usb: dwc2: disable erroneous overcurrent condition
Subsystems (2)
PATCH 1/1 usb: dwc2: disable erroneous overcurrent condition
For the case where an external VBUS is used, we should enable the external VBUS comparator in the driver. This would prevent an unnecessary overcurrent error which would then disable the host port.
This patch uses the standard 'disable-over-current' binding to allow of the option of disabling the over-current condition.
--- drivers/usb/dwc2/core.h | 4 ++++ drivers/usb/dwc2/hcd.c | 5 +++++ drivers/usb/dwc2/params.c | 3 +++ 3 files changed, 12 insertions(+)
drivers/usb/dwc2/core.h +4 -0
@@ -395,6 +395,9 @@ enum dwc2_ep0_state {* (default when phy_type is UTMI+ or ULPI) * 1 - 6 MHz * (default when phy_type is Full Speed) +* @oc_disable: Flag to disable overcurrent condition. +* 0 - Allow overcurrent condition to get detected +* 1 - Disable overcurrent condtion to get detected * @ts_dline: Enable Term Select Dline pulsing * 0 - No (default) * 1 - Yes
@@ -492,6 +495,7 @@ struct dwc2_core_params {bool dma_desc_fs_enable;bool host_support_fs_ls_low_power;bool host_ls_low_power_phy_clk; +bool oc_disable;u8 host_channels;u16 host_rx_fifo_size;
drivers/usb/dwc2/hcd.c +5 -0
@@ -213,6 +213,11 @@ static int dwc2_hs_phy_init(struct dwc2_hsotg *hsotg, bool select_phy) usbcfg &= ~(GUSBCFG_PHYIF16 |GUSBCFG_DDRSEL );if (hsotg->params.phy_ulpi_ddr) usbcfg |=GUSBCFG_DDRSEL ; + +/* Set external VBUS indicator as needed. */ +if (hsotg->params.oc_disable) + usbcfg |= (GUSBCFG_ULPI_INT_VBUS_IND | +GUSBCFG_INDICATORPASSTHROUGH );break ;case DWC2_PHY_TYPE_PARAM_UTMI :/* UTMI+ interface */
drivers/usb/dwc2/params.c +3 -0
@@ -335,6 +335,9 @@ static void dwc2_get_device_properties(struct dwc2_hsotg *hsotg) num); } } + +if (of_find_property (hsotg->dev->of_node,"disable-over-current" ,NULL )) + p->oc_disable = true; }static void dwc2_check_param_otg_cap (struct dwc2_hsotg *hsotg)
Signature · 1 line
2.7.4
Quoted 8 lines · Dinh Nguyen
For the case where an external VBUS is used, we should enable the external VBUS comparator in the driver. This would prevent an unnecessary overcurrent error which would then disable the host port.
This patch uses the standard 'disable-over-current' binding to allow of the option of disabling the over-current condition.
Signed-off-by Dinh Nguyen <[email protected]>
Similar patch was in U-Boot for two years now and it does the trick indeed.
Quoted 59 lines
--- drivers/usb/dwc2/core.h | 4 ++++ drivers/usb/dwc2/hcd.c | 5 +++++ drivers/usb/dwc2/params.c | 3 +++ 3 files changed, 12 insertions(+)drivers/usb/dwc2/core.h +4
-0@@ -395,6 +395,9 @@ enum dwc2_ep0_state {* (default when phy_type is UTMI+ or ULPI) * 1 - 6 MHz * (default when phy_type is Full Speed) +* @oc_disable: Flag to disable overcurrent condition. +* 0 - Allow overcurrent condition to get detected +* 1 - Disable overcurrent condtion to get detected * @ts_dline: Enable Term Select Dline pulsing * 0 - No (default) * 1 - Yes @@ -492,6 +495,7 @@ struct dwc2_core_params {bool dma_desc_fs_enable;bool host_support_fs_ls_low_power;bool host_ls_low_power_phy_clk; +bool oc_disable;u8 host_channels;u16 host_rx_fifo_size;drivers/usb/dwc2/hcd.c +5
-0@@ -213,6 +213,11 @@ static int dwc2_hs_phy_init(struct dwc2_hsotg *hsotg, bool select_phy) usbcfg &= ~(GUSBCFG_PHYIF16 |GUSBCFG_DDRSEL );if (hsotg->params.phy_ulpi_ddr) usbcfg |=GUSBCFG_DDRSEL ; + +/* Set external VBUS indicator as needed. */ +if (hsotg->params.oc_disable) + usbcfg |= (GUSBCFG_ULPI_INT_VBUS_IND | +GUSBCFG_INDICATORPASSTHROUGH );break ;case DWC2_PHY_TYPE_PARAM_UTMI :/* UTMI+ interface */ drivers/usb/dwc2/params.c +3
-0@@ -335,6 +335,9 @@ static void dwc2_get_device_properties(struct dwc2_hsotg *hsotg) num); } } + +if (of_find_property (hsotg->dev->of_node,"disable-over-current" ,NULL )) + p->oc_disable = true; }static void dwc2_check_param_otg_cap (struct dwc2_hsotg *hsotg)
Signature · 2 lines
Best regards, Marek Vasut
Minas Harutyunyan
Acked-byQuoted 71 lines · Marek Vasut
Quoted 8 lines · Dinh Nguyen
For the case where an external VBUS is used, we should enable the external VBUS comparator in the driver. This would prevent an unnecessary overcurrent error which would then disable the host port.
