ARM: dts: stm32: Repair AV96 board
Subsystems (2)
v5 cover ARM: dts: stm32: Repair AV96 board
The AV96 board device tree is completely broken and does not match the hardware. This series fixes it up.
Marek Vasut (20):
ARM: dts: stm32: Repair PMIC configuration on AV96
ARM: dts: stm32: Repair PMIC interrupt on AV96
ARM: dts: stm32: Add alternate pinmux for ethernet RGMII
ARM: dts: stm32: Repair ethernet operation on AV96
ARM: dts: stm32: Add missing ethernet PHY reset on AV96
ARM: dts: stm32: Add missing ethernet PHY skews on AV96
ARM: dts: stm32: Add alternate pinmux for SDMMC pins
ARM: dts: stm32: Repair SDMMC1 operation on AV96
ARM: dts: stm32: Add eMMC attached to SDMMC2 on AV96
ARM: dts: stm32: Add QSPI NOR on AV96
ARM: dts: stm32: Add configuration EEPROM on AV96
ARM: dts: stm32: Enable WiFi on AV96
ARM: dts: stm32: Add alternate pinmux for USART2 pins
ARM: dts: stm32: Enable Bluetooth on AV96
ARM: dts: stm32: Add alternate pinmux for LTDC pins
ARM: dts: stm32: Add bindings for HDMI video on AV96
ARM: dts: stm32: Add alternate pinmux for SAI2 pins
ARM: dts: stm32: Add bindings for audio on AV96
ARM: dts: stm32: Add bindings for USB on AV96
ARM: dts: stm32: Rename LEDs to match silkscreen on AV96
arch/arm/boot/dts/stm32mp15-pinctrl.dtsi | 280 +++++++++++++++++ arch/arm/boot/dts/stm32mp157a-avenger96.dts | 324 ++++++++++++++++++-- 2 files changed, 572 insertions(+), 32 deletions(-)
Cc: Alexandre Torgue <[email protected]>
Cc: Manivannan Sadhasivam <[email protected]>
Cc: Maxime Coquelin <[email protected]>
Cc: Patrice Chotard <[email protected]>
Cc: Patrick Delaunay <[email protected]>
Cc: [email protected]
To: [email protected]
Signature · 7 lines
2.25.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v5 1/20 ARM: dts: stm32: Repair PMIC configuration on AV96
The vdd PMIC buck regulator was misconfigured, which caused instability of the board and malfunction of high-speed interfaces, like the RGMII. Configure the PMIC correctly to repair these problems. Also add missing Enpirion regulator for the IO voltage into the DT.
To: [email protected]
---
V2: Model the Enpirion EP53A8LQI on the DHCOR SoM as a fixed regulator
V3: Move this before the SDMMC2 patch, as there is now a dependency
V4: Rebase on stm32-next
V5: Reorder the patch before the SDMMC and ethernet patches
Set buck1 minimum voltage to 1V2
--- arch/arm/boot/dts/stm32mp157a-avenger96.dts | 18 +++++++++++++++--- 1 file changed, 15 insertions(+), 3 deletions(-)
arch/arm/boot/dts/stm32mp157a-avenger96.dts +15 -3
@@ -77,6 +77,17 @@ led6 { default-state = "off"; }; }; + + /* Enpirion EP3A8LQI U2 on the DHCOR */ + vdd_io: regulator-buck-io { + compatible = "regulator-fixed"; + regulator-name = "buck-io"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + vin-supply = <&vdd>; + }; }; ðernet0 {
@@ -166,8 +177,8 @@ vdd_ddr: buck2 { vdd: buck3 { regulator-name = "vdd"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; + regulator-min-microvolt = <2900000>; + regulator-max-microvolt = <2900000>; regulator-always-on; regulator-initial-mode = <0>; regulator-over-current-protection;
@@ -245,6 +256,7 @@ vbus_otg: pwr_sw1 { regulator-name = "vbus_otg"; interrupts = <IT_OCP_OTG 0>; interrupt-parent = <&pmic>; + regulator-active-discharge = <1>; }; vbus_sw: pwr_sw2 {
@@ -275,7 +287,7 @@ &iwdg2 { }; &pwr_regulators { - vdd-supply = <&vdd>; + vdd-supply = <&vdd_io>; vdd_3v3_usbfs-supply = <&vdd_usb>; };
Signature · 7 lines
2.25.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v5 2/20 ARM: dts: stm32: Repair PMIC interrupt on AV96
In reply to Marek VasutThe PMIC interrupt line is connected to PA0 on the DHCOR SoM, fix it. This makes the POWER button on the AV96 working, and also all the other PMIC interrupts. Furthermore, scrub the bogus interrupt-parent props.
To: [email protected]
---
V2: No change
V3: Move this before the SDMMC2 patch
V4: Rebase on stm32-next
V5: Reorder the patch before the SDMMC and ethernet patches
--- arch/arm/boot/dts/stm32mp157a-avenger96.dts | 10 +--------- 1 file changed, 1 insertion(+), 9 deletions(-)
arch/arm/boot/dts/stm32mp157a-avenger96.dts +1 -9
@@ -141,7 +141,7 @@ &i2c4 { pmic: stpmic@33 { compatible = "st,stpmic1"; reg = <0x33>; - interrupts-extended = <&exti 55 IRQ_TYPE_EDGE_FALLING>; + interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>; interrupt-controller; #interrupt-cells = <2>; status = "okay";
@@ -198,7 +198,6 @@ vdda: ldo1 { regulator-min-microvolt = <2900000>; regulator-max-microvolt = <2900000>; interrupts = <IT_CURLIM_LDO1 0>; - interrupt-parent = <&pmic>; }; v2v8: ldo2 {
@@ -206,7 +205,6 @@ v2v8: ldo2 { regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; interrupts = <IT_CURLIM_LDO2 0>; - interrupt-parent = <&pmic>; }; vtt_ddr: ldo3 {
@@ -220,7 +218,6 @@ vtt_ddr: ldo3 { vdd_usb: ldo4 { regulator-name = "vdd_usb"; interrupts = <IT_CURLIM_LDO4 0>; - interrupt-parent = <&pmic>; }; vdd_sd: ldo5 {
@@ -228,7 +225,6 @@ vdd_sd: ldo5 { regulator-min-microvolt = <2900000>; regulator-max-microvolt = <2900000>; interrupts = <IT_CURLIM_LDO5 0>; - interrupt-parent = <&pmic>; regulator-boot-on; };
@@ -237,7 +233,6 @@ v1v8: ldo6 { regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; interrupts = <IT_CURLIM_LDO6 0>; - interrupt-parent = <&pmic>; regulator-enable-ramp-delay = <300000>; };
@@ -249,20 +244,17 @@ vref_ddr: vref_ddr { bst_out: boost { regulator-name = "bst_out"; interrupts = <IT_OCP_BOOST 0>; - interrupt-parent = <&pmic>; }; vbus_otg: pwr_sw1 { regulator-name = "vbus_otg"; interrupts = <IT_OCP_OTG 0>; - interrupt-parent = <&pmic>; regulator-active-discharge = <1>; }; vbus_sw: pwr_sw2 { regulator-name = "vbus_sw"; interrupts = <IT_OCP_SWOUT 0>; - interrupt-parent = <&pmic>; regulator-active-discharge = <1>; }; };
Signature · 7 lines
2.25.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v5 3/20 ARM: dts: stm32: Add alternate pinmux for ethernet RGMII
In reply to Marek VasutAdd another mux option for DWMAC RGMII, this is used on AV96 board.
