Skip to contentSkip to conversation

Miscellaneous fixes for Azoteq IQS7222A/B/C

PATCH In review Jeff LaBundy 2 participants 11 messages Jun 26, 2022 – Jun 27, 2022

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

v2 cover Miscellaneous fixes for Azoteq IQS7222A/B/C

This series comprises a handful of minor fixes that result from continued testing and updated guidance from the vendor.

Jeff LaBundy (9):
Input: iqs7222 - correct slider event disable logic
Input: iqs7222 - fortify slider event reporting
Input: iqs7222 - protect volatile registers
Input: iqs7222 - acknowledge reset before writing registers
Input: iqs7222 - handle reset during ATI
Input: iqs7222 - remove support for RF filter
dt-bindings: input: iqs7222: Remove support for RF filter
dt-bindings: input: iqs7222: Correct bottom speed step size
dt-bindings: input: iqs7222: Extend slider-mapped GPIO to IQS7222C

 .../bindings/input/azoteq,iqs7222.yaml        |  28 +--
 drivers/input/misc/iqs7222.c                  | 178 ++++++++++++------
 2 files changed, 130 insertions(+), 76 deletions(-)
Signature · 1 line
2.25.1
#1 lore raw

PATCH v2 1/9 Input: iqs7222 - correct slider event disable logic

If a positive swipe/flick gesture is defined but the corresponding negative gesture is not, the former is inadvertently disabled. Fix this by gently refactoring the logic responsible for disabling all gestures by default.

As part of this change, make the code a bit simpler by eliminating a superfluous conditional check. If a slider event does not define an enable control, the second term of the bitwise AND operation is simply 0xFFFF.

Fixes e505edaedcb9 ("Input: add support for Azoteq IQS7222A/B/C")

---
Changes in v2:
- Added to series

 drivers/input/misc/iqs7222.c | 16 +++++++++-------
 1 file changed, 9 insertions(+), 7 deletions(-)
drivers/input/misc/iqs7222.c +9 -7
index 6b4138771a3f..53df74f3a982 100644
@@ -2081,17 +2081,19 @@ static int iqs7222_parse_sldr(struct iqs7222_private *iqs7222, int sldr_index)
 			sldr_setup[0] |= dev_desc->wheel_enable;
 	}
 
+	/*
+	 * The absence of a register offset makes it safe to assume the device
+	 * supports gestures, each of which is first disabled until explicitly
+	 * enabled.
+	 */
+	if (!reg_offset)
+		for (i = 0; i < ARRAY_SIZE(iqs7222_sl_events); i++)
+			sldr_setup[9] &= ~iqs7222_sl_events[i].enable;
+
 	for (i = 0; i < ARRAY_SIZE(iqs7222_sl_events); i++) {
 		const char *event_name = iqs7222_sl_events[i].name;
 		struct fwnode_handle *event_node;
 
-		/*
-		 * The absence of a register offset means the remaining fields
-		 * in the group represent gesture settings.
-		 */
-		if (iqs7222_sl_events[i].enable && !reg_offset)
-			sldr_setup[9] &= ~iqs7222_sl_events[i].enable;
-
 		event_node = fwnode_get_named_child_node(sldr_node, event_name);
 		if (!event_node)
 			continue;
Signature · 1 line
2.25.1
#2 lore raw

PATCH v2 2/9 Input: iqs7222 - fortify slider event reporting

In reply to Jeff LaBundy

The release cycle of any key mapped to a slider gesture relies upon trailing interrupts generated by other unmasked sources, the timing and presence of which are inconsistent.

To solve this problem, explicitly report a release cycle to emulate a full keystroke. Also, unmask touch interrupts if the slider press event is defined; this ensures the device reports a final interrupt with coordinate = 0xFFFF once the finger is lifted.

As a result of how the logic has been refactored, the press/release event can now be mapped to a GPIO. This is more convenient than the previous solution, which required each channel within the slider to specify the same GPIO.

