dt-bindings: Cleanup standard unit properties
Subsystems (21)
Rob Herring
maintainerPATCH 1/1 dt-bindings: Cleanup standard unit properties
Properties with standard unit suffixes already have a type and don't need type definitions. They also default to a single entry, so 'maxItems: 1' can be dropped.
adi,ad5758 is an oddball which defined an enum of arrays. While a valid schema, it is simpler as a whole to only define scalar constraints.
--- .../devicetree/bindings/arm/cpus.yaml | 1 - .../bindings/extcon/wlf,arizona.yaml | 1 - .../bindings/hwmon/adi,ltc2947.yaml | 1 - .../bindings/hwmon/baikal,bt1-pvt.yaml | 8 ++-- .../devicetree/bindings/hwmon/ti,tmp513.yaml | 1 - .../devicetree/bindings/i2c/i2c-gpio.yaml | 2 - .../bindings/i2c/snps,designware-i2c.yaml | 3 -- .../bindings/iio/adc/maxim,max9611.yaml | 1 - .../bindings/iio/adc/st,stm32-adc.yaml | 1 - .../bindings/iio/adc/ti,palmas-gpadc.yaml | 2 - .../bindings/iio/dac/adi,ad5758.yaml | 41 ++++++++++++------- .../bindings/iio/health/maxim,max30100.yaml | 1 - .../input/touchscreen/touchscreen.yaml | 2 - .../bindings/mmc/mmc-controller.yaml | 1 - .../bindings/mmc/mmc-pwrseq-simple.yaml | 2 - .../bindings/net/ethernet-controller.yaml | 2 - .../devicetree/bindings/net/snps,dwmac.yaml | 1 - .../bindings/power/supply/battery.yaml | 3 -- .../bindings/power/supply/bq2515x.yaml | 1 - .../bindings/regulator/dlg,da9121.yaml | 1 - .../bindings/regulator/fixed-regulator.yaml | 2 - .../devicetree/bindings/rtc/rtc.yaml | 2 - .../devicetree/bindings/serial/pl011.yaml | 2 - .../devicetree/bindings/sound/sgtl5000.yaml | 2 - .../bindings/watchdog/watchdog.yaml | 1 - 25 files changed, 29 insertions(+), 56 deletions(-)
Documentation/devicetree/bindings/arm/cpus.yaml +0 -1
@@ -232,7 +232,6 @@ properties: by this cpu (see ./idle-states.yaml). capacity-dmips-mhz: - $ref: '/schemas/types.yaml#/definitions/uint32' description: u32 value representing CPU capacity (see ./cpu-capacity.txt) in DMIPS/MHz, relative to highest capacity-dmips-mhz
Documentation/devicetree/bindings/extcon/wlf,arizona.yaml +0 -1
@@ -85,7 +85,6 @@ properties: wlf,micd-timeout-ms: description: Timeout for microphone detection, specified in milliseconds. - $ref: "/schemas/types.yaml#/definitions/uint32" wlf,micd-force-micbias: description:
Documentation/devicetree/bindings/hwmon/adi,ltc2947.yaml +0 -1
@@ -49,7 +49,6 @@ properties: description: This property controls the Accumulation Dead band which allows to set the level of current below which no accumulation takes place. - $ref: /schemas/types.yaml#/definitions/uint32 maximum: 255 default: 0
Documentation/devicetree/bindings/hwmon/baikal,bt1-pvt.yaml +3 -5
@@ -73,11 +73,9 @@ properties: description: | Temperature sensor trimming factor. It can be used to manually adjust the temperature measurements within 7.130 degrees Celsius. - maxItems: 1 - items: - default: 0 - minimum: 0 - maximum: 7130 + default: 0 + minimum: 0 + maximum: 7130 additionalProperties: false
Documentation/devicetree/bindings/hwmon/ti,tmp513.yaml +0 -1
@@ -52,7 +52,6 @@ properties: ti,bus-range-microvolt: description: | This is the operating range of the bus voltage in microvolt - $ref: /schemas/types.yaml#/definitions/uint32 enum: [16000000, 32000000] default: 32000000
Documentation/devicetree/bindings/i2c/i2c-gpio.yaml +0 -2
@@ -39,11 +39,9 @@ properties: i2c-gpio,delay-us: description: delay between GPIO operations (may depend on each platform) - $ref: /schemas/types.yaml#/definitions/uint32 i2c-gpio,timeout-ms: description: timeout to get data - $ref: /schemas/types.yaml#/definitions/uint32 # Deprecated properties, do not use in new device tree sources: gpios:
Documentation/devicetree/bindings/i2c/snps,designware-i2c.yaml +0 -3
@@ -66,21 +66,18 @@ properties: default: 400000 i2c-sda-hold-time-ns: - maxItems: 1 description: | The property should contain the SDA hold time in nanoseconds. This option is only supported in hardware blocks version 1.11a or newer or on Microsemi SoCs. i2c-scl-falling-time-ns: - maxItems: 1 description: | The property should contain the SCL falling time in nanoseconds. This value is used to compute the tLOW period. default: 300 i2c-sda-falling-time-ns: - maxItems: 1 description: | The property should contain the SDA falling time in nanoseconds. This value is used to compute the tHIGH period.
Documentation/devicetree/bindings/iio/adc/maxim,max9611.yaml +0 -1
@@ -23,7 +23,6 @@ properties: maxItems: 1 shunt-resistor-micro-ohms: - $ref: /schemas/types.yaml#/definitions/uint32 description: | Value in micro Ohms of the shunt resistor connected between the RS+ and RS- inputs, across which the current is measured. Value needed to compute
Documentation/devicetree/bindings/iio/adc/st,stm32-adc.yaml +0 -1
@@ -248,7 +248,6 @@ patternProperties: Resolution (bits) to use for conversions: - can be 6, 8, 10 or 12 on stm32f4 - can be 8, 10, 12, 14 or 16 on stm32h7 and stm32mp1 - $ref: /schemas/types.yaml#/definitions/uint32 st,adc-channels: description: |
Documentation/devicetree/bindings/iio/adc/ti,palmas-gpadc.yaml +0 -2
@@ -42,7 +42,6 @@ properties: const: 1 ti,channel0-current-microamp: - $ref: /schemas/types.yaml#/definitions/uint32 description: Channel 0 current in uA. enum: - 0
@@ -51,7 +50,6 @@ properties: - 20 ti,channel3-current-microamp: - $ref: /schemas/types.yaml#/definitions/uint32 description: Channel 3 current in uA. enum: - 0
Documentation/devicetree/bindings/iio/dac/adi,ad5758.yaml +26 -15
57 lines not on this page · raw message
Documentation/devicetree/bindings/iio/health/maxim,max30100.yaml +0 -1
@@ -21,7 +21,6 @@ properties: description: Connected to ADC_RDY pin. maxim,led-current-microamp: - $ref: /schemas/types.yaml#/definitions/uint32-array minItems: 2 maxItems: 2 description: |
Documentation/devicetree/bindings/input/touchscreen/touchscreen.yaml +0 -2
@@ -70,11 +70,9 @@ properties: touchscreen-x-mm: description: horizontal length in mm of the touchscreen - $ref: /schemas/types.yaml#/definitions/uint32 touchscreen-y-mm: description: vertical length in mm of the touchscreen - $ref: /schemas/types.yaml#/definitions/uint32 dependencies: touchscreen-size-x: [ touchscreen-size-y ]
Documentation/devicetree/bindings/mmc/mmc-controller.yaml +0 -1
@@ -261,7 +261,6 @@ properties: waiting for I/O signalling and card power supply to be stable, regardless of whether pwrseq-simple is used. Default to 10ms if no available. - $ref: /schemas/types.yaml#/definitions/uint32 default: 10 supports-cqe:
Documentation/devicetree/bindings/mmc/mmc-pwrseq-simple.yaml +0 -2
@@ -41,13 +41,11 @@ properties: description: Delay in ms after powering the card and de-asserting the reset-gpios (if any). - $ref: /schemas/types.yaml#/definitions/uint32 power-off-delay-us: description: Delay in us after asserting the reset-gpios (if any) during power off of the card. - $ref: /schemas/types.yaml#/definitions/uint32 required: - compatible
Documentation/devicetree/bindings/net/ethernet-controller.yaml +0 -2
@@ -122,7 +122,6 @@ properties: such as flow control thresholds. rx-internal-delay-ps: - $ref: /schemas/types.yaml#/definitions/uint32 description: | RGMII Receive Clock Delay defined in pico seconds. This is used for controllers that have configurable RX internal delays.
@@ -140,7 +139,6 @@ properties: is used for components that can have configurable fifo sizes. tx-internal-delay-ps: - $ref: /schemas/types.yaml#/definitions/uint32 description: | RGMII Transmit Clock Delay defined in pico seconds. This is used for controllers that have configurable TX internal delays.
Documentation/devicetree/bindings/net/snps,dwmac.yaml +0 -1
@@ -208,7 +208,6 @@ properties: Triplet of delays. The 1st cell is reset pre-delay in micro seconds. The 2nd cell is reset pulse in micro seconds. The 3rd cell is reset post-delay in micro seconds. - $ref: /schemas/types.yaml#/definitions/uint32-array minItems: 3 maxItems: 3
Documentation/devicetree/bindings/power/supply/battery.yaml +0 -3
@@ -83,21 +83,18 @@ properties: for each of the battery capacity lookup table. operating-range-celsius: - $ref: /schemas/types.yaml#/definitions/uint32-array description: operating temperature range of a battery items: - description: minimum temperature at which battery can operate - description: maximum temperature at which battery can operate ambient-celsius: - $ref: /schemas/types.yaml#/definitions/uint32-array description: safe range of ambient temperature items: - description: alert when ambient temperature is lower than this value - description: alert when ambient temperature is higher than this value alert-celsius: - $ref: /schemas/types.yaml#/definitions/uint32-array description: safe range of battery temperature items: - description: alert when battery temperature is lower than this value
Documentation/devicetree/bindings/power/supply/bq2515x.yaml +0 -1
@@ -50,7 +50,6 @@ properties: maxItems: 1 input-current-limit-microamp: - $ref: /schemas/types.yaml#/definitions/uint32 description: Maximum input current in micro Amps. minimum: 50000 maximum: 500000
Documentation/devicetree/bindings/regulator/dlg,da9121.yaml +0 -1
@@ -62,7 +62,6 @@ properties: description: IRQ line information. dlg,irq-polling-delay-passive-ms: - $ref: "/schemas/types.yaml#/definitions/uint32" minimum: 1000 maximum: 10000 description: |
Documentation/devicetree/bindings/regulator/fixed-regulator.yaml +0 -2
@@ -72,11 +72,9 @@ properties: startup-delay-us: description: startup time in microseconds - $ref: /schemas/types.yaml#/definitions/uint32 off-on-delay-us: description: off delay time in microseconds - $ref: /schemas/types.yaml#/definitions/uint32 enable-active-high: description:
Documentation/devicetree/bindings/rtc/rtc.yaml +0 -2
@@ -27,7 +27,6 @@ properties: 1: chargeable quartz-load-femtofarads: - $ref: /schemas/types.yaml#/definitions/uint32 description: The capacitive load of the quartz(x-tal), expressed in femto Farad (fF). The default value shall be listed (if optional),
@@ -47,7 +46,6 @@ properties: deprecated: true trickle-resistor-ohms: - $ref: /schemas/types.yaml#/definitions/uint32 description: Selected resistor for trickle charger. Should be given if trickle charger should be enabled.