This patch uses the standard 'disable-over-current' binding to allow of the option of disabling the over-current condition.
Signed-off-by Dinh Nguyen <[email protected]>Reviewed-by Marek Vasut <[email protected]>Similar patch was in U-Boot for two years now and it does the trick indeed.
Quoted 57 lines
--- drivers/usb/dwc2/core.h | 4 ++++ drivers/usb/dwc2/hcd.c | 5 +++++ drivers/usb/dwc2/params.c | 3 +++ 3 files changed, 12 insertions(+)drivers/usb/dwc2/core.h +4
-0@@ -395,6 +395,9 @@ enum dwc2_ep0_state {* (default when phy_type is UTMI+ or ULPI) * 1 - 6 MHz * (default when phy_type is Full Speed) +* @oc_disable: Flag to disable overcurrent condition. +* 0 - Allow overcurrent condition to get detected +* 1 - Disable overcurrent condtion to get detected * @ts_dline: Enable Term Select Dline pulsing * 0 - No (default) * 1 - Yes @@ -492,6 +495,7 @@ struct dwc2_core_params {bool dma_desc_fs_enable;bool host_support_fs_ls_low_power;bool host_ls_low_power_phy_clk; +bool oc_disable;u8 host_channels;u16 host_rx_fifo_size;drivers/usb/dwc2/hcd.c +5
-0@@ -213,6 +213,11 @@ static int dwc2_hs_phy_init(struct dwc2_hsotg *hsotg, bool select_phy) usbcfg &= ~(GUSBCFG_PHYIF16 |GUSBCFG_DDRSEL );if (hsotg->params.phy_ulpi_ddr) usbcfg |=GUSBCFG_DDRSEL ; + +/* Set external VBUS indicator as needed. */ +if (hsotg->params.oc_disable) + usbcfg |= (GUSBCFG_ULPI_INT_VBUS_IND | +GUSBCFG_INDICATORPASSTHROUGH );break ;case DWC2_PHY_TYPE_PARAM_UTMI :/* UTMI+ interface */ drivers/usb/dwc2/params.c +3
-0@@ -335,6 +335,9 @@ static void dwc2_get_device_properties(struct dwc2_hsotg *hsotg) num); } } + +if (of_find_property (hsotg->dev->of_node,"disable-over-current" ,NULL )) + p->oc_disable = true; }
Quoted 4 lines
drivers/usb/dwc2/params.c static void dwc2_get_device_properties(struct dwc2_hsotg *hsotg) · line 343
Quoted 2 lines
drivers/usb/dwc2/params.c +0
-0static void dwc2_check_param_otg_cap (struct dwc2_hsotg *hsotg)
Hi John Youn, I checked with HW team - patch is OK.
A message that is not in the archive (sent off-list or not yet received): [email protected]
A message that is not in the archive (sent off-list or not yet received): [email protected]
A message that is not in the archive (sent off-list or not yet received): 32EB88BF8EC1614E9FB18BD3718BE1A1163C1882@am04wembxa.internal.synopsys.com
A message that is not in the archive (sent off-list or not yet received): [email protected]
A message that is not in the archive (sent off-list or not yet received): 410670D7E743164D87FA6160E7907A560113A31DA7@am04wembxa.internal.synopsys.com
[U-Boot] dwc2: usb: Unable to clear channel error
Quoted 56 lines · Minas Harutyunyan
Quoted 55 lines · Dinh Nguyen
Quoted 40 lines · Grigor Tovmasyan
Quoted 39 lines · Marek Vasut
Quoted 37 lines · Dinh Nguyen
Hi,
I'm trying to bringup the DWC2 USB IP version 330A on a new Stratix10 SoC and have encountered this error in both Linux and U-Boot:
U-Boot(version v2017.09)
# usb start starting USB... USB0: Core Release: 3.30a dwc_otg_core_host_init: Timeout! dwc_otg_core_host_init: Timeout!Linux(kernel v4.13)
[ 1.299891] dwc2 ffb00000.usb: DWC OTG Controller [ 1.304628] dwc2 ffb00000.usb: new USB bus registered, assigned bus number 1 [ 1.311698] dwc2 ffb00000.usb: irq 13, io mem 0xffb00000 [ 1.318309] dwc2 ffb00000.usb: Unable to clear enable on channel 0 [ 1.325749] dwc2 ffb00000.usb: Unable to clear enable on channel 1 [ 1.333187] dwc2 ffb00000.usb: Unable to clear enable on channel 2 [ 1.340626] dwc2 ffb00000.usb: Unable to clear enable on channel 3 [ 1.348064] dwc2 ffb00000.usb: Unable to clear enable on channel 4 [ 1.355503] dwc2 ffb00000.usb: Unable to clear enable on channel 5 [ 1.362941] dwc2 ffb00000.usb: Unable to clear enable on channel 6 [ 1.370379] dwc2 ffb00000.usb: Unable to clear enable on channel 7 [ 1.377818] dwc2 ffb00000.usb: Unable to clear enable on channel 8 [ 1.385256] dwc2 ffb00000.usb: Unable to clear enable on channel 9 [ 1.392694] dwc2 ffb00000.usb: Unable to clear enable on channel 10 [ 1.400218] dwc2 ffb00000.usb: Unable to clear enable on channel 11 [ 1.407743] dwc2 ffb00000.usb: Unable to clear enable on channel 12 [ 1.415269] dwc2 ffb00000.usb: Unable to clear enable on channel 13 [ 1.422794] dwc2 ffb00000.usb: Unable to clear enable on channel 14Just wondering if anyone might have an idea on what could be causing this error?