To: [email protected]
---
V2: No change
V3: No change
V4: Rebase on stm32-next
Rename the pinmux nodes to ethernet0_rgmii_{,sleep_}pins_c
V5: No change
--- arch/arm/boot/dts/stm32mp15-pinctrl.dtsi | 51 ++++++++++++++++++++++++ 1 file changed, 51 insertions(+)
arch/arm/boot/dts/stm32mp15-pinctrl.dtsi +51 -0
@@ -213,6 +213,57 @@ pins1 { }; }; + ethernet0_rgmii_pins_c: rgmii-2 { + pins1 { + pinmux = <STM32_PINMUX('G', 5, AF11)>, /* ETH_RGMII_CLK125 */ + <STM32_PINMUX('G', 4, AF11)>, /* ETH_RGMII_GTX_CLK */ + <STM32_PINMUX('B', 12, AF11)>, /* ETH_RGMII_TXD0 */ + <STM32_PINMUX('G', 14, AF11)>, /* ETH_RGMII_TXD1 */ + <STM32_PINMUX('C', 2, AF11)>, /* ETH_RGMII_TXD2 */ + <STM32_PINMUX('E', 2, AF11)>, /* ETH_RGMII_TXD3 */ + <STM32_PINMUX('G', 11, AF11)>, /* ETH_RGMII_TX_CTL */ + <STM32_PINMUX('C', 1, AF11)>; /* ETH_MDC */ + bias-disable; + drive-push-pull; + slew-rate = <2>; + }; + pins2 { + pinmux = <STM32_PINMUX('A', 2, AF11)>; /* ETH_MDIO */ + bias-disable; + drive-push-pull; + slew-rate = <0>; + }; + pins3 { + pinmux = <STM32_PINMUX('C', 4, AF11)>, /* ETH_RGMII_RXD0 */ + <STM32_PINMUX('C', 5, AF11)>, /* ETH_RGMII_RXD1 */ + <STM32_PINMUX('H', 6, AF11)>, /* ETH_RGMII_RXD2 */ + <STM32_PINMUX('B', 1, AF11)>, /* ETH_RGMII_RXD3 */ + <STM32_PINMUX('A', 1, AF11)>, /* ETH_RGMII_RX_CLK */ + <STM32_PINMUX('A', 7, AF11)>; /* ETH_RGMII_RX_CTL */ + bias-disable; + }; + }; + + ethernet0_rgmii_sleep_pins_c: rgmii-sleep-2 { + pins1 { + pinmux = <STM32_PINMUX('G', 5, ANALOG)>, /* ETH_RGMII_CLK125 */ + <STM32_PINMUX('G', 4, ANALOG)>, /* ETH_RGMII_GTX_CLK */ + <STM32_PINMUX('B', 12, ANALOG)>, /* ETH_RGMII_TXD0 */ + <STM32_PINMUX('G', 14, ANALOG)>, /* ETH_RGMII_TXD1 */ + <STM32_PINMUX('C', 2, ANALOG)>, /* ETH_RGMII_TXD2 */ + <STM32_PINMUX('E', 2, ANALOG)>, /* ETH_RGMII_TXD3 */ + <STM32_PINMUX('G', 11, ANALOG)>, /* ETH_RGMII_TX_CTL */ + <STM32_PINMUX('A', 2, ANALOG)>, /* ETH_MDIO */ + <STM32_PINMUX('C', 1, ANALOG)>, /* ETH_MDC */ + <STM32_PINMUX('C', 4, ANALOG)>, /* ETH_RGMII_RXD0 */ + <STM32_PINMUX('C', 5, ANALOG)>, /* ETH_RGMII_RXD1 */ + <STM32_PINMUX('H', 6, ANALOG)>, /* ETH_RGMII_RXD2 */ + <STM32_PINMUX('B', 1, ANALOG)>, /* ETH_RGMII_RXD3 */ + <STM32_PINMUX('A', 1, ANALOG)>, /* ETH_RGMII_RX_CLK */ + <STM32_PINMUX('A', 7, ANALOG)>; /* ETH_RGMII_RX_CTL */ + }; + }; + ethernet0_rmii_pins_a: rmii-0 { pins1 { pinmux = <STM32_PINMUX('G', 13, AF11)>, /* ETH1_RMII_TXD0 */
Signature · 7 lines
2.25.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v5 4/20 ARM: dts: stm32: Repair ethernet operation on AV96
In reply to Marek VasutThe AV96 RGMII uses different pinmux for ETH_RGMII_TXD0, ETH_RGMII_RXD2 and ETH_RGMII_TX_CTL. Use the correct pinmux to make ethernet operational.
To: [email protected]
---
V2: No change
V3: No change
V4: Rebase on stm32-next
Use renamed pinmux nodes ethernet0_rgmii_{,sleep_}pins_c
V5: No change
--- arch/arm/boot/dts/stm32mp157a-avenger96.dts | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
arch/arm/boot/dts/stm32mp157a-avenger96.dts +2 -2
@@ -92,8 +92,8 @@ vdd_io: regulator-buck-io { ðernet0 { status = "okay"; - pinctrl-0 = <ðernet0_rgmii_pins_a>; - pinctrl-1 = <ðernet0_rgmii_sleep_pins_a>; + pinctrl-0 = <ðernet0_rgmii_pins_c>; + pinctrl-1 = <ðernet0_rgmii_sleep_pins_c>; pinctrl-names = "default", "sleep"; phy-mode = "rgmii"; max-speed = <1000>;
Signature · 7 lines
2.25.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v5 5/20 ARM: dts: stm32: Add missing ethernet PHY reset on AV96
In reply to Marek VasutAdd PHY reset GPIO on AV96 ethernet PHY.
To: [email protected]
---
V2: No change
V3: Drop phy-reset-duration
V4: Rebase on stm32-next
V5: Add reset delay
--- arch/arm/boot/dts/stm32mp157a-avenger96.dts | 3 +++ 1 file changed, 3 insertions(+)
arch/arm/boot/dts/stm32mp157a-avenger96.dts +3 -0
@@ -103,6 +103,9 @@ mdio0 { #address-cells = <1>; #size-cells = <0>; compatible = "snps,dwmac-mdio"; + reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>; + reset-delay-us = <1000>; + phy0: ethernet-phy@7 { reg = <7>; };
Signature · 7 lines
2.25.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v5 6/20 ARM: dts: stm32: Add missing ethernet PHY skews on AV96
In reply to Marek VasutThe KS9031 PHY supports configurable PHY skews to compensate for the board routing. Fill in the correct values.
To: [email protected]
---
V2: No change
V3: No change
V4: Rebase on stm32-next
V5: No change
--- arch/arm/boot/dts/stm32mp157a-avenger96.dts | 14 ++++++++++++++ 1 file changed, 14 insertions(+)
arch/arm/boot/dts/stm32mp157a-avenger96.dts +14 -0
@@ -108,6 +108,20 @@ mdio0 { phy0: ethernet-phy@7 { reg = <7>; + + rxc-skew-ps = <1500>; + rxdv-skew-ps = <540>; + rxd0-skew-ps = <420>; + rxd1-skew-ps = <420>; + rxd2-skew-ps = <420>; + rxd3-skew-ps = <420>; + + txc-skew-ps = <1440>; + txen-skew-ps = <540>; + txd0-skew-ps = <420>; + txd1-skew-ps = <420>; + txd2-skew-ps = <420>; + txd3-skew-ps = <420>; }; }; };
Signature · 7 lines
2.25.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v5 7/20 ARM: dts: stm32: Add alternate pinmux for SDMMC pins
In reply to Marek VasutAdd another mux option for SDMMC1_D123DIR direction pins, SDMMC2 pins 4..7, and SDMMC3 pins PD5_SDMMC3_D2 and PD0_SDMMC3_CMD, this is used on AV96 board.
