mtd: nand: atmel: legacy: fix boot on USB-A9G20
Subsystems (5)
cover mtd: nand: atmel: legacy: fix boot on USB-A9G20
While trying to unbrick my Calao USB-A9G20, barebox couldn't read the NAND BB tables unlike the binary-only barebox from 2013. The first two patches fix that. The third one is a cleanup.
Happy hacking!
Wolfram Sang (3):
mtd: nand: atmel: legacy: add 'algo' to use
mtd: nand: atmel: legacy: use proper ecc_shift
mtd: nand: atmel: legacy: remove superfluous code
drivers/mtd/nand/atmel/legacy.c | 11 +++-------- 1 file changed, 3 insertions(+), 8 deletions(-)
Signature · 1 line
2.35.1
PATCH 1/3 mtd: nand: atmel: legacy: add 'algo' to use
Fixes "WARNING: Unsupported ECC algorithm!" on my USB-A9G20.
---
Or maybe we should make HAMMING the default fallback in nand_base.c?
drivers/mtd/nand/atmel/legacy.c | 4 ++++ 1 file changed, 4 insertions(+)
drivers/mtd/nand/atmel/legacy.c +4 -0
@@ -1246,6 +1246,10 @@ static int __init atmel_nand_probe(struct device *dev) nand_chip->ecc.mode =NAND_ECC_HW ; } +if (pdata->ecc_mode ==NAND_ECC_SOFT ) { + nand_chip->ecc.algo =NAND_ECC_ALGO_HAMMING ; + } + nand_chip->legacy.chip_delay =40 ;/* 40us command delay time */ if (IS_ENABLED(CONFIG_NAND_ECC_BCH) &&
Signature · 1 line
2.35.1
PATCH 2/3 mtd: nand: atmel: legacy: use proper ecc_shift
In reply to Wolfram SangThe logic of the ternary operator is broken because '1 << x' is always true even if 'x' is 0. Convert the logic to really use either the pdata value or a sane default. Fixes "WARNING: Total number of ECC bytes exceeded oobsize" on my USB-A9G20.
---
The other option is to revert babffbb193. I don't see any user. The code was obviously not enough tested as well.
drivers/mtd/nand/atmel/legacy.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/mtd/nand/atmel/legacy.c +1 -1
@@ -1240,7 +1240,7 @@ static int __init atmel_nand_probe(struct device *dev) nand_chip->ecc.mode = pdata->ecc_mode; nand_chip->ecc.strength = pdata->ecc_strength ? :1 ; - nand_chip->ecc.size =1 << pdata->ecc_size_shift ? :512 ; + nand_chip->ecc.size =1 << (pdata->ecc_size_shift ? :9 );if (pdata->ecc_mode ==NAND_ECC_HW ) { nand_chip->ecc.mode =NAND_ECC_HW ;
Signature · 1 line
2.35.1
PATCH 3/3 mtd: nand: atmel: legacy: remove superfluous code
In reply to Wolfram Sang54bccadddd always populates 'ecc_mode' but forgot to remove the code which overwrote the previously hardcoded 'NAND_ECC_SOFT' when needed. This is obsolete now.
--- drivers/mtd/nand/atmel/legacy.c | 9 --------- 1 file changed, 9 deletions(-)
drivers/mtd/nand/atmel/legacy.c +0 -9
@@ -1242,21 +1242,12 @@ static int __init atmel_nand_probe(struct device *dev) nand_chip->ecc.strength = pdata->ecc_strength ? :1 ; nand_chip->ecc.size =1 << (pdata->ecc_size_shift ? :9 ); -if (pdata->ecc_mode ==NAND_ECC_HW ) { - nand_chip->ecc.mode =NAND_ECC_HW ; - } -if (pdata->ecc_mode ==NAND_ECC_SOFT ) { nand_chip->ecc.algo =NAND_ECC_ALGO_HAMMING ; } nand_chip->legacy.chip_delay =40 ;/* 40us command delay time */ -if (IS_ENABLED (CONFIG_NAND_ECC_BCH ) && - pdata->ecc_mode ==NAND_ECC_SOFT_BCH ) { - nand_chip->ecc.mode =NAND_ECC_SOFT_BCH ; - } -if (host->board->bus_width_16) {/* 16-bit bus width */ nand_chip->options |=NAND_BUSWIDTH_16 ; nand_chip->legacy.read_buf = atmel_read_buf16;
Signature · 1 line
2.35.1
Hi Wolfram.
Quoted 3 lines · Wolfram Sang
While trying to unbrick my Calao USB-A9G20, barebox couldn't read the NAND BB tables unlike the binary-only barebox from 2013. The first two patches fix that. The third one is a cleanup.
It is only a few weeks ago I argued that there was no users of the older at91sam* boards, and then you prove me wrong here.
I will try to remember that you may be able to test should someone decide to move the barebox support for qil_a9g20 to DT and add PBL support in the process.
Sam
Hi Sam,
Quoted 2 lines
It is only a few weeks ago I argued that there was no users of the older at91sam* boards, and then you prove me wrong here.
At your service ;)
Quoted 3 lines
I will try to remember that you may be able to test should someone decide to move the barebox support for
qil_a9g20to DT and add PBL support in the process.
I am still new to at91 and barebox, but AFAICS the PBL support is only for MCI currently? I have an USB-A9G20-C01 and this one does not have SD exposed. The later version A9G20-LPW has it, but I don't own such a device, sadly. I really like the Calao USB form factor.
Happy hacking,
Wolfram
Hi Wolfram,
Nice to hear from you here ;)
Quoted 5 lines · Wolfram Sang
Hi Sam,
Quoted 2 lines
It is only a few weeks ago I argued that there was no users of the older at91sam* boards, and then you prove me wrong here.
Quoted 8 lines
At your service ;)
Quoted 3 lines
I will try to remember that you may be able to test should someone decide to move the barebox support for
qil_a9g20to DT and add PBL support in the process.I am still new to at91 and barebox, but AFAICS the PBL support is only for MCI currently?
As of 4e410f3e68280 PBL is always used on AT91.
I have no idea how the SDRAM setup is done on the USB-A9G20. There seems to be SDRAM setup code for the USB-A9263, but not for the USB-A9G20. Is there some AT91Bootstrap required?