Quoted 9 lines
Quoted 2 lines
Maybe some clock are not enabled ?
Hi ,
Are you following board/hisilicon/hikey/README file instructions when using U-Boot? Specially paragraph FLASHING point 4, where discussed "
dwc_otg_core_host_init: Timeout!" message.I saw that, but I don't know how that applies to a Stratix10 platform?
Quoted 8 lines
Quoted 3 lines
Dinh
Hi,
Did you able to resolve this issue? If not, please provide verbose debug log and register dump.
I double-checked the clocks and it looks like all of the necessary clocks are enabled. Here are the log and register dump for U-Boot, I'll follow-up with the Linux log shortly.
For U-Boot:
SOCFPGA_STRATIX10 # usb start
starting USB...
USB0: Core Release: 3.30adwc_otg_core_host_init: Timeout (reg=00000000ffb00500 mask=80000000 wait_set=0)dwc_otg_core_host_init: Timeout!dwc_otg_core_host_init: Timeout (reg=00000000ffb00520 mask=80000000 wait_set=0)dwc_otg_core_host_init: Timeout!dwc_otg_core_host_init: Timeout (reg=00000000ffb00540 mask=80000000 wait_set=0)dwc_otg_core_host_init: Timeout!dwc_otg_core_host_init: Timeout (reg=00000000ffb00560 mask=80000000 wait_set=0)dwc_otg_core_host_init: Timeout!dwc_otg_core_host_init: Timeout (reg=00000000ffb00580 mask=80000000 wait_set=0)dwc_otg_core_host_init: Timeout!dwc_otg_core_host_init: Timeout (reg=00000000ffb005a0 mask=80000000 wait_set=0)dwc_otg_core_host_init: Timeout!dwc_otg_core_host_init: Timeout (reg=00000000ffb005c0 mask=80000000 wait_set=0)dwc_otg_core_host_init: Timeout!dwc_otg_core_host_init: Timeout (reg=00000000ffb005e0 mask=80000000 wait_set=0)dwc_otg_core_host_init: Timeout!dwc_otg_core_host_init: Timeout (reg=00000000ffb00600 mask=80000000 wait_set=0)dwc_otg_core_host_init: Timeout!dwc_otg_core_host_init: Timeout (reg=00000000ffb00620 mask=80000000 wait_set=0)dwc_otg_core_host_init: Timeout!dwc_otg_core_host_init: Timeout (reg=00000000ffb00640 mask=80000000 wait_set=0)dwc_otg_core_host_init: Timeout!dwc_otg_core_host_init: Timeout (reg=00000000ffb00660 mask=80000000 wait_set=0)dwc_otg_core_host_init: Timeout!dwc_otg_core_host_init: Timeout (reg=00000000ffb00680 mask=80000000 wait_set=0)dwc_otg_core_host_init: Timeout!dwc_otg_core_host_init: Timeout (reg=00000000ffb006a0 mask=80000000 wait_set=0)dwc_otg_core_host_init: Timeout!dwc_otg_core_host_init: Timeout (reg=00000000ffb006c0 mask=80000000 wait_set=0)dwc_otg_core_host_init: Timeout!
scanning bus 0 for devices... dwc2_submit_control_msg:
dev='usb at ffb00000', udev=000000003fa50380, udev->dev='usb at ffb00000', portnr=0dwc2_submit_control_msg: dev='usb at ffb00000', udev=000000003fa50380, udev->dev='usb at ffb00000', portnr=0dwc2_submit_control_msg: dev='usb at ffb00000', udev=000000003fa50380, udev->dev='usb at ffb00000', portnr=0dwc2_submit_control_msg: dev='usb at ffb00000', udev=000000003fa50380, udev->dev='usb at ffb00000', portnr=0dwc2_submit_control_msg: dev='usb at ffb00000', udev=000000003fa50380, udev->dev='usb at ffb00000', portnr=0dwc2_submit_control_msg: dev='usb at ffb00000', udev=000000003fa50380, udev->dev='usb at ffb00000', portnr=0dwc2_submit_control_msg: dev='usb at ffb00000', udev=000000003fa50380, udev->dev='usb at ffb00000', portnr=0dwc2_submit_control_msg: dev='usb at ffb00000', udev=000000003fa50380, udev->dev='usb at ffb00000', portnr=0dwc2_submit_control_msg: dev='usb at ffb00000', udev=000000003fa55080, udev->dev='usb_hub', portnr=0dwc2_submit_control_msg: dev='usb at ffb00000', udev=000000003fa55080, udev->dev='usb_hub', portnr=0dwc2_submit_control_msg: dev='usb at ffb00000', udev=000000003fa55080, udev->dev='usb_hub', portnr=0dwc2_submit_control_msg: dev='usb at ffb00000', udev=000000003fa55080, udev->dev='usb_hub', portnr=0dwc2_submit_control_msg: dev='usb at ffb00000', udev=000000003fa55080, udev->dev='usb_hub', portnr=0dwc2_submit_control_msg: dev='usb at ffb00000', udev=000000003fa55080, udev->dev='usb_hub', portnr=0dwc2_submit_control_msg: dev='usb at