As part of this change, use the device's resolution rather than its number of interrupt status registers to more safely determine if it is capable of reporting gestures.

Last but not least, make the code a bit simpler by eliminating some unnecessarily complex conditional statements and a macro that could be derived using information that is already available.

Fixes e505edaedcb9 ("Input: add support for Azoteq IQS7222A/B/C")

---
Changes in v2:
- Minor refactoring to include GPIO-mapped press/release event
- Added support for proximity-mapped press/release event

 drivers/input/misc/iqs7222.c | 96 ++++++++++++++++++++++--------------
 1 file changed, 58 insertions(+), 38 deletions(-)
drivers/input/misc/iqs7222.c +58 -38
index 53df74f3a982..57616a7ebeae 100644
@@ -40,7 +40,6 @@
 #define IQS7222_SLDR_SETUP_2_RES_MASK		GENMASK(15, 8)
 #define IQS7222_SLDR_SETUP_2_RES_SHIFT		8
 #define IQS7222_SLDR_SETUP_2_TOP_SPEED_MASK	GENMASK(7, 0)
-#define IQS7222_SLDR_SETUP_3_CHAN_SEL_MASK	GENMASK(9, 0)
 
 #define IQS7222_GPIO_SETUP_0_GPIO_EN		BIT(0)
 
@@ -54,6 +53,9 @@
 #define IQS7222_SYS_SETUP_ACK_RESET		BIT(0)
 
 #define IQS7222_EVENT_MASK_ATI			BIT(12)
+#define IQS7222_EVENT_MASK_SLDR			BIT(10)
+#define IQS7222_EVENT_MASK_TOUCH		BIT(1)
+#define IQS7222_EVENT_MASK_PROX			BIT(0)
 
 #define IQS7222_COMMS_HOLD			BIT(0)
 #define IQS7222_COMMS_ERROR			0xEEEE
@@ -135,12 +137,12 @@ struct iqs7222_event_desc {
 static const struct iqs7222_event_desc iqs7222_kp_events[] = {
 	{
 		.name = "event-prox",
-		.enable = BIT(0),
+		.enable = IQS7222_EVENT_MASK_PROX,
 		.reg_key = IQS7222_REG_KEY_PROX,
 	},
 	{
 		.name = "event-touch",
-		.enable = BIT(1),
+		.enable = IQS7222_EVENT_MASK_TOUCH,
 		.reg_key = IQS7222_REG_KEY_TOUCH,
 	},
 };
@@ -1957,8 +1959,8 @@ static int iqs7222_parse_sldr(struct iqs7222_private *iqs7222, int sldr_index)
 	int num_chan = dev_desc->reg_grps[IQS7222_REG_GRP_CHAN].num_row;
 	int ext_chan = rounddown(num_chan, 10);
 	int count, error, reg_offset, i;
+	u16 *event_mask = &iqs7222->sys_setup[dev_desc->event_offset];
 	u16 *sldr_setup = iqs7222->sldr_setup[sldr_index];
-	u16 *sys_setup = iqs7222->sys_setup;
 	unsigned int chan_sel[4], val;
 
 	error = iqs7222_parse_props(iqs7222, &sldr_node, sldr_index,
@@ -2003,7 +2005,7 @@ static int iqs7222_parse_sldr(struct iqs7222_private *iqs7222, int sldr_index)
 	reg_offset = dev_desc->sldr_res < U16_MAX ? 0 : 1;
 
 	sldr_setup[0] |= count;
-	sldr_setup[3 + reg_offset] &= ~IQS7222_SLDR_SETUP_3_CHAN_SEL_MASK;
+	sldr_setup[3 + reg_offset] &= ~GENMASK(ext_chan - 1, 0);
 
 	for (i = 0; i < ARRAY_SIZE(chan_sel); i++) {
 		sldr_setup[5 + reg_offset + i] = 0;
@@ -2106,6 +2108,22 @@ static int iqs7222_parse_sldr(struct iqs7222_private *iqs7222, int sldr_index)
 		if (error)
 			return error;
 