Anyway, what's really missing is DT support. I scribbled a patch to get you started in case you are motivated. Basically it's: Compile in the device tree, throw away all the device registration from the board code, see where it gets you and fix the fallout ;)
Regards,
Sascha
---------------------------8<---------------------------
Quoted 1 line
From
9aa1026fd4a713e958e83fa3cad6875b8ce14474Mon Sep 17 00:00:00 2001
From: Sascha Hauer <[email protected]>
Date: Tue, 21 Mar 2023 09:45:41 +0100
Subject: [PATCH] usb-a9g20-dt-wip
--- arch/arm/boards/usb-a926x/init.c | 416 +----------------- .../arm/boards/usb-a926x/usb_a9260_lowlevel.c | 8 +- .../arm/boards/usb-a926x/usb_a9263_lowlevel.c | 4 +- arch/arm/configs/usb_a9g20_defconfig | 11 +- arch/arm/dts/Makefile | 3 + arch/arm/dts/usb_a9260.dts | 1 + arch/arm/dts/usb_a9263.dts | 1 + arch/arm/dts/usb_a9g20.dts | 1 + 8 files changed, 20 insertions(+), 425 deletions(-) create mode 100644 arch/arm/dts/usb_a9260.dts create mode 100644 arch/arm/dts/usb_a9263.dts create mode 100644 arch/arm/dts/usb_a9g20.dts
arch/arm/boards/usb-a926x/init.c +1 -415
@@ -5,422 +5,8 @@#include <net.h> #include <init.h> #include <environment.h> -#include <asm/armlinux.h> -#include <generated/mach-types.h> -#include <fs.h> -#include <fcntl.h> -#include <io.h> -#include <envfs.h> -#include <mach/at91/hardware.h> -#include <mach/at91/at91sam926x.h> -#include <nand.h> -#include <linux/sizes.h> -#include <linux/mtd/nand.h> -#include <linux/mtd/rawnand.h> -#include <linux/clk.h> -#include <mach/at91/board.h> -#include <mach/at91/at91sam9_smc.h> -#include <mach/at91/at91sam9_sdramc.h> -#include <gpio.h> -#include <led.h> -#include <mach/at91/iomux.h> -#include <mach/at91/at91_pmc.h> -#include <mach/at91/at91_rstc.h> -#include <gpio_keys.h> -#include <readkey.h> -#include <spi/spi.h> #include <input/input.h> - -static void usb_a9260_set_board_type (void ) -{ -if (machine_is_usb_a9g20 ()) -armlinux_set_architecture (MACH_TYPE_USB_A9G20 ); -else if (machine_is_usb_a9263 ()) -armlinux_set_architecture (MACH_TYPE_USB_A9263 ); -else -armlinux_set_architecture (MACH_TYPE_USB_A9260 ); -} - -#if defined(CONFIG_NAND_ATMEL ) -static struct atmel_nand_data nand_pdata = { - .ale =21 , - .cle =22 , - .det_pin = -EINVAL , - .rdy_pin =AT91_PIN_PC13 , - .enable_pin =AT91_PIN_PC14 , - .ecc_mode =NAND_ECC_SOFT , - .on_flash_bbt =1 , -}; - -static struct sam9_smc_config usb_a9260_nand_smc_config = { - .ncs_read_setup =0 , - .nrd_setup =1 , - .ncs_write_setup =0 , - .nwe_setup =1 , - - .ncs_read_pulse =3 , - .nrd_pulse =3 , - .ncs_write_pulse =3 , - .nwe_pulse =3 , - - .read_cycle =5 , - .write_cycle =5 , - - .mode =AT91_SMC_READMODE |AT91_SMC_WRITEMODE |AT91_SMC_EXNWMODE_DISABLE |AT91_SMC_DBW_8 , - .tdf_cycles =2 , -}; - -static struct sam9_smc_config usb_a9g20_nand_smc_config = { - .ncs_read_setup =0 , - .nrd_setup =2 , - .ncs_write_setup =0 , - .nwe_setup =2 , - - .ncs_read_pulse =4 , - .nrd_pulse =4 , - .ncs_write_pulse =4 , - .nwe_pulse =4 , - - .read_cycle =7 , - .write_cycle =7 , - - .mode =AT91_SMC_READMODE |AT91_SMC_WRITEMODE |AT91_SMC_EXNWMODE_DISABLE |AT91_SMC_DBW_8 , - .tdf_cycles =3 , -}; - -static void usb_a9260_add_device_nand (void ) -{ -/* configure chip-select 3 (NAND) */ -if (machine_is_usb_a9g20 ()) -sam9_smc_configure (0 ,3 , &usb_a9g20_nand_smc_config); -else -sam9_smc_configure (0 ,3 , &usb_a9260_nand_smc_config); - -if (machine_is_usb_a9263 ()) { - nand_pdata.rdy_pin =AT91_PIN_PA22 ; - nand_pdata.enable_pin =AT91_PIN_PD15 ; - } - -at91_add_device_nand (&nand_pdata); -} -#else -static void usb_a9260_add_device_nand (void ) {} -#endif - -#if defined(CONFIG_DRIVER_NET_MACB ) -static struct macb_platform_data macb_pdata = { - .phy_interface =PHY_INTERFACE_MODE_RMII , - .phy_addr =-1 , -}; - -static void usb_a9260_phy_reset (void ) -{ -at91_set_gpio_input (AT91_PIN_PA14 ,0 ); -at91_set_gpio_input (AT91_PIN_PA15 ,0 ); -at91_set_gpio_input (AT91_PIN_PA17 ,0 ); -at91_set_gpio_input (AT91_PIN_PA25 ,0 ); -at91_set_gpio_input (AT91_PIN_PA26 ,0 ); -at91_set_gpio_input (AT91_PIN_PA28 ,0 ); - -/* same address for the different supported SoCs */ -at91sam_phy_reset (IOMEM (AT91SAM926X_BASE_RSTC )); -} - -static void usb_a9260_add_device_eth (void ) -{ -usb_a9260_phy_reset (); -at91_add_device_eth (0 , &macb_pdata); -} -#else -static void usb_a9260_add_device_eth (void ) {} -#endif - -#if defined(CONFIG_DRIVER_SPI_ATMEL ) -static const struct spi_board_info usb_a9263_spi_devices[] = { - { - .name ="mtd_dataflash" , - .chip_select =0 , - .max_speed_hz =15 *1000 *1000 , - .bus_num =0 , - } -}; - -static const struct spi_board_info usb_a9g20_spi_devices[] = { - { - .name ="spi_mci" , - .chip_select =0 , - .max_speed_hz =25 *1000 *1000 , - .bus_num =1 , - } -}; - -static unsigned spi0_standard_cs_a9263[] = {AT91_PIN_PA5 }; -static struct at91_spi_platform_data spi_a9263_pdata = { - .chipselect = spi0_standard_cs_a9263, - .num_chipselect =ARRAY_SIZE (spi0_standard_cs_a9263), -}; - -static unsigned spi0_standard_cs_a9g20[] = {AT91_PIN_PB3 }; -static struct at91_spi_platform_data spi_a9g20_pdata = { - .chipselect = spi0_standard_cs_a9g20, - .num_chipselect =ARRAY_SIZE (spi0_standard_cs_a9g20), -}; - -static void usb_a9260_add_spi (void ) -{ -if (machine_is_usb_a9263 ()) { -spi_register_board_info (usb_a9263_spi_devices, -ARRAY_SIZE (usb_a9263_spi_devices)); -at91_add_device_spi (0 , &spi_a9263_pdata); - }else if (machine_is_usb_a9g20 () &&at91sam9260_is_low_power_sdram ()) { -spi_register_board_info (usb_a9g20_spi_devices, -ARRAY_SIZE (usb_a9g20_spi_devices)); -at91_add_device_spi (1 , &spi_a9g20_pdata); - } -} -#else -static void usb_a9260_add_spi (void ) {} -#endif - -#if defined(CONFIG_MCI_ATMEL ) -static struct atmel_mci_platform_data __initdata usb_a9260_mci_data = { - .bus_width =4 , - .detect_pin = -EINVAL , - .wp_pin = -EINVAL , -}; - -static void usb_a9260_add_device_mci (void ) -{ -at91_add_device_mci (0 , &usb_a9260_mci_data); -} -#else -static void usb_a9260_add_device_mci (void ) {} -#endif - -#if defined(CONFIG_USB_OHCI ) -static struct at91_usbh_data ek_usbh_data = { - .ports =2 , - .vbus_pin = { -EINVAL , -EINVAL }, -}; - -static void usb_a9260_add_device_usb (void ) -{ -at91_add_device_usbh_ohci (&ek_usbh_data); -} -#else -static void usb_a9260_add_device_usb (void ) {} -#endif - -#ifdef CONFIG_USB_GADGET_DRIVER_AT91 -/* -* USB Device port -*/ -static struct at91_udc_data __initdata ek_udc_data = { - .vbus_pin =AT91_PIN_PB11 , - .pullup_pin = -EINVAL ,/* pull-up driven by UDC */ -}; - -static void __init ek_add_device_udc (void ) -{ -if (machine_is_usb_a9260 () ||machine_is_usb_a9g20 ()) - ek_udc_data.vbus_pin =AT91_PIN_PC5 ; - -at91_add_device_udc (&ek_udc_data); -} -#else -static void __init ek_add_device_udc (void ) {} -#endif - -#ifdef CONFIG_LED_GPIO -struct gpio_led led = { - .gpio =AT91_PIN_PB21 , - .led = { - .name ="user_led" , - }, -}; - -static void __init ek_add_led (void ) -{ -if (machine_is_usb_a9263 ()) - led.active_low =1 ; - -at91_set_gpio_output (led.gpio, led.active_low); -led_gpio_register (&led); -} -#else -static void ek_add_led (void ) {} -#endif - -static int usb_a9260_mem_init (void ) -{ -at91_add_device_sdram (0 ); - -return 0 ; -} -mem_initcall (usb_a9260_mem_init); - -static void __init ek_add_device_button (void ) -{ -at91_set_GPIO_periph (AT91_PIN_PB10 ,1 );/* user push button, pull up enabled */ -at91_set_deglitch (AT91_PIN_PB10 ,1 ); - -export_env_ull ("dfu_button" ,AT91_PIN_PB10 ); -} - -#ifdef CONFIG_CALAO_DAB_MMX -struct gpio_led dab_mmx_leds[] = { - { - .gpio =AT91_PIN_PB20 , - .led = { - .name ="user_led1" , - }, - }, { - .gpio =AT91_PIN_PB21 , - .led = { - .name ="user_led2" , - }, - }, { - .gpio =AT91_PIN_PB22 , - .led = { - .name ="user_led3" , - }, - }, { - .gpio =AT91_PIN_PB23 , - .led = { - .name ="user_led4" , - }, - }, { - .gpio =AT91_PIN_PB24 , - .led = { - .name ="red" , - }, - }, { - .gpio =AT91_PIN_PB30 , - .led = { - .name ="orange" , - }, - }, { - .gpio =AT91_PIN_PB31 , - .led = { - .name ="green" , - }, - }, -}; - -#ifdef CONFIG_KEYBOARD_GPIO -struct gpio_keys_button keys[] = { - { - .code =KEY_UP , - .gpio =AT91_PIN_PB25 , - }, { - .code =KEY_HOME , - .gpio =AT91_PIN_PB13 , - }, { - .code =KEY_DOWN , - .gpio =AT91_PIN_PA26 , - }, { - .code =KEY_ENTER , - .gpio =AT91_PIN_PC9 , - }, -}; - -struct gpio_keys_platform_data gk_pdata = { - .buttons = keys, - .nbuttons =ARRAY_SIZE (keys), -}; - -static void usb_a9260_keyboard_device_dab_mmx (void ) -{ -int i; - -for (i =0 ; i < gk_pdata.nbuttons; i++) { -/* user push button, pull up enabled */ - keys[i].active_low =1 ; -at91_set_GPIO_periph (keys[i].gpio, keys[i].active_low); -at91_set_deglitch (keys[i].gpio,1 ); - } - -add_gpio_keys_device (DEVICE_ID_DYNAMIC , &gk_pdata); -} -#else -static void usb_a9260_keyboard_device_dab_mmx (void ) {} -#endif - -static void usb_a9260_device_dab_mmx (void ) -{ -int i; - -usb_a9260_keyboard_device_dab_mmx (); - -for (i =0 ; i <ARRAY_SIZE (dab_mmx_leds); i++) { - dab_mmx_leds[i].active_low =1 ; -at91_set_gpio_output (dab_mmx_leds[i].gpio, dab_mmx_leds[i].active_low); -led_gpio_register (&dab_mmx_leds[i]); - } -} -#else -static void usb_a9260_device_dab_mmx (void ) {} -#endif - -static int usb_a9260_devices_init (void ) -{ -usb_a9260_add_device_nand (); -usb_a9260_add_device_mci (); -usb_a9260_add_device_eth (); -usb_a9260_add_spi (); -usb_a9260_add_device_usb (); -ek_add_device_udc (); -ek_add_led (); -ek_add_device_button (); -usb_a9260_device_dab_mmx (); - -usb_a9260_set_board_type (); - -devfs_add_partition ("nand0" ,0x00000 ,SZ_128K ,DEVFS_PARTITION_FIXED ,"at91bootstrap_raw" ); -dev_add_bb_dev ("at91bootstrap_raw" ,"at91bootstrap" ); -devfs_add_partition ("nand0" ,SZ_128K ,SZ_256K ,DEVFS_PARTITION_FIXED ,"self_raw" ); -dev_add_bb_dev ("self_raw" ,"self0" ); -devfs_add_partition ("nand0" ,SZ_256K +SZ_128K ,SZ_128K ,DEVFS_PARTITION_FIXED ,"env_raw" ); -dev_add_bb_dev ("env_raw" ,"env0" ); -devfs_add_partition ("nand0" ,SZ_512K ,SZ_128K ,DEVFS_PARTITION_FIXED ,"env_raw1" ); -dev_add_bb_dev ("env_raw1" ,"env1" ); - -if (IS_ENABLED (CONFIG_DEFAULT_ENVIRONMENT_GENERIC )) -defaultenv_append_directory (defaultenv_usb_a926x); - -return 0 ; -} -device_initcall (usb_a9260_devices_init); - -#ifndef CONFIG_CONSOLE_NONE -static int usb_a9260_console_init (void ) -{ -struct device *dev; - -if (machine_is_usb_a9260 ()) { -barebox_set_model ("Calao USB-A9260" ); -barebox_set_hostname ("usb-a9260" ); - }else if (machine_is_usb_a9g20 ()) { -barebox_set_model ("Calao USB-A9G20" ); -barebox_set_hostname ("usb-a9g20" ); - }else { -barebox_set_model ("Calao USB-A9263" ); -barebox_set_hostname ("usb-a9263" ); - } - -at91_register_uart (0 ,0 ); - -if (IS_ENABLED (CONFIG_CALAO_DAB_MMX )) { -at91_register_uart (2 ,0 ); - - dev =at91_register_uart (4 ,0 ); -dev_set_param (dev,"active" ,"" ); - } - -return 0 ; -} -console_initcall (usb_a9260_console_init); -#endif +#include <mach/at91/board.h> static int usb_a9260_main_clock (void ) {
arch/arm/boards/usb-a926x/usb_a9260_lowlevel.c +6 -2
@@ -12,6 +12,8 @@#include <mach/at91/at91sam9260.h> #include <mach/at91/hardware.h> +extern char __dtb_usb_a9260_start[]; + AT91_ENTRY_FUNCTION(start_usb_a9260, r0, r1, r2) {arm_cpu_lowlevel_init ();
@@ -20,9 +22,11 @@ AT91_ENTRY_FUNCTION(start_usb_a9260, r0, r1, r2)barebox_arm_entry (AT91_CHIPSELECT_1 ,at91_get_sdram_size (IOMEM (AT91SAM9260_BASE_SDRAMC )), -NULL ); + __dtb_usb_a9260_start); } +extern char __dtb_usb_a9g20_start[]; + AT91_ENTRY_FUNCTION(start_usb_a9g20, r0, r1, r2) {arm_cpu_lowlevel_init ();
@@ -31,5 +35,5 @@ AT91_ENTRY_FUNCTION(start_usb_a9g20, r0, r1, r2)barebox_arm_entry (AT91_CHIPSELECT_1 ,at91_get_sdram_size (IOMEM (AT91SAM9260_BASE_SDRAMC )), -NULL ); + __dtb_usb_a9g20_start); }
arch/arm/boards/usb-a926x/usb_a9263_lowlevel.c +3 -1
@@ -105,6 +105,8 @@ static void __bare_init usb_a9263_board_config(struct at91sam926x_board_cfg *cfgAT91_RSTC_RSTTYP_WATCHDOG ; } +extern char __dtb_usb_a9263_start[]; + static void __bare_init usb_a9263_init(bool has_mem_128m) {struct at91sam926x_board_cfg cfg;
@@ -118,7 +120,7 @@ static void __bare_init usb_a9263_init(bool has_mem_128m)at91sam9263_board_init (&cfg);barebox_arm_entry (AT91_CHIPSELECT_1 ,at91_get_sdram_size (cfg.sdramc), -NULL ); + __dtb_usb_a9263_start); }AT91_ENTRY_FUNCTION (start_usb_a9263, r0, r1, r2)
arch/arm/configs/usb_a9g20_defconfig +4 -7
@@ -1,15 +1,13 @@ CONFIG_ARCH_AT91=y CONFIG_ARCH_AT91SAM9G20=y CONFIG_MACH_USB_A9G20=y -CONFIG_BAREBOX_MAX_IMAGE_SIZE=0x40000 CONFIG_AEABI=y CONFIG_ARM_OPTIMZED_STRING_FUNCTIONS=y -CONFIG_PBL_IMAGE=y CONFIG_MMU=y +CONFIG_BAREBOX_MAX_IMAGE_SIZE=0x40000 CONFIG_EXPERIMENTAL=y CONFIG_MALLOC_TLSF=y CONFIG_PROMPT="USB-9G20:" -CONFIG_GLOB=y CONFIG_PROMPT_HUSH_PS2="y" CONFIG_HUSH_FANCY_PROMPT=y CONFIG_CMDLINE_EDITING=y
@@ -20,7 +18,7 @@ CONFIG_BOOTM_VERBOSE=y CONFIG_BOOTM_INITRD=y CONFIG_BOOTM_OFTREE=y CONFIG_BOOTM_OFTREE_UIMAGE=y -CONFIG_CONSOLE_ACTIVATE_ALL=y +CONFIG_CONSOLE_ACTIVATE_NONE=y CONFIG_DEFAULT_ENVIRONMENT_GENERIC=y # CONFIG_CMD_ARM_CPUINFO is not set CONFIG_LONGHELP=y
@@ -58,14 +56,13 @@ CONFIG_NET=y CONFIG_NET_NFS=y CONFIG_NET_NETCONSOLE=y CONFIG_NET_RESOLV=y +CONFIG_OFDEVICE=y +CONFIG_OF_BAREBOX_DRIVERS=y CONFIG_DRIVER_NET_MACB=y CONFIG_DRIVER_SPI_ATMEL=y CONFIG_MTD=y # CONFIG_MTD_OOB_DEVICE is not set CONFIG_NAND=y -# CONFIG_NAND_ECC_HW is not set -# CONFIG_NAND_ECC_HW_SYNDROME is not set -# CONFIG_NAND_ECC_HW_NONE is not set CONFIG_NAND_ATMEL=y CONFIG_USB_GADGET=y CONFIG_USB_GADGET_DFU=y
arch/arm/dts/Makefile +3 -0
@@ -171,6 +171,9 @@ lwl-$(CONFIG_MACH_WARP7) += imx7s-warp.dtb.o lwl-$(CONFIG_MACH_VF610_TWR) += vf610-twr.dtb.o lwl-$(CONFIG_MACH_WEBASTO_CCBV2) += imx6ul-webasto-ccbv2.dtb.o lwl-$(CONFIG_MACH_WEBASTO_CCBV2) += imx6ul-webasto-marvel.dtb.o +lwl-$(CONFIG_MACH_USB_A9G20) += usb_a9g20.dtb.o +lwl-$(CONFIG_MACH_USB_A9260) += usb_a9260.dtb.o +lwl-$(CONFIG_MACH_USB_A9263) += usb_a9263.dtb.o lwl-$(CONFIG_MACH_ZII_RDU1) += \ imx51-zii-rdu1.dtb.o \ imx51-zii-scu2-mezz.dtb.o \
arch/arm/dts/usb_a9260.dts new file +1 -0
@@ -0,0 +1 @@ +#include <arm/usb_a9260.dts>
arch/arm/dts/usb_a9263.dts new file +1 -0
@@ -0,0 +1 @@ +#include <arm/usb_a9263.dts>
arch/arm/dts/usb_a9g20.dts new file +1 -0
@@ -0,0 +1 @@ +#include <arm/usb_a9g20.dts>
Signature · 8 lines
2.30.2 -- Pengutronix e.K. | | Steuerwalder Str. 21 | http://www.pengutronix.de/ | 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
Hello Sascha,
Am Tue, Mar 21, 2023 at 09:58:48AM +0100 schrieb Sascha Hauer:
Quoted 16 lines
Hi Wolfram,
Nice to hear from you here ;)
Quoted 11 lines · Wolfram Sang
Hi Sam,
Quoted 2 lines
It is only a few weeks ago I argued that there was no users of the older at91sam* boards, and then you prove me wrong here.
At your service ;)
Quoted 3 lines
I will try to remember that you may be able to test should someone decide to move the barebox support for
qil_a9g20to DT and add PBL support in the process.
Quoted 8 lines
Quoted 2 lines
I am still new to at91 and barebox, but AFAICS the PBL support is only for MCI currently?
As of
4e410f3e68280PBL is always used on AT91.I have no idea how the SDRAM setup is done on the USB-A9G20. There seems to be SDRAM setup code for the USB-A9263, but not for the USB-A9G20. Is there some AT91Bootstrap required?
I can not speak for this particular board, but for others with the same SoC (AT91SAM9G20). The vendor approach is to setup the SDRAM (and maybe more) in at91bootstrap, however those old SoCs are not supported in recent version 4.x of that anymore, 3.x should work, I never tried that for sam9g20 (we still use 1.x for those SoCs). at91bootstrap then usually loads U-Boot from flash to SDRAM and starts U-Boot.
You can do the same init in U-Boot SPL as well without the "real" at91bootstrap, I think I saw that for other boards with similar SoCs. And from what I saw here, barebox has the concept of multiple stages as well, right? So SDRAM must be initialized there in the very first stage after ROM code running from (tiny) internal SRAM, equivalent to what at91bootstrap does, before relocating to SDRAM. There's no magic thing the ROM code can do for you on that platform.
