Skip to contentSkip to conversation

Fix for MediaTek reset affecting Focusrite audio interfaces

PATCH In review Geoffrey D. Bennett 7 participants 9 messages Mar 8, 2025 – Mar 13, 2025

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

cover Fix for MediaTek reset affecting Focusrite audio interfaces

This series (choose 1 of the 2 patches) addresses an issue where the MT7922 Bluetooth controller reset added in commit ccfc8948d7e4 ("Bluetooth: btusb: mediatek: reset the controller before downloading the fw") is causing Focusrite USB audio devices to fail to initialise when connected during boot on kernels 6.11 and newer.

Reported by three users here:
https://github.com/geoffreybennett/linux-fcp/issues/24

Two users confirmed they have an MT7922.

I'm providing two possible solutions as I note there was a similar change made in commit a7208610761a ("Bluetooth: btmtk: Remove resetting mt7921 before downloading the fw"), so I'm not sure if the reset should be reverted for the MT7925 as well as the MT7922.

Option 1: Revert the problematic reset behaviour entirely (MT7922 + MT7925)

Option 2: Remove the reset only for the MT7922

Geoffrey D. Bennett (2):

[PATCH 1/2] Revert "Bluetooth: btusb: mediatek: reset the controller
before downloading the fw"

[PATCH 2/2] Bluetooth: btmtk: Remove resetting mt7922 before
downloading the fw

--
2.45.0

#1 lore raw
Quoted 23 lines · Geoffrey D. Bennett

This series (choose 1 of the 2 patches) addresses an issue where the MT7922 Bluetooth controller reset added in commit ccfc8948d7e4 ("Bluetooth: btusb: mediatek: reset the controller before downloading the fw") is causing Focusrite USB audio devices to fail to initialise when connected during boot on kernels 6.11 and newer.

Reported by three users here:
https://github.com/geoffreybennett/linux-fcp/issues/24

Two users confirmed they have an MT7922.

I'm providing two possible solutions as I note there was a similar change made in commit a7208610761a ("Bluetooth: btmtk: Remove resetting mt7921 before downloading the fw"), so I'm not sure if the reset should be reverted for the MT7925 as well as the MT7922.

Option 1: Revert the problematic reset behaviour entirely (MT7922 + MT7925)

Option 2: Remove the reset only for the MT7922

Geoffrey D. Bennett (2):

Quoted 10 lines

[PATCH 1/2] Revert "Bluetooth: btusb: mediatek: reset the controller
before downloading the fw"

[PATCH 2/2] Bluetooth: btmtk: Remove resetting mt7922 before
downloading the fw

--
2.45.0

Hi Geoffrey,

I understand there's no apparent nexus of causality here.

However if three different users suddenly reported the same problem and the fix fixes it, we should take the report seriously and back down on the problematic commit until we figure for sure what the heck is going on.

My bet is this is bona fide bug in the USB subsystem, but either I'm not looking hard enough or I'm looking into the wrong places, because there's no way I can see in which way USB bluetooth driver from MediaTek could cause clock detection to fail.

No point in pressing this harder, but yeah, take the reports more than seriously, because if we don't understand in which way our own (Linux) code could be causing this, at least we should take cautionary measures.

In that sense, putting Takashi Iwai and Greg KH to Cc: in a modest but sincere belief that this issue is more than real, even though it looks like anticipated April 1st. Takashi can help with his expertise in clock detection and Greg could help pinpoint if this is indeed madness in the USB subsystem.

Hope you and them don't mind the escalation :)

Thanks,
Geraldo Nascimento

#2 lore raw

Hi Chris, Sean, Hao,

Quoted 54 lines · Geraldo Nascimento
Quoted 23 lines · Geoffrey D. Bennett

This series (choose 1 of the 2 patches) addresses an issue where the MT7922 Bluetooth controller reset added in commit ccfc8948d7e4 ("Bluetooth: btusb: mediatek: reset the controller before downloading the fw") is causing Focusrite USB audio devices to fail to initialise when connected during boot on kernels 6.11 and newer.

Reported by three users here:
https://github.com/geoffreybennett/linux-fcp/issues/24

Two users confirmed they have an MT7922.

I'm providing two possible solutions as I note there was a similar change made in commit a7208610761a ("Bluetooth: btmtk: Remove resetting mt7921 before downloading the fw"), so I'm not sure if the reset should be reverted for the MT7925 as well as the MT7922.

Option 1: Revert the problematic reset behaviour entirely (MT7922 + MT7925)

Option 2: Remove the reset only for the MT7922

Geoffrey D. Bennett (2):

Quoted 10 lines

[PATCH 1/2] Revert "Bluetooth: btusb: mediatek: reset the controller
before downloading the fw"

[PATCH 2/2] Bluetooth: btmtk: Remove resetting mt7922 before
downloading the fw

--
2.45.0

Hi Geoffrey,

I understand there's no apparent nexus of causality here.

However if three different users suddenly reported the same problem and the fix fixes it, we should take the report seriously and back down on the problematic commit until we figure for sure what the heck is going on.

My bet is this is bona fide bug in the USB subsystem, but either I'm not looking hard enough or I'm looking into the wrong places, because there's no way I can see in which way USB bluetooth driver from MediaTek could cause clock detection to fail.

No point in pressing this harder, but yeah, take the reports more than seriously, because if we don't understand in which way our own (Linux) code could be causing this, at least we should take cautionary measures.

Quoted 7 lines

In that sense, putting Takashi Iwai and Greg KH to Cc: in a modest but sincere belief that this issue is more than real, even though it looks like anticipated April 1st. Takashi can help with his expertise in clock detection and Greg could help pinpoint if this is indeed madness in the USB subsystem.

Hope you and them don't mind the escalation :)

Do you guys have any idea what could be possibly going on here? There really seems something is not right if one driver affects the other, especially if the devices are not actually related in any way.

Signature · 1 line
Luiz Augusto von Dentz
#3 lore raw
Quoted 81 lines · Luiz Augusto von Dentz

Hi Chris, Sean, Hao,

Quoted 77 lines · Geraldo Nascimento
Quoted 33 lines · Geoffrey D. Bennett

This series (choose 1 of the 2 patches) addresses an issue where the
MT7922 Bluetooth controller reset added in commit ccfc8948d7e4 ("Bluetooth: btusb: mediatek: reset the controller before downloading
the fw") is causing Focusrite USB audio devices to fail to initialise
when connected during boot on kernels 6.11 and newer.

Reported by three users here:
https://github.com/geoffreybennett/linux-fcp/issues/24

Two users confirmed they have an MT7922.

I'm providing two possible solutions as I note there was a similar
change made in commit a7208610761a ("Bluetooth: btmtk: Remove resetting mt7921 before downloading the fw"), so I'm not sure if the
reset should be reverted for the MT7925 as well as the MT7922.

Option 1: Revert the problematic reset behaviour entirely (MT7922 +
MT7925)

Option 2: Remove the reset only for the MT7922

Geoffrey D. Bennett (2):

  [PATCH 1/2] Revert "Bluetooth: btusb: mediatek: reset the controller
    before downloading the fw"

Quoted 7 lines

  [PATCH 2/2] Bluetooth: btmtk: Remove resetting mt7922 before downloading the fw

--
2.45.0

Hi Geoffrey,

I understand there's no apparent nexus of causality here.

However if three different users suddenly reported the same problem and
the fix fixes it, we should take the report seriously and back down on the problematic commit until we figure for sure what the heck is going on.

My bet is this is bona fide bug in the USB subsystem, but either I'm not
looking hard enough or I'm looking into the wrong places, because there's no way I can see in which way USB bluetooth driver from MediaTek could cause clock detection to fail.

No point in pressing this harder, but yeah, take the reports more than
seriously, because if we don't understand in which way our own (Linux)
code could be causing this, at least we should take cautionary measures.

In that sense, putting Takashi Iwai and Greg KH to Cc: in a modest but
sincere belief that this issue is more than real, even though it looks
like anticipated April 1st. Takashi can help with his expertise in clock
detection and Greg could help pinpoint if this is indeed madness in the
USB subsystem.

Quoted 7 lines
Quoted 1 line

Hope you and them don't mind the escalation :)

Do you guys have any idea what could be possibly going on here? There really seems something is not right if one driver affects the other, especially if the devices are not actually related in any way.

Hello everyone,

I did the kernel bisection on this issue and tested Geoffrey's patches since I own the affected combination of hardware and can reliably reproduce the issue.

I was now able to capture both the sound device initialization failure and the successful initialization from initramfs using the usbmon module. One difference that is immediately noticeable is the amount of URB_CONTROL data that is sent to the mediatek btusb device and a considerable slow-down of the boot process (around 16s difference).

Following is some more information about the timing and other related messages from the kernel message log. The first excerpt is from an unpatched kernel 6.14.0-rc5:

[   59.987242] lunar kernel: usb 1-2: new high-speed USB device number 2 using xhci_hcd
[   59.987975] lunar kernel: usb 1-2: New USB device found, idVendor=1235, idProduct=8212, bcdDevice= 6.45
[   59.988048] lunar kernel: usb 1-2: New USB device strings: Mfr=1, Product=3, SerialNumber=2
[   59.988121] lunar kernel: usb 1-2: Product: Scarlett 4i4 USB
[   59.988197] lunar kernel: usb 1-2: Manufacturer: Focusrite
[   60.571193] lunar kernel: mt7921e 0000:0a:00.0: enabling device (0000 -> 0002)
[   60.571314] lunar kernel: mt7921e 0000:0a:00.0: ASIC revision: 79220010
[   60.571501] lunar kernel: usbcore: registered new interface driver btusb
[   60.571513] lunar kernel: mt7921e 0000:0a:00.0: HW/SW Version: 0x8a108a10, Build Time: 20241106163228a
[   60.571627] lunar kernel: mt7921e 0000:0a:00.0: WM Firmware Version: ____000000, Build Time: 20241106163310
[   60.616673] lunar kernel: Bluetooth: hci0: HW/SW Version: 0x008a008a, Build Time: 20241106163512
[   64.549017] lunar kernel: mt7921e 0000:0a:00.0 wlp10s0: renamed from wlan0
[   70.700407] lunar kernel: usb 1-2: parse_audio_format_rates_v2v3(): unable to retrieve number of sample rates (clock 41)
[   81.264360] lunar kernel: usb 1-2: parse_audio_format_rates_v2v3(): unable to retrieve number of sample rates (clock 41)
[   81.264611] lunar kernel: usb 1-2: Focusrite Scarlett Gen 3 Mixer Driver enabled (pid=0x8212); report any issues to https://github.com/geoffreybennett/scarlett-gen2/issues
[   81.264782] lunar kernel: usb 1-2: Error initialising Scarlett Gen 3 Mixer Driver: -71
[   81.264903] lunar kernel: snd-usb-audio 1-2:1.0: probe with driver snd-usb-audio failed with error -71
[   81.265040] lunar kernel: usb 1-2: Quirk or no altset; falling back to MIDI 1.0
[   81.400030] lunar kernel: Bluetooth: hci0: Device setup in 20435397 usecs
[   81.400114] lunar kernel: Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported.
[   81.680052] lunar kernel: Bluetooth: hci0: AOSP extensions version v1.00
[   81.680170] lunar kernel: Bluetooth: hci0: AOSP quality report is supported
[   87.373353] lunar kernel: usbcore: registered new interface driver snd-usb-audio

The following second excerpt is from the same kernel version with Geoffrey's second patch applied:

[  139.603887] lunar kernel: usb 1-2: new high-speed USB device number 2 using xhci_hcd
[  139.604524] lunar kernel: usb 1-2: New USB device found, idVendor=1235, idProduct=8212, bcdDevice= 6.45
[  139.604598] lunar kernel: usb 1-2: New USB device strings: Mfr=1, Product=3, SerialNumber=2
[  139.604672] lunar kernel: usb 1-2: Product: Scarlett 4i4 USB
[  139.604744] lunar kernel: usb 1-2: Manufacturer: Focusrite
[  140.192488] lunar kernel: usbcore: registered new interface driver btusb
[  140.192501] lunar kernel: mt7921e 0000:0a:00.0: enabling device (0000 -> 0002)
[  140.192627] lunar kernel: Bluetooth: hci0: HW/SW Version: 0x008a008a, Build Time: 20241106163512
[  140.192639] lunar kernel: mt7921e 0000:0a:00.0: ASIC revision: 79220010
[  140.192753] lunar kernel: mt7921e 0000:0a:00.0: HW/SW Version: 0x8a108a10, Build Time: 20241106163228a
[  140.192866] lunar kernel: mt7921e 0000:0a:00.0: WM Firmware Version: ____000000, Build Time: 20241106163310
[  140.240011] lunar kernel: Bluetooth: hci0: Device setup in 188119 usecs
[  140.240048] lunar kernel: Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported.
[  140.513341] lunar kernel: Bluetooth: hci0: AOSP extensions version v1.00
[  140.513379] lunar kernel: Bluetooth: hci0: AOSP quality report is supported
[  144.115475] lunar kernel: mt7921e 0000:0a:00.0 wlp10s0: renamed from wlan0
[  144.115747] lunar kernel: usb 1-2: Focusrite Scarlett Gen 3 Mixer Driver enabled (pid=0x8212); report any issues to https://github.com/geoffreybennett/scarlett-gen2/issues
[  144.115857] lunar kernel: usb 1-2: Firmware version 1605
[  144.115954] lunar kernel: usb 1-2: Quirk or no altset; falling back to MIDI 1.0
[  147.843340] lunar kernel: usbcore: registered new interface driver snd-usb-audio

Comparing the USB captures from the hub, filtered to just the first few messages of the audio device yield the following exchanges. Again, first the broken case:

No.     Time           Source                Destination           Protocol Length Info
      7 0.011098       host                  1.2.0                 USB      64     GET DESCRIPTOR Request DEVICE
      8 0.015218       1.2.0                 host                  USB      82     GET DESCRIPTOR Response DEVICE
      9 0.015272       host                  1.2.0                 USB      64     GET DESCRIPTOR Request CONFIGURATION
     10 0.017966       1.2.0                 host                  USB      73     GET DESCRIPTOR Response CONFIGURATION
     11 0.018020       host                  1.2.0                 USB      64     GET DESCRIPTOR Request CONFIGURATION
     12 0.025965       1.2.0                 host                  USB      425    GET DESCRIPTOR Response CONFIGURATION
     23 2.482241       host                  1.2.0                 USB      64     GET DESCRIPTOR Request STRING
     24 2.484931       1.2.0                 host                  USB      98     GET DESCRIPTOR Response STRING
     25 2.484939       host                  1.2.0                 USB      64     GET DESCRIPTOR Request STRING
     26 2.487916       1.2.0                 host                  USB      84     GET DESCRIPTOR Response STRING
     27 2.487941       host                  1.2.0                 USBAUDIO 65     SET CUR CX_CLOCK_SELECTOR_CONTROL request
   2047 7.661154       1.2.0                 host                  USBAUDIO 64     SET CUR CX_CLOCK_SELECTOR_CONTROL status
   2048 7.661197       host                  1.2.0                 USBAUDIO 64     GET RANGE CS_SAM_FREQ_CONTROL request
   4097 12.781553      1.2.0                 host                  USBAUDIO 64     GET RANGE CS_SAM_FREQ_CONTROL[Malformed Packet]

The first discrepancy can be found in the URB status field of packet no. 2047 (vs. 74 below) which is -2: No such file or directory (- ENOENT).
In the second (following) case where the sound device initializes okay, the URB status of the similar packet is Success (0) instead:

No.     Time           Source                Destination           Protocol Length Info
      7 0.011565       host                  1.2.0                 USB      64     GET DESCRIPTOR Request DEVICE
      8 0.015471       1.2.0                 host                  USB      82     GET DESCRIPTOR Response DEVICE
      9 0.015523       host                  1.2.0                 USB      64     GET DESCRIPTOR Request CONFIGURATION
     10 0.018477       1.2.0                 host                  USB      73     GET DESCRIPTOR Response CONFIGURATION
     11 0.018537       host                  1.2.0                 USB      64     GET DESCRIPTOR Request CONFIGURATION
     12 0.026331       1.2.0                 host                  USB      425    GET DESCRIPTOR Response CONFIGURATION
     23 4.168190       host                  1.2.0                 USB      64     GET DESCRIPTOR Request STRING
     24 4.171031       1.2.0                 host                  USB      98     GET DESCRIPTOR Response STRING
     25 4.171040       host                  1.2.0                 USB      64     GET DESCRIPTOR Request STRING
     26 4.174021       1.2.0                 host                  USB      84     GET DESCRIPTOR Response STRING
     27 4.174041       host                  1.2.0                 USBAUDIO 65     SET CUR CX_CLOCK_SELECTOR_CONTROL request
     74 4.476033       1.2.0                 host                  USBAUDIO 64     SET CUR CX_CLOCK_SELECTOR_CONTROL status
     75 4.476050       host                  1.2.0                 USBAUDIO 64     GET CUR CX_CLOCK_SELECTOR_CONTROL request
     76 4.479034       1.2.0                 host                  USBAUDIO 65     GET CUR CX_CLOCK_SELECTOR_CONTROL response
     77 4.479050       host                  1.2.0                 USBAUDIO 64     GET RANGE CS_SAM_FREQ_CONTROL request
    202 4.582043       1.2.0                 host                  USBAUDIO 66     GET RANGE CS_SAM_FREQ_CONTROL response

Please ask, if I should provide any more information or how and to whom I can provide the full USB captures.

Thank you,
Ben

#4 lore raw
Quoted 202 lines · Benedikt Ziemons
Quoted 81 lines · Luiz Augusto von Dentz

Hi Chris, Sean, Hao,

Quoted 77 lines · Geraldo Nascimento
Quoted 33 lines · Geoffrey D. Bennett

This series (choose 1 of the 2 patches) addresses an issue where the
MT7922 Bluetooth controller reset added in commit ccfc8948d7e4 ("Bluetooth: btusb: mediatek: reset the controller before downloading
the fw") is causing Focusrite USB audio devices to fail to initialise
when connected during boot on kernels 6.11 and newer.

Reported by three users here:
https://github.com/geoffreybennett/linux-fcp/issues/24

Two users confirmed they have an MT7922.

I'm providing two possible solutions as I note there was a similar
change made in commit a7208610761a ("Bluetooth: btmtk: Remove resetting mt7921 before downloading the fw"), so I'm not sure if the
reset should be reverted for the MT7925 as well as the MT7922.

Option 1: Revert the problematic reset behaviour entirely (MT7922 +
MT7925)

Option 2: Remove the reset only for the MT7922

Geoffrey D. Bennett (2):

  [PATCH 1/2] Revert "Bluetooth: btusb: mediatek: reset the controller
    before downloading the fw"

Quoted 7 lines

  [PATCH 2/2] Bluetooth: btmtk: Remove resetting mt7922 before downloading the fw

--
2.45.0

Hi Geoffrey,

I understand there's no apparent nexus of causality here.

However if three different users suddenly reported the same problem and
the fix fixes it, we should take the report seriously and back down on the problematic commit until we figure for sure what the heck is going on.

My bet is this is bona fide bug in the USB subsystem, but either I'm not
looking hard enough or I'm looking into the wrong places, because there's no way I can see in which way USB bluetooth driver from MediaTek could cause clock detection to fail.

No point in pressing this harder, but yeah, take the reports more than
seriously, because if we don't understand in which way our own (Linux)
code could be causing this, at least we should take cautionary measures.

In that sense, putting Takashi Iwai and Greg KH to Cc: in a modest but
sincere belief that this issue is more than real, even though it looks
like anticipated April 1st. Takashi can help with his expertise in clock
detection and Greg could help pinpoint if this is indeed madness in the
USB subsystem.

Quoted 7 lines
Quoted 1 line

Hope you and them don't mind the escalation :)

Do you guys have any idea what could be possibly going on here? There really seems something is not right if one driver affects the other, especially if the devices are not actually related in any way.

Hello everyone,

I did the kernel bisection on this issue and tested Geoffrey's patches since I own the affected combination of hardware and can reliably reproduce the issue.

I was now able to capture both the sound device initialization failure and the successful initialization from initramfs using the usbmon module. One difference that is immediately noticeable is the amount of URB_CONTROL data that is sent to the mediatek btusb device and a considerable slow-down of the boot process (around 16s difference).

Following is some more information about the timing and other related messages from the kernel message log. The first excerpt is from an unpatched kernel 6.14.0-rc5:

[   59.987242] lunar kernel: usb 1-2: new high-speed USB device number 2 using xhci_hcd
[   59.987975] lunar kernel: usb 1-2: New USB device found, idVendor=1235, idProduct=8212, bcdDevice= 6.45
[   59.988048] lunar kernel: usb 1-2: New USB device strings: Mfr=1, Product=3, SerialNumber=2
[   59.988121] lunar kernel: usb 1-2: Product: Scarlett 4i4 USB
[   59.988197] lunar kernel: usb 1-2: Manufacturer: Focusrite
[   60.571193] lunar kernel: mt7921e 0000:0a:00.0: enabling device (0000 -> 0002)
[   60.571314] lunar kernel: mt7921e 0000:0a:00.0: ASIC revision: 79220010
[   60.571501] lunar kernel: usbcore: registered new interface driver btusb
[   60.571513] lunar kernel: mt7921e 0000:0a:00.0: HW/SW Version: 0x8a108a10, Build Time: 20241106163228a
[   60.571627] lunar kernel: mt7921e 0000:0a:00.0: WM Firmware Version: ____000000, Build Time: 20241106163310
[   60.616673] lunar kernel: Bluetooth: hci0: HW/SW Version: 0x008a008a, Build Time: 20241106163512
[   64.549017] lunar kernel: mt7921e 0000:0a:00.0 wlp10s0: renamed from wlan0
[   70.700407] lunar kernel: usb 1-2: parse_audio_format_rates_v2v3(): unable to retrieve number of sample rates (clock 41)
[   81.264360] lunar kernel: usb 1-2: parse_audio_format_rates_v2v3(): unable to retrieve number of sample rates (clock 41)
[   81.264611] lunar kernel: usb 1-2: Focusrite Scarlett Gen 3 Mixer Driver enabled (pid=0x8212); report any issues to https://github.com/geoffreybennett/scarlett-gen2/issues
[   81.264782] lunar kernel: usb 1-2: Error initialising Scarlett Gen 3 Mixer Driver: -71
[   81.264903] lunar kernel: snd-usb-audio 1-2:1.0: probe with driver snd-usb-audio failed with error -71
[   81.265040] lunar kernel: usb 1-2: Quirk or no altset; falling back to MIDI 1.0
[   81.400030] lunar kernel: Bluetooth: hci0: Device setup in 20435397 usecs
[   81.400114] lunar kernel: Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported.
[   81.680052] lunar kernel: Bluetooth: hci0: AOSP extensions version v1.00
[   81.680170] lunar kernel: Bluetooth: hci0: AOSP quality report is supported
[   87.373353] lunar kernel: usbcore: registered new interface driver snd-usb-audio

The following second excerpt is from the same kernel version with Geoffrey's second patch applied:

[  139.603887] lunar kernel: usb 1-2: new high-speed USB device number 2 using xhci_hcd
[  139.604524] lunar kernel: usb 1-2: New USB device found, idVendor=1235, idProduct=8212, bcdDevice= 6.45
[  139.604598] lunar kernel: usb 1-2: New USB device strings: Mfr=1, Product=3, SerialNumber=2
[  139.604672] lunar kernel: usb 1-2: Product: Scarlett 4i4 USB
[  139.604744] lunar kernel: usb 1-2: Manufacturer: Focusrite
[  140.192488] lunar kernel: usbcore: registered new interface driver btusb
[  140.192501] lunar kernel: mt7921e 0000:0a:00.0: enabling device (0000 -> 0002)
[  140.192627] lunar kernel: Bluetooth: hci0: HW/SW Version: 0x008a008a, Build Time: 20241106163512
[  140.192639] lunar kernel: mt7921e 0000:0a:00.0: ASIC revision: 79220010
[  140.192753] lunar kernel: mt7921e 0000:0a:00.0: HW/SW Version: 0x8a108a10, Build Time: 20241106163228a
[  140.192866] lunar kernel: mt7921e 0000:0a:00.0: WM Firmware Version: ____000000, Build Time: 20241106163310
[  140.240011] lunar kernel: Bluetooth: hci0: Device setup in 188119 usecs
[  140.240048] lunar kernel: Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported.
[  140.513341] lunar kernel: Bluetooth: hci0: AOSP extensions version v1.00
[  140.513379] lunar kernel: Bluetooth: hci0: AOSP quality report is supported
[  144.115475] lunar kernel: mt7921e 0000:0a:00.0 wlp10s0: renamed from wlan0
[  144.115747] lunar kernel: usb 1-2: Focusrite Scarlett Gen 3 Mixer Driver enabled (pid=0x8212); report any issues to https://github.com/geoffreybennett/scarlett-gen2/issues
[  144.115857] lunar kernel: usb 1-2: Firmware version 1605
[  144.115954] lunar kernel: usb 1-2: Quirk or no altset; falling back to MIDI 1.0
[  147.843340] lunar kernel: usbcore: registered new interface driver snd-usb-audio

Comparing the USB captures from the hub, filtered to just the first few messages of the audio device yield the following exchanges. Again, first the broken case:

No.     Time           Source                Destination           Protocol Length Info
      7 0.011098       host                  1.2.0                 USB      64     GET DESCRIPTOR Request DEVICE
      8 0.015218       1.2.0                 host                  USB      82     GET DESCRIPTOR Response DEVICE
      9 0.015272       host                  1.2.0                 USB      64     GET DESCRIPTOR Request CONFIGURATION
     10 0.017966       1.2.0                 host                  USB      73     GET DESCRIPTOR Response CONFIGURATION
     11 0.018020       host                  1.2.0                 USB      64     GET DESCRIPTOR Request CONFIGURATION
     12 0.025965       1.2.0                 host                  USB      425    GET DESCRIPTOR Response CONFIGURATION
     23 2.482241       host                  1.2.0                 USB      64     GET DESCRIPTOR Request STRING
     24 2.484931       1.2.0                 host                  USB      98     GET DESCRIPTOR Response STRING
     25 2.484939       host                  1.2.0                 USB      64     GET DESCRIPTOR Request STRING
     26 2.487916       1.2.0                 host                  USB      84     GET DESCRIPTOR Response STRING
     27 2.487941       host                  1.2.0                 USBAUDIO 65     SET CUR CX_CLOCK_SELECTOR_CONTROL request
   2047 7.661154       1.2.0                 host                  USBAUDIO 64     SET CUR CX_CLOCK_SELECTOR_CONTROL status
   2048 7.661197       host                  1.2.0                 USBAUDIO 64     GET RANGE CS_SAM_FREQ_CONTROL request
   4097 12.781553      1.2.0                 host                  USBAUDIO 64     GET RANGE CS_SAM_FREQ_CONTROL[Malformed Packet]

The first discrepancy can be found in the URB status field of packet no. 2047 (vs. 74 below) which is -2: No such file or directory (- ENOENT).
In the second (following) case where the sound device initializes okay, the URB status of the similar packet is Success (0) instead:

No.     Time           Source                Destination           Protocol Length Info
      7 0.011565       host                  1.2.0                 USB      64     GET DESCRIPTOR Request DEVICE
      8 0.015471       1.2.0                 host                  USB      82     GET DESCRIPTOR Response DEVICE
      9 0.015523       host                  1.2.0                 USB      64     GET DESCRIPTOR Request CONFIGURATION
     10 0.018477       1.2.0                 host                  USB      73     GET DESCRIPTOR Response CONFIGURATION
     11 0.018537       host                  1.2.0                 USB      64     GET DESCRIPTOR Request CONFIGURATION
     12 0.026331       1.2.0                 host                  USB      425    GET DESCRIPTOR Response CONFIGURATION
     23 4.168190       host                  1.2.0                 USB      64     GET DESCRIPTOR Request STRING
     24 4.171031       1.2.0                 host                  USB      98     GET DESCRIPTOR Response STRING
     25 4.171040       host                  1.2.0                 USB      64     GET DESCRIPTOR Request STRING
     26 4.174021       1.2.0                 host                  USB      84     GET DESCRIPTOR Response STRING
     27 4.174041       host                  1.2.0                 USBAUDIO 65     SET CUR CX_CLOCK_SELECTOR_CONTROL request
     74 4.476033       1.2.0                 host                  USBAUDIO 64     SET CUR CX_CLOCK_SELECTOR_CONTROL status
     75 4.476050       host                  1.2.0                 USBAUDIO 64     GET CUR CX_CLOCK_SELECTOR_CONTROL request
     76 4.479034       1.2.0                 host                  USBAUDIO 65     GET CUR CX_CLOCK_SELECTOR_CONTROL response
     77 4.479050       host                  1.2.0                 USBAUDIO 64     GET RANGE CS_SAM_FREQ_CONTROL request
    202 4.582043       1.2.0                 host                  USBAUDIO 66     GET RANGE CS_SAM_FREQ_CONTROL response
Quoted 5 lines

Please ask, if I should provide any more information or how and to whom I can provide the full USB captures.

Thank you,
Ben

Hi Ben,

This bit sticks out to me:

Quoted 1 line
[   81.400030] lunar kernel: Bluetooth: hci0: Device setup in 20435397 usecs

20 seconds to initialise bluetooth, vs. 188ms when not doing the reset:

Quoted 1 line
[  140.240011] lunar kernel: Bluetooth: hci0: Device setup in 188119 usecs

Does it still take 20 seconds when the Scarlett is not plugged in at boot time?

I presume lsusb -t shows both devices on the same USB bus?

Thanks,
Geoffrey.

#5 lore raw

Hi Geoffrey,

Quoted 316 lines · Geoffrey D. Bennett
Quoted 301 lines · Benedikt Ziemons
Quoted 97 lines · Luiz Augusto von Dentz

Hi Chris, Sean, Hao,

Quoted 93 lines · Geraldo Nascimento
Quoted 38 lines · Geoffrey D. Bennett

This series (choose 1 of the 2 patches) addresses an issue where
the
MT7922 Bluetooth controller reset added in commit ccfc8948d7e4
("Bluetooth: btusb: mediatek: reset the controller before downloading
the fw") is causing Focusrite USB audio devices to fail to initialise
when connected during boot on kernels 6.11 and newer.

Reported by three users here:
https://github.com/geoffreybennett/linux-fcp/issues/24

Two users confirmed they have an MT7922.

I'm providing two possible solutions as I note there was a similar
change made in commit a7208610761a ("Bluetooth: btmtk: Remove resetting mt7921 before downloading the fw"), so I'm not sure if
the
reset should be reverted for the MT7925 as well as the MT7922.

Option 1: Revert the problematic reset behaviour entirely (MT7922
+
MT7925)

Option 2: Remove the reset only for the MT7922

Geoffrey D. Bennett (2):

  [PATCH 1/2] Revert "Bluetooth: btusb: mediatek: reset the controller
    before downloading the fw"

Quoted 8 lines

  [PATCH 2/2] Bluetooth: btmtk: Remove resetting mt7922 before
    downloading the fw

--
2.45.0

Hi Geoffrey,

I understand there's no apparent nexus of causality here.

However if three different users suddenly reported the same problem
and
the fix fixes it, we should take the report seriously and back down
on the problematic commit until we figure for sure what the heck is
going on.

My bet is this is bona fide bug in the USB subsystem, but either
I'm not
looking hard enough or I'm looking into the wrong places, because
there's no way I can see in which way USB bluetooth driver from MediaTek could cause clock detection to fail.

No point in pressing this harder, but yeah, take the reports more
than
seriously, because if we don't understand in which way our own (Linux)
code could be causing this, at least we should take cautionary measures.

In that sense, putting Takashi Iwai and Greg KH to Cc: in a modest
but
sincere belief that this issue is more than real, even though it
looks
like anticipated April 1st. Takashi can help with his expertise in
clock
detection and Greg could help pinpoint if this is indeed madness in
the
USB subsystem.

Quoted 9 lines
Quoted 1 line

Hope you and them don't mind the escalation :)

Do you guys have any idea what could be possibly going on here? There
really seems something is not right if one driver affects the other,
especially if the devices are not actually related in any way.

Hello everyone,

I did the kernel bisection on this issue and tested Geoffrey's patches
since I own the affected combination of hardware and can reliably reproduce the issue.

I was now able to capture both the sound device initialization failure
and the successful initialization from initramfs using the usbmon module. One difference that is immediately noticeable is the amount of
URB_CONTROL data that is sent to the mediatek btusb device and a considerable slow-down of the boot process (around 16s difference).

Following is some more information about the timing and other related
messages from the kernel message log. The first excerpt is from an unpatched kernel 6.14.0-rc5:

[   59.987242] lunar kernel: usb 1-2: new high-speed USB device number 2 using xhci_hcd
[   59.987975] lunar kernel: usb 1-2: New USB device found, idVendor=1235, idProduct=8212, bcdDevice= 6.45
[   59.988048] lunar kernel: usb 1-2: New USB device strings:
Mfr=1, Product=3, SerialNumber=2
[   59.988121] lunar kernel: usb 1-2: Product: Scarlett 4i4 USB [   59.988197] lunar kernel: usb 1-2: Manufacturer: Focusrite [   60.571193] lunar kernel: mt7921e 0000:0a:00.0: enabling device (0000 -> 0002)
[   60.571314] lunar kernel: mt7921e 0000:0a:00.0: ASIC revision:
79220010
[   60.571501] lunar kernel: usbcore: registered new interface driver btusb
[   60.571513] lunar kernel: mt7921e 0000:0a:00.0: HW/SW Version:
0x8a108a10, Build Time: 20241106163228a
[   60.571627] lunar kernel: mt7921e 0000:0a:00.0: WM Firmware
Version: ____000000, Build Time: 20241106163310
[   60.616673] lunar kernel: Bluetooth: hci0: HW/SW Version:
0x008a008a, Build Time: 20241106163512
[   64.549017] lunar kernel: mt7921e 0000:0a:00.0 wlp10s0: renamed from wlan0
[   70.700407] lunar kernel: usb 1-2:
parse_audio_format_rates_v2v3(): unable to retrieve number of sample rates (clock 41)
[   81.264360] lunar kernel: usb 1-2:
parse_audio_format_rates_v2v3(): unable to retrieve number of sample rates (clock 41)
[   81.264611] lunar kernel: usb 1-2: Focusrite Scarlett Gen 3 Mixer Driver enabled (pid=0x8212); report any issues to
https://github.com/geoffreybennett/scarlett-gen2/issues
[   81.264782] lunar kernel: usb 1-2: Error initialising Scarlett Gen 3 Mixer Driver: -71
[   81.264903] lunar kernel: snd-usb-audio 1-2:1.0: probe with driver snd-usb-audio failed with error -71
[   81.265040] lunar kernel: usb 1-2: Quirk or no altset; falling back to MIDI 1.0
[   81.400030] lunar kernel: Bluetooth: hci0: Device setup in 20435397 usecs
[   81.400114] lunar kernel: Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported. [   81.680052] lunar kernel: Bluetooth: hci0: AOSP extensions version v1.00
[   81.680170] lunar kernel: Bluetooth: hci0: AOSP quality report is supported
[   87.373353] lunar kernel: usbcore: registered new interface driver snd-usb-audio

The following second excerpt is from the same kernel version with Geoffrey's second patch applied:

[  139.603887] lunar kernel: usb 1-2: new high-speed USB device number 2 using xhci_hcd
[  139.604524] lunar kernel: usb 1-2: New USB device found, idVendor=1235, idProduct=8212, bcdDevice= 6.45
[  139.604598] lunar kernel: usb 1-2: New USB device strings:
Mfr=1, Product=3, SerialNumber=2
[  139.604672] lunar kernel: usb 1-2: Product: Scarlett 4i4 USB [  139.604744] lunar kernel: usb 1-2: Manufacturer: Focusrite [  140.192488] lunar kernel: usbcore: registered new interface driver btusb
[  140.192501] lunar kernel: mt7921e 0000:0a:00.0: enabling device (0000 -> 0002)
[  140.192627] lunar kernel: Bluetooth: hci0: HW/SW Version:
0x008a008a, Build Time: 20241106163512
[  140.192639] lunar kernel: mt7921e 0000:0a:00.0: ASIC revision:
79220010
[  140.192753] lunar kernel: mt7921e 0000:0a:00.0: HW/SW Version:
0x8a108a10, Build Time: 20241106163228a
[  140.192866] lunar kernel: mt7921e 0000:0a:00.0: WM Firmware
Version: ____000000, Build Time: 20241106163310
[  140.240011] lunar kernel: Bluetooth: hci0: Device setup in 188119 usecs
[  140.240048] lunar kernel: Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported. [  140.513341] lunar kernel: Bluetooth: hci0: AOSP extensions version v1.00
[  140.513379] lunar kernel: Bluetooth: hci0: AOSP quality report is supported
[  144.115475] lunar kernel: mt7921e 0000:0a:00.0 wlp10s0: renamed from wlan0
[  144.115747] lunar kernel: usb 1-2: Focusrite Scarlett Gen 3 Mixer Driver enabled (pid=0x8212); report any issues to
https://github.com/geoffreybennett/scarlett-gen2/issues
[  144.115857] lunar kernel: usb 1-2: Firmware version 1605 [  144.115954] lunar kernel: usb 1-2: Quirk or no altset; falling back to MIDI 1.0
[  147.843340] lunar kernel: usbcore: registered new interface driver snd-usb-audio

Comparing the USB captures from the hub, filtered to just the first few
messages of the audio device yield the following exchanges. Again, first the broken case:

No.     Time           Source                Destination Protocol Length Info
      7 0.011098       host                  1.2.0 USB      64     GET DESCRIPTOR Request DEVICE
      8 0.015218       1.2.0                 host
USB      82     GET DESCRIPTOR Response DEVICE
      9 0.015272       host                  1.2.0 USB      64     GET DESCRIPTOR Request CONFIGURATION 10 0.017966       1.2.0                 host
USB      73     GET DESCRIPTOR Response CONFIGURATION 11 0.018020       host                  1.2.0 USB      64     GET DESCRIPTOR Request CONFIGURATION 12 0.025965       1.2.0                 host
USB      425    GET DESCRIPTOR Response CONFIGURATION 23 2.482241       host                  1.2.0 USB      64     GET DESCRIPTOR Request STRING
     24 2.484931       1.2.0                 host
USB      98     GET DESCRIPTOR Response STRING
     25 2.484939       host                  1.2.0 USB      64     GET DESCRIPTOR Request STRING
     26 2.487916       1.2.0                 host
USB      84     GET DESCRIPTOR Response STRING
     27 2.487941       host                  1.2.0 USBAUDIO 65     SET CUR CX_CLOCK_SELECTOR_CONTROL request 2047 7.661154       1.2.0                 host USBAUDIO 64     SET CUR CX_CLOCK_SELECTOR_CONTROL status 2048 7.661197       host                  1.2.0 USBAUDIO 64     GET RANGE CS_SAM_FREQ_CONTROL request 4097 12.781553      1.2.0                 host USBAUDIO 64     GET RANGE CS_SAM_FREQ_CONTROL[Malformed Packet]

The first discrepancy can be found in the URB status field of packet
no. 2047 (vs. 74 below) which is -2: No such file or directory (- ENOENT).
In the second (following) case where the sound device initializes okay,
the URB status of the similar packet is Success (0) instead:

No.     Time           Source                Destination Protocol Length Info
      7 0.011565       host                  1.2.0 USB      64     GET DESCRIPTOR Request DEVICE
      8 0.015471       1.2.0                 host USB      82     GET DESCRIPTOR Response DEVICE
      9 0.015523       host                  1.2.0 USB      64     GET DESCRIPTOR Request CONFIGURATION 10 0.018477       1.2.0                 host USB      73     GET DESCRIPTOR Response CONFIGURATION 11 0.018537       host                  1.2.0 USB      64     GET DESCRIPTOR Request CONFIGURATION 12 0.026331       1.2.0                 host USB      425    GET DESCRIPTOR Response CONFIGURATION 23 4.168190       host                  1.2.0 USB      64     GET DESCRIPTOR Request STRING
     24 4.171031       1.2.0                 host USB      98     GET DESCRIPTOR Response STRING
     25 4.171040       host                  1.2.0 USB      64     GET DESCRIPTOR Request STRING
     26 4.174021       1.2.0                 host USB      84     GET DESCRIPTOR Response STRING
     27 4.174041       host                  1.2.0 USBAUDIO 65     SET CUR CX_CLOCK_SELECTOR_CONTROL request 74 4.476033       1.2.0                 host USBAUDIO 64     SET CUR CX_CLOCK_SELECTOR_CONTROL status 75 4.476050       host                  1.2.0 USBAUDIO 64     GET CUR CX_CLOCK_SELECTOR_CONTROL request 76 4.479034       1.2.0                 host USBAUDIO 65     GET CUR CX_CLOCK_SELECTOR_CONTROL response 77 4.479050       host                  1.2.0 USBAUDIO 64     GET RANGE CS_SAM_FREQ_CONTROL request 202 4.582043       1.2.0                 host USBAUDIO 66     GET RANGE CS_SAM_FREQ_CONTROL response

Quoted 6 lines

Please ask, if I should provide any more information or how and to whom
I can provide the full USB captures.

Thank you,
Ben

Hi Ben,

This bit sticks out to me:

Quoted 2 lines

[   81.400030] lunar kernel: Bluetooth: hci0: Device setup in 20435397 usecs

Quoted 8 lines

20 seconds to initialise bluetooth, vs. 188ms when not doing the reset:

Quoted 2 lines

[  140.240011] lunar kernel: Bluetooth: hci0: Device setup in 188119 usecs

Does it still take 20 seconds when the Scarlett is not plugged in at boot time?

Yes, it still takes 20 seconds without the Scarlett plugged in. Here are kernel messages about the mediatek device in this case:

[    6.620016] lunar kernel: Bluetooth: Core ver 2.22
[    6.666695] lunar kernel: NET: Registered PF_BLUETOOTH protocol family
[    6.666756] lunar kernel: Bluetooth: HCI device and connection manager initialized
[    6.666770] lunar kernel: Bluetooth: HCI socket layer initialized
[    6.666784] lunar kernel: Bluetooth: L2CAP socket layer initialized
[    6.666794] lunar kernel: Bluetooth: SCO socket layer initialized
[    6.912392] lunar kernel: usbcore: registered new interface driver btusb
[    6.912402] lunar kernel: mt7921e 0000:0a:00.0: enabling device (0000 -> 0002)
[    6.912519] lunar kernel: mt7921e 0000:0a:00.0: ASIC revision: 79220010
[    6.912627] lunar kernel: mt7921e 0000:0a:00.0: HW/SW Version: 0x8a108a10, Build Time: 20241106163228a
[    6.912739] lunar kernel: mt7921e 0000:0a:00.0: WM Firmware Version: ____000000, Build Time: 20241106163310
[    6.912847] lunar kernel: Bluetooth: hci0: HW/SW Version: 0x008a008a, Build Time: 20241106163512
[    8.010016] lunar kernel: mt7921e 0000:0a:00.0 wlp10s0: renamed from wlan0
[   12.723353] lunar kernel: usbcore: registered new interface driver snd-usb-audio
[   27.606693] lunar kernel: Bluetooth: hci0: Device setup in 20342576 usecs
[   27.606748] lunar kernel: Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported.
[   27.883398] lunar kernel: Bluetooth: hci0: AOSP extensions version v1.00
[   27.883466] lunar kernel: Bluetooth: hci0: AOSP quality report is supported
Quoted 2 lines

I presume lsusb -t shows both devices on the same USB bus?

Yes, indeed, they are both on bus 1. For the captures I also made sure that no other devices are on the same bus.
I also just tried connecting the Scarlett to a different USB bus and cannot reproduce the original issue with this setup.

Quoted 3 lines

Thanks,
Geoffrey.

#6 lore raw
In reply to Benedikt Ziemons

[Cc: +regressions, commit ccfc8948d7e4 was added in v6.11-rc1]

Am 13.03.25 um 02:43 schrieb Benedikt Ziemons:

Quoted 181 lines · Luiz Augusto von Dentz
Quoted 63 lines · Geraldo Nascimento
Quoted 61 lines · Geoffrey D. Bennett
Quoted 23 lines

This series (choose 1 of the 2 patches) addresses an issue where the MT7922 Bluetooth controller reset added in commit ccfc8948d7e4 ("Bluetooth: btusb: mediatek: reset the controller before downloading the fw") is causing Focusrite USB audio devices to fail to initialise when connected during boot on kernels 6.11 and newer.

Reported by three users here:
https://github.com/geoffreybennett/linux-fcp/issues/24

Two users confirmed they have an MT7922.

I'm providing two possible solutions as I note there was a similar change made in commit a7208610761a ("Bluetooth: btmtk: Remove resetting mt7921 before downloading the fw"), so I'm not sure if the reset should be reverted for the MT7925 as well as the MT7922.

Option 1: Revert the problematic reset behaviour entirely (MT7922 + MT7925)

Option 2: Remove the reset only for the MT7922

Geoffrey D. Bennett (2):

Quoted 10 lines

  [PATCH 1/2] Revert "Bluetooth: btusb: mediatek: reset the controller before downloading the fw"

  [PATCH 2/2] Bluetooth: btmtk: Remove resetting mt7922 before downloading the fw

--
2.45.0

Hi Geoffrey,

I understand there's no apparent nexus of causality here.

However if three different users suddenly reported the same problem and the fix fixes it, we should take the report seriously and back down on the problematic commit until we figure for sure what the heck is going on.

My bet is this is bona fide bug in the USB subsystem, but either I'm not looking hard enough or I'm looking into the wrong places, because there's no way I can see in which way USB bluetooth driver from MediaTek could cause clock detection to fail.

No point in pressing this harder, but yeah, take the reports more than seriously, because if we don't understand in which way our own (Linux) code could be causing this, at least we should take cautionary measures.

In that sense, putting Takashi Iwai and Greg KH to Cc: in a modest but sincere belief that this issue is more than real, even though it looks like anticipated April 1st. Takashi can help with his expertise in clock detection and Greg could help pinpoint if this is indeed madness in the USB subsystem.

Quoted 5 lines
Quoted 1 line

Hope you and them don't mind the escalation :)

Do you guys have any idea what could be possibly going on here? There really seems something is not right if one driver affects the other, especially if the devices are not actually related in any way.

I did the kernel bisection on this issue and tested Geoffrey's patches since I own the affected combination of hardware and can reliably reproduce the issue.

I was now able to capture both the sound device initialization failure and the successful initialization from initramfs using the usbmon module. One difference that is immediately noticeable is the amount of URB_CONTROL data that is sent to the mediatek btusb device and a considerable slow-down of the boot process (around 16s difference).

Following is some more information about the timing and other related messages from the kernel message log. The first excerpt is from an unpatched kernel 6.14.0-rc5:

[   59.987242] lunar kernel: usb 1-2: new high-speed USB device number 2 using xhci_hcd
[   59.987975] lunar kernel: usb 1-2: New USB device found, idVendor=1235, idProduct=8212, bcdDevice= 6.45
[   59.988048] lunar kernel: usb 1-2: New USB device strings: Mfr=1, Product=3, SerialNumber=2
[   59.988121] lunar kernel: usb 1-2: Product: Scarlett 4i4 USB
[   59.988197] lunar kernel: usb 1-2: Manufacturer: Focusrite
[   60.571193] lunar kernel: mt7921e 0000:0a:00.0: enabling device (0000 -> 0002)
[   60.571314] lunar kernel: mt7921e 0000:0a:00.0: ASIC revision: 79220010
[   60.571501] lunar kernel: usbcore: registered new interface driver btusb
[   60.571513] lunar kernel: mt7921e 0000:0a:00.0: HW/SW Version: 0x8a108a10, Build Time: 20241106163228a
[   60.571627] lunar kernel: mt7921e 0000:0a:00.0: WM Firmware Version: ____000000, Build Time: 20241106163310
[   60.616673] lunar kernel: Bluetooth: hci0: HW/SW Version: 0x008a008a, Build Time: 20241106163512
[   64.549017] lunar kernel: mt7921e 0000:0a:00.0 wlp10s0: renamed from wlan0
[   70.700407] lunar kernel: usb 1-2: parse_audio_format_rates_v2v3(): unable to retrieve number of sample rates (clock 41)
[   81.264360] lunar kernel: usb 1-2: parse_audio_format_rates_v2v3(): unable to retrieve number of sample rates (clock 41)
[   81.264611] lunar kernel: usb 1-2: Focusrite Scarlett Gen 3 Mixer Driver enabled (pid=0x8212); report any issues to https://github.com/geoffreybennett/scarlett-gen2/issues
[   81.264782] lunar kernel: usb 1-2: Error initialising Scarlett Gen 3 Mixer Driver: -71
[   81.264903] lunar kernel: snd-usb-audio 1-2:1.0: probe with driver snd-usb-audio failed with error -71
[   81.265040] lunar kernel: usb 1-2: Quirk or no altset; falling back to MIDI 1.0
[   81.400030] lunar kernel: Bluetooth: hci0: Device setup in 20435397 usecs
[   81.400114] lunar kernel: Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported.
[   81.680052] lunar kernel: Bluetooth: hci0: AOSP extensions version v1.00
[   81.680170] lunar kernel: Bluetooth: hci0: AOSP quality report is supported
[   87.373353] lunar kernel: usbcore: registered new interface driver snd-usb-audio

The following second excerpt is from the same kernel version with Geoffrey's second patch applied:

[  139.603887] lunar kernel: usb 1-2: new high-speed USB device number 2 using xhci_hcd
[  139.604524] lunar kernel: usb 1-2: New USB device found, idVendor=1235, idProduct=8212, bcdDevice= 6.45
[  139.604598] lunar kernel: usb 1-2: New USB device strings: Mfr=1, Product=3, SerialNumber=2
[  139.604672] lunar kernel: usb 1-2: Product: Scarlett 4i4 USB
[  139.604744] lunar kernel: usb 1-2: Manufacturer: Focusrite
[  140.192488] lunar kernel: usbcore: registered new interface driver btusb
[  140.192501] lunar kernel: mt7921e 0000:0a:00.0: enabling device (0000 -> 0002)
[  140.192627] lunar kernel: Bluetooth: hci0: HW/SW Version: 0x008a008a, Build Time: 20241106163512
[  140.192639] lunar kernel: mt7921e 0000:0a:00.0: ASIC revision: 79220010
[  140.192753] lunar kernel: mt7921e 0000:0a:00.0: HW/SW Version: 0x8a108a10, Build Time: 20241106163228a
[  140.192866] lunar kernel: mt7921e 0000:0a:00.0: WM Firmware Version: ____000000, Build Time: 20241106163310
[  140.240011] lunar kernel: Bluetooth: hci0: Device setup in 188119 usecs
[  140.240048] lunar kernel: Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported.
[  140.513341] lunar kernel: Bluetooth: hci0: AOSP extensions version v1.00
[  140.513379] lunar kernel: Bluetooth: hci0: AOSP quality report is supported
[  144.115475] lunar kernel: mt7921e 0000:0a:00.0 wlp10s0: renamed from wlan0
[  144.115747] lunar kernel: usb 1-2: Focusrite Scarlett Gen 3 Mixer Driver enabled (pid=0x8212); report any issues to https://github.com/geoffreybennett/scarlett-gen2/issues
[  144.115857] lunar kernel: usb 1-2: Firmware version 1605
[  144.115954] lunar kernel: usb 1-2: Quirk or no altset; falling back to MIDI 1.0
[  147.843340] lunar kernel: usbcore: registered new interface driver snd-usb-audio

Comparing the USB captures from the hub, filtered to just the first few messages of the audio device yield the following exchanges. Again, first the broken case:

No. Time Source Destination Protocol Length Info

       7 0.011098       host                  1.2.0                 USB      64     GET DESCRIPTOR Request DEVICE
       8 0.015218       1.2.0                 host                  USB      82     GET DESCRIPTOR Response DEVICE
       9 0.015272       host                  1.2.0                 USB      64     GET DESCRIPTOR Request CONFIGURATION
      10 0.017966       1.2.0                 host                  USB      73     GET DESCRIPTOR Response CONFIGURATION
      11 0.018020       host                  1.2.0                 USB      64     GET DESCRIPTOR Request CONFIGURATION
      12 0.025965       1.2.0                 host                  USB      425    GET DESCRIPTOR Response CONFIGURATION
      23 2.482241       host                  1.2.0                 USB      64     GET DESCRIPTOR Request STRING
      24 2.484931       1.2.0                 host                  USB      98     GET DESCRIPTOR Response STRING
      25 2.484939       host                  1.2.0                 USB      64     GET DESCRIPTOR Request STRING
      26 2.487916       1.2.0                 host                  USB      84     GET DESCRIPTOR Response STRING
      27 2.487941       host                  1.2.0                 USBAUDIO 65     SET CUR CX_CLOCK_SELECTOR_CONTROL request
    2047 7.661154       1.2.0                 host                  USBAUDIO 64     SET CUR CX_CLOCK_SELECTOR_CONTROL status
    2048 7.661197       host                  1.2.0                 USBAUDIO 64     GET RANGE CS_SAM_FREQ_CONTROL request
    4097 12.781553      1.2.0                 host                  USBAUDIO 64     GET RANGE CS_SAM_FREQ_CONTROL[Malformed Packet]

The first discrepancy can be found in the URB status field of packet no. 2047 (vs. 74 below) which is -2: No such file or directory (-ENOENT). In the second (following) case where the sound device initializes okay, the URB status of the similar packet is Success (0) instead:

No. Time Source Destination Protocol Length Info

       7 0.011565       host                  1.2.0                 USB      64     GET DESCRIPTOR Request DEVICE
       8 0.015471       1.2.0                 host                  USB      82     GET DESCRIPTOR Response DEVICE
       9 0.015523       host                  1.2.0                 USB      64     GET DESCRIPTOR Request CONFIGURATION
      10 0.018477       1.2.0                 host                  USB      73     GET DESCRIPTOR Response CONFIGURATION
      11 0.018537       host                  1.2.0                 USB      64     GET DESCRIPTOR Request CONFIGURATION
      12 0.026331       1.2.0                 host                  USB      425    GET DESCRIPTOR Response CONFIGURATION
      23 4.168190       host                  1.2.0                 USB      64     GET DESCRIPTOR Request STRING
      24 4.171031       1.2.0                 host                  USB      98     GET DESCRIPTOR Response STRING
      25 4.171040       host                  1.2.0                 USB      64     GET DESCRIPTOR Request STRING
      26 4.174021       1.2.0                 host                  USB      84     GET DESCRIPTOR Response STRING
      27 4.174041       host                  1.2.0                 USBAUDIO 65     SET CUR CX_CLOCK_SELECTOR_CONTROL request
      74 4.476033       1.2.0                 host                  USBAUDIO 64     SET CUR CX_CLOCK_SELECTOR_CONTROL status
      75 4.476050       host                  1.2.0                 USBAUDIO 64     GET CUR CX_CLOCK_SELECTOR_CONTROL request
      76 4.479034       1.2.0                 host                  USBAUDIO 65     GET CUR CX_CLOCK_SELECTOR_CONTROL response
      77 4.479050       host                  1.2.0                 USBAUDIO 64     GET RANGE CS_SAM_FREQ_CONTROL request
     202 4.582043       1.2.0                 host                  USBAUDIO 66     GET RANGE CS_SAM_FREQ_CONTROL response

Please ask, if I should provide any more information or how and to whom I can provide the full USB captures.

#7 lore raw

Hi Luiz,

Sorry for the late response.

Quoted 102 lines · Paul Menzel

External email : Please do not click links or open attachments until you have verified the sender or the content.

[Cc: +regressions, commit ccfc8948d7e4 was added in v6.11-rc1]

Am 13.03.25 um 02:43 schrieb Benedikt Ziemons:

Quoted 93 lines · Luiz Augusto von Dentz
Quoted 92 lines · Geraldo Nascimento
Quoted 83 lines
Quoted 35 lines · Geoffrey D. Bennett

This series (choose 1 of the 2 patches) addresses an issue where the
MT7922 Bluetooth controller reset added in commit ccfc8948d7e4
("Bluetooth: btusb: mediatek: reset the controller before downloading
the fw") is causing Focusrite USB audio devices to fail to initialise
when connected during boot on kernels 6.11 and newer.

Reported by three users here:
https://urldefense.com/v3/__https://github.com/geoffreybennett/linux-fcp/issues/24__;!!CTRNKA9wMg0ARbw!hovfaKcQBzFKUu7X62SNU_berXiuXtSb2ndXGjAyf9WCptdz3D8jnprUqYc6b2fQE_3zrt88nGpKtJcYUCCcdA$

Two users confirmed they have an MT7922.

I'm providing two possible solutions as I note there was a similar
change made in commit a7208610761a ("Bluetooth: btmtk: Remove resetting mt7921 before downloading the fw"), so I'm not sure if the
reset should be reverted for the MT7925 as well as the MT7922.

Option 1: Revert the problematic reset behaviour entirely (MT7922 +
MT7925)

Option 2: Remove the reset only for the MT7922

Geoffrey D. Bennett (2):

   [PATCH 1/2] Revert "Bluetooth: btusb: mediatek: reset the controller
     before downloading the fw"

Quoted 8 lines

   [PATCH 2/2] Bluetooth: btmtk: Remove resetting mt7922 before
     downloading the fw

--
2.45.0

Hi Geoffrey,

I understand there's no apparent nexus of causality here.

However if three different users suddenly reported the same problem
and the fix fixes it, we should take the report seriously and back
down on the problematic commit until we figure for sure what the heck
is going on.

My bet is this is bona fide bug in the USB subsystem, but either I'm
not looking hard enough or I'm looking into the wrong places, because
there's no way I can see in which way USB bluetooth driver from MediaTek could cause clock detection to fail.

No point in pressing this harder, but yeah, take the reports more than
seriously, because if we don't understand in which way our own (Linux)
code could be causing this, at least we should take cautionary measures.

In that sense, putting Takashi Iwai and Greg KH to Cc: in a modest but
sincere belief that this issue is more than real, even though it looks
like anticipated April 1st. Takashi can help with his expertise in
clock detection and Greg could help pinpoint if this is indeed madness
in the USB subsystem.

Quoted 1 line

Hope you and them don't mind the escalation :)

Do you guys have any idea what could be possibly going on here? There
really seems something is not right if one driver affects the other,
especially if the devices are not actually related in any way.

I've discussed internally with Sean and Hao from MediaTek who submit the changes to Kernel. The original intention was to ensure controller's status is clean before Bluetooth driver doing firmware binary download when booting. However, it seems that the changes cause unexpected USB device enumeration problem at this timing with specific USB devices.

To avoid such problem, we also agree that reverting those changes would be a better choice. Thanks a lot.

Quoted 193 lines
Quoted 193 lines

I did the kernel bisection on this issue and tested Geoffrey's patches
since I own the affected combination of hardware and can reliably reproduce the issue.

I was now able to capture both the sound device initialization failure
and the successful initialization from initramfs using the usbmon module. One difference that is immediately noticeable is the amount of
URB_CONTROL data that is sent to the mediatek btusb device and a considerable slow-down of the boot process (around 16s difference).

Following is some more information about the timing and other related
messages from the kernel message log. The first excerpt is from an unpatched kernel 6.14.0-rc5:

[   59.987242] lunar kernel: usb 1-2: new high-speed USB device number 2 using xhci_hcd
[   59.987975] lunar kernel: usb 1-2: New USB device found, idVendor=1235, idProduct=8212, bcdDevice= 6.45
[   59.988048] lunar kernel: usb 1-2: New USB device strings:
Mfr=1, Product=3, SerialNumber=2
[   59.988121] lunar kernel: usb 1-2: Product: Scarlett 4i4 USB [   59.988197] lunar kernel: usb 1-2: Manufacturer: Focusrite [   60.571193] lunar kernel: mt7921e 0000:0a:00.0: enabling device (0000 -> 0002)
[   60.571314] lunar kernel: mt7921e 0000:0a:00.0: ASIC revision:
79220010
[   60.571501] lunar kernel: usbcore: registered new interface driver btusb
[   60.571513] lunar kernel: mt7921e 0000:0a:00.0: HW/SW Version:
0x8a108a10, Build Time: 20241106163228a
[   60.571627] lunar kernel: mt7921e 0000:0a:00.0: WM Firmware
Version: ____000000, Build Time: 20241106163310
[   60.616673] lunar kernel: Bluetooth: hci0: HW/SW Version:
0x008a008a, Build Time: 20241106163512
[   64.549017] lunar kernel: mt7921e 0000:0a:00.0 wlp10s0: renamed from wlan0
[   70.700407] lunar kernel: usb 1-2:
parse_audio_format_rates_v2v3(): unable to retrieve number of sample rates (clock 41)
[   81.264360] lunar kernel: usb 1-2:
parse_audio_format_rates_v2v3(): unable to retrieve number of sample rates (clock 41)
[   81.264611] lunar kernel: usb 1-2: Focusrite Scarlett Gen 3 Mixer Driver enabled (pid=0x8212); report any issues to
https://urldefense.com/v3/__https://github.com/geoffreybennett/scarlett-gen2/issues__;!!CTRNKA9wMg0ARbw!hovfaKcQBzFKUu7X62SNU_berXiuXtSb2ndXGjAyf9WCptdz3D8jnprUqYc6b2fQE_3zrt88nGpKtJe1OM82_Q$
[   81.264782] lunar kernel: usb 1-2: Error initialising Scarlett Gen 3 Mixer Driver: -71
[   81.264903] lunar kernel: snd-usb-audio 1-2:1.0: probe with driver snd-usb-audio failed with error -71
[   81.265040] lunar kernel: usb 1-2: Quirk or no altset; falling back to MIDI 1.0
[   81.400030] lunar kernel: Bluetooth: hci0: Device setup in 20435397 usecs
[   81.400114] lunar kernel: Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported. [   81.680052] lunar kernel: Bluetooth: hci0: AOSP extensions version v1.00
[   81.680170] lunar kernel: Bluetooth: hci0: AOSP quality report is supported
[   87.373353] lunar kernel: usbcore: registered new interface driver snd-usb-audio

The following second excerpt is from the same kernel version with Geoffrey's second patch applied:

[  139.603887] lunar kernel: usb 1-2: new high-speed USB device number 2 using xhci_hcd
[  139.604524] lunar kernel: usb 1-2: New USB device found, idVendor=1235, idProduct=8212, bcdDevice= 6.45
[  139.604598] lunar kernel: usb 1-2: New USB device strings:
Mfr=1, Product=3, SerialNumber=2
[  139.604672] lunar kernel: usb 1-2: Product: Scarlett 4i4 USB [  139.604744] lunar kernel: usb 1-2: Manufacturer: Focusrite [  140.192488] lunar kernel: usbcore: registered new interface driver btusb
[  140.192501] lunar kernel: mt7921e 0000:0a:00.0: enabling device (0000 -> 0002)
[  140.192627] lunar kernel: Bluetooth: hci0: HW/SW Version:
0x008a008a, Build Time: 20241106163512
[  140.192639] lunar kernel: mt7921e 0000:0a:00.0: ASIC revision:
79220010
[  140.192753] lunar kernel: mt7921e 0000:0a:00.0: HW/SW Version:
0x8a108a10, Build Time: 20241106163228a
[  140.192866] lunar kernel: mt7921e 0000:0a:00.0: WM Firmware
Version: ____000000, Build Time: 20241106163310
[  140.240011] lunar kernel: Bluetooth: hci0: Device setup in 188119 usecs
[  140.240048] lunar kernel: Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported. [  140.513341] lunar kernel: Bluetooth: hci0: AOSP extensions version v1.00
[  140.513379] lunar kernel: Bluetooth: hci0: AOSP quality report is supported
[  144.115475] lunar kernel: mt7921e 0000:0a:00.0 wlp10s0: renamed from wlan0
[  144.115747] lunar kernel: usb 1-2: Focusrite Scarlett Gen 3 Mixer Driver enabled (pid=0x8212); report any issues to
https://urldefense.com/v3/__https://github.com/geoffreybennett/scarlett-gen2/issues__;!!CTRNKA9wMg0ARbw!hovfaKcQBzFKUu7X62SNU_berXiuXtSb2ndXGjAyf9WCptdz3D8jnprUqYc6b2fQE_3zrt88nGpKtJe1OM82_Q$
[  144.115857] lunar kernel: usb 1-2: Firmware version 1605 [  144.115954] lunar kernel: usb 1-2: Quirk or no altset; falling back to MIDI 1.0
[  147.843340] lunar kernel: usbcore: registered new interface driver snd-usb-audio

Comparing the USB captures from the hub, filtered to just the first few
messages of the audio device yield the following exchanges. Again, first the broken case:

No.     Time           Source                Destination Protocol Length Info
       7 0.011098       host                  1.2.0 USB      64     GET DESCRIPTOR Request DEVICE
       8 0.015218       1.2.0                 host USB      82     GET DESCRIPTOR Response DEVICE
       9 0.015272       host                  1.2.0 USB      64     GET DESCRIPTOR Request CONFIGURATION 10 0.017966       1.2.0                 host USB      73     GET DESCRIPTOR Response CONFIGURATION 11 0.018020       host                  1.2.0 USB      64     GET DESCRIPTOR Request CONFIGURATION 12 0.025965       1.2.0                 host USB      425    GET DESCRIPTOR Response CONFIGURATION 23 2.482241       host                  1.2.0 USB      64     GET DESCRIPTOR Request STRING
      24 2.484931       1.2.0                 host USB      98     GET DESCRIPTOR Response STRING
      25 2.484939       host                  1.2.0 USB      64     GET DESCRIPTOR Request STRING
      26 2.487916       1.2.0                 host USB      84     GET DESCRIPTOR Response STRING
      27 2.487941       host                  1.2.0 USBAUDIO 65     SET CUR CX_CLOCK_SELECTOR_CONTROL request 2047 7.661154       1.2.0                 host USBAUDIO 64     SET CUR CX_CLOCK_SELECTOR_CONTROL status 2048 7.661197       host                  1.2.0 USBAUDIO 64     GET RANGE CS_SAM_FREQ_CONTROL request 4097 12.781553      1.2.0                 host USBAUDIO 64     GET RANGE CS_SAM_FREQ_CONTROL[Malformed Packet]

The first discrepancy can be found in the URB status field of packet
no. 2047 (vs. 74 below) which is -2: No such file or directory (- ENOENT).
In the second (following) case where the sound device initializes okay, the URB status of the similar packet is Success (0) instead:

No.     Time           Source                Destination Protocol Length Info
       7 0.011565       host                  1.2.0 USB      64     GET DESCRIPTOR Request DEVICE
       8 0.015471       1.2.0                 host USB      82     GET DESCRIPTOR Response DEVICE
       9 0.015523       host                  1.2.0 USB      64     GET DESCRIPTOR Request CONFIGURATION 10 0.018477       1.2.0                 host USB      73     GET DESCRIPTOR Response CONFIGURATION 11 0.018537       host                  1.2.0 USB      64     GET DESCRIPTOR Request CONFIGURATION 12 0.026331       1.2.0                 host USB      425    GET DESCRIPTOR Response CONFIGURATION 23 4.168190       host                  1.2.0 USB      64     GET DESCRIPTOR Request STRING
      24 4.171031       1.2.0                 host USB      98     GET DESCRIPTOR Response STRING
      25 4.171040       host                  1.2.0 USB      64     GET DESCRIPTOR Request STRING
      26 4.174021       1.2.0                 host USB      84     GET DESCRIPTOR Response STRING
      27 4.174041       host                  1.2.0 USBAUDIO 65     SET CUR CX_CLOCK_SELECTOR_CONTROL request 74 4.476033       1.2.0                 host USBAUDIO 64     SET CUR CX_CLOCK_SELECTOR_CONTROL status 75 4.476050       host                  1.2.0 USBAUDIO 64     GET CUR CX_CLOCK_SELECTOR_CONTROL request 76 4.479034       1.2.0                 host USBAUDIO 65     GET CUR CX_CLOCK_SELECTOR_CONTROL response 77 4.479050       host                  1.2.0 USBAUDIO 64     GET RANGE CS_SAM_FREQ_CONTROL request 202 4.582043       1.2.0                 host USBAUDIO 66     GET RANGE CS_SAM_FREQ_CONTROL response

Please ask, if I should provide any more information or how and to whom
I can provide the full USB captures.

#8 lore raw
Quoted 115 lines · Chris Lu (陸稚泓)

Hi Luiz,

Sorry for the late response.

Quoted 102 lines · Paul Menzel

External email : Please do not click links or open attachments until you have verified the sender or the content.

[Cc: +regressions, commit ccfc8948d7e4 was added in v6.11-rc1]

Am 13.03.25 um 02:43 schrieb Benedikt Ziemons:

Quoted 93 lines · Luiz Augusto von Dentz
Quoted 92 lines · Geraldo Nascimento
Quoted 83 lines
Quoted 35 lines · Geoffrey D. Bennett

This series (choose 1 of the 2 patches) addresses an issue where the
MT7922 Bluetooth controller reset added in commit ccfc8948d7e4
("Bluetooth: btusb: mediatek: reset the controller before downloading
the fw") is causing Focusrite USB audio devices to fail to initialise
when connected during boot on kernels 6.11 and newer.

Reported by three users here:
https://urldefense.com/v3/__https://github.com/geoffreybennett/linux-fcp/issues/24__;!!CTRNKA9wMg0ARbw!hovfaKcQBzFKUu7X62SNU_berXiuXtSb2ndXGjAyf9WCptdz3D8jnprUqYc6b2fQE_3zrt88nGpKtJcYUCCcdA$

Two users confirmed they have an MT7922.

I'm providing two possible solutions as I note there was a similar
change made in commit a7208610761a ("Bluetooth: btmtk: Remove resetting mt7921 before downloading the fw"), so I'm not sure if the
reset should be reverted for the MT7925 as well as the MT7922.

Option 1: Revert the problematic reset behaviour entirely (MT7922 +
MT7925)

Option 2: Remove the reset only for the MT7922

Geoffrey D. Bennett (2):

   [PATCH 1/2] Revert "Bluetooth: btusb: mediatek: reset the controller
     before downloading the fw"

Quoted 8 lines

   [PATCH 2/2] Bluetooth: btmtk: Remove resetting mt7922 before
     downloading the fw

--
2.45.0

Hi Geoffrey,

I understand there's no apparent nexus of causality here.

However if three different users suddenly reported the same problem
and the fix fixes it, we should take the report seriously and back
down on the problematic commit until we figure for sure what the heck
is going on.

My bet is this is bona fide bug in the USB subsystem, but either I'm
not looking hard enough or I'm looking into the wrong places, because
there's no way I can see in which way USB bluetooth driver from MediaTek could cause clock detection to fail.

No point in pressing this harder, but yeah, take the reports more than
seriously, because if we don't understand in which way our own (Linux)
code could be causing this, at least we should take cautionary measures.

In that sense, putting Takashi Iwai and Greg KH to Cc: in a modest but
sincere belief that this issue is more than real, even though it looks
like anticipated April 1st. Takashi can help with his expertise in
clock detection and Greg could help pinpoint if this is indeed madness
in the USB subsystem.

Quoted 1 line

Hope you and them don't mind the escalation :)

Do you guys have any idea what could be possibly going on here? There
really seems something is not right if one driver affects the other,
especially if the devices are not actually related in any way.

I've discussed internally with Sean and Hao from MediaTek who submit the changes to Kernel. The original intention was to ensure controller's status is clean before Bluetooth driver doing firmware binary download when booting. However, it seems that the changes cause unexpected USB device enumeration problem at this timing with specific USB devices.

Quoted 2 lines

To avoid such problem, we also agree that reverting those changes would be a better choice. Thanks a lot.

Great, can someone please submit the reverts?

thanks,

greg k-h