dt-bindings: arm: fsl: Document Compulab IOT-GATE-iMX8
Subsystems (2)
Fabio Estevam
reviewerPATCH v4 1/2 dt-bindings: arm: fsl: Document Compulab IOT-GATE-iMX8
From: Fabio Estevam <[email protected]>
Document Compulab's IOT-GATE-iMX8 board, which is based on Compulab's UCM-iMX8M-Mini SoM.
Board URL:
https://www.compulab.com/products/iot-gateways/iot-gate-imx8-industrial-arm-iot-gateway/
---
Changes since v3:
- None
Documentation/devicetree/bindings/arm/fsl.yaml | 7 +++++++ 1 file changed, 7 insertions(+)
Documentation/devicetree/bindings/arm/fsl.yaml +7 -0
@@ -946,6 +946,13 @@ properties: - prt,prt8mm # i.MX8MM Protonic PRT8MM Board - const: fsl,imx8mm + - description: Compulab i.MX8MM UCM SoM based boards + items: + - enum: + - compulab,imx8mm-iot-gateway # i.MX8MM Compulab IoT-Gateway + - const: compulab,imx8mm-ucm-som # i.MX8MM Compulab UCM SoM + - const: fsl,imx8mm + - description: Emtop i.MX8MM based Boards items: - const: ees,imx8mm-emtop-baseboard # i.MX8MM Emtop SoM on i.MX8M Mini Baseboard V1
Signature · 1 line
2.34.1
Fabio Estevam
reviewerPATCH v4 2/2 arm64: dts: imx8mm-iot-gateway: Add initial support
From: Fabio Estevam <[email protected]>
Add the initial support for the CompuLab i.MX8MM IoT Gateway board, which is based on the Compulab's UCM-iMX8M-Mini SoM.
Board URL:
https://www.compulab.com/products/iot-gateways/iot-gate-imx8-industrial-arm-iot-gateway/
---
Changes since v3:
- Place enable-active-high right after GPIO_ACTIVE_HIGH line. (Shawn)
- Place pinctrl_usb9514 after pinctrl_pcie0. (Shawn)
- Remove unneeded okay status. (Shawn)
- Remove underscore in the node name. (Shawn)
arch/arm64/boot/dts/freescale/Makefile | 1 + .../boot/dts/freescale/imx8mm-iot-gateway.dts | 218 ++++++ .../boot/dts/freescale/imx8mm-ucm-som.dtsi | 679 ++++++++++++++++++ 3 files changed, 898 insertions(+) create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-iot-gateway.dts create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-ucm-som.dtsi
arch/arm64/boot/dts/freescale/Makefile +1 -0
@@ -114,6 +114,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-evkb.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-icore-mx8mm-ctouch2.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-icore-mx8mm-edimm2.2.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8mm-iot-gateway.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-innocomm-wb15-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-kontron-bl.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-kontron-bl-osm-s.dtb
arch/arm64/boot/dts/freescale/imx8mm-iot-gateway.dts new file +218 -0
218 lines not on this page · raw message
arch/arm64/boot/dts/freescale/imx8mm-ucm-som.dtsi new file +679 -0
679 lines not on this page · raw message
Signature · 1 line
2.34.1
Shawn Guo
AppliedQuoted 5 lines · Fabio Estevam
From: Fabio Estevam <[email protected]>
Document Compulab's IOT-GATE-iMX8 board, which is based on Compulab's UCM-iMX8M-Mini SoM.
Quoted 8 lines
Board URL:
https://www.compulab.com/products/iot-gateways/iot-gate-imx8-industrial-arm-iot-gateway/Signed-off-by Fabio Estevam <[email protected]>
Applied both, thanks!