To: [email protected]
---
V2: Fix SDMMC1_D123DIR AF, should be AF11
V3: No change
V4: Rebase on stm32-next
V5: Squash three patches doing three things into one:
ARM: dts: stm32: Add alternate pinmux for SDMMC1 direction pins
ARM: dts: stm32: Add alternate pinmux for SDMMC2 pins 4-7
ARM: dts: stm32: Add alternate pinmux for SDMMC3 pins
--- arch/arm/boot/dts/stm32mp15-pinctrl.dtsi | 99 ++++++++++++++++++++++++ 1 file changed, 99 insertions(+)
arch/arm/boot/dts/stm32mp15-pinctrl.dtsi +99 -0
@@ -1084,6 +1084,30 @@ pins { }; }; + sdmmc1_dir_pins_b: sdmmc1-dir-1 { + pins1 { + pinmux = <STM32_PINMUX('F', 2, AF11)>, /* SDMMC1_D0DIR */ + <STM32_PINMUX('E', 14, AF11)>, /* SDMMC1_D123DIR */ + <STM32_PINMUX('B', 9, AF11)>; /* SDMMC1_CDIR */ + slew-rate = <1>; + drive-push-pull; + bias-pull-up; + }; + pins2{ + pinmux = <STM32_PINMUX('E', 4, AF8)>; /* SDMMC1_CKIN */ + bias-pull-up; + }; + }; + + sdmmc1_dir_sleep_pins_b: sdmmc1-dir-sleep-1 { + pins { + pinmux = <STM32_PINMUX('F', 2, ANALOG)>, /* SDMMC1_D0DIR */ + <STM32_PINMUX('E', 14, ANALOG)>, /* SDMMC1_D123DIR */ + <STM32_PINMUX('B', 9, ANALOG)>, /* SDMMC1_CDIR */ + <STM32_PINMUX('E', 4, ANALOG)>; /* SDMMC1_CKIN */ + }; + }; + sdmmc2_b4_pins_a: sdmmc2-b4-0 { pins1 { pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC2_D0 */
@@ -1223,6 +1247,27 @@ pins { }; }; + sdmmc2_d47_pins_c: sdmmc2-d47-2 { + pins { + pinmux = <STM32_PINMUX('A', 8, AF9)>, /* SDMMC2_D4 */ + <STM32_PINMUX('A', 15, AF9)>, /* SDMMC2_D5 */ + <STM32_PINMUX('C', 6, AF10)>, /* SDMMC2_D6 */ + <STM32_PINMUX('C', 7, AF10)>; /* SDMMC2_D7 */ + slew-rate = <1>; + drive-push-pull; + bias-pull-up; + }; + }; + + sdmmc2_d47_sleep_pins_c: sdmmc2-d47-sleep-2 { + pins { + pinmux = <STM32_PINMUX('A', 8, ANALOG)>, /* SDMMC2_D4 */ + <STM32_PINMUX('A', 15, ANALOG)>, /* SDMMC2_D5 */ + <STM32_PINMUX('C', 6, ANALOG)>, /* SDMMC2_D6 */ + <STM32_PINMUX('C', 7, ANALOG)>; /* SDMMC2_D7 */ + }; + }; + sdmmc3_b4_pins_a: sdmmc3-b4-0 { pins1 { pinmux = <STM32_PINMUX('F', 0, AF9)>, /* SDMMC3_D0 */
@@ -1277,6 +1322,60 @@ pins { }; }; + sdmmc3_b4_pins_b: sdmmc3-b4-1 { + pins1 { + pinmux = <STM32_PINMUX('F', 0, AF9)>, /* SDMMC3_D0 */ + <STM32_PINMUX('F', 4, AF9)>, /* SDMMC3_D1 */ + <STM32_PINMUX('D', 5, AF10)>, /* SDMMC3_D2 */ + <STM32_PINMUX('D', 7, AF10)>, /* SDMMC3_D3 */ + <STM32_PINMUX('D', 0, AF10)>; /* SDMMC3_CMD */ + slew-rate = <1>; + drive-push-pull; + bias-pull-up; + }; + pins2 { + pinmux = <STM32_PINMUX('G', 15, AF10)>; /* SDMMC3_CK */ + slew-rate = <2>; + drive-push-pull; + bias-pull-up; + }; + }; + + sdmmc3_b4_od_pins_b: sdmmc3-b4-od-1 { + pins1 { + pinmux = <STM32_PINMUX('F', 0, AF9)>, /* SDMMC3_D0 */ + <STM32_PINMUX('F', 4, AF9)>, /* SDMMC3_D1 */ + <STM32_PINMUX('D', 5, AF10)>, /* SDMMC3_D2 */ + <STM32_PINMUX('D', 7, AF10)>; /* SDMMC3_D3 */ + slew-rate = <1>; + drive-push-pull; + bias-pull-up; + }; + pins2 { + pinmux = <STM32_PINMUX('G', 15, AF10)>; /* SDMMC3_CK */ + slew-rate = <2>; + drive-push-pull; + bias-pull-up; + }; + pins3 { + pinmux = <STM32_PINMUX('D', 0, AF10)>; /* SDMMC2_CMD */ + slew-rate = <1>; + drive-open-drain; + bias-pull-up; + }; + }; + + sdmmc3_b4_sleep_pins_b: sdmmc3-b4-sleep-1 { + pins { + pinmux = <STM32_PINMUX('F', 0, ANALOG)>, /* SDMMC3_D0 */ + <STM32_PINMUX('F', 4, ANALOG)>, /* SDMMC3_D1 */ + <STM32_PINMUX('D', 5, ANALOG)>, /* SDMMC3_D2 */ + <STM32_PINMUX('D', 7, ANALOG)>, /* SDMMC3_D3 */ + <STM32_PINMUX('G', 15, ANALOG)>, /* SDMMC3_CK */ + <STM32_PINMUX('D', 0, ANALOG)>; /* SDMMC3_CMD */ + }; + }; + spdifrx_pins_a: spdifrx-0 { pins { pinmux = <STM32_PINMUX('G', 12, AF8)>; /* SPDIF_IN1 */
Signature · 7 lines
2.25.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v5 8/20 ARM: dts: stm32: Repair SDMMC1 operation on AV96
In reply to Marek VasutThe SD uses different pinmux for the D123DIRline, use such a pinmux, otherwise there is a pinmux collision on the AV96. Add missing SD voltage regulator switch.
To: [email protected]
---
V2: Disable SDR104, it seems unstable thus far
V3: No change
V4: Rebase on stm32-next
V5: Reorder this patch after the PMIC patches
--- arch/arm/boot/dts/stm32mp157a-avenger96.dts | 21 ++++++++++++++++++--- 1 file changed, 18 insertions(+), 3 deletions(-)
arch/arm/boot/dts/stm32mp157a-avenger96.dts +18 -3
@@ -78,6 +78,20 @@ led6 { }; }; + sd_switch: regulator-sd_switch { + compatible = "regulator-gpio"; + regulator-name = "sd_switch"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2900000>; + regulator-type = "voltage"; + regulator-always-on; + + gpios = <&gpioi 5 GPIO_ACTIVE_HIGH>; + gpios-states = <0>; + states = <1800000 0x1>, + <2900000 0x0>; + }; + /* Enpirion EP3A8LQI U2 on the DHCOR */ vdd_io: regulator-buck-io { compatible = "regulator-fixed";
@@ -310,9 +324,9 @@ &rtc { &sdmmc1 { pinctrl-names = "default", "opendrain", "sleep"; - pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>; - pinctrl-1 = <&sdmmc1_b4_od_pins_a>; - pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>; + pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_b>; + pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_b>; + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_b>; cd-gpios = <&gpioi 8 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; disable-wp; st,sig-dir;
@@ -320,6 +334,7 @@ &sdmmc1 { st,use-ckin; bus-width = <4>; vmmc-supply = <&vdd_sd>; + vqmmc-supply = <&sd_switch>; status = "okay"; };
Signature · 7 lines
2.25.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v5 9/20 ARM: dts: stm32: Add eMMC attached to SDMMC2 on AV96
In reply to Marek VasutAdd DT node describing the eMMC attached to SDMMC2 controller of the STM32MP1 on DHCOR SoM, which is the SoM soldered on AV96.
To: [email protected]
---
V2: No change
V3: Connect Vcc to the enpirion output instead of 3v3 directly
Note that this patch now depends on:
mmc: mmci: Only call .post_sig_volt_switch if voltage switch happened
V4: Rebase on stm32-next
V5: No change
--- arch/arm/boot/dts/stm32mp157a-avenger96.dts | 16 ++++++++++++++++ 1 file changed, 16 insertions(+)
arch/arm/boot/dts/stm32mp157a-avenger96.dts +16 -0
@@ -338,6 +338,22 @@ &sdmmc1 { status = "okay"; }; +&sdmmc2 { + pinctrl-names = "default", "opendrain", "sleep"; + pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_b>; + pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_b>; + pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_b>; + bus-width = <8>; + mmc-ddr-1_8v; + no-sd; + no-sdio; + non-removable; + st,neg-edge; + vmmc-supply = <&v3v3>; + vqmmc-supply = <&vdd_io>; + status = "okay"; +}; + &uart4 { /* On Low speed expansion header */ label = "LS-UART1";
Signature · 7 lines
2.25.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v5 10/20 ARM: dts: stm32: Add QSPI NOR on AV96
In reply to Marek VasutThe DH Electronics DHCOR SOM has QSPI NOR on the SoM itself, add it into the DT.
To: [email protected]
---
V2: Use spi-flash in the DT node instead of explicit model name
V3: Reduce the SPI controller window to 2 MiB, which is the flash size
V4: Rebase on stm32-next
V5: No change
--- arch/arm/boot/dts/stm32mp157a-avenger96.dts | 20 ++++++++++++++++++++ 1 file changed, 20 insertions(+)
arch/arm/boot/dts/stm32mp157a-avenger96.dts +20 -0
@@ -21,6 +21,7 @@ aliases { mmc0 = &sdmmc1; serial0 = &uart4; serial1 = &uart7; + spi0 = &qspi; }; chosen {
@@ -314,6 +315,25 @@ &pwr_regulators { vdd_3v3_usbfs-supply = <&vdd_usb>; }; +&qspi { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>; + pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a>; + reg = <0x58003000 0x1000>, <0x70000000 0x200000>; + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + flash0: spi-flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-rx-bus-width = <4>; + spi-max-frequency = <108000000>; + #address-cells = <1>; + #size-cells = <1>; + }; +}; + &rng1 { status = "okay"; };
Signature · 7 lines
2.25.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v5 11/20 ARM: dts: stm32: Add configuration EEPROM on AV96
In reply to Marek VasutThe board has an EEPROM on the same I2C bus as PMIC, at address 0x53. The EEPROM contains the board MAC address.