+		/*
+		 * The press/release event does not expose a direct GPIO link,
+		 * but one can be emulated by tying each of the participating
+		 * channels to the same GPIO.
+		 */
+		error = iqs7222_gpio_select(iqs7222, event_node,
+					    i ? iqs7222_sl_events[i].enable
+					      : sldr_setup[3 + reg_offset],
+					    i ? 1568 + sldr_index * 30
+					      : sldr_setup[4 + reg_offset]);
+		if (error)
+			return error;
+
+		if (!reg_offset)
+			sldr_setup[9] |= iqs7222_sl_events[i].enable;
+
 		error = fwnode_property_read_u32(event_node, "linux,code",
 						 &val);
 		if (error) {
@@ -2117,26 +2135,20 @@ static int iqs7222_parse_sldr(struct iqs7222_private *iqs7222, int sldr_index)
 		iqs7222->sl_code[sldr_index][i] = val;
 		input_set_capability(iqs7222->keypad, EV_KEY, val);
 
-		/*
-		 * The press/release event is determined based on whether the
-		 * coordinate field reports 0xFFFF and has no explicit enable
-		 * control.
-		 */
-		if (!iqs7222_sl_events[i].enable || reg_offset)
-			continue;
-
-		sldr_setup[9] |= iqs7222_sl_events[i].enable;
-
-		error = iqs7222_gpio_select(iqs7222, event_node,
-					    iqs7222_sl_events[i].enable,
-					    1568 + sldr_index * 30);
-		if (error)
-			return error;
-
 		if (!dev_desc->event_offset)
 			continue;
 
-		sys_setup[dev_desc->event_offset] |= BIT(10 + sldr_index);
+		/*
+		 * The press/release event is determined based on whether the
+		 * coordinate field reports 0xFFFF and solely relies on touch
+		 * or proximity interrupts to be unmasked.
+		 */
+		if (i && !reg_offset)
+			*event_mask |= (IQS7222_EVENT_MASK_SLDR << sldr_index);
+		else if (sldr_setup[4 + reg_offset] == dev_desc->touch_link)
+			*event_mask |= IQS7222_EVENT_MASK_TOUCH;
+		else
+			*event_mask |= IQS7222_EVENT_MASK_PROX;
 	}
 
 	/*
@@ -2301,29 +2313,37 @@ static int iqs7222_report(struct iqs7222_private *iqs7222)
 			input_report_abs(iqs7222->keypad, iqs7222->sl_axis[i],
 					 sldr_pos);
 
-		for (j = 0; j < ARRAY_SIZE(iqs7222_sl_events); j++) {
-			u16 mask = iqs7222_sl_events[j].mask;
-			u16 val = iqs7222_sl_events[j].val;
+		input_report_key(iqs7222->keypad, iqs7222->sl_code[i][0],
+				 sldr_pos < dev_desc->sldr_res);
 
-			if (!iqs7222_sl_events[j].enable) {
-				input_report_key(iqs7222->keypad,
-						 iqs7222->sl_code[i][j],
-						 sldr_pos < dev_desc->sldr_res);
-				continue;
-			}
+		/*
+		 * A maximum resolution indicates the device does not support
+		 * gestures, in which case the remaining fields are ignored.
+		 */
+		if (dev_desc->sldr_res == U16_MAX)
+			continue;
 
-			/*
-			 * The remaining offsets represent gesture state, and
-			 * are discarded in the case of IQS7222C because only
-			 * absolute position is reported.
-			 */
-			if (num_stat < IQS7222_MAX_COLS_STAT)
-				continue;
+		if (!(le16_to_cpu(status[1]) & IQS7222_EVENT_MASK_SLDR << i))
+			continue;
+
+		/*
+		 * Skip the press/release event, as it does not have separate
+		 * status fields and is handled separately.
+		 */
+		for (j = 1; j < ARRAY_SIZE(iqs7222_sl_events); j++) {
+			u16 mask = iqs7222_sl_events[j].mask;
+			u16 val = iqs7222_sl_events[j].val;
 
