reset: socfpga: add an early reset driver for SoCFPGA
Subsystems (4)
Dinh Nguyen
maintainerPATCH v4 1/1 reset: socfpga: add an early reset driver for SoCFPGA
Create a separate reset driver that uses the reset operations in reset-simple. The reset driver for the SoCFPGA platform needs to register early in order to be able bring online timers that needed early in the kernel bootup.
We do not need this early reset driver for Stratix10, because on arm64, Linux does not need the timers are that in reset. Linux is able to run just fine with the internal armv8 timer. Thus, we use a new binding "altr,stratix10-rst-mgr" for the Stratix10 platform. The Stratix10 platform will continue to use the reset-simple platform driver, while the 32-bit platforms(Cyclone5/Arria5/Arria10) will use the early reset driver.
---
v4: remove !ARCH_STRATIX10 condition in Kconfig
clean up checkpatch.pl errors
v3: use "altr,stratix10-rst-mgr" for Stratix10
remove "altr,modrst-offset" from reset-simple
v2: Do not build separate reset driver for STRATIX10
fix warning: symbol 'socfpga_reset_init' was not declared. Should it be static?
--- arch/arm/mach-socfpga/socfpga.c | 4 ++ drivers/reset/Kconfig | 10 +++- drivers/reset/Makefile | 1 + drivers/reset/reset-simple.c | 13 ++--- drivers/reset/reset-socfpga.c | 88 +++++++++++++++++++++++++++++++++ 5 files changed, 105 insertions(+), 11 deletions(-) create mode 100644 drivers/reset/reset-socfpga.c
arch/arm/mach-socfpga/socfpga.c +4 -0
@@ -32,6 +32,8 @@ void __iomem *rst_manager_base_addr;void __iomem *sdr_ctl_base_addr;unsigned long socfpga_cpu1start_addr; +extern void __init socfpga_reset_init (void ); +void __init socfpga_sysmgr_init (void ) {struct device_node *np;
@@ -64,6 +66,7 @@ static void __init socfpga_init_irq(void)if (IS_ENABLED (CONFIG_EDAC_ALTERA_OCRAM ))socfpga_init_ocram_ecc (); +socfpga_reset_init (); }static void __init socfpga_arria10_init_irq (void )
@@ -74,6 +77,7 @@ static void __init socfpga_arria10_init_irq(void)socfpga_init_arria10_l2_ecc ();if (IS_ENABLED (CONFIG_EDAC_ALTERA_OCRAM ))socfpga_init_arria10_ocram_ecc (); +socfpga_reset_init (); }static void socfpga_cyclone5_restart (enum reboot_mode mode,const char *cmd)
drivers/reset/Kconfig +9 -1
@@ -109,7 +109,7 @@ config RESET_QCOM_PDC config RESET_SIMPLE bool "Simple Reset Controller Driver" if COMPILE_TEST - default ARCH_SOCFPGA || ARCH_STM32 || ARCH_STRATIX10 || ARCH_SUNXI || ARCH_ZX || ARCH_ASPEED + default ARCH_STM32 || ARCH_STRATIX10 || ARCH_SUNXI || ARCH_ZX || ARCH_ASPEED help This enables a simple reset controller driver for reset lines that that can be asserted and deasserted by toggling bits in a contiguous,
@@ -128,6 +128,14 @@ config RESET_STM32MP157 help This enables the RCC reset controller driver for STM32 MPUs. +config RESET_SOCFPGA + bool "SoCFPGA Reset Driver" if COMPILE_TEST && !ARCH_SOCFPGA + default ARCH_SOCFPGA + select RESET_SIMPLE + help + This enables the reset driver for the SoCFPGA ARMv7 platforms. This + driver gets initialized early during platform init calls. + config RESET_SUNXI bool "Allwinner SoCs Reset Driver" if COMPILE_TEST && !ARCH_SUNXI default ARCH_SUNXI
