usb: host: ohci-platform: Disable ohci for rk3288
Subsystems (3)
PATCH 1/1 usb: host: ohci-platform: Disable ohci for rk3288
rk3288 has usb host0 ohci controller but doesn't actually work on real hardware but it works with new revision chip rk3288w.
So, disable ohci for rk3288.
For rk3288w chips the compatible update code is handled by bootloader.
---
Note:
- U-Boot patch for compatible update
https://patchwork.ozlabs.org/project/uboot/patch/[email protected]/
drivers/usb/host/ohci-platform.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/usb/host/ohci-platform.c +1 -1
@@ -96,7 +96,7 @@ static int ohci_platform_probe(struct platform_device *dev)struct ohci_hcd *ohci;int err, irq, clk =0 ; -if (usb_disabled ()) +if (usb_disabled () ||of_machine_is_compatible ("rockchip,rk3288" ))return -ENODEV ;/*
Signature · 1 line
2.25.1
Quoted 32 lines · Jagan Teki
rk3288 has usb host0 ohci controller but doesn't actually work on real hardware but it works with new revision chip rk3288w.
So, disable ohci for rk3288.
For rk3288w chips the compatible update code is handled by bootloader.
Cc William Wu <[email protected]>Signed-off-by Jagan Teki <[email protected]>---
Note:
- U-Boot patch for compatible update
https://patchwork.ozlabs.org/project/uboot/patch/[email protected]/drivers/usb/host/ohci-platform.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)drivers/usb/host/ohci-platform.c +1
-1@@ -96,7 +96,7 @@ static int ohci_platform_probe(struct platform_device *dev)struct ohci_hcd *ohci;int err, irq, clk =0 ; -if (usb_disabled ()) +if (usb_disabled () ||of_machine_is_compatible ("rockchip,rk3288" ))return -ENODEV ;/* Signature · 1 line
2.25.1
Quoted 22 lines · Jagan Teki
rk3288 has usb host0 ohci controller but doesn't actually work on real hardware but it works with new revision chip rk3288w.
So, disable ohci for rk3288.
For rk3288w chips the compatible update code is handled by bootloader.
Cc William Wu <[email protected]>Signed-off-by Jagan Teki <[email protected]>---
Note:
- U-Boot patch for compatible update
https://patchwork.ozlabs.org/project/uboot/patch/[email protected]/drivers/usb/host/ohci-platform.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)drivers/usb/host/ohci-platform.c +0
-0
drivers/usb/host/ohci-platform.c static int ohci_platform_probe(struct platform_device *dev) · line 99
Quoted 5 lines
drivers/usb/host/ohci-platform.c +1
-1@@ -96,7 +96,7 @@ static int ohci_platform_probe(struct platform_device *dev)struct ohci_hcd *ohci;int err, irq, clk =0 ; -if (usb_disabled ()) +if (usb_disabled () ||of_machine_is_compatible ("rockchip,rk3288" ))
This seems unnecessary to me - if we've even started probing a driver for a broken piece of hardware to the point that we need magic checks to bail out again, then something is already fundamentally wrong.
Old boards only sold with the original SoC variant have no reason to enable the OHCI (since it never worked originally), thus will never execute this check.
New boards designed around the W variant to make use of the OHCI can freely enable it either way.
The only relative-edge-case where it might matter is older board designs still in production which have shipped with both SoC variants. Enabling OHCI can't be *necessary* given that it's still broken on a lot of deployed boards, so at best it must be an opportunistic nice-to-have. Since we're already having to rely on the bootloader to patch up the devicetree for other low-level differences in this case, it should be part of that responsibility for it to only enable the OHCI on the appropriate SoC variant too. Statically enabling it in the DTS for a board where it may well not work is just bad.
As soon as a DTB with a broken piece of hardware enabled gets passed to an OS, then the damage is already done. A driver patch in a future version of Linux that magically knows better and ignores it isn't going to help a user booting an older kernel image, or some other OS entirely.
Robin.
Quoted 4 lines
drivers/usb/host/ohci-platform.c +0
-0return -ENODEV ;/*
Quoted 41 lines · Robin Murphy
Quoted 22 lines · Jagan Teki
rk3288 has usb host0 ohci controller but doesn't actually work on real hardware but it works with new revision chip rk3288w.
So, disable ohci for rk3288.
For rk3288w chips the compatible update code is handled by bootloader.