 			input_report_key(iqs7222->keypad,
 					 iqs7222->sl_code[i][j],
 					 (state & mask) == val);
 		}
+
+		input_sync(iqs7222->keypad);
+
+		for (j = 1; j < ARRAY_SIZE(iqs7222_sl_events); j++)
+			input_report_key(iqs7222->keypad,
+					 iqs7222->sl_code[i][j], 0);
 	}
 
 	input_sync(iqs7222->keypad);
Signature · 1 line
2.25.1
#3 lore raw

PATCH v2 3/9 Input: iqs7222 - protect volatile registers

In reply to Jeff LaBundy

Select variants of silicon silently mirror part of the event mask register to the system setup register (0xD0), and vice versa. For the following sequence:

1. Read registers 0xD0 onward and store their contents.
2. Modify the contents, including event mask fields.
3. Write registers 0xD0 onward with the modified contents.
4. Write register 0xD0 on its own again later, using the contents from step 1 to populate any reserved fields.

...the event mask register (e.g. address 0xDA) has been corrupted by writing register 0xD0 with contents that were made stale after step 3.

To solve this problem, read register 0xD0 once more between steps 3 and 4. When register 0xD0 is written during step 4, the portion which is mirrored to the event mask register already matches what was written in step 3.

Fixes e505edaedcb9 ("Input: add support for Azoteq IQS7222A/B/C")

---
Changes in v2:
- None

 drivers/input/misc/iqs7222.c | 18 ++++++++++++++----
 1 file changed, 14 insertions(+), 4 deletions(-)
drivers/input/misc/iqs7222.c +14 -4
index 57616a7ebeae..c46d3c8f0230 100644
@@ -1274,9 +1274,22 @@ static int iqs7222_ati_trigger(struct iqs7222_private *iqs7222)
 	struct i2c_client *client = iqs7222->client;
 	ktime_t ati_timeout;
 	u16 sys_status = 0;
-	u16 sys_setup = iqs7222->sys_setup[0] & ~IQS7222_SYS_SETUP_ACK_RESET;
+	u16 sys_setup;
 	int error, i;
 
+	/*
+	 * The reserved fields of the system setup register may have changed
+	 * as a result of other registers having been written. As such, read
+	 * the register's latest value to avoid unexpected behavior when the
+	 * register is written in the loop that follows.
+	 */
+	error = iqs7222_read_word(iqs7222, IQS7222_SYS_SETUP, &sys_setup);
+	if (error)
+		return error;
+
+	sys_setup &= ~IQS7222_SYS_SETUP_INTF_MODE_MASK;
+	sys_setup &= ~IQS7222_SYS_SETUP_PWR_MODE_MASK;
+
 	for (i = 0; i < IQS7222_NUM_RETRIES; i++) {
 		/*
 		 * Trigger ATI from streaming and normal-power modes so that
@@ -2241,9 +2254,6 @@ static int iqs7222_parse_all(struct iqs7222_private *iqs7222)
 			return error;
 	}
 
-	sys_setup[0] &= ~IQS7222_SYS_SETUP_INTF_MODE_MASK;
-	sys_setup[0] &= ~IQS7222_SYS_SETUP_PWR_MODE_MASK;
-
 	sys_setup[0] |= IQS7222_SYS_SETUP_ACK_RESET;
 
 	return iqs7222_parse_props(iqs7222, NULL, 0, IQS7222_REG_GRP_SYS,
Signature · 1 line
2.25.1
#4 lore raw

PATCH v2 4/9 Input: iqs7222 - acknowledge reset before writing registers

In reply to Jeff LaBundy

If the device suffers a spurious reset while reacting to a previous spurious reset, the second reset interrupt is preempted because the ACK_RESET bit is written last.

To solve this problem, write the ACK_RESET bit prior to writing any other registers. This ensures that any registers written before the second spurious reset will be rewritten.