ffb00000', udev=000000003fa55080, udev->dev='usb_hub', portnr=0dwc2_submit_control_msg: dev='usb at ffb00000', udev=000000003fa55080, udev->dev='usb_hub', portnr=0dwc2_submit_control_msg: dev='usb at ffb00000', udev=000000003fa55080, udev->dev='usb_hub', portnr=0dwc2_submit_control_msg: dev='usb at ffb00000', udev=000000003fa55080, udev->dev='usb_hub', portnr=0dwc2_submit_control_msg: dev='usb at ffb00000', udev=000000003fa4f440, udev->dev='usb_hub', portnr=1chunk_msg: msg: pipe 80000083 pid 3 in 0 len 8transfer_chunk: chunk: pid 3 xfer_len 8 pkts 1wait_for_chhltd: Timeout (reg=00000000ffb00508 mask=00000002 wait_set=1) unable to get device descriptor (error=-110)dwc2_submit_control_msg: dev='usb at ffb00000', udev=000000003fa55080, udev->dev='usb_hub', portnr=0
1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) foundSOCFPGA_STRATIX10
Before "usb start", the registers are:
ffb00000: 00200000 00000000 00000000 00001410 .. .............ffb00010: 80000000 04000021 00000000 00000000 ....!...........ffb00020: 00000000 00002000 20002000 00082000 ..... ... . . ..ffb00030: 00000000 00000000 00000000 12345678 ............xV4.ffb00040: 4f54330a 00000000 238ffc90 1f8002e8 .3TO.......#....ffb00050: fe0f0020 00000000 00000000 1f802000 ............ ..ffb00060: 00000000 00000000 00000000 00000000 ................ffb00070: 00000000 00000000 00000000 00000000 ................ffb00080: 00000000 00000000 00000000 00000000 ................ffb00090: 00000000 00000000 00000000 00000000 ................ffb000a0: 00000000 00000000 00000000 00000000 ................ffb000b0: 00000000 00000000 00000000 00000000 ................ffb000c0: 00000000 00000000 00000000 00000000 ................ffb000d0: 00000000 00000000 00000000 00000000 ................ffb000e0: 00000000 00000000 00000000 00000000 ................ffb000f0: 00000000 00000000 00000000 00000000 ................ffb00100: 20004000 00000000 00000000 00000000 . at . ............ffb00110: 00000000 00000000 00000000 00000000 ................ffb00120: 00000000 00000000 00000000 00000000 ................ffb00130: 00000000 00000000 00000000 00000000 ................ffb00140: 00000000 00000000 00000000 00000000 ................ffb00150: 00000000 00000000 00000000 00000000 ................ffb00160: 00000000 00000000 00000000 00000000 ................ffb00170: 00000000 00000000 00000000 00000000 ................ffb00180: 00000000 00000000 00000000 00000000 ................
ffb00500: 00000000 00000000 00000000 00000000 ................ffb00510: 00000000 ffffff7f 00000000 ffffff7f ................ffb00520: 00000000 00000000 00000000 00000000 ................ffb00530: 00000000 ffffff7f 00002000 ffffff7f ......... ......ffb00540: 00000000 00000000 00000000 00000000 ................ffb00550: 00000000 ffffff7f 00002000 ffffff7f ......... ......ffb00560: 00000000 00000000 00000000 00000000 ................ffb00570: 00000000 ffffff7f 00002000 ffffff7f ......... ......ffb00580: 00000000 00000000 00000000 00000000 ................ffb00590: 00000000 ffffff7f 00002000 ffffff7f ......... ......ffb005a0: 00000000 00000000 00000000 00000000 ................ffb005b0: 00000000 ffffff7f 00002000 ffffff7f ......... ......ffb005c0: 00000000 00000000 00000000 00000000 ................ffb005d0: 00000000 ffffff7f 00002000 ffffff7f ......... ......ffb005e0: 00000000 00000000 00000000 00000000 ................ffb005f0: 00000000 ffffff7f 00002000 ffffff7f ......... ......ffb00600: 00000000 00000000 00000000 00000000 ................ffb00610: 00000000 ffffff7f 00002000 ffffff7f ......... ......ffb00620: 00000000 00000000 00000000 00000000 ................ffb00630: 00000000 ffffff7f 00002000 ffffff7f ......... ......ffb00640: 00000000 00000000 00000000 00000000 ................ffb00650: 00000000 ffffff7f 00002000 ffffff7f ......... ......ffb00660: 00000000 00000000 00000000 00000000 ................ffb00670: 00000000 ffffff7f 00002000 ffffff7f ......... ......ffb00680: 00000000 00000000 00000000 00000000 ................
After "usb start":
# md.l 0xffb00000 64 ffb00000: 002e0000 00080000 00000026 01301710 ........&.....0. ffb00010: 80000000 3500002d 00000000 ffffff7f ....-..5........ ffb00020: ffffff7f 00000214 01000214 47080100 ...............G ffb00030: 00000000 00000000 00000000 12345678 ............xV4. ffb00040: 4f54330a 00000000 238ffc90 1f8002e8 .3TO.......#.... ffb00050: fe0f0020 00000000 00000000 1f802000 ............ .. ffb00060: 00000000 00000000 00000000 00000000 ................ ffb00070: 00000000 00000000 00000000 00000000 ................ ffb00080: 00000000 00000000 00000000 00000000 ................ ffb00090: 00000000 00000000 00000000 00000000 ................ ffb000a0: 00000000 00000000 00000000 00000000 ................ ffb000b0: 00000000 00000000 00000000 00000000 ................ ffb000c0: 00000000 00000000 00000000 00000000 ................ ffb000d0: 00000000 00000000 00000000 00000000 ................ ffb000e0: 00000000 00000000 00000000 00000000 ................ ffb000f0: 00000000 00000000 00000000 00000000 ................ ffb00100: 02000314 00000000 00000000 00000000 ................ ffb00110: 00000000 00000000 00000000 00000000 ................ ffb00120: 00000000 00000000 00000000 00000000 ................ ffb00130: 00000000 00000000 00000000 00000000 ................ ffb00140: 00000000 00000000 00000000 00000000 ................ ffb00150: 00000000 00000000 00000000 00000000 ................ ffb00160: 00000000 00000000 00000000 00000000 ................ ffb00170: 00000000 00000000 00000000 00000000 ................ ffb00180: 00000000 00000000 00000000 00000000 ................
# md.l 0xffb00500 64 ffb00500: c0100040 00000000 00000000 00000000 @............... ffb00510: 60080008 ffffff7f 00000000 ffffff7f ...`............ ffb00520: c0000000 00000000 00000000 00000000 ................ ffb00530: 00000000 ffffff7f 00000100 ffffff7f ................ ffb00540: c0000000 00000000 00000000 00000000 ................ ffb00550: 00000000 ffffff7f 00000100 ffffff7f ................ ffb00560: c0000000 00000000 00000000 00000000 ................ ffb00570: 00000000 ffffff7f 00000100 ffffff7f ................ ffb00580: c0000000 00000000 00000000 00000000 ................ ffb00590: 00000000 ffffff7f 00000100 ffffff7f ................ ffb005a0: c0000000 00000000 00000000 00000000 ................ ffb005b0: 00000000 ffffff7f 00000100 ffffff7f ................ ffb005c0: c0000000 00000000 00000000 00000000 ................ ffb005d0: 00000000 ffffff7f 00000100 ffffff7f ................ ffb005e0: c0000000 00000000 00000000 00000000 ................ ffb005f0: 00000000 ffffff7f 00000100 ffffff7f ................ ffb00600: c0000000 00000000 00000000 00000000 ................ ffb00610: 00000000 ffffff7f 00000100 ffffff7f ................ ffb00620: c0000000 00000000 00000000 00000000 ................ ffb00630: 00000000 ffffff7f 00000100 ffffff7f ................ ffb00640: c0000000 00000000 00000000 00000000 ................ ffb00650: 00000000 ffffff7f 00000100 ffffff7f ................ ffb00660: c0000000 00000000 00000000 00000000 ................ ffb00670: 00000000 ffffff7f 00000100 ffffff7f ................ ffb00680: c0000000 00000000 00000000 00000000 ................
I'll follow up the the Linux debug output shortly.
Dinh
[U-Boot] dwc2: usb: Unable to clear channel error
Quoted 284 lines · Dinh Nguyen
Quoted 56 lines · Minas Harutyunyan
Quoted 55 lines · Dinh Nguyen
Quoted 40 lines · Grigor Tovmasyan
Quoted 39 lines · Marek Vasut
Quoted 37 lines · Dinh Nguyen
Hi,
I'm trying to bringup the DWC2 USB IP version 330A on a new Stratix10 SoC and have encountered this error in both Linux and U-Boot:
U-Boot(version v2017.09)
# usb start starting USB... USB0: Core Release: 3.30a dwc_otg_core_host_init: Timeout! dwc_otg_core_host_init: Timeout!Linux(kernel v4.13)
[ 1.299891] dwc2 ffb00000.usb: DWC OTG Controller [ 1.304628] dwc2 ffb00000.usb: new USB bus registered, assigned bus number 1 [ 1.311698] dwc2 ffb00000.usb: irq 13, io mem 0xffb00000 [ 1.318309] dwc2 ffb00000.usb: Unable to clear enable on channel 0 [ 1.325749] dwc2 ffb00000.usb: Unable to clear enable on channel 1 [ 1.333187] dwc2 ffb00000.usb: Unable to clear enable on channel 2 [ 1.340626] dwc2 ffb00000.usb: Unable to clear enable on channel 3 [ 1.348064] dwc2 ffb00000.usb: Unable to clear enable on channel 4 [ 1.355503] dwc2 ffb00000.usb: Unable to clear enable on channel 5 [ 1.362941] dwc2 ffb00000.usb: Unable to clear enable on channel 6 [ 1.370379] dwc2 ffb00000.usb: Unable to clear enable on channel 7 [ 1.377818] dwc2 ffb00000.usb: Unable to clear enable on channel 8 [ 1.385256] dwc2 ffb00000.usb: Unable to clear enable on channel 9 [ 1.392694] dwc2 ffb00000.usb: Unable to clear enable on channel 10 [ 1.400218] dwc2 ffb00000.usb: Unable to clear enable on channel 11 [ 1.407743] dwc2 ffb00000.usb: Unable to clear enable on channel 12 [ 1.415269] dwc2 ffb00000.usb: Unable to clear enable on channel 13 [ 1.422794] dwc2 ffb00000.usb: Unable to clear enable on channel 14Just wondering if anyone might have an idea on what could be causing this error?