Cc William Wu <[email protected]>Signed-off-by Jagan Teki <[email protected]>---
Note:
- U-Boot patch for compatible update
https://patchwork.ozlabs.org/project/uboot/patch/[email protected]/drivers/usb/host/ohci-platform.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)drivers/usb/host/ohci-platform.c +0
-0drivers/usb/host/ohci-platform.c static int ohci_platform_probe(struct platform_device *dev) · line 99
Quoted 5 lines
drivers/usb/host/ohci-platform.c +1
-1@@ -96,7 +96,7 @@ static int ohci_platform_probe(struct platform_device *dev)struct ohci_hcd *ohci;int err, irq, clk =0 ; -if (usb_disabled ()) +if (usb_disabled () ||of_machine_is_compatible ("rockchip,rk3288" ))This seems unnecessary to me - if we've even started probing a driver for a broken piece of hardware to the point that we need magic checks to bail out again, then something is already fundamentally wrong.
Old boards only sold with the original SoC variant have no reason to enable the OHCI (since it never worked originally), thus will never execute this check.
New boards designed around the W variant to make use of the OHCI can freely enable it either way.
Quoted 9 lines
The only relative-edge-case where it might matter is older board designs still in production which have shipped with both SoC variants. Enabling OHCI can't be *necessary* given that it's still broken on a lot of deployed boards, so at best it must be an opportunistic nice-to-have. Since we're already having to rely on the bootloader to patch up the devicetree for other low-level differences in this case, it should be part of that responsibility for it to only enable the OHCI on the appropriate SoC variant too. Statically enabling it in the DTS for a board where it may well not work is just bad.
You mean enable OHCI by identifying revision W with dts status "okay"? doesn't it complex for the bootloader to update all effecting changes?
Jagan.
Quoted 52 lines · Jagan Teki
Quoted 41 lines · Robin Murphy
Quoted 22 lines · Jagan Teki
rk3288 has usb host0 ohci controller but doesn't actually work on real hardware but it works with new revision chip rk3288w.
So, disable ohci for rk3288.
For rk3288w chips the compatible update code is handled by bootloader.
Cc William Wu <[email protected]>Signed-off-by Jagan Teki <[email protected]>---
Note:
- U-Boot patch for compatible update
https://patchwork.ozlabs.org/project/uboot/patch/[email protected]/drivers/usb/host/ohci-platform.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)drivers/usb/host/ohci-platform.c +0
-0drivers/usb/host/ohci-platform.c static int ohci_platform_probe(struct platform_device *dev) · line 99
Quoted 5 lines
drivers/usb/host/ohci-platform.c +1
-1@@ -96,7 +96,7 @@ static int ohci_platform_probe(struct platform_device *dev)struct ohci_hcd *ohci;int err, irq, clk =0 ; -if (usb_disabled ()) +if (usb_disabled () ||of_machine_is_compatible ("rockchip,rk3288" ))This seems unnecessary to me - if we've even started probing a driver for a broken piece of hardware to the point that we need magic checks to bail out again, then something is already fundamentally wrong.
Old boards only sold with the original SoC variant have no reason to enable the OHCI (since it never worked originally), thus will never execute this check.
New boards designed around the W variant to make use of the OHCI can freely enable it either way.
Quoted 9 lines
The only relative-edge-case where it might matter is older board designs still in production which have shipped with both SoC variants. Enabling OHCI can't be *necessary* given that it's still broken on a lot of deployed boards, so at best it must be an opportunistic nice-to-have. Since we're already having to rely on the bootloader to patch up the devicetree for other low-level differences in this case, it should be part of that responsibility for it to only enable the OHCI on the appropriate SoC variant too. Statically enabling it in the DTS for a board where it may well not work is just bad.
Quoted 2 lines
You mean enable OHCI by identifying revision W with dts status "okay"? doesn't it complex for the bootloader to update all effecting changes?
Well, on boards which may have either SoC it's already got to detect the difference and make at least a couple of other DT adjustments; a handful more lines to check for a specific node and flip its status wouldn't be too horrendous (although I suppose you'd also want to check whether the EHCI is enabled first, to guess at whether the port's even wired up at all).
Or alternatively, as I said, simply don't bother doing anything - boards that only use RK3288W can enable OHCI in their DTS, and other boards that have been not using it for however many years can continue not using it even if it might technically be available on newer production runs.
Robin.