Last but not least, the order in which the ACK_RESET bit is written relative to the second filter beta register is important for select variants of silicon. Enforce the correct order so as to not clobber the system status register.

Fixes e505edaedcb9 ("Input: add support for Azoteq IQS7222A/B/C")

---
Changes in v2:
- None

 drivers/input/misc/iqs7222.c | 32 +++++++++++++++++++++++++++++---
 1 file changed, 29 insertions(+), 3 deletions(-)
drivers/input/misc/iqs7222.c +29 -3
index c46d3c8f0230..aa46f2cd4d34 100644
@@ -94,11 +94,11 @@ enum iqs7222_reg_key_id {
 
 enum iqs7222_reg_grp_id {
 	IQS7222_REG_GRP_STAT,
+	IQS7222_REG_GRP_FILT,
 	IQS7222_REG_GRP_CYCLE,
 	IQS7222_REG_GRP_GLBL,
 	IQS7222_REG_GRP_BTN,
 	IQS7222_REG_GRP_CHAN,
-	IQS7222_REG_GRP_FILT,
 	IQS7222_REG_GRP_SLDR,
 	IQS7222_REG_GRP_GPIO,
 	IQS7222_REG_GRP_SYS,
@@ -1348,6 +1348,34 @@ static int iqs7222_dev_init(struct iqs7222_private *iqs7222, int dir)
 	int comms_offset = dev_desc->comms_offset;
 	int error, i, j, k;
 
+	/*
+	 * Acknowledge reset before writing any registers in case the device
+	 * suffers a spurious reset during initialization. Because this step
+	 * may change the reserved fields of the second filter beta register,
+	 * its cache must be updated.
+	 *
+	 * Writing the second filter beta register, in turn, may clobber the
+	 * system status register. As such, the filter beta register pair is
+	 * written first to protect against this hazard.
+	 */
+	if (dir == WRITE) {
+		u16 reg = dev_desc->reg_grps[IQS7222_REG_GRP_FILT].base + 1;
+		u16 filt_setup;
+
+		error = iqs7222_write_word(iqs7222, IQS7222_SYS_SETUP,
+					   iqs7222->sys_setup[0] |
+					   IQS7222_SYS_SETUP_ACK_RESET);
+		if (error)
+			return error;
+
+		error = iqs7222_read_word(iqs7222, reg, &filt_setup);
+		if (error)
+			return error;
+
+		iqs7222->filt_setup[1] &= GENMASK(7, 0);
+		iqs7222->filt_setup[1] |= (filt_setup & ~GENMASK(7, 0));
+	}
+
 	/*
 	 * Take advantage of the stop-bit disable function, if available, to
 	 * save the trouble of having to reopen a communication window after
@@ -2254,8 +2282,6 @@ static int iqs7222_parse_all(struct iqs7222_private *iqs7222)
 			return error;
 	}
 
-	sys_setup[0] |= IQS7222_SYS_SETUP_ACK_RESET;
-
 	return iqs7222_parse_props(iqs7222, NULL, 0, IQS7222_REG_GRP_SYS,
 				   IQS7222_REG_KEY_NONE);
 }
Signature · 1 line
2.25.1
#5 lore raw

PATCH v2 5/9 Input: iqs7222 - handle reset during ATI

In reply to Jeff LaBundy

If the device suffers a spurious reset during ATI, there is no point in enduring any further retries. Instead, simply return successfully from the polling loop.

In this case, the interrupt handler will intervene and recognize the device has been reset. It then proceeds to initialize the device and trigger ATI once more.

As part of this change, swap the order of status field evaluation to match that of the interrupt handler, and correct a nearby off-by-one error that causes an error message to suggest the final attempt will be retried.