To: [email protected]
---
V2: No change
V3: No change
V4: Rebase on stm32-next
V5: No change
--- arch/arm/boot/dts/stm32mp157a-avenger96.dts | 6 ++++++ 1 file changed, 6 insertions(+)
arch/arm/boot/dts/stm32mp157a-avenger96.dts +6 -0
@@ -303,6 +303,12 @@ watchdog { status = "disabled"; }; }; + + eeprom@53 { + compatible = "atmel,24c02"; + reg = <0x53>; + pagesize = <16>; + }; }; &iwdg2 {
Signature · 7 lines
2.25.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v5 12/20 ARM: dts: stm32: Enable WiFi on AV96
In reply to Marek VasutThe WiFi/Bluetooth SDIO chip is attached to SDMMC3 on AV96, describe it in DT to make it available. Remove WiFi LED and turn it into a regulator, because it is a GPIO controlling the WL_REG_ON input of the WiFi chip. The LED is just an indicator connected to the same line, but not the primary function.
To: [email protected]
---
V2: No change
V3: No change
V4: Rebase on stm32-next
V5: No change
--- arch/arm/boot/dts/stm32mp157a-avenger96.dts | 38 +++++++++++++++++---- 1 file changed, 31 insertions(+), 7 deletions(-)
arch/arm/boot/dts/stm32mp157a-avenger96.dts +31 -7
@@ -65,13 +65,6 @@ led4 { }; led5 { - label = "yellow:wifi"; - gpios = <&gpioz 3 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "phy0tx"; - default-state = "off"; - }; - - led6 { label = "blue:bt"; gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>; linux,default-trigger = "bluetooth-power";
@@ -103,6 +96,17 @@ vdd_io: regulator-buck-io { regulator-boot-on; vin-supply = <&vdd>; }; + + wlan_pwr: regulator-wlan { + compatible = "regulator-fixed"; + + regulator-name = "wl-reg"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpios = <&gpioz 3 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; }; ðernet0 {
@@ -380,6 +384,26 @@ &sdmmc2 { status = "okay"; }; +&sdmmc3 { + pinctrl-names = "default", "opendrain", "sleep"; + pinctrl-0 = <&sdmmc3_b4_pins_b>; + pinctrl-1 = <&sdmmc3_b4_od_pins_b>; + pinctrl-2 = <&sdmmc3_b4_sleep_pins_b>; + broken-cd; + non-removable; + st,neg-edge; + bus-width = <4>; + vmmc-supply = <&wlan_pwr>; + status = "okay"; + + #address-cells = <1>; + #size-cells = <0>; + brcmf: bcrmf@1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + }; +}; + &uart4 { /* On Low speed expansion header */ label = "LS-UART1";
Signature · 7 lines
2.25.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v5 13/20 ARM: dts: stm32: Add alternate pinmux for USART2 pins
In reply to Marek VasutAdd mux option for USART2 pins, this is used on AV96 board.
To: [email protected]
---
V2: No change
V3: No change
V4: Rebase on stm32-next
V5: No change
--- arch/arm/boot/dts/stm32mp15-pinctrl.dtsi | 24 ++++++++++++++++++++++++ 1 file changed, 24 insertions(+)
arch/arm/boot/dts/stm32mp15-pinctrl.dtsi +24 -0
@@ -1389,6 +1389,30 @@ pins { }; }; + usart2_pins_a: usart2-0 { + pins1 { + pinmux = <STM32_PINMUX('F', 5, AF7)>, /* USART2_TX */ + <STM32_PINMUX('D', 4, AF7)>; /* USART2_RTS */ + bias-disable; + drive-push-pull; + slew-rate = <0>; + }; + pins2 { + pinmux = <STM32_PINMUX('D', 6, AF7)>, /* USART2_RX */ + <STM32_PINMUX('D', 3, AF7)>; /* USART2_CTS_NSS */ + bias-disable; + }; + }; + + usart2_sleep_pins_a: usart2-sleep-0 { + pins { + pinmux = <STM32_PINMUX('F', 5, ANALOG)>, /* USART2_TX */ + <STM32_PINMUX('D', 4, ANALOG)>, /* USART2_RTS */ + <STM32_PINMUX('D', 6, ANALOG)>, /* USART2_RX */ + <STM32_PINMUX('D', 3, ANALOG)>; /* USART2_CTS_NSS */ + }; + }; + usart3_pins_a: usart3-0 { pins1 { pinmux = <STM32_PINMUX('B', 10, AF7)>; /* USART3_TX */
Signature · 7 lines
2.25.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v5 14/20 ARM: dts: stm32: Enable Bluetooth on AV96
In reply to Marek VasutThe WiFi/Bluetooth chip is attached to USART2 on AV96 as well, describe it in DT to make it available. Remove BT LED and turn it into a shutdown GPIO, because the GPIO line controls the BT_REG_ON signal. The LED is just an indicator connected to the same line, but not the primary function.
To: [email protected]
---
V2: No change
V3: No change
V4: Rebase on stm32-next
V5: No change
--- arch/arm/boot/dts/stm32mp157a-avenger96.dts | 23 ++++++++++++++------- 1 file changed, 16 insertions(+), 7 deletions(-)
arch/arm/boot/dts/stm32mp157a-avenger96.dts +16 -7
@@ -21,6 +21,7 @@ aliases { mmc0 = &sdmmc1; serial0 = &uart4; serial1 = &uart7; + serial2 = &usart2; spi0 = &qspi; };
@@ -63,13 +64,6 @@ led4 { default-state = "off"; panic-indicator; }; - - led5 { - label = "blue:bt"; - gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "bluetooth-power"; - default-state = "off"; - }; }; sd_switch: regulator-sd_switch {
@@ -419,3 +413,18 @@ &uart7 { pinctrl-0 = <&uart7_pins_a>; status = "okay"; }; + +/* Bluetooth */ +&usart2 { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&usart2_pins_a>; + pinctrl-1 = <&usart2_sleep_pins_a>; + st,hw-flow-ctrl; + status = "okay"; + + bluetooth { + compatible = "brcm,bcm43438-bt"; + max-speed = <3000000>; + shutdown-gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>; + }; +};
Signature · 7 lines
2.25.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v5 15/20 ARM: dts: stm32: Add alternate pinmux for LTDC pins
In reply to Marek VasutAdd new mux option for LTDC pins, this is used on AV96 board.
To: [email protected]
---
V2: No change
V3: No change
V4: - Rebase on stm32-next
- Rename to ltdc.*pins_d
V5: No change
--- arch/arm/boot/dts/stm32mp15-pinctrl.dtsi | 74 ++++++++++++++++++++++++ 1 file changed, 74 insertions(+)
arch/arm/boot/dts/stm32mp15-pinctrl.dtsi +74 -0