Documentation/devicetree/bindings/serial/pl011.yaml +0 -2
@@ -88,14 +88,12 @@ properties: description: Rate at which poll occurs when auto-poll is set. default 100ms. - $ref: /schemas/types.yaml#/definitions/uint32 default: 100 poll-timeout-ms: description: Poll timeout when auto-poll is set, default 3000ms. - $ref: /schemas/types.yaml#/definitions/uint32 default: 3000 required:
Documentation/devicetree/bindings/sound/sgtl5000.yaml +0 -2
@@ -41,14 +41,12 @@ properties: values of 2k, 4k or 8k. If set to 0 it will be off. If this node is not mentioned or if the value is unknown, then micbias resistor is set to 4k. - $ref: "/schemas/types.yaml#/definitions/uint32" enum: [ 0, 2, 4, 8 ] micbias-voltage-m-volts: description: The bias voltage to be used in mVolts. The voltage can take values from 1.25V to 3V by 250mV steps. If this node is not mentioned or the value is unknown, then the value is set to 1.25V. - $ref: "/schemas/types.yaml#/definitions/uint32" enum: [ 1250, 1500, 1750, 2000, 2250, 2500, 2750, 3000 ] lrclk-strength:
Documentation/devicetree/bindings/watchdog/watchdog.yaml +0 -1
@@ -19,7 +19,6 @@ properties: pattern: "^watchdog(@.*|-[0-9a-f])?$" timeout-sec: - $ref: /schemas/types.yaml#/definitions/uint32 description: Contains the watchdog timeout in seconds.
Signature · 1 line
2.27.0
Quoted 7 lines · Rob Herring
Properties with standard unit suffixes already have a type and don't need type definitions. They also default to a single entry, so 'maxItems: 1' can be dropped.
adi,ad5758 is an oddball which defined an enum of arrays. While a valid schema, it is simpler as a whole to only define scalar constraints.
Quoted 16 lines
Cc Jean Delvare <[email protected]>Cc Guenter Roeck <[email protected]>Cc Jonathan Cameron <[email protected]>Cc Lars-Peter Clausen <[email protected]>Cc Alexandre Torgue <[email protected]>Cc Dmitry Torokhov <[email protected]>Cc Ulf Hansson <[email protected]>Cc "David S. Miller" <[email protected]>Cc Jakub Kicinski <[email protected]>Cc Sebastian Reichel <[email protected]>Cc Mark Brown <[email protected]>Cc Alexandre Belloni <[email protected]>Cc Greg Kroah-Hartman <[email protected]>Cc Serge Semin <[email protected]>Cc Wolfram Sang <[email protected]>
Quoted 484 lines
Signed-off-by Rob Herring <[email protected]>--- .../devicetree/bindings/arm/cpus.yaml | 1 - .../bindings/extcon/wlf,arizona.yaml | 1 - .../bindings/hwmon/adi,ltc2947.yaml | 1 - .../bindings/hwmon/baikal,bt1-pvt.yaml | 8 ++-- .../devicetree/bindings/hwmon/ti,tmp513.yaml | 1 - .../devicetree/bindings/i2c/i2c-gpio.yaml | 2 - .../bindings/i2c/snps,designware-i2c.yaml | 3 -- .../bindings/iio/adc/maxim,max9611.yaml | 1 - .../bindings/iio/adc/st,stm32-adc.yaml | 1 - .../bindings/iio/adc/ti,palmas-gpadc.yaml | 2 - .../bindings/iio/dac/adi,ad5758.yaml | 41 ++++++++++++------- .../bindings/iio/health/maxim,max30100.yaml | 1 - .../input/touchscreen/touchscreen.yaml | 2 - .../bindings/mmc/mmc-controller.yaml | 1 - .../bindings/mmc/mmc-pwrseq-simple.yaml | 2 - .../bindings/net/ethernet-controller.yaml | 2 - .../devicetree/bindings/net/snps,dwmac.yaml | 1 - .../bindings/power/supply/battery.yaml | 3 -- .../bindings/power/supply/bq2515x.yaml | 1 - .../bindings/regulator/dlg,da9121.yaml | 1 - .../bindings/regulator/fixed-regulator.yaml | 2 - .../devicetree/bindings/rtc/rtc.yaml | 2 - .../devicetree/bindings/serial/pl011.yaml | 2 - .../devicetree/bindings/sound/sgtl5000.yaml | 2 - .../bindings/watchdog/watchdog.yaml | 1 - 25 files changed, 29 insertions(+), 56 deletions(-)Documentation/devicetree/bindings/arm/cpus.yaml +0
-1@@ -232,7 +232,6 @@ properties: by this cpu (see ./idle-states.yaml). capacity-dmips-mhz: - $ref: '/schemas/types.yaml#/definitions/uint32' description: u32 value representing CPU capacity (see ./cpu-capacity.txt) in DMIPS/MHz, relative to highest capacity-dmips-mhzDocumentation/devicetree/bindings/extcon/wlf,arizona.yaml +0
-1@@ -85,7 +85,6 @@ properties: wlf,micd-timeout-ms: description: Timeout for microphone detection, specified in milliseconds. - $ref: "/schemas/types.yaml#/definitions/uint32" wlf,micd-force-micbias: description:Documentation/devicetree/bindings/hwmon/adi,ltc2947.yaml +0
-1@@ -49,7 +49,6 @@ properties: description: This property controls the Accumulation Dead band which allows to set the level of current below which no accumulation takes place. - $ref: /schemas/types.yaml#/definitions/uint32 maximum: 255 default: 0Documentation/devicetree/bindings/hwmon/baikal,bt1-pvt.yaml +3
-5@@ -73,11 +73,9 @@ properties: description: | Temperature sensor trimming factor. It can be used to manually adjust the temperature measurements within 7.130 degrees Celsius. - maxItems: 1 - items: - default: 0 - minimum: 0 - maximum: 7130 + default: 0 + minimum: 0 + maximum: 7130 additionalProperties: falseDocumentation/devicetree/bindings/hwmon/ti,tmp513.yaml +0
-1@@ -52,7 +52,6 @@ properties: ti,bus-range-microvolt: description: | This is the operating range of the bus voltage in microvolt - $ref: /schemas/types.yaml#/definitions/uint32 enum: [16000000, 32000000] default: 32000000Documentation/devicetree/bindings/i2c/i2c-gpio.yaml +0
-2@@ -39,11 +39,9 @@ properties: i2c-gpio,delay-us: description: delay between GPIO operations (may depend on each platform) - $ref: /schemas/types.yaml#/definitions/uint32 i2c-gpio,timeout-ms: description: timeout to get data - $ref: /schemas/types.yaml#/definitions/uint32 # Deprecated properties, do not use in new device tree sources: gpios:Documentation/devicetree/bindings/i2c/snps,designware-i2c.yaml +0
-3@@ -66,21 +66,18 @@ properties: default: 400000 i2c-sda-hold-time-ns: - maxItems: 1 description: | The property should contain the SDA hold time in nanoseconds. This option is only supported in hardware blocks version 1.11a or newer or on Microsemi SoCs. i2c-scl-falling-time-ns: - maxItems: 1 description: | The property should contain the SCL falling time in nanoseconds. This value is used to compute the tLOW period. default: 300 i2c-sda-falling-time-ns: - maxItems: 1 description: | The property should contain the SDA falling time in nanoseconds. This value is used to compute the tHIGH period.Documentation/devicetree/bindings/iio/adc/maxim,max9611.yaml +0
-1@@ -23,7 +23,6 @@ properties: maxItems: 1 shunt-resistor-micro-ohms: - $ref: /schemas/types.yaml#/definitions/uint32 description: | Value in micro Ohms of the shunt resistor connected between the RS+ and RS- inputs, across which the current is measured. Value needed to computeDocumentation/devicetree/bindings/iio/adc/st,stm32-adc.yaml +0
-1@@ -248,7 +248,6 @@ patternProperties: Resolution (bits) to use for conversions: - can be 6, 8, 10 or 12 on stm32f4 - can be 8, 10, 12, 14 or 16 on stm32h7 and stm32mp1 - $ref: /schemas/types.yaml#/definitions/uint32 st,adc-channels: description: |Documentation/devicetree/bindings/iio/adc/ti,palmas-gpadc.yaml +0
-2@@ -42,7 +42,6 @@ properties: const: 1 ti,channel0-current-microamp: - $ref: /schemas/types.yaml#/definitions/uint32 description: Channel 0 current in uA. enum: - 0@@ -51,7 +50,6 @@ properties: - 20 ti,channel3-current-microamp: - $ref: /schemas/types.yaml#/definitions/uint32 description: Channel 3 current in uA. enum: - 0Documentation/devicetree/bindings/iio/dac/adi,ad5758.yaml +26
-15@@ -46,31 +46,42 @@ properties: two properties must be present: adi,range-microvolt: - $ref: /schemas/types.yaml#/definitions/int32-array description: | Voltage output range specified as <minimum, maximum> - enum: - - [[0, 5000000]] - - [[0, 10000000]] - - [[-5000000, 5000000]] - - [[-10000000, 10000000]] + oneOf: + - items: + - const: 0 + - enum: [5000000, 10000000] + - items: + - const: -5000000 + - const: 5000000 + - items: + - const: -10000000 + - const: 10000000 adi,range-microamp: - $ref: /schemas/types.yaml#/definitions/int32-array description: | Current output range specified as <minimum, maximum> - enum: - - [[0, 20000]] - - [[0, 24000]] - - [[4, 24000]] - - [[-20000, 20000]] - - [[-24000, 24000]] - - [[-1000, 22000]] + oneOf: + - items: + - const: 0 + - enum: [20000, 24000] + - items: + - const: 4 + - const: 24000 + - items: + - const: -20000 + - const: 20000 + - items: + - const: -24000 + - const: 24000 + - items: + - const: -1000 + - const: 22000 reset-gpios: true adi,dc-dc-ilim-microamp: - $ref: /schemas/types.yaml#/definitions/uint32 enum: [150000, 200000, 250000, 300000, 350000, 400000] description: | The dc-to-dc converter current limit.Documentation/devicetree/bindings/iio/health/maxim,max30100.yaml +0
-1@@ -21,7 +21,6 @@ properties: description: Connected to ADC_RDY pin. maxim,led-current-microamp: - $ref: /schemas/types.yaml#/definitions/uint32-array minItems: 2 maxItems: 2 description: |Documentation/devicetree/bindings/input/touchscreen/touchscreen.yaml +0
-2@@ -70,11 +70,9 @@ properties: touchscreen-x-mm: description: horizontal length in mm of the touchscreen - $ref: /schemas/types.yaml#/definitions/uint32 touchscreen-y-mm: description: vertical length in mm of the touchscreen - $ref: /schemas/types.yaml#/definitions/uint32 dependencies: touchscreen-size-x: [ touchscreen-size-y ]Documentation/devicetree/bindings/mmc/mmc-controller.yaml +0
-1@@ -261,7 +261,6 @@ properties: waiting for I/O signalling and card power supply to be stable, regardless of whether pwrseq-simple is used. Default to 10ms if no available. - $ref: /schemas/types.yaml#/definitions/uint32 default: 10 supports-cqe:Documentation/devicetree/bindings/mmc/mmc-pwrseq-simple.yaml +0
-2@@ -41,13 +41,11 @@ properties: description: Delay in ms after powering the card and de-asserting the reset-gpios (if any). - $ref: /schemas/types.yaml#/definitions/uint32 power-off-delay-us: description: Delay in us after asserting the reset-gpios (if any) during power off of the card. - $ref: /schemas/types.yaml#/definitions/uint32 required: - compatibleDocumentation/devicetree/bindings/net/ethernet-controller.yaml +0
-2@@ -122,7 +122,6 @@ properties: such as flow control thresholds. rx-internal-delay-ps: - $ref: /schemas/types.yaml#/definitions/uint32 description: | RGMII Receive Clock Delay defined in pico seconds. This is used for controllers that have configurable RX internal delays.@@ -140,7 +139,6 @@ properties: is used for components that can have configurable fifo sizes. tx-internal-delay-ps: - $ref: /schemas/types.yaml#/definitions/uint32 description: | RGMII Transmit Clock Delay defined in pico seconds. This is used for controllers that have configurable TX internal delays.Documentation/devicetree/bindings/net/snps,dwmac.yaml +0
-1@@ -208,7 +208,6 @@ properties: Triplet of delays. The 1st cell is reset pre-delay in micro seconds. The 2nd cell is reset pulse in micro seconds. The 3rd cell is reset post-delay in micro seconds. - $ref: /schemas/types.yaml#/definitions/uint32-array minItems: 3 maxItems: 3Documentation/devicetree/bindings/power/supply/battery.yaml +0
-3@@ -83,21 +83,18 @@ properties: for each of the battery capacity lookup table. operating-range-celsius: - $ref: /schemas/types.yaml#/definitions/uint32-array description: operating temperature range of a battery items: - description: minimum temperature at which battery can operate - description: maximum temperature at which battery can operate ambient-celsius: - $ref: /schemas/types.yaml#/definitions/uint32-array description: safe range of ambient temperature items: - description: alert when ambient temperature is lower than this value - description: alert when ambient temperature is higher than this value alert-celsius: - $ref: /schemas/types.yaml#/definitions/uint32-array description: safe range of battery temperature items: - description: alert when battery temperature is lower than this valueDocumentation/devicetree/bindings/power/supply/bq2515x.yaml +0
-1@@ -50,7 +50,6 @@ properties: maxItems: 1 input-current-limit-microamp: - $ref: /schemas/types.yaml#/definitions/uint32 description: Maximum input current in micro Amps. minimum: 50000 maximum: 500000Documentation/devicetree/bindings/regulator/dlg,da9121.yaml +0
-1@@ -62,7 +62,6 @@ properties: description: IRQ line information. dlg,irq-polling-delay-passive-ms: - $ref: "/schemas/types.yaml#/definitions/uint32" minimum: 1000 maximum: 10000 description: |Documentation/devicetree/bindings/regulator/fixed-regulator.yaml +0
-2@@ -72,11 +72,9 @@ properties: startup-delay-us: description: startup time in microseconds - $ref: /schemas/types.yaml#/definitions/uint32 off-on-delay-us: description: off delay time in microseconds - $ref: /schemas/types.yaml#/definitions/uint32 enable-active-high: description:Documentation/devicetree/bindings/rtc/rtc.yaml +0
-2@@ -27,7 +27,6 @@ properties: 1: chargeable quartz-load-femtofarads: - $ref: /schemas/types.yaml#/definitions/uint32 description: The capacitive load of the quartz(x-tal), expressed in femto Farad (fF). The default value shall be listed (if optional),@@ -47,7 +46,6 @@ properties: deprecated: true trickle-resistor-ohms: - $ref: /schemas/types.yaml#/definitions/uint32 description: Selected resistor for trickle charger. Should be given if trickle charger should be enabled.Documentation/devicetree/bindings/serial/pl011.yaml +0
-2@@ -88,14 +88,12 @@ properties: description: Rate at which poll occurs when auto-poll is set. default 100ms. - $ref: /schemas/types.yaml#/definitions/uint32 default: 100 poll-timeout-ms: description: Poll timeout when auto-poll is set, default 3000ms. - $ref: /schemas/types.yaml#/definitions/uint32 default: 3000 required:Documentation/devicetree/bindings/sound/sgtl5000.yaml +0
-2@@ -41,14 +41,12 @@ properties: values of 2k, 4k or 8k. If set to 0 it will be off. If this node is not mentioned or if the value is unknown, then micbias resistor is set to 4k. - $ref: "/schemas/types.yaml#/definitions/uint32" enum: [ 0, 2, 4, 8 ] micbias-voltage-m-volts: description: The bias voltage to be used in mVolts. The voltage can take values from 1.25V to 3V by 250mV steps. If this node is not mentioned or the value is unknown, then the value is set to 1.25V. - $ref: "/schemas/types.yaml#/definitions/uint32" enum: [ 1250, 1500, 1750, 2000, 2250, 2500, 2750, 3000 ] lrclk-strength:Documentation/devicetree/bindings/watchdog/watchdog.yaml +0
-1@@ -19,7 +19,6 @@ properties: pattern: "^watchdog(@.*|-[0-9a-f])?$" timeout-sec: - $ref: /schemas/types.yaml#/definitions/uint32 description: Contains the watchdog timeout in seconds.Signature · 1 line
2.27.0
Wolfram Sang
Acked-byQuoted 7 lines · Guenter Roeck
Quoted 6 lines · Rob Herring
Properties with standard unit suffixes already have a type and don't need type definitions. They also default to a single entry, so 'maxItems: 1' can be dropped.
adi,ad5758 is an oddball which defined an enum of arrays. While a valid schema, it is simpler as a whole to only define scalar constraints.
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Quoted 3 lines · Rob Herring
Properties with standard unit suffixes already have a type and don't need type definitions. They also default to a single entry, so 'maxItems: 1' can be dropped.
Quoted 27 lines · Rob Herring
Properties with standard unit suffixes already have a type and don't need type definitions. They also default to a single entry, so 'maxItems: 1' can be dropped.
adi,ad5758 is an oddball which defined an enum of arrays. While a valid schema, it is simpler as a whole to only define scalar constraints.
Cc Jean Delvare <[email protected]>Cc Guenter Roeck <[email protected]>Cc Jonathan Cameron <[email protected]>Cc Lars-Peter Clausen <[email protected]>Cc Alexandre Torgue <[email protected]>Cc Dmitry Torokhov <[email protected]>Cc Ulf Hansson <[email protected]>Cc "David S. Miller" <[email protected]>Cc Jakub Kicinski <[email protected]>Cc Sebastian Reichel <[email protected]>Cc Mark Brown <[email protected]>Cc Alexandre Belloni <[email protected]>Cc Greg Kroah-Hartman <[email protected]>Cc Serge Semin <[email protected]>Cc Wolfram Sang <[email protected]>
Quoted 8 lines
Quoted 472 lines
--- .../devicetree/bindings/arm/cpus.yaml | 1 - .../bindings/extcon/wlf,arizona.yaml | 1 - .../bindings/hwmon/adi,ltc2947.yaml | 1 - .../bindings/hwmon/baikal,bt1-pvt.yaml | 8 ++-- .../devicetree/bindings/hwmon/ti,tmp513.yaml | 1 - .../devicetree/bindings/i2c/i2c-gpio.yaml | 2 - .../bindings/i2c/snps,designware-i2c.yaml | 3 -- .../bindings/iio/adc/maxim,max9611.yaml | 1 - .../bindings/iio/adc/st,stm32-adc.yaml | 1 - .../bindings/iio/adc/ti,palmas-gpadc.yaml | 2 - .../bindings/iio/dac/adi,ad5758.yaml | 41 ++++++++++++------- .../bindings/iio/health/maxim,max30100.yaml | 1 - .../input/touchscreen/touchscreen.yaml | 2 - .../bindings/mmc/mmc-controller.yaml | 1 - .../bindings/mmc/mmc-pwrseq-simple.yaml | 2 - .../bindings/net/ethernet-controller.yaml | 2 - .../devicetree/bindings/net/snps,dwmac.yaml | 1 - .../bindings/power/supply/battery.yaml | 3 -- .../bindings/power/supply/bq2515x.yaml | 1 - .../bindings/regulator/dlg,da9121.yaml | 1 - .../bindings/regulator/fixed-regulator.yaml | 2 - .../devicetree/bindings/rtc/rtc.yaml | 2 - .../devicetree/bindings/serial/pl011.yaml | 2 - .../devicetree/bindings/sound/sgtl5000.yaml | 2 - .../bindings/watchdog/watchdog.yaml | 1 - 25 files changed, 29 insertions(+), 56 deletions(-)Documentation/devicetree/bindings/arm/cpus.yaml +0
-1@@ -232,7 +232,6 @@ properties: by this cpu (see ./idle-states.yaml). capacity-dmips-mhz: - $ref: '/schemas/types.yaml#/definitions/uint32' description: u32 value representing CPU capacity (see ./cpu-capacity.txt) in DMIPS/MHz, relative to highest capacity-dmips-mhzDocumentation/devicetree/bindings/extcon/wlf,arizona.yaml +0
-1@@ -85,7 +85,6 @@ properties: wlf,micd-timeout-ms: description: Timeout for microphone detection, specified in milliseconds. - $ref: "/schemas/types.yaml#/definitions/uint32" wlf,micd-force-micbias: description:Documentation/devicetree/bindings/hwmon/adi,ltc2947.yaml +0
-1@@ -49,7 +49,6 @@ properties: description: This property controls the Accumulation Dead band which allows to set the level of current below which no accumulation takes place. - $ref: /schemas/types.yaml#/definitions/uint32 maximum: 255 default: 0Documentation/devicetree/bindings/hwmon/baikal,bt1-pvt.yaml +3
-5@@ -73,11 +73,9 @@ properties: description: | Temperature sensor trimming factor. It can be used to manually adjust the temperature measurements within 7.130 degrees Celsius. - maxItems: 1 - items: - default: 0 - minimum: 0 - maximum: 7130 + default: 0 + minimum: 0 + maximum: 7130 additionalProperties: falseDocumentation/devicetree/bindings/hwmon/ti,tmp513.yaml +0
-1@@ -52,7 +52,6 @@ properties: ti,bus-range-microvolt: description: | This is the operating range of the bus voltage in microvolt - $ref: /schemas/types.yaml#/definitions/uint32 enum: [16000000, 32000000] default: 32000000Documentation/devicetree/bindings/i2c/i2c-gpio.yaml +0
-2@@ -39,11 +39,9 @@ properties: i2c-gpio,delay-us: description: delay between GPIO operations (may depend on each platform) - $ref: /schemas/types.yaml#/definitions/uint32 i2c-gpio,timeout-ms: description: timeout to get data - $ref: /schemas/types.yaml#/definitions/uint32 # Deprecated properties, do not use in new device tree sources: gpios:Documentation/devicetree/bindings/i2c/snps,designware-i2c.yaml +0
-3@@ -66,21 +66,18 @@ properties: default: 400000 i2c-sda-hold-time-ns: - maxItems: 1 description: | The property should contain the SDA hold time in nanoseconds. This option is only supported in hardware blocks version 1.11a or newer or on Microsemi SoCs. i2c-scl-falling-time-ns: - maxItems: 1 description: | The property should contain the SCL falling time in nanoseconds. This value is used to compute the tLOW period. default: 300 i2c-sda-falling-time-ns: - maxItems: 1 description: | The property should contain the SDA falling time in nanoseconds. This value is used to compute the tHIGH period.Documentation/devicetree/bindings/iio/adc/maxim,max9611.yaml +0