Fixes e505edaedcb9 ("Input: add support for Azoteq IQS7222A/B/C")

---
Changes in v2:
- None

 drivers/input/misc/iqs7222.c | 9 ++++++---
 1 file changed, 6 insertions(+), 3 deletions(-)
drivers/input/misc/iqs7222.c +6 -3
index aa46f2cd4d34..e65260d290cc 100644
@@ -1314,12 +1314,15 @@ static int iqs7222_ati_trigger(struct iqs7222_private *iqs7222)
 			if (error)
 				return error;
 
-			if (sys_status & IQS7222_SYS_STATUS_ATI_ACTIVE)
-				continue;
+			if (sys_status & IQS7222_SYS_STATUS_RESET)
+				return 0;
 
 			if (sys_status & IQS7222_SYS_STATUS_ATI_ERROR)
 				break;
 
+			if (sys_status & IQS7222_SYS_STATUS_ATI_ACTIVE)
+				continue;
+
 			/*
 			 * Use stream-in-touch mode if either slider reports
 			 * absolute position.
@@ -1336,7 +1339,7 @@ static int iqs7222_ati_trigger(struct iqs7222_private *iqs7222)
 		dev_err(&client->dev,
 			"ATI attempt %d of %d failed with status 0x%02X, %s\n",
 			i + 1, IQS7222_NUM_RETRIES, (u8)sys_status,
-			i < IQS7222_NUM_RETRIES ? "retrying..." : "stopping");
+			i + 1 < IQS7222_NUM_RETRIES ? "retrying" : "stopping");
 	}
 
 	return -ETIMEDOUT;
Signature · 1 line
2.25.1
#6 lore raw

PATCH v2 6/9 Input: iqs7222 - remove support for RF filter

In reply to Jeff LaBundy

The vendor has marked the RF filter enable control as reserved in the datasheet; remove it from the driver.

Fixes e505edaedcb9 ("Input: add support for Azoteq IQS7222A/B/C")

---
Changes in v2:
- Clarified commit message

 drivers/input/misc/iqs7222.c | 7 -------
 1 file changed, 7 deletions(-)
drivers/input/misc/iqs7222.c +0 -7
index e65260d290cc..b2e8097a2e6d 100644
@@ -557,13 +557,6 @@ static const struct iqs7222_prop_desc iqs7222_props[] = {
 		.reg_width = 4,
 		.label = "current reference trim",
 	},
-	{
-		.name = "azoteq,rf-filt-enable",
-		.reg_grp = IQS7222_REG_GRP_GLBL,
-		.reg_offset = 0,
-		.reg_shift = 15,
-		.reg_width = 1,
-	},
 	{
 		.name = "azoteq,max-counts",
 		.reg_grp = IQS7222_REG_GRP_GLBL,
Signature · 1 line
2.25.1
#7 lore raw

PATCH v2 7/9 dt-bindings: input: iqs7222: Remove support for RF filter

In reply to Jeff LaBundy

The vendor has marked the RF filter enable control as reserved in the datasheet; remove it from the binding.

Fixes 44dc42d254bf ("dt-bindings: input: Add bindings for Azoteq IQS7222A/B/C")

---
Changes in v2:
- Clarified commit message

 Documentation/devicetree/bindings/input/azoteq,iqs7222.yaml | 4 ----
 1 file changed, 4 deletions(-)
Documentation/devicetree/bindings/input/azoteq,iqs7222.yaml +0 -4
index a3a1e5a65306..6180f7ee2284 100644
@@ -37,10 +37,6 @@ properties:
       device is temporarily held in hardware reset prior to initialization if
       this property is present.
 
-  azoteq,rf-filt-enable:
-    type: boolean
-    description: Enables the device's internal RF filter.
-
   azoteq,max-counts:
     $ref: /schemas/types.yaml#/definitions/uint32
     enum: [0, 1, 2, 3]
Signature · 1 line
2.25.1
#8 lore raw

PATCH v2 8/9 dt-bindings: input: iqs7222: Correct bottom speed step size

In reply to Jeff LaBundy

The bottom speed property is specified in steps of 1, not 4.