@@ -662,6 +662,80 @@ pins1 { }; }; + ltdc_pins_d: ltdc-3 { + pins1 { + pinmux = <STM32_PINMUX('G', 7, AF14)>; /* LCD_CLK */ + bias-disable; + drive-push-pull; + slew-rate = <3>; + }; + pins2 { + pinmux = <STM32_PINMUX('I', 10, AF14)>, /* LCD_HSYNC */ + <STM32_PINMUX('I', 9, AF14)>, /* LCD_VSYNC */ + <STM32_PINMUX('E', 13, AF14)>, /* LCD_DE */ + <STM32_PINMUX('G', 13, AF14)>, /* LCD_R0 */ + <STM32_PINMUX('H', 3, AF14)>, /* LCD_R1 */ + <STM32_PINMUX('H', 8, AF14)>, /* LCD_R2 */ + <STM32_PINMUX('H', 9, AF14)>, /* LCD_R3 */ + <STM32_PINMUX('A', 5, AF14)>, /* LCD_R4 */ + <STM32_PINMUX('H', 11, AF14)>, /* LCD_R5 */ + <STM32_PINMUX('H', 12, AF14)>, /* LCD_R6 */ + <STM32_PINMUX('E', 15, AF14)>, /* LCD_R7 */ + <STM32_PINMUX('E', 5, AF14)>, /* LCD_G0 */ + <STM32_PINMUX('B', 0, AF14)>, /* LCD_G1 */ + <STM32_PINMUX('H', 13, AF14)>, /* LCD_G2 */ + <STM32_PINMUX('E', 11, AF14)>, /* LCD_G3 */ + <STM32_PINMUX('H', 15, AF14)>, /* LCD_G4 */ + <STM32_PINMUX('H', 4, AF9)>, /* LCD_G5 */ + <STM32_PINMUX('I', 11, AF9)>, /* LCD_G6 */ + <STM32_PINMUX('G', 8, AF14)>, /* LCD_G7 */ + <STM32_PINMUX('D', 9, AF14)>, /* LCD_B0 */ + <STM32_PINMUX('G', 12, AF14)>, /* LCD_B1 */ + <STM32_PINMUX('G', 10, AF14)>, /* LCD_B2 */ + <STM32_PINMUX('D', 10, AF14)>, /* LCD_B3 */ + <STM32_PINMUX('E', 12, AF14)>, /* LCD_B4 */ + <STM32_PINMUX('A', 3, AF14)>, /* LCD_B5 */ + <STM32_PINMUX('B', 8, AF14)>, /* LCD_B6 */ + <STM32_PINMUX('I', 7, AF14)>; /* LCD_B7 */ + bias-disable; + drive-push-pull; + slew-rate = <2>; + }; + }; + + ltdc_sleep_pins_d: ltdc-sleep-3 { + pins { + pinmux = <STM32_PINMUX('G', 7, ANALOG)>, /* LCD_CLK */ + <STM32_PINMUX('I', 10, ANALOG)>, /* LCD_HSYNC */ + <STM32_PINMUX('I', 9, ANALOG)>, /* LCD_VSYNC */ + <STM32_PINMUX('E', 13, ANALOG)>, /* LCD_DE */ + <STM32_PINMUX('G', 13, ANALOG)>, /* LCD_R0 */ + <STM32_PINMUX('H', 3, ANALOG)>, /* LCD_R1 */ + <STM32_PINMUX('H', 8, ANALOG)>, /* LCD_R2 */ + <STM32_PINMUX('H', 9, ANALOG)>, /* LCD_R3 */ + <STM32_PINMUX('A', 5, ANALOG)>, /* LCD_R4 */ + <STM32_PINMUX('H', 11, ANALOG)>, /* LCD_R5 */ + <STM32_PINMUX('H', 12, ANALOG)>, /* LCD_R6 */ + <STM32_PINMUX('E', 15, ANALOG)>, /* LCD_R7 */ + <STM32_PINMUX('E', 5, ANALOG)>, /* LCD_G0 */ + <STM32_PINMUX('B', 0, ANALOG)>, /* LCD_G1 */ + <STM32_PINMUX('H', 13, ANALOG)>, /* LCD_G2 */ + <STM32_PINMUX('E', 11, ANALOG)>, /* LCD_G3 */ + <STM32_PINMUX('H', 15, ANALOG)>, /* LCD_G4 */ + <STM32_PINMUX('H', 4, ANALOG)>, /* LCD_G5 */ + <STM32_PINMUX('I', 11, ANALOG)>, /* LCD_G6 */ + <STM32_PINMUX('G', 8, ANALOG)>, /* LCD_G7 */ + <STM32_PINMUX('D', 9, ANALOG)>, /* LCD_B0 */ + <STM32_PINMUX('G', 12, ANALOG)>, /* LCD_B1 */ + <STM32_PINMUX('G', 10, ANALOG)>, /* LCD_B2 */ + <STM32_PINMUX('D', 10, ANALOG)>, /* LCD_B3 */ + <STM32_PINMUX('E', 12, ANALOG)>, /* LCD_B4 */ + <STM32_PINMUX('A', 3, ANALOG)>, /* LCD_B5 */ + <STM32_PINMUX('B', 8, ANALOG)>, /* LCD_B6 */ + <STM32_PINMUX('I', 7, ANALOG)>; /* LCD_B7 */ + }; + }; + m_can1_pins_a: m-can1-0 { pins1 { pinmux = <STM32_PINMUX('H', 13, AF9)>; /* CAN1_TX */
Signature · 7 lines
2.25.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v5 16/20 ARM: dts: stm32: Add bindings for HDMI video on AV96
In reply to Marek VasutFill in the HDMI video pipeline from AV96 into the DT.
To: [email protected]
---
V2: No change
V3: No change
V4: Rebase on stm32-next
Use renamed ltdc_*_pins_d
V5: No change
--- arch/arm/boot/dts/stm32mp157a-avenger96.dts | 79 +++++++++++++++++++++ 1 file changed, 79 insertions(+)
arch/arm/boot/dts/stm32mp157a-avenger96.dts +79 -0
@@ -25,10 +25,28 @@ aliases { spi0 = &qspi; }; + /* XTal Q1 */ + cec_clock: clk-cec-fixed { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <24000000>; + }; + chosen { stdout-path = "serial0:115200n8"; }; + hdmi-out { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con: endpoint { + remote-endpoint = <&adv7513_out>; + }; + }; + }; + memory@c0000000 { device_type = "memory"; reg = <0xc0000000 0x40000000>;
@@ -302,6 +320,50 @@ watchdog { }; }; + hdmi-transmitter@3d { + compatible = "adi,adv7513"; + reg = <0x3d>, <0x2d>, <0x4d>, <0x5d>; + reg-names = "main", "cec", "edid", "packet"; + clocks = <&cec_clock>; + clock-names = "cec"; + + avdd-supply = <&v3v3>; + dvdd-supply = <&v3v3>; + pvdd-supply = <&v3v3>; + dvdd-3v-supply = <&v3v3>; + bgvdd-supply = <&v3v3>; + + interrupts = <9 IRQ_TYPE_EDGE_FALLING>; + interrupt-parent = <&gpiog>; + + status = "okay"; + + adi,input-depth = <8>; + adi,input-colorspace = "rgb"; + adi,input-clock = "1x"; + adi,input-style = <1>; + adi,input-justification = "evenly"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + adv7513_in: endpoint { + remote-endpoint = <<dc_ep0_out>; + }; + }; + + port@1 { + reg = <1>; + adv7513_out: endpoint { + remote-endpoint = <&hdmi_con>; + }; + }; + }; + }; + eeprom@53 { compatible = "atmel,24c02"; reg = <0x53>;
@@ -314,6 +376,23 @@ &iwdg2 { status = "okay"; }; +<dc { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <<dc_pins_d>; + pinctrl-1 = <<dc_sleep_pins_d>; + status = "okay"; + + port { + #address-cells = <1>; + #size-cells = <0>; + + ltdc_ep0_out: endpoint@0 { + reg = <0>; + remote-endpoint = <&adv7513_in>; + }; + }; +}; + &pwr_regulators { vdd-supply = <&vdd_io>; vdd_3v3_usbfs-supply = <&vdd_usb>;
Signature · 7 lines
2.25.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v5 17/20 ARM: dts: stm32: Add alternate pinmux for SAI2 pins
In reply to Marek VasutAdd new mux option for SAI2 pins, this is used on AV96 board.
To: [email protected]
---
V4: New patch
V5: No change
--- arch/arm/boot/dts/stm32mp15-pinctrl.dtsi | 32 ++++++++++++++++++++++++ 1 file changed, 32 insertions(+)
arch/arm/boot/dts/stm32mp15-pinctrl.dtsi +32 -0
@@ -1028,6 +1028,25 @@ pins { }; }; + sai2a_pins_c: sai2a-4 { + pins { + pinmux = <STM32_PINMUX('D', 13, AF10)>, /* SAI2_SCK_A */ + <STM32_PINMUX('D', 11, AF10)>, /* SAI2_SD_A */ + <STM32_PINMUX('D', 12, AF10)>; /* SAI2_FS_A */ + slew-rate = <0>; + drive-push-pull; + bias-disable; + }; + }; + + sai2a_sleep_pins_c: sai2a-5 { + pins { + pinmux = <STM32_PINMUX('D', 13, ANALOG)>, /* SAI2_SCK_A */ + <STM32_PINMUX('D', 11, ANALOG)>, /* SAI2_SD_A */ + <STM32_PINMUX('D', 12, ANALOG)>; /* SAI2_FS_A */ + }; + }; + sai2b_pins_a: sai2b-0 { pins1 { pinmux = <STM32_PINMUX('E', 12, AF10)>, /* SAI2_SCK_B */
@@ -1065,6 +1084,19 @@ pins { }; }; + sai2b_pins_c: sai2a-4 { + pins1 { + pinmux = <STM32_PINMUX('F', 11, AF10)>; /* SAI2_SD_B */ + bias-disable; + }; + }; + + sai2b_sleep_pins_c: sai2a-sleep-5 { + pins { + pinmux = <STM32_PINMUX('F', 11, ANALOG)>; /* SAI2_SD_B */ + }; + }; + sai4a_pins_a: sai4a-0 { pins { pinmux = <STM32_PINMUX('B', 5, AF10)>; /* SAI4_SD_A */
Signature · 7 lines
2.25.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v5 18/20 ARM: dts: stm32: Add bindings for audio on AV96
In reply to Marek VasutFill in the bindings for HDMI audio on AV96, this permits audio playback via attached HDMI device if such device supports it.
To: [email protected]
---
V2: No change
V3: No change
V4: No change
V5: No change
--- arch/arm/boot/dts/stm32mp157a-avenger96.dts | 39 +++++++++++++++++++++ 1 file changed, 39 insertions(+)
arch/arm/boot/dts/stm32mp157a-avenger96.dts +39 -0
@@ -98,6 +98,13 @@ sd_switch: regulator-sd_switch { <2900000 0x0>; }; + sound { + compatible = "audio-graph-card"; + label = "STM32MP1-AV96-HDMI"; + dais = <&sai2a_port>; + status = "okay"; + }; + /* Enpirion EP3A8LQI U2 on the DHCOR */ vdd_io: regulator-buck-io { compatible = "regulator-fixed";
@@ -361,6 +368,13 @@ adv7513_out: endpoint { remote-endpoint = <&hdmi_con>; }; }; + + port@2 { + reg = <2>; + adv7513_i2s0: endpoint { + remote-endpoint = <&sai2a_endpoint>; + }; + }; }; };
@@ -425,6 +439,31 @@ &rtc { status = "okay"; }; +&sai2 { + clocks = <&rcc SAI2>, <&rcc PLL3_Q>, <&rcc PLL3_R>; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sai2a_pins_c>; + pinctrl-1 = <&sai2a_sleep_pins_c>; + clock-names = "pclk", "x8k", "x11k"; + status = "okay"; + + sai2a: audio-controller@4400b004 { + #clock-cells = <0>; + dma-names = "tx"; + clocks = <&rcc SAI2_K>; + clock-names = "sai_ck"; + status = "okay"; + + sai2a_port: port { + sai2a_endpoint: endpoint { + remote-endpoint = <&adv7513_i2s0>; + format = "i2s"; + mclk-fs = <256>; + }; + }; + }; +}; + &sdmmc1 { pinctrl-names = "default", "opendrain", "sleep"; pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_b>;
Signature · 7 lines
2.25.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v5 19/20 ARM: dts: stm32: Add bindings for USB on AV96
In reply to Marek VasutFill in the bindings for USB host and gadget on AV96.
To: [email protected]
---
V2: No change
V3: No change
V4: No change
V5: No change
--- arch/arm/boot/dts/stm32mp157a-avenger96.dts | 31 +++++++++++++++++++++ 1 file changed, 31 insertions(+)
arch/arm/boot/dts/stm32mp157a-avenger96.dts +31 -0
@@ -546,3 +546,34 @@ bluetooth { shutdown-gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>; }; }; + +&usbh_ehci { + phys = <&usbphyc_port0>; + phy-names = "usb"; + status = "okay"; +}; + +&usbotg_hs { + pinctrl-0 = <&usbotg_hs_pins_a>; + pinctrl-names = "default"; + phy-names = "usb2-phy"; + phys = <&usbphyc_port1 0>; + status = "okay"; + vbus-supply = <&vbus_otg>; +}; + +&usbphyc { + status = "okay"; +}; + +&usbphyc_port0 { + phy-supply = <&vdd_usb>; + vdda1v1-supply = <®11>; + vdda1v8-supply = <®18>; +}; + +&usbphyc_port1 { + phy-supply = <&vdd_usb>; + vdda1v1-supply = <®11>; + vdda1v8-supply = <®18>; +};
Signature · 7 lines
2.25.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v5 20/20 ARM: dts: stm32: Rename LEDs to match silkscreen on AV96
In reply to Marek VasutThe LED labels do not match the silkscreen on the board, fix it.
To: [email protected]
---
V2: No change
V3: No change
V4: No change
V5: No change
--- arch/arm/boot/dts/stm32mp157a-avenger96.dts | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-)
arch/arm/boot/dts/stm32mp157a-avenger96.dts +3 -3
@@ -55,21 +55,21 @@ memory@c0000000 { led { compatible = "gpio-leds"; led1 { - label = "green:user1"; + label = "green:user0"; gpios = <&gpioz 7 GPIO_ACTIVE_HIGH>; linux,default-trigger = "heartbeat"; default-state = "off"; }; led2 { - label = "green:user2"; + label = "green:user1"; gpios = <&gpiof 3 GPIO_ACTIVE_HIGH>; linux,default-trigger = "mmc0"; default-state = "off"; }; led3 { - label = "green:user3"; + label = "green:user2"; gpios = <&gpiog 0 GPIO_ACTIVE_HIGH>; linux,default-trigger = "mmc1"; default-state = "off";
Signature · 7 lines
2.25.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Ki Marek
Quoted 29 lines · Marek Vasut
The AV96 board device tree is completely broken and does not match the hardware. This series fixes it up.
Marek Vasut (20):
ARM: dts: stm32: Repair PMIC configuration on AV96
ARM: dts: stm32: Repair PMIC interrupt on AV96
ARM: dts: stm32: Add alternate pinmux for ethernet RGMII
ARM: dts: stm32: Repair ethernet operation on AV96
ARM: dts: stm32: Add missing ethernet PHY reset on AV96
ARM: dts: stm32: Add missing ethernet PHY skews on AV96
ARM: dts: stm32: Add alternate pinmux for SDMMC pins
ARM: dts: stm32: Repair SDMMC1 operation on AV96
ARM: dts: stm32: Add eMMC attached to SDMMC2 on AV96
ARM: dts: stm32: Add QSPI NOR on AV96
ARM: dts: stm32: Add configuration EEPROM on AV96
ARM: dts: stm32: Enable WiFi on AV96
ARM: dts: stm32: Add alternate pinmux for USART2 pins
ARM: dts: stm32: Enable Bluetooth on AV96
ARM: dts: stm32: Add alternate pinmux for LTDC pins
ARM: dts: stm32: Add bindings for HDMI video on AV96
ARM: dts: stm32: Add alternate pinmux for SAI2 pins
ARM: dts: stm32: Add bindings for audio on AV96
ARM: dts: stm32: Add bindings for USB on AV96
ARM: dts: stm32: Rename LEDs to match silkscreen on AV96arch/arm/boot/dts/stm32mp15-pinctrl.dtsi | 280 +++++++++++++++++ arch/arm/boot/dts/stm32mp157a-avenger96.dts | 324 ++++++++++++++++++-- 2 files changed, 572 insertions(+), 32 deletions(-)
Quoted 8 lines
Cc: Alexandre Torgue <[email protected]>
Cc: Manivannan Sadhasivam <[email protected]>
Cc: Maxime Coquelin <[email protected]>
Cc: Patrice Chotard <[email protected]>
Cc: Patrick Delaunay <[email protected]>
Cc: [email protected]
To: [email protected]
Series looks good to me. I'll merge it for my next Pr.
Just one question, Are we still able to boot older board revision (prototype ones)?
regards
alex
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Quoted 1 line · Alexandre Torgue
Ki Marek
Hi,
Quoted 39 lines · Marek Vasut
Quoted 29 lines
The AV96 board device tree is completely broken and does not match the hardware. This series fixes it up.
Marek Vasut (20):
ARM: dts: stm32: Repair PMIC configuration on AV96
ARM: dts: stm32: Repair PMIC interrupt on AV96
ARM: dts: stm32: Add alternate pinmux for ethernet RGMII
ARM: dts: stm32: Repair ethernet operation on AV96
ARM: dts: stm32: Add missing ethernet PHY reset on AV96
ARM: dts: stm32: Add missing ethernet PHY skews on AV96
ARM: dts: stm32: Add alternate pinmux for SDMMC pins
ARM: dts: stm32: Repair SDMMC1 operation on AV96
ARM: dts: stm32: Add eMMC attached to SDMMC2 on AV96
ARM: dts: stm32: Add QSPI NOR on AV96
ARM: dts: stm32: Add configuration EEPROM on AV96
ARM: dts: stm32: Enable WiFi on AV96
ARM: dts: stm32: Add alternate pinmux for USART2 pins
ARM: dts: stm32: Enable Bluetooth on AV96
ARM: dts: stm32: Add alternate pinmux for LTDC pins
ARM: dts: stm32: Add bindings for HDMI video on AV96
ARM: dts: stm32: Add alternate pinmux for SAI2 pins
ARM: dts: stm32: Add bindings for audio on AV96
ARM: dts: stm32: Add bindings for USB on AV96
ARM: dts: stm32: Rename LEDs to match silkscreen on AV96arch/arm/boot/dts/stm32mp15-pinctrl.dtsi | 280 +++++++++++++++++
arch/arm/boot/dts/stm32mp157a-avenger96.dts| 324 ++++++++++++++++++--2 files changed, 572 insertions(+), 32 deletions(-)Quoted 8 lines
Cc: Alexandre Torgue <[email protected]>
Cc: Manivannan Sadhasivam <[email protected]>
Cc: Maxime Coquelin <[email protected]>
Cc: Patrice Chotard <[email protected]>
Cc: Patrick Delaunay <[email protected]>
Cc: [email protected]
To: [email protected]
Quoted 3 lines
Series looks good to me. I'll merge it for my next Pr. Just one question, Are we still able to boot older board revision (prototype ones)?
I don't have one, but if we want to support the prototypes, we will need a separate DT for that (or a few DTSi to handle the HW differences).
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Quoted 4 lines · Marek Vasut
Quoted 1 line · Alexandre Torgue
Ki Marek
Hi,
Hello again,
Quoted 39 lines
Quoted 39 lines · Marek Vasut
Quoted 37 lines
The AV96 board device tree is completely broken and does not match the hardware. This series fixes it up.
Marek Vasut (20):
ARM: dts: stm32: Repair PMIC configuration on AV96
ARM: dts: stm32: Repair PMIC interrupt on AV96
ARM: dts: stm32: Add alternate pinmux for ethernet RGMII
ARM: dts: stm32: Repair ethernet operation on AV96
ARM: dts: stm32: Add missing ethernet PHY reset on AV96
ARM: dts: stm32: Add missing ethernet PHY skews on AV96
ARM: dts: stm32: Add alternate pinmux for SDMMC pins
ARM: dts: stm32: Repair SDMMC1 operation on AV96
ARM: dts: stm32: Add eMMC attached to SDMMC2 on AV96
ARM: dts: stm32: Add QSPI NOR on AV96
ARM: dts: stm32: Add configuration EEPROM on AV96
ARM: dts: stm32: Enable WiFi on AV96
ARM: dts: stm32: Add alternate pinmux for USART2 pins
ARM: dts: stm32: Enable Bluetooth on AV96
ARM: dts: stm32: Add alternate pinmux for LTDC pins
ARM: dts: stm32: Add bindings for HDMI video on AV96
ARM: dts: stm32: Add alternate pinmux for SAI2 pins
ARM: dts: stm32: Add bindings for audio on AV96
ARM: dts: stm32: Add bindings for USB on AV96
ARM: dts: stm32: Rename LEDs to match silkscreen on AV96arch/arm/boot/dts/stm32mp15-pinctrl.dtsi | 280 +++++++++++++++++
arch/arm/boot/dts/stm32mp157a-avenger96.dts| 324 ++++++++++++++++++--2 files changed, 572 insertions(+), 32 deletions(-)Cc: Alexandre Torgue <[email protected]>
Cc: Manivannan Sadhasivam <[email protected]>
Cc: Maxime Coquelin <[email protected]>
Cc: Patrice Chotard <[email protected]>
Cc: Patrick Delaunay <[email protected]>
Cc: [email protected]
To: [email protected]
Quoted 6 lines
Quoted 3 lines
Series looks good to me. I'll merge it for my next Pr. Just one question, Are we still able to boot older board revision (prototype ones)?
I don't have one, but if we want to support the prototypes, we will need a separate DT for that (or a few DTSi to handle the HW differences).
I got the 588-100 prototype too now, and I have more patches which I would like to start upstreaming on top of this series (like split the SoM DT from the board DT), can these be applied so I can start sending the rest?
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Hi Marek
Quoted 51 lines · Marek Vasut
Quoted 4 lines · Marek Vasut
Quoted 1 line · Alexandre Torgue
Ki Marek
Hi,
Hello again,
Quoted 43 lines
Quoted 42 lines · Marek Vasut
Quoted 29 lines
The AV96 board device tree is completely broken and does not match the hardware. This series fixes it up.
Marek Vasut (20):
ARM: dts: stm32: Repair PMIC configuration on AV96
ARM: dts: stm32: Repair PMIC interrupt on AV96
ARM: dts: stm32: Add alternate pinmux for ethernet RGMII
ARM: dts: stm32: Repair ethernet operation on AV96
ARM: dts: stm32: Add missing ethernet PHY reset on AV96
ARM: dts: stm32: Add missing ethernet PHY skews on AV96
ARM: dts: stm32: Add alternate pinmux for SDMMC pins
ARM: dts: stm32: Repair SDMMC1 operation on AV96
ARM: dts: stm32: Add eMMC attached to SDMMC2 on AV96
ARM: dts: stm32: Add QSPI NOR on AV96
ARM: dts: stm32: Add configuration EEPROM on AV96
ARM: dts: stm32: Enable WiFi on AV96
ARM: dts: stm32: Add alternate pinmux for USART2 pins
ARM: dts: stm32: Enable Bluetooth on AV96
ARM: dts: stm32: Add alternate pinmux for LTDC pins
ARM: dts: stm32: Add bindings for HDMI video on AV96
ARM: dts: stm32: Add alternate pinmux for SAI2 pins
ARM: dts: stm32: Add bindings for audio on AV96
ARM: dts: stm32: Add bindings for USB on AV96
ARM: dts: stm32: Rename LEDs to match silkscreen on AV96arch/arm/boot/dts/stm32mp15-pinctrl.dtsi | 280 +++++++++++++++++ arch/arm/boot/dts/stm32mp157a-avenger96.dts | 324 ++++++++++++++++++-- 2 files changed, 572 insertions(+), 32 deletions(-)Quoted 8 lines
Cc: Alexandre Torgue <[email protected]>
Cc: Manivannan Sadhasivam <[email protected]>
Cc: Maxime Coquelin <[email protected]>
Cc: Patrice Chotard <[email protected]>
Cc: Patrick Delaunay <[email protected]>
Cc: [email protected]
To: [email protected]Series looks good to me. I'll merge it for my next Pr. Just one question, Are we still able to boot older board revision (prototype ones)?
Quoted 8 lines
Quoted 2 lines
I don't have one, but if we want to support the prototypes, we will need a separate DT for that (or a few DTSi to handle the HW differences).
I got the 588-100 prototype too now, and I have more patches which I would like to start upstreaming on top of this series (like split the SoM DT from the board DT), can these be applied so I can start sending the rest?
I'll try to do it today or tomorrow.
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Quoted 58 lines · Alexandre Torgue
Hi Marek
Quoted 55 lines · Marek Vasut
Quoted 4 lines · Marek Vasut
Quoted 1 line · Alexandre Torgue
Ki Marek
Hi,
Hello again,
Quoted 46 lines
Quoted 40 lines · Marek Vasut
Quoted 30 lines
The AV96 board device tree is completely broken and does not match the hardware. This series fixes it up.
Marek Vasut (20):
ARM: dts: stm32: Repair PMIC configuration on AV96
ARM: dts: stm32: Repair PMIC interrupt on AV96
ARM: dts: stm32: Add alternate pinmux for ethernet RGMII
ARM: dts: stm32: Repair ethernet operation on AV96
ARM: dts: stm32: Add missing ethernet PHY reset on AV96
ARM: dts: stm32: Add missing ethernet PHY skews on AV96
ARM: dts: stm32: Add alternate pinmux for SDMMC pins
ARM: dts: stm32: Repair SDMMC1 operation on AV96
ARM: dts: stm32: Add eMMC attached to SDMMC2 on AV96
ARM: dts: stm32: Add QSPI NOR on AV96
ARM: dts: stm32: Add configuration EEPROM on AV96
ARM: dts: stm32: Enable WiFi on AV96
ARM: dts: stm32: Add alternate pinmux for USART2 pins
ARM: dts: stm32: Enable Bluetooth on AV96
ARM: dts: stm32: Add alternate pinmux for LTDC pins
ARM: dts: stm32: Add bindings for HDMI video on AV96
ARM: dts: stm32: Add alternate pinmux for SAI2 pins
ARM: dts: stm32: Add bindings for audio on AV96
ARM: dts: stm32: Add bindings for USB on AV96
ARM: dts: stm32: Rename LEDs to match silkscreen on AV96arch/arm/boot/dts/stm32mp15-pinctrl.dtsi | 280 +++++++++++++++++
arch/arm/boot/dts/stm32mp157a-avenger96.dts| 324
++++++++++++++++++--2 files changed, 572 insertions(+), 32 deletions(-)Quoted 8 lines
Cc: Alexandre Torgue <[email protected]>
Cc: Manivannan Sadhasivam <[email protected]>
Cc: Maxime Coquelin <[email protected]>
Cc: Patrice Chotard <[email protected]>
Cc: Patrick Delaunay <[email protected]>
Cc: [email protected]
To: [email protected]Quoted 3 lines
Series looks good to me. I'll merge it for my next Pr. Just one question, Are we still able to boot older board revision (prototype ones)?
I don't have one, but if we want to support the prototypes, we will need a separate DT for that (or a few DTSi to handle the HW differences).
Quoted 7 lines
Quoted 5 lines
I got the 588-100 prototype too now, and I have more patches which I would like to start upstreaming on top of this series (like split the SoM DT from the board DT), can these be applied so I can start sending the rest?
I'll try to do it today or tomorrow.
Cool, thanks !
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Hi Marek
Quoted 29 lines · Marek Vasut
The AV96 board device tree is completely broken and does not match the hardware. This series fixes it up.
Marek Vasut (20):
ARM: dts: stm32: Repair PMIC configuration on AV96
ARM: dts: stm32: Repair PMIC interrupt on AV96
ARM: dts: stm32: Add alternate pinmux for ethernet RGMII
ARM: dts: stm32: Repair ethernet operation on AV96
ARM: dts: stm32: Add missing ethernet PHY reset on AV96
ARM: dts: stm32: Add missing ethernet PHY skews on AV96
ARM: dts: stm32: Add alternate pinmux for SDMMC pins
ARM: dts: stm32: Repair SDMMC1 operation on AV96
ARM: dts: stm32: Add eMMC attached to SDMMC2 on AV96
ARM: dts: stm32: Add QSPI NOR on AV96
ARM: dts: stm32: Add configuration EEPROM on AV96
ARM: dts: stm32: Enable WiFi on AV96
ARM: dts: stm32: Add alternate pinmux for USART2 pins
ARM: dts: stm32: Enable Bluetooth on AV96
ARM: dts: stm32: Add alternate pinmux for LTDC pins
ARM: dts: stm32: Add bindings for HDMI video on AV96
ARM: dts: stm32: Add alternate pinmux for SAI2 pins
ARM: dts: stm32: Add bindings for audio on AV96
ARM: dts: stm32: Add bindings for USB on AV96
ARM: dts: stm32: Rename LEDs to match silkscreen on AV96arch/arm/boot/dts/stm32mp15-pinctrl.dtsi | 280 +++++++++++++++++ arch/arm/boot/dts/stm32mp157a-avenger96.dts | 324 ++++++++++++++++++-- 2 files changed, 572 insertions(+), 32 deletions(-)
Quoted 8 lines
Cc: Alexandre Torgue <[email protected]>
Cc: Manivannan Sadhasivam <[email protected]>
Cc: Maxime Coquelin <[email protected]>
Cc: Patrice Chotard <[email protected]>
Cc: Patrick Delaunay <[email protected]>
Cc: [email protected]
To: [email protected]
Series applied on stm32-next.
Thanks
Alex
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Quoted 41 lines · Alexandre Torgue
Hi Marek
Quoted 29 lines · Marek Vasut
The AV96 board device tree is completely broken and does not match the hardware. This series fixes it up.
Marek Vasut (20):
ARM: dts: stm32: Repair PMIC configuration on AV96
ARM: dts: stm32: Repair PMIC interrupt on AV96
ARM: dts: stm32: Add alternate pinmux for ethernet RGMII
ARM: dts: stm32: Repair ethernet operation on AV96
ARM: dts: stm32: Add missing ethernet PHY reset on AV96
ARM: dts: stm32: Add missing ethernet PHY skews on AV96
ARM: dts: stm32: Add alternate pinmux for SDMMC pins
ARM: dts: stm32: Repair SDMMC1 operation on AV96
ARM: dts: stm32: Add eMMC attached to SDMMC2 on AV96
ARM: dts: stm32: Add QSPI NOR on AV96
ARM: dts: stm32: Add configuration EEPROM on AV96
ARM: dts: stm32: Enable WiFi on AV96
ARM: dts: stm32: Add alternate pinmux for USART2 pins
ARM: dts: stm32: Enable Bluetooth on AV96
ARM: dts: stm32: Add alternate pinmux for LTDC pins
ARM: dts: stm32: Add bindings for HDMI video on AV96
ARM: dts: stm32: Add alternate pinmux for SAI2 pins
ARM: dts: stm32: Add bindings for audio on AV96
ARM: dts: stm32: Add bindings for USB on AV96
ARM: dts: stm32: Rename LEDs to match silkscreen on AV96arch/arm/boot/dts/stm32mp15-pinctrl.dtsi | 280 +++++++++++++++++
arch/arm/boot/dts/stm32mp157a-avenger96.dts| 324 ++++++++++++++++++--2 files changed, 572 insertions(+), 32 deletions(-)Quoted 8 lines
Cc: Alexandre Torgue <[email protected]>
Cc: Manivannan Sadhasivam <[email protected]>
Cc: Maxime Coquelin <[email protected]>
Cc: Patrice Chotard <[email protected]>
Cc: Patrick Delaunay <[email protected]>
Cc: [email protected]
To: [email protected]
Quoted 1 line
Series applied on stm32-next.
Thanks. I sent out the rest, which should be very much all there is for now :)
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Quoted 42 lines · Marek Vasut
Quoted 41 lines · Alexandre Torgue
Hi Marek
Quoted 37 lines · Marek Vasut
The AV96 board device tree is completely broken and does not match the hardware. This series fixes it up.
Marek Vasut (20):
ARM: dts: stm32: Repair PMIC configuration on AV96
ARM: dts: stm32: Repair PMIC interrupt on AV96
ARM: dts: stm32: Add alternate pinmux for ethernet RGMII
ARM: dts: stm32: Repair ethernet operation on AV96
ARM: dts: stm32: Add missing ethernet PHY reset on AV96
ARM: dts: stm32: Add missing ethernet PHY skews on AV96
ARM: dts: stm32: Add alternate pinmux for SDMMC pins
ARM: dts: stm32: Repair SDMMC1 operation on AV96
ARM: dts: stm32: Add eMMC attached to SDMMC2 on AV96
ARM: dts: stm32: Add QSPI NOR on AV96
ARM: dts: stm32: Add configuration EEPROM on AV96
ARM: dts: stm32: Enable WiFi on AV96
ARM: dts: stm32: Add alternate pinmux for USART2 pins
ARM: dts: stm32: Enable Bluetooth on AV96
ARM: dts: stm32: Add alternate pinmux for LTDC pins
ARM: dts: stm32: Add bindings for HDMI video on AV96
ARM: dts: stm32: Add alternate pinmux for SAI2 pins
ARM: dts: stm32: Add bindings for audio on AV96
ARM: dts: stm32: Add bindings for USB on AV96
ARM: dts: stm32: Rename LEDs to match silkscreen on AV96arch/arm/boot/dts/stm32mp15-pinctrl.dtsi | 280 +++++++++++++++++ arch/arm/boot/dts/stm32mp157a-avenger96.dts | 324 ++++++++++++++++++-- 2 files changed, 572 insertions(+), 32 deletions(-)Cc: Alexandre Torgue <[email protected]>
Cc: Manivannan Sadhasivam <[email protected]>
Cc: Maxime Coquelin <[email protected]>
Cc: Patrice Chotard <[email protected]>
Cc: Patrick Delaunay <[email protected]>
Cc: [email protected]
To: [email protected]
Quoted 4 lines
Quoted 1 line
Series applied on stm32-next.
Thanks. I sent out the rest, which should be very much all there is for now :) >
I hope :). I had a look on it and it sounds good. I'll merge it next week.
regards
alex
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Quoted 46 lines · Alexandre Torgue
Quoted 43 lines · Marek Vasut
Quoted 42 lines · Alexandre Torgue
Hi Marek
Quoted 38 lines · Marek Vasut
The AV96 board device tree is completely broken and does not match the hardware. This series fixes it up.
Marek Vasut (20):
ARM: dts: stm32: Repair PMIC configuration on AV96
ARM: dts: stm32: Repair PMIC interrupt on AV96
ARM: dts: stm32: Add alternate pinmux for ethernet RGMII
ARM: dts: stm32: Repair ethernet operation on AV96
ARM: dts: stm32: Add missing ethernet PHY reset on AV96
ARM: dts: stm32: Add missing ethernet PHY skews on AV96
ARM: dts: stm32: Add alternate pinmux for SDMMC pins
ARM: dts: stm32: Repair SDMMC1 operation on AV96
ARM: dts: stm32: Add eMMC attached to SDMMC2 on AV96
ARM: dts: stm32: Add QSPI NOR on AV96
ARM: dts: stm32: Add configuration EEPROM on AV96
ARM: dts: stm32: Enable WiFi on AV96
ARM: dts: stm32: Add alternate pinmux for USART2 pins
ARM: dts: stm32: Enable Bluetooth on AV96
ARM: dts: stm32: Add alternate pinmux for LTDC pins
ARM: dts: stm32: Add bindings for HDMI video on AV96
ARM: dts: stm32: Add alternate pinmux for SAI2 pins
ARM: dts: stm32: Add bindings for audio on AV96
ARM: dts: stm32: Add bindings for USB on AV96
ARM: dts: stm32: Rename LEDs to match silkscreen on AV96arch/arm/boot/dts/stm32mp15-pinctrl.dtsi | 280 +++++++++++++++++
arch/arm/boot/dts/stm32mp157a-avenger96.dts| 324
++++++++++++++++++--2 files changed, 572 insertions(+), 32 deletions(-)Cc: Alexandre Torgue <[email protected]>
Cc: Manivannan Sadhasivam <[email protected]>
Cc: Maxime Coquelin <[email protected]>
Cc: Patrice Chotard <[email protected]>
Cc: Patrick Delaunay <[email protected]>
Cc: [email protected]
To: [email protected]
Quoted 6 lines
Quoted 4 lines
Quoted 1 line
Series applied on stm32-next.
Thanks. I sent out the rest, which should be very much all there is for now :) >
I hope :). I had a look on it and it sounds good. I'll merge it next week.
Nice, thanks.
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel