Skip to contentSkip to conversation

Documentation: networking: add UPF (User Plane Function in 5GC) description

PATCH In review Ian Chen 2 participants 2 messages Jun 28, 2023

Subsystems (3)
lore
Share & tools
lore

Ian Chen

author
#0 lore raw

PATCH 1/1 Documentation: networking: add UPF (User Plane Function in 5GC) description

Add the content of User Plane Function (UPF), which was defined in 3GPP specifications since release 15.

---
 Documentation/networking/gtp.rst | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)
Documentation/networking/gtp.rst +5 -5
index 9a7835cc1..c02aa34c4 100644
@@ -31,12 +31,12 @@ payload, such as LLC/SNDCP/RLC/MAC.
 
 At some network element inside the cellular operator infrastructure
 (SGSN in case of GPRS/EGPRS or classic UMTS, hNodeB in case of a 3G
-femtocell, eNodeB in case of 4G/LTE), the cellular protocol stacking
+femtocell, eNodeB in case of 4G/LTE, gNobeB in case of 5G), the cellular protocol stacking
 is translated into GTP *without breaking the end-to-end tunnel*.  So
 intermediate nodes just perform some specific relay function.
 
-At some point the GTP packet ends up on the so-called GGSN (GSM/UMTS)
-or P-GW (LTE), which terminates the tunnel, decapsulates the packet
+At some point the GTP packet ends up on the so-called GGSN (GSM/UMTS),
+P-GW (LTE), or UPF (5G), which terminates the tunnel, decapsulates the packet
 and forwards it onto an external packet data network.  This can be
 public internet, but can also be any private IP network (or even
 theoretically some non-IP network like X.25).
@@ -60,7 +60,7 @@ payload, called GTP-U.  It does not implement the 'control plane',
 which is a signaling protocol used for establishment and teardown of
 GTP tunnels (GTP-C).
 
-So in order to have a working GGSN/P-GW setup, you will need a
+So in order to have a working GGSN/P-GW/UPF setup, you will need a
 userspace program that implements the GTP-C protocol and which then
 uses the netlink interface provided by the GTP-U module in the kernel
 to configure the kernel module.
@@ -162,7 +162,7 @@ Local GTP-U entity and tunnel identification
 GTP-U uses UDP for transporting PDU's. The receiving UDP port is 2152
 for GTPv1-U and 3386 for GTPv0-U.
 
-There is only one GTP-U entity (and therefore SGSN/GGSN/S-GW/PDN-GW
+There is only one GTP-U entity (and therefore SGSN/GGSN/S-GW/PDN-GW/UPF
 instance) per IP address. Tunnel Endpoint Identifier (TEID) are unique
 per GTP-U entity.
 
Signature · 1 line
2.38.1
#1 lore raw
Quoted 4 lines · Ian Chen

Add the content of User Plane Function (UPF), which was defined in 3GPP specifications since release 15.

Hi Ian,

I'm assuming this is targeted at 'net-next', as opposed to 'net', which is for fixes (I'm never sure with documentation). In any case, the target tree should be included in the subject.

Subject: [PATCH net-next v2] ...

If it is for net-next, then please repost when net-next reopens after July 10th.

Quoted 9 lines
---
 Documentation/networking/gtp.rst | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)
Documentation/networking/gtp.rst +0 -0
index 9a7835cc1..c02aa34c4 100644

Documentation/networking/gtp.rst payload, such as LLC/SNDCP/RLC/MAC. · line 36

Quoted 7 lines
Documentation/networking/gtp.rst +1 -1
@@ -31,12 +31,12 @@ payload, such as LLC/SNDCP/RLC/MAC.
 
 At some network element inside the cellular operator infrastructure
 (SGSN in case of GPRS/EGPRS or classic UMTS, hNodeB in case of a 3G
-femtocell, eNodeB in case of 4G/LTE), the cellular protocol stacking
+femtocell, eNodeB in case of 4G/LTE, gNobeB in case of 5G), the cellular protocol stacking
 is translated into GTP *without breaking the end-to-end tunnel*.  So
 intermediate nodes just perform some specific relay function.

I think it would be best to update the line-wrapping to keep lines less than 80 columns wide.

Quoted 28 lines
Documentation/networking/gtp.rst +4 -4
-At some point the GTP packet ends up on the so-called GGSN (GSM/UMTS)
-or P-GW (LTE), which terminates the tunnel, decapsulates the packet
+At some point the GTP packet ends up on the so-called GGSN (GSM/UMTS),
+P-GW (LTE), or UPF (5G), which terminates the tunnel, decapsulates the packet
 and forwards it onto an external packet data network.  This can be
 public internet, but can also be any private IP network (or even
 theoretically some non-IP network like X.25).
@@ -60,7 +60,7 @@ payload, called GTP-U.  It does not implement the 'control plane',
 which is a signaling protocol used for establishment and teardown of
 GTP tunnels (GTP-C).
 
-So in order to have a working GGSN/P-GW setup, you will need a
+So in order to have a working GGSN/P-GW/UPF setup, you will need a
 userspace program that implements the GTP-C protocol and which then
 uses the netlink interface provided by the GTP-U module in the kernel
 to configure the kernel module.
@@ -162,7 +162,7 @@ Local GTP-U entity and tunnel identification
 GTP-U uses UDP for transporting PDU's. The receiving UDP port is 2152
 for GTPv1-U and 3386 for GTPv0-U.
 
-There is only one GTP-U entity (and therefore SGSN/GGSN/S-GW/PDN-GW
+There is only one GTP-U entity (and therefore SGSN/GGSN/S-GW/PDN-GW/UPF
 instance) per IP address. Tunnel Endpoint Identifier (TEID) are unique
 per GTP-U entity.
 
Signature · 1 line
2.38.1
Signature · 1 line
pw-bot: changes-requested