Fixes 44dc42d254bf ("dt-bindings: input: Add bindings for Azoteq IQS7222A/B/C")

---
Changes in v2:
- None

 Documentation/devicetree/bindings/input/azoteq,iqs7222.yaml | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)
Documentation/devicetree/bindings/input/azoteq,iqs7222.yaml +1 -2
index 6180f7ee2284..c9c3a1e9bcae 100644
@@ -533,9 +533,8 @@ patternProperties:
 
       azoteq,bottom-speed:
         $ref: /schemas/types.yaml#/definitions/uint32
-        multipleOf: 4
         minimum: 0
-        maximum: 1020
+        maximum: 255
         description:
           Specifies the speed of movement after which coordinate filtering is
           linearly reduced.
Signature · 1 line
2.25.1
#9 lore raw

PATCH v2 9/9 dt-bindings: input: iqs7222: Extend slider-mapped GPIO to IQS7222C

In reply to Jeff LaBundy

Although the IQS7222C does not offer slider gesture support, the press/release event can still be mapped to any of the IQS7222C's three GPIO pins. Update the binding to reflect this relationship.

Fixes 44dc42d254bf ("dt-bindings: input: Add bindings for Azoteq IQS7222A/B/C")

---
Changes in v2:
- Added to series

 .../bindings/input/azoteq,iqs7222.yaml        | 21 ++++++++++++-------
 1 file changed, 13 insertions(+), 8 deletions(-)
Documentation/devicetree/bindings/input/azoteq,iqs7222.yaml +13 -8
index c9c3a1e9bcae..32d0d5190334 100644
@@ -611,16 +611,15 @@ patternProperties:
           azoteq,gpio-select:
             $ref: /schemas/types.yaml#/definitions/uint32-array
             minItems: 1
-            maxItems: 1
+            maxItems: 3
             items:
               minimum: 0
-              maximum: 0
+              maximum: 2
             description: |
-              Specifies an individual GPIO mapped to a tap, swipe or flick
-              gesture as follows:
+              Specifies one or more GPIO mapped to the event as follows:
               0: GPIO0
-              1: GPIO3 (reserved)
-              2: GPIO4 (reserved)
+              1: GPIO3 (IQS7222C only)
+              2: GPIO4 (IQS7222C only)
 
               Note that although multiple events can be mapped to a single
               GPIO, they must all be of the same type (proximity, touch or
@@ -705,6 +704,14 @@ allOf:
               multipleOf: 4
               maximum: 1020
 
+          patternProperties:
+            "^event-(press|tap|(swipe|flick)-(pos|neg))$":
+              properties:
+                azoteq,gpio-select:
+                  maxItems: 1
+                  items:
+                    maximum: 0
+
     else:
       patternProperties:
         "^channel-([0-9]|1[0-9])$":
@@ -721,8 +728,6 @@ allOf:
 
                 azoteq,gesture-dist: false
 
-                azoteq,gpio-select: false
-
 required:
   - compatible
   - reg
Signature · 1 line
2.25.1
maintainer
#10 lore raw
In reply to Jeff LaBundy
Quoted 14 lines · Jeff LaBundy

This series comprises a handful of minor fixes that result from continued testing and updated guidance from the vendor.

Jeff LaBundy (9):
Input: iqs7222 - correct slider event disable logic
Input: iqs7222 - fortify slider event reporting
Input: iqs7222 - protect volatile registers
Input: iqs7222 - acknowledge reset before writing registers
Input: iqs7222 - handle reset during ATI
Input: iqs7222 - remove support for RF filter
dt-bindings: input: iqs7222: Remove support for RF filter
dt-bindings: input: iqs7222: Correct bottom speed step size
dt-bindings: input: iqs7222: Extend slider-mapped GPIO to IQS7222C

Quoted 3 lines
 .../bindings/input/azoteq,iqs7222.yaml        |  28 +--
 drivers/input/misc/iqs7222.c                  | 178 ++++++++++++------
 2 files changed, 130 insertions(+), 76 deletions(-)

Applied the lot, thank you.

Signature · 1 line
Dmitry