-1@@ -23,7 +23,6 @@ properties: maxItems: 1 shunt-resistor-micro-ohms: - $ref: /schemas/types.yaml#/definitions/uint32 description: | Value in micro Ohms of the shunt resistor connected between the RS+ and RS- inputs, across which the current is measured. Value needed to computeDocumentation/devicetree/bindings/iio/adc/st,stm32-adc.yaml +0
-1@@ -248,7 +248,6 @@ patternProperties: Resolution (bits) to use for conversions: - can be 6, 8, 10 or 12 on stm32f4 - can be 8, 10, 12, 14 or 16 on stm32h7 and stm32mp1 - $ref: /schemas/types.yaml#/definitions/uint32 st,adc-channels: description: |Documentation/devicetree/bindings/iio/adc/ti,palmas-gpadc.yaml +0
-2@@ -42,7 +42,6 @@ properties: const: 1 ti,channel0-current-microamp: - $ref: /schemas/types.yaml#/definitions/uint32 description: Channel 0 current in uA. enum: - 0@@ -51,7 +50,6 @@ properties: - 20 ti,channel3-current-microamp: - $ref: /schemas/types.yaml#/definitions/uint32 description: Channel 3 current in uA. enum: - 0Documentation/devicetree/bindings/iio/dac/adi,ad5758.yaml +26
-15@@ -46,31 +46,42 @@ properties: two properties must be present: adi,range-microvolt: - $ref: /schemas/types.yaml#/definitions/int32-array description: | Voltage output range specified as <minimum, maximum> - enum: - - [[0, 5000000]] - - [[0, 10000000]] - - [[-5000000, 5000000]] - - [[-10000000, 10000000]] + oneOf: + - items: + - const: 0 + - enum: [5000000, 10000000] + - items: + - const: -5000000 + - const: 5000000 + - items: + - const: -10000000 + - const: 10000000 adi,range-microamp: - $ref: /schemas/types.yaml#/definitions/int32-array description: | Current output range specified as <minimum, maximum> - enum: - - [[0, 20000]] - - [[0, 24000]] - - [[4, 24000]] - - [[-20000, 20000]] - - [[-24000, 24000]] - - [[-1000, 22000]] + oneOf: + - items: + - const: 0 + - enum: [20000, 24000] + - items: + - const: 4 + - const: 24000 + - items: + - const: -20000 + - const: 20000 + - items: + - const: -24000 + - const: 24000 + - items: + - const: -1000 + - const: 22000 reset-gpios: true adi,dc-dc-ilim-microamp: - $ref: /schemas/types.yaml#/definitions/uint32 enum: [150000, 200000, 250000, 300000, 350000, 400000] description: | The dc-to-dc converter current limit.Documentation/devicetree/bindings/iio/health/maxim,max30100.yaml +0
-1@@ -21,7 +21,6 @@ properties: description: Connected to ADC_RDY pin. maxim,led-current-microamp: - $ref: /schemas/types.yaml#/definitions/uint32-array minItems: 2 maxItems: 2 description: |Documentation/devicetree/bindings/input/touchscreen/touchscreen.yaml +0
-2@@ -70,11 +70,9 @@ properties: touchscreen-x-mm: description: horizontal length in mm of the touchscreen - $ref: /schemas/types.yaml#/definitions/uint32 touchscreen-y-mm: description: vertical length in mm of the touchscreen - $ref: /schemas/types.yaml#/definitions/uint32 dependencies: touchscreen-size-x: [ touchscreen-size-y ]Documentation/devicetree/bindings/mmc/mmc-controller.yaml +0
-1@@ -261,7 +261,6 @@ properties: waiting for I/O signalling and card power supply to be stable, regardless of whether pwrseq-simple is used. Default to 10ms if no available. - $ref: /schemas/types.yaml#/definitions/uint32 default: 10 supports-cqe:Documentation/devicetree/bindings/mmc/mmc-pwrseq-simple.yaml +0
-2@@ -41,13 +41,11 @@ properties: description: Delay in ms after powering the card and de-asserting the reset-gpios (if any). - $ref: /schemas/types.yaml#/definitions/uint32 power-off-delay-us: description: Delay in us after asserting the reset-gpios (if any) during power off of the card. - $ref: /schemas/types.yaml#/definitions/uint32 required: - compatibleDocumentation/devicetree/bindings/net/ethernet-controller.yaml +0
-2@@ -122,7 +122,6 @@ properties: such as flow control thresholds. rx-internal-delay-ps: - $ref: /schemas/types.yaml#/definitions/uint32 description: | RGMII Receive Clock Delay defined in pico seconds. This is used for controllers that have configurable RX internal delays.@@ -140,7 +139,6 @@ properties: is used for components that can have configurable fifo sizes. tx-internal-delay-ps: - $ref: /schemas/types.yaml#/definitions/uint32 description: | RGMII Transmit Clock Delay defined in pico seconds. This is used for controllers that have configurable TX internal delays.Documentation/devicetree/bindings/net/snps,dwmac.yaml +0
-1@@ -208,7 +208,6 @@ properties: Triplet of delays. The 1st cell is reset pre-delay in micro seconds. The 2nd cell is reset pulse in micro seconds. The 3rd cell is reset post-delay in micro seconds. - $ref: /schemas/types.yaml#/definitions/uint32-array minItems: 3 maxItems: 3Documentation/devicetree/bindings/power/supply/battery.yaml +0
-3@@ -83,21 +83,18 @@ properties: for each of the battery capacity lookup table. operating-range-celsius: - $ref: /schemas/types.yaml#/definitions/uint32-array description: operating temperature range of a battery items: - description: minimum temperature at which battery can operate - description: maximum temperature at which battery can operate ambient-celsius: - $ref: /schemas/types.yaml#/definitions/uint32-array description: safe range of ambient temperature items: - description: alert when ambient temperature is lower than this value - description: alert when ambient temperature is higher than this value alert-celsius: - $ref: /schemas/types.yaml#/definitions/uint32-array description: safe range of battery temperature items: - description: alert when battery temperature is lower than this valueDocumentation/devicetree/bindings/power/supply/bq2515x.yaml +0
-1@@ -50,7 +50,6 @@ properties: maxItems: 1 input-current-limit-microamp: - $ref: /schemas/types.yaml#/definitions/uint32 description: Maximum input current in micro Amps. minimum: 50000 maximum: 500000Documentation/devicetree/bindings/regulator/dlg,da9121.yaml +0
-1@@ -62,7 +62,6 @@ properties: description: IRQ line information. dlg,irq-polling-delay-passive-ms: - $ref: "/schemas/types.yaml#/definitions/uint32" minimum: 1000 maximum: 10000 description: |Documentation/devicetree/bindings/regulator/fixed-regulator.yaml +0
-2@@ -72,11 +72,9 @@ properties: startup-delay-us: description: startup time in microseconds - $ref: /schemas/types.yaml#/definitions/uint32 off-on-delay-us: description: off delay time in microseconds - $ref: /schemas/types.yaml#/definitions/uint32 enable-active-high: description:Documentation/devicetree/bindings/rtc/rtc.yaml +0
-2@@ -27,7 +27,6 @@ properties: 1: chargeable quartz-load-femtofarads: - $ref: /schemas/types.yaml#/definitions/uint32 description: The capacitive load of the quartz(x-tal), expressed in femto Farad (fF). The default value shall be listed (if optional),@@ -47,7 +46,6 @@ properties: deprecated: true trickle-resistor-ohms: - $ref: /schemas/types.yaml#/definitions/uint32 description: Selected resistor for trickle charger. Should be given if trickle charger should be enabled.Documentation/devicetree/bindings/serial/pl011.yaml +0
-2@@ -88,14 +88,12 @@ properties: description: Rate at which poll occurs when auto-poll is set. default 100ms. - $ref: /schemas/types.yaml#/definitions/uint32 default: 100 poll-timeout-ms: description: Poll timeout when auto-poll is set, default 3000ms. - $ref: /schemas/types.yaml#/definitions/uint32 default: 3000 required:Documentation/devicetree/bindings/sound/sgtl5000.yaml +0
-2@@ -41,14 +41,12 @@ properties: values of 2k, 4k or 8k. If set to 0 it will be off. If this node is not mentioned or if the value is unknown, then micbias resistor is set to 4k. - $ref: "/schemas/types.yaml#/definitions/uint32" enum: [ 0, 2, 4, 8 ] micbias-voltage-m-volts: description: The bias voltage to be used in mVolts. The voltage can take values from 1.25V to 3V by 250mV steps. If this node is not mentioned or the value is unknown, then the value is set to 1.25V. - $ref: "/schemas/types.yaml#/definitions/uint32" enum: [ 1250, 1500, 1750, 2000, 2250, 2500, 2750, 3000 ] lrclk-strength:Documentation/devicetree/bindings/watchdog/watchdog.yaml +0
-1@@ -19,7 +19,6 @@ properties: pattern: "^watchdog(@.*|-[0-9a-f])?$" timeout-sec: - $ref: /schemas/types.yaml#/definitions/uint32 description: Contains the watchdog timeout in seconds.Signature · 1 line
2.27.0
Signature · 3 lines
Alexandre Belloni, Bootlin Embedded Linux and Kernel engineering https://bootlin.com
Quoted 27 lines · Rob Herring
Properties with standard unit suffixes already have a type and don't need type definitions. They also default to a single entry, so 'maxItems: 1' can be dropped.
adi,ad5758 is an oddball which defined an enum of arrays. While a valid schema, it is simpler as a whole to only define scalar constraints.
Cc Jean Delvare <[email protected]>Cc Guenter Roeck <[email protected]>Cc Jonathan Cameron <[email protected]>Cc Lars-Peter Clausen <[email protected]>Cc Alexandre Torgue <[email protected]>Cc Dmitry Torokhov <[email protected]>Cc Ulf Hansson <[email protected]>Cc "David S. Miller" <[email protected]>Cc Jakub Kicinski <[email protected]>Cc Sebastian Reichel <[email protected]>Cc Mark Brown <[email protected]>Cc Alexandre Belloni <[email protected]>Cc Greg Kroah-Hartman <[email protected]>Cc Serge Semin <[email protected]>Cc Wolfram Sang <[email protected]>
Quoted 8 lines
Hi,
Quoted 54 lines · Rob Herring
Properties with standard unit suffixes already have a type and don't need type definitions. They also default to a single entry, so 'maxItems: 1' can be dropped.
adi,ad5758 is an oddball which defined an enum of arrays. While a valid schema, it is simpler as a whole to only define scalar constraints.
Cc Jean Delvare <[email protected]>Cc Guenter Roeck <[email protected]>Cc Jonathan Cameron <[email protected]>Cc Lars-Peter Clausen <[email protected]>Cc Alexandre Torgue <[email protected]>Cc Dmitry Torokhov <[email protected]>Cc Ulf Hansson <[email protected]>Cc "David S. Miller" <[email protected]>Cc Jakub Kicinski <[email protected]>Cc Sebastian Reichel <[email protected]>Cc Mark Brown <[email protected]>Cc Alexandre Belloni <[email protected]>Cc Greg Kroah-Hartman <[email protected]>Cc Serge Semin <[email protected]>Cc Wolfram Sang <[email protected]>Signed-off-by Rob Herring <[email protected]>--- .../devicetree/bindings/arm/cpus.yaml | 1 - .../bindings/extcon/wlf,arizona.yaml | 1 - .../bindings/hwmon/adi,ltc2947.yaml | 1 - .../bindings/hwmon/baikal,bt1-pvt.yaml | 8 ++-- .../devicetree/bindings/hwmon/ti,tmp513.yaml | 1 - .../devicetree/bindings/i2c/i2c-gpio.yaml | 2 - .../bindings/i2c/snps,designware-i2c.yaml | 3 -- .../bindings/iio/adc/maxim,max9611.yaml | 1 - .../bindings/iio/adc/st,stm32-adc.yaml | 1 - .../bindings/iio/adc/ti,palmas-gpadc.yaml | 2 - .../bindings/iio/dac/adi,ad5758.yaml | 41 ++++++++++++------- .../bindings/iio/health/maxim,max30100.yaml | 1 - .../input/touchscreen/touchscreen.yaml | 2 - .../bindings/mmc/mmc-controller.yaml | 1 - .../bindings/mmc/mmc-pwrseq-simple.yaml | 2 - .../bindings/net/ethernet-controller.yaml | 2 - .../devicetree/bindings/net/snps,dwmac.yaml | 1 - .../bindings/power/supply/battery.yaml | 3 --
Quoted 8 lines
.../bindings/power/supply/bq2515x.yaml | 1 - .../bindings/regulator/dlg,da9121.yaml | 1 - .../bindings/regulator/fixed-regulator.yaml | 2 - .../devicetree/bindings/rtc/rtc.yaml | 2 - .../devicetree/bindings/serial/pl011.yaml | 2 - .../devicetree/bindings/sound/sgtl5000.yaml | 2 - .../bindings/watchdog/watchdog.yaml | 1 - 25 files changed, 29 insertions(+), 56 deletions(-)
-- Sebastian
Quoted 445 lines
Documentation/devicetree/bindings/arm/cpus.yaml +0
-1@@ -232,7 +232,6 @@ properties: by this cpu (see ./idle-states.yaml). capacity-dmips-mhz: - $ref: '/schemas/types.yaml#/definitions/uint32' description: u32 value representing CPU capacity (see ./cpu-capacity.txt) in DMIPS/MHz, relative to highest capacity-dmips-mhzDocumentation/devicetree/bindings/extcon/wlf,arizona.yaml +0
-1@@ -85,7 +85,6 @@ properties: wlf,micd-timeout-ms: description: Timeout for microphone detection, specified in milliseconds. - $ref: "/schemas/types.yaml#/definitions/uint32" wlf,micd-force-micbias: description:Documentation/devicetree/bindings/hwmon/adi,ltc2947.yaml +0
-1@@ -49,7 +49,6 @@ properties: description: This property controls the Accumulation Dead band which allows to set the level of current below which no accumulation takes place. - $ref: /schemas/types.yaml#/definitions/uint32 maximum: 255 default: 0Documentation/devicetree/bindings/hwmon/baikal,bt1-pvt.yaml +3
-5@@ -73,11 +73,9 @@ properties: description: | Temperature sensor trimming factor. It can be used to manually adjust the temperature measurements within 7.130 degrees Celsius. - maxItems: 1 - items: - default: 0 - minimum: 0 - maximum: 7130 + default: 0 + minimum: 0 + maximum: 7130 additionalProperties: falseDocumentation/devicetree/bindings/hwmon/ti,tmp513.yaml +0
-1@@ -52,7 +52,6 @@ properties: ti,bus-range-microvolt: description: | This is the operating range of the bus voltage in microvolt - $ref: /schemas/types.yaml#/definitions/uint32 enum: [16000000, 32000000] default: 32000000Documentation/devicetree/bindings/i2c/i2c-gpio.yaml +0
-2@@ -39,11 +39,9 @@ properties: i2c-gpio,delay-us: description: delay between GPIO operations (may depend on each platform) - $ref: /schemas/types.yaml#/definitions/uint32 i2c-gpio,timeout-ms: description: timeout to get data - $ref: /schemas/types.yaml#/definitions/uint32 # Deprecated properties, do not use in new device tree sources: gpios:Documentation/devicetree/bindings/i2c/snps,designware-i2c.yaml +0
-3@@ -66,21 +66,18 @@ properties: default: 400000 i2c-sda-hold-time-ns: - maxItems: 1 description: | The property should contain the SDA hold time in nanoseconds. This option is only supported in hardware blocks version 1.11a or newer or on Microsemi SoCs. i2c-scl-falling-time-ns: - maxItems: 1 description: | The property should contain the SCL falling time in nanoseconds. This value is used to compute the tLOW period. default: 300 i2c-sda-falling-time-ns: - maxItems: 1 description: | The property should contain the SDA falling time in nanoseconds. This value is used to compute the tHIGH period.Documentation/devicetree/bindings/iio/adc/maxim,max9611.yaml +0
-1@@ -23,7 +23,6 @@ properties: maxItems: 1 shunt-resistor-micro-ohms: - $ref: /schemas/types.yaml#/definitions/uint32 description: | Value in micro Ohms of the shunt resistor connected between the RS+ and RS- inputs, across which the current is measured. Value needed to computeDocumentation/devicetree/bindings/iio/adc/st,stm32-adc.yaml +0
-1@@ -248,7 +248,6 @@ patternProperties: Resolution (bits) to use for conversions: - can be 6, 8, 10 or 12 on stm32f4 - can be 8, 10, 12, 14 or 16 on stm32h7 and stm32mp1 - $ref: /schemas/types.yaml#/definitions/uint32 st,adc-channels: description: |Documentation/devicetree/bindings/iio/adc/ti,palmas-gpadc.yaml +0
-2@@ -42,7 +42,6 @@ properties: const: 1 ti,channel0-current-microamp: - $ref: /schemas/types.yaml#/definitions/uint32 description: Channel 0 current in uA. enum: - 0@@ -51,7 +50,6 @@ properties: - 20 ti,channel3-current-microamp: - $ref: /schemas/types.yaml#/definitions/uint32 description: Channel 3 current in uA. enum: - 0Documentation/devicetree/bindings/iio/dac/adi,ad5758.yaml +26
-15@@ -46,31 +46,42 @@ properties: two properties must be present: adi,range-microvolt: - $ref: /schemas/types.yaml#/definitions/int32-array description: | Voltage output range specified as <minimum, maximum> - enum: - - [[0, 5000000]] - - [[0, 10000000]] - - [[-5000000, 5000000]] - - [[-10000000, 10000000]] + oneOf: + - items: + - const: 0 + - enum: [5000000, 10000000] + - items: + - const: -5000000 + - const: 5000000 + - items: + - const: -10000000 + - const: 10000000 adi,range-microamp: - $ref: /schemas/types.yaml#/definitions/int32-array description: | Current output range specified as <minimum, maximum> - enum: - - [[0, 20000]] - - [[0, 24000]] - - [[4, 24000]] - - [[-20000, 20000]] - - [[-24000, 24000]] - - [[-1000, 22000]] + oneOf: + - items: + - const: 0 + - enum: [20000, 24000] + - items: + - const: 4 + - const: 24000 + - items: + - const: -20000 + - const: 20000 + - items: + - const: -24000 + - const: 24000 + - items: + - const: -1000 + - const: 22000 reset-gpios: true adi,dc-dc-ilim-microamp: - $ref: /schemas/types.yaml#/definitions/uint32 enum: [150000, 200000, 250000, 300000, 350000, 400000] description: | The dc-to-dc converter current limit.Documentation/devicetree/bindings/iio/health/maxim,max30100.yaml +0
-1@@ -21,7 +21,6 @@ properties: description: Connected to ADC_RDY pin. maxim,led-current-microamp: - $ref: /schemas/types.yaml#/definitions/uint32-array minItems: 2 maxItems: 2 description: |Documentation/devicetree/bindings/input/touchscreen/touchscreen.yaml +0
-2@@ -70,11 +70,9 @@ properties: touchscreen-x-mm: description: horizontal length in mm of the touchscreen - $ref: /schemas/types.yaml#/definitions/uint32 touchscreen-y-mm: description: vertical length in mm of the touchscreen - $ref: /schemas/types.yaml#/definitions/uint32 dependencies: touchscreen-size-x: [ touchscreen-size-y ]Documentation/devicetree/bindings/mmc/mmc-controller.yaml +0
-1@@ -261,7 +261,6 @@ properties: waiting for I/O signalling and card power supply to be stable, regardless of whether pwrseq-simple is used. Default to 10ms if no available. - $ref: /schemas/types.yaml#/definitions/uint32 default: 10 supports-cqe:Documentation/devicetree/bindings/mmc/mmc-pwrseq-simple.yaml +0
-2@@ -41,13 +41,11 @@ properties: description: Delay in ms after powering the card and de-asserting the reset-gpios (if any). - $ref: /schemas/types.yaml#/definitions/uint32 power-off-delay-us: description: Delay in us after asserting the reset-gpios (if any) during power off of the card. - $ref: /schemas/types.yaml#/definitions/uint32 required: - compatibleDocumentation/devicetree/bindings/net/ethernet-controller.yaml +0
-2@@ -122,7 +122,6 @@ properties: such as flow control thresholds. rx-internal-delay-ps: - $ref: /schemas/types.yaml#/definitions/uint32 description: | RGMII Receive Clock Delay defined in pico seconds. This is used for controllers that have configurable RX internal delays.@@ -140,7 +139,6 @@ properties: is used for components that can have configurable fifo sizes. tx-internal-delay-ps: - $ref: /schemas/types.yaml#/definitions/uint32 description: | RGMII Transmit Clock Delay defined in pico seconds. This is used for controllers that have configurable TX internal delays.Documentation/devicetree/bindings/net/snps,dwmac.yaml +0
-1@@ -208,7 +208,6 @@ properties: Triplet of delays. The 1st cell is reset pre-delay in micro seconds. The 2nd cell is reset pulse in micro seconds. The 3rd cell is reset post-delay in micro seconds. - $ref: /schemas/types.yaml#/definitions/uint32-array minItems: 3 maxItems: 3Documentation/devicetree/bindings/power/supply/battery.yaml +0
-3@@ -83,21 +83,18 @@ properties: for each of the battery capacity lookup table. operating-range-celsius: - $ref: /schemas/types.yaml#/definitions/uint32-array description: operating temperature range of a battery items: - description: minimum temperature at which battery can operate - description: maximum temperature at which battery can operate ambient-celsius: - $ref: /schemas/types.yaml#/definitions/uint32-array description: safe range of ambient temperature items: - description: alert when ambient temperature is lower than this value - description: alert when ambient temperature is higher than this value alert-celsius: - $ref: /schemas/types.yaml#/definitions/uint32-array description: safe range of battery temperature items: - description: alert when battery temperature is lower than this valueDocumentation/devicetree/bindings/power/supply/bq2515x.yaml +0
-1@@ -50,7 +50,6 @@ properties: maxItems: 1 input-current-limit-microamp: - $ref: /schemas/types.yaml#/definitions/uint32 description: Maximum input current in micro Amps. minimum: 50000 maximum: 500000Documentation/devicetree/bindings/regulator/dlg,da9121.yaml +0
-1@@ -62,7 +62,6 @@ properties: description: IRQ line information. dlg,irq-polling-delay-passive-ms: - $ref: "/schemas/types.yaml#/definitions/uint32" minimum: 1000 maximum: 10000 description: |Documentation/devicetree/bindings/regulator/fixed-regulator.yaml +0
-2@@ -72,11 +72,9 @@ properties: startup-delay-us: description: startup time in microseconds - $ref: /schemas/types.yaml#/definitions/uint32 off-on-delay-us: description: off delay time in microseconds - $ref: /schemas/types.yaml#/definitions/uint32 enable-active-high: description:Documentation/devicetree/bindings/rtc/rtc.yaml +0
-2@@ -27,7 +27,6 @@ properties: 1: chargeable quartz-load-femtofarads: - $ref: /schemas/types.yaml#/definitions/uint32 description: The capacitive load of the quartz(x-tal), expressed in femto Farad (fF). The default value shall be listed (if optional),@@ -47,7 +46,6 @@ properties: deprecated: true trickle-resistor-ohms: - $ref: /schemas/types.yaml#/definitions/uint32 description: Selected resistor for trickle charger. Should be given if trickle charger should be enabled.Documentation/devicetree/bindings/serial/pl011.yaml +0
-2@@ -88,14 +88,12 @@ properties: description: Rate at which poll occurs when auto-poll is set. default 100ms. - $ref: /schemas/types.yaml#/definitions/uint32 default: 100 poll-timeout-ms: description: Poll timeout when auto-poll is set, default 3000ms. - $ref: /schemas/types.yaml#/definitions/uint32 default: 3000 required:Documentation/devicetree/bindings/sound/sgtl5000.yaml +0
-2@@ -41,14 +41,12 @@ properties: values of 2k, 4k or 8k. If set to 0 it will be off. If this node is not mentioned or if the value is unknown, then micbias resistor is set to 4k. - $ref: "/schemas/types.yaml#/definitions/uint32" enum: [ 0, 2, 4, 8 ] micbias-voltage-m-volts: description: The bias voltage to be used in mVolts. The voltage can take values from 1.25V to 3V by 250mV steps. If this node is not mentioned or the value is unknown, then the value is set to 1.25V. - $ref: "/schemas/types.yaml#/definitions/uint32" enum: [ 1250, 1500, 1750, 2000, 2250, 2500, 2750, 3000 ] lrclk-strength:Documentation/devicetree/bindings/watchdog/watchdog.yaml +0
-1@@ -19,7 +19,6 @@ properties: pattern: "^watchdog(@.*|-[0-9a-f])?$" timeout-sec: - $ref: /schemas/types.yaml#/definitions/uint32 description: Contains the watchdog timeout in seconds.Signature · 1 line
2.27.0
Quoted 6 lines · On Thu, 28 Jan 2021 13:45:15 -0600 Rob Herring <[email protected]> wrote:
Properties with standard unit suffixes already have a type and don't need type definitions. They also default to a single entry, so 'maxItems: 1' can be dropped.
adi,ad5758 is an oddball which defined an enum of arrays. While a valid schema, it is simpler as a whole to only define scalar constraints.
New form for ad5758 looks fine, if perhaps not as immediately readable. The rest are fine.
Thanks
Quoted 491 lines
Cc Jean Delvare <[email protected]>Cc Guenter Roeck <[email protected]>Cc Jonathan Cameron <[email protected]>Cc Lars-Peter Clausen <[email protected]>Cc Alexandre Torgue <[email protected]>Cc Dmitry Torokhov <[email protected]>Cc Ulf Hansson <[email protected]>Cc "David S. Miller" <[email protected]>Cc Jakub Kicinski <[email protected]>Cc Sebastian Reichel <[email protected]>Cc Mark Brown <[email protected]>Cc Alexandre Belloni <[email protected]>Cc Greg Kroah-Hartman <[email protected]>Cc Serge Semin <[email protected]>Cc Wolfram Sang <[email protected]>Signed-off-by Rob Herring <[email protected]>--- .../devicetree/bindings/arm/cpus.yaml | 1 - .../bindings/extcon/wlf,arizona.yaml | 1 - .../bindings/hwmon/adi,ltc2947.yaml | 1 - .../bindings/hwmon/baikal,bt1-pvt.yaml | 8 ++-- .../devicetree/bindings/hwmon/ti,tmp513.yaml | 1 - .../devicetree/bindings/i2c/i2c-gpio.yaml | 2 - .../bindings/i2c/snps,designware-i2c.yaml | 3 -- .../bindings/iio/adc/maxim,max9611.yaml | 1 - .../bindings/iio/adc/st,stm32-adc.yaml | 1 - .../bindings/iio/adc/ti,palmas-gpadc.yaml | 2 - .../bindings/iio/dac/adi,ad5758.yaml | 41 ++++++++++++------- .../bindings/iio/health/maxim,max30100.yaml | 1 - .../input/touchscreen/touchscreen.yaml | 2 - .../bindings/mmc/mmc-controller.yaml | 1 - .../bindings/mmc/mmc-pwrseq-simple.yaml | 2 - .../bindings/net/ethernet-controller.yaml | 2 - .../devicetree/bindings/net/snps,dwmac.yaml | 1 - .../bindings/power/supply/battery.yaml | 3 -- .../bindings/power/supply/bq2515x.yaml | 1 - .../bindings/regulator/dlg,da9121.yaml | 1 - .../bindings/regulator/fixed-regulator.yaml | 2 - .../devicetree/bindings/rtc/rtc.yaml | 2 - .../devicetree/bindings/serial/pl011.yaml | 2 - .../devicetree/bindings/sound/sgtl5000.yaml | 2 - .../bindings/watchdog/watchdog.yaml | 1 - 25 files changed, 29 insertions(+), 56 deletions(-)Documentation/devicetree/bindings/arm/cpus.yaml +0
-1@@ -232,7 +232,6 @@ properties: by this cpu (see ./idle-states.yaml). capacity-dmips-mhz: - $ref: '/schemas/types.yaml#/definitions/uint32' description: u32 value representing CPU capacity (see ./cpu-capacity.txt) in DMIPS/MHz, relative to highest capacity-dmips-mhzDocumentation/devicetree/bindings/extcon/wlf,arizona.yaml +0
-1@@ -85,7 +85,6 @@ properties: wlf,micd-timeout-ms: description: Timeout for microphone detection, specified in milliseconds. - $ref: "/schemas/types.yaml#/definitions/uint32" wlf,micd-force-micbias: description:Documentation/devicetree/bindings/hwmon/adi,ltc2947.yaml +0
-1@@ -49,7 +49,6 @@ properties: description: This property controls the Accumulation Dead band which allows to set the level of current below which no accumulation takes place. - $ref: /schemas/types.yaml#/definitions/uint32 maximum: 255 default: 0Documentation/devicetree/bindings/hwmon/baikal,bt1-pvt.yaml +3
-5@@ -73,11 +73,9 @@ properties: description: | Temperature sensor trimming factor. It can be used to manually adjust the temperature measurements within 7.130 degrees Celsius. - maxItems: 1 - items: - default: 0 - minimum: 0 - maximum: 7130 + default: 0 + minimum: 0 + maximum: 7130 additionalProperties: falseDocumentation/devicetree/bindings/hwmon/ti,tmp513.yaml +0
-1@@ -52,7 +52,6 @@ properties: ti,bus-range-microvolt: description: | This is the operating range of the bus voltage in microvolt - $ref: /schemas/types.yaml#/definitions/uint32 enum: [16000000, 32000000] default: 32000000Documentation/devicetree/bindings/i2c/i2c-gpio.yaml +0
-2@@ -39,11 +39,9 @@ properties: i2c-gpio,delay-us: description: delay between GPIO operations (may depend on each platform) - $ref: /schemas/types.yaml#/definitions/uint32 i2c-gpio,timeout-ms: description: timeout to get data - $ref: /schemas/types.yaml#/definitions/uint32 # Deprecated properties, do not use in new device tree sources: gpios:Documentation/devicetree/bindings/i2c/snps,designware-i2c.yaml +0
-3@@ -66,21 +66,18 @@ properties: default: 400000 i2c-sda-hold-time-ns: - maxItems: 1 description: | The property should contain the SDA hold time in nanoseconds. This option is only supported in hardware blocks version 1.11a or newer or on Microsemi SoCs. i2c-scl-falling-time-ns: - maxItems: 1 description: | The property should contain the SCL falling time in nanoseconds. This value is used to compute the tLOW period. default: 300 i2c-sda-falling-time-ns: - maxItems: 1 description: | The property should contain the SDA falling time in nanoseconds. This value is used to compute the tHIGH period.Documentation/devicetree/bindings/iio/adc/maxim,max9611.yaml +0
-1@@ -23,7 +23,6 @@ properties: maxItems: 1 shunt-resistor-micro-ohms: - $ref: /schemas/types.yaml#/definitions/uint32 description: | Value in micro Ohms of the shunt resistor connected between the RS+ and RS- inputs, across which the current is measured. Value needed to computeDocumentation/devicetree/bindings/iio/adc/st,stm32-adc.yaml +0
-1@@ -248,7 +248,6 @@ patternProperties: Resolution (bits) to use for conversions: - can be 6, 8, 10 or 12 on stm32f4 - can be 8, 10, 12, 14 or 16 on stm32h7 and stm32mp1 - $ref: /schemas/types.yaml#/definitions/uint32 st,adc-channels: description: |Documentation/devicetree/bindings/iio/adc/ti,palmas-gpadc.yaml +0
-2@@ -42,7 +42,6 @@ properties: const: 1 ti,channel0-current-microamp: - $ref: /schemas/types.yaml#/definitions/uint32 description: Channel 0 current in uA. enum: - 0@@ -51,7 +50,6 @@ properties: - 20 ti,channel3-current-microamp: - $ref: /schemas/types.yaml#/definitions/uint32 description: Channel 3 current in uA. enum: - 0Documentation/devicetree/bindings/iio/dac/adi,ad5758.yaml +26
-15@@ -46,31 +46,42 @@ properties: two properties must be present: adi,range-microvolt: - $ref: /schemas/types.yaml#/definitions/int32-array description: | Voltage output range specified as <minimum, maximum> - enum: - - [[0, 5000000]] - - [[0, 10000000]] - - [[-5000000, 5000000]] - - [[-10000000, 10000000]] + oneOf: + - items: + - const: 0 + - enum: [5000000, 10000000] + - items: + - const: -5000000 + - const: 5000000 + - items: + - const: -10000000 + - const: 10000000 adi,range-microamp: - $ref: /schemas/types.yaml#/definitions/int32-array description: | Current output range specified as <minimum, maximum> - enum: - - [[0, 20000]] - - [[0, 24000]] - - [[4, 24000]] - - [[-20000, 20000]] - - [[-24000, 24000]] - - [[-1000, 22000]] + oneOf: + - items: + - const: 0 + - enum: [20000, 24000] + - items: + - const: 4 + - const: 24000 + - items: + - const: -20000 + - const: 20000 + - items: + - const: -24000 + - const: 24000 + - items: + - const: -1000 + - const: 22000 reset-gpios: true adi,dc-dc-ilim-microamp: - $ref: /schemas/types.yaml#/definitions/uint32 enum: [150000, 200000, 250000, 300000, 350000, 400000] description: | The dc-to-dc converter current limit.Documentation/devicetree/bindings/iio/health/maxim,max30100.yaml +0
-1@@ -21,7 +21,6 @@ properties: description: Connected to ADC_RDY pin. maxim,led-current-microamp: - $ref: /schemas/types.yaml#/definitions/uint32-array minItems: 2 maxItems: 2 description: |Documentation/devicetree/bindings/input/touchscreen/touchscreen.yaml +0
-2@@ -70,11 +70,9 @@ properties: touchscreen-x-mm: description: horizontal length in mm of the touchscreen - $ref: /schemas/types.yaml#/definitions/uint32 touchscreen-y-mm: description: vertical length in mm of the touchscreen - $ref: /schemas/types.yaml#/definitions/uint32 dependencies: touchscreen-size-x: [ touchscreen-size-y ]Documentation/devicetree/bindings/mmc/mmc-controller.yaml +0
-1@@ -261,7 +261,6 @@ properties: waiting for I/O signalling and card power supply to be stable, regardless of whether pwrseq-simple is used. Default to 10ms if no available. - $ref: /schemas/types.yaml#/definitions/uint32 default: 10 supports-cqe:Documentation/devicetree/bindings/mmc/mmc-pwrseq-simple.yaml +0
-2@@ -41,13 +41,11 @@ properties: description: Delay in ms after powering the card and de-asserting the reset-gpios (if any). - $ref: /schemas/types.yaml#/definitions/uint32 power-off-delay-us: description: Delay in us after asserting the reset-gpios (if any) during power off of the card. - $ref: /schemas/types.yaml#/definitions/uint32 required: - compatibleDocumentation/devicetree/bindings/net/ethernet-controller.yaml +0
-2@@ -122,7 +122,6 @@ properties: such as flow control thresholds. rx-internal-delay-ps: - $ref: /schemas/types.yaml#/definitions/uint32 description: | RGMII Receive Clock Delay defined in pico seconds. This is used for controllers that have configurable RX internal delays.@@ -140,7 +139,6 @@ properties: is used for components that can have configurable fifo sizes. tx-internal-delay-ps: - $ref: /schemas/types.yaml#/definitions/uint32 description: | RGMII Transmit Clock Delay defined in pico seconds. This is used for controllers that have configurable TX internal delays.Documentation/devicetree/bindings/net/snps,dwmac.yaml +0
-1@@ -208,7 +208,6 @@ properties: Triplet of delays. The 1st cell is reset pre-delay in micro seconds. The 2nd cell is reset pulse in micro seconds. The 3rd cell is reset post-delay in micro seconds. - $ref: /schemas/types.yaml#/definitions/uint32-array minItems: 3 maxItems: 3Documentation/devicetree/bindings/power/supply/battery.yaml +0
-3@@ -83,21 +83,18 @@ properties: for each of the battery capacity lookup table. operating-range-celsius: - $ref: /schemas/types.yaml#/definitions/uint32-array description: operating temperature range of a battery items: - description: minimum temperature at which battery can operate - description: maximum temperature at which battery can operate ambient-celsius: - $ref: /schemas/types.yaml#/definitions/uint32-array description: safe range of ambient temperature items: - description: alert when ambient temperature is lower than this value - description: alert when ambient temperature is higher than this value alert-celsius: - $ref: /schemas/types.yaml#/definitions/uint32-array description: safe range of battery temperature items: - description: alert when battery temperature is lower than this valueDocumentation/devicetree/bindings/power/supply/bq2515x.yaml +0
-1@@ -50,7 +50,6 @@ properties: maxItems: 1 input-current-limit-microamp: - $ref: /schemas/types.yaml#/definitions/uint32 description: Maximum input current in micro Amps. minimum: 50000 maximum: 500000Documentation/devicetree/bindings/regulator/dlg,da9121.yaml +0
-1@@ -62,7 +62,6 @@ properties: description: IRQ line information. dlg,irq-polling-delay-passive-ms: - $ref: "/schemas/types.yaml#/definitions/uint32" minimum: 1000 maximum: 10000 description: |Documentation/devicetree/bindings/regulator/fixed-regulator.yaml +0
-2@@ -72,11 +72,9 @@ properties: startup-delay-us: description: startup time in microseconds - $ref: /schemas/types.yaml#/definitions/uint32 off-on-delay-us: description: off delay time in microseconds - $ref: /schemas/types.yaml#/definitions/uint32 enable-active-high: description:Documentation/devicetree/bindings/rtc/rtc.yaml +0
-2@@ -27,7 +27,6 @@ properties: 1: chargeable quartz-load-femtofarads: - $ref: /schemas/types.yaml#/definitions/uint32 description: The capacitive load of the quartz(x-tal), expressed in femto Farad (fF). The default value shall be listed (if optional),@@ -47,7 +46,6 @@ properties: deprecated: true trickle-resistor-ohms: - $ref: /schemas/types.yaml#/definitions/uint32 description: Selected resistor for trickle charger. Should be given if trickle charger should be enabled.Documentation/devicetree/bindings/serial/pl011.yaml +0
-2@@ -88,14 +88,12 @@ properties: description: Rate at which poll occurs when auto-poll is set. default 100ms. - $ref: /schemas/types.yaml#/definitions/uint32 default: 100 poll-timeout-ms: description: Poll timeout when auto-poll is set, default 3000ms. - $ref: /schemas/types.yaml#/definitions/uint32 default: 3000 required:Documentation/devicetree/bindings/sound/sgtl5000.yaml +0
-2@@ -41,14 +41,12 @@ properties: values of 2k, 4k or 8k. If set to 0 it will be off. If this node is not mentioned or if the value is unknown, then micbias resistor is set to 4k. - $ref: "/schemas/types.yaml#/definitions/uint32" enum: [ 0, 2, 4, 8 ] micbias-voltage-m-volts: description: The bias voltage to be used in mVolts. The voltage can take values from 1.25V to 3V by 250mV steps. If this node is not mentioned or the value is unknown, then the value is set to 1.25V. - $ref: "/schemas/types.yaml#/definitions/uint32" enum: [ 1250, 1500, 1750, 2000, 2250, 2500, 2750, 3000 ] lrclk-strength:Documentation/devicetree/bindings/watchdog/watchdog.yaml +0
-0
Documentation/devicetree/bindings/watchdog/watchdog.yaml properties: · line 24
Quoted 7 lines
Documentation/devicetree/bindings/watchdog/watchdog.yaml +0
-1@@ -19,7 +19,6 @@ properties: pattern: "^watchdog(@.*|-[0-9a-f])?$" timeout-sec: - $ref: /schemas/types.yaml#/definitions/uint32 description: Contains the watchdog timeout in seconds.
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Quoted 54 lines · Rob Herring
Properties with standard unit suffixes already have a type and don't need type definitions. They also default to a single entry, so 'maxItems: 1' can be dropped.
adi,ad5758 is an oddball which defined an enum of arrays. While a valid schema, it is simpler as a whole to only define scalar constraints.
Cc Jean Delvare <[email protected]>Cc Guenter Roeck <[email protected]>Cc Jonathan Cameron <[email protected]>Cc Lars-Peter Clausen <[email protected]>Cc Alexandre Torgue <[email protected]>Cc Dmitry Torokhov <[email protected]>Cc Ulf Hansson <[email protected]>Cc "David S. Miller" <[email protected]>Cc Jakub Kicinski <[email protected]>Cc Sebastian Reichel <[email protected]>Cc Mark Brown <[email protected]>Cc Alexandre Belloni <[email protected]>Cc Greg Kroah-Hartman <[email protected]>Cc Serge Semin <[email protected]>Cc Wolfram Sang <[email protected]>Signed-off-by Rob Herring <[email protected]>--- .../devicetree/bindings/arm/cpus.yaml | 1 - .../bindings/extcon/wlf,arizona.yaml | 1 - .../bindings/hwmon/adi,ltc2947.yaml | 1 - .../bindings/hwmon/baikal,bt1-pvt.yaml | 8 ++-- .../devicetree/bindings/hwmon/ti,tmp513.yaml | 1 - .../devicetree/bindings/i2c/i2c-gpio.yaml | 2 - .../bindings/i2c/snps,designware-i2c.yaml | 3 -- .../bindings/iio/adc/maxim,max9611.yaml | 1 - .../bindings/iio/adc/st,stm32-adc.yaml | 1 - .../bindings/iio/adc/ti,palmas-gpadc.yaml | 2 - .../bindings/iio/dac/adi,ad5758.yaml | 41 ++++++++++++------- .../bindings/iio/health/maxim,max30100.yaml | 1 - .../input/touchscreen/touchscreen.yaml | 2 - .../bindings/mmc/mmc-controller.yaml | 1 - .../bindings/mmc/mmc-pwrseq-simple.yaml | 2 - .../bindings/net/ethernet-controller.yaml | 2 - .../devicetree/bindings/net/snps,dwmac.yaml | 1 - .../bindings/power/supply/battery.yaml | 3 --
Quoted 8 lines
.../bindings/power/supply/bq2515x.yaml | 1 - .../bindings/regulator/dlg,da9121.yaml | 1 - .../bindings/regulator/fixed-regulator.yaml | 2 - .../devicetree/bindings/rtc/rtc.yaml | 2 - .../devicetree/bindings/serial/pl011.yaml | 2 - .../devicetree/bindings/sound/sgtl5000.yaml | 2 - .../bindings/watchdog/watchdog.yaml | 1 - 25 files changed, 29 insertions(+), 56 deletions(-)
For stm32:
Quoted 443 lines
Documentation/devicetree/bindings/arm/cpus.yaml +0
-1@@ -232,7 +232,6 @@ properties: by this cpu (see ./idle-states.yaml). capacity-dmips-mhz: - $ref: '/schemas/types.yaml#/definitions/uint32' description: u32 value representing CPU capacity (see ./cpu-capacity.txt) in DMIPS/MHz, relative to highest capacity-dmips-mhzDocumentation/devicetree/bindings/extcon/wlf,arizona.yaml +0
-1@@ -85,7 +85,6 @@ properties: wlf,micd-timeout-ms: description: Timeout for microphone detection, specified in milliseconds. - $ref: "/schemas/types.yaml#/definitions/uint32" wlf,micd-force-micbias: description:Documentation/devicetree/bindings/hwmon/adi,ltc2947.yaml +0
-1@@ -49,7 +49,6 @@ properties: description: This property controls the Accumulation Dead band which allows to set the level of current below which no accumulation takes place. - $ref: /schemas/types.yaml#/definitions/uint32 maximum: 255 default: 0Documentation/devicetree/bindings/hwmon/baikal,bt1-pvt.yaml +3
-5@@ -73,11 +73,9 @@ properties: description: | Temperature sensor trimming factor. It can be used to manually adjust the temperature measurements within 7.130 degrees Celsius. - maxItems: 1 - items: - default: 0 - minimum: 0 - maximum: 7130 + default: 0 + minimum: 0 + maximum: 7130 additionalProperties: falseDocumentation/devicetree/bindings/hwmon/ti,tmp513.yaml +0
-1@@ -52,7 +52,6 @@ properties: ti,bus-range-microvolt: description: | This is the operating range of the bus voltage in microvolt - $ref: /schemas/types.yaml#/definitions/uint32 enum: [16000000, 32000000] default: 32000000Documentation/devicetree/bindings/i2c/i2c-gpio.yaml +0
-2@@ -39,11 +39,9 @@ properties: i2c-gpio,delay-us: description: delay between GPIO operations (may depend on each platform) - $ref: /schemas/types.yaml#/definitions/uint32 i2c-gpio,timeout-ms: description: timeout to get data - $ref: /schemas/types.yaml#/definitions/uint32 # Deprecated properties, do not use in new device tree sources: gpios:Documentation/devicetree/bindings/i2c/snps,designware-i2c.yaml +0
-3@@ -66,21 +66,18 @@ properties: default: 400000 i2c-sda-hold-time-ns: - maxItems: 1 description: | The property should contain the SDA hold time in nanoseconds. This option is only supported in hardware blocks version 1.11a or newer or on Microsemi SoCs. i2c-scl-falling-time-ns: - maxItems: 1 description: | The property should contain the SCL falling time in nanoseconds. This value is used to compute the tLOW period. default: 300 i2c-sda-falling-time-ns: - maxItems: 1 description: | The property should contain the SDA falling time in nanoseconds. This value is used to compute the tHIGH period.Documentation/devicetree/bindings/iio/adc/maxim,max9611.yaml +0
-1@@ -23,7 +23,6 @@ properties: maxItems: 1 shunt-resistor-micro-ohms: - $ref: /schemas/types.yaml#/definitions/uint32 description: | Value in micro Ohms of the shunt resistor connected between the RS+ and RS- inputs, across which the current is measured. Value needed to computeDocumentation/devicetree/bindings/iio/adc/st,stm32-adc.yaml +0
-1@@ -248,7 +248,6 @@ patternProperties: Resolution (bits) to use for conversions: - can be 6, 8, 10 or 12 on stm32f4 - can be 8, 10, 12, 14 or 16 on stm32h7 and stm32mp1 - $ref: /schemas/types.yaml#/definitions/uint32 st,adc-channels: description: |Documentation/devicetree/bindings/iio/adc/ti,palmas-gpadc.yaml +0
-2@@ -42,7 +42,6 @@ properties: const: 1 ti,channel0-current-microamp: - $ref: /schemas/types.yaml#/definitions/uint32 description: Channel 0 current in uA. enum: - 0@@ -51,7 +50,6 @@ properties: - 20 ti,channel3-current-microamp: - $ref: /schemas/types.yaml#/definitions/uint32 description: Channel 3 current in uA. enum: - 0Documentation/devicetree/bindings/iio/dac/adi,ad5758.yaml +26
-15@@ -46,31 +46,42 @@ properties: two properties must be present: adi,range-microvolt: - $ref: /schemas/types.yaml#/definitions/int32-array description: | Voltage output range specified as <minimum, maximum> - enum: - - [[0, 5000000]] - - [[0, 10000000]] - - [[-5000000, 5000000]] - - [[-10000000, 10000000]] + oneOf: + - items: + - const: 0 + - enum: [5000000, 10000000] + - items: + - const: -5000000 + - const: 5000000 + - items: + - const: -10000000 + - const: 10000000 adi,range-microamp: - $ref: /schemas/types.yaml#/definitions/int32-array description: | Current output range specified as <minimum, maximum> - enum: - - [[0, 20000]] - - [[0, 24000]] - - [[4, 24000]] - - [[-20000, 20000]] - - [[-24000, 24000]] - - [[-1000, 22000]] + oneOf: + - items: + - const: 0 + - enum: [20000, 24000] + - items: + - const: 4 + - const: 24000 + - items: + - const: -20000 + - const: 20000 + - items: + - const: -24000 + - const: 24000 + - items: + - const: -1000 + - const: 22000 reset-gpios: true adi,dc-dc-ilim-microamp: - $ref: /schemas/types.yaml#/definitions/uint32 enum: [150000, 200000, 250000, 300000, 350000, 400000] description: | The dc-to-dc converter current limit.Documentation/devicetree/bindings/iio/health/maxim,max30100.yaml +0
-1@@ -21,7 +21,6 @@ properties: description: Connected to ADC_RDY pin. maxim,led-current-microamp: - $ref: /schemas/types.yaml#/definitions/uint32-array minItems: 2 maxItems: 2 description: |Documentation/devicetree/bindings/input/touchscreen/touchscreen.yaml +0
-2@@ -70,11 +70,9 @@ properties: touchscreen-x-mm: description: horizontal length in mm of the touchscreen - $ref: /schemas/types.yaml#/definitions/uint32 touchscreen-y-mm: description: vertical length in mm of the touchscreen - $ref: /schemas/types.yaml#/definitions/uint32 dependencies: touchscreen-size-x: [ touchscreen-size-y ]Documentation/devicetree/bindings/mmc/mmc-controller.yaml +0
-1@@ -261,7 +261,6 @@ properties: waiting for I/O signalling and card power supply to be stable, regardless of whether pwrseq-simple is used. Default to 10ms if no available. - $ref: /schemas/types.yaml#/definitions/uint32 default: 10 supports-cqe:Documentation/devicetree/bindings/mmc/mmc-pwrseq-simple.yaml +0
-2@@ -41,13 +41,11 @@ properties: description: Delay in ms after powering the card and de-asserting the reset-gpios (if any). - $ref: /schemas/types.yaml#/definitions/uint32 power-off-delay-us: description: Delay in us after asserting the reset-gpios (if any) during power off of the card. - $ref: /schemas/types.yaml#/definitions/uint32 required: - compatibleDocumentation/devicetree/bindings/net/ethernet-controller.yaml +0
-2@@ -122,7 +122,6 @@ properties: such as flow control thresholds. rx-internal-delay-ps: - $ref: /schemas/types.yaml#/definitions/uint32 description: | RGMII Receive Clock Delay defined in pico seconds. This is used for controllers that have configurable RX internal delays.@@ -140,7 +139,6 @@ properties: is used for components that can have configurable fifo sizes. tx-internal-delay-ps: - $ref: /schemas/types.yaml#/definitions/uint32 description: | RGMII Transmit Clock Delay defined in pico seconds. This is used for controllers that have configurable TX internal delays.Documentation/devicetree/bindings/net/snps,dwmac.yaml +0
-1@@ -208,7 +208,6 @@ properties: Triplet of delays. The 1st cell is reset pre-delay in micro seconds. The 2nd cell is reset pulse in micro seconds. The 3rd cell is reset post-delay in micro seconds. - $ref: /schemas/types.yaml#/definitions/uint32-array minItems: 3 maxItems: 3Documentation/devicetree/bindings/power/supply/battery.yaml +0
-3@@ -83,21 +83,18 @@ properties: for each of the battery capacity lookup table. operating-range-celsius: - $ref: /schemas/types.yaml#/definitions/uint32-array description: operating temperature range of a battery items: - description: minimum temperature at which battery can operate - description: maximum temperature at which battery can operate ambient-celsius: - $ref: /schemas/types.yaml#/definitions/uint32-array description: safe range of ambient temperature items: - description: alert when ambient temperature is lower than this value - description: alert when ambient temperature is higher than this value alert-celsius: - $ref: /schemas/types.yaml#/definitions/uint32-array description: safe range of battery temperature items: - description: alert when battery temperature is lower than this valueDocumentation/devicetree/bindings/power/supply/bq2515x.yaml +0
-1@@ -50,7 +50,6 @@ properties: maxItems: 1 input-current-limit-microamp: - $ref: /schemas/types.yaml#/definitions/uint32 description: Maximum input current in micro Amps. minimum: 50000 maximum: 500000Documentation/devicetree/bindings/regulator/dlg,da9121.yaml +0
-1@@ -62,7 +62,6 @@ properties: description: IRQ line information. dlg,irq-polling-delay-passive-ms: - $ref: "/schemas/types.yaml#/definitions/uint32" minimum: 1000 maximum: 10000 description: |Documentation/devicetree/bindings/regulator/fixed-regulator.yaml +0
-2@@ -72,11 +72,9 @@ properties: startup-delay-us: description: startup time in microseconds - $ref: /schemas/types.yaml#/definitions/uint32 off-on-delay-us: description: off delay time in microseconds - $ref: /schemas/types.yaml#/definitions/uint32 enable-active-high: description:Documentation/devicetree/bindings/rtc/rtc.yaml +0
-2@@ -27,7 +27,6 @@ properties: 1: chargeable quartz-load-femtofarads: - $ref: /schemas/types.yaml#/definitions/uint32 description: The capacitive load of the quartz(x-tal), expressed in femto Farad (fF). The default value shall be listed (if optional),@@ -47,7 +46,6 @@ properties: deprecated: true trickle-resistor-ohms: - $ref: /schemas/types.yaml#/definitions/uint32 description: Selected resistor for trickle charger. Should be given if trickle charger should be enabled.Documentation/devicetree/bindings/serial/pl011.yaml +0
-2@@ -88,14 +88,12 @@ properties: description: Rate at which poll occurs when auto-poll is set. default 100ms. - $ref: /schemas/types.yaml#/definitions/uint32 default: 100 poll-timeout-ms: description: Poll timeout when auto-poll is set, default 3000ms. - $ref: /schemas/types.yaml#/definitions/uint32 default: 3000 required:Documentation/devicetree/bindings/sound/sgtl5000.yaml +0
-2@@ -41,14 +41,12 @@ properties: values of 2k, 4k or 8k. If set to 0 it will be off. If this node is not mentioned or if the value is unknown, then micbias resistor is set to 4k. - $ref: "/schemas/types.yaml#/definitions/uint32" enum: [ 0, 2, 4, 8 ] micbias-voltage-m-volts: description: The bias voltage to be used in mVolts. The voltage can take values from 1.25V to 3V by 250mV steps. If this node is not mentioned or the value is unknown, then the value is set to 1.25V. - $ref: "/schemas/types.yaml#/definitions/uint32" enum: [ 1250, 1500, 1750, 2000, 2250, 2500, 2750, 3000 ] lrclk-strength:Documentation/devicetree/bindings/watchdog/watchdog.yaml +0
-1@@ -19,7 +19,6 @@ properties: pattern: "^watchdog(@.*|-[0-9a-f])?$" timeout-sec: - $ref: /schemas/types.yaml#/definitions/uint32 description: Contains the watchdog timeout in seconds.