HTH & Greets
Alex
Quoted 607 lines
Anyway, what's really missing is DT support. I scribbled a patch to get you started in case you are motivated. Basically it's: Compile in the device tree, throw away all the device registration from the board code, see where it gets you and fix the fallout ;)
Regards,
Sascha---------------------------8<---------------------------
From
9aa1026fd4a713e958e83fa3cad6875b8ce14474Mon Sep 17 00:00:00 2001
From: Sascha Hauer <[email protected]>
Date: Tue, 21 Mar 2023 09:45:41 +0100
Subject: [PATCH] usb-a9g20-dt-wipSigned-off-by Sascha Hauer <[email protected]>--- arch/arm/boards/usb-a926x/init.c | 416 +----------------- .../arm/boards/usb-a926x/usb_a9260_lowlevel.c | 8 +- .../arm/boards/usb-a926x/usb_a9263_lowlevel.c | 4 +- arch/arm/configs/usb_a9g20_defconfig | 11 +- arch/arm/dts/Makefile | 3 + arch/arm/dts/usb_a9260.dts | 1 + arch/arm/dts/usb_a9263.dts | 1 + arch/arm/dts/usb_a9g20.dts | 1 + 8 files changed, 20 insertions(+), 425 deletions(-) create mode 100644 arch/arm/dts/usb_a9260.dts create mode 100644 arch/arm/dts/usb_a9263.dts create mode 100644 arch/arm/dts/usb_a9g20.dtsarch/arm/boards/usb-a926x/init.c +1
-415@@ -5,422 +5,8 @@#include <net.h> #include <init.h> #include <environment.h> -#include <asm/armlinux.h> -#include <generated/mach-types.h> -#include <fs.h> -#include <fcntl.h> -#include <io.h> -#include <envfs.h> -#include <mach/at91/hardware.h> -#include <mach/at91/at91sam926x.h> -#include <nand.h> -#include <linux/sizes.h> -#include <linux/mtd/nand.h> -#include <linux/mtd/rawnand.h> -#include <linux/clk.h> -#include <mach/at91/board.h> -#include <mach/at91/at91sam9_smc.h> -#include <mach/at91/at91sam9_sdramc.h> -#include <gpio.h> -#include <led.h> -#include <mach/at91/iomux.h> -#include <mach/at91/at91_pmc.h> -#include <mach/at91/at91_rstc.h> -#include <gpio_keys.h> -#include <readkey.h> -#include <spi/spi.h> #include <input/input.h> - -static void usb_a9260_set_board_type (void ) -{ -if (machine_is_usb_a9g20 ()) -armlinux_set_architecture (MACH_TYPE_USB_A9G20 ); -else if (machine_is_usb_a9263 ()) -armlinux_set_architecture (MACH_TYPE_USB_A9263 ); -else -armlinux_set_architecture (MACH_TYPE_USB_A9260 ); -} - -#if defined(CONFIG_NAND_ATMEL ) -static struct atmel_nand_data nand_pdata = { - .ale =21 , - .cle =22 , - .det_pin = -EINVAL , - .rdy_pin =AT91_PIN_PC13 , - .enable_pin =AT91_PIN_PC14 , - .ecc_mode =NAND_ECC_SOFT , - .on_flash_bbt =1 , -}; - -static struct sam9_smc_config usb_a9260_nand_smc_config = { - .ncs_read_setup =0 , - .nrd_setup =1 , - .ncs_write_setup =0 , - .nwe_setup =1 , - - .ncs_read_pulse =3 , - .nrd_pulse =3 , - .ncs_write_pulse =3 , - .nwe_pulse =3 , - - .read_cycle =5 , - .write_cycle =5 , - - .mode =AT91_SMC_READMODE |AT91_SMC_WRITEMODE |AT91_SMC_EXNWMODE_DISABLE |AT91_SMC_DBW_8 , - .tdf_cycles =2 , -}; - -static struct sam9_smc_config usb_a9g20_nand_smc_config = { - .ncs_read_setup =0 , - .nrd_setup =2 , - .ncs_write_setup =0 , - .nwe_setup =2 , - - .ncs_read_pulse =4 , - .nrd_pulse =4 , - .ncs_write_pulse =4 , - .nwe_pulse =4 , - - .read_cycle =7 , - .write_cycle =7 , - - .mode =AT91_SMC_READMODE |AT91_SMC_WRITEMODE |AT91_SMC_EXNWMODE_DISABLE |AT91_SMC_DBW_8 , - .tdf_cycles =3 , -}; - -static void usb_a9260_add_device_nand (void ) -{ -/* configure chip-select 3 (NAND) */ -if (machine_is_usb_a9g20 ()) -sam9_smc_configure (0 ,3 , &usb_a9g20_nand_smc_config); -else -sam9_smc_configure (0 ,3 , &usb_a9260_nand_smc_config); - -if (machine_is_usb_a9263 ()) { - nand_pdata.rdy_pin =AT91_PIN_PA22 ; - nand_pdata.enable_pin =AT91_PIN_PD15 ; - } - -at91_add_device_nand (&nand_pdata); -} -#else -static void usb_a9260_add_device_nand (void ) {} -#endif - -#if defined(CONFIG_DRIVER_NET_MACB ) -static struct macb_platform_data macb_pdata = { - .phy_interface =PHY_INTERFACE_MODE_RMII , - .phy_addr =-1 , -}; - -static void usb_a9260_phy_reset (void ) -{ -at91_set_gpio_input (AT91_PIN_PA14 ,0 ); -at91_set_gpio_input (AT91_PIN_PA15 ,0 ); -at91_set_gpio_input (AT91_PIN_PA17 ,0 ); -at91_set_gpio_input (AT91_PIN_PA25 ,0 ); -at91_set_gpio_input (AT91_PIN_PA26 ,0 ); -at91_set_gpio_input (AT91_PIN_PA28 ,0 ); - -/* same address for the different supported SoCs */ -at91sam_phy_reset (IOMEM (AT91SAM926X_BASE_RSTC )); -} - -static void usb_a9260_add_device_eth (void ) -{ -usb_a9260_phy_reset (); -at91_add_device_eth (0 , &macb_pdata); -} -#else -static void usb_a9260_add_device_eth (void ) {} -#endif - -#if defined(CONFIG_DRIVER_SPI_ATMEL ) -static const struct spi_board_info usb_a9263_spi_devices[] = { - { - .name ="mtd_dataflash" , - .chip_select =0 , - .max_speed_hz =15 *1000 *1000 , - .bus_num =0 , - } -}; - -static const struct spi_board_info usb_a9g20_spi_devices[] = { - { - .name ="spi_mci" , - .chip_select =0 , - .max_speed_hz =25 *1000 *1000 , - .bus_num =1 , - } -}; - -static unsigned spi0_standard_cs_a9263[] = {AT91_PIN_PA5 }; -static struct at91_spi_platform_data spi_a9263_pdata = { - .chipselect = spi0_standard_cs_a9263, - .num_chipselect =ARRAY_SIZE (spi0_standard_cs_a9263), -}; - -static unsigned spi0_standard_cs_a9g20[] = {AT91_PIN_PB3 }; -static struct at91_spi_platform_data spi_a9g20_pdata = { - .chipselect = spi0_standard_cs_a9g20, - .num_chipselect =ARRAY_SIZE (spi0_standard_cs_a9g20), -}; - -static void usb_a9260_add_spi (void ) -{ -if (machine_is_usb_a9263 ()) { -spi_register_board_info (usb_a9263_spi_devices, -ARRAY_SIZE (usb_a9263_spi_devices)); -at91_add_device_spi (0 , &spi_a9263_pdata); - }else if (machine_is_usb_a9g20 () &&at91sam9260_is_low_power_sdram ()) { -spi_register_board_info (usb_a9g20_spi_devices, -ARRAY_SIZE (usb_a9g20_spi_devices)); -at91_add_device_spi (1 , &spi_a9g20_pdata); - } -} -#else -static void usb_a9260_add_spi (void ) {} -#endif - -#if defined(CONFIG_MCI_ATMEL ) -static struct atmel_mci_platform_data __initdata usb_a9260_mci_data = { - .bus_width =4 , - .detect_pin = -EINVAL , - .wp_pin = -EINVAL , -}; - -static void usb_a9260_add_device_mci (void ) -{ -at91_add_device_mci (0 , &usb_a9260_mci_data); -} -#else -static void usb_a9260_add_device_mci (void ) {} -#endif - -#if defined(CONFIG_USB_OHCI ) -static struct at91_usbh_data ek_usbh_data = { - .ports =2 , - .vbus_pin = { -EINVAL , -EINVAL }, -}; - -static void usb_a9260_add_device_usb (void ) -{ -at91_add_device_usbh_ohci (&ek_usbh_data); -} -#else -static void usb_a9260_add_device_usb (void ) {} -#endif - -#ifdef CONFIG_USB_GADGET_DRIVER_AT91 -/* -* USB Device port -*/ -static struct at91_udc_data __initdata ek_udc_data = { - .vbus_pin =AT91_PIN_PB11 , - .pullup_pin = -EINVAL ,/* pull-up driven by UDC */ -}; - -static void __init ek_add_device_udc (void ) -{ -if (machine_is_usb_a9260 () ||machine_is_usb_a9g20 ()) - ek_udc_data.vbus_pin =AT91_PIN_PC5 ; - -at91_add_device_udc (&ek_udc_data); -} -#else -static void __init ek_add_device_udc (void ) {} -#endif - -#ifdef CONFIG_LED_GPIO -struct gpio_led led = { - .gpio =AT91_PIN_PB21 , - .led = { - .name ="user_led" , - }, -}; - -static void __init ek_add_led (void ) -{ -if (machine_is_usb_a9263 ()) - led.active_low =1 ; - -at91_set_gpio_output (led.gpio, led.active_low); -led_gpio_register (&led); -} -#else -static void ek_add_led (void ) {} -#endif - -static int usb_a9260_mem_init (void ) -{ -at91_add_device_sdram (0 ); - -return 0 ; -} -mem_initcall (usb_a9260_mem_init); - -static void __init ek_add_device_button (void ) -{ -at91_set_GPIO_periph (AT91_PIN_PB10 ,1 );/* user push button, pull up enabled */ -at91_set_deglitch (AT91_PIN_PB10 ,1 ); - -export_env_ull ("dfu_button" ,AT91_PIN_PB10 ); -} - -#ifdef CONFIG_CALAO_DAB_MMX -struct gpio_led dab_mmx_leds[] = { - { - .gpio =AT91_PIN_PB20 , - .led = { - .name ="user_led1" , - }, - }, { - .gpio =AT91_PIN_PB21 , - .led = { - .name ="user_led2" , - }, - }, { - .gpio =AT91_PIN_PB22 , - .led = { - .name ="user_led3" , - }, - }, { - .gpio =AT91_PIN_PB23 , - .led = { - .name ="user_led4" , - }, - }, { - .gpio =AT91_PIN_PB24 , - .led = { - .name ="red" , - }, - }, { - .gpio =AT91_PIN_PB30 , - .led = { - .name ="orange" , - }, - }, { - .gpio =AT91_PIN_PB31 , - .led = { - .name ="green" , - }, - }, -}; - -#ifdef CONFIG_KEYBOARD_GPIO -struct gpio_keys_button keys[] = { - { - .code =KEY_UP , - .gpio =AT91_PIN_PB25 , - }, { - .code =KEY_HOME , - .gpio =AT91_PIN_PB13 , - }, { - .code =KEY_DOWN , - .gpio =AT91_PIN_PA26 , - }, { - .code =KEY_ENTER , - .gpio =AT91_PIN_PC9 , - }, -}; - -struct gpio_keys_platform_data gk_pdata = { - .buttons = keys, - .nbuttons =ARRAY_SIZE (keys), -}; - -static void usb_a9260_keyboard_device_dab_mmx (void ) -{ -int i; - -for (i =0 ; i < gk_pdata.nbuttons; i++) { -/* user push button, pull up enabled */ - keys[i].active_low =1 ; -at91_set_GPIO_periph (keys[i].gpio, keys[i].active_low); -at91_set_deglitch (keys[i].gpio,1 ); - } - -add_gpio_keys_device (DEVICE_ID_DYNAMIC , &gk_pdata); -} -#else -static void usb_a9260_keyboard_device_dab_mmx (void ) {} -#endif - -static void usb_a9260_device_dab_mmx (void ) -{ -int i; - -usb_a9260_keyboard_device_dab_mmx (); - -for (i =0 ; i <ARRAY_SIZE (dab_mmx_leds); i++) { - dab_mmx_leds[i].active_low =1 ; -at91_set_gpio_output (dab_mmx_leds[i].gpio, dab_mmx_leds[i].active_low); -led_gpio_register (&dab_mmx_leds[i]); - } -} -#else -static void usb_a9260_device_dab_mmx (void ) {} -#endif - -static int usb_a9260_devices_init (void ) -{ -usb_a9260_add_device_nand (); -usb_a9260_add_device_mci (); -usb_a9260_add_device_eth (); -usb_a9260_add_spi (); -usb_a9260_add_device_usb (); -ek_add_device_udc (); -ek_add_led (); -ek_add_device_button (); -usb_a9260_device_dab_mmx (); - -usb_a9260_set_board_type (); - -devfs_add_partition ("nand0" ,0x00000 ,SZ_128K ,DEVFS_PARTITION_FIXED ,"at91bootstrap_raw" ); -dev_add_bb_dev ("at91bootstrap_raw" ,"at91bootstrap" ); -devfs_add_partition ("nand0" ,SZ_128K ,SZ_256K ,DEVFS_PARTITION_FIXED ,"self_raw" ); -dev_add_bb_dev ("self_raw" ,"self0" ); -devfs_add_partition ("nand0" ,SZ_256K +SZ_128K ,SZ_128K ,DEVFS_PARTITION_FIXED ,"env_raw" ); -dev_add_bb_dev ("env_raw" ,"env0" ); -devfs_add_partition ("nand0" ,SZ_512K ,SZ_128K ,DEVFS_PARTITION_FIXED ,"env_raw1" ); -dev_add_bb_dev ("env_raw1" ,"env1" ); - -if (IS_ENABLED (CONFIG_DEFAULT_ENVIRONMENT_GENERIC )) -defaultenv_append_directory (defaultenv_usb_a926x); - -return 0 ; -} -device_initcall (usb_a9260_devices_init); - -#ifndef CONFIG_CONSOLE_NONE -static int usb_a9260_console_init (void ) -{ -struct device *dev; - -if (machine_is_usb_a9260 ()) { -barebox_set_model ("Calao USB-A9260" ); -barebox_set_hostname ("usb-a9260" ); - }else if (machine_is_usb_a9g20 ()) { -barebox_set_model ("Calao USB-A9G20" ); -barebox_set_hostname ("usb-a9g20" ); - }else { -barebox_set_model ("Calao USB-A9263" ); -barebox_set_hostname ("usb-a9263" ); - } - -at91_register_uart (0 ,0 ); - -if (IS_ENABLED (CONFIG_CALAO_DAB_MMX )) { -at91_register_uart (2 ,0 ); - - dev =at91_register_uart (4 ,0 ); -dev_set_param (dev,"active" ,"" ); - } - -return 0 ; -} -console_initcall (usb_a9260_console_init); -#endif +#include <mach/at91/board.h> static int usb_a9260_main_clock (void ) {arch/arm/boards/usb-a926x/usb_a9260_lowlevel.c +6
-2@@ -12,6 +12,8 @@#include <mach/at91/at91sam9260.h> #include <mach/at91/hardware.h> +extern char __dtb_usb_a9260_start[]; + AT91_ENTRY_FUNCTION(start_usb_a9260, r0, r1, r2) {arm_cpu_lowlevel_init ();@@ -20,9 +22,11 @@ AT91_ENTRY_FUNCTION(start_usb_a9260, r0, r1, r2)barebox_arm_entry (AT91_CHIPSELECT_1 ,at91_get_sdram_size (IOMEM (AT91SAM9260_BASE_SDRAMC )), -NULL ); + __dtb_usb_a9260_start); } +extern char __dtb_usb_a9g20_start[]; + AT91_ENTRY_FUNCTION(start_usb_a9g20, r0, r1, r2) {arm_cpu_lowlevel_init ();@@ -31,5 +35,5 @@ AT91_ENTRY_FUNCTION(start_usb_a9g20, r0, r1, r2)barebox_arm_entry (AT91_CHIPSELECT_1 ,at91_get_sdram_size (IOMEM (AT91SAM9260_BASE_SDRAMC )), -NULL ); + __dtb_usb_a9g20_start); }arch/arm/boards/usb-a926x/usb_a9263_lowlevel.c +3
-1@@ -105,6 +105,8 @@ static void __bare_init usb_a9263_board_config(struct at91sam926x_board_cfg *cfgAT91_RSTC_RSTTYP_WATCHDOG ; } +extern char __dtb_usb_a9263_start[]; + static void __bare_init usb_a9263_init(bool has_mem_128m) {struct at91sam926x_board_cfg cfg;@@ -118,7 +120,7 @@ static void __bare_init usb_a9263_init(bool has_mem_128m)at91sam9263_board_init (&cfg);barebox_arm_entry (AT91_CHIPSELECT_1 ,at91_get_sdram_size (cfg.sdramc), -NULL ); + __dtb_usb_a9263_start); }AT91_ENTRY_FUNCTION (start_usb_a9263, r0, r1, r2)arch/arm/configs/usb_a9g20_defconfig +4
-7@@ -1,15 +1,13 @@ CONFIG_ARCH_AT91=y CONFIG_ARCH_AT91SAM9G20=y CONFIG_MACH_USB_A9G20=y -CONFIG_BAREBOX_MAX_IMAGE_SIZE=0x40000 CONFIG_AEABI=y CONFIG_ARM_OPTIMZED_STRING_FUNCTIONS=y -CONFIG_PBL_IMAGE=y CONFIG_MMU=y +CONFIG_BAREBOX_MAX_IMAGE_SIZE=0x40000 CONFIG_EXPERIMENTAL=y CONFIG_MALLOC_TLSF=y CONFIG_PROMPT="USB-9G20:" -CONFIG_GLOB=y CONFIG_PROMPT_HUSH_PS2="y" CONFIG_HUSH_FANCY_PROMPT=y CONFIG_CMDLINE_EDITING=y@@ -20,7 +18,7 @@ CONFIG_BOOTM_VERBOSE=y CONFIG_BOOTM_INITRD=y CONFIG_BOOTM_OFTREE=y CONFIG_BOOTM_OFTREE_UIMAGE=y -CONFIG_CONSOLE_ACTIVATE_ALL=y +CONFIG_CONSOLE_ACTIVATE_NONE=y CONFIG_DEFAULT_ENVIRONMENT_GENERIC=y # CONFIG_CMD_ARM_CPUINFO is not set CONFIG_LONGHELP=y@@ -58,14 +56,13 @@ CONFIG_NET=y CONFIG_NET_NFS=y CONFIG_NET_NETCONSOLE=y CONFIG_NET_RESOLV=y +CONFIG_OFDEVICE=y +CONFIG_OF_BAREBOX_DRIVERS=y CONFIG_DRIVER_NET_MACB=y CONFIG_DRIVER_SPI_ATMEL=y CONFIG_MTD=y # CONFIG_MTD_OOB_DEVICE is not set CONFIG_NAND=y -# CONFIG_NAND_ECC_HW is not set -# CONFIG_NAND_ECC_HW_SYNDROME is not set -# CONFIG_NAND_ECC_HW_NONE is not set CONFIG_NAND_ATMEL=y CONFIG_USB_GADGET=y CONFIG_USB_GADGET_DFU=yarch/arm/dts/Makefile +3
-0@@ -171,6 +171,9 @@ lwl-$(CONFIG_MACH_WARP7) += imx7s-warp.dtb.o lwl-$(CONFIG_MACH_VF610_TWR) += vf610-twr.dtb.o lwl-$(CONFIG_MACH_WEBASTO_CCBV2) += imx6ul-webasto-ccbv2.dtb.o lwl-$(CONFIG_MACH_WEBASTO_CCBV2) += imx6ul-webasto-marvel.dtb.o +lwl-$(CONFIG_MACH_USB_A9G20) += usb_a9g20.dtb.o +lwl-$(CONFIG_MACH_USB_A9260) += usb_a9260.dtb.o +lwl-$(CONFIG_MACH_USB_A9263) += usb_a9263.dtb.o lwl-$(CONFIG_MACH_ZII_RDU1) += \ imx51-zii-rdu1.dtb.o \ imx51-zii-scu2-mezz.dtb.o \arch/arm/dts/usb_a9260.dts new file +1
-0@@ -0,0 +1 @@ +#include <arm/usb_a9260.dts>arch/arm/dts/usb_a9263.dts new file +1
-0@@ -0,0 +1 @@ +#include <arm/usb_a9263.dts>arch/arm/dts/usb_a9g20.dts new file +1
-0@@ -0,0 +1 @@ +#include <arm/usb_a9g20.dts>Signature · 8 lines
2.30.2 -- Pengutronix e.K. | | Steuerwalder Str. 21 | http://www.pengutronix.de/ | 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
Hi Alexander.
Quoted 36 lines · Alexander Dahl
Hello Sascha,
Am Tue, Mar 21, 2023 at 09:58:48AM +0100 schrieb Sascha Hauer:
Quoted 16 lines
Hi Wolfram,
Nice to hear from you here ;)
Quoted 11 lines · Wolfram Sang
Hi Sam,
Quoted 2 lines
It is only a few weeks ago I argued that there was no users of the older at91sam* boards, and then you prove me wrong here.
At your service ;)
Quoted 3 lines
I will try to remember that you may be able to test should someone decide to move the barebox support for
qil_a9g20to DT and add PBL support in the process.Quoted 8 lines
Quoted 2 lines
I am still new to at91 and barebox, but AFAICS the PBL support is only for MCI currently?
As of
4e410f3e68280PBL is always used on AT91.I have no idea how the SDRAM setup is done on the USB-A9G20. There seems to be SDRAM setup code for the USB-A9263, but not for the USB-A9G20. Is there some AT91Bootstrap required?
I can not speak for this particular board, but for others with the same SoC (AT91SAM9G20). The vendor approach is to setup the SDRAM (and maybe more) in at91bootstrap, however those old SoCs are not supported in recent version 4.x of that anymore, 3.x should work, I never tried that for sam9g20 (we still use 1.x for those SoCs). at91bootstrap then usually loads U-Boot from flash to SDRAM and starts U-Boot.
Quoted 7 lines
You can do the same init in U-Boot SPL as well without the "real" at91bootstrap, I think I saw that for other boards with similar SoCs. And from what I saw here, barebox has the concept of multiple stages as well, right? So SDRAM must be initialized there in the very first stage after ROM code running from (tiny) internal SRAM, equivalent to what at91bootstrap does, before relocating to SDRAM. There's no magic thing the ROM code can do for you on that platform.
When I added support to skov-arm9cpu to use barebox as replacement for at91bootstrap the sdram init looked like this [1]:
static void sam9263_sdramc_init(unsigned int mck)
{
+ const struct at91sam9_sdramc_config config =
+ {
+ .sdramc = IOMEM(AT91SAM9263_BASE_SDRAMC0), + .mr = 0, + .tr = (mck * 7) / 1000000, // TODO 140 versus 0x13c (316)? + .cr = AT91_SDRAMC_NC_10 | AT91_SDRAMC_NR_13 | AT91_SDRAMC_CAS_2 + | AT91_SDRAMC_NB_4 | AT91_SDRAMC_DBW_32 + | AT91_SDRAMC_TWR_2 | AT91_SDRAMC_TRC_7 + | AT91_SDRAMC_TRP_2 | AT91_SDRAMC_TRCD_2 + | AT91_SDRAMC_TRAS_5 | AT91_SDRAMC_TXSR_8,
+ .lpr = 0,
+ .mdr = AT91_SDRAMC_MD_SDRAM,
+ };
+
+ /* Define PDC[31:16] as DATA[31:16] */ + at91_mux_gpio_disable(IOMEM(AT91SAM9263_BASE_PIOD), 0xffff0000); + /* No pull-up for D[31:16] */ + at91_mux_set_pullup(IOMEM(AT91SAM9263_BASE_PIOD), 0xffff0000, true); + /* PD16 to PD31 are pheripheral A */ + at91_mux_set_A_periph(IOMEM(AT91SAM9263_BASE_PIOD), 0xffff0000);
}
On my too long todo list is to complete this work and upstream this for both this and the at91sam9263ek board.
Anyway - DT support is the first step. Replacing at91bootstrap can always come later.
[1] https://lore.barebox.org/barebox/[email protected]/
Sam
Hi Sascha!
Quoted 1 line
Nice to hear from you here ;)
Yeah, it has been only 10 years... :)
Quoted 3 lines
I have no idea how the SDRAM setup is done on the USB-A9G20. There seems to be SDRAM setup code for the USB-A9263, but not for the USB-A9G20. Is there some AT91Bootstrap required?
Yes. There is a bootstrap required: https://github.com/linux4sam/at91bootstrap
However, an old version is needed. I am still fighting the details.
I accidently erased it, so my journey for unbricking the device began. at91bootstrap, openocd, barebox - they all once supported A9G20, but nowadays all of them were broken. Well, I fixed openocd and barebox mostly so far, the bootstrap is still the missing piece.
Super interesting about the A9263 setup code. I missed it so far. Does that mean that barebox can replace the at91bootstrap?
Quoted 2 lines
Anyway, what's really missing is DT support. I scribbled a patch to get you started in case you are motivated. Basically it's: Compile in the
Motivated? No way ;) Obliged? More so. But first, I want to unbrick my device. First make it work, then make it beautiful.
That being said, the two patches from this series are okay? I'd think they are still needed for other legacy systems even if I convert A9G20 to DT in some ages.
Thanks for your help!
Wolfram
Hi Wolfram.
Quoted 10 lines · Wolfram Sang
Hi Sascha!
Quoted 1 line
Nice to hear from you here ;)
Yeah, it has been only 10 years... :)
Quoted 3 lines
I have no idea how the SDRAM setup is done on the USB-A9G20. There seems to be SDRAM setup code for the USB-A9263, but not for the USB-A9G20. Is there some AT91Bootstrap required?
Quoted 7 lines
Yes. There is a bootstrap required: https://github.com/linux4sam/at91bootstrap
However, an old version is needed. I am still fighting the details.I accidently erased it, so my journey for unbricking the device began. at91bootstrap, openocd, barebox - they all once supported A9G20, but nowadays all of them were broken. Well, I fixed openocd and barebox mostly so far, the bootstrap is still the missing piece.
You may be hit by the newer gcc optimize the delays in the sdram init code in at91bootstrap.
This code:
/* Step#4 The minimum pause of 200 us is provided to precede any single toggle */
for (i = 0; i < 1000; i++) ;Are optimized away with newer gcc's.
You can find it repeated several times in the init code.
I think this was the only part what broke at91bootstrap for me. It was Ahmad, IIRC, that told me about it - so not my finding.
Quoted 3 lines
Super interesting about the A9263 setup code. I missed it so far. Does that mean that barebox can replace the at91bootstrap?
Yes. The patch series I pointed at generates a bare variant that I successfully used to boot my board direct from ROMBOOT.
It is a direct replacement for at91bootstrap and loads barebox as the next step bootloader.
I really like the way it is all integrated and how the two barebox variants are built in one go.
Sam
Quoted 14 lines
Quoted 3 lines
Anyway, what's really missing is DT support. I scribbled a patch to get you started in case you are motivated. Basically it's: Compile in the
Motivated? No way ;) Obliged? More so. But first, I want to unbrick my device. First make it work, then make it beautiful.
That being said, the two patches from this series are okay? I'd think they are still needed for other legacy systems even if I convert A9G20 to DT in some ages.
Thanks for your help!
Wolfram
Hi all.
Correcting myself here.
Quoted 7 lines
Quoted 3 lines
Super interesting about the A9263 setup code. I missed it so far. Does that mean that barebox can replace the at91bootstrap?
Yes. The patch series I pointed at generates a bare variant that I successfully used to boot my board direct from ROMBOOT.
It is a direct replacement for at91bootstrap and loads barebox as the next step bootloader.
The above is entirely correct - as the barebox variant supports booting from SD card only, where at91bootstrap support additional boot sources.
Doable, but I did not have the need, so I did not look into it.
Sam
Hi,
Quoted 4 lines
Quoted 2 lines
It is a direct replacement for at91bootstrap and loads barebox as the next step bootloader.
The above is entirely correct - as the barebox variant supports booting from SD card only, where at91bootstrap support additional boot sources.
So, I quickly built the bootstrap for A9263 and it was ~71KB in size. This is OK for the A9263 with 96KB of SRAM, but the A9G20 only has 2x16KB. So, I think I'll need to update at91bootstrap to unbrick my device. at91bootstrap is ~4-5KB from what I observed. But thanks for the inspirtation!
Happy hacking,
Wolfram
Quoted 4 lines · Wolfram Sang
Hi,
Quoted 2 lines
Quoted 2 lines
It is a direct replacement for at91bootstrap and loads barebox as the next step bootloader.
Quoted 8 lines
Quoted 2 lines
The above is entirely correct - as the barebox variant supports booting from SD card only, where at91bootstrap support additional boot sources.
So, I quickly built the bootstrap for A9263 and it was ~71KB in size. This is OK for the A9263 with 96KB of SRAM, but the A9G20 only has 2x16KB. So, I think I'll need to update at91bootstrap to unbrick my device. at91bootstrap is ~4-5KB from what I observed. But thanks for the inspirtation!
The barebox way to do that is to put an SD card driver (or whatever your bootsource is) into the PBL, then let the boot ROM just load the PBL part of the image. In the PBL configure SDRAM, use the SD card driver to load the rest of the image (or the full image again) into SDRAM and jump to it.
That might be out of scope for you right now as it requires some more work.
Sascha
Signature · 4 lines
Pengutronix e.K. | | Steuerwalder Str. 21 | http://www.pengutronix.de/ | 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
Quoted 8 lines
Quoted 5 lines
I accidently erased it, so my journey for unbricking the device began. at91bootstrap, openocd, barebox - they all once supported A9G20, but nowadays all of them were broken. Well, I fixed openocd and barebox mostly so far, the bootstrap is still the missing piece.
You may be hit by the newer gcc optimize the delays in the sdram init code in at91bootstrap.
The issue was something else: SAM-BA failed to flash the bootstrap because it couldn't get the SDRAM initialized before. I still didn't figure out why. Flashing the bootstrap with barebox never got it executed. I now found out that SAM-BA is modifying one vector at runtime before flashing. What is 'endaddress of blob in RAM' becomes 'filesize of blob'. If I modify my binary bootstrap like this, I can flash it with barebox and finally have a working device again. Phew!
Hi Sascha,
Quoted 4 lines
Anyway, what's really missing is DT support. I scribbled a patch to get you started in case you are motivated. Basically it's: Compile in the device tree, throw away all the device registration from the board code, see where it gets you and fix the fallout ;)
So, I tried this patch and if the fallout was just some errnos or devices missing, I would have fixed it. Sadly, the actual fallout is that the board doesn't boot without any printing. This needs more debugging than what I am willing to invest currently. But I can bring the device to Prague if someone from PTX wants to try.
All the best,
Wolfram
Sascha Hauer
AppliedQuoted 7 lines · Wolfram Sang
While trying to unbrick my Calao USB-A9G20, barebox couldn't read the NAND BB tables unlike the binary-only barebox from 2013. The first two patches fix that. The third one is a cleanup.
Happy hacking!
Quoted 7 lines
Wolfram Sang (3):
mtd: nand: atmel: legacy: add 'algo' to use
mtd: nand: atmel: legacy: use properecc_shift
mtd: nand: atmel: legacy: remove superfluous codedrivers/mtd/nand/atmel/legacy.c | 11 +++-------- 1 file changed, 3 insertions(+), 8 deletions(-)
Applied, thanks
Sascha
Signature · 4 lines
Pengutronix e.K. | | Steuerwalder Str. 21 | http://www.pengutronix.de/ | 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |