Clarify how the usdt_prids key is stored on the BPF stack

While one can access the BPF stack relative to %r9, the whole point of DT_TRAMP_SP_SLOT(0) is to make trampoline code more readable. So use it.

Signed-off-by Eugene Loh <[email protected]>

---
 libdtrace/dt_prov_uprobe.c | 21 +++++++--------------
 1 file changed, 7 insertions(+), 14 deletions(-)

libdtrace/dt_prov_uprobe.c +7 -14

index 5d9f74244..f1323cc31 100644
@@ -1015,22 +1015,15 @@ static int trampoline(dt_pcb_t *pcb, uint_t exitlbl)
 	emit(dlp,  BPF_ALU64_IMM(BPF_RSH, BPF_REG_0, 32));
 
 	/*
-	 * Look up in the BPF 'usdt_prids' map.  Space for the look-up key
-	 * will be used on the BPF stack:
-	 *
-	 *     offset                                       value
-	 *
-	 *     -sizeof(usdt_prids_map_key_t)                pid (in %r0)
-	 *
-	 *     -sizeof(usdt_prids_map_key_t) + sizeof(pid_t)
-	 *     ==
-	 *     -sizeof(dtrace_id_t)                         underlying-probe prid
+	 * Look up in the BPF 'usdt_prids' map.  The key should fit into
+	 * trampoline stack slot 0.
 	 */
-	emit(dlp,  BPF_STORE(BPF_W, BPF_REG_9, (int)(-sizeof(usdt_prids_map_key_t)), BPF_REG_0));
-	emit(dlp,  BPF_STORE_IMM(BPF_W, BPF_REG_9, (int)(-sizeof(dtrace_id_t)), uprp->desc->id));
+	assert(sizeof(usdt_prids_map_key_t) <= DT_STK_SLOT_SZ);
+	emit(dlp,  BPF_STORE(BPF_W, BPF_REG_FP, DT_TRAMP_SP_SLOT(0), BPF_REG_0));
+	emit(dlp,  BPF_STORE_IMM(BPF_W, BPF_REG_FP, DT_TRAMP_SP_SLOT(0) + sizeof(pid_t), uprp->desc->id));
 	dt_cg_xsetx(dlp, usdt_prids, DT_LBL_NONE, BPF_REG_1, usdt_prids->di_id);
-	emit(dlp,  BPF_MOV_REG(BPF_REG_2, BPF_REG_9));
-	emit(dlp,  BPF_ALU64_IMM(BPF_ADD, BPF_REG_2, (int)(-sizeof(usdt_prids_map_key_t))));
+	emit(dlp,  BPF_MOV_REG(BPF_REG_2, BPF_REG_FP));
+	emit(dlp,  BPF_ALU64_IMM(BPF_ADD, BPF_REG_2, DT_TRAMP_SP_SLOT(0)));
 	emit(dlp,  BPF_CALL_HELPER(BPF_FUNC_map_lookup_elem));
 	emit(dlp,  BPF_BRANCH_IMM(BPF_JEQ, BPF_REG_0, 0, lbl_exit));
 

Signature · 1 line

2.43.5