drivers/reset/Makefile +1 -0
@@ -19,6 +19,7 @@ obj-$(CONFIG_RESET_QCOM_AOSS) += reset-qcom-aoss.o obj-$(CONFIG_RESET_QCOM_PDC) += reset-qcom-pdc.o obj-$(CONFIG_RESET_SIMPLE) += reset-simple.o obj-$(CONFIG_RESET_STM32MP157) += reset-stm32mp1.o +obj-$(CONFIG_RESET_SOCFPGA) += reset-socfpga.o obj-$(CONFIG_RESET_SUNXI) += reset-sunxi.o obj-$(CONFIG_RESET_TI_SCI) += reset-ti-sci.o obj-$(CONFIG_RESET_TI_SYSCON) += reset-ti-syscon.o
drivers/reset/reset-simple.c +3 -10
@@ -109,7 +109,7 @@ struct reset_simple_devdata {#define SOCFPGA_NR_BANKS 8static const struct reset_simple_devdata reset_simple_socfpga = { - .reg_offset =0x10 , + .reg_offset =0x20 , .nr_resets =SOCFPGA_NR_BANKS *32 , .status_active_low = true, };
@@ -120,7 +120,8 @@ static const struct reset_simple_devdata reset_simple_active_low = { };static const struct of_device_id reset_simple_dt_ids[] = { - { .compatible ="altr,rst-mgr" , .data = &reset_simple_socfpga }, + { .compatible ="altr,stratix10-rst-mgr" ,"altr,rst-mgr" , + .data = &reset_simple_socfpga }, { .compatible ="st,stm32-rcc" , }, { .compatible ="allwinner,sun6i-a31-clock-reset" , .data = &reset_simple_active_low },
@@ -166,14 +167,6 @@ static int reset_simple_probe(struct platform_device *pdev) data->status_active_low = devdata->status_active_low; } -if (of_device_is_compatible (dev->of_node,"altr,rst-mgr" ) && -of_property_read_u32 (dev->of_node,"altr,modrst-offset" , - ®_offset)) { -dev_warn (dev, -"missing altr,modrst-offset property, assuming 0x%x!\n" , - reg_offset); - } - data->membase += reg_offset;return devm_reset_controller_register (dev, &data->rcdev);
drivers/reset/reset-socfpga.c new file +88 -0
88 lines not on this page · raw message
Signature · 1 line
2.17.1
Philipp Zabel
maintainerHi Dinh,
drivers/reset/reset-simple.c static const struct reset_simple_devdata reset_simple_active_low = { · line 123
Quoted 6 lines · Dinh Nguyen
drivers/reset/reset-simple.c +1
-1@@ -120,7 +120,8 @@ static const struct reset_simple_devdata reset_simple_active_low = { };static const struct of_device_id reset_simple_dt_ids[] = { - { .compatible ="altr,rst-mgr" , .data = &reset_simple_socfpga }, + { .compatible ="altr,stratix10-rst-mgr" ,"altr,rst-mgr" ,
This should be
+ { .compatible = "altr,stratix10-rst-mgr",
instead. The rest looks good to me. If you are ok with this change, I can fix it up when applying.
regards
Philipp
Dinh Nguyen
maintainerQuoted 12 lines · Philipp Zabel
Hi Dinh,
drivers/reset/reset-simple.c static const struct reset_simple_devdata reset_simple_active_low = { · line 123
Quoted 6 lines · Dinh Nguyen
drivers/reset/reset-simple.c +1
-1@@ -120,7 +120,8 @@ static const struct reset_simple_devdata reset_simple_active_low = { };static const struct of_device_id reset_simple_dt_ids[] = { - { .compatible ="altr,rst-mgr" , .data = &reset_simple_socfpga }, + { .compatible ="altr,stratix10-rst-mgr" ,"altr,rst-mgr" ,This should be
Quoted 5 lines
+ { .compatible = "altr,stratix10-rst-mgr",
instead. The rest looks good to me. If you are ok with this change, I can fix it up when applying.
Sure..thanks,
Dinh