shutdown then runtime suspended self-powered USB devices may survive in U3 link state over S5.

During subsequent boot, if firmware sends an IPC command to program the port in DISCONNECT state, it will time out, causing significant delay in the boot time.

Turning off roothub port power is also recommended in xhci specification 4.19.4 "Port Power" in the additional note.

---
 drivers/usb/host/xhci-hub.c |    2 +-
 drivers/usb/host/xhci.c     |   15 +++++++++++++--
 drivers/usb/host/xhci.h     |    2 ++
 3 files changed, 16 insertions(+), 3 deletions(-)

@@ -566,7 +566,7 @@ struct xhci_hub *xhci_get_rhub(struct us
  * It will release and re-aquire the lock while calling ACPI
  * method.
  */
-static void xhci_set_port_power(struct xhci_hcd *xhci, struct usb_hcd *hcd,
+void xhci_set_port_power(struct xhci_hcd *xhci, struct usb_hcd *hcd,
 				u16 index, bool on, unsigned long *flags)
 {
 	struct xhci_hub *rhub;

@@ -775,6 +775,8 @@ static void xhci_stop(struct usb_hcd *hc
 void xhci_shutdown(struct usb_hcd *hcd)
 {
 	struct xhci_hcd *xhci = hcd_to_xhci(hcd);
+	unsigned long flags;
+	int i;
 
 	if (xhci->quirks & XHCI_SPURIOUS_REBOOT)
 		usb_disable_xhci_ports(to_pci_dev(hcd->self.sysdev));

@@ -790,12 +792,21 @@ void xhci_shutdown(struct usb_hcd *hcd)
 		del_timer_sync(&xhci->shared_hcd->rh_timer);
 	}
 
-	spin_lock_irq(&xhci->lock);
+	spin_lock_irqsave(&xhci->lock, flags);
 	xhci_halt(xhci);
+
+	/* Power off USB2 ports*/
+	for (i = 0; i < xhci->usb2_rhub.num_ports; i++)
+		xhci_set_port_power(xhci, xhci->main_hcd, i, false, &flags);
+
+	/* Power off USB3 ports*/
+	for (i = 0; i < xhci->usb3_rhub.num_ports; i++)
+		xhci_set_port_power(xhci, xhci->shared_hcd, i, false, &flags);
+
 	/* Workaround for spurious wakeups at shutdown with HSW */
 	if (xhci->quirks & XHCI_SPURIOUS_WAKEUP)
 		xhci_reset(xhci, XHCI_RESET_SHORT_USEC);
-	spin_unlock_irq(&xhci->lock);
+	spin_unlock_irqrestore(&xhci->lock, flags);
 
 	xhci_cleanup_msix(xhci);
 

@@ -2155,6 +2155,8 @@ int xhci_hub_control(struct usb_hcd *hcd
 int xhci_hub_status_data(struct usb_hcd *hcd, char *buf);
 int xhci_find_raw_port_number(struct usb_hcd *hcd, int port1);
 struct xhci_hub *xhci_get_rhub(struct usb_hcd *hcd);
+void xhci_set_port_power(struct xhci_hcd *xhci, struct usb_hcd *hcd, u16 index,
+			 bool on, unsigned long *flags);
 
 void xhci_hc_died(struct xhci_hcd *xhci);
 

From: Xu Yang <[email protected]>

commit b24346a240b36cfc4df194d145463874985aa29b upstream.

The complete() function may be called even though request is not completed. In this case, it's necessary to check request status so as not to set device address wrongly.

---
 drivers/usb/chipidea/udc.c |    3 +++
 1 file changed, 3 insertions(+)

@@ -921,6 +921,9 @@ isr_setup_status_complete(struct usb_ep
 	struct ci_hdrc *ci = req->context;
 	unsigned long flags;
 
+	if (req->status < 0)
+		return;
+
 	if (ci->setaddr) {
 		hw_usb_set_address(ci, ci->address);
 		ci->setaddr = false;

From: Dmitry Rokosov <[email protected]>

commit d710359c0b445e8c03e24f19ae2fb79ce7282260 upstream.

IIO trigger interface function iio_trigger_get() should be called after iio_trigger_register() (or its devm analogue) strictly, because of iio_trigger_get() acquires module refcnt based on the trigger->owner pointer, which is initialized inside iio_trigger_register() to THIS_MODULE.
If this call order is wrong, the next iio_trigger_put() (from sysfs callback or "delete module" path) will dereference "default" module refcnt, which is incorrect behaviour.

---
 drivers/iio/chemical/ccs811.c |    4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

@@ -418,11 +418,11 @@ static int ccs811_probe(struct i2c_clien
 		data->drdy_trig->dev.parent = &client->dev;
 		data->drdy_trig->ops = &ccs811_trigger_ops;
 		iio_trigger_set_drvdata(data->drdy_trig, indio_dev);
-		indio_dev->trig = data->drdy_trig;
-		iio_trigger_get(indio_dev->trig);
 		ret = iio_trigger_register(data->drdy_trig);
 		if (ret)
 			goto err_poweroff;
+
+		indio_dev->trig = iio_trigger_get(data->drdy_trig);
 	}
 
 	ret = iio_triggered_buffer_setup(indio_dev, NULL,

From: Dmitry Rokosov <[email protected]>

commit e5f3205b04d7f95a2ef43bce4b454a7f264d6923 upstream.

IIO trigger interface function iio_trigger_get() should be called after iio_trigger_register() (or its devm analogue) strictly, because of iio_trigger_get() acquires module refcnt based on the trigger->owner pointer, which is initialized inside iio_trigger_register() to THIS_MODULE.
If this call order is wrong, the next iio_trigger_put() (from sysfs callback or "delete module" path) will dereference "default" module refcnt, which is incorrect behaviour.

---
 drivers/iio/accel/bma180.c |    3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

@@ -793,11 +793,12 @@ static int bma180_probe(struct i2c_clien
 		data->trig->dev.parent = &client->dev;
 		data->trig->ops = &bma180_trigger_ops;
 		iio_trigger_set_drvdata(data->trig, indio_dev);
-		indio_dev->trig = iio_trigger_get(data->trig);
 
 		ret = iio_trigger_register(data->trig);
 		if (ret)
 			goto err_trigger_free;
+
+		indio_dev->trig = iio_trigger_get(data->trig);
 	}
 
 	ret = iio_triggered_buffer_setup(indio_dev, NULL,

From: Dmitry Rokosov <[email protected]>

commit 9354c224c9b4f55847a0de3e968cba2ebf15af3b upstream.

IIO trigger interface function iio_trigger_get() should be called after iio_trigger_register() (or its devm analogue) strictly, because of iio_trigger_get() acquires module refcnt based on the trigger->owner pointer, which is initialized inside iio_trigger_register() to THIS_MODULE.
If this call order is wrong, the next iio_trigger_put() (from sysfs callback or "delete module" path) will dereference "default" module refcnt, which is incorrect behaviour.

---
 drivers/iio/accel/mxc4005.c |    4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

@@ -462,8 +462,6 @@ static int mxc4005_probe(struct i2c_clie
 		data->dready_trig->dev.parent = &client->dev;
 		data->dready_trig->ops = &mxc4005_trigger_ops;
 		iio_trigger_set_drvdata(data->dready_trig, indio_dev);
-		indio_dev->trig = data->dready_trig;
-		iio_trigger_get(indio_dev->trig);
 		ret = devm_iio_trigger_register(&client->dev,
 						data->dready_trig);
 		if (ret) {

@@ -471,6 +469,8 @@ static int mxc4005_probe(struct i2c_clie
 				"failed to register trigger\n");
 			return ret;
 		}
+
+		indio_dev->trig = iio_trigger_get(data->dready_trig);
 	}
 
 	return devm_iio_device_register(&client->dev, indio_dev);

From: Haibo Chen <[email protected]>

commit bf745142cc0a3e1723f9207fb0c073c88464b7b4 upstream.

On fxls8471, after set the reset bit, the device will reset immediately, will not give ACK. So ignore the return value of this reset operation, let the following code logic to check whether the reset operation works.

---
 drivers/iio/accel/mma8452.c |   10 +++++++---
 1 file changed, 7 insertions(+), 3 deletions(-)

@@ -1489,10 +1489,14 @@ static int mma8452_reset(struct i2c_clie
 	int i;
 	int ret;
 
-	ret = i2c_smbus_write_byte_data(client,	MMA8452_CTRL_REG2,
+	/*
+	 * Find on fxls8471, after config reset bit, it reset immediately,
+	 * and will not give ACK, so here do not check the return value.
+	 * The following code will read the reset register, and check whether
+	 * this reset works.
+	 */
+	i2c_smbus_write_byte_data(client, MMA8452_CTRL_REG2,
 					MMA8452_CTRL_REG2_RST);
-	if (ret < 0)
-		return ret;
 
 	for (i = 0; i < 10; i++) {
 		usleep_range(100, 200);

From: Zheyu Ma <[email protected]>

commit b2f5ad97645e1deb5ca9bcb7090084b92cae35d2 upstream.

The driver should disable regulators when fails at regmap_update_bits().

---
 drivers/iio/gyro/mpu3050-core.c |    1 +
 1 file changed, 1 insertion(+)

@@ -874,6 +874,7 @@ static int mpu3050_power_up(struct mpu30
 	ret = regmap_update_bits(mpu3050->map, MPU3050_PWR_MGM,
 				 MPU3050_PWR_MGM_SLEEP, 0);
 	if (ret) {
+		regulator_bulk_disable(ARRAY_SIZE(mpu3050->regs), mpu3050->regs);
 		dev_err(mpu3050->dev, "error setting power mode\n");
 		return ret;
 	}

From: Vincent Whitchurch <[email protected]>

commit 78601726d4a59a291acc5a52da1d3a0a6831e4e8 upstream.

Ensure that the irq_work has completed before the trigger is freed.

==================================================================

 BUG: KASAN: use-after-free in irq_work_run_list
 Read of size 8 at addr 0000000064702248 by task python3/25

 Call Trace:
  irq_work_run_list
  irq_work_tick
  update_process_times
  tick_sched_handle
  tick_sched_timer
  __hrtimer_run_queues
  hrtimer_interrupt

 Allocated by task 25:
  kmem_cache_alloc_trace
  iio_sysfs_trig_add
  dev_attr_store
  sysfs_kf_write
  kernfs_fop_write_iter
  new_sync_write
  vfs_write
  ksys_write
  sys_write

 Freed by task 25:
  kfree
  iio_sysfs_trig_remove
  dev_attr_store
  sysfs_kf_write
  kernfs_fop_write_iter
  new_sync_write
  vfs_write
  ksys_write
  sys_write

==================================================================

---
 drivers/iio/trigger/iio-trig-sysfs.c |    1 +
 1 file changed, 1 insertion(+)

@@ -196,6 +196,7 @@ static int iio_sysfs_trigger_remove(int
 	}
 
 	iio_trigger_unregister(t->trig);
+	irq_work_sync(&t->work);
 	iio_trigger_free(t->trig);
 
 	list_del(&t->l);

From: Olivier Moysan <[email protected]>

commit 990539486e7e311fb5dab1bf4d85d1a8973ae644 upstream.

Change maximum STM32 ADC input clock rate to 36MHz, as specified in STM32MP15x datasheets.

---
 drivers/iio/adc/stm32-adc-core.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

@@ -815,7 +815,7 @@ static const struct stm32_adc_priv_cfg s
 static const struct stm32_adc_priv_cfg stm32mp1_adc_priv_cfg = {
 	.regs = &stm32h7_adc_common_regs,
 	.clk_sel = stm32h7_adc_clk_sel,
-	.max_clk_rate_hz = 40000000,
+	.max_clk_rate_hz = 36000000,
 	.has_syscfg = HAS_VBOOSTER | HAS_ANASWVDD,
 	.num_irqs = 2,
 };

From: Hans de Goede <[email protected]>

commit 048058399f19d43cf21de9f5d36cd8144337d004 upstream.

Since commit 9bcf15f75cac ("iio: adc: axp288: Fix TS-pin handling") we preserve the bias current set by the firmware at boot. This fixes issues we were seeing on various models.

Some models like the Nuvision Solo 10 Draw tablet actually need the old hardcoded 80ųA bias current for battery temperature monitoring to work properly.

Add a quirk entry for the Nuvision Solo 10 Draw to the DMI quirk table to restore setting the bias current to 80ųA on this model.

---
 drivers/iio/adc/axp288_adc.c |    8 ++++++++
 1 file changed, 8 insertions(+)

@@ -196,6 +196,14 @@ static const struct dmi_system_id axp288
 		},
 		.driver_data = (void *)(uintptr_t)AXP288_ADC_TS_BIAS_80UA,
 	},
+	{
+		/* Nuvision Solo 10 Draw */
+		.matches = {
+		  DMI_MATCH(DMI_SYS_VENDOR, "TMAX"),
+		  DMI_MATCH(DMI_PRODUCT_NAME, "TM101W610L"),
+		},
+		.driver_data = (void *)(uintptr_t)AXP288_ADC_TS_BIAS_80UA,
+	},
 	{}
 };
 

From: Liang He <[email protected]>

commit 173940b3ae40114d4179c251a98ee039dc9cd5b3 upstream.

In machine_setup(), of_find_compatible_node() will return a node pointer with refcount incremented. We should use of_node_put() when it is not used anymore.

Message-Id: <[email protected]>

---
 arch/xtensa/platforms/xtfpga/setup.c |    1 +
 1 file changed, 1 insertion(+)

@@ -148,6 +148,7 @@ static int __init machine_setup(void)
 
 	if ((eth = of_find_compatible_node(eth, NULL, "opencores,ethoc")))
 		update_local_mac(eth);
+	of_node_put(eth);
 	return 0;
 }
 arch_initcall(machine_setup);

From: Liang He <[email protected]>

commit a0117dc956429f2ede17b323046e1968d1849150 upstream.

In calibrate_ccount(), of_find_compatible_node() will return a node pointer with refcount incremented. We should use of_node_put() when it is not used anymore.

Message-Id: <[email protected]>

---
 arch/xtensa/kernel/time.c |    1 +
 1 file changed, 1 insertion(+)

@@ -160,6 +160,7 @@ static void __init calibrate_ccount(void
 	cpu = of_find_compatible_node(NULL, NULL, "cdns,xtensa-cpu");
 	if (cpu) {
 		clk = of_clk_get(cpu, 0);
+		of_node_put(cpu);
 		if (!IS_ERR(clk)) {
 			ccount_freq = clk_get_rate(clk);
 			return;

From: Helge Deller <[email protected]>

commit 0a1355db36718178becd2bfe728a023933d73123 upstream.

Fix a boot crash on a c8000 machine as reported by Dave. Basically it changes patch_map() to return an alias mapping to the to-be-patched code in order to prevent writing to write-protected memory.

---
 arch/parisc/Kconfig |    1 +
 1 file changed, 1 insertion(+)

@@ -11,6 +11,7 @@ config PARISC
 	select ARCH_WANT_FRAME_POINTERS
 	select ARCH_HAS_ELF_RANDOMIZE
 	select ARCH_HAS_STRICT_KERNEL_RWX
+	select ARCH_HAS_STRICT_MODULE_RWX
 	select ARCH_HAS_UBSAN_SANITIZE_ALL
 	select ARCH_NO_SG_CHAIN
 	select ARCH_SUPPORTS_MEMORY_FAILURE

From: Naveen N. Rao <[email protected]>

commit ec6d0dde71d760aa60316f8d1c9a1b0d99213529 upstream.

On execve[at], we are zero'ing out most of the thread register state including gpr[0], which contains the syscall number. Due to this, we fail to trigger the syscall exit tracepoint properly. Fix this by retaining gpr[0] in the thread register state.

Before this patch:

  # tail /sys/kernel/debug/tracing/trace
	       cat-123     [000] .....    61.449351: sys_execve(filename:
  7fffa6b23448, argv: 7fffa6b233e0, envp: 7fffa6b233f8)
	       cat-124     [000] .....    62.428481: sys_execve(filename:
  7fffa6b23448, argv: 7fffa6b233e0, envp: 7fffa6b233f8)
	      echo-125     [000] .....    65.813702: sys_execve(filename:
  7fffa6b23378, argv: 7fffa6b233a0, envp: 7fffa6b233b0)
	      echo-125     [000] .....    65.822214: sys_execveat(fd: 0,
  filename: 1009ac48, argv: 7ffff65d0c98, envp: 7ffff65d0ca8, flags: 0)

After this patch:

  # tail /sys/kernel/debug/tracing/trace
	       cat-127     [000] .....   100.416262: sys_execve(filename:
  7fffa41b3448, argv: 7fffa41b33e0, envp: 7fffa41b33f8)
	       cat-127     [000] .....   100.418203: sys_execve -> 0x0
	      echo-128     [000] .....   103.873968: sys_execve(filename:
  7fffa41b3378, argv: 7fffa41b33a0, envp: 7fffa41b33b0)
	      echo-128     [000] .....   103.875102: sys_execve -> 0x0
	      echo-128     [000] .....   103.882097: sys_execveat(fd: 0,
  filename: 1009ac48, argv: 7fffd10d2148, envp: 7fffd10d2158, flags: 0)
	      echo-128     [000] .....   103.883225: sys_execveat -> 0x0

---
 arch/powerpc/kernel/process.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

@@ -1719,7 +1719,7 @@ void start_thread(struct pt_regs *regs,
 		tm_reclaim_current(0);
 #endif
 
-	memset(regs->gpr, 0, sizeof(regs->gpr));
+	memset(&regs->gpr[1], 0, sizeof(regs->gpr) - sizeof(regs->gpr[0]));
 	regs->ctr = 0;
 	regs->link = 0;
 	regs->xer = 0;

From: Andrew Donnellan <[email protected]>

commit 7bc08056a6dabc3a1442216daf527edf61ac24b6 upstream.

Add a special case to block_rtas_call() to allow the ibm,platform-dump RTAS call through the RTAS filter if the buffer address is 0.

According to PAPR, ibm,platform-dump is called with a null buffer address to notify the platform firmware that processing of a particular dump is finished.

Without this, on a pseries machine with CONFIG_PPC_RTAS_FILTER enabled, an application such as rtas_errd that is attempting to retrieve a dump will encounter an error at the end of the retrieval process.

---
 arch/powerpc/kernel/rtas.c |   11 ++++++++++-
 1 file changed, 10 insertions(+), 1 deletion(-)

@@ -988,7 +988,7 @@ static struct rtas_filter rtas_filters[]
 	{ "get-time-of-day", -1, -1, -1, -1, -1 },
 	{ "ibm,get-vpd", -1, 0, -1, 1, 2 },
 	{ "ibm,lpar-perftools", -1, 2, 3, -1, -1 },
-	{ "ibm,platform-dump", -1, 4, 5, -1, -1 },
+	{ "ibm,platform-dump", -1, 4, 5, -1, -1 },		/* Special cased */
 	{ "ibm,read-slot-reset-state", -1, -1, -1, -1, -1 },
 	{ "ibm,scan-log-dump", -1, 0, 1, -1, -1 },
 	{ "ibm,set-dynamic-indicator", -1, 2, -1, -1, -1 },

@@ -1035,6 +1035,15 @@ static bool block_rtas_call(int token, i
 				size = 1;
 
 			end = base + size - 1;
+
+			/*
+			 * Special case for ibm,platform-dump - NULL buffer
+			 * address is used to indicate end of dump processing
+			 */
+			if (!strcmp(f->name, "ibm,platform-dump") &&
+			    base == 0)
+				return false;
+
 			if (!in_rmo_buf(base, end))
 				goto err;
 		}

From: Jason A. Donenfeld <[email protected]>

commit f3eac426657d985b97c92fa5f7ae1d43f04721f3 upstream.

The platform's RNG must be available before random_init() in order to be useful for initial seeding, which in turn means that it needs to be called from setup_arch(), rather than from an init call.

Complicating things, however, is that POWER8 systems need some per-cpu state and kmalloc, which isn't available at this stage. So we split things up into an early phase and a later opportunistic phase. This commit also removes some noisy log messages that don't add much.

---
 arch/powerpc/platforms/powernv/powernv.h |    2 +
 arch/powerpc/platforms/powernv/rng.c     |   52 +++++++++++++++++++++----------
 arch/powerpc/platforms/powernv/setup.c   |    2 +
 3 files changed, 40 insertions(+), 16 deletions(-)

@@ -35,4 +35,6 @@ ssize_t memcons_copy(struct memcons *mc,
 u32 memcons_get_size(struct memcons *mc);
 struct memcons *memcons_init(struct device_node *node, const char *mc_prop_name);
 
+void pnv_rng_init(void);
+
 #endif /* _POWERNV_H */

@@ -168,6 +168,8 @@ static void __init pnv_setup_arch(void)
 	powersave_nap = 1;
 
 	/* XXX PMCS */
+
+	pnv_rng_init();
 }
 
 static void __init pnv_init(void)

From: Lucas Stach <[email protected]>

commit 93a8ba2a619816d631bd69e9ce2172b4d7a481b8 upstream.

Contrary to what was believed at the time, the ramp delay of 150us is not plenty for the PU LDO with the default step time of 512 pulses of the 24MHz clock. Measurements have shown that after enabling the LDO the voltage on VDDPU_CAP jumps to ~750mV in the first step and after that the regulator executes the normal ramp up as defined by the step size control.

This means it takes the regulator between 360us and 370us to ramp up to the nominal 1.15V voltage for this power domain. With the old setting of the ramp delay the power up of the PU GPC domain would happen in the middle of the regulator ramp with the voltage being at around 900mV. Apparently this was enough for most units to properly power up the peripherals in the domain and execute the reset. Some units however, fail to power up properly, especially when the chip is at a low temperature. In that case any access to the GPU registers would yield an incorrect result with no way to recover from this situation.

Change the ramp delay to 380us to cover the measured ramp up time with a bit of additional slack.

---
 arch/arm/boot/dts/imx6qdl.dtsi |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

@@ -766,7 +766,7 @@
 					regulator-name = "vddpu";
 					regulator-min-microvolt = <725000>;
 					regulator-max-microvolt = <1450000>;
-					regulator-enable-ramp-delay = <150>;
+					regulator-enable-ramp-delay = <380>;
 					anatop-reg-offset = <0x140>;
 					anatop-vol-bit-shift = <9>;
 					anatop-vol-bit-width = <5>;

From: Miaoqian Lin <[email protected]>

commit c4c79525042a4a7df96b73477feaf232fe44ae81 upstream.

of_find_matching_node() returns a node pointer with refcount incremented, we should use of_node_put() on it when not need anymore. Add missing of_node_put() to avoid refcount leak. of_node_put() checks null pointer.

---
 arch/arm/mach-exynos/exynos.c |    1 +
 1 file changed, 1 insertion(+)

@@ -136,6 +136,7 @@ static void exynos_map_pmu(void)
 	np = of_find_matching_node(NULL, exynos_dt_pmu_match);
 	if (np)
 		pmu_base_addr = of_iomap(np, 0);
+	of_node_put(np);
 }
 
 static void __init exynos_init_irq(void)

From: Miaoqian Lin <[email protected]>

commit 37d838de369b07b596c19ff3662bf0293fdb09ee upstream.

of_find_matching_node() returns a node pointer with refcount incremented, we should use of_node_put() on it when not need anymore. Add missing of_node_put() to avoid refcount leak.

In brcmstb_init_sram, it pass dn to of_address_to_resource(), of_address_to_resource() will call of_find_device_by_node() to take reference, so we should release the reference returned by of_find_matching_node().

---
 drivers/soc/bcm/brcmstb/pm/pm-arm.c |    1 +
 1 file changed, 1 insertion(+)

@@ -780,6 +780,7 @@ static int brcmstb_pm_probe(struct platf
 	}
 
 	ret = brcmstb_init_sram(dn);
+	of_node_put(dn);
 	if (ret) {
 		pr_err("error setting up SRAM for PM\n");
 		return ret;

From: Miaoqian Lin <[email protected]>

commit 7c7ff68daa93d8c4cdea482da4f2429c0398fcde upstream.

of_find_compatible_node() returns a node pointer with refcount incremented, we should use of_node_put() on it when done. Add missing of_node_put() to avoid refcount leak.

---
 arch/arm/mach-axxia/platsmp.c |    1 +
 1 file changed, 1 insertion(+)

@@ -39,6 +39,7 @@ static int axxia_boot_secondary(unsigned
 		return -ENOENT;
 
 	syscon = of_iomap(syscon_np, 0);
+	of_node_put(syscon_np);
 	if (!syscon)
 		return -ENOMEM;
 

From: Miaoqian Lin <[email protected]>

commit 1ba904b6b16e08de5aed7c1349838d9cd0d178c5 upstream.

of_find_compatible_node() returns a node pointer with refcount incremented, we should use of_node_put() on it when done. Add missing of_node_put() to avoid refcount leak.

---
 arch/arm/mach-cns3xxx/core.c |    2 ++
 1 file changed, 2 insertions(+)

@@ -376,6 +376,7 @@ static void __init cns3xxx_init(void)
 		/* De-Asscer SATA Reset */
 		cns3xxx_pwr_soft_rst(CNS3XXX_PWR_SOFTWARE_RST(SATA));
 	}
+	of_node_put(dn);
 
 	dn = of_find_compatible_node(NULL, NULL, "cavium,cns3420-sdhci");
 	if (of_device_is_available(dn)) {

@@ -389,6 +390,7 @@ static void __init cns3xxx_init(void)
 		cns3xxx_pwr_clk_en(CNS3XXX_PWR_CLK_EN(SDIO));
 		cns3xxx_pwr_soft_rst(CNS3XXX_PWR_SOFTWARE_RST(SDIO));
 	}
+	of_node_put(dn);
 
 	pm_power_off = cns3xxx_power_off;
 

From: Masahiro Yamada <[email protected]>

commit 28438794aba47a27e922857d27b31b74e8559143 upstream.

Since commit f02e8a6596b7 ("module: Sort exported symbols"), EXPORT_SYMBOL* is placed in the individual section ___ksymtab(_gpl)+<sym> (3 leading underscores instead of 2).

Since then, modpost cannot detect the bad combination of EXPORT_SYMBOL and __init/__exit.

Fix the .fromsec field.

---
 scripts/mod/modpost.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

@@ -1131,7 +1131,7 @@ static const struct sectioncheck section
 },
 /* Do not export init/exit functions or data */
 {
-	.fromsec = { "__ksymtab*", NULL },
+	.fromsec = { "___ksymtab*", NULL },
 	.bad_tosec = { INIT_SECTIONS, EXIT_SECTIONS, NULL },
 	.mismatch = EXPORT_TO_INIT_EXIT,
 	.symbol_white_list = { DEFAULT_SYMBOL_WHITE_LIST, NULL },

This commit causes the following warning to show up on my kernel builds used for testing 5.4 stable candidates:

WARNING: vmlinux.o(___ksymtab+drm_fb_helper_modinit+0x0): Section mismatch in reference from the variable __ksymtab_drm_fb_helper_modinit to the function .init.text:drm_fb_helper_modinit() The symbol drm_fb_helper_modinit is exported and annotated __init
Fix this by removing the __init annotation of drm_fb_helper_modinit or drop the export.

The kernel configuration to reproduce this is located here (this is 5.10 but works in 5.4 as well):

https://gist.github.com/2c3e8edd5ceb089c8040db724073d941

Same applies to the 5.10, 5.15 and 5.18 stable queues FWIW.

Florian

Thanks for the report. Looks like the patch is "working as intended."

It looks like drm_fb_helper_modinit was deleted outright in commit bf22c9ec39da ("drm: remove drm_fb_helper_modinit") in v5.12-rc1.

Florian, can you test if that cherry-picks cleanly and resolves the issue for you?

Maybe let's check with Christoph if it's ok to backport bf22c9ec39da to stable 5.10 and 5.4?

Thanks,
~Nick Desaulniers

It does and it does, thanks!

Florian

I'd be fine with that, but in the end it is something for the relevant maintainers to decide.

$ ./scripts/get_maintainer.pl -f drivers/gpu/drm/drm_crtc_helper_internal.h
Maarten Lankhorst <[email protected]> (maintainer:DRM
DRIVERS AND MISC GPU PATCHES)
Maxime Ripard <[email protected]> (maintainer:DRM DRIVERS AND MISC GPU PATCHES)
Thomas Zimmermann <[email protected]> (maintainer:DRM DRIVERS AND
MISC GPU PATCHES)
David Airlie <[email protected]> (maintainer:DRM DRIVERS)
Daniel Vetter <[email protected]> (maintainer:DRM DRIVERS)
[email protected] (open list:DRM DRIVERS)
[email protected] (open list)

Maarten, Maxime, Thomas, David, or Daniel,
Is it ok to backport
commit bf22c9ec39da ("drm: remove drm_fb_helper_modinit")
to 5.10.y and 5.4.y to fix the modpost warning reported by Florian in
https://lore.kernel.org/stable/[email protected]/ ?

Thanks,
~Nick Desaulniers

I've queued this up now, thanks.

greg k-h

From: Jason A. Donenfeld <[email protected]>

commit 63b8ea5e4f1a87dea4d3114293fc8e96a8f193d7 upstream.

This comment wasn't updated when we moved from read() to read_iter(), so this patch makes the trivial fix.

---
 drivers/char/random.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

@@ -450,7 +450,7 @@ static ssize_t get_random_bytes_user(str
 
 	/*
 	 * Immediately overwrite the ChaCha key at index 4 with random
-	 * bytes, in case userspace causes copy_to_user() below to sleep
+	 * bytes, in case userspace causes copy_to_iter() below to sleep
 	 * forever, so that we still retain forward secrecy in that case.
 	 */
 	crng_make_state(chacha_state, (u8 *)&chacha_state[4], CHACHA_KEY_SIZE);

From: Masahiro Yamada <[email protected]>

commit 53632ba87d9f302a8d97a11ec2f4f4eec7bb75ea upstream.

If CONFIG_TRIM_UNUSED_KSYMS is enabled and the kernel is built from a pristine state, the vmlinux is linked twice.

Commit 3fdc7d3fe4c0 ("kbuild: link vmlinux only once for CONFIG_TRIM_UNUSED_KSYMS") explains why this happens, but it did not fix the issue at all.

Now I realized I had applied a wrong patch.

In v1 patch [1], the autoksyms_recursive target correctly recurses to "$(MAKE) -f $(srctree)/Makefile autoksyms_recursive".

In v2 patch [2], I accidentally dropped the diff line, and it recurses to "$(MAKE) -f $(srctree)/Makefile vmlinux".

Restore the code I intended in v1.

[1]: https://lore.kernel.org/linux-kbuild/[email protected]/
[2]: https://lore.kernel.org/linux-kbuild/[email protected]/

---
 Makefile |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

@@ -1073,7 +1073,7 @@ PHONY += autoksyms_recursive
 ifdef CONFIG_TRIM_UNUSED_KSYMS
 autoksyms_recursive: descend modules.order
 	$(Q)$(CONFIG_SHELL) $(srctree)/scripts/adjust_autoksyms.sh \
-	  "$(MAKE) -f $(srctree)/Makefile vmlinux"
+	  "$(MAKE) -f $(srctree)/Makefile autoksyms_recursive"
 endif
 
 # For the kernel to actually contain only the needed exported symbols,

From: Jason A. Donenfeld <[email protected]>

commit e561e472a3d441753bd012333b057f48fef1045b upstream.

The platform's RNG must be available before random_init() in order to be useful for initial seeding, which in turn means that it needs to be called from setup_arch(), rather than from an init call. Fortunately, each platform already has a setup_arch function pointer, which means it's easy to wire this up. This commit also removes some noisy log messages that don't add much.

---
 arch/powerpc/platforms/pseries/pseries.h |    2 ++
 arch/powerpc/platforms/pseries/rng.c     |   11 +++--------
 arch/powerpc/platforms/pseries/setup.c   |    2 ++
 3 files changed, 7 insertions(+), 8 deletions(-)

@@ -114,4 +114,6 @@ int dlpar_workqueue_init(void);
 void pseries_setup_rfi_flush(void);
 void pseries_lpar_read_hblkrm_characteristics(void);
 
+void pseries_rng_init(void);
+
 #endif /* _PSERIES_PSERIES_H */

@@ -10,6 +10,7 @@
 #include <asm/archrandom.h>
 #include <asm/machdep.h>
 #include <asm/plpar_wrappers.h>
+#include "pseries.h"
 
 
 static int pseries_get_random_long(unsigned long *v)

@@ -24,19 +25,13 @@ static int pseries_get_random_long(unsig
 	return 0;
 }
 
-static __init int rng_init(void)
+void __init pseries_rng_init(void)
 {
 	struct device_node *dn;
 
 	dn = of_find_compatible_node(NULL, NULL, "ibm,random");
 	if (!dn)
-		return -ENODEV;
-
-	pr_info("Registering arch random hook.\n");
-
+		return;
 	ppc_md.get_random_seed = pseries_get_random_long;
-
 	of_node_put(dn);
-	return 0;
 }
-machine_subsys_initcall(pseries, rng_init);

@@ -792,6 +792,8 @@ static void __init pSeries_setup_arch(vo
 
 	if (swiotlb_force == SWIOTLB_FORCE)
 		ppc_swiotlb_enable = 1;
+
+	pseries_rng_init();
 }
 
 static void pseries_panic(char *str)

All tests passing for Tegra ...

Test results for stable-v5.4:

    10 builds:	10 pass, 0 fail
    26 boots:	26 pass, 0 fail
    59 tests:	59 pass, 0 fail

Linux version: 5.4.202-rc1-g1c351e730d68
Boards tested: tegra124-jetson-tk1, tegra186-p2771-0000,

                tegra194-p2972-0000, tegra20-ventana,
                tegra210-p2371-2180, tegra210-p3450-0000,
                tegra30-cardhu-a04

Jon

On ARCH_BRCMSTB using 32-bit and 64-bit ARM kernels:

There is however a section warning generated:

WARNING: vmlinux.o(___ksymtab+drm_fb_helper_modinit+0x0): Section mismatch in reference from the variable __ksymtab_drm_fb_helper_modinit to the function .init.text:drm_fb_helper_modinit() The symbol drm_fb_helper_modinit is exported and annotated __init
Fix this by removing the __init annotation of drm_fb_helper_modinit or drop the export.

Florian

Hello!

Results from Linaro's test farm.
The following new warnings have been found while building for all architectures with GCC:

WARNING: modpost: vmlinux.o(___ksymtab+drm_fb_helper_modinit+0x0): Section mismatch in reference from the variable __ksymtab_drm_fb_helper_modinit to the function .init.text:drm_fb_helper_modinit() The symbol drm_fb_helper_modinit is exported and annotated __init
Fix this by removing the __init annotation of drm_fb_helper_modinit or drop the export.

WARNING: modpost: drivers/gpu/drm/drm_kms_helper.o(___ksymtab+drm_fb_helper_modinit+0x0): Section mismatch in reference from the variable __ksymtab_drm_fb_helper_modinit to the function .init.text:drm_fb_helper_modinit() The symbol drm_fb_helper_modinit is exported and annotated __init
Fix this by removing the __init annotation of drm_fb_helper_modinit or drop the export.

## Build
* kernel: 5.4.202-rc1
* git: https://gitlab.com/Linaro/lkft/mirrors/stable/linux-stable-rc
* git branch: linux-5.4.y
* git commit: 1c351e730d68becde35c20fa77ae48dccd9b9fc2
* git describe: v5.4.201-61-g1c351e730d68
* test details: https://qa-reports.linaro.org/lkft/linux-stable-rc-linux-5.4.y/build/v5.4.201-61-g1c351e730d68

## No test regressions (compared to v5.4.201)

## Metric regressions (compared to v5.4.201)
* arm, build
- gcc-8-at91_dt_defconfig-warnings
- gcc-8-bcm2835_defconfig-warnings
- gcc-8-davinci_all_defconfig-warnings
- gcc-8-defconfig-warnings
- gcc-8-exynos_defconfig-warnings
- gcc-8-imx_v6_v7_defconfig-warnings
- gcc-8-integrator_defconfig-warnings
- gcc-8-ixp4xx_defconfig-warnings
- gcc-8-lpc32xx_defconfig-warnings
- gcc-8-multi_v5_defconfig-45747f0c-warnings
- gcc-8-multi_v5_defconfig-warnings
- gcc-8-mxs_defconfig-warnings
- gcc-8-nhk8815_defconfig-warnings
- gcc-8-omap2plus_defconfig-warnings
- gcc-8-s3c6400_defconfig-warnings
- gcc-8-s5pv210_defconfig-warnings
- gcc-8-sama5_defconfig-warnings
- gcc-8-u8500_defconfig-warnings
- gcc-8-vexpress_defconfig-warnings
- gcc-9-at91_dt_defconfig-warnings
- gcc-9-bcm2835_defconfig-warnings
- gcc-9-davinci_all_defconfig-warnings
- gcc-9-defconfig-warnings
- gcc-9-exynos_defconfig-warnings
- gcc-9-imx_v6_v7_defconfig-warnings
- gcc-9-integrator_defconfig-warnings
- gcc-9-ixp4xx_defconfig-warnings
- gcc-9-lpc32xx_defconfig-warnings
- gcc-9-multi_v5_defconfig-45747f0c-warnings
- gcc-9-multi_v5_defconfig-warnings
- gcc-9-mxs_defconfig-warnings
- gcc-9-nhk8815_defconfig-warnings
- gcc-9-omap2plus_defconfig-warnings
- gcc-9-s3c6400_defconfig-warnings
- gcc-9-s5pv210_defconfig-warnings
- gcc-9-sama5_defconfig-warnings
- gcc-9-u8500_defconfig-warnings
- gcc-9-vexpress_defconfig-warnings
- gcc-10-at91_dt_defconfig-warnings
- gcc-10-bcm2835_defconfig-warnings
- gcc-10-davinci_all_defconfig-warnings
- gcc-10-defconfig-warnings
- gcc-10-exynos_defconfig-warnings
- gcc-10-imx_v6_v7_defconfig-warnings
- gcc-10-integrator_defconfig-warnings
- gcc-10-ixp4xx_defconfig-warnings
- gcc-10-lkftconfig-debug-kmemleak-warnings
- gcc-10-lkftconfig-debug-warnings
- gcc-10-lkftconfig-kasan-warnings
- gcc-10-lkftconfig-kselftest-kernel-warnings
- gcc-10-lkftconfig-kselftest-warnings
- gcc-10-lkftconfig-kunit-warnings
- gcc-10-lkftconfig-libgpiod-warnings
- gcc-10-lkftconfig-perf-warnings
- gcc-10-lkftconfig-rcutorture-warnings
- gcc-10-lkftconfig-warnings
- gcc-10-lpc32xx_defconfig-warnings
- gcc-10-multi_v5_defconfig-45747f0c-warnings
- gcc-10-multi_v5_defconfig-warnings
- gcc-10-mxs_defconfig-warnings
- gcc-10-nhk8815_defconfig-warnings
- gcc-10-omap2plus_defconfig-warnings
- gcc-10-s3c6400_defconfig-warnings
- gcc-10-s5pv210_defconfig-warnings
- gcc-10-sama5_defconfig-warnings
- gcc-10-u8500_defconfig-warnings
- gcc-10-vexpress_defconfig-warnings
- gcc-11-at91_dt_defconfig-warnings
- gcc-11-bcm2835_defconfig-warnings
- gcc-11-davinci_all_defconfig-warnings
- gcc-11-defconfig-warnings
- gcc-11-exynos_defconfig-warnings
- gcc-11-imx_v6_v7_defconfig-warnings
- gcc-11-integrator_defconfig-warnings
- gcc-11-ixp4xx_defconfig-warnings
- gcc-11-lpc32xx_defconfig-warnings
- gcc-11-multi_v5_defconfig-45747f0c-warnings
- gcc-11-multi_v5_defconfig-warnings
- gcc-11-mxs_defconfig-warnings
- gcc-11-nhk8815_defconfig-warnings
- gcc-11-omap2plus_defconfig-warnings
- gcc-11-s3c6400_defconfig-warnings
- gcc-11-s5pv210_defconfig-warnings
- gcc-11-sama5_defconfig-warnings
- gcc-11-u8500_defconfig-warnings
- gcc-11-vexpress_defconfig-warnings

* arm64, build
- gcc-11-lkftconfig-64k_page_size-warnings
- gcc-11-lkftconfig-armv8_features-warnings
- gcc-11-lkftconfig-debug-kmemleak-warnings
- gcc-11-lkftconfig-debug-warnings
- gcc-11-lkftconfig-devicetree-warnings
- gcc-11-lkftconfig-kasan-warnings
- gcc-11-lkftconfig-kselftest-kernel-warnings
- gcc-11-lkftconfig-kselftest-warnings
- gcc-11-lkftconfig-kunit-warnings
- gcc-11-lkftconfig-libgpiod-warnings
- gcc-11-lkftconfig-perf-warnings
- gcc-11-lkftconfig-rcutorture-warnings
- gcc-11-lkftconfig-warnings

* i386, build
- gcc-8-i386_defconfig-warnings
- gcc-9-i386_defconfig-warnings
- gcc-10-defconfig-warnings
- gcc-11-defconfig-warnings
- gcc-11-lkftconfig-debug-kmemleak-warnings
- gcc-11-lkftconfig-debug-warnings
- gcc-11-lkftconfig-kselftest-kernel-warnings
- gcc-11-lkftconfig-kselftest-warnings
- gcc-11-lkftconfig-kunit-warnings
- gcc-11-lkftconfig-libgpiod-warnings
- gcc-11-lkftconfig-perf-warnings
- gcc-11-lkftconfig-rcutorture-warnings
- gcc-11-lkftconfig-warnings

* powerpc, build
- gcc-8-ppc6xx_defconfig-warnings
- gcc-9-ppc6xx_defconfig-warnings
- gcc-10-ppc6xx_defconfig-warnings
- gcc-11-ppc6xx_defconfig-warnings

* riscv, build
- gcc-8-defconfig-warnings
- gcc-9-defconfig-warnings
- gcc-10-defconfig-warnings
- gcc-11-defconfig-warnings

* x86_64, build
- gcc-8-x86_64_defconfig-warnings
- gcc-9-x86_64_defconfig-warnings
- gcc-10-defconfig-warnings
- gcc-11-defconfig-warnings
- gcc-11-lkftconfig-debug-kmemleak-warnings
- gcc-11-lkftconfig-debug-warnings
- gcc-11-lkftconfig-kasan-warnings
- gcc-11-lkftconfig-kselftest-kernel-warnings
- gcc-11-lkftconfig-kselftest-warnings
- gcc-11-lkftconfig-kunit-warnings
- gcc-11-lkftconfig-libgpiod-warnings
- gcc-11-lkftconfig-perf-warnings
- gcc-11-lkftconfig-rcutorture-warnings
- gcc-11-lkftconfig-warnings

## No test fixes (compared to v5.4.201)

## No metric fixes (compared to v5.4.201)

## Test result summary
total: 106600, pass: 95406, fail: 218, skip: 10208, xfail: 768

## Build Summary
* arc: 10 total, 10 passed, 0 failed
* arm: 313 total, 313 passed, 0 failed
* arm64: 57 total, 53 passed, 4 failed
* i386: 28 total, 25 passed, 3 failed
* mips: 37 total, 37 passed, 0 failed
* parisc: 12 total, 12 passed, 0 failed
* powerpc: 54 total, 54 passed, 0 failed
* riscv: 27 total, 27 passed, 0 failed
* s390: 12 total, 12 passed, 0 failed
* sh: 24 total, 24 passed, 0 failed
* sparc: 12 total, 12 passed, 0 failed
* x86_64: 55 total, 54 passed, 1 failed

## Test suites summary
* fwts
* igt-gpu-tools
* kunit
* kvm-unit-tests
* libgpiod
* libhugetlbfs
* log-parser-boot
* log-parser-test
* ltp-cap_bounds
* ltp-commands
* ltp-containers
* ltp-controllers
* ltp-cpuhotplug
* ltp-crypto
* ltp-cve
* ltp-dio
* ltp-fcntl-locktests
* ltp-filecaps
* ltp-fs
* ltp-fs_bind
* ltp-fs_perms_simple
* ltp-fsx
* ltp-hugetlb
* ltp-io
* ltp-ipc
* ltp-math
* ltp-mm
* ltp-nptl
* ltp-open-posix-tests
* ltp-pty
* ltp-sched
* ltp-securebits
* ltp-smoke
* ltp-syscalls
* ltp-tracing
* network-basic-tests
* packetdrill
* perf
* rcutorture
* ssuite
* v4l2-compliance
* vdso

Greetings!

Daniel Díaz
[email protected]

Linaro LKFT
https://lkft.linaro.org

Compiled and booted on my test system. No dmesg regressions.

thanks,
-- Shuah

Build results:

	total: 161 pass: 161 fail: 0
Qemu test results:
	total: 449 pass: 449 fail: 0

Guenter

Hi Greg,

Build test (gcc version 11.3.1 20220627):
mips: 65 configs -> no failure
arm: 106 configs -> no failure
arm64: 2 configs -> no failure
x86_64: 4 configs -> no failure
alpha allmodconfig -> no failure
powerpc allmodconfig -> no failure
riscv allmodconfig -> no failure
s390 allmodconfig -> no failure
xtensa allmodconfig -> no failure

Boot test:
x86_64: Booted on my test laptop. No regression.
x86_64: Booted on qemu. No regression. [1]

[1]. https://openqa.qa.codethink.co.uk/tests/1401

--
Regards
Sudip

Tested on arm64 and x86 for 5.4.202-rc1,

Kernel repo:
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git
Branch: linux-5.4.y
Version: 5.4.202-rc1
Commit: 1c351e730d68becde35c20fa77ae48dccd9b9fc2
Compiler: gcc version 7.3.0 (GCC)

arm64:
--------------------------------------------------------------------
Testcase Result Summary:
total: 9086
passed: 9086
failed: 0
timeout: 0
--------------------------------------------------------------------

x86:
--------------------------------------------------------------------
Testcase Result Summary:
total: 9086
passed: 9086
failed: 0
timeout: 0
--------------------------------------------------------------------