Quoted 9 lines
Quoted 2 lines
Maybe some clock are not enabled ?
Hi ,
Are you following board/hisilicon/hikey/README file instructions when using U-Boot? Specially paragraph FLASHING point 4, where discussed "
dwc_otg_core_host_init: Timeout!" message.I saw that, but I don't know how that applies to a Stratix10 platform?
Quoted 8 lines
Quoted 3 lines
Dinh
Hi,
Did you able to resolve this issue? If not, please provide verbose debug log and register dump.
I double-checked the clocks and it looks like all of the necessary clocks are enabled. Here are the log and register dump for U-Boot, I'll follow-up with the Linux log shortly.
For U-Boot:
SOCFPGA_STRATIX10# usb start
starting USB...
USB0: Core Release: 3.30adwc_otg_core_host_init: Timeout (reg=00000000ffb00500 mask=80000000 wait_set=0)dwc_otg_core_host_init: Timeout!dwc_otg_core_host_init: Timeout (reg=00000000ffb00520 mask=80000000 wait_set=0)dwc_otg_core_host_init: Timeout!dwc_otg_core_host_init: Timeout (reg=00000000ffb00540 mask=80000000 wait_set=0)dwc_otg_core_host_init: Timeout!dwc_otg_core_host_init: Timeout (reg=00000000ffb00560 mask=80000000 wait_set=0)dwc_otg_core_host_init: Timeout!dwc_otg_core_host_init: Timeout (reg=00000000ffb00580 mask=80000000 wait_set=0)dwc_otg_core_host_init: Timeout!dwc_otg_core_host_init: Timeout (reg=00000000ffb005a0 mask=80000000 wait_set=0)dwc_otg_core_host_init: Timeout!dwc_otg_core_host_init: Timeout (reg=00000000ffb005c0 mask=80000000 wait_set=0)dwc_otg_core_host_init: Timeout!dwc_otg_core_host_init: Timeout (reg=00000000ffb005e0 mask=80000000 wait_set=0)dwc_otg_core_host_init: Timeout!dwc_otg_core_host_init: Timeout (reg=00000000ffb00600 mask=80000000 wait_set=0)dwc_otg_core_host_init: Timeout!dwc_otg_core_host_init: Timeout (reg=00000000ffb00620 mask=80000000 wait_set=0)dwc_otg_core_host_init: Timeout!dwc_otg_core_host_init: Timeout (reg=00000000ffb00640 mask=80000000 wait_set=0)dwc_otg_core_host_init: Timeout!dwc_otg_core_host_init: Timeout (reg=00000000ffb00660 mask=80000000 wait_set=0)dwc_otg_core_host_init: Timeout!dwc_otg_core_host_init: Timeout (reg=00000000ffb00680 mask=80000000 wait_set=0)dwc_otg_core_host_init: Timeout!dwc_otg_core_host_init: Timeout (reg=00000000ffb006a0 mask=80000000 wait_set=0)dwc_otg_core_host_init: Timeout!dwc_otg_core_host_init: Timeout (reg=00000000ffb006c0 mask=80000000 wait_set=0)dwc_otg_core_host_init: Timeout!
scanning bus 0 for devices...dwc2_submit_control_msg:
dev='usb atffb00000', udev=000000003fa50380, udev->dev='usb atffb00000', portnr=0dwc2_submit_control_msg: dev='usb atffb00000', udev=000000003fa50380, udev->dev='usb atffb00000', portnr=0dwc2_submit_control_msg: dev='usb atffb00000', udev=000000003fa50380, udev->dev='usb atffb00000', portnr=0dwc2_submit_control_msg: dev='usb atffb00000', udev=000000003fa50380, udev->dev='usb atffb00000', portnr=0dwc2_submit_control_msg: dev='usb atffb00000', udev=000000003fa50380, udev->dev='usb atffb00000', portnr=0dwc2_submit_control_msg: dev='usb atffb00000', udev=000000003fa50380, udev->dev='usb atffb00000', portnr=0dwc2_submit_control_msg: dev='usb atffb00000', udev=000000003fa50380, udev->dev='usb atffb00000', portnr=0dwc2_submit_control_msg: dev='usb atffb00000', udev=000000003fa50380, udev->dev='usb atffb00000', portnr=0dwc2_submit_control_msg: dev='usb atffb00000', udev=000000003fa55080, udev->dev='usb_hub', portnr=0dwc2_submit_control_msg: dev='usb atffb00000', udev=000000003fa55080, udev->dev='usb_hub', portnr=0dwc2_submit_control_msg: dev='usb atffb00000', udev=000000003fa55080, udev->dev='usb_hub', portnr=0dwc2_submit_control_msg: dev='usb atffb00000', udev=000000003fa55080, udev->dev='usb_hub', portnr=0dwc2_submit_control_msg: dev='usb atffb00000', udev=000000003fa55080, udev->dev='usb_hub', portnr=0dwc2_submit_control_msg: dev='usb atffb00000', udev=000000003fa55080, udev->dev='usb_hub', portnr=0dwc2_submit_control_msg: dev='usb atffb00000', udev=000000003fa55080, udev->dev='usb_hub', portnr=0dwc2_submit_control_msg: dev='usb atffb00000', udev=000000003fa55080, udev->dev='usb_hub', portnr=0dwc2_submit_control_msg: dev='usb atffb00000', udev=000000003fa55080, udev->dev='usb_hub', portnr=0dwc2_submit_control_msg: dev='usb atffb00000', udev=000000003fa55080, udev->dev='usb_hub', portnr=0dwc2_submit_control_msg: dev='usb atffb00000', udev=000000003fa4f440, udev->dev='usb_hub', portnr=1chunk_msg: msg: pipe 80000083 pid 3 in 0 len 8transfer_chunk: chunk: pid 3xfer_len8 pkts 1wait_for_chhltd: Timeout (reg=00000000ffb00508 mask=00000002 wait_set=1) unable to get device descriptor (error=-110)dwc2_submit_control_msg: dev='usb atffb00000', udev=000000003fa55080, udev->dev='usb_hub', portnr=0
1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) foundSOCFPGA_STRATIX10Before "usb start", the registers are:
ffb00000: 00200000 00000000 00000000 00001410 .. .............ffb00010: 80000000 04000021 00000000 00000000 ....!...........ffb00020: 00000000 00002000 20002000 00082000 ..... ... . . ..ffb00030: 00000000 00000000 00000000 12345678 ............xV4.ffb00040:4f54330a00000000238ffc901f8002e8.3TO.......#....ffb00050:fe0f002000000000 000000001f802000............ ..ffb00060: 00000000 00000000 00000000 00000000 ................ffb00070: 00000000 00000000 00000000 00000000 ................ffb00080: 00000000 00000000 00000000 00000000 ................ffb00090: 00000000 00000000 00000000 00000000 ................ffb000a0: 00000000 00000000 00000000 00000000 ................ffb000b0: 00000000 00000000 00000000 00000000 ................ffb000c0: 00000000 00000000 00000000 00000000 ................ffb000d0: 00000000 00000000 00000000 00000000 ................ffb000e0: 00000000 00000000 00000000 00000000 ................ffb000f0: 00000000 00000000 00000000 00000000 ................ffb00100: 20004000 00000000 00000000 00000000 . at . ............ffb00110: 00000000 00000000 00000000 00000000 ................ffb00120: 00000000 00000000 00000000 00000000 ................ffb00130: 00000000 00000000 00000000 00000000 ................ffb00140: 00000000 00000000 00000000 00000000 ................ffb00150: 00000000 00000000 00000000 00000000 ................ffb00160: 00000000 00000000 00000000 00000000 ................ffb00170: 00000000 00000000 00000000 00000000 ................ffb00180: 00000000 00000000 00000000 00000000 ................
ffb00500: 00000000 00000000 00000000 00000000 ................ffb00510: 00000000ffffff7f00000000ffffff7f................ffb00520: 00000000 00000000 00000000 00000000 ................ffb00530: 00000000ffffff7f00002000ffffff7f......... ......ffb00540: 00000000 00000000 00000000 00000000 ................ffb00550: 00000000ffffff7f00002000ffffff7f......... ......ffb00560: 00000000 00000000 00000000 00000000 ................ffb00570: 00000000ffffff7f00002000ffffff7f......... ......ffb00580: 00000000 00000000 00000000 00000000 ................ffb00590: 00000000ffffff7f00002000ffffff7f......... ......ffb005a0: 00000000 00000000 00000000 00000000 ................ffb005b0: 00000000ffffff7f00002000ffffff7f......... ......ffb005c0: 00000000 00000000 00000000 00000000 ................ffb005d0: 00000000ffffff7f00002000ffffff7f......... ......ffb005e0: 00000000 00000000 00000000 00000000 ................ffb005f0: 00000000ffffff7f00002000ffffff7f......... ......ffb00600: 00000000 00000000 00000000 00000000 ................ffb00610: 00000000ffffff7f00002000ffffff7f......... ......ffb00620: 00000000 00000000 00000000 00000000 ................ffb00630: 00000000ffffff7f00002000ffffff7f......... ......ffb00640: 00000000 00000000 00000000 00000000 ................ffb00650: 00000000ffffff7f00002000ffffff7f......... ......ffb00660: 00000000 00000000 00000000 00000000 ................ffb00670: 00000000ffffff7f00002000ffffff7f......... ......ffb00680: 00000000 00000000 00000000 00000000 ................After "usb start":
# md.l 0xffb00000 64 ffb00000: 002e0000 00080000 00000026 01301710 ........&.....0. ffb00010: 80000000 3500002d 00000000 ffffff7f ....-..5........ ffb00020: ffffff7f 00000214 01000214 47080100 ...............G ffb00030: 00000000 00000000 00000000 12345678 ............xV4. ffb00040: 4f54330a 00000000 238ffc90 1f8002e8 .3TO.......#.... ffb00050: fe0f0020 00000000 00000000 1f802000 ............ .. ffb00060: 00000000 00000000 00000000 00000000 ................ ffb00070: 00000000 00000000 00000000 00000000 ................ ffb00080: 00000000 00000000 00000000 00000000 ................ ffb00090: 00000000 00000000 00000000 00000000 ................ ffb000a0: 00000000 00000000 00000000 00000000 ................ ffb000b0: 00000000 00000000 00000000 00000000 ................ ffb000c0: 00000000 00000000 00000000 00000000 ................ ffb000d0: 00000000 00000000 00000000 00000000 ................ ffb000e0: 00000000 00000000 00000000 00000000 ................ ffb000f0: 00000000 00000000 00000000 00000000 ................ ffb00100: 02000314 00000000 00000000 00000000 ................ ffb00110: 00000000 00000000 00000000 00000000 ................ ffb00120: 00000000 00000000 00000000 00000000 ................ ffb00130: 00000000 00000000 00000000 00000000 ................ ffb00140: 00000000 00000000 00000000 00000000 ................ ffb00150: 00000000 00000000 00000000 00000000 ................ ffb00160: 00000000 00000000 00000000 00000000 ................ ffb00170: 00000000 00000000 00000000 00000000 ................ ffb00180: 00000000 00000000 00000000 00000000 ................# md.l 0xffb00500 64 ffb00500: c0100040 00000000 00000000 00000000 @............... ffb00510: 60080008 ffffff7f 00000000 ffffff7f ...`............ ffb00520: c0000000 00000000 00000000 00000000 ................ ffb00530: 00000000 ffffff7f 00000100 ffffff7f ................ ffb00540: c0000000 00000000 00000000 00000000 ................ ffb00550: 00000000 ffffff7f 00000100 ffffff7f ................ ffb00560: c0000000 00000000 00000000 00000000 ................ ffb00570: 00000000 ffffff7f 00000100 ffffff7f ................ ffb00580: c0000000 00000000 00000000 00000000 ................ ffb00590: 00000000 ffffff7f 00000100 ffffff7f ................ ffb005a0: c0000000 00000000 00000000 00000000 ................ ffb005b0: 00000000 ffffff7f 00000100 ffffff7f ................ ffb005c0: c0000000 00000000 00000000 00000000 ................ ffb005d0: 00000000 ffffff7f 00000100 ffffff7f ................ ffb005e0: c0000000 00000000 00000000 00000000 ................ ffb005f0: 00000000 ffffff7f 00000100 ffffff7f ................ ffb00600: c0000000 00000000 00000000 00000000 ................ ffb00610: 00000000 ffffff7f 00000100 ffffff7f ................ ffb00620: c0000000 00000000 00000000 00000000 ................ ffb00630: 00000000 ffffff7f 00000100 ffffff7f ................ ffb00640: c0000000 00000000 00000000 00000000 ................ ffb00650: 00000000 ffffff7f 00000100 ffffff7f ................ ffb00660: c0000000 00000000 00000000 00000000 ................ ffb00670: 00000000 ffffff7f 00000100 ffffff7f ................ ffb00680: c0000000 00000000 00000000 00000000 ................
Quoted 4 lines
I'll follow up the the Linux debug output shortly.
Dinh
Hi,
Can you please apply this patch to Linux kernel driver and check if it help you overcome issue.
drivers/usb/dwc2/hcd.c +0 -0
@@ -2384,10 +2384,12 @@ static void dwc2_core_host_init(struct
dwc2_hsotg *hsotg)
num_channels = hsotg->params.host_channels;
for (i = 0; i < num_channels; i++) {
hcchar = dwc2_readl(hsotg->regs + HCCHAR(i));
- hcchar &= ~HCCHAR_CHENA;
- hcchar |= HCCHAR_CHDIS;
- hcchar &= ~HCCHAR_EPDIR;
- dwc2_writel(hcchar, hsotg->regs + HCCHAR(i));
+ if (hcchar & HCCHAR_CHENA) {
+ hcchar &= ~HCCHAR_CHENA;
+ hcchar |= HCCHAR_CHDIS;
+ hcchar &= ~HCCHAR_EPDIR;
+ dwc2_writel(hcchar, hsotg->regs +
HCCHAR(i));
+ }
}
/* Halt all channels to put them into a known state */
@@ -2395,21 +2397,24 @@ static void dwc2_core_host_init(struct
dwc2_hsotg *hsotg)
int count = 0;
hcchar = dwc2_readl(hsotg->regs + HCCHAR(i));
- hcchar |= HCCHAR_CHENA | HCCHAR_CHDIS;
- hcchar &= ~HCCHAR_EPDIR;
- dwc2_writel(hcchar, hsotg->regs + HCCHAR(i));
- dev_dbg(hsotg->dev, "%s: Halt channel %d\n",- __func__, i);
- do {
- hcchar = dwc2_readl(hsotg->regs +
HCCHAR(i));
- if (++count > 1000) {
- dev_err(hsotg->dev,
- "Unable to clear enable
on channel %d\n",
- i);
- break;
- }
- udelay(1);
- } while (hcchar & HCCHAR_CHENA);
+ if (hcchar & HCCHAR_CHENA) {
+ hcchar |= HCCHAR_CHENA | HCCHAR_CHDIS; + hcchar &= ~HCCHAR_EPDIR; + dwc2_writel(hcchar, hsotg->regs +
HCCHAR(i));
+ dev_dbg(hsotg->dev, "%s: Halt channel %d\n",
+ __func__, i);
+ do {
+ hcchar = dwc2_readl(hsotg->regs +
+ HCCHAR(i));
+ if (++count > 1000) {
+ dev_err(hsotg->dev,
+ "Unable to clear
enable on channel %d\n",
+ i);
+ break;
+ }
+ udelay(1);
+ } while (hcchar & HCCHAR_CHENA);
+ }
}
}Thanks,
Minas