Problems about NIC, PCIe and usb on RK3568 EVB
Hi,
I tested Linux kernel 6.3-rc6 on my rk3568 evaluation board, it seems there are problems with Ethernet, PCIe and usb devices.
First, NICs doesn't work.
rk_gmac-dwmac fe010000.ethernet: IRQ eth_lpi not found rk_gmac-dwmac fe010000.ethernet: no regulator found rk_gmac-dwmac fe010000.ethernet: clock input or output? (output). rk_gmac-dwmac fe010000.ethernet: Can not read property: tx_delay. rk_gmac-dwmac fe010000.ethernet: set tx_delay to 0x30 rk_gmac-dwmac fe010000.ethernet: Can not read property: rx_delay. rk_gmac-dwmac fe010000.ethernet: set rx_delay to 0x10 rk_gmac-dwmac fe010000.ethernet: integrated PHY? (no). rk_gmac-dwmac fe010000.ethernet: init for RGMII_ID rk_gmac-dwmac fe010000.ethernet: User ID: 0x30, Synopsys ID: 0x51 rk_gmac-dwmac fe010000.ethernet: DWMAC4/5 rk_gmac-dwmac fe010000.ethernet: DMA HW capability register suppd rk_gmac-dwmac fe010000.ethernet: RX Checksum Offload Engine suppd rk_gmac-dwmac fe010000.ethernet: TX Checksum insertion supported rk_gmac-dwmac fe010000.ethernet: Wake-Up On Lan supported rk_gmac-dwmac fe010000.ethernet: TSO supported rk_gmac-dwmac fe010000.ethernet: Enable RX Mitigation via HW Watr rk_gmac-dwmac fe010000.ethernet: Enabled RFS Flow TC (entries=10) rk_gmac-dwmac fe010000.ethernet: TSO feature enabled rk_gmac-dwmac fe010000.ethernet: Using 32/32 bits DMA host/devich mdio_bus stmmac-1: MDIO device at address 0 is missing. rk_gmac-dwmac fe2a0000.ethernet: IRQ eth_lpi not found rk_gmac-dwmac fe2a0000.ethernet: no regulator found rk_gmac-dwmac fe2a0000.ethernet: clock input or output? (output). rk_gmac-dwmac fe2a0000.ethernet: Can not read property: tx_delay. rk_gmac-dwmac fe2a0000.ethernet: set tx_delay to 0x30 rk_gmac-dwmac fe2a0000.ethernet: Can not read property: rx_delay. rk_gmac-dwmac fe2a0000.ethernet: set rx_delay to 0x10 rk_gmac-dwmac fe2a0000.ethernet: integrated PHY? (no). rk_gmac-dwmac fe2a0000.ethernet: init for RGMII_ID rk_gmac-dwmac fe2a0000.ethernet: User ID: 0x30, Synopsys ID: 0x51 rk_gmac-dwmac fe2a0000.ethernet: DWMAC4/5 rk_gmac-dwmac fe2a0000.ethernet: DMA HW capability register suppd rk_gmac-dwmac fe2a0000.ethernet: RX Checksum Offload Engine suppd rk_gmac-dwmac fe2a0000.ethernet: TX Checksum insertion supported rk_gmac-dwmac fe2a0000.ethernet: Wake-Up On Lan supported rk_gmac-dwmac fe2a0000.ethernet: TSO supported rk_gmac-dwmac fe2a0000.ethernet: Enable RX Mitigation via HW Watr rk_gmac-dwmac fe2a0000.ethernet: Enabled RFS Flow TC (entries=10) rk_gmac-dwmac fe2a0000.ethernet: TSO feature enabled rk_gmac-dwmac fe2a0000.ethernet: Using 32/32 bits DMA host/devich mdio_bus stmmac-0: MDIO device at address 0 is missing.
rk_gmac-dwmac fe010000.ethernet eth0: Register MEM_TYPE_PAGE_POO0 rk_gmac-dwmac fe010000.ethernet eth0: __stmmac_open: Cannot atta)
Second, running 'lspci' and 'lsusb' doesn't see any devices on PCIe and USB. I guess the device tree might be updated. Anyone has idea how to fix it? Thanks.
- Doug
_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip
Hi Doug,
Quoted 56 lines · Doug Brewer
Hi,
I tested Linux kernel 6.3-rc6 on my rk3568 evaluation board, it seems there are problems with Ethernet, PCIe and usb devices.
First, NICs doesn't work.
rk_gmac-dwmac fe010000.ethernet: IRQ eth_lpi not found rk_gmac-dwmac fe010000.ethernet: no regulator found rk_gmac-dwmac fe010000.ethernet: clock input or output? (output). rk_gmac-dwmac fe010000.ethernet: Can not read property: tx_delay. rk_gmac-dwmac fe010000.ethernet: set tx_delay to 0x30 rk_gmac-dwmac fe010000.ethernet: Can not read property: rx_delay. rk_gmac-dwmac fe010000.ethernet: set rx_delay to 0x10 rk_gmac-dwmac fe010000.ethernet: integrated PHY? (no). rk_gmac-dwmac fe010000.ethernet: init for RGMII_ID rk_gmac-dwmac fe010000.ethernet: User ID: 0x30, Synopsys ID: 0x51 rk_gmac-dwmac fe010000.ethernet: DWMAC4/5 rk_gmac-dwmac fe010000.ethernet: DMA HW capability register suppd rk_gmac-dwmac fe010000.ethernet: RX Checksum Offload Engine suppd rk_gmac-dwmac fe010000.ethernet: TX Checksum insertion supported rk_gmac-dwmac fe010000.ethernet: Wake-Up On Lan supported rk_gmac-dwmac fe010000.ethernet: TSO supported rk_gmac-dwmac fe010000.ethernet: Enable RX Mitigation via HW Watr rk_gmac-dwmac fe010000.ethernet: Enabled RFS Flow TC (entries=10) rk_gmac-dwmac fe010000.ethernet: TSO feature enabled rk_gmac-dwmac fe010000.ethernet: Using 32/32 bits DMA host/devich mdio_bus stmmac-1: MDIO device at address 0 is missing. rk_gmac-dwmac fe2a0000.ethernet: IRQ eth_lpi not found rk_gmac-dwmac fe2a0000.ethernet: no regulator found rk_gmac-dwmac fe2a0000.ethernet: clock input or output? (output). rk_gmac-dwmac fe2a0000.ethernet: Can not read property: tx_delay. rk_gmac-dwmac fe2a0000.ethernet: set tx_delay to 0x30 rk_gmac-dwmac fe2a0000.ethernet: Can not read property: rx_delay. rk_gmac-dwmac fe2a0000.ethernet: set rx_delay to 0x10 rk_gmac-dwmac fe2a0000.ethernet: integrated PHY? (no). rk_gmac-dwmac fe2a0000.ethernet: init for RGMII_ID rk_gmac-dwmac fe2a0000.ethernet: User ID: 0x30, Synopsys ID: 0x51 rk_gmac-dwmac fe2a0000.ethernet: DWMAC4/5 rk_gmac-dwmac fe2a0000.ethernet: DMA HW capability register suppd rk_gmac-dwmac fe2a0000.ethernet: RX Checksum Offload Engine suppd rk_gmac-dwmac fe2a0000.ethernet: TX Checksum insertion supported rk_gmac-dwmac fe2a0000.ethernet: Wake-Up On Lan supported rk_gmac-dwmac fe2a0000.ethernet: TSO supported rk_gmac-dwmac fe2a0000.ethernet: Enable RX Mitigation via HW Watr rk_gmac-dwmac fe2a0000.ethernet: Enabled RFS Flow TC (entries=10) rk_gmac-dwmac fe2a0000.ethernet: TSO feature enabled rk_gmac-dwmac fe2a0000.ethernet: Using 32/32 bits DMA host/devich mdio_bus stmmac-0: MDIO device at address 0 is missing.rk_gmac-dwmac fe010000.ethernet eth0: Register
MEM_TYPE_PAGE_POO0rk_gmac-dwmac fe010000.ethernet eth0:__stmmac_open: Cannot atta)Second, running 'lspci' and 'lsusb' doesn't see any devices on PCIe and USB. I guess the device tree might be updated. Anyone has idea how to fix it? Thanks.
Quoted 7 lines
- Doug
_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip
I've seen similar errors on other boards when the phy is not powered or does not have a clock supplied. Could you check your DT if there is any diffs in the phy-supply or any gpio-Hog pulling the enable of a regulator that might enable the phy? Also you could check if you have all the required regulator drivers available and probed.
Best regards
Johannes
Signature · 10 lines
Pengutronix e.K. | Johannes Zink | Steuerwalder Str. 21 | https://www.pengutronix.de/ | 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686| Fax: +49-5121-206917-5555 | _______________________________________________ Linux-rockchip mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-rockchip
Hi
Quoted 66 lines
Gesendet: Donnerstag, 13. April 2023 um 08:28 Uhr
Von: "Johannes Zink" <[email protected]>
An: [email protected]
Betreff: Re: Problems about NIC, PCIe and usb on RK3568 EVBHi Doug,
Quoted 49 lines · Doug Brewer
Hi,
I tested Linux kernel 6.3-rc6 on my rk3568 evaluation board, it seems there are problems with Ethernet, PCIe and usb devices.
First, NICs doesn't work.
rk_gmac-dwmac fe010000.ethernet: IRQ eth_lpi not found rk_gmac-dwmac fe010000.ethernet: no regulator found rk_gmac-dwmac fe010000.ethernet: clock input or output? (output). rk_gmac-dwmac fe010000.ethernet: Can not read property: tx_delay. rk_gmac-dwmac fe010000.ethernet: set tx_delay to 0x30 rk_gmac-dwmac fe010000.ethernet: Can not read property: rx_delay. rk_gmac-dwmac fe010000.ethernet: set rx_delay to 0x10 rk_gmac-dwmac fe010000.ethernet: integrated PHY? (no). rk_gmac-dwmac fe010000.ethernet: init for RGMII_ID rk_gmac-dwmac fe010000.ethernet: User ID: 0x30, Synopsys ID: 0x51 rk_gmac-dwmac fe010000.ethernet: DWMAC4/5 rk_gmac-dwmac fe010000.ethernet: DMA HW capability register suppd rk_gmac-dwmac fe010000.ethernet: RX Checksum Offload Engine suppd rk_gmac-dwmac fe010000.ethernet: TX Checksum insertion supported rk_gmac-dwmac fe010000.ethernet: Wake-Up On Lan supported rk_gmac-dwmac fe010000.ethernet: TSO supported rk_gmac-dwmac fe010000.ethernet: Enable RX Mitigation via HW Watr rk_gmac-dwmac fe010000.ethernet: Enabled RFS Flow TC (entries=10) rk_gmac-dwmac fe010000.ethernet: TSO feature enabled rk_gmac-dwmac fe010000.ethernet: Using 32/32 bits DMA host/devich mdio_bus stmmac-1: MDIO device at address 0 is missing. rk_gmac-dwmac fe2a0000.ethernet: IRQ eth_lpi not found rk_gmac-dwmac fe2a0000.ethernet: no regulator found rk_gmac-dwmac fe2a0000.ethernet: clock input or output? (output). rk_gmac-dwmac fe2a0000.ethernet: Can not read property: tx_delay. rk_gmac-dwmac fe2a0000.ethernet: set tx_delay to 0x30 rk_gmac-dwmac fe2a0000.ethernet: Can not read property: rx_delay. rk_gmac-dwmac fe2a0000.ethernet: set rx_delay to 0x10 rk_gmac-dwmac fe2a0000.ethernet: integrated PHY? (no). rk_gmac-dwmac fe2a0000.ethernet: init for RGMII_ID rk_gmac-dwmac fe2a0000.ethernet: User ID: 0x30, Synopsys ID: 0x51 rk_gmac-dwmac fe2a0000.ethernet: DWMAC4/5 rk_gmac-dwmac fe2a0000.ethernet: DMA HW capability register suppd rk_gmac-dwmac fe2a0000.ethernet: RX Checksum Offload Engine suppd rk_gmac-dwmac fe2a0000.ethernet: TX Checksum insertion supported rk_gmac-dwmac fe2a0000.ethernet: Wake-Up On Lan supported rk_gmac-dwmac fe2a0000.ethernet: TSO supported rk_gmac-dwmac fe2a0000.ethernet: Enable RX Mitigation via HW Watr rk_gmac-dwmac fe2a0000.ethernet: Enabled RFS Flow TC (entries=10) rk_gmac-dwmac fe2a0000.ethernet: TSO feature enabled rk_gmac-dwmac fe2a0000.ethernet: Using 32/32 bits DMA host/devich mdio_bus stmmac-0: MDIO device at address 0 is missing.Quoted 8 lines
rk_gmac-dwmac fe010000.ethernet eth0: Register
MEM_TYPE_PAGE_POO0rk_gmac-dwmac fe010000.ethernet eth0:__stmmac_open: Cannot atta)Second, running 'lspci' and 'lsusb' doesn't see any devices on PCIe and USB. I guess the device tree might be updated. Anyone has idea how to fix it? Thanks.
- Doug
Quoted 8 lines
I've seen similar errors on other boards when the phy is not powered or does not have a clock supplied. Could you check your DT if there is any diffs in the phy-supply or any gpio-Hog pulling the enable of a regulator that might enable the phy? Also you could check if you have all the required regulator drivers available and probed.
Best regards
Johannes
i tested 6.3.0-rc4 on my banaanpi r2pro and there it seem no problem...do you have the issue on rc4 too?
root@bpi-r2pro:~# dmesg | grep rk_gmac-dwmac
[ 3.033681] rk_gmac-dwmac fe010000.ethernet: IRQ eth_lpi not found
[ 3.034528] rk_gmac-dwmac fe010000.ethernet: Looking up phy-supply from devie
[ 3.035243] rk_gmac-dwmac fe010000.ethernet: Looking up phy-supply property d
[ 3.036170] rk_gmac-dwmac fe010000.ethernet: no regulator found
[ 3.036713] rk_gmac-dwmac fe010000.ethernet: clock input or output? (output).
[ 3.037361] rk_gmac-dwmac fe010000.ethernet: TX delay(0x3c).
[ 3.037877] rk_gmac-dwmac fe010000.ethernet: RX delay(0x2f).
[ 3.038398] rk_gmac-dwmac fe010000.ethernet: integrated PHY? (no).
[ 3.044063] rk_gmac-dwmac fe010000.ethernet: init for RGMII
[ 3.044896] rk_gmac-dwmac fe010000.ethernet: User ID: 0x30, Synopsys ID: 0x51
[ 3.045559] rk_gmac-dwmac fe010000.ethernet: DWMAC4/5
[ 3.046033] rk_gmac-dwmac fe010000.ethernet: DMA HW capability register suppd
[ 3.046747] rk_gmac-dwmac fe010000.ethernet: RX Checksum Offload Engine suppd
[ 3.047428] rk_gmac-dwmac fe010000.ethernet: TX Checksum insertion supported
[ 3.048062] rk_gmac-dwmac fe010000.ethernet: Wake-Up On Lan supported
[ 3.048725] rk_gmac-dwmac fe010000.ethernet: TSO supported
[ 3.049229] rk_gmac-dwmac fe010000.ethernet: Enable RX Mitigation via HW Watr
[ 3.049954] rk_gmac-dwmac fe010000.ethernet: Enabled RFS Flow TC (entries=10)
[ 3.050628] rk_gmac-dwmac fe010000.ethernet: TSO feature enabled
[ 3.051176] rk_gmac-dwmac fe010000.ethernet: Using 32/32 bits DMA host/devich
[ 3.189988] rk_gmac-dwmac fe2a0000.ethernet: IRQ eth_lpi not found
[ 3.190982] rk_gmac-dwmac fe2a0000.ethernet: Looking up phy-supply from devie
[ 3.191715] rk_gmac-dwmac fe2a0000.ethernet: Looking up phy-supply property d
[ 3.192636] rk_gmac-dwmac fe2a0000.ethernet: no regulator found
[ 3.193180] rk_gmac-dwmac fe2a0000.ethernet: clock input or output? (input).
[ 3.193818] rk_gmac-dwmac fe2a0000.ethernet: TX delay(0x4f).
[ 3.194336] rk_gmac-dwmac fe2a0000.ethernet: RX delay(0xf).
[ 3.194885] rk_gmac-dwmac fe2a0000.ethernet: integrated PHY? (no).
[ 3.195499] rk_gmac-dwmac fe2a0000.ethernet: clock input from PHY
[ 3.201067] rk_gmac-dwmac fe2a0000.ethernet: init for RGMII
[ 3.201885] rk_gmac-dwmac fe2a0000.ethernet: User ID: 0x30, Synopsys ID: 0x51
[ 3.202575] rk_gmac-dwmac fe2a0000.ethernet: DWMAC4/5
[ 3.203052] rk_gmac-dwmac fe2a0000.ethernet: DMA HW capability register suppd
[ 3.203730] rk_gmac-dwmac fe2a0000.ethernet: RX Checksum Offload Engine suppd
[ 3.204405] rk_gmac-dwmac fe2a0000.ethernet: TX Checksum insertion supported
[ 3.205039] rk_gmac-dwmac fe2a0000.ethernet: Wake-Up On Lan supported
[ 3.205702] rk_gmac-dwmac fe2a0000.ethernet: TSO supported
[ 3.206207] rk_gmac-dwmac fe2a0000.ethernet: Enable RX Mitigation via HW Watr
[ 3.206969] rk_gmac-dwmac fe2a0000.ethernet: Enabled RFS Flow TC (entries=10)
[ 3.207621] rk_gmac-dwmac fe2a0000.ethernet: TSO feature enabled
[ 3.208167] rk_gmac-dwmac fe2a0000.ethernet: Using 32/32 bits DMA host/devich
[ 80.517694] rk_gmac-dwmac fe010000.ethernet eth0: Register MEM_TYPE_PAGE_POO0
[ 80.520178] rk_gmac-dwmac fe010000.ethernet eth0: PHY [stmmac-1:00] driver [)
[ 80.520230] rk_gmac-dwmac fe010000.ethernet eth0: No Safety Features supportd
[ 80.520258] rk_gmac-dwmac fe010000.ethernet eth0: IEEE 1588-2008 Advanced Tid
[ 80.520514] rk_gmac-dwmac fe010000.ethernet eth0: registered PTP clock
[ 80.520898] rk_gmac-dwmac fe010000.ethernet eth0: configuring for phy/rgmii e
[ 84.615184] rk_gmac-dwmac fe010000.ethernet eth0: Link is Up - 1Gbps/Full - x
root@bpi-r2pro:~# ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group defau0
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group def0
link/ether 76:95:00:96:b3:89 brd ff:ff:ff:ff:ff:ff
inet 192.168.0.12/24 scope global eth0
valid_lft forever preferred_lft forever
inet6 fe80::7495:ff:fe96:b389/64 scope link
valid_lft forever preferred_lft forever
3: eth1: <BROADCAST,MULTICAST> mtu 1504 qdisc noop state DOWN group default qle0
link/ether 76:95:00:96:b3:88 brd ff:ff:ff:ff:ff:ff
4: sit0@NONE: <NOARP> mtu 1480 qdisc noop state DOWN group default qlen 1000
link/sit 0.0.0.0 brd 0.0.0.0
5: lan0@eth1: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc noop state DOWN group0
link/ether 76:95:00:96:b3:88 brd ff:ff:ff:ff:ff:ff
6: lan1@eth1: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc noop state DOWN group0
link/ether 76:95:00:96:b3:88 brd ff:ff:ff:ff:ff:ff
7: lan2@eth1: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc noop state DOWN group0
link/ether 76:95:00:96:b3:88 brd ff:ff:ff:ff:ff:ff
8: lan3@eth1: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc noop state DOWN group0
link/ether 76:95:00:96:b3:88 brd ff:ff:ff:ff:ff:ff
root@bpi-r2pro:~# lsusb
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 008 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 007 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
root@bpi-r2pro:~# lspci
0001:00:00.0 PCI bridge: Rockchip Electronics Co., Ltd RK3568 Remote Signal Pro)
0002:00:00.0 PCI bridge: Rockchip Electronics Co., Ltd RK3568 Remote Signal Pro)
root@bpi-r2pro:~# uname -a
Linux bpi-r2pro 6.3.0-rc4-bpi-r2pro #1 SMP PREEMPT Mon Apr 10 13:39:18 CEST 202x
root@bpi-r2pro:~#tested eth1 too...also working. so maybe "only" a evb related dts-change or between rc4 and rc6
regards Frank
_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip
Quoted 74 lines · Frank Wunderlich
Hi
Quoted 72 lines
Gesendet: Donnerstag, 13. April 2023 um 08:28 Uhr
Von: "Johannes Zink" <[email protected]>
An: [email protected]
Betreff: Re: Problems about NIC, PCIe and usb on RK3568 EVBHi Doug,
Quoted 49 lines · Doug Brewer
Hi,
I tested Linux kernel 6.3-rc6 on my rk3568 evaluation board, it seems there are problems with Ethernet, PCIe and usb devices.
First, NICs doesn't work.
rk_gmac-dwmac fe010000.ethernet: IRQ eth_lpi not found rk_gmac-dwmac fe010000.ethernet: no regulator found rk_gmac-dwmac fe010000.ethernet: clock input or output? (output). rk_gmac-dwmac fe010000.ethernet: Can not read property: tx_delay. rk_gmac-dwmac fe010000.ethernet: set tx_delay to 0x30 rk_gmac-dwmac fe010000.ethernet: Can not read property: rx_delay. rk_gmac-dwmac fe010000.ethernet: set rx_delay to 0x10 rk_gmac-dwmac fe010000.ethernet: integrated PHY? (no). rk_gmac-dwmac fe010000.ethernet: init for RGMII_ID rk_gmac-dwmac fe010000.ethernet: User ID: 0x30, Synopsys ID: 0x51 rk_gmac-dwmac fe010000.ethernet: DWMAC4/5 rk_gmac-dwmac fe010000.ethernet: DMA HW capability register suppd rk_gmac-dwmac fe010000.ethernet: RX Checksum Offload Engine suppd rk_gmac-dwmac fe010000.ethernet: TX Checksum insertion supported rk_gmac-dwmac fe010000.ethernet: Wake-Up On Lan supported rk_gmac-dwmac fe010000.ethernet: TSO supported rk_gmac-dwmac fe010000.ethernet: Enable RX Mitigation via HW Watr rk_gmac-dwmac fe010000.ethernet: Enabled RFS Flow TC (entries=10) rk_gmac-dwmac fe010000.ethernet: TSO feature enabled rk_gmac-dwmac fe010000.ethernet: Using 32/32 bits DMA host/devich mdio_bus stmmac-1: MDIO device at address 0 is missing. rk_gmac-dwmac fe2a0000.ethernet: IRQ eth_lpi not found rk_gmac-dwmac fe2a0000.ethernet: no regulator found rk_gmac-dwmac fe2a0000.ethernet: clock input or output? (output). rk_gmac-dwmac fe2a0000.ethernet: Can not read property: tx_delay. rk_gmac-dwmac fe2a0000.ethernet: set tx_delay to 0x30 rk_gmac-dwmac fe2a0000.ethernet: Can not read property: rx_delay. rk_gmac-dwmac fe2a0000.ethernet: set rx_delay to 0x10 rk_gmac-dwmac fe2a0000.ethernet: integrated PHY? (no). rk_gmac-dwmac fe2a0000.ethernet: init for RGMII_ID rk_gmac-dwmac fe2a0000.ethernet: User ID: 0x30, Synopsys ID: 0x51 rk_gmac-dwmac fe2a0000.ethernet: DWMAC4/5 rk_gmac-dwmac fe2a0000.ethernet: DMA HW capability register suppd rk_gmac-dwmac fe2a0000.ethernet: RX Checksum Offload Engine suppd rk_gmac-dwmac fe2a0000.ethernet: TX Checksum insertion supported rk_gmac-dwmac fe2a0000.ethernet: Wake-Up On Lan supported rk_gmac-dwmac fe2a0000.ethernet: TSO supported rk_gmac-dwmac fe2a0000.ethernet: Enable RX Mitigation via HW Watr rk_gmac-dwmac fe2a0000.ethernet: Enabled RFS Flow TC (entries=10) rk_gmac-dwmac fe2a0000.ethernet: TSO feature enabled rk_gmac-dwmac fe2a0000.ethernet: Using 32/32 bits DMA host/devich mdio_bus stmmac-0: MDIO device at address 0 is missing.Quoted 8 lines
rk_gmac-dwmac fe010000.ethernet eth0: Register
MEM_TYPE_PAGE_POO0rk_gmac-dwmac fe010000.ethernet eth0:__stmmac_open: Cannot atta)Second, running 'lspci' and 'lsusb' doesn't see any devices on PCIe and USB. I guess the device tree might be updated. Anyone has idea how to fix it? Thanks.
- Doug
I've seen similar errors on other boards when the phy is not powered or does not have a clock supplied. Could you check your DT if there is any diffs in the phy-supply or any gpio-Hog pulling the enable of a regulator that might enable the phy? Also you could check if you have all the required regulator drivers available and probed.
Quoted 4 lines
Quoted 2 lines
Best regards
Johannesi tested 6.3.0-rc4 on my banaanpi r2pro and there it seem no problem...do you have the issue on rc4 too?
I just tested 6.3.0-rc4 on my rk3568 evb, no luck.
# dmesg |grep rk_gmac [ 11.381071] rk_gmac-dwmac fe010000.ethernet: IRQ eth_lpi not found [ 11.381892] rk_gmac-dwmac fe010000.ethernet: no regulator found [ 11.382529] rk_gmac-dwmac fe010000.ethernet: clock input or output? (output). [ 11.383178] rk_gmac-dwmac fe010000.ethernet: Can not read property: tx_delay. [ 11.383815] rk_gmac-dwmac fe010000.ethernet: set tx_delay to 0x30 [ 11.384373] rk_gmac-dwmac fe010000.ethernet: Can not read property: rx_delay. [ 11.385008] rk_gmac-dwmac fe010000.ethernet: set rx_delay to 0x10 [ 11.385561] rk_gmac-dwmac fe010000.ethernet: integrated PHY? (no). [ 11.396162] rk_gmac-dwmac fe010000.ethernet: init for RGMII_ID [ 11.400201] rk_gmac-dwmac fe010000.ethernet: User ID: 0x30, Synopsys ID: 0x51 [ 11.400878] rk_gmac-dwmac fe010000.ethernet: DWMAC4/5 [ 11.401349] rk_gmac-dwmac fe010000.ethernet: DMA HW capability register suppd [ 11.402067] rk_gmac-dwmac fe010000.ethernet: RX Checksum Offload Engine suppd [ 11.402755] rk_gmac-dwmac fe010000.ethernet: TX Checksum insertion supported [ 11.403401] rk_gmac-dwmac fe010000.ethernet: Wake-Up On Lan supported [ 11.404185] rk_gmac-dwmac fe010000.ethernet: TSO supported [ 11.406883] rk_gmac-dwmac fe010000.ethernet: Enable RX Mitigation via HW Watr [ 11.407964] rk_gmac-dwmac fe010000.ethernet: Enabled RFS Flow TC (entries=10) [ 11.408624] rk_gmac-dwmac fe010000.ethernet: TSO feature enabled [ 11.411098] rk_gmac-dwmac fe010000.ethernet: Using 32/32 bits DMA host/devich [ 11.421076] rk_gmac-dwmac fe2a0000.ethernet: IRQ eth_lpi not found [ 11.422308] rk_gmac-dwmac fe2a0000.ethernet: no regulator found [ 11.422870] rk_gmac-dwmac fe2a0000.ethernet: clock input or output? (output). [ 11.423515] rk_gmac-dwmac fe2a0000.ethernet: Can not read property: tx_delay. [ 11.425161] rk_gmac-dwmac fe2a0000.ethernet: set tx_delay to 0x30 [ 11.425862] rk_gmac-dwmac fe2a0000.ethernet: Can not read property: rx_delay. [ 11.426731] rk_gmac-dwmac fe2a0000.ethernet: set rx_delay to 0x10 [ 11.427430] rk_gmac-dwmac fe2a0000.ethernet: integrated PHY? (no). [ 11.433094] rk_gmac-dwmac fe2a0000.ethernet: init for RGMII_ID [ 11.445612] rk_gmac-dwmac fe2a0000.ethernet: User ID: 0x30, Synopsys ID: 0x51 [ 11.446753] rk_gmac-dwmac fe2a0000.ethernet: DWMAC4/5 [ 11.447265] rk_gmac-dwmac fe2a0000.ethernet: DMA HW capability register suppd [ 11.447940] rk_gmac-dwmac fe2a0000.ethernet: RX Checksum Offload Engine suppd [ 11.448612] rk_gmac-dwmac fe2a0000.ethernet: TX Checksum insertion supported [ 11.449536] rk_gmac-dwmac fe2a0000.ethernet: Wake-Up On Lan supported [ 11.452947] rk_gmac-dwmac fe2a0000.ethernet: TSO supported [ 11.453468] rk_gmac-dwmac fe2a0000.ethernet: Enable RX Mitigation via HW Watr [ 11.454401] rk_gmac-dwmac fe2a0000.ethernet: Enabled RFS Flow TC (entries=10) [ 11.455054] rk_gmac-dwmac fe2a0000.ethernet: TSO feature enabled [ 11.456887] rk_gmac-dwmac fe2a0000.ethernet: Using 32/32 bits DMA host/devich [ 12.340615] rk_gmac-dwmac fe010000.ethernet eth0: Register MEM_TYPE_PAGE_POO0 [ 12.342575] rk_gmac-dwmac fe010000.ethernet eth0: no phy found [ 12.343121] rk_gmac-dwmac fe010000.ethernet eth0: __stmmac_open: Cannot atta)
Quoted 91 lines
root@bpi-r2pro:~# dmesg | grep rk_gmac-dwmac
[ 3.033681] rk_gmac-dwmac fe010000.ethernet: IRQ eth_lpi not found
[ 3.034528] rk_gmac-dwmac fe010000.ethernet: Looking up phy-supply from devie
[ 3.035243] rk_gmac-dwmac fe010000.ethernet: Looking up phy-supply property d
[ 3.036170] rk_gmac-dwmac fe010000.ethernet: no regulator found
[ 3.036713] rk_gmac-dwmac fe010000.ethernet: clock input or output? (output).
[ 3.037361] rk_gmac-dwmac fe010000.ethernet: TX delay(0x3c).
[ 3.037877] rk_gmac-dwmac fe010000.ethernet: RX delay(0x2f).
[ 3.038398] rk_gmac-dwmac fe010000.ethernet: integrated PHY? (no).
[ 3.044063] rk_gmac-dwmac fe010000.ethernet: init for RGMII
[ 3.044896] rk_gmac-dwmac fe010000.ethernet: User ID: 0x30, Synopsys ID: 0x51
[ 3.045559] rk_gmac-dwmac fe010000.ethernet: DWMAC4/5
[ 3.046033] rk_gmac-dwmac fe010000.ethernet: DMA HW capability register suppd
[ 3.046747] rk_gmac-dwmac fe010000.ethernet: RX Checksum Offload Engine suppd
[ 3.047428] rk_gmac-dwmac fe010000.ethernet: TX Checksum insertion supported
[ 3.048062] rk_gmac-dwmac fe010000.ethernet: Wake-Up On Lan supported
[ 3.048725] rk_gmac-dwmac fe010000.ethernet: TSO supported
[ 3.049229] rk_gmac-dwmac fe010000.ethernet: Enable RX Mitigation via HW Watr
[ 3.049954] rk_gmac-dwmac fe010000.ethernet: Enabled RFS Flow TC (entries=10)
[ 3.050628] rk_gmac-dwmac fe010000.ethernet: TSO feature enabled
[ 3.051176] rk_gmac-dwmac fe010000.ethernet: Using 32/32 bits DMA host/devich
[ 3.189988] rk_gmac-dwmac fe2a0000.ethernet: IRQ eth_lpi not found
[ 3.190982] rk_gmac-dwmac fe2a0000.ethernet: Looking up phy-supply from devie
[ 3.191715] rk_gmac-dwmac fe2a0000.ethernet: Looking up phy-supply property d
[ 3.192636] rk_gmac-dwmac fe2a0000.ethernet: no regulator found
[ 3.193180] rk_gmac-dwmac fe2a0000.ethernet: clock input or output? (input).
[ 3.193818] rk_gmac-dwmac fe2a0000.ethernet: TX delay(0x4f).
[ 3.194336] rk_gmac-dwmac fe2a0000.ethernet: RX delay(0xf).
[ 3.194885] rk_gmac-dwmac fe2a0000.ethernet: integrated PHY? (no).
[ 3.195499] rk_gmac-dwmac fe2a0000.ethernet: clock input from PHY
[ 3.201067] rk_gmac-dwmac fe2a0000.ethernet: init for RGMII
[ 3.201885] rk_gmac-dwmac fe2a0000.ethernet: User ID: 0x30, Synopsys ID: 0x51
[ 3.202575] rk_gmac-dwmac fe2a0000.ethernet: DWMAC4/5
[ 3.203052] rk_gmac-dwmac fe2a0000.ethernet: DMA HW capability register suppd
[ 3.203730] rk_gmac-dwmac fe2a0000.ethernet: RX Checksum Offload Engine suppd
[ 3.204405] rk_gmac-dwmac fe2a0000.ethernet: TX Checksum insertion supported
[ 3.205039] rk_gmac-dwmac fe2a0000.ethernet: Wake-Up On Lan supported
[ 3.205702] rk_gmac-dwmac fe2a0000.ethernet: TSO supported
[ 3.206207] rk_gmac-dwmac fe2a0000.ethernet: Enable RX Mitigation via HW Watr
[ 3.206969] rk_gmac-dwmac fe2a0000.ethernet: Enabled RFS Flow TC (entries=10)
[ 3.207621] rk_gmac-dwmac fe2a0000.ethernet: TSO feature enabled
[ 3.208167] rk_gmac-dwmac fe2a0000.ethernet: Using 32/32 bits DMA host/devich
[ 80.517694] rk_gmac-dwmac fe010000.ethernet eth0: Register MEM_TYPE_PAGE_POO0
[ 80.520178] rk_gmac-dwmac fe010000.ethernet eth0: PHY [stmmac-1:00] driver [)
[ 80.520230] rk_gmac-dwmac fe010000.ethernet eth0: No Safety Features supportd
[ 80.520258] rk_gmac-dwmac fe010000.ethernet eth0: IEEE 1588-2008 Advanced Tid
[ 80.520514] rk_gmac-dwmac fe010000.ethernet eth0: registered PTP clock
[ 80.520898] rk_gmac-dwmac fe010000.ethernet eth0: configuring for phy/rgmii e
[ 84.615184] rk_gmac-dwmac fe010000.ethernet eth0: Link is Up - 1Gbps/Full - x
root@bpi-r2pro:~# ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group defau0
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group def0
link/ether 76:95:00:96:b3:89 brd ff:ff:ff:ff:ff:ff
inet 192.168.0.12/24 scope global eth0
valid_lft forever preferred_lft forever
inet6 fe80::7495:ff:fe96:b389/64 scope link
valid_lft forever preferred_lft forever
3: eth1: <BROADCAST,MULTICAST> mtu 1504 qdisc noop state DOWN group default qle0
link/ether 76:95:00:96:b3:88 brd ff:ff:ff:ff:ff:ff
4: sit0@NONE: <NOARP> mtu 1480 qdisc noop state DOWN group default qlen 1000
link/sit 0.0.0.0 brd 0.0.0.0
5: lan0@eth1: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc noop state DOWN group0
link/ether 76:95:00:96:b3:88 brd ff:ff:ff:ff:ff:ff
6: lan1@eth1: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc noop state DOWN group0
link/ether 76:95:00:96:b3:88 brd ff:ff:ff:ff:ff:ff
7: lan2@eth1: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc noop state DOWN group0
link/ether 76:95:00:96:b3:88 brd ff:ff:ff:ff:ff:ff
8: lan3@eth1: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc noop state DOWN group0
link/ether 76:95:00:96:b3:88 brd ff:ff:ff:ff:ff:ff
root@bpi-r2pro:~# lsusb
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 008 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 007 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
root@bpi-r2pro:~# lspci
0001:00:00.0 PCI bridge: Rockchip Electronics Co., Ltd RK3568 Remote Signal Pro)
0002:00:00.0 PCI bridge: Rockchip Electronics Co., Ltd RK3568 Remote Signal Pro)
root@bpi-r2pro:~# uname -a
Linux bpi-r2pro 6.3.0-rc4-bpi-r2pro #1 SMP PREEMPT Mon Apr 10 13:39:18 CEST 202x
root@bpi-r2pro:~#Quoted 1 line
tested eth1 too...also working. so maybe "only" a evb related dts-change or between rc4 and rc6
Maybe the device tree is not correct on evb...
Quoted 2 lines
regards Frank
- Doug
_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip
Quoted 75 lines
Gesendet: Donnerstag, 13. April 2023 um 11:21 Uhr
Von: "Doug Brewer" <[email protected]>Quoted 69 lines · Frank Wunderlich
Hi
Quoted 67 lines
Gesendet: Donnerstag, 13. April 2023 um 08:28 Uhr
Von: "Johannes Zink" <[email protected]>Quoted 49 lines · Doug Brewer
Hi,
I tested Linux kernel 6.3-rc6 on my rk3568 evaluation board, it seems there are problems with Ethernet, PCIe and usb devices.
First, NICs doesn't work.
rk_gmac-dwmac fe010000.ethernet: IRQ eth_lpi not found rk_gmac-dwmac fe010000.ethernet: no regulator found rk_gmac-dwmac fe010000.ethernet: clock input or output? (output). rk_gmac-dwmac fe010000.ethernet: Can not read property: tx_delay. rk_gmac-dwmac fe010000.ethernet: set tx_delay to 0x30 rk_gmac-dwmac fe010000.ethernet: Can not read property: rx_delay. rk_gmac-dwmac fe010000.ethernet: set rx_delay to 0x10 rk_gmac-dwmac fe010000.ethernet: integrated PHY? (no). rk_gmac-dwmac fe010000.ethernet: init for RGMII_ID rk_gmac-dwmac fe010000.ethernet: User ID: 0x30, Synopsys ID: 0x51 rk_gmac-dwmac fe010000.ethernet: DWMAC4/5 rk_gmac-dwmac fe010000.ethernet: DMA HW capability register suppd rk_gmac-dwmac fe010000.ethernet: RX Checksum Offload Engine suppd rk_gmac-dwmac fe010000.ethernet: TX Checksum insertion supported rk_gmac-dwmac fe010000.ethernet: Wake-Up On Lan supported rk_gmac-dwmac fe010000.ethernet: TSO supported rk_gmac-dwmac fe010000.ethernet: Enable RX Mitigation via HW Watr rk_gmac-dwmac fe010000.ethernet: Enabled RFS Flow TC (entries=10) rk_gmac-dwmac fe010000.ethernet: TSO feature enabled rk_gmac-dwmac fe010000.ethernet: Using 32/32 bits DMA host/devich mdio_bus stmmac-1: MDIO device at address 0 is missing. rk_gmac-dwmac fe2a0000.ethernet: IRQ eth_lpi not found rk_gmac-dwmac fe2a0000.ethernet: no regulator found rk_gmac-dwmac fe2a0000.ethernet: clock input or output? (output). rk_gmac-dwmac fe2a0000.ethernet: Can not read property: tx_delay. rk_gmac-dwmac fe2a0000.ethernet: set tx_delay to 0x30 rk_gmac-dwmac fe2a0000.ethernet: Can not read property: rx_delay. rk_gmac-dwmac fe2a0000.ethernet: set rx_delay to 0x10 rk_gmac-dwmac fe2a0000.ethernet: integrated PHY? (no). rk_gmac-dwmac fe2a0000.ethernet: init for RGMII_ID rk_gmac-dwmac fe2a0000.ethernet: User ID: 0x30, Synopsys ID: 0x51 rk_gmac-dwmac fe2a0000.ethernet: DWMAC4/5 rk_gmac-dwmac fe2a0000.ethernet: DMA HW capability register suppd rk_gmac-dwmac fe2a0000.ethernet: RX Checksum Offload Engine suppd rk_gmac-dwmac fe2a0000.ethernet: TX Checksum insertion supported rk_gmac-dwmac fe2a0000.ethernet: Wake-Up On Lan supported rk_gmac-dwmac fe2a0000.ethernet: TSO supported rk_gmac-dwmac fe2a0000.ethernet: Enable RX Mitigation via HW Watr rk_gmac-dwmac fe2a0000.ethernet: Enabled RFS Flow TC (entries=10) rk_gmac-dwmac fe2a0000.ethernet: TSO feature enabled rk_gmac-dwmac fe2a0000.ethernet: Using 32/32 bits DMA host/devich mdio_bus stmmac-0: MDIO device at address 0 is missing.Quoted 8 lines
rk_gmac-dwmac fe010000.ethernet eth0: Register
MEM_TYPE_PAGE_POO0rk_gmac-dwmac fe010000.ethernet eth0:__stmmac_open: Cannot atta)Second, running 'lspci' and 'lsusb' doesn't see any devices on PCIe and USB. I guess the device tree might be updated. Anyone has idea how to fix it? Thanks.
- Doug
I've seen similar errors on other boards when the phy is not powered or does not have a clock supplied. Could you check your DT if there is any diffs in the phy-supply or any gpio-Hog pulling the enable of a regulator that might enable the phy? Also you could check if you have all the required regulator drivers available and probed.
Quoted 6 lines
Quoted 4 lines
Quoted 2 lines
Best regards
Johannesi tested 6.3.0-rc4 on my banaanpi r2pro and there it seem no problem...do you have the issue on rc4 too?
I just tested 6.3.0-rc4 on my rk3568 evb, no luck.
was 6.2.0 working?
you should upload your full dmesg and .config to pastebin or similar and send the linke here
Quoted 138 lines
# dmesg |grep rk_gmac [ 11.381071] rk_gmac-dwmac fe010000.ethernet: IRQ eth_lpi not found [ 11.381892] rk_gmac-dwmac fe010000.ethernet: no regulator found [ 11.382529] rk_gmac-dwmac fe010000.ethernet: clock input or output? (output). [ 11.383178] rk_gmac-dwmac fe010000.ethernet: Can not read property: tx_delay. [ 11.383815] rk_gmac-dwmac fe010000.ethernet: set tx_delay to 0x30 [ 11.384373] rk_gmac-dwmac fe010000.ethernet: Can not read property: rx_delay. [ 11.385008] rk_gmac-dwmac fe010000.ethernet: set rx_delay to 0x10 [ 11.385561] rk_gmac-dwmac fe010000.ethernet: integrated PHY? (no). [ 11.396162] rk_gmac-dwmac fe010000.ethernet: init for RGMII_ID [ 11.400201] rk_gmac-dwmac fe010000.ethernet: User ID: 0x30, Synopsys ID: 0x51 [ 11.400878] rk_gmac-dwmac fe010000.ethernet: DWMAC4/5 [ 11.401349] rk_gmac-dwmac fe010000.ethernet: DMA HW capability register suppd [ 11.402067] rk_gmac-dwmac fe010000.ethernet: RX Checksum Offload Engine suppd [ 11.402755] rk_gmac-dwmac fe010000.ethernet: TX Checksum insertion supported [ 11.403401] rk_gmac-dwmac fe010000.ethernet: Wake-Up On Lan supported [ 11.404185] rk_gmac-dwmac fe010000.ethernet: TSO supported [ 11.406883] rk_gmac-dwmac fe010000.ethernet: Enable RX Mitigation via HW Watr [ 11.407964] rk_gmac-dwmac fe010000.ethernet: Enabled RFS Flow TC (entries=10) [ 11.408624] rk_gmac-dwmac fe010000.ethernet: TSO feature enabled [ 11.411098] rk_gmac-dwmac fe010000.ethernet: Using 32/32 bits DMA host/devich [ 11.421076] rk_gmac-dwmac fe2a0000.ethernet: IRQ eth_lpi not found [ 11.422308] rk_gmac-dwmac fe2a0000.ethernet: no regulator found [ 11.422870] rk_gmac-dwmac fe2a0000.ethernet: clock input or output? (output). [ 11.423515] rk_gmac-dwmac fe2a0000.ethernet: Can not read property: tx_delay. [ 11.425161] rk_gmac-dwmac fe2a0000.ethernet: set tx_delay to 0x30 [ 11.425862] rk_gmac-dwmac fe2a0000.ethernet: Can not read property: rx_delay. [ 11.426731] rk_gmac-dwmac fe2a0000.ethernet: set rx_delay to 0x10 [ 11.427430] rk_gmac-dwmac fe2a0000.ethernet: integrated PHY? (no). [ 11.433094] rk_gmac-dwmac fe2a0000.ethernet: init for RGMII_ID [ 11.445612] rk_gmac-dwmac fe2a0000.ethernet: User ID: 0x30, Synopsys ID: 0x51 [ 11.446753] rk_gmac-dwmac fe2a0000.ethernet: DWMAC4/5 [ 11.447265] rk_gmac-dwmac fe2a0000.ethernet: DMA HW capability register suppd [ 11.447940] rk_gmac-dwmac fe2a0000.ethernet: RX Checksum Offload Engine suppd [ 11.448612] rk_gmac-dwmac fe2a0000.ethernet: TX Checksum insertion supported [ 11.449536] rk_gmac-dwmac fe2a0000.ethernet: Wake-Up On Lan supported [ 11.452947] rk_gmac-dwmac fe2a0000.ethernet: TSO supported [ 11.453468] rk_gmac-dwmac fe2a0000.ethernet: Enable RX Mitigation via HW Watr [ 11.454401] rk_gmac-dwmac fe2a0000.ethernet: Enabled RFS Flow TC (entries=10) [ 11.455054] rk_gmac-dwmac fe2a0000.ethernet: TSO feature enabled [ 11.456887] rk_gmac-dwmac fe2a0000.ethernet: Using 32/32 bits DMA host/devich [ 12.340615] rk_gmac-dwmac fe010000.ethernet eth0: Register MEM_TYPE_PAGE_POO0 [ 12.342575] rk_gmac-dwmac fe010000.ethernet eth0: no phy found [ 12.343121] rk_gmac-dwmac fe010000.ethernet eth0: __stmmac_open: Cannot atta)Quoted 91 lines
root@bpi-r2pro:~# dmesg | grep rk_gmac-dwmac [ 3.033681] rk_gmac-dwmac fe010000.ethernet: IRQ eth_lpi not found [ 3.034528] rk_gmac-dwmac fe010000.ethernet: Looking up phy-supply from devie [ 3.035243] rk_gmac-dwmac fe010000.ethernet: Looking up phy-supply property d [ 3.036170] rk_gmac-dwmac fe010000.ethernet: no regulator found [ 3.036713] rk_gmac-dwmac fe010000.ethernet: clock input or output? (output). [ 3.037361] rk_gmac-dwmac fe010000.ethernet: TX delay(0x3c). [ 3.037877] rk_gmac-dwmac fe010000.ethernet: RX delay(0x2f). [ 3.038398] rk_gmac-dwmac fe010000.ethernet: integrated PHY? (no). [ 3.044063] rk_gmac-dwmac fe010000.ethernet: init for RGMII [ 3.044896] rk_gmac-dwmac fe010000.ethernet: User ID: 0x30, Synopsys ID: 0x51 [ 3.045559] rk_gmac-dwmac fe010000.ethernet: DWMAC4/5 [ 3.046033] rk_gmac-dwmac fe010000.ethernet: DMA HW capability register suppd [ 3.046747] rk_gmac-dwmac fe010000.ethernet: RX Checksum Offload Engine suppd [ 3.047428] rk_gmac-dwmac fe010000.ethernet: TX Checksum insertion supported [ 3.048062] rk_gmac-dwmac fe010000.ethernet: Wake-Up On Lan supported [ 3.048725] rk_gmac-dwmac fe010000.ethernet: TSO supported [ 3.049229] rk_gmac-dwmac fe010000.ethernet: Enable RX Mitigation via HW Watr [ 3.049954] rk_gmac-dwmac fe010000.ethernet: Enabled RFS Flow TC (entries=10) [ 3.050628] rk_gmac-dwmac fe010000.ethernet: TSO feature enabled [ 3.051176] rk_gmac-dwmac fe010000.ethernet: Using 32/32 bits DMA host/devich [ 3.189988] rk_gmac-dwmac fe2a0000.ethernet: IRQ eth_lpi not found [ 3.190982] rk_gmac-dwmac fe2a0000.ethernet: Looking up phy-supply from devie [ 3.191715] rk_gmac-dwmac fe2a0000.ethernet: Looking up phy-supply property d [ 3.192636] rk_gmac-dwmac fe2a0000.ethernet: no regulator found [ 3.193180] rk_gmac-dwmac fe2a0000.ethernet: clock input or output? (input). [ 3.193818] rk_gmac-dwmac fe2a0000.ethernet: TX delay(0x4f). [ 3.194336] rk_gmac-dwmac fe2a0000.ethernet: RX delay(0xf). [ 3.194885] rk_gmac-dwmac fe2a0000.ethernet: integrated PHY? (no). [ 3.195499] rk_gmac-dwmac fe2a0000.ethernet: clock input from PHY [ 3.201067] rk_gmac-dwmac fe2a0000.ethernet: init for RGMII [ 3.201885] rk_gmac-dwmac fe2a0000.ethernet: User ID: 0x30, Synopsys ID: 0x51 [ 3.202575] rk_gmac-dwmac fe2a0000.ethernet: DWMAC4/5 [ 3.203052] rk_gmac-dwmac fe2a0000.ethernet: DMA HW capability register suppd [ 3.203730] rk_gmac-dwmac fe2a0000.ethernet: RX Checksum Offload Engine suppd [ 3.204405] rk_gmac-dwmac fe2a0000.ethernet: TX Checksum insertion supported [ 3.205039] rk_gmac-dwmac fe2a0000.ethernet: Wake-Up On Lan supported [ 3.205702] rk_gmac-dwmac fe2a0000.ethernet: TSO supported [ 3.206207] rk_gmac-dwmac fe2a0000.ethernet: Enable RX Mitigation via HW Watr [ 3.206969] rk_gmac-dwmac fe2a0000.ethernet: Enabled RFS Flow TC (entries=10) [ 3.207621] rk_gmac-dwmac fe2a0000.ethernet: TSO feature enabled [ 3.208167] rk_gmac-dwmac fe2a0000.ethernet: Using 32/32 bits DMA host/devich [ 80.517694] rk_gmac-dwmac fe010000.ethernet eth0: Register MEM_TYPE_PAGE_POO0 [ 80.520178] rk_gmac-dwmac fe010000.ethernet eth0: PHY [stmmac-1:00] driver [) [ 80.520230] rk_gmac-dwmac fe010000.ethernet eth0: No Safety Features supportd [ 80.520258] rk_gmac-dwmac fe010000.ethernet eth0: IEEE 1588-2008 Advanced Tid [ 80.520514] rk_gmac-dwmac fe010000.ethernet eth0: registered PTP clock [ 80.520898] rk_gmac-dwmac fe010000.ethernet eth0: configuring for phy/rgmii e [ 84.615184] rk_gmac-dwmac fe010000.ethernet eth0: Link is Up - 1Gbps/Full - x root@bpi-r2pro:~# ip a 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group defau0 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group def0 link/ether 76:95:00:96:b3:89 brd ff:ff:ff:ff:ff:ff inet 192.168.0.12/24 scope global eth0 valid_lft forever preferred_lft forever inet6 fe80::7495:ff:fe96:b389/64 scope link valid_lft forever preferred_lft forever 3: eth1: <BROADCAST,MULTICAST> mtu 1504 qdisc noop state DOWN group default qle0 link/ether 76:95:00:96:b3:88 brd ff:ff:ff:ff:ff:ff 4: sit0@NONE: <NOARP> mtu 1480 qdisc noop state DOWN group default qlen 1000 link/sit 0.0.0.0 brd 0.0.0.0 5: lan0@eth1: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc noop state DOWN group0 link/ether 76:95:00:96:b3:88 brd ff:ff:ff:ff:ff:ff 6: lan1@eth1: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc noop state DOWN group0 link/ether 76:95:00:96:b3:88 brd ff:ff:ff:ff:ff:ff 7: lan2@eth1: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc noop state DOWN group0 link/ether 76:95:00:96:b3:88 brd ff:ff:ff:ff:ff:ff 8: lan3@eth1: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc noop state DOWN group0 link/ether 76:95:00:96:b3:88 brd ff:ff:ff:ff:ff:ff root@bpi-r2pro:~# lsusb Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 008 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 007 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 005 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub root@bpi-r2pro:~# lspci 0001:00:00.0 PCI bridge: Rockchip Electronics Co., Ltd RK3568 Remote Signal Pro) 0002:00:00.0 PCI bridge: Rockchip Electronics Co., Ltd RK3568 Remote Signal Pro) root@bpi-r2pro:~# uname -a Linux bpi-r2pro 6.3.0-rc4-bpi-r2pro #1 SMP PREEMPT Mon Apr 10 13:39:18 CEST 202x root@bpi-r2pro:~#
Quoted 3 lines
Quoted 1 line
tested eth1 too...also working. so maybe "only" a evb related dts-change or between rc4 and rc6
Maybe the device tree is not correct on evb...
or you miss any Kconfig option (regulator/power-related)
else make a diff between last working version (dt + config). i see no relevant changes in dts itself between 6.2 and 6.3
regards Frank
_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip
Quoted 76 lines · Frank Wunderlich
Quoted 76 lines
Gesendet: Donnerstag, 13. April 2023 um 11:21 Uhr
Von: "Doug Brewer" <[email protected]>Quoted 69 lines · Frank Wunderlich
Hi
Quoted 67 lines
Gesendet: Donnerstag, 13. April 2023 um 08:28 Uhr
Von: "Johannes Zink" <[email protected]>Quoted 49 lines · Doug Brewer
Hi,
I tested Linux kernel 6.3-rc6 on my rk3568 evaluation board, it seems there are problems with Ethernet, PCIe and usb devices.
First, NICs doesn't work.
rk_gmac-dwmac fe010000.ethernet: IRQ eth_lpi not found rk_gmac-dwmac fe010000.ethernet: no regulator found rk_gmac-dwmac fe010000.ethernet: clock input or output? (output). rk_gmac-dwmac fe010000.ethernet: Can not read property: tx_delay. rk_gmac-dwmac fe010000.ethernet: set tx_delay to 0x30 rk_gmac-dwmac fe010000.ethernet: Can not read property: rx_delay. rk_gmac-dwmac fe010000.ethernet: set rx_delay to 0x10 rk_gmac-dwmac fe010000.ethernet: integrated PHY? (no). rk_gmac-dwmac fe010000.ethernet: init for RGMII_ID rk_gmac-dwmac fe010000.ethernet: User ID: 0x30, Synopsys ID: 0x51 rk_gmac-dwmac fe010000.ethernet: DWMAC4/5 rk_gmac-dwmac fe010000.ethernet: DMA HW capability register suppd rk_gmac-dwmac fe010000.ethernet: RX Checksum Offload Engine suppd rk_gmac-dwmac fe010000.ethernet: TX Checksum insertion supported rk_gmac-dwmac fe010000.ethernet: Wake-Up On Lan supported rk_gmac-dwmac fe010000.ethernet: TSO supported rk_gmac-dwmac fe010000.ethernet: Enable RX Mitigation via HW Watr rk_gmac-dwmac fe010000.ethernet: Enabled RFS Flow TC (entries=10) rk_gmac-dwmac fe010000.ethernet: TSO feature enabled rk_gmac-dwmac fe010000.ethernet: Using 32/32 bits DMA host/devich mdio_bus stmmac-1: MDIO device at address 0 is missing. rk_gmac-dwmac fe2a0000.ethernet: IRQ eth_lpi not found rk_gmac-dwmac fe2a0000.ethernet: no regulator found rk_gmac-dwmac fe2a0000.ethernet: clock input or output? (output). rk_gmac-dwmac fe2a0000.ethernet: Can not read property: tx_delay. rk_gmac-dwmac fe2a0000.ethernet: set tx_delay to 0x30 rk_gmac-dwmac fe2a0000.ethernet: Can not read property: rx_delay. rk_gmac-dwmac fe2a0000.ethernet: set rx_delay to 0x10 rk_gmac-dwmac fe2a0000.ethernet: integrated PHY? (no). rk_gmac-dwmac fe2a0000.ethernet: init for RGMII_ID rk_gmac-dwmac fe2a0000.ethernet: User ID: 0x30, Synopsys ID: 0x51 rk_gmac-dwmac fe2a0000.ethernet: DWMAC4/5 rk_gmac-dwmac fe2a0000.ethernet: DMA HW capability register suppd rk_gmac-dwmac fe2a0000.ethernet: RX Checksum Offload Engine suppd rk_gmac-dwmac fe2a0000.ethernet: TX Checksum insertion supported rk_gmac-dwmac fe2a0000.ethernet: Wake-Up On Lan supported rk_gmac-dwmac fe2a0000.ethernet: TSO supported rk_gmac-dwmac fe2a0000.ethernet: Enable RX Mitigation via HW Watr rk_gmac-dwmac fe2a0000.ethernet: Enabled RFS Flow TC (entries=10) rk_gmac-dwmac fe2a0000.ethernet: TSO feature enabled rk_gmac-dwmac fe2a0000.ethernet: Using 32/32 bits DMA host/devich mdio_bus stmmac-0: MDIO device at address 0 is missing.Quoted 8 lines
rk_gmac-dwmac fe010000.ethernet eth0: Register
MEM_TYPE_PAGE_POO0rk_gmac-dwmac fe010000.ethernet eth0:__stmmac_open: Cannot atta)Second, running 'lspci' and 'lsusb' doesn't see any devices on PCIe and USB. I guess the device tree might be updated. Anyone has idea how to fix it? Thanks.
- Doug
I've seen similar errors on other boards when the phy is not powered or does not have a clock supplied. Could you check your DT if there is any diffs in the phy-supply or any gpio-Hog pulling the enable of a regulator that might enable the phy? Also you could check if you have all the required regulator drivers available and probed.
Quoted 8 lines
Quoted 6 lines
Quoted 4 lines
Quoted 2 lines
Best regards
Johannesi tested 6.3.0-rc4 on my banaanpi r2pro and there it seem no problem...do you have the issue on rc4 too?
I just tested 6.3.0-rc4 on my rk3568 evb, no luck.
was 6.2.0 working?
6.2.0 is not working.
Quoted 1 line
you should upload your full dmesg and .config to pastebin or similar and send the linke here
Fair enough.
dmesg: http://sprunge.us/LNFvdL
.config: http://sprunge.us/vPdrLf
Quoted 140 lines
Quoted 140 lines
# dmesg |grep rk_gmac [ 11.381071] rk_gmac-dwmac fe010000.ethernet: IRQ eth_lpi not found [ 11.381892] rk_gmac-dwmac fe010000.ethernet: no regulator found [ 11.382529] rk_gmac-dwmac fe010000.ethernet: clock input or output? (output). [ 11.383178] rk_gmac-dwmac fe010000.ethernet: Can not read property: tx_delay. [ 11.383815] rk_gmac-dwmac fe010000.ethernet: set tx_delay to 0x30 [ 11.384373] rk_gmac-dwmac fe010000.ethernet: Can not read property: rx_delay. [ 11.385008] rk_gmac-dwmac fe010000.ethernet: set rx_delay to 0x10 [ 11.385561] rk_gmac-dwmac fe010000.ethernet: integrated PHY? (no). [ 11.396162] rk_gmac-dwmac fe010000.ethernet: init for RGMII_ID [ 11.400201] rk_gmac-dwmac fe010000.ethernet: User ID: 0x30, Synopsys ID: 0x51 [ 11.400878] rk_gmac-dwmac fe010000.ethernet: DWMAC4/5 [ 11.401349] rk_gmac-dwmac fe010000.ethernet: DMA HW capability register suppd [ 11.402067] rk_gmac-dwmac fe010000.ethernet: RX Checksum Offload Engine suppd [ 11.402755] rk_gmac-dwmac fe010000.ethernet: TX Checksum insertion supported [ 11.403401] rk_gmac-dwmac fe010000.ethernet: Wake-Up On Lan supported [ 11.404185] rk_gmac-dwmac fe010000.ethernet: TSO supported [ 11.406883] rk_gmac-dwmac fe010000.ethernet: Enable RX Mitigation via HW Watr [ 11.407964] rk_gmac-dwmac fe010000.ethernet: Enabled RFS Flow TC (entries=10) [ 11.408624] rk_gmac-dwmac fe010000.ethernet: TSO feature enabled [ 11.411098] rk_gmac-dwmac fe010000.ethernet: Using 32/32 bits DMA host/devich [ 11.421076] rk_gmac-dwmac fe2a0000.ethernet: IRQ eth_lpi not found [ 11.422308] rk_gmac-dwmac fe2a0000.ethernet: no regulator found [ 11.422870] rk_gmac-dwmac fe2a0000.ethernet: clock input or output? (output). [ 11.423515] rk_gmac-dwmac fe2a0000.ethernet: Can not read property: tx_delay. [ 11.425161] rk_gmac-dwmac fe2a0000.ethernet: set tx_delay to 0x30 [ 11.425862] rk_gmac-dwmac fe2a0000.ethernet: Can not read property: rx_delay. [ 11.426731] rk_gmac-dwmac fe2a0000.ethernet: set rx_delay to 0x10 [ 11.427430] rk_gmac-dwmac fe2a0000.ethernet: integrated PHY? (no). [ 11.433094] rk_gmac-dwmac fe2a0000.ethernet: init for RGMII_ID [ 11.445612] rk_gmac-dwmac fe2a0000.ethernet: User ID: 0x30, Synopsys ID: 0x51 [ 11.446753] rk_gmac-dwmac fe2a0000.ethernet: DWMAC4/5 [ 11.447265] rk_gmac-dwmac fe2a0000.ethernet: DMA HW capability register suppd [ 11.447940] rk_gmac-dwmac fe2a0000.ethernet: RX Checksum Offload Engine suppd [ 11.448612] rk_gmac-dwmac fe2a0000.ethernet: TX Checksum insertion supported [ 11.449536] rk_gmac-dwmac fe2a0000.ethernet: Wake-Up On Lan supported [ 11.452947] rk_gmac-dwmac fe2a0000.ethernet: TSO supported [ 11.453468] rk_gmac-dwmac fe2a0000.ethernet: Enable RX Mitigation via HW Watr [ 11.454401] rk_gmac-dwmac fe2a0000.ethernet: Enabled RFS Flow TC (entries=10) [ 11.455054] rk_gmac-dwmac fe2a0000.ethernet: TSO feature enabled [ 11.456887] rk_gmac-dwmac fe2a0000.ethernet: Using 32/32 bits DMA host/devich [ 12.340615] rk_gmac-dwmac fe010000.ethernet eth0: Register MEM_TYPE_PAGE_POO0 [ 12.342575] rk_gmac-dwmac fe010000.ethernet eth0: no phy found [ 12.343121] rk_gmac-dwmac fe010000.ethernet eth0: __stmmac_open: Cannot atta)Quoted 92 lines
root@bpi-r2pro:~# dmesg | grep rk_gmac-dwmac [ 3.033681] rk_gmac-dwmac fe010000.ethernet: IRQ eth_lpi not found [ 3.034528] rk_gmac-dwmac fe010000.ethernet: Looking up phy-supply from devie [ 3.035243] rk_gmac-dwmac fe010000.ethernet: Looking up phy-supply property d [ 3.036170] rk_gmac-dwmac fe010000.ethernet: no regulator found [ 3.036713] rk_gmac-dwmac fe010000.ethernet: clock input or output? (output). [ 3.037361] rk_gmac-dwmac fe010000.ethernet: TX delay(0x3c). [ 3.037877] rk_gmac-dwmac fe010000.ethernet: RX delay(0x2f). [ 3.038398] rk_gmac-dwmac fe010000.ethernet: integrated PHY? (no). [ 3.044063] rk_gmac-dwmac fe010000.ethernet: init for RGMII [ 3.044896] rk_gmac-dwmac fe010000.ethernet: User ID: 0x30, Synopsys ID: 0x51 [ 3.045559] rk_gmac-dwmac fe010000.ethernet: DWMAC4/5 [ 3.046033] rk_gmac-dwmac fe010000.ethernet: DMA HW capability register suppd [ 3.046747] rk_gmac-dwmac fe010000.ethernet: RX Checksum Offload Engine suppd [ 3.047428] rk_gmac-dwmac fe010000.ethernet: TX Checksum insertion supported [ 3.048062] rk_gmac-dwmac fe010000.ethernet: Wake-Up On Lan supported [ 3.048725] rk_gmac-dwmac fe010000.ethernet: TSO supported [ 3.049229] rk_gmac-dwmac fe010000.ethernet: Enable RX Mitigation via HW Watr [ 3.049954] rk_gmac-dwmac fe010000.ethernet: Enabled RFS Flow TC (entries=10) [ 3.050628] rk_gmac-dwmac fe010000.ethernet: TSO feature enabled [ 3.051176] rk_gmac-dwmac fe010000.ethernet: Using 32/32 bits DMA host/devich [ 3.189988] rk_gmac-dwmac fe2a0000.ethernet: IRQ eth_lpi not found [ 3.190982] rk_gmac-dwmac fe2a0000.ethernet: Looking up phy-supply from devie [ 3.191715] rk_gmac-dwmac fe2a0000.ethernet: Looking up phy-supply property d [ 3.192636] rk_gmac-dwmac fe2a0000.ethernet: no regulator found [ 3.193180] rk_gmac-dwmac fe2a0000.ethernet: clock input or output? (input). [ 3.193818] rk_gmac-dwmac fe2a0000.ethernet: TX delay(0x4f). [ 3.194336] rk_gmac-dwmac fe2a0000.ethernet: RX delay(0xf). [ 3.194885] rk_gmac-dwmac fe2a0000.ethernet: integrated PHY? (no). [ 3.195499] rk_gmac-dwmac fe2a0000.ethernet: clock input from PHY [ 3.201067] rk_gmac-dwmac fe2a0000.ethernet: init for RGMII [ 3.201885] rk_gmac-dwmac fe2a0000.ethernet: User ID: 0x30, Synopsys ID: 0x51 [ 3.202575] rk_gmac-dwmac fe2a0000.ethernet: DWMAC4/5 [ 3.203052] rk_gmac-dwmac fe2a0000.ethernet: DMA HW capability register suppd [ 3.203730] rk_gmac-dwmac fe2a0000.ethernet: RX Checksum Offload Engine suppd [ 3.204405] rk_gmac-dwmac fe2a0000.ethernet: TX Checksum insertion supported [ 3.205039] rk_gmac-dwmac fe2a0000.ethernet: Wake-Up On Lan supported [ 3.205702] rk_gmac-dwmac fe2a0000.ethernet: TSO supported [ 3.206207] rk_gmac-dwmac fe2a0000.ethernet: Enable RX Mitigation via HW Watr [ 3.206969] rk_gmac-dwmac fe2a0000.ethernet: Enabled RFS Flow TC (entries=10) [ 3.207621] rk_gmac-dwmac fe2a0000.ethernet: TSO feature enabled [ 3.208167] rk_gmac-dwmac fe2a0000.ethernet: Using 32/32 bits DMA host/devich [ 80.517694] rk_gmac-dwmac fe010000.ethernet eth0: Register MEM_TYPE_PAGE_POO0 [ 80.520178] rk_gmac-dwmac fe010000.ethernet eth0: PHY [stmmac-1:00] driver [) [ 80.520230] rk_gmac-dwmac fe010000.ethernet eth0: No Safety Features supportd [ 80.520258] rk_gmac-dwmac fe010000.ethernet eth0: IEEE 1588-2008 Advanced Tid [ 80.520514] rk_gmac-dwmac fe010000.ethernet eth0: registered PTP clock [ 80.520898] rk_gmac-dwmac fe010000.ethernet eth0: configuring for phy/rgmii e [ 84.615184] rk_gmac-dwmac fe010000.ethernet eth0: Link is Up - 1Gbps/Full - x root@bpi-r2pro:~# ip a 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group defau0 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group def0 link/ether 76:95:00:96:b3:89 brd ff:ff:ff:ff:ff:ff inet 192.168.0.12/24 scope global eth0 valid_lft forever preferred_lft forever inet6 fe80::7495:ff:fe96:b389/64 scope link valid_lft forever preferred_lft forever 3: eth1: <BROADCAST,MULTICAST> mtu 1504 qdisc noop state DOWN group default qle0 link/ether 76:95:00:96:b3:88 brd ff:ff:ff:ff:ff:ff 4: sit0@NONE: <NOARP> mtu 1480 qdisc noop state DOWN group default qlen 1000 link/sit 0.0.0.0 brd 0.0.0.0 5: lan0@eth1: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc noop state DOWN group0 link/ether 76:95:00:96:b3:88 brd ff:ff:ff:ff:ff:ff 6: lan1@eth1: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc noop state DOWN group0 link/ether 76:95:00:96:b3:88 brd ff:ff:ff:ff:ff:ff 7: lan2@eth1: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc noop state DOWN group0 link/ether 76:95:00:96:b3:88 brd ff:ff:ff:ff:ff:ff 8: lan3@eth1: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc noop state DOWN group0 link/ether 76:95:00:96:b3:88 brd ff:ff:ff:ff:ff:ff root@bpi-r2pro:~# lsusb Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 008 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 007 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 005 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub root@bpi-r2pro:~# lspci 0001:00:00.0 PCI bridge: Rockchip Electronics Co., Ltd RK3568 Remote Signal Pro) 0002:00:00.0 PCI bridge: Rockchip Electronics Co., Ltd RK3568 Remote Signal Pro) root@bpi-r2pro:~# uname -a Linux bpi-r2pro 6.3.0-rc4-bpi-r2pro #1 SMP PREEMPT Mon Apr 10 13:39:18 CEST 202x root@bpi-r2pro:~#tested eth1 too...also working. so maybe "only" a evb related dts-change or between rc4 and rc6
Quoted 7 lines
Quoted 1 line
Maybe the device tree is not correct on evb...
or you miss any
Kconfigoption (regulator/power-related)else make a diff between last working version (dt + config). i see no relevant changes in dts itself between 6.2 and 6.3
regards Frank
Thanks!
Doug
_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip
Hi Doug,
Quoted 85 lines · Doug Brewer
Quoted 83 lines · Frank Wunderlich
Quoted 82 lines
Gesendet: Donnerstag, 13. April 2023 um 11:21 Uhr
Von: "Doug Brewer" <[email protected]>Quoted 69 lines · Frank Wunderlich
Hi
Quoted 67 lines
Gesendet: Donnerstag, 13. April 2023 um 08:28 Uhr
Von: "Johannes Zink" <[email protected]>Quoted 49 lines · Doug Brewer
Hi,
I tested Linux kernel 6.3-rc6 on my rk3568 evaluation board, it seems there are problems with Ethernet, PCIe and usb devices.
First, NICs doesn't work.
rk_gmac-dwmac fe010000.ethernet: IRQ eth_lpi not found rk_gmac-dwmac fe010000.ethernet: no regulator found rk_gmac-dwmac fe010000.ethernet: clock input or output? (output). rk_gmac-dwmac fe010000.ethernet: Can not read property: tx_delay. rk_gmac-dwmac fe010000.ethernet: set tx_delay to 0x30 rk_gmac-dwmac fe010000.ethernet: Can not read property: rx_delay. rk_gmac-dwmac fe010000.ethernet: set rx_delay to 0x10 rk_gmac-dwmac fe010000.ethernet: integrated PHY? (no). rk_gmac-dwmac fe010000.ethernet: init for RGMII_ID rk_gmac-dwmac fe010000.ethernet: User ID: 0x30, Synopsys ID: 0x51 rk_gmac-dwmac fe010000.ethernet: DWMAC4/5 rk_gmac-dwmac fe010000.ethernet: DMA HW capability register suppd rk_gmac-dwmac fe010000.ethernet: RX Checksum Offload Engine suppd rk_gmac-dwmac fe010000.ethernet: TX Checksum insertion supported rk_gmac-dwmac fe010000.ethernet: Wake-Up On Lan supported rk_gmac-dwmac fe010000.ethernet: TSO supported rk_gmac-dwmac fe010000.ethernet: Enable RX Mitigation via HW Watr rk_gmac-dwmac fe010000.ethernet: Enabled RFS Flow TC (entries=10) rk_gmac-dwmac fe010000.ethernet: TSO feature enabled rk_gmac-dwmac fe010000.ethernet: Using 32/32 bits DMA host/devich mdio_bus stmmac-1: MDIO device at address 0 is missing. rk_gmac-dwmac fe2a0000.ethernet: IRQ eth_lpi not found rk_gmac-dwmac fe2a0000.ethernet: no regulator found rk_gmac-dwmac fe2a0000.ethernet: clock input or output? (output). rk_gmac-dwmac fe2a0000.ethernet: Can not read property: tx_delay. rk_gmac-dwmac fe2a0000.ethernet: set tx_delay to 0x30 rk_gmac-dwmac fe2a0000.ethernet: Can not read property: rx_delay. rk_gmac-dwmac fe2a0000.ethernet: set rx_delay to 0x10 rk_gmac-dwmac fe2a0000.ethernet: integrated PHY? (no). rk_gmac-dwmac fe2a0000.ethernet: init for RGMII_ID rk_gmac-dwmac fe2a0000.ethernet: User ID: 0x30, Synopsys ID: 0x51 rk_gmac-dwmac fe2a0000.ethernet: DWMAC4/5 rk_gmac-dwmac fe2a0000.ethernet: DMA HW capability register suppd rk_gmac-dwmac fe2a0000.ethernet: RX Checksum Offload Engine suppd rk_gmac-dwmac fe2a0000.ethernet: TX Checksum insertion supported rk_gmac-dwmac fe2a0000.ethernet: Wake-Up On Lan supported rk_gmac-dwmac fe2a0000.ethernet: TSO supported rk_gmac-dwmac fe2a0000.ethernet: Enable RX Mitigation via HW Watr rk_gmac-dwmac fe2a0000.ethernet: Enabled RFS Flow TC (entries=10) rk_gmac-dwmac fe2a0000.ethernet: TSO feature enabled rk_gmac-dwmac fe2a0000.ethernet: Using 32/32 bits DMA host/devich mdio_bus stmmac-0: MDIO device at address 0 is missing.Quoted 8 lines
rk_gmac-dwmac fe010000.ethernet eth0: Register
MEM_TYPE_PAGE_POO0rk_gmac-dwmac fe010000.ethernet eth0:__stmmac_open: Cannot atta)Second, running 'lspci' and 'lsusb' doesn't see any devices on PCIe and USB. I guess the device tree might be updated. Anyone has idea how to fix it? Thanks.
- Doug
I've seen similar errors on other boards when the phy is not powered or does not have a clock supplied. Could you check your DT if there is any diffs in the phy-supply or any gpio-Hog pulling the enable of a regulator that might enable the phy? Also you could check if you have all the required regulator drivers available and probed.
Quoted 4 lines
Quoted 2 lines
Best regards
Johannesi tested 6.3.0-rc4 on my banaanpi r2pro and there it seem no problem...do you have the issue on rc4 too?
I just tested 6.3.0-rc4 on my rk3568 evb, no luck.
Quoted 8 lines
Quoted 1 line
was 6.2.0 working?
6.2.0 is not working.
Quoted 1 line
you should upload your full dmesg and .config to pastebin or similar and send the linke here
Fair enough.
dmesg: http://sprunge.us/LNFvdL
Is this really the complete log (which would mean that your board hangs after "Cannot attach to PHY")? Maybe you are booting via NFS and your rootfs is not found, but above you state that you were able to run lsusb and lspci.
Also, can you check whether
cat /sys/kernel/debug/devices_deferred
shows a missing dependency?
Best regards,
Michael
Quoted 150 lines
.config: http://sprunge.us/vPdrLf
Quoted 140 lines
Quoted 140 lines
# dmesg |grep rk_gmac [ 11.381071] rk_gmac-dwmac fe010000.ethernet: IRQ eth_lpi not found [ 11.381892] rk_gmac-dwmac fe010000.ethernet: no regulator found [ 11.382529] rk_gmac-dwmac fe010000.ethernet: clock input or output? (output). [ 11.383178] rk_gmac-dwmac fe010000.ethernet: Can not read property: tx_delay. [ 11.383815] rk_gmac-dwmac fe010000.ethernet: set tx_delay to 0x30 [ 11.384373] rk_gmac-dwmac fe010000.ethernet: Can not read property: rx_delay. [ 11.385008] rk_gmac-dwmac fe010000.ethernet: set rx_delay to 0x10 [ 11.385561] rk_gmac-dwmac fe010000.ethernet: integrated PHY? (no). [ 11.396162] rk_gmac-dwmac fe010000.ethernet: init for RGMII_ID [ 11.400201] rk_gmac-dwmac fe010000.ethernet: User ID: 0x30, Synopsys ID: 0x51 [ 11.400878] rk_gmac-dwmac fe010000.ethernet: DWMAC4/5 [ 11.401349] rk_gmac-dwmac fe010000.ethernet: DMA HW capability register suppd [ 11.402067] rk_gmac-dwmac fe010000.ethernet: RX Checksum Offload Engine suppd [ 11.402755] rk_gmac-dwmac fe010000.ethernet: TX Checksum insertion supported [ 11.403401] rk_gmac-dwmac fe010000.ethernet: Wake-Up On Lan supported [ 11.404185] rk_gmac-dwmac fe010000.ethernet: TSO supported [ 11.406883] rk_gmac-dwmac fe010000.ethernet: Enable RX Mitigation via HW Watr [ 11.407964] rk_gmac-dwmac fe010000.ethernet: Enabled RFS Flow TC (entries=10) [ 11.408624] rk_gmac-dwmac fe010000.ethernet: TSO feature enabled [ 11.411098] rk_gmac-dwmac fe010000.ethernet: Using 32/32 bits DMA host/devich [ 11.421076] rk_gmac-dwmac fe2a0000.ethernet: IRQ eth_lpi not found [ 11.422308] rk_gmac-dwmac fe2a0000.ethernet: no regulator found [ 11.422870] rk_gmac-dwmac fe2a0000.ethernet: clock input or output? (output). [ 11.423515] rk_gmac-dwmac fe2a0000.ethernet: Can not read property: tx_delay. [ 11.425161] rk_gmac-dwmac fe2a0000.ethernet: set tx_delay to 0x30 [ 11.425862] rk_gmac-dwmac fe2a0000.ethernet: Can not read property: rx_delay. [ 11.426731] rk_gmac-dwmac fe2a0000.ethernet: set rx_delay to 0x10 [ 11.427430] rk_gmac-dwmac fe2a0000.ethernet: integrated PHY? (no). [ 11.433094] rk_gmac-dwmac fe2a0000.ethernet: init for RGMII_ID [ 11.445612] rk_gmac-dwmac fe2a0000.ethernet: User ID: 0x30, Synopsys ID: 0x51 [ 11.446753] rk_gmac-dwmac fe2a0000.ethernet: DWMAC4/5 [ 11.447265] rk_gmac-dwmac fe2a0000.ethernet: DMA HW capability register suppd [ 11.447940] rk_gmac-dwmac fe2a0000.ethernet: RX Checksum Offload Engine suppd [ 11.448612] rk_gmac-dwmac fe2a0000.ethernet: TX Checksum insertion supported [ 11.449536] rk_gmac-dwmac fe2a0000.ethernet: Wake-Up On Lan supported [ 11.452947] rk_gmac-dwmac fe2a0000.ethernet: TSO supported [ 11.453468] rk_gmac-dwmac fe2a0000.ethernet: Enable RX Mitigation via HW Watr [ 11.454401] rk_gmac-dwmac fe2a0000.ethernet: Enabled RFS Flow TC (entries=10) [ 11.455054] rk_gmac-dwmac fe2a0000.ethernet: TSO feature enabled [ 11.456887] rk_gmac-dwmac fe2a0000.ethernet: Using 32/32 bits DMA host/devich [ 12.340615] rk_gmac-dwmac fe010000.ethernet eth0: Register MEM_TYPE_PAGE_POO0 [ 12.342575] rk_gmac-dwmac fe010000.ethernet eth0: no phy found [ 12.343121] rk_gmac-dwmac fe010000.ethernet eth0: __stmmac_open: Cannot atta)Quoted 92 lines
root@bpi-r2pro:~# dmesg | grep rk_gmac-dwmac [ 3.033681] rk_gmac-dwmac fe010000.ethernet: IRQ eth_lpi not found [ 3.034528] rk_gmac-dwmac fe010000.ethernet: Looking up phy-supply from devie [ 3.035243] rk_gmac-dwmac fe010000.ethernet: Looking up phy-supply property d [ 3.036170] rk_gmac-dwmac fe010000.ethernet: no regulator found [ 3.036713] rk_gmac-dwmac fe010000.ethernet: clock input or output? (output). [ 3.037361] rk_gmac-dwmac fe010000.ethernet: TX delay(0x3c). [ 3.037877] rk_gmac-dwmac fe010000.ethernet: RX delay(0x2f). [ 3.038398] rk_gmac-dwmac fe010000.ethernet: integrated PHY? (no). [ 3.044063] rk_gmac-dwmac fe010000.ethernet: init for RGMII [ 3.044896] rk_gmac-dwmac fe010000.ethernet: User ID: 0x30, Synopsys ID: 0x51 [ 3.045559] rk_gmac-dwmac fe010000.ethernet: DWMAC4/5 [ 3.046033] rk_gmac-dwmac fe010000.ethernet: DMA HW capability register suppd [ 3.046747] rk_gmac-dwmac fe010000.ethernet: RX Checksum Offload Engine suppd [ 3.047428] rk_gmac-dwmac fe010000.ethernet: TX Checksum insertion supported [ 3.048062] rk_gmac-dwmac fe010000.ethernet: Wake-Up On Lan supported [ 3.048725] rk_gmac-dwmac fe010000.ethernet: TSO supported [ 3.049229] rk_gmac-dwmac fe010000.ethernet: Enable RX Mitigation via HW Watr [ 3.049954] rk_gmac-dwmac fe010000.ethernet: Enabled RFS Flow TC (entries=10) [ 3.050628] rk_gmac-dwmac fe010000.ethernet: TSO feature enabled [ 3.051176] rk_gmac-dwmac fe010000.ethernet: Using 32/32 bits DMA host/devich [ 3.189988] rk_gmac-dwmac fe2a0000.ethernet: IRQ eth_lpi not found [ 3.190982] rk_gmac-dwmac fe2a0000.ethernet: Looking up phy-supply from devie [ 3.191715] rk_gmac-dwmac fe2a0000.ethernet: Looking up phy-supply property d [ 3.192636] rk_gmac-dwmac fe2a0000.ethernet: no regulator found [ 3.193180] rk_gmac-dwmac fe2a0000.ethernet: clock input or output? (input). [ 3.193818] rk_gmac-dwmac fe2a0000.ethernet: TX delay(0x4f). [ 3.194336] rk_gmac-dwmac fe2a0000.ethernet: RX delay(0xf). [ 3.194885] rk_gmac-dwmac fe2a0000.ethernet: integrated PHY? (no). [ 3.195499] rk_gmac-dwmac fe2a0000.ethernet: clock input from PHY [ 3.201067] rk_gmac-dwmac fe2a0000.ethernet: init for RGMII [ 3.201885] rk_gmac-dwmac fe2a0000.ethernet: User ID: 0x30, Synopsys ID: 0x51 [ 3.202575] rk_gmac-dwmac fe2a0000.ethernet: DWMAC4/5 [ 3.203052] rk_gmac-dwmac fe2a0000.ethernet: DMA HW capability register suppd [ 3.203730] rk_gmac-dwmac fe2a0000.ethernet: RX Checksum Offload Engine suppd [ 3.204405] rk_gmac-dwmac fe2a0000.ethernet: TX Checksum insertion supported [ 3.205039] rk_gmac-dwmac fe2a0000.ethernet: Wake-Up On Lan supported [ 3.205702] rk_gmac-dwmac fe2a0000.ethernet: TSO supported [ 3.206207] rk_gmac-dwmac fe2a0000.ethernet: Enable RX Mitigation via HW Watr [ 3.206969] rk_gmac-dwmac fe2a0000.ethernet: Enabled RFS Flow TC (entries=10) [ 3.207621] rk_gmac-dwmac fe2a0000.ethernet: TSO feature enabled [ 3.208167] rk_gmac-dwmac fe2a0000.ethernet: Using 32/32 bits DMA host/devich [ 80.517694] rk_gmac-dwmac fe010000.ethernet eth0: Register MEM_TYPE_PAGE_POO0 [ 80.520178] rk_gmac-dwmac fe010000.ethernet eth0: PHY [stmmac-1:00] driver [) [ 80.520230] rk_gmac-dwmac fe010000.ethernet eth0: No Safety Features supportd [ 80.520258] rk_gmac-dwmac fe010000.ethernet eth0: IEEE 1588-2008 Advanced Tid [ 80.520514] rk_gmac-dwmac fe010000.ethernet eth0: registered PTP clock [ 80.520898] rk_gmac-dwmac fe010000.ethernet eth0: configuring for phy/rgmii e [ 84.615184] rk_gmac-dwmac fe010000.ethernet eth0: Link is Up - 1Gbps/Full - x root@bpi-r2pro:~# ip a 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group defau0 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group def0 link/ether 76:95:00:96:b3:89 brd ff:ff:ff:ff:ff:ff inet 192.168.0.12/24 scope global eth0 valid_lft forever preferred_lft forever inet6 fe80::7495:ff:fe96:b389/64 scope link valid_lft forever preferred_lft forever 3: eth1: <BROADCAST,MULTICAST> mtu 1504 qdisc noop state DOWN group default qle0 link/ether 76:95:00:96:b3:88 brd ff:ff:ff:ff:ff:ff 4: sit0@NONE: <NOARP> mtu 1480 qdisc noop state DOWN group default qlen 1000 link/sit 0.0.0.0 brd 0.0.0.0 5: lan0@eth1: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc noop state DOWN group0 link/ether 76:95:00:96:b3:88 brd ff:ff:ff:ff:ff:ff 6: lan1@eth1: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc noop state DOWN group0 link/ether 76:95:00:96:b3:88 brd ff:ff:ff:ff:ff:ff 7: lan2@eth1: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc noop state DOWN group0 link/ether 76:95:00:96:b3:88 brd ff:ff:ff:ff:ff:ff 8: lan3@eth1: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc noop state DOWN group0 link/ether 76:95:00:96:b3:88 brd ff:ff:ff:ff:ff:ff root@bpi-r2pro:~# lsusb Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 008 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 007 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 005 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub root@bpi-r2pro:~# lspci 0001:00:00.0 PCI bridge: Rockchip Electronics Co., Ltd RK3568 Remote Signal Pro) 0002:00:00.0 PCI bridge: Rockchip Electronics Co., Ltd RK3568 Remote Signal Pro) root@bpi-r2pro:~# uname -a Linux bpi-r2pro 6.3.0-rc4-bpi-r2pro #1 SMP PREEMPT Mon Apr 10 13:39:18 CEST 202x root@bpi-r2pro:~#tested eth1 too...also working. so maybe "only" a evb related dts-change or between rc4 and rc6
Quoted 7 lines
Quoted 1 line
Maybe the device tree is not correct on evb...
or you miss any
Kconfigoption (regulator/power-related)else make a diff between last working version (dt + config). i see no relevant changes in dts itself between 6.2 and 6.3
regards Frank
Quoted 7 lines
Thanks!
Doug_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip
_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip
Quoted 2 lines · Michael Riesch
Hi Doug,
Hi Michael,
Quoted 92 lines · Doug Brewer
Quoted 91 lines
Quoted 76 lines · Frank Wunderlich
Quoted 76 lines
Gesendet: Donnerstag, 13. April 2023 um 11:21 Uhr
Von: "Doug Brewer" <[email protected]>Quoted 69 lines · Frank Wunderlich
Hi
Quoted 67 lines
Gesendet: Donnerstag, 13. April 2023 um 08:28 Uhr
Von: "Johannes Zink" <[email protected]>Quoted 49 lines · Doug Brewer
Hi,
I tested Linux kernel 6.3-rc6 on my rk3568 evaluation board, it seems there are problems with Ethernet, PCIe and usb devices.
First, NICs doesn't work.
rk_gmac-dwmac fe010000.ethernet: IRQ eth_lpi not found rk_gmac-dwmac fe010000.ethernet: no regulator found rk_gmac-dwmac fe010000.ethernet: clock input or output? (output). rk_gmac-dwmac fe010000.ethernet: Can not read property: tx_delay. rk_gmac-dwmac fe010000.ethernet: set tx_delay to 0x30 rk_gmac-dwmac fe010000.ethernet: Can not read property: rx_delay. rk_gmac-dwmac fe010000.ethernet: set rx_delay to 0x10 rk_gmac-dwmac fe010000.ethernet: integrated PHY? (no). rk_gmac-dwmac fe010000.ethernet: init for RGMII_ID rk_gmac-dwmac fe010000.ethernet: User ID: 0x30, Synopsys ID: 0x51 rk_gmac-dwmac fe010000.ethernet: DWMAC4/5 rk_gmac-dwmac fe010000.ethernet: DMA HW capability register suppd rk_gmac-dwmac fe010000.ethernet: RX Checksum Offload Engine suppd rk_gmac-dwmac fe010000.ethernet: TX Checksum insertion supported rk_gmac-dwmac fe010000.ethernet: Wake-Up On Lan supported rk_gmac-dwmac fe010000.ethernet: TSO supported rk_gmac-dwmac fe010000.ethernet: Enable RX Mitigation via HW Watr rk_gmac-dwmac fe010000.ethernet: Enabled RFS Flow TC (entries=10) rk_gmac-dwmac fe010000.ethernet: TSO feature enabled rk_gmac-dwmac fe010000.ethernet: Using 32/32 bits DMA host/devich mdio_bus stmmac-1: MDIO device at address 0 is missing. rk_gmac-dwmac fe2a0000.ethernet: IRQ eth_lpi not found rk_gmac-dwmac fe2a0000.ethernet: no regulator found rk_gmac-dwmac fe2a0000.ethernet: clock input or output? (output). rk_gmac-dwmac fe2a0000.ethernet: Can not read property: tx_delay. rk_gmac-dwmac fe2a0000.ethernet: set tx_delay to 0x30 rk_gmac-dwmac fe2a0000.ethernet: Can not read property: rx_delay. rk_gmac-dwmac fe2a0000.ethernet: set rx_delay to 0x10 rk_gmac-dwmac fe2a0000.ethernet: integrated PHY? (no). rk_gmac-dwmac fe2a0000.ethernet: init for RGMII_ID rk_gmac-dwmac fe2a0000.ethernet: User ID: 0x30, Synopsys ID: 0x51 rk_gmac-dwmac fe2a0000.ethernet: DWMAC4/5 rk_gmac-dwmac fe2a0000.ethernet: DMA HW capability register suppd rk_gmac-dwmac fe2a0000.ethernet: RX Checksum Offload Engine suppd rk_gmac-dwmac fe2a0000.ethernet: TX Checksum insertion supported rk_gmac-dwmac fe2a0000.ethernet: Wake-Up On Lan supported rk_gmac-dwmac fe2a0000.ethernet: TSO supported rk_gmac-dwmac fe2a0000.ethernet: Enable RX Mitigation via HW Watr rk_gmac-dwmac fe2a0000.ethernet: Enabled RFS Flow TC (entries=10) rk_gmac-dwmac fe2a0000.ethernet: TSO feature enabled rk_gmac-dwmac fe2a0000.ethernet: Using 32/32 bits DMA host/devich mdio_bus stmmac-0: MDIO device at address 0 is missing.Quoted 8 lines
rk_gmac-dwmac fe010000.ethernet eth0: Register
MEM_TYPE_PAGE_POO0rk_gmac-dwmac fe010000.ethernet eth0:__stmmac_open: Cannot atta)Second, running 'lspci' and 'lsusb' doesn't see any devices on PCIe and USB. I guess the device tree might be updated. Anyone has idea how to fix it? Thanks.
- Doug
I've seen similar errors on other boards when the phy is not powered or does not have a clock supplied. Could you check your DT if there is any diffs in the phy-supply or any gpio-Hog pulling the enable of a regulator that might enable the phy? Also you could check if you have all the required regulator drivers available and probed.
Quoted 8 lines
Quoted 6 lines
Quoted 4 lines
Quoted 2 lines
Best regards
Johannesi tested 6.3.0-rc4 on my banaanpi r2pro and there it seem no problem...do you have the issue on rc4 too?
I just tested 6.3.0-rc4 on my rk3568 evb, no luck.
was 6.2.0 working?
6.2.0 is not working.
Quoted 1 line
you should upload your full dmesg and .config to pastebin or similar and send the linke here
Quoted 7 lines
Quoted 2 lines
Fair enough.
dmesg: http://sprunge.us/LNFvdLIs this really the complete log (which would mean that your board hangs after "Cannot attach to PHY")? Maybe you are booting via NFS and your rootfs is not found, but above you state that you were able to run lsusb and lspci.
This is the output of executing dmesg. It's the complete log:
http://sprunge.us/KQyTVi
I'm booting Linux from SD card.
Quoted 5 lines
Also, can you check whether
cat
/sys/kernel/debug/devices_deferredshows a missing dependency?
No.
# cat /sys/kernel/debug/devices_deferred #
Quoted 2 lines
Best regards,
Michael
Thanks,
Doug
Quoted 158 lines
Quoted 150 lines
.config: http://sprunge.us/vPdrLf
Quoted 140 lines
Quoted 140 lines
# dmesg |grep rk_gmac [ 11.381071] rk_gmac-dwmac fe010000.ethernet: IRQ eth_lpi not found [ 11.381892] rk_gmac-dwmac fe010000.ethernet: no regulator found [ 11.382529] rk_gmac-dwmac fe010000.ethernet: clock input or output? (output). [ 11.383178] rk_gmac-dwmac fe010000.ethernet: Can not read property: tx_delay. [ 11.383815] rk_gmac-dwmac fe010000.ethernet: set tx_delay to 0x30 [ 11.384373] rk_gmac-dwmac fe010000.ethernet: Can not read property: rx_delay. [ 11.385008] rk_gmac-dwmac fe010000.ethernet: set rx_delay to 0x10 [ 11.385561] rk_gmac-dwmac fe010000.ethernet: integrated PHY? (no). [ 11.396162] rk_gmac-dwmac fe010000.ethernet: init for RGMII_ID [ 11.400201] rk_gmac-dwmac fe010000.ethernet: User ID: 0x30, Synopsys ID: 0x51 [ 11.400878] rk_gmac-dwmac fe010000.ethernet: DWMAC4/5 [ 11.401349] rk_gmac-dwmac fe010000.ethernet: DMA HW capability register suppd [ 11.402067] rk_gmac-dwmac fe010000.ethernet: RX Checksum Offload Engine suppd [ 11.402755] rk_gmac-dwmac fe010000.ethernet: TX Checksum insertion supported [ 11.403401] rk_gmac-dwmac fe010000.ethernet: Wake-Up On Lan supported [ 11.404185] rk_gmac-dwmac fe010000.ethernet: TSO supported [ 11.406883] rk_gmac-dwmac fe010000.ethernet: Enable RX Mitigation via HW Watr [ 11.407964] rk_gmac-dwmac fe010000.ethernet: Enabled RFS Flow TC (entries=10) [ 11.408624] rk_gmac-dwmac fe010000.ethernet: TSO feature enabled [ 11.411098] rk_gmac-dwmac fe010000.ethernet: Using 32/32 bits DMA host/devich [ 11.421076] rk_gmac-dwmac fe2a0000.ethernet: IRQ eth_lpi not found [ 11.422308] rk_gmac-dwmac fe2a0000.ethernet: no regulator found [ 11.422870] rk_gmac-dwmac fe2a0000.ethernet: clock input or output? (output). [ 11.423515] rk_gmac-dwmac fe2a0000.ethernet: Can not read property: tx_delay. [ 11.425161] rk_gmac-dwmac fe2a0000.ethernet: set tx_delay to 0x30 [ 11.425862] rk_gmac-dwmac fe2a0000.ethernet: Can not read property: rx_delay. [ 11.426731] rk_gmac-dwmac fe2a0000.ethernet: set rx_delay to 0x10 [ 11.427430] rk_gmac-dwmac fe2a0000.ethernet: integrated PHY? (no). [ 11.433094] rk_gmac-dwmac fe2a0000.ethernet: init for RGMII_ID [ 11.445612] rk_gmac-dwmac fe2a0000.ethernet: User ID: 0x30, Synopsys ID: 0x51 [ 11.446753] rk_gmac-dwmac fe2a0000.ethernet: DWMAC4/5 [ 11.447265] rk_gmac-dwmac fe2a0000.ethernet: DMA HW capability register suppd [ 11.447940] rk_gmac-dwmac fe2a0000.ethernet: RX Checksum Offload Engine suppd [ 11.448612] rk_gmac-dwmac fe2a0000.ethernet: TX Checksum insertion supported [ 11.449536] rk_gmac-dwmac fe2a0000.ethernet: Wake-Up On Lan supported [ 11.452947] rk_gmac-dwmac fe2a0000.ethernet: TSO supported [ 11.453468] rk_gmac-dwmac fe2a0000.ethernet: Enable RX Mitigation via HW Watr [ 11.454401] rk_gmac-dwmac fe2a0000.ethernet: Enabled RFS Flow TC (entries=10) [ 11.455054] rk_gmac-dwmac fe2a0000.ethernet: TSO feature enabled [ 11.456887] rk_gmac-dwmac fe2a0000.ethernet: Using 32/32 bits DMA host/devich [ 12.340615] rk_gmac-dwmac fe010000.ethernet eth0: Register MEM_TYPE_PAGE_POO0 [ 12.342575] rk_gmac-dwmac fe010000.ethernet eth0: no phy found [ 12.343121] rk_gmac-dwmac fe010000.ethernet eth0: __stmmac_open: Cannot atta)Quoted 92 lines
root@bpi-r2pro:~# dmesg | grep rk_gmac-dwmac [ 3.033681] rk_gmac-dwmac fe010000.ethernet: IRQ eth_lpi not found [ 3.034528] rk_gmac-dwmac fe010000.ethernet: Looking up phy-supply from devie [ 3.035243] rk_gmac-dwmac fe010000.ethernet: Looking up phy-supply property d [ 3.036170] rk_gmac-dwmac fe010000.ethernet: no regulator found [ 3.036713] rk_gmac-dwmac fe010000.ethernet: clock input or output? (output). [ 3.037361] rk_gmac-dwmac fe010000.ethernet: TX delay(0x3c). [ 3.037877] rk_gmac-dwmac fe010000.ethernet: RX delay(0x2f). [ 3.038398] rk_gmac-dwmac fe010000.ethernet: integrated PHY? (no). [ 3.044063] rk_gmac-dwmac fe010000.ethernet: init for RGMII [ 3.044896] rk_gmac-dwmac fe010000.ethernet: User ID: 0x30, Synopsys ID: 0x51 [ 3.045559] rk_gmac-dwmac fe010000.ethernet: DWMAC4/5 [ 3.046033] rk_gmac-dwmac fe010000.ethernet: DMA HW capability register suppd [ 3.046747] rk_gmac-dwmac fe010000.ethernet: RX Checksum Offload Engine suppd [ 3.047428] rk_gmac-dwmac fe010000.ethernet: TX Checksum insertion supported [ 3.048062] rk_gmac-dwmac fe010000.ethernet: Wake-Up On Lan supported [ 3.048725] rk_gmac-dwmac fe010000.ethernet: TSO supported [ 3.049229] rk_gmac-dwmac fe010000.ethernet: Enable RX Mitigation via HW Watr [ 3.049954] rk_gmac-dwmac fe010000.ethernet: Enabled RFS Flow TC (entries=10) [ 3.050628] rk_gmac-dwmac fe010000.ethernet: TSO feature enabled [ 3.051176] rk_gmac-dwmac fe010000.ethernet: Using 32/32 bits DMA host/devich [ 3.189988] rk_gmac-dwmac fe2a0000.ethernet: IRQ eth_lpi not found [ 3.190982] rk_gmac-dwmac fe2a0000.ethernet: Looking up phy-supply from devie [ 3.191715] rk_gmac-dwmac fe2a0000.ethernet: Looking up phy-supply property d [ 3.192636] rk_gmac-dwmac fe2a0000.ethernet: no regulator found [ 3.193180] rk_gmac-dwmac fe2a0000.ethernet: clock input or output? (input). [ 3.193818] rk_gmac-dwmac fe2a0000.ethernet: TX delay(0x4f). [ 3.194336] rk_gmac-dwmac fe2a0000.ethernet: RX delay(0xf). [ 3.194885] rk_gmac-dwmac fe2a0000.ethernet: integrated PHY? (no). [ 3.195499] rk_gmac-dwmac fe2a0000.ethernet: clock input from PHY [ 3.201067] rk_gmac-dwmac fe2a0000.ethernet: init for RGMII [ 3.201885] rk_gmac-dwmac fe2a0000.ethernet: User ID: 0x30, Synopsys ID: 0x51 [ 3.202575] rk_gmac-dwmac fe2a0000.ethernet: DWMAC4/5 [ 3.203052] rk_gmac-dwmac fe2a0000.ethernet: DMA HW capability register suppd [ 3.203730] rk_gmac-dwmac fe2a0000.ethernet: RX Checksum Offload Engine suppd [ 3.204405] rk_gmac-dwmac fe2a0000.ethernet: TX Checksum insertion supported [ 3.205039] rk_gmac-dwmac fe2a0000.ethernet: Wake-Up On Lan supported [ 3.205702] rk_gmac-dwmac fe2a0000.ethernet: TSO supported [ 3.206207] rk_gmac-dwmac fe2a0000.ethernet: Enable RX Mitigation via HW Watr [ 3.206969] rk_gmac-dwmac fe2a0000.ethernet: Enabled RFS Flow TC (entries=10) [ 3.207621] rk_gmac-dwmac fe2a0000.ethernet: TSO feature enabled [ 3.208167] rk_gmac-dwmac fe2a0000.ethernet: Using 32/32 bits DMA host/devich [ 80.517694] rk_gmac-dwmac fe010000.ethernet eth0: Register MEM_TYPE_PAGE_POO0 [ 80.520178] rk_gmac-dwmac fe010000.ethernet eth0: PHY [stmmac-1:00] driver [) [ 80.520230] rk_gmac-dwmac fe010000.ethernet eth0: No Safety Features supportd [ 80.520258] rk_gmac-dwmac fe010000.ethernet eth0: IEEE 1588-2008 Advanced Tid [ 80.520514] rk_gmac-dwmac fe010000.ethernet eth0: registered PTP clock [ 80.520898] rk_gmac-dwmac fe010000.ethernet eth0: configuring for phy/rgmii e [ 84.615184] rk_gmac-dwmac fe010000.ethernet eth0: Link is Up - 1Gbps/Full - x root@bpi-r2pro:~# ip a 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group defau0 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group def0 link/ether 76:95:00:96:b3:89 brd ff:ff:ff:ff:ff:ff inet 192.168.0.12/24 scope global eth0 valid_lft forever preferred_lft forever inet6 fe80::7495:ff:fe96:b389/64 scope link valid_lft forever preferred_lft forever 3: eth1: <BROADCAST,MULTICAST> mtu 1504 qdisc noop state DOWN group default qle0 link/ether 76:95:00:96:b3:88 brd ff:ff:ff:ff:ff:ff 4: sit0@NONE: <NOARP> mtu 1480 qdisc noop state DOWN group default qlen 1000 link/sit 0.0.0.0 brd 0.0.0.0 5: lan0@eth1: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc noop state DOWN group0 link/ether 76:95:00:96:b3:88 brd ff:ff:ff:ff:ff:ff 6: lan1@eth1: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc noop state DOWN group0 link/ether 76:95:00:96:b3:88 brd ff:ff:ff:ff:ff:ff 7: lan2@eth1: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc noop state DOWN group0 link/ether 76:95:00:96:b3:88 brd ff:ff:ff:ff:ff:ff 8: lan3@eth1: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc noop state DOWN group0 link/ether 76:95:00:96:b3:88 brd ff:ff:ff:ff:ff:ff root@bpi-r2pro:~# lsusb Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 008 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 007 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 005 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub root@bpi-r2pro:~# lspci 0001:00:00.0 PCI bridge: Rockchip Electronics Co., Ltd RK3568 Remote Signal Pro) 0002:00:00.0 PCI bridge: Rockchip Electronics Co., Ltd RK3568 Remote Signal Pro) root@bpi-r2pro:~# uname -a Linux bpi-r2pro 6.3.0-rc4-bpi-r2pro #1 SMP PREEMPT Mon Apr 10 13:39:18 CEST 202x root@bpi-r2pro:~#tested eth1 too...also working. so maybe "only" a evb related dts-change or between rc4 and rc6
Quoted 7 lines
Quoted 1 line
Maybe the device tree is not correct on evb...
or you miss any
Kconfigoption (regulator/power-related)else make a diff between last working version (dt + config). i see no relevant changes in dts itself between 6.2 and 6.3
regards Frank
Quoted 7 lines
Thanks!
Doug_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip
Quoted 4 lines
_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip
_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip
Hi Doug,
Quoted 6 lines · Doug Brewer
[...]
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines · Doug Brewer
Quoted 4 lines
Hi,
I tested Linux kernel 6.3-rc6 on my rk3568 evaluation board, it seems there are problems with Ethernet, PCIe and usb devices.
PCIe is addressed in a separate thread. As to USB, everything in the log seems to be normal -- at least the root hubs should show up in lsusb. Please add the output of lsusb for the sake of completeness.
Quoted 3 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
First, NICs doesn't work.
[...]
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
mdio_busstmmac-1: MDIO device at address 0 is missing.
Can you try setting CONFIG_REALTEK_PHY=m to CONFIG_REALTEK_PHY=y in your config?
Quoted 1 line
[...]
Best regards,
Michael
_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip
Quoted 6 lines · Michael Riesch
Hi Doug,
Quoted 2 lines · Doug Brewer
[...]
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line · Doug Brewer
Quoted 8 lines
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Hi,
I tested Linux kernel 6.3-rc6 on my rk3568 evaluation board, it seems there are problems with Ethernet, PCIe and usb devices.
PCIe is addressed in a separate thread. As to USB, everything in the log seems to be normal -- at least the root hubs should show up in lsusb. Please add the output of lsusb for the sake of completeness.
Sorry for the confusion. You're right, USB does work!
Quoted 5 lines
Quoted 3 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
First, NICs doesn't work.
[...]
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
mdio_busstmmac-1: MDIO device at address 0 is missing.Can you try setting
CONFIG_REALTEK_PHY=mtoCONFIG_REALTEK_PHY=yin your config?
Setting CONFIG_REALTEK_PHY=m to CONFIG_REALTEK_PHY=y, eth0 still doesn't work.
rk_gmac-dwmac fe010000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0 rk_gmac-dwmac fe010000.ethernet eth0: __stmmac_open: Cannot attach to PHY (error : -19)
Thanks,
Doug
_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip