Input: cyttsp - use devm_regulator_bulk_get_enable()
Subsystems (3)
Dmitry Torokhov
maintainerPATCH 1/1 Input: cyttsp - use devm_regulator_bulk_get_enable()
The driver does not try to power down the rails at system suspend or when touchscreen is not in use, but rather enables regulators at probe time. Power savings are achieved by requesting the controller to enter low power mode.
Switch to devm_regulator_bulk_get_enable() instead of separately requesting regulators, enabling them, and installing a custom devm-action to disable them on unbind/remove, which simplifies the code.
--- drivers/input/touchscreen/cyttsp_core.c | 38 ++++++------------------- drivers/input/touchscreen/cyttsp_core.h | 1 - 2 files changed, 8 insertions(+), 31 deletions(-)
drivers/input/touchscreen/cyttsp_core.c +8 -30
@@ -614,17 +614,14 @@ static int cyttsp_parse_properties(struct cyttsp *ts)return 0 ; } -static void cyttsp_disable_regulators (void *_ts) -{ -struct cyttsp *ts = _ts; - -regulator_bulk_disable (ARRAY_SIZE (ts->regulators), - ts->regulators); -} -struct cyttsp *cyttsp_probe (const struct cyttsp_bus_ops *bus_ops,struct device *dev,int irq,size_t xfer_buf_size) { +/* +* VCPIN is the analog voltage supply +* VDD is the digital voltage supply +*/ +static const char *const supplies[] = {"vcpin" ,"vdd" };struct cyttsp *ts;struct input_dev *input_dev;int error;
@@ -642,29 +639,10 @@ struct cyttsp *cyttsp_probe(const struct cyttsp_bus_ops *bus_ops, ts->bus_ops = bus_ops; ts->irq = irq; -/* -* VCPIN is the analog voltage supply -* VDD is the digital voltage supply -*/ - ts->regulators[0 ].supply ="vcpin" ; - ts->regulators[1 ].supply ="vdd" ; - error =devm_regulator_bulk_get (dev,ARRAY_SIZE (ts->regulators), - ts->regulators); -if (error) { -dev_err (dev,"Failed to get regulators: %d\n" , error); -return ERR_PTR (error); - } - - error =regulator_bulk_enable (ARRAY_SIZE (ts->regulators), - ts->regulators); -if (error) { -dev_err (dev,"Cannot enable regulators: %d\n" , error); -return ERR_PTR (error); - } - - error =devm_add_action_or_reset (dev, cyttsp_disable_regulators, ts); + error =devm_regulator_bulk_get_enable (dev,ARRAY_SIZE (supplies), + supplies);if (error) { -dev_err (dev,"failed to install chip disable handler\n" ); +dev_err (dev,"Failed to enable regulators: %d\n" , error);return ERR_PTR (error); }
drivers/input/touchscreen/cyttsp_core.h +0 -1
@@ -122,7 +122,6 @@ struct cyttsp {enum cyttsp_state state;bool suspended; -struct regulator_bulk_data regulators[2 ];struct gpio_desc *reset_gpio;bool use_hndshk;u8 act_dist;
Signature · 5 lines
2.46.0.rc2.264.g509ed76dc8-goog -- Dmitry
Quoted 11 lines · Dmitry Torokhov
The driver does not try to power down the rails at system suspend or when touchscreen is not in use, but rather enables regulators at probe time. Power savings are achieved by requesting the controller to enter low power mode.
Switch to
devm_regulator_bulk_get_enable()instead of separately requesting regulators, enabling them, and installing a custom devm-action to disable them on unbind/remove, which simplifies the code.Signed-off-by Dmitry Torokhov <[email protected]>
Yours,